MSR/MSB Mechanical Setting ToolFEATURES:• Special designed Bow Spring provides positive control and

allows one size Mechanical Setting Tools to cover a large rangeof casing weight

• The upper slips are held in a safe retracted position whilerunning

• Allows users to set, pressure test tubing, and squeeze in a singletrip

• Can quickly be configured to set MMR Cement Retainers orMMB Bridge Plugs

• These tools can be used to run a number of competitive brandBaker style cement retainers or bridge plugs

1

Tech Unit No: 0620000004 Revision: B

Approved By: Quality Engineer Date: 2014-12-16

CASING TOOL

O.D.(in)

WT.(lbs)

SETTINGSLEEVE O.D.

(in)

I.D.(in)

STANDARDBOX UP

4-1/2 9.5-15.13.593

0.872-3/8” EU

8 RD

5 11.5-20.8

5-1/2 13-23 4.310

5-3/4 14-26 4.700

6-5/8 17-32 5.375

1.252-7/8” EU

8 RD

7 17-35 5.687

7-5/8 24-49 6.312

8-5/8 29.3-58.4 7.125

9-5/8 32.75-60.7 8.125

10-3/4 60-83 9.430

11-3/438-60 9.937

48-80.7 10.437

13-3/8 65-118 11.880

16 94-133 14.125

20 9.5-15.1 18.375

General Operation:

When it is advantageous to run a Map Oil ToolsCement Retainer on tubing or drill pipe, a mechanical

setting tool is used. It is designed to contain theupper slips of the cement retainer in a safe retracted

position while running to setting depth. The upperslips are released by right hand rotation and slack offof the work string. The cement retainer is then setand locked to the casing by pulling the appropriateamount of tension against the tool. The slide valve isin the open position while being run into the hole.When the setting procedure is completed, the slidevalve may be closed by picking up (2) two inches atthe tool or opened by slacking off (2) two inches atthe tool. With the slide valve in the closed position,the work string may be hydraulically tested.

The mechanical running tool is released from thecement retainer by right hand rotation. The settingtool contains a built in snap-out feature whichprovides approximately 5,000 # snap out indicationwhen the work string is picked up to close the valve.This tension indicator is reengaged each time thework string is lowered to open the slide valve.

The mechanical setting tool is equipped with drag

springs to assure positive control during running and

setting procedures at all depths or in highly deviated

wells. The mechanical setting tool may be converted

from use with a cement retainer to a bridge plug by

changing the top coupling, stinger sub, and removing

the stinger seal.

Special Notes:

It is recommended to run a gage ring, bit, and casingscraper to setting depth, then circulate two fullcasing columns to clear debris from the wellbore.

When there is possibility that you will havedifficulty stabbing back in to the retainer due towellbore deviation, it is recommended thatcentralizers be run above the mechanical settingtool.

If wellbore fluids or debris may be present, it isrecommended that rotational release occur aftercompleting pumping operations as debris that fallsinto the ID of the tool may prevent the valve fromfunctioning properly and may prevent the settingtool from stinging back into the tool.

2

Running Instructions:1. Make up the top sub of the running tool to thelower pin end of the work string. Use a goodquality, API approved thread lubricant and torqueall work string connections to the manufacturer’storque recommendations. During run in, extremecare should be taken to avoid right hand rotationbeing transmitted to the setting tool. As aprecaution, one left hand turn should be placed inthe work string every 10-15 stands.2. When the desired setting depth has beenreached, tools should be picked up (2) two feetabove the desired setting point. This movement isnecessary to provide the required tool stroke torelease the cement retainer upper slips and allowthe setting tool nut to move freely.3. Rotate the work string to the right sufficiently totransmit 10 turns to the tool. This rotation willthread the control nut off of the mandrel’s matingthread and release the control sleeve and settingsleeve form the controlled position.4. Lower the tools back down to the desired settingpoint, the drag springs will support the controlsleeve and setting sleeve of the setting tool. Thedownward motion of the mandrel will move thecement retainer upper slips form under the settingsleeve. The slips are forced outward toward thecasing wall by the leaf springs inside of each slipsegment. When the slips are released, there issufficient clearance for the locking dog to moveoutward and release the control latch form thestinger sub body.5. Pull the recommended tension over pipe weight(at the tools) to set the slips and affect full pack off.

6. Set down the equivalent amount of weight andpull tension a second time. Once the tool is set,slight up strain may be applied to shift the valveclosed, at which point the tubing can be tested.

SIZE TOOL MIN. TENSION MAX. TENSION

4 1/2 - 5 1/2 25,000 30,000

6 5/8 - 7 35,000 45,000

7 5/8 - 20 40,000 55,000

3

7. Release the setting tool from the cement retainerby pulling 500 lbs. of tension at the tool androtating the work string 10 turns to the right. Thismotion will shear the brass shear screws andunscrew the setting tool control latch from the topof the cement retainer mandrel.

8. The setting tool may be re-latched to the cementretainer by setting down 1000 -3000 lbs. of workstring weight. Set down weight equal to thecalculated weight required to prevent the slidevalve from closing during pumping operations.Always hold and monitor 200 psi pressure on theannulus while squeezing through a cement retainer.Recommended max flow rate is 5 bpm. Higher flowrates may be achieved, but variations in pumpvolume, fluid density, fluid viscosity and pump rateswill have varying effects on stinger and retainershoe wash out which may result in the retainer’sinability to close and isolate wellbore pressurebelow the tool.

9. Now you may snap out of the retainer by pulling5000-8000 lbs. tension at the tool. The setting toolseal will remain in the cement retainer until thecontrol snap force is exceeded. Each time thecontrol latch is snapped in and out of the retainer,the force required to do so will be reduced until theforce to snap in reaches 500 lbs. and the force tosnap out reaches 5,000 lbs.

SPECIAL NOTE: In wells where paraffin orsuspended solids are present in the well bore fluids,the dog in the control latch may not fully releasefrom the stinger sub body. This is indicated whenthe cement retainer sets properly, per steps 1 thru4, but the slide valve will not close so that a tubingpressure test can be performed. In this case, thetubing should be alternately picked up and slackedoff. This motion will cause the dog to move outwardon the inclined edges of the control groove in thestinger sub body and free it for the required verticalmotion.

If this condition is known to exists before the runis made, it is recommended that the mandrel,stinger sub body, control latch, and control sleevebe packed with grease to prevent the intrusion oftrouble fluids.

Mounting the Mechanical Set Cement Retainer tothe Mechanical Setting Tool:

1. Place the top collar of the setting tool in the vise.

2. Move the drag assembly downward until itpositions the control nut clutch and the control nutadjacent to one another. Rotate the mechanism tothe right until it engages the clutch and stops.

3. Rotate the setting sleeve toward the dragassembly until the upset of the control latch isexposed.

4. Slide the upper slips over the stinger sub body.Loosen the clamp on the slips only enough to slidethem over the upset on the control latch and thenretighten the clamp.

5. Lubricate the non-wicker portion of the slips withgrease. Rotate the setting sleeve downward overthe slips until the setting sleeve contacts the hoseclamp. Remove the clamp from the slips andcontinue rotating the setting sleeve downward untilit bottoms out against the wickers of the slips. Backthe setting sleeve off 3 turns. Check to see that theclutch mechanism is still properly shouldered.Readjust the setting sleeve, if necessary.

6. Lubricate the stinger sub and latch lightly withgrease.

7. Slide the cement retainer over the stinger. (Makesure that the retainer remains level during thisoperation. Special care must be taken to ensurethat the stinger properly engages the valve colletfingers.) Drive the retainer on to the stinger sealuntil it shoulders on the latch thread.(Use a woodenblock for this operation.) Bump the bottom of theretainer and rotate it to the make up the LEFTHAND thread on the latch until the retainerbottoms out on the control latch.

8. Align the threaded holes of the retainer bodywith the corresponding holes in the control latchand install the shear screws. (4 1/2”-6 5/8” there isonly one set of holes, 7”-8 5/8” will used lowerholes, 9 5/8” on up will use upper holes.)

9. Rotate the setting sleeve downward until itcontacts the wickers of the slips. Back up ½ turn andinstall the set screws in the setting sleeve.

10. Install the hose clamp about the wickers of theupper slips and tighten for transportation purposes.

REMOVE THE HOSE CLAMP FROM THE SLIPSBEFORE RUNNING THE TOOLS INTO THE WELL

4

Casing OD

(in)

Casing

Weight

Range

(lbs)

Mechanical Setting Tool

MSB

For use with

MWR and MWB-1

MSR

For use with

MMR and MMB

Approx.

Weight

KG LBS

4-1/2 9.5-15.10620359004 0620359005 45 100

5 11.5-20.8

5-1/2 13-23 0620431004 0620431005 30 66

5-3/4 14-26 0620470004 0620470005 42 93

6-5/8 17-32 0620537004 0620537005 72 158

7 17-35 0620568004 0620568005 80 176

7-5/8 20-39 0620631004 0620631005 75 165

8-5/8 24-49 0620712004 0620712005 80 176

9-5/8 29.3-58.4 0620812004 0620812005 110 242

10-3/4 32.75-60.7 0620943004 0620943005 125 275

11-3/460-83 0620994004 0620994005 135 297

38-60 0621043004 0621043005 148 326

13-3/8 48-80.7 0621188004 0621188005 170 374

16 65-118 0621412004 0621412005 195 430

20 94-133 0621837004 0621837005 290 638

5

Model "MSR" Mechanical Setting ToolPart List – 4 ½” – 5 ¾”

Item Description Qty

Size and Part Number

4 1/2" & 5" 5 1/2" 5 3/4"

0620359005 0620431005 0620470005

1 COUPLING 1 0620431050

2 MANDREL 1 0620431052

3 UPPER DRAG COLLAR 1 0620431053

4 UPPER DRAG RING 1 0620431054

5 SOCKET HEAD SCREW 3 0545602296

6 DRAG SPRING 6 0515480083 0620431083

7 RETAINER 1 X20-25-118

8 LOWER DRAG RING 1 0620431054

9 LOWER DRAG COLLAR 1 0620431055

10 CONTROL SLEEVE 1 0620431060

11 SOCKET HEAD SCREW 4 0545602096

12 SOCKET HEAD SCREW 3 0545602296

13 SOCKET HEAD SCREW 2 0545605077 0545602697

14 CONTROL NUT ASSY. 1 0620431061

15 CONTROL NUT CLUTCH 1 0620431062

16 RETAINING SLEEVE 1 0620431063

17 O-RING 1 000P569219

18 SOCKET HEAD SCREW 2 0800000336

19 DOG 1 0620431064

20 DOWEL PIN 2 0620568073

21 SPRING 2 0620431173

22 SETTING SLEEVE 1 0620359065 0620431065 0620470065

23 CONTROL LATCH 1 0620431068

24 KEY 1 0620568067

25 STINGER SUB BODY 1 0620431069

26 SEAL 1 0515480058

27 O-RING 1 000P569024

28 SLIDING VALVE STINGER 1 0620431070

29 PIN THREAD PROTECTOR 1 0596003051

30 SEAL REDRESS KIT NA 0620359200

31 SCREW REDRESS KIT NA 0620359250

32 CONVERSION KIT TO MSB NA 0620431145

6 5/8”- 20” Model "MSR" Mechanical Setting ToolPart List

Item Description Qty

Size and Part Number

6 5/8" 7" 7 5/8" 8 5/8" 9 5/8" 10 3/4" 11 3/4"60-83#

11 3/4"38-60# 13 3/8" 16" 20"

0620537005 0620568005 0620631005 0620712005 0620812005 0620943005 0620994005 0621043005 0621188005 0621412005 06218370051 COUPLING 1 06205680502 MANDREL 1 06205680523 UPPER DRAG COLLAR 1 0620568053 0620631053 0620712053 0620943053 0620994053 0621188053 0621412053 06218370534 UPPER DRAG RING 1 0620568054 0620631054 0620712054 0620943054 0620994054 0621188054 0621412054 06218370545 SOCKET HEAD SCREW See Size 0545602296 (Qty: 3) 0545602296 (Qty: 6)6 DRAG SPRING 6 0620431083 0620568083 0620712056 0620812056 0620712056 0620812056 0620812056 (Qty: 9)7 RETAINER 1 X20-25-1168 LOWER DRAG COLLAR 1 0620568055 0620631055 0620712055 0620943055 0620994055 0621188055 0621412055 06218370559 SNAP RING 1 0620568057

10 LOWER DRAG RING 1 0620568056 0620631056 0620712054 0620943054 0620994054 0621188054 0621412054 062183705411 DRAG COLLAR INSERT 1 062056805812 SOCKET HEAD SCREW 4 0545602297 054567409113 RETAINING WASHER 1 062056805914 CONTROL SLEEVE 1 062056806015 CONTROL NUT ASSY. 1 062056806116 SOCKET HEAD SCREW 2 0545605077 0545602697 0545605075 054560269717 CONTROL NUT CLUTCH 1 062056806218 O-RING 1 000P56922519 SOCKET HEAD SCREW 2 080000033620 RETAINING SLEEVE 1 0620568063

Continued on next page

6

6 5/8”- 20” Model "MSR" Mechanical Setting ToolPart List - continued

Item Description Qty

Size and Part Number

6 5/8" 7" 7 5/8" 8 5/8" 9 5/8" 10 3/4" 11 3/4"60-83#

11 3/4"38-60# 13 3/8" 16" 20"

0620537005 0620568005 0620631005 0620712005 0620812005 0620943005 0620994005 0621043005 0621188005 0621412005 0621837005

21 DOG 1 0620568064

22 SETTING SLEEVE 1 0620568065 0620631065 0620712065 0620812065 0620943065 0620994065 0621043065 0621188065 0621412065 0621837056

23 KEY 1 0620568067

24 DOWEL PIN 2 0620568073

25 SLIP ADAPTER 1 Not Required 0620631069 0620712069 0620812069 0620943069 0620994069 0621043069 0621188069 0621412069 0621837059

26 SOCKET HEAD SCREW 4 Not Required 0545635296 0620712070 0620812070 X20-05-543 0621188070 0545602493 0621412070 0620812070

27 SPRING 2 0515884060

28 SPACER 4 Not Required 0620712074 Not Required 0620712074 Key - 0621837064 Qty. - 2

29 CONTROL LATCH 1 0620568068 0620631068 0621837068

30 STINGER SUB BODY 1 0620568069

31 SEAL 1 0515484058

32 O-RING 1 000P569130

33 SLIDING VALVE STINGER 1 0620568070

34 PIN THREAD PROTECTOR 1 0596003053

35 SEAL REDRESS KIT NA 0620568200

36 SCREW REDRESS KIT NA 0620568115

37 CONVERSION KIT TO MSB NA 0620568145

7

8

Assembly Instructions4 1/2", 5 1/2" and 5 3/4" Mechanical Setting Tool.

1. Thread Control Nut Clutch (15) onto threads on lower end or Mandrel (2) until itshoulders out.

2. Thread Control Nut Assembly (14) onto control threads until clutch surface of Control Nut and ControlNut Clutch engage.

3. Slide Lower Drag Ring (8) and Lower Drag Collar (9) over mandrel.

4. Slide Tru-Arc Retainer (7) over the Mandrel and locate into groove.

5. Slide Upper Drag Collar (3) and Drag Ring onto Mandrel. Insert Drag Springs into slots on Upper DragCollar and slide Drag Ring over Drag Springs. Align holes and install Cap Screws (5).

6. Insert Drag Springs (6) into slots on Lower Drag Collar and slide Drag Ring over Collar and Springs.Install Cap Screws (12) into mating holes of Lower Drag Collar and Lower Drag Ring.

7. Thread Coupling (1) onto Mandrel. Place Coupling in a vise and tighten Mandrel to Couplingconnection with a pipe wrench. Place wrench in the under cut wrenching area on Mandrel.

8. Slide Retaining Sleeve (16) through Control Sleeve (10) and engage Retaining Sleeve upper externalshoulder with Control Sleeve's lower internal shoulder.

9. Align internal keyway in Control Sleeve with key on Control Nut and slide Control Sleeve up overControl Nut and Mandrel until Retaining Sleeve shoulder is against Control Nut.

10. Make-up Lower Drag Collar into Control Sleeve hand tight. Unscrew Lower Drag Collar out untilthreaded holes for Cap Screws (11) can be seen through mating holes in Control Sleeve. Install CapScrews and tighten. Care should be taken during this procedure to prevent the Control Nut from backingoff.

11. Screw Setting Sleeve (22) onto Control Sleeve until Setting Sleeve upper end contacts the upset onControl Sleeve.

12. Coat Dog Springs (21) with grease and insert into appropriate holes in Control Latch (23). Insert Dog(19), Dowel Pins (20) and Set Screws (18) into Control Latch. Be sure that the Dowel Pins trap the Dog inthe Control Latch.

4 ½-5”, 5 ½”, 5 ¾” MSR

9

13. Place Key (24) into vertical slot on Stinger Sub Body (25). Align keyway in Control Latch withKey and slide Control Latch onto Stinger Sub Body. Install O-ring (17) on Stinger Sub Body. Alignand depress Dog into locking groove of Stinger Sub Body and make up into the lower end of theMandrel. The Dog must move under the Retaining Sleeve as the Stinger Sub Body and Mandrelare made up. Make up wrench tight.

14. Insert O-ring (27) into groove inside of Stinger Seal (26). Install Stinger Seal on Stinger SubBody. Install Slide Valve Stinger (28) on Stinger Sub Body. Make up wrench tight

15. Screw Setting Sleeve (22) down onto control Sleeve and install Set Screws (13).

16. Double check Control Nut Assembly is bottomed out on the Control Nut Clutch by spinningthe Drag Springs to the (RIGHT) with the Coupling still held in the vise.

Disassembly Instructions4 1/2", 5 1/2" and 5 3/4" Mechanical Setting Tool.

1. Clamp Coupling (1) in vise. Loosen and remove Slide Valve Stinger (28) from Stinger Sub Body(25). Remove Stinger Seal (26) and O-Ring (27).

2. Loosen and remove Stinger Sub Body/Control Latch subassembly from the Mandrel (2).Remove O-Ring (17) and slide Control Latch (23) off of Stinger Sub Body.

3. Remove Set Screws (18) from Control Latch. Turn Control Latch upside down and depress Dog(19) to remove Dowel Pins (20). Remove Dog and Springs (21).

4. Remove Set Screws (13) from Setting Sleeve (22) and unscrew Setting Sleeve from ControlSleeve (10).

5. Remove Cap Screws (11) and unscrew Lower Drag Collar (9) from Control Sleeve and removeControl Sleeve. Remove Retaining Sleeve (16) from Control Sleeve.

6. Remove Cap Screws (5) from Upper Drag Collar (3) and slide Upper Drag Ring (4) off of UpperDrag Collar.

7. Remove Cap Screws (12) from Lower Drag Collar (9) and slide Lower Drag Ring (8) off andremove Drag Springs (6).

8. Loosen Mandrel (2) from Coupling. Place wrench in under cut on Mandrel .

9. Remove Tool from Vise and Remove Coupling (1).

10. Remove Upper Drag collar and Upper Drag Ring from Mandrel. Remove Tru-Arc Retainer (7).

11. Remove Lower Drag Collar from Mandrel.

12. Remove Control Nut Assembly (14). Do not remove Control Nut Clutch (15) unless required.

10

6 5/8” & 7” MSR

Assembly Instructions6 5/8” – 20” Mechanical Setting Tool

1. Thread Control Nut Clutch (17) onto threads on lower end of Mandrel (2) until it shoulders out.

2. Thread Control Nut Assembly (15) onto control threads until clutch surface of Control Nut andControl Nut Clutch engage.

3. Slide Retaining Washer (13), Drag Collar Insert (11) (large ID down) and Snap Ring (9) over Mandrel.Depress Snap Ring into groove on Mandrel with a hose clamp or Chain Vise Grip. Slide small ID of DragCollar Insert over Snap Ring and remove hose clamp. Leave top of Snap Ring and top of the Drag CollarInsert flush.

4. Slide Lower Drag Ring (10) and Lower Drag Collar (8) onto Mandrel. Slide Lower Drag Collar over DragCollar Insert until Drag Collar Insert is seated in counter bore of Lower Drag Collar. This will trap theSnap Ring in the recess of the Mandrel.

5. Slide Tru-Arc Retainer (7) over the Mandrel and locate into groove.

6. Slide Upper Drag Collar (3) and Upper Drag Ring (4) onto Mandrel.

7. Thread Coupling (1) onto Mandrel. Place Coupling in a vise and tighten Mandrel to Couplingconnection with a pipe wrench. Place wrench in the under cut wrenching area on Mandrel.

8. Insert Drag Springs (6) into slots on Lower Drag Collar and slide Lower Drag Ring over Drag Springs.Align holes and install Cap Screws (5).

9. Insert Drag Springs into slots on Upper Drag Collar and slide Upper Drag Ring over Drag Springs. Alignholes and install Cap Screws (5).

10. THIS STEP FOR 6 5/8”-7” ONLY. Seat Retaining Washer (13) against matching shoulder insideControl Sleeve.

11. Make up Lower Drag Collar into Control Sleeve hand tight. Unscrew Lower Drag Collar out untilthreaded holes for Cap Screws (12) can be seen through the mating holes in Control Sleeve. Install CapScrews and tighten. Care should be taken during this procedure to prevent the Control Nut frombacking off.

6 5/8”-20” MSR

11

12. Screw Setting Sleeve (22) onto Control Sleeve (14) until Setting Sleeve upper end contacts theupset on Control Sleeve.

13. Coat Dog Springs (27) with grease and insert into appropriate holes in Control Latch (29). Insert Dog(21), Dowel Pins (24) and Set Screws (19) into Control Latch. Be sure that the Dowel Pins trap the Dogin the Control Latch.

14. THIS STEP FOR 7 5/8” – 20” ONLY. Install Slip Adapter (25) and secure with Flat Head Screws (26).

15. Place Key (23) into vertical slot on Stinger Sub Body (30). Align keyway in Control Latch with Key andslide Control Latch onto Stinger Sub Body. Install O-ring (18) on Stinger Sub Body. Align and depressDog into locking groove of Stinger Sub Body and make up into the lower end of the Mandrel. The Dogmust move under the Retaining Sleeve as the Stinger Sub Body and Mandrel are made up. Make upwrench tight.

16. THIS STEP FOR 8 5/8”-11 ¾” 60-83# & 16”. THE 20” TOOL USES 2EA KEYS. Install Spacers (28) into slot on Control Latch with the long bevel facing the collet side of the Control Latch.

17. THIS STEP FOR 7 5/8” – 20”. Install Slip Adapter (25) over Spacers onto Control Latch and securewith Socket Head Screws (26)

18. Insert O-ring (32) into groove inside of Stinger Seal (31). Install Stinger Seal on Stinger Sub Body.Install Slide Valve Stinger (33) on Stinger Sub Body. Make up wrench tight.

19. Screw Setting Sleeve back down onto Control Sleeve and install Set Screws (16).

20. Confirm that the Control Nut Assembly is bottomed out on the Control Nut Clutch by spinning theDrag Springs to the right with the Coupling still held in the vise.

Disassembly Instructions6 5/8”-20” Mechanical Setting Tool

1. Clamp Coupling (1) in vise. Loosen and remove Slide Valve Stinger (33) from Stinger Sub Body (30).Remove Stinger Seal (31) and O-ring (32).

2. Loosen and remove Stinger Sub Body/Control Latch subassembly from the Mandrel (2). Remove O-ring (18) and slide Control Latch (29) off Stinger Sub Body.

3. Remove Key (23) from Stinger Sub Body.

4. EXCLUDE THIS STEP FOR 6 5/8”-7”. Remove Socket Head Screws (26) and Slip Adapter (25). SlideSlip Adapter off of Control Latch

5. EXCLUDE THIS STEP FOR 6 5/8”-7 5/8”, 11 ¾” 38-60#, & 13 3/8”. THE 20” USES 2EA KEYS. RemoveSpacers (28) from Control Latch.

12

6. Remove Set Screws (19) from Control Latch. Turn Control Latch upside down and depress Dog (21) toremove Dowel Pins (24). Remove Dog and Springs (27).

7. Remove Set Screws (16) from Setting Sleeve (22) and unscrew Setting Sleeve from Control Sleeve(14).

8. Remove Cap Screws (12) and unscrew Lower Drag Collar (8) from Control Sleeve and remove ControlSleeve. Remove Retaining Sleeve (20) from Control Sleeve.

9. Remove Cap Screws (5) from Lower Drag Collar then slide Lower Drag Ring (10) off.

10. Remove Cap Screws (5) from Upper Drag Collar (3) and slide Upper Drag Ring (4) off. Remove DragSprings (6).

11. Loosen Mandrel from Coupling. Place wrench in under cut on Mandrel. Remove Coupling.

12. Remove Upper Drag collar and Upper Drag Ring from Mandrel. Remove Tru-Arc Retainer (7).

13. Remove Lower Drag Collar and Lower Drag Ring from Mandrel. Remove Snap Ring (9), Drag CollarInsert (11) and Retaining Washer (13).

14. Remove Control Nut Assembly (15). Do not remove Control Nut Clutch (17) unless required.

Ragen

Text Box

13

Tool Size

OD (in)

4 1/2

5

5 1/2 0620431005

5 3/4 0620470005

6 5/8 0620537005 2.539 8.203

7 0620568005 2.726 8.578

7 5/8 0620631005 2.949 9.023

8 5/8 0620712005 0620712056 1.938 0.016 14.250 0.063 3.418 9.960

9 5/8 0620812005 0620812056 2.125 0.005 14.125 0.130 3.605 10.335

10 3/4 0620943005 3.935 10.995

0620994005 4.435 11.995

0621043005 4.623 12.370

13 3/8 0621188005 5.530 14.185

14 0621238005 5.846 14.817

16 0621412005 6.752 16.629

20 0621837005 8.649 20.423

Tool Size

OD (in)

4 1/2

5

5 1/2 0620431005

5 3/4 0620470005

6 5/8 0620537005 2.258 7.640

7 0620568005 2.758 8.640

7 5/8 0620631005 2.980 9.085

8 5/8 0620712005 0620712056 1.688 0.203 3.168 9.460

9 5/8 0620812005 0620812056 2.063 0.203 3.543 10.210

10 3/4 0620943005 3.685 10.495

0620994005 4.185 11.495

0621043005 4.560 12.245

13 3/8 0621188005 5.468 14.060

14 0621238005 5.784 14.692

16 0621412005 6.689 16.504

20 0621837005 8.586 20.298

MAP Oil Tools Drag Spring Inspection Criteria

0620712056 1.938 0.016 14.250 0.063

Tolerance

(in)

MSR Part

Number

QTY of

Springs

Drag Spring

Part Number

Arch

Height

(in)

Tolerance

(in)

Free

Length

(in)

Tolerance

(in)

Min

Thickness

(in)

Max

Thickness

(in)

Arch Height

Installed (in)

Tolerance

(in)

Arch Diameter

Installed (in)

0.250

0620431083 1.9381.938 5.795

0620568083 2.125 14.190

0.060 1.732

0.100

5.384

0.065

0515480083

0.095

11 3/4

9

0.0056

1.344 14.060

0620812056 2.125 0.005

14.250

MSR Part

Number

QTY of

Springs

Drag Spring

Part Number

Arch

Height

(in)

Tolerance

(in)

Free

Length

(in)

0.016

0.0800620359005

14.125 0.130

0.063

Arch Height

Installed (in)

Tolerance

(in)

Arch Diameter

Installed (in)

1.482

0.100

4.884

0.250

0620431083 1.656 14.250 0.063

0.203

1.094

0.063

14.060 0.060

0.080 0.175

Tolerance

(in)

Min

Thickness

(in)

Max

Thickness

(in)

Setting Tools Purchased Prior To November 2014

11 3/4

9

0620568083 2.156 14.060 0.060

14.125 0.063

0.172

0.204

0.095

2.044 6.009

0620712056 1.688 0.203

0620812056 2.063

Setting Tools Purchased After November 2014

Tolerance

(in)

0620359005

6

0515480083

14