MS:124 ASSEMBLY MANUAL · 2018. 7. 15. · MS:124 “Graphics and specifications may change without notice”. ASSEMBLY MANUAL Specifications: Wing span -----65in (165cm). Wing area

MS:124

“Graphics and specifications may change without notice”.

ASSEMBLY MANUAL

Specifications:Wing span ------------------------------65in (165cm).Wing area -----------------658.8sq.in (42.5sq dm).Weight -------------------------10.4-11lbs (4.7-5kg).Length ------------------------------62.4in (158.4cm).Engine ---------------- 0.91-1.00cu.in ----2-stroke. 1.00-1.25cu.in ----4-stroke.Radio --------------------6 channels with 9 servos.Retracts landing gear (included).

SUPER TUCANO. Instruction Manual.

2

INTRODUCTION.

Thank you for choosing the SUPER TUCANO ARTF by SEAGULL MODELS. The SUPERTUCANO was designed with the intermediate/advanced sport flyer in mind. It is a semi scaleairplane which is easy to fly and quick to assemble. The airframe is conventionally built using balsa,plywood to make it stronger than the average ARTF , yet the design allows the aeroplane to be keptlight. You will find that most of the work has been done for you already.The motor mount has beenfitted and the hinges are pre-installed . Flying the SUPER TUCANO is simply a joy.

This instruction manual is designed to help you build a great flying aeroplane. Please read thismanual thoroughly before starting assembly of your SUPER TUCANO. Use the parts listing belowto identify all parts.

WARNING.

Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it iscapable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOUASSUME ALL RISK & RESPONSIBILITY.

If you are inexperienced with basic R/C flight we strongly recommend you contact your R/C supplierand join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of trainingprocedures designed to help the new pilot on his way to successful R/C flight. They will also be ableto advise on any insurance and safety regulations that may apply.

KIT CONTENTS

1

2

9

3 4

55

8

6

7

10111111

3

www.seagullmodels.com

ADDITIONAL ITEMS REQUIRED.

0.91-1.00 2-stroke. 1.00-1.25 4-stroke.

Computer radio with 9 servos.Glow plug to suit engine.Propeller to suit engine.Protective foam rubber for radiosystem.Silicone fuel line.

TOOLS & SUPPLIES NEEDED.

Thick cyanoacrylate glue.30 minute epoxy.5 minute epoxy.Hand or electric drill.Assorted drill bits.Modelling knife.Straight edge ruler.2mm ball driver.Phillips head screwdriver.220 grit sandpaper.90° square or builder’s triangle.Wire cutters.Masking tape & T-pins.Thread-lock.Paper towels.

The control surfaces, including theailerons, elevators, and rudder, areprehinged with hinges installed, butthe hinges are not glued in place. Itis imperative that you properlyadhere the hinges in place per thesteps that follow using a high-qualitythin C/A glue.

2) Remove each hinge from the wing paneland aileron and place a T-pin in the center ofeach hinge. Slide each hinge into the aileronuntil the T-pin is snug against the aileron. Thiswill help ensure an equal amount of hinge ison either side of the hinge line when the aileronis mounted to the wing panel.

HINGING THE AILERONS .

Note:

Hinge.

T-pin.

KIT CONTENTS.

1 Fuselage2 Canopy3 Left wing panel4 Right wing panel5 Tail set6 Aluminum wing tube7 Scale pilot8 Fiberglass cowl9 Retracts landing gear10 EP conversion pack11 Hardware bag included

3) Slide the aileron on the wing panel untilthere is only a slight gap. The hinge is nowcentered on the wing panel and aileron.Remove the T-pins and snug the aileronagainst the wing panel. A gap of 1/64” or lessshould be maintained between the wing paneland aileron.

1) Carefully remove the aileron from oneof the wing panels. Note the position of thehinges.


4

8) After both ailerons are securely hinged,firmly grasp the wing panel and aileron tomake sure the hinges are securely glued andcannot be pulled out. Do this by carefullyapplying medium pressure, trying to separatethe aileron from the wing panel. Use cautionnot to crush the wing structure.

7) Repeat this process with the other wingpanel, securely hinging the aileron in place.

Work the aileron up and down severaltimes to “work in” the hinges andcheck for proper movement.

Note:

4)Deflect the aileron and completelysaturate each hinge with thin C/A glue. Theailerons front surface should lightly contact thewing during this procedure. Ideally, when the

The hinge is constructed of a specialmaterial that allows the C/A to wickor penetrate and distributethroughout the hinge, securelybonding it to the wood structure ofthe wing panel and aileron.

hinges are glued in place, a 1/64” gap or lesswill be maintained throughout the lengh of theaileron to the wing panel hinge line.

Note:

Hinge.

6) Using C/A remover/debonder and apaper towel, remove any excess C/A glue thatmay have accumulated on the wing or in theaileron hinge area.

5) Turn the wing panel over and deflect theaileron in the opposite direction from theopposite side. Apply thin C/A glue to eachhinge, making sure that the C/A penetrates intoboth the aileron and wing panel.

5


HINGING THE RUDDER.

Glue the rudder hinges in place using thesame techniques used to hinge the ailerons.

INSTALL THE AILERONS CONTROLHORN.

Hinge.

2 sets.

3x35mm.

HINGING THE ELEVATOR.

Glue the elevator hinges in place using thesame techniques used to hinge the ailerons.

Aileron control horn.

C/A glue.

1) Locate the hardware necessary to installthe control horns for the ailerons.

2) Position the control horn on the bottom ofthe aileron. You will see pre-drill hole 3mm forthe horn mounting screw on the aileron.

3) Place epoxy into hole. This will harden thethreads and prevent the crews from pullingloose.

4) Thread a control horn end with aluminumwasher, lock nut until the top edge of the end is18mm from the vase of the horn as shown.

ALUMINUM WASHER.

ALUMINUM WASHER.

CONTROL HORN M3 SCREW.

18mm.

Epoxy.

Wing

Wing

Epoxy.

M3 LOCK NUT.

3mm.


6

Install the flap control horn using the samemethod as same as the aileron control horns.

2 sets.

3x30mm.

Install the elevator control horn using thesame method as same as the aileron controlhorns.

INSTALL ELEVATOR CONTROL HORN.

2 sets.

3x35mm.

Hinge.

Flap control horn.

T-pin.

C/A glue.

C/A glue.

T-pin.

C/A glue.

INSTALL FLAP CONTROL HORN.


M3 lock nut.ALUMINUM WASHER.

18mm.

ALUMINUM WASHER.

Epoxy.

Epoxy.

Flap.

Aluminum Washer.


M3 LOCK NUT.

Epoxy.

Aluminum Washer.

Flap.

7


Repeat steps to install the rudder control hornas same as steps done for ailerons.

1 sets.

3x50mm.

Elevator control horn.

Aluminum Washer.


M3 LOCK NUT.

Epoxy.

Aluminum Washer.

HorizontalStabilizer. Elevator.

18mm.

Epoxy.

HorizontalStabilizer. Elevator.

3mm.

INSTALL RUDDER CONTROL HORN.

Rudder.

Aluminum Washer.


M3 LOCK NUT.

Epoxy.

Aluminum Washer.

Fuselage.

Fuselage.

18mm.

Epoxy.

Rudder.

Rudder control horn.

3mm.


8

5.5mm.

Thread locker glue.

1) Using a modeling knife, carefully cutoff the rear portion of one of the 3 nylon tubesleaving 1/2” protruding from the rear of thestopper. This will be the fuel pick up tube.

INSTALLING THE STOPPER ASSEMBLY.

2) Using a modeling knife, cut one lengthof silicon fuel line. Connect one end of the lineto the weighted fuel pick up and the other endto the nylon pick up tube.

ENGINE MOUNT INSTALLATION.

4x30mm.

1) Locate the items necessary to install theengine mount included with your model. .

2) Use four 4x30mm head bolts and four 4mmwashers to attach the engine mount rails tothe firewall. Tighten the screws . Make sure touse threadlock on the screws to help preventthem from vibrating loose.

9


Vent tube. Fuel pick up tube.

Fuel fill tube.

3) Carefully bend the second nylon tubeup at a 45º angle. This tube is the vent tube.

4) Test fit the stopper assembly into thetank. It may be necessary to remove some ofthe flashing around the tank opening using amodeling knife. If flashing is present, makesure none falls into the tank.

5) With the stopper assembly in place,the weighted pick-up should rest away fromthe rear of the tank and move freely inside thetank. The top of the vent tube should rest justbelow the top of the tank. It should not touchthe top of the tank.

6) When satisfied with the alignment ofthe stopper assembly tighten the 3 x 20mmmachine screw until the rubber stopper ex-pands and seals the tank opening. Do notovertighten the assembly as this could causethe tank to split.

FUEL TANK INSTALLATION.

You should mark which tube is the ventand which is the fuel pickup when you attachfuel tubing to the tubes in the stopper. Oncethe tank is installed inside the fuselage, it maybe difficult to determine which is which.

Fuel tank.

7) Slide the fuel tank into the fuselage. Guidethe lines from the tank through the hole in thefirewall.

8) Use plywood template to hold in placethe fuel tank with C/A glue to secure the fueltank inside the fuselage as shown.

Vent tube.

Fuel pick up tube.

Fuel fill tube.

Balsa wood included.

C/A glue.

Fuel tank.

9) Connect the lines from the tank to the engineand muffler. The vent line will connect to themuffler and the line from the clunk to thecarburetor.


10

Blow through one of the lines to en-sure the fuel lines have not become kinkedinside the fuel tank compartment. Airshould flow through easily.INSTALLING THE FUSELAGE SERVOS.

1) Install the rubber grommets and brasscollets onto the throttle servo. Test fit the servointo the aileron servo mount.

2) Secure the servos with the screws pro-vided with your radio system.

THROTTLE SERVO ARM INSTALLATION.

Install adjustable servo connector in the servoarm as same as picture below.

Servo arm. Loctilesecure.

Adjustable servo connector.

Rudder servo arm.

Throttle servo arm.

Elevator servo.arm

Rudder servo.

Elevator servo.

Throttle servo.

Because the size of servos differ, youmay need to adjust the size of the precut open-ing in the mount. The notch in the sides of themount allow the servo lead to pass through.

DIGITAL SERVO 10 - 12.5KG.

SERVO GEAR INSTALLATION.

Servo for retractable only.

Metal connector.

Servo arm.

25mm.

M3x10mm.

11


Screw.

Screw.

M3x10mm.

3/ 32” Hole.

INSTALLING THE SWITCH.

Install the switch into the precut hole in theside, in the fuselage.




12

3) Use a drill to drill the four holes in the enginemount rails.

4) On the fire wall has the location for thethrottle pusshrod tube (pre-drill).

7) Slide the throttle pushrod wire into the tube.Position the engine between the mounts. Usefour M4x30mm machine screws to secure theengine to the mount as shown.

5) Slide the pushrod tube in the firewall andguide it through the fuel tank mount. Usemedium C/A to glue the tube to the firewall andthe fuel tank mount.

6) Connect the Z-bend in the 450mm throttlepushrod to the outer hole of the carburetor arm.

Machine screw M4x30mm.

Pushrod wire.

4.5mm.

Switch.

Trim and cut.

150mm.

MOUNTING THE ENGINE.

2) Use a pin drill and 4mm drill bit to drill asmall indentation in the mount for the enginemounting screw.

1) Position the engine with the drive washer(150mm) forward of the firewall as shown.

4mm.

4.5mm.

13


8) Reinstall the servo horn by sliding theconnector over the pushrod wire. Center thethrottle stick and trim and install the servo hornperpendicular to the servo center line.

9) Move the throttle stick to the closed positionand move the carburetor to closed. Use a 2.5mmhex wrench to tighten the screw that securesthe throttle pushrod wire. Make sure to usethreadlock on the screw so it does not vibrateloose.

COWLING.

Trim and cut.

Trim and cut.

1) Slide the fiberglass cowl over the en-gine and line up the back edge of the cowl withthe marks you made on the fuselage then trimand cut as shown.

Trim and cut.

Because of the size of the cowl, it may be nec-essary to use a needle valve extension for thehigh speed needle valve. Make this out of suf-ficient length 1.5mm wire and install it into theend of the needle valve. Secure the wire inplace by tightening the set screw in the side ofthe needle valve.


14

INSTALLING THE AILERON - FLAP SERVOS.

Servos. Small weight.

Thread.

INSTALLING THE SPINNER.

Install the spinner backplate, propeller andspinner cone.

The propeller should not touch any partof the spinner cone. If it does, use a

sharp modeling knife and carefully trim awaythe spinner cone where the propeller comesin contact with it.

Because the size of servos differ, youmay need to adjust the size of the precut open-ing in the mount. The notch in the sides ofthe mount allow the servo lead to pass through.

Machine screw M3x10mm.

Needle valve.

3) Install the muffler and muffler extensiononto the engine and make the cutout in thecowl for muffler clearance. Connect the fueland pressure lines to the carburetor, mufflerand fuel filler valve. Secure the cowl to fuse-lage using the 3x10mm screws.

2) While keeping the back edge of thecowl flush with the marks, align the front ofthe cowl with the crankshaft of the engine. Thefront of the cowl should be positioned so thecrankshaft is in nearly the middle of the cowlopening. Use the spinner backplate as a guide.Hold the cowl firmly in place using pieces ofmasking tape.

15


String.Small weight.

1) Using a small weight (Weighted fuel pick-upworks well) and string, feed the string throughthe wing as indicated.

2) Place the servo between the mountingblocks and space it from the hatch. Use a pencilto mark the mounting hole locations on theblocks.

3) Use drill bit in a pin vise to drill the moutingholes in the blocks.

4) Apply 2-3 drops of thin C/A to each of themounting holes. Allow the C/A to cure withoutusing accelerator.

6) Secure the servo to the aileron hatch usingPhillips screwdriver and the screws providedwith the servo.

5) Use dental floss to secure the connectionso they cannot become unplugged.

7) Apply 1-2 drops of thin C/A to each of themounting tabs. Allow the C/A to cure withoutusing accelerator.


16

Attach the string to the servo lead andcarefully thread it though the wing.

M2x6mm.

Flap servo.

Aileron servo.

Wing rib.Small weight.

String.

M2x6mm.

Aileron servo.

Flap servo.

17


Wing.

Aileron.

M2 lock nut.

1) Mark the control wire where it crosses theservo arm hole.

Bend at the mark.

Snap keeper.

Servo arm.

3) Connect the linkage as shown and securethe control wire with a snap keeper.

8mm

Snap keeper.

2) Make a 90-degree bend at the mark and cutoff the excess wire leaving 8mm past the bend.

M2 lock nut. Metal clevis.

AILERON PUSHROD HORN INSTALLATION

Mark.

Pen.

Cut.

8mm.

Repeat the procedure for the other aileron servo.


18

2mm.

2mm.

1.

INSTALLING THE FLAP PUSHROD.

M2 lock nut.

Wing.

Flap.

INSTALLING RETRACTABLELANDING GEAR.

1

2

34

5

6

Cut.

1) Locate the items necessary to install theretracts landing gear and retract linkage instal-lation.

2) Cut the covering from the bottom of thewing for retracts landing gear installation.

4) Position the landing gear onto the landinggear rails. Mark the location of the holes formouting the landing gear.

7

3) Glue hardwood mounting blocks into thewing as show with epoxy.

230mm.

215mm.

7.

Epoxy.

Repeat the procedure for the aileron pushrod.

19


M3x25mm.

M3x25mm.

5.

3.

2.

4.

3.

C/A glue.

6.

5) Install the linkage into the connector on theend of the retract unit as shown. Mounting thelanding gear to the rail with four M3x 25mm.

6) Install a wheel and two wheel collars onthe main landing gear. Secure the collars.

7) Install the wheel wells after adjusting theretracts. Roughen the bottom side of the welland glue the wells using C/A glue as shown.

8) Install the gear door to the retract strut.Apply a thin epoxy to the two gear door brack-ets to secure the gear door to the retract strutas shown.

Cut.


20

Plactic screw.

Plactic screw.

WNG AND THE ARMAMENTS ASSEMBLY.

21


INSTALLING THE HORIZONTAL STABILIZER.

Draw center line.

1) Using a ruler and a pen, locate thecenterline of the horizontal stabilizer, at thetrailing edge, and place a mark. Use a triangleand extend this mark, from back to front,across the top of the stabilizer. Also extendthis mark down the back of the trailing edge ofthe stabilizer.

2) Using a modeling knife, carefully removethe covering at mounting slot of horizontalstabilizer.

Hinge slot.

6) With the stabilizer held firmly in place,use a pen and draw lines onto the stabilizerwhere it and the fuselage sides meet. Do thison both the right and left sides and top andbottom of the stabilizer.

5) When you are satisfied with the align-ment, hold the stabilizer in place with T- pinsor masking tape, but do not glue at this time.

4) Install the stabilizer onto the fuselage.Align the centerline drawn on the top and therear of the stabilizer with the centre of the fu-selage. When that is aligned, hold the stabi-lizer in that position using T-pins or maskingtape. Align the horizontal stabilizer with thewing. When viewed from the rear, the hori-zontal stabilizer should be level with the wing.If it is not level, use sandpaper and sand downthe high side of the stabilizer mounting plat-form until the proper alignment is achieved.The tips of the stabilizer should also be equaldistance from the tips of the wing.

3) Put the stabilizer into place in theposition of the fuselage.

Cut.

Remove the covering.


22

9) When you are sure that everything isaligned correctly, mix up a generous amountof 30 Minute Epoxy. Apply a thin layer to thebottom of the stabilizer mounting area and tothe stabilizer mounting platform sides in thefuselage. Putting the stabilizer in place andrealign. Double check all of your measure-ments once more before the epoxy cures.Hold the stabilizer in place with T-pins or mask-ing tape and remove any excess epoxy usinga paper towel and rubbing alcohol.

Epoxy.

Epoxy.

10) After the epoxy has fully cured, re-move the masking tape or T-pins used to holdthe stabilizer in place. Carefully inspect theglue joints. Use more epoxy to fill in any gapsthat may exist that were not filled previouslyand clean up the excess using a paper toweland rubbing alcohol.

Pen.

When cutting through the covering toremove it, cut with only enough pressureto only cut through the covering itself. Cut-ting into the balsa structure may weakenit.

Remove the covering.

7) Remove the stabilizer. Using the linesyou just drew as a guide, carefully remove thecovering from between them using a model-ing knife.

8) Using a modeling knife, carefully re-move the covering that overlaps the stabilizermounting platform sides in the fuselage. Re-move the covering from both the top and thebottom of the platform sides.

23


INSTALLING THE VERTICAL STABILIZER.

Hinge.

Remove covering.

Fill epoxy.

Fill epoxy.

2) While holding the vertical stabilizerfirmly in place, use a pen and draw a line oneach side of the vertical stabilizer where itmeets the top of the fuselage.

1) Using a modeling knife, remove thecovering from over the precut hinge slot cutinto the lower rear portion of the fuselage.

90º

VerticalStabilizer.Horizontal

Stabilizer.

3) Slide the vertical stabilizer back inplace. Using a triangle, check to ensure thatthe vertical stabilizer is aligned 90º to the hori-zontal stabilizer.


24

4) Elevator and rudder pushrods assemblyas pictures below.

3) Thread one clevis and M2 lock nut onto each elevator control rod. Thread the hornson until they are flush with the ends of the con-trol rods.

678mm.

Cut.

ELEVATOR - RUDDER PUSHROD HORNINSTALLATION.




4) When you are sure that everything isaligned correctly, mix up a generous amount ofFlash 30 Minute Epoxy. Apply a thin layer to themounting slot and to bottom of the vertical sta-bilizer mounting area. Apply epoxy to the bot-tom and top edges of the filler block and to thelower hinge also. Set the stabilizer in placeand realign. Double check all of your measure-ments once more before the epoxy cures. Holdthe stabilizer in place with T-pins or maskingtape and remove any excess epoxy using apaper towel and rubbing alcohol. Allow the ep-oxy to fully cure before proceeding.

1) Install the elevator control horn usingthe same method as with the aileron controlhorns.

2) Position the elevator control horn onthe both side of elevator.

Epoxy.

Hinge.C/A glue.

25


Elevator pushrod.

Control horn.

M2 lock nut.Metal clevis.

Elevator pushrod.

8mm.8mm.

Pen.

8mm.

RUDDER PUSHROD HORNINSTALLATION.

8mm.

M2 lock nut . M2 clevis.


26



Elevator.

Rudder.

Throttle.

2) Install servos arm to servos. Notice theposition of the servo arms on the servos. Seepicture below.

A.

Elevator pushrod.

A.

C/A glue.

Rudder pushrod.

Elevator pushrod.

A.

C/A glue.

Control horn.

M2 lock nut.

Metal clevis.

Elevator pushrod.

Rudder pushrod.

27


MOUNTING THE NOSE WHEEL.

Locate items necessary to install nosewheel.

1

32

4

5

6

M3x25mm.

M2x12mm.

33

Wheel.

Landing gear.

4

3

3

Wheel.

1 4

M3x25mm. 2

M3x25mm.

70mm.

50mm.

Cut.

2mm.


28

90mm.

4mm.

Screw.

Screw.

Screw.

225mm.

205mm.

Cut.

29


Screw.

1

2

3

214

M3x25mm.


30

INSTALLTION PILOT AND CANOPY.

2

1

3

60mm.

M2x6mm.

4

6

M2x12mm. 5

3

Epoxy.

2) A scale pilot is included with this ARF. TheSeagull Pilot included fitting well to the cockpit.(or you can order others scale pilot figuresmade by Seagull factory. They are available atSeagull distributors.)

If you are going to install a pilot figure, pleaseuse a sanding bar to sand the base of the figureso that it is flat.

1) Locate items necessary to install pilot,cockpit panel, and canopy.

3) Position the pilot figure on the canopy flooras show. Locate the oval shaped on the canopyfloor and remove the covering. Use epoxy toglue this into the base of the pilot figure andglue the cockpit panel in place with C/A glue,please see pictures as shown.

2

Epoxy.

31


1

23

4

1

4

C/A glue.

M2x6mm.

5) Install the canopy and secure it with M2x6mmscrews.

- Apply a bead of canopy glue around the insideedge of the canopy. Position the canopy ontothe hatch. Use tape to hold the canopy secureuntil the glue fully cures.

4) Position the canopy onto the fuselage. Tracearound the canopy and onto the fuselage usinga felt-tipped pen.

13

2

C/A glue.

Cut.

Cut.

4

C/A glue.

5) Install parts on fuselage.


32

Wing bolt.

INSTALLING THE BATTERY-RECEIVER.

Receiver.

ATTACHMENT WING-FUSELAGE.

Battery.

Wing tube.

APPLY THE DECALS.

1) If all the decals are precut and ready tostick. Please be certain the model is clean andfree from oily fingerprints and dust. Positiondecal on the model where desired, using thephotos on the box and aid in their location.

2) If all the decals are not precut, please usescissors or a sharp hobby knife to cut thedecals from the sheet. Please be certain themodel is clean and free from oily fingerprintsand dust. Position decal on the model wheredesired, using the photos on the box and aidin their location.

1) Plug the five servo leads and the switchlead into the receiver. Plug the battery packlead into the switch also.

3) Route the antenna in the antenna tubeinside the fuselage and secure it to the bottomof fuselage using a plastic tape.

2) Wrap the receiver and battery pack inthe protective foam rubber to protect themfrom vibration.

Insert two wing panels as pictures below.

Attach the aluminium tube into fuselage.Screw.

33


3) Turn the airplane upside down. Placeyour fingers on the masking tape and carefullylift the plane .

2) Mount the wing to the fuselage. Using acouple of pieces of masking tape, place themon the top side of the wing 88 mm back fromthe leading edge of the wing at the wing root.

BALANCING.

1) It is critical that your airplane bebalanced correctly. Improper balance willcause your plane to lose control and crash.THE CENTER OF GRAVITY IS LOCATED88 MM BACK FROM THE LEADING EDGEOF THE WING AT THE WING ROOT.

*If possible, first attempt to balance the modelby changing the position of the receiver batteryand receiver. If you are unable to obtain goodbalance by doing so, then it will be necessaryto add weight to the nose or tail to achieve theproper balance point.

With the wing attached to the fuselage, allparts of the model installed ( ready to fly), andempty fuel tanks, hold the model at themarked balance point with the stabilizer level.

Lift the model. If the tail drops when you lift,the model is “tail heavy” and you must addweigh* to the nose. If the nose drops, it is “noseheavy” and you must add weight* to the tail tobalance.

Accurately mark the balance point on the topof the wing on both sides of the fuselage. Thebalance point is located 88 mm back from theleading edge of the wing at the wing root. Thisis the balance point at which your modelshould balance for your first flights. Later, youmay wish to experiment by shifting the balanceup to 10mm forward or back to change theflying characteristics. Moving the balanceforward may improve the smoothness andarrow- like tracking, but it may then requiremore speed for take off and make it moredifficult to slow down for landing. Moving thebalance aft makes the model more agile witha lighter and snappier ”feel”. In any case,pleasestart at the location we recommend .

CONTROL THROWS.

Ailerons: 15mm up 20mm down.

Elevator: 15mm up. 20mm down.

Rudder: 25mm left. 40mm right.

88mm.


34

7) Check the receiver antenna. It shouldbe fully extended and not coiled up inside thefuselage.

3) Double check the balance of the air-plane. Do this with the fuel tank empty.

4) Check the control surfaces. All shouldmove in the correct direction and not bind inany way.

5) If your radio transmitter is equippedwith dual rate switches double check that theyare on the low rate setting for your first fewflights.

2) Check every bolt and every glue jointin the SUPER TUCANO to ensure that everything is tight and well bonded.

6) Check to ensure the control surfacesare moving the proper amount for both lowand high rate settings.

1) Completely charge your transmitterand receiver batteries before your first day offlying.

8) Properly balance the propeller. An outof balance propeller will cause excessive vi-bration which could lead to engine and/or air-frame failure.

We wish you many safe and enjoyableflights with your SUPER TUCANO.

PREFLIGHT CHECK.

D) Check the throttle. Moving thethrottle stick forward should open the carbu-retor barrel. If it does not, flip the servo re-versing switch on your transmitter to changethe direction.

E) From behind the airplane, look atthe aileron on the right wing half. Move theaileron stick to the right. The right aileronshould move up and the other aileron shouldmove down. If it does not, flip the servo re-versing switch on your transmitter to changethe direction.

C) Check the rudder. Looking frombehind the airplane, move the rudder stick tothe right. The rudder should move to the right.If it does not, flip the servo reversing switch onyour transmitter to change the direction.

A) Plug in your radio system per themanufacturer's instructions and turn every-thing on.

B) Check the elevator first. Pull backon the elevator stick. The elevator halvesshould move up. If it they do not, flip the servoreversing switch on your transmitter to changethe direction.

Check the operation and direction of theelevator, rudder, ailerons and throttle.

FLIGHT PREPARATION.

Documents

MS:124 ASSEMBLY MANUAL · 2018. 7. 15. · MS:124 “Graphics and specifications may change without notice”. ASSEMBLY MANUAL Specifications: Wing span -----65in (165cm). Wing area