MRC Bearing Engineering Handbook

MRC Bearing Services

MRC Bearing ServicesCall Toll Free1 (800) MRC-7000

Headquarters1510 Gehman RoadKulpsville, PA 19443USA

MRC is a registered trademark of SKF USA Inc. The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless prior written permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of use of the information contained herein. 2005 SKF USA Inc. Publication M190-730 (7.5M/CW 6/2005) Fifth Edition Version 6/2005 Printed in U.S.A.

Engineering HandbookEngineering Handbook

Engineering Handbook

1

Section I IntroductionMRC History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Catalog and speed rating disclaimer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Warranty statement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Identification system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Bearing symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Identification of non-standard variants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Descriptive manufacturing suffixes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Telephone and fax numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Section II Bearing Specification TablesMRC Bearing Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Bearing Types Summary Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Single-row deep groove, type S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41Single-row deep groove cartridge type SFFC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51Single-row deep groove, type S hybrid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Single-row maximum capacity, filling notch, type M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57Self-aligning ball bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65Double-row angular contact, 5000 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83Single-row 15 angular contact, type R . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103Single-row 15 angular contact, type XLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114Single-row 29 angular contact, 7000 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121Single-row 40 angular contact, 7000 P series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135Single-row 40 angular contact, 7000 PJ series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147PumPac 8000, 8000 BB and 8000 AAB series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157Single-row 29 angular contact, split ring, 9000 U series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167Single-row 40 angular contact, split ring, 9000 UP series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171Duplex 29 angular contact 97000 U series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177Duplex 40 angular contact 97000UP series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180Precision ABEC-5 and ABEC-7 bearings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187

Single-row 15 angular contact, type R . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188Single-row deep groove, type S, Woodworking Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196Ball screw support bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197Excello bearings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199

Specialty bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203Adapter type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204Conveyor roll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205Dynamometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207Electric motor quality / ABMA cross reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209Felt seal replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224Mast guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228Wide inner ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231

Table of Contents Page

Introduction

BEARINGSPECIFICATION TABLESINTRODUCTION ENGINEERING DATA MARATHON SERIES MADE-TO-ORDER


2

Section III Engineering DataDuplex bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234

97000 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237ABEC tolerances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239Shaft and housing fits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245Internal radial clearance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270Dynamic and static load ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271Bearing life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272Speed factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273Speed ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274Materials and limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281Vibration data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299Snap ring data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321Locknuts and lockwashers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325Locknut torque and clamping force . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328Installation procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329Shaft and housing shoulder diameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336Bearing weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340Millimeter-inch equivalents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342Fraction-decimal equivalents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344Conversion factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345Useful formulae. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 348Product index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371

Section IV Marathon Corrosion-Resistant Housings and Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . 385

Section V Made-To-Order Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 389


Engineering Handbook

3

Section I Bearing Symbols

Non-Standard Variants

Section II Single-Row Deep Groove, Type S

Single-Row Maximum Capacity, Filling Notch, Type M

Self-Aligning Ball Bearings

Double-Row Angular Contact, 5000 Series

Single-Row 15 Angular Contact, Type R

Single-Row Angular Contact, 7000, 7000P and 7000PJ Series

PumPac 8000, 8000BB and 8000AAB Series

Single-Row Angular Contact, Split Ring, 9000U, 9000UP, 97000U and 97000UP Series

Precision ABEC-5 and ABEC-7 Bearings

Specialty Bearings

Section III Duplex Bearings

ABEC Tolerances

Shaft and Housing Fits

Lubrication

Vibration Data

Section IV Marathon Corrosion-Resistant Housings and Bearings

Section V Made-To-Order Program

Section IIntroduction

MRC History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Catalog and speed rating disclaimer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Warranty statement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Identification system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Bearing symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Identification of non-standard variants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Descriptive manufacturing suffixes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Telephone and fax numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31


5

MRC Bearing ServicesMRC History

6

The Historical Perspective of MRC Bearing ServicesMRC Bearing Services is the outgrowth of three ofAmericas oldest bearing companiesStandard Roller Bearing Company, Gurney Ball BearingCompany, and Strom Bearing Company.

The Standard Roller Bearing Company was formedwhen a Philadelphia industrialist, S. S. Eveland, mergedthe Ball Bearing Company of Boston with seven othermajor ball bearing and ball-making equipmentmanufacturers. The company used the SRB Diamondtrademark. SRB made many contributions to theadvancement of anti-friction bearings; most notably, thedevelopment of 52100 steel, a high carbon, highchrome alloy steel that greatly improved bearing life.

In 1902, Frederick W. Gurney started the manufacture of ball bearing machinery in Jamestown, New York. He originated the Gurney radial-thrust angular-contactbearing (todays 7000 Series) in 1905, and the Gurneyradial-Type R bearing (same designation today) in1909. Gurney also developed duplex bearingsamatched pair of counterbored bearingswhich were amajor contribution to the accuracy of high speedmachine tool spindles.

Stephen Snyder began manufacturing filling slot radialball bearings in a small Chicago shop in 1908. Hisbusiness was incorporated in 1909 as the U.S. BallBearing Manufacturing Company. Axel Strom becamesole owner and changed the name to Strom BallBearing Manufacturing Company. The companyestablished itself as a major supplier of precision ballbearings to the automotive and machinery industries. A major innovation by Strom was engineering service,provided to customers, to aid in proper choice of ballbearings, their use, and guidance for mounting andmaintenance.

Prior to World War I, Albert F. Rockwell, one of twobrothers who founded New Departure Company,formed the Rockwell-Drake Corporation to manufactureball bearings in Plainville, Connecticut. During the war,Rockwell combined Rockwell-Drake Corporation withseveral other corporations including the Standard RollerBearing Company of Philadelphia.

After World War I, some of the manufacturing units wereliquidated and the company was reorganized asStandard Steel and Bearing, Inc., Division of MarlinRockwell Corporation. In 1923, the bearing

manufacturing plants were consolidated at Plainville,Connecticut. The following year, Gurney Ball BearingCompany merged with Marlin Rockwell Corporation.MRC purchased Strom Ball Bearing ManufacturingCorporation in 1925 and its assets were moved toJamestown, New York, in 1931.

The manufacturing experience, technical background,and managerial skills of these antecedent companiesprovided Marlin Rockwell with a firm base out of whichto develop and grow. In 1953, a new state-of-the-artplant was built at Falconer, New York, and an additionto the plant was completed in 1966. The plant wasdevoted to the manufacture of high-precision ball androller bearings.

In 1964, Marlin Rockwell Corporation was merged with TRW, Incorporated, and renamed TRW BearingsDivision in 1979. With the technological backgroundand facilities of the parent company at its disposal,TRW Bearings Division entered a new period of growth.A ball manufacturing plant was acquired in 1964 atWinstead, Connecticut. In 1976, the Division built a newfacility at Gainesville, Georgia, to specialize in high-volume bearing production.

In 1986, the Bearing Division was acquired by the SKF Group, which is an international manufacturing andmarketing organization composing approximately 200companies with 85 factories, together operating in morethan 130 countries. SKF sales units are backed up bynearly 200 sales offices and over 10,000 distributors anretailers.

Shortly after the consolidation of major executive andmanagement functions at the Jamestown, New Yorkfacilities in the early 1930s, the need for a functionwithin the organization to identify and meet the specialneeds of our bearing distributor customers wasrecognized. To provide these services, the forerunner oftodays MRC Bearing Services was initiated. From theinception of MRC Bearing Services, the list of servicesprovided to our customers and the quality of theservices continued to increase. As the result of over 50years of experience servicing bearing distributorcustomers, MRC Bearing Services now provides animpressive list of services designed to help our bearingdistributor customers respond to the needs of theaftermarket.

Catalog and Speed RatingDisclaimer and Warranty

7

Disclaimer

The contents of this catalog are the copyright ofthe publishers and may not be reproduced (evenextracts) unless permission is granted. Every carehas been taken to insure the accuracy of theinformation contained in this catalog but noliability can be accepted for any errors oromissions.

Listing in this catalog does not necessarily implyproduct availability. Cage type speed adjustmentfactor footnotes does not mean that particularcage variants are available.

The designs and load ratings shown in thiscatalog are those being used at the time ofpublication. The possibility exists that the designs and ratings may be changed to reflectproduct improvement or may be procured from a different company facility. To determine current conditions, contact MRC Bearing Services Product Engineering.

Interchange Information

Interchanges provided in this catalog can provide afast conversion of manufacturer numbers to MRCequivalents. Please note that interchanges are madeon an application basis and may not be completelyidentical to MRC Bearing Services products. Basicinterchanges indicate overall compatible design. Theinterchange information was compiled using dataavailable at the time of publication; however, SKFUSA Inc. and MRC Bearing Services assume noresponsibility or liability for errors or omissions. Also,bearing illustrations depict closure grooves; however,actual bearings may or may not have closuregrooves.

Warranty

MRC Bearing Services warrants that products soldby it shall be free from defects in material andworkmanship. MRC Bearing Services obligationunder this warranty is expressly limited to furnishingwithout additional charge a replacement, or at itsoption, repairing or issuing credit for any productwhich shall within one year from the date of sale bereturned freight prepaid to the plant designated byan MRC Bearing Services representative and whichupon inspection is determined by MRC BearingServices to be defective in materials orworkmanship. Complete information as to service,mounting and relubrication should accompany anyproduct returned for inspection. The provisions ofthis warranty shall not apply to any MRC BearingServices product which has been subjected tomisuse, improper mounting, assembly or lubrication;or which has been repaired or altered if such repairor alteration in the judgement o MRC BearingServices would adversely affect performance of theproduct.

This warranty is in lieu of all other warranties,expressed or implied, including any limitedwarranty of merchantability or fitness for aparticular purpose and is also in lieu of all otherobligations or liabilities on the part of MRCBearing Services, including any obligation orliability arising from contract, tort or otherwise for damages and in no event shall seller be liablehereunder or otherwise for loss of profits;special, incidental, or consequential damages ofany kind. There are no warranties, expressed orimplied, made by MRC Bearing Services, exceptthe warranty against defects in material andworkmanship set forth above. MRC BearingServices and SKF USA Inc. neither assume norauthorize any other person or firm to assume forit any other obligation or liability in connectionwith its products.


8

METRIC RADIAL BEARINGS

TYPE PREFIXF ONE SHIELD, NON-STANDARD

LOCATIONG SNAP RING, NON-STANDARD

LOCATIONZ ONE SEAL, NON-STANDARD

LOCATION

BORE DIAMETER04 AND UP, MULTIPLY LAST TWO NUMBERSBY 5 TO OBTAIN BORE DIAMETER IN MM

CODE DIAMETER00 1001 1202 1503 1704 20

ACCESSORIESF ONE SHIELDFF TWO SHIELDSFP ONE RUBBER COATED

SHIELDFFP TWO RUBBER COATED

SHIELDSG SNAP RING

RSI SEAL FOR SELF-ALIGNINGBEARING

Z ONE SEALZZ TWO SEALS

EXAMPLE OF MARKING ON BEARING BOX

BEARING IDENTIFICATION CODE

R07203SZZ-0001STEEL/C3/ABEC-1

0001 = MRC INTERNAL SUFFIX CODER07 = DATE CODE

SERIES1800 THIN SECTION1900 EXTREMELY LIGHT100K EXTRA LIGHT200 LIGHT300 MEDIUM400 HEAVY

1200 SELF-ALIGNING1300 SELF-ALIGNING1400 SELF-ALIGNING2200 SELF-ALIGNING2300 SELF-ALIGNING

11000 SELF-ALIGNING, EXTENDED INNER

TYPE - SUFFIXM MAXIMUM CAPACITY,

FILLING NOTCHS CONRAD DEEP GROOVE

SWI CONRAD DEEP GROOVE, WIDE INNER RING

WI MAXIMUM CAPACITY,WIDE INNER RING

ADDITIONAL FEATURESC CARTRIDGE WIDTH BEARINGK TAPERED BORE SELF-ALIGNING

BEARINGX TAPERED BORE

HYB#1 CERAMIC ROLLING ELEMENTSABEC-1 TOLERANCES

METRIC ANGULAR CONTACT BEARINGS

SERIES1900 EXTREMELY LIGHT100K EXTRA LIGHT200 LIGHT300 MEDIUM400 HEAVY

5200 DOUBLE-ROW, LIGHT5300 DOUBLE-ROW, MEDIUM5400 DOUBLE-ROW, HEAVY7100K ANGULAR CONTACT, EXTRA LIGHT7200 ANGULAR CONTACT, LIGHT7300 ANGULAR CONTACT, MEDIUM7400 ANGULAR CONTACT, HEAVY8000 PUMPAC9200 ANGULAR CONTACT, SPLIT RING, LIGHT9300 ANGULAR CONTACT, SPLIT RING,

MEDIUM97200 7200/9200 MATCHED SET, LIGHT97300 7300/9300 MATCHED SET, MEDIUM

TYPEBB PUMPAC DIAMONDC DOUBLE-ROW, CONRADM DOUBLE-ROW, MAXIMUM CAPACITYP 40 CONTACT ANGLE,

COUNTERBORED OUTERPJ 40 CONTACT ANGLE, COUNTER-

BORED INNER AND OUTERR 15 CONTACT ANGLE, COUNTER-

BORED OUTERSB DOUBLE-ROW, CONRAD

SBK DOUBLE-ROW, CONRAD WITH CLOSURES

U 29 CONTACT ANGLE, SPLIT RINGUP 40 CONTACT ANGLE, SPLIT RINGU2 MATCHED SET OF7000 DT/9000 UDT

29 CONTACT ANGLEUP2 MATCHED SET OF 7000 PDT/9000

UPDT, 40 CONTACT ANGLE

EXAMPLE OF MARKING ON BEARING BOX

BEARING IDENTIFICATION CODE

R077308 PJDU - H501PRESSED BRASS/ABEC-3

H501 = MRC INTERNAL SUFFIX CODER07 = DATE CODE

ACCESSORIESF ONE SHIELDFF TWO SHIELDSZ ONE SEALZZ TWO SEALS

BORE DIAMETER04 AND UP, MULTIPLY LAST TWONUMBERS BY 5 TO OBTAIN BOREDIAMETER IN MM

CODE DIAMETER00 1001 1202 1503 1704 20

DUPLEX EXECUTIONDB PAIR, BACK-TO-BACK MOUNTINGDE 1/2 PAIR WITH END PLAYDF PAIR, FACE-TO-FACE MOUNTINGDS 1/2 PAIR WITH PRELOADDT PAIR, TANDEM MOUNTINGDU 1/2 PAIR, FLUSH GROUND

Identification System for MRC Bearings

73 08 PJ

2 03 S ZZ

DU

Bearing Symbols

9

IllustrationPrefix Suffix Description Example

AN

B

BC

BIC

ADouble-row, angular contact, non-filling notch ball bearing with cast bronze finger type cage, inwardlyconvergent contact angles, non-rigid design.

A triplex set of PumPac bearings. Two 40 contactangle bearings in tandem mounting matched back-to-backwith one 15 contact angle bearing. V etchedon O.D.

Double-row angular contact, non-filling notch ballbearing, with outwardly convergent contact angles, rigid design and heavy duty cage.

Two PumPac A Bearings in tandem

Double-row angular contact, non-filling notch ballbearing, with cast iron bronze finger type cage, narrowwidth, inwardly convergent contact angles, non-rigid design.

Lock nut.

Double-row, angular contact, non-filling notch ball bearing, with cast bronze finger type cage, andinwardly convergent contact angles, non-rigid design.

Torque tube type airframe bearing.

Thrust ball bearing with grooved races.

Outwardly convergent contact angle when used with5000 Series filling notch bearings. Rigid design.

Single-row, metric, high speed rotor ball bearing.

PumPac Diamond. Matched set of 15 contact anglebearings in back-to-back mounting. V etched on O.D. to form a diamond.

Bell crank type airframe bearing.

ABMA designation, non-filling notch, inch size, various configurations.

5210A

8309AAB

5308AC

5210AH

AN15

5210AS

B540

4B

5309B

34B

8309BB

BC4W10

18BIC4800

AAB

AC

ADT

AH

AS

B

B

B

BB

W

MRC Bearing ServicesBearing Symbols

10


BTK

BWF

CB

CONV

CONV

CONV

CONV

CONV

CONV

Double-row, integral shaft ball bearing, with seal andshield.

Double-row, integral shaft ball bearing, with two seals.

Single-row deep groove type ball bearing, similar to SType.

Thrust ball bearing, single acting, with flat races.

Double-row angular contact, non-filling notch ballbearing, with outwardly convergent contact angles,rigid design.

Conveyor type ball bearing.

Single-row deep groove type ball bearing, with oneshield, similar to SF Type.

Single-row deep groove type ball bearing, with twoshields, similar to SFF Type.

Conveyor bearing, two seals, slotted for bracketmounting.

Double-row conveyor bearing, seal and shield, slottedfor bracket mounting, Rigid design.

Conveyor bearing, two seals, direct roller mounting.

Conveyor bearing, seal and shield, slotted for bracketmounting.

Conveyor bearing, one seal, direct roller mounting.

Conveyor bearing, seal and shield, slotted for bracketmounting.

BTK4800

BWF4800

208C

6C

5310C

CB5043

208CF

208CFF

CONV4A

CONV4E2

CONV4J

CONV4SF

CONV4SZ

CONV3Y2

C

C

C

CF

CFF

A

E

J

SF

SZ

Y

Bearing Symbols

11


DPP

DSP

CT Clutch release bearing, plain.

Clutch release bearing, with housing.

Clutch release bearing, with housing.

Clutch release bearing, with housing and greasefitting.

Single-row deep groove type ball bearing with oneseal, similar to SZ Type.

Single-row deep groove type ball bearing with twoseals, similar to SZZ Type.

A duplex ground half pair matched with a similar halfpair in a DE, DS, DT or DU arrangement.

Matched set of duplex bearings, back-to-backmounting.

Two glass fabric reinforced PTFE (Teflon) seals.

Matched set of duplex bearings, universal mounting,with end play requirement.

Matched set of duplex bearings, face-to-facemounting.

Double-row airframe bearing with two glass reinforcedPTFE (Teflon) seals, non rigid design.

Matched set of duplex bearings, universal mounting,with preload requirement.

Double-row, internally self-aligning, airframe bearing,with two glass reinforced PTFE (Teflon) seals.

211CT

210CTC

211CTQ

209CTR

208CZ

208CZZ

7207D

7207DB

B540DD

7207DE

7207DF

DPP4

7207 DS DL

DSP4

CTC

CTQ

CTR

CZ

CZZ

D

DB

DD

DE

DF

DS

Teflon is a registered trademark of E.I. duPont de Nemours & Co.


12


DW

DW

E

ER

E

FB

FB

FB

DT Matched set of duplex bearings, tandem mounting.

| pair duplex bearings, universal mounting with nopreload or end play.

Double-row airframe bearing with two glass reinforcedPTFE (Teflon) seals, rigid design.

Double-row airframe bearing with cage and two glassreinforced PTFE (Teflon) seals, rigid design.

Single-row magneto type ball bearing with separableouter ring.

Self-aligning ball bearing with higher load rating thanoriginal design.

Power transmission type bearing, extended inner ringwith set screws, with snap ring and relube holes inouter ring.

Single-row, counterbored outer ring, radial type ballbearing.

Single-row elevator type bearing with groove in outerring and two shields.

Thrust bearing, single acting.

One shield.

Single-row flanged ball bearing with tapered O.D.

Single-row flanged ball bearing with tapered O.D. andtwo removable shields.

Single-row flanged ball bearing with tapered O.D. andtwo rubber beaded shields.

7207 DT

7207 DU

DW4

DW4K

E16

2205E

ER16

E16R1

203ES

1115F

207SF

FB3

FB3FFM

FB3FFP

DU

K

E

R

ES

F

F

FFM

FFP


Bearing Symbols

13


FB

FC

FC

FC

FC

FG

FG

ZZ Single-row flanged ball bearing with tapered O.D. andtwo seals.

Single-row flanged ball bearing with cylindrical O.D.

Single-row flanged ball bearing with cylindrical O.D.and two removable shields.

Single-row flanged ball bearing with cylindrical O.D.and two rubber beaded shields.

Single-row flanged ball bearing with cylindrical O.D.and two seals.

Two shields.

Single-row, inch size, cartridge width bearing with twoshields.

Two removable shields.

Single-row, inch size, cartridge width bearing with tworemovable shields

Two rubber coated shields.

Two felt seals, replaced by 88XXX.

Two felt seals and snap ring, replaced by 488XXX.

Single-row maximum capacity ball bearing with shieldon same side as filling notch and snap ring on opposite side.

Single-row counterbored outer ring ball bearing withshield and snap ring on side opposite counterbore.

FB3ZZ

FC3

FC3FFM

FC3FFP

FC3ZZ

207SFF

R4FFC

R4FFM

R4FFMC

R4FFP

203FFS

203FFSG

FG309M

FG209R

FFM

FFP

ZZ

FF

FFC

FFM

FFMC

FFP

FFS

FFSG

M

R


14


F

F

F

F

FZG

FZ

FM One removable shield.

Single-row maximum capacity ball bearing with shield on same side as filling notch.

Single-row maximum capacity ball bearing with shieldand snap ring on same side as filling notch.

One rubber coated shield.

Single-row counterbored outer ring ball bearing withshield on side opposite counterbore.

Single-row counterbored outer ring ball bearing withsnap ring on counterbore side and shield on oppositeside.

One felt seal, replaced by 8XXX.

One felt seal and one shield, replaced by 87XXX.

One felt seal and one shield with snap ring on seal side.

One felt seal with snap ring on open side of bearing.

Front wheel bearing.

One seal and one shield.

Single-row maximum capacity ball bearing with sealon filling notch side and shield and snap ring onopposite side.

Single-row maximum capacity ball bearing with sealon filling notch side and shield on opposite side.

R4FM

F309M

F309MG

R4FP

F209R

F209RG

203FS

203FSF

203FSFG

209FSG

41FW

207SFZ

FZG209M

FZ209M

M

MG

FP

R

RG

FS

FSF

FSFG

FSG

FW

FZ

M

M

Bearing Symbols

15


FZ

G

G

G

G

G

GR

G

G

G

GT

H

MGSingle-row maximum capacity ball bearing with sealand snap ring on filling notch side and shield onopposite side.

Snap ring.

One felt seal with snap ring on same side as seal.

One felt seal and one shield with snap ring on shieldside, replaced by 487xxx, .

Single-row maximum capacity ball bearing with shieldand snap ring on side opposite filling notch.

Single-row maximum capacity ball bearing with shieldon filling notch side and seal and snap ring onopposite side.

Pressed flange housing, regreaseable, eccentriclocking collar.

Pillow block, regreaseable, with two Flexigard seals,eccentric locking collar.

Single-row counterbored outer ring ball bearing withsnap ring on side opposite counterbore. 15 contractangle.

Single-row counterbored outer ring ball bearing withshield on counterbore side and snap ring on oppositeside. 15 contact angle.

Single-row deep groove ball bearing with shield andsnap ring on same side.

Pillow block, regreaseable, with two seals, eccentriclocking collar.

Adapter sleeve, nut and lockwasher assembly used with self-aligning ball bearing with tapered bore.

9000 Series angular contact ball bearing with split outer ring

FZ209MG

208SG

G209FS

G209FSF

G207MF

G207MFZ

G62MS3

GR2

G209R

G209RF

G208SF

GT1|

H322

9310H

G

FS

FSF

MF

MFZ

MS

R

RF

SF

H


16


HH

J

J

K

KP

KP

KP

KP

KP

KP

Combined glass reinforced PTFE (Teflon) seal andstainless steel shield.

Ball screw support, duplex pair, face-to-face mounting.

Ball screw support, quadruplex set, tandem pairmatched face-to-face with a tandem pair.

Single-row, counterbored outer ring, radial type bearing, reduced O.D. and narrow width. 15 contactangle.

Double-row angular contact, filling notch type bearing,standard width and inwardly converging contact angles, non-rigid design.

Self-aligning ball bearing with 1:12 tapered bore.

Single-row airframe type bearing with two stainlesssteel shields.

Single-row airframe type bearing with two glassreinforced PTFE (Teflon) seals.

Single-row airframe type bearing with two glassreinforced PTFE (Teflon) seals, similar to KP Typeexcept reduced O.D. and width.

Single-row airframe type bearing with two glassreinforced PTFE (Teflon) seals, and cage, same asKP-A except includes cage.

Single-row airframe type bearing with two glassreinforced PTFE (Teflon) seals.

Single-row airframe type bearing with two glassreinforced PTFE (Teflon) seals, and self-aligning ring in O.D.

Single-row airframe type bearing with two glassreinforced PTFE (Teflon) seals, and cage.

Single-row, counterbored outer ring, radial type, ballbearing. 15 contact angle.

HH-KSP8

J150DF

J150DFDT

114JR

5210K

1215K

K3L

KP3

KP3A

KP3AK

KP16B

KP16BS

KP4K

104KR

DF

DFDT

JR

K

K

L

A

AK

B

BS

K

KR


Bearing Symbols

17


KSP

KSP

KSP

L

LB

LL

LZ

M

M

KS Single-row deep groove type ball bearing.

Single-row, extra precision, separable inner ring, radial type bearing.

Single-row, extra precision, low shoulder one side ofinner, non-separable, radial type bearing.

Single-row, airframe type bearing, internally self-aligning, with two glass reinforced PTFE (Teflon)seals.

Single-row, airframe type bearing, internally self-aligning, with two glass reinforced PTFE (Teflon)seals. Similar to KSP except reduced O.D. and width.

Single-row airframe type bearing, internally self-aligning, with two glass reinforced PTFE (Teflon)seals. Similar to KSP except reduced O.D. and width.

One glass reinforced PTFE (Teflon) seal.

Flange unit, non-regreaseable, with two labyrinthseals, and eccentric locking collar.

Two glass reinforced PTFE (Teflon) seals.

Flange unit, non-regreaseable, with two seals andeccentric locking collars.

Airframe bearing with special close tolerances.

Single-row, miniature, inch size bearing, ABEC-5precision.

Single-row, maximum capacity, filling notch type ballbearing.

Double-row angular contact, filling notch ball bearingwith outwardly convergent contact angles.

104KS

106KSB

106KSJ

KSP4

KSP4A

KSP3L

L105KS

LB1

LL105KS

LZ2

MKP16B

M0620

208M

5210M

KSB

KSJ

A

L

M

M



18


MR

MR

MR

MR

MR

MR

MR

MR

MR

N

M Machined bronze cage for self-aligning ball bearings.

Machined bronze cage and ABMA C2 internalclearance for self-aligning ball bearing.

Single-row maximum capacity, filling notch ballbearing with shield and snap ring on filling notch sideand seal on opposite side.

Cylindrical roller bearing, with two flanges on innerring, none on outer ring.

Cylindrical roller bearing, outer ring only, no flanges.

Cylindrical roller bearing, inner ring, roller and cageassembly only, two flanges on inner ring.

Cylindrical roller bearing, with two flanges on innerring, one on outer ring.

Cylindrical roller bearing, two flanges on outer ring,none on inner ring.

Cylindrical roller bearing, inner ring only, no flanges.

Cylindrical roller bearing, outer ring, roller and cageassembly only, two flanges on outer ring.

Cylindrical roller bearing, two flanges on outer ring,one flange on inner ring, with side plate.

Cylindrical roller bearing, two flanges on outer ring,one flange on inner ring.

Double-row angular contact, filling notch ball bearingwith inwardly convergent contact angles.

Lock nut.

2314M

2315MC2

209MFZG

MR208C

MR208CQ

MR208CY

MR208D

MR208E

MR208EJ

MR208EX

MR208F

MR208G

5210MW

N06

MC2

MFZG

C

CQ

CY

D

E

EJ

EX

F

G

MW

Bearing Symbols

19


O

OR

P

PB

PD

P

PZ

R

N Single-row, maximum capacity, filling notch type ballbearing, narrow width.

Fibreglass reinforced 6/6 polyamide cage.

Single-row, metric, high speed rotor bearing, lessinner ring.

Single-row, inch size, high speed rotor bearing, lessinner ring.

Single-row airframe type bearing, two seals, aircraftpulley type.

Single-row angular contact, counterbored outer ring,heavy duty bearing, with 40 contact angle.

Pillow block, non-regreaseable, with two labyrinthseals and eccentric locking collar.

A duplex ground half pair, 40 angular contact bearing,counterbored outer ring, matched with a similar halfpair in a DE, DS, DT, or DU arrangement.

Double-row airframe type bearing, two seals, aircraftpulley type, rigid design.

Single-row angular contact, counterbored inner andouter ring, heavy duty bearing, with a 40 contactangle.

A duplex ground half pair, 40 angular contact bearing,counterbored inner and outer rings, matched with asimilar half pair in a DE, DS, DT, or DU arrangement.

Single-row airframe type bearing, with two seals,aircraft pulley type.

Pillow block, non-regreaseable, with two seals andeccentric locking collar.

Single-row, small inch size bearing.

112N

206S-NYL

034B

OR4B

P8

7308P

PB1|

7308PD

PD5K

7308PJ

7308PJD

P5K

PZ2|

R6

NYL

B

B

P

PD

K

PJ

PJD

K


20


R

RA

RA

RA

RA

RAP

R

R

R

R

R

R Single-row, counterbored outer ring, radial typebearing, 15 contact angle.

Double-row, radial type, non-filling notch ball bearingwith cast bronze finger type cage. 0 contact angles.

Single-row, small inch size bearing, with increasedO.D. and width.

Power transmission type, inner extended one sideonly, cylindrical O.D., two flexigard seals, non-regreaseable, eccentric locking collar.

Power transmission type, inner extended one sideonly, cylindrical O.D., two seals, non-regreaseable,eccentric locking collar.

Power transmission type, inner ring extended one sideonly, spherical O.D., two Flexigard seals, non-regreaseable, eccentric locking collar.

Power transmission type, inner ring extended one sideonly, spherical O.D., two seals, non-regreaseable,eccentric locking collar.

Airframe bearing, rod end type, with male threadedshank.

Single-row, small inch size, high speed rotor bearing,with separable inner ring.

Cylindrical roller bearing, with two flanges on innerring, none on outer ring.

Cylindrical roller bearing, outer ring only, no flanges.

Cylindrical roller bearing, inner ring, roller and cageassembly only, two flanges on inner ring.

Cylindrical roller bearing, with two flanges on innerring, one on outer ring.

Single-row, counterbored outer ring, radial typebearing, with controlled relationship of ring faces,used in duplex sets.

207R

5306R

R4A

RA008ATT

RA008AZZ

RA008BTT

RA008BZZ

RAP3M

R3B

R208C

R208CQ

R208CY

R208D

306RD

R

A

ATT

AZZ

BTT

BZZ

M

B

C

CQ

CY

D

RD

Bearing Symbols

21


R

R

R

REPB

REP

REP

REP

REP

R

R

RDM Dynamometer bearing, ABEC-5 inner ring, ABEC-1outer ring, phenolic cage, 15 contact angle.

Single-row, split inner ring bearing, 20 contact angle.

Cylindrical roller bearing, two flanges on outer ring,none on inner ring.

Cylindrical roller bearing, inner ring only, no flanges.

Cylindrical roller bearing, outer ring, roller and cageassembly only, two flanges on outer ring.

Airframe bearing, rod end type, with female threadedshank.

Airframe bearing, rod end type, with female threadedshank.

Airframe bearing, rod end type, with hollow shank.

Airframe bearing, rod end type, with male threadedshank.

Airframe bearing, rod end type, with solid shank.

Cylindrical roller bearing, two flanges on outer ring,one flange on inner ring, with side plate.

Single-row, counterbored outer ring, radial typebearing, with shield on counterbored side, 15 contactangle.

Single-row, counterbored outer ring, radial typebearing, with shield and snap ring on counterboredside, 15 contact angle.

Cylindrical roller bearing, two flanges on outer ring,one flange on inner ring.

316RDM

309RDT1|

R208E

R208EJ

R208EX

REPB3N

REP4F7

REP3H5

REP4M6

REP4S10

R208F

208RF

208RFG

R208G

RDT

E

EJ

EX

N

F

H

M

S

F

RF

RFG

G


22


RRA

RRA

RT

RW

RGSingle-row, counterbored outer ring, radial typebearing, with snap ring on counterbored side, 15contact angle.

Single-row, counterbored inner and outer rings, extraprecision, radial type bearing, 15 contact angle.

Power transmission bearing, inner ring extended oneside only, spherical O.D., two Flexigard seals,regreaseable, eccentric locking collar.

Power transmission bearing, inner ring extended oneside only, spherical O.D., two seals, regreaseable,eccentric locking collar.

Double-row, radial type, non-filling notch ball bearing,with cast bronze finger type cage.

Self-aligning ball bearing with two synthetic rubberseals.

Power transmission bearing, inner ring extended bothsides, two seals, regreaseable, eccentric lockingcollar.

Single-row deep groove, rear wheel type bearing withtwo seals.

Single-row, counterbored outer ring, radial typebearing, with seal on counterbored side, 15 contactangle.

Double-row, split outer ring, radial type bearing.

Single-row deep groove ball bearing.

9000 Series angular contact angle bearing withone-piece inner and outer rings, 20 contact angle.

Double-row, angular contact, non-filling notch bearing,with outwardly convergent contact angles, rigiddesign.

Double-row, angular contact, non-filling notch,standard width bearing, with outwardly convergentcontact angles, rigid design.

208RG

106RJ

RRA008BTT

RRA008BZZ

5312RS

22102RS1

RT107BZZ

RW716

306RZ

5206R2

207S

9212S1

5203SB

5203SBK

RJ

BTT

BZZ

RS

2RS1

RZ

R2

S

S

SB

SBK

Bearing Symbols

23


S

SFFC Single-row deep groove, cartridge width bearing, withtwo shields.

Single-row deep groove, cartridge width bearing, withtwo shields and snap ring.

Single-row deep groove ball bearing with two rubberbeaded shields.

Single-row deep groove ball bearing with rubberbeaded shield.

Single-row deep groove bearing, wider than standard.

Single-row deep groove, cartridge width bearing, withtwo removable shields.

Single-row deep groove, cartridge width bearing, withtwo labyrinth seals.

Single-row, small inch size bearing.

Stainless steel (440C) rings and rolling elements.

Single-row deep groove bearing, narrower thanstandard.

Single-row deep groove bearing, with inner ringextended one side.

Single-row deep groove bearing, tapered bore, withadapter sleeve and nut.

Single-row deep groove bearing, cartridge width, withtwo seals.

Single-row deep groove bearing, cartridge width, withtwo seals and snap ring.

210SFFC

210SFFCG

1910SFFP

1806SFP

105SH

210SLLC

210SRRC

S3S

207SST

209SV

311SWI

210SXY

210SZZC

210SZZCG

SFFCG

SFFP

SFP

SH

SLLC

SRRC

S

ST

SV

SWI

SXY

SZZC

SZZCG


24


T

T

T

T

UR

UT

ARRPower transmission bearing, inner ring extended bothsides, cylindrical O.D., two labyrinth seals, non-regreaseable, eccentric locking collar.

Power transmission bearing, inner ring extended bothsides, cylindrical O.D., two seals, non-regreaseable,eccentric locking collar.

Power transmission bearing, inner ring extended bothsides, spherical O.D., two labyrinth seals, non-regreaseable, eccentric locking collar.

Power transmission bearing, inner ring extended bothsides, spherical O.D., two seals, non-regreaseable,eccentric locking collar.

Two metal shrouded synthetic rubber seals.

Thrust bearing, single acting, with self-aligningwasher.

9000 Series angular contact ball bearing with splitinner ring, 29 contact angle.

9000 Series angular contact ball bearing with splitinner and outer rings, 29 contact angle.

9000 Series, extra light, angular contact ball bearingwith split inner ring, 29 contact angle.

9000 Series, 40 angular contact ball bearing with splitinner ring.

Flange unit, two seals, regreaseable, with eccentriclocking collar.

Flange unit, two Flexigard seals, regreaseable, witheccentric locking collar.

Single-row, maximum capacity, filling notch type ballbearing, with narrow width.

Felt seal replacement bearing with one seal and oneshield with snap ring on seal side.

T1100ARR

T1100AZZ

T1100BRR

T1100BZZ

205STT

1109U

9309U

9213UH

9107UK

9308UP

UR2

UT1|

209V

487508V

AZZ

BRR

BZZ

TT

U

U

UH

UK

UP

V

V

Bearing Symbols

25


W

WC

XLR

XLS

XO

Y

Lock washer.

Cylindrical roller bearing, roller and cage assemblyonly.

Single-row felt seal replacement bearing with innerand outer ring faces flush on one side.

Single-row, maximum capacity, filling notch type ballbearing, with inner ring extended one side only.

Single row maximum capacity ball bearing with innerring extended one side, and shield on extended innerside.

Tapered bore bearing.

Cylindrical roller bearing, inch size.

Single-row, counterbored outer ring, 15 angularcontact ball bearing, inch size.

Excello Replacement Bearing.

Tapered bore bearing with adapter sleeve.

Adapter sleeve and nut.

Duplex pair of airframe bearings, seals on outboardside, aircraft pulley type.

One synthetic rubber seal.

Two synthetic rubber seals.

Single-row, cartridge width bearing, extra small size,with two synthetic rubber seals.

W06

R207W

WC87504

318WI

318WIF

206SX

XLR3|E

XLS2

XO90RBDS

208SXY

6Y

Y96PWID2B

206SZ

206SZZ

38ZZC

W

WI

WIF

X

RBDS

XY

Y

PWI-DB

Z

ZZ

ZZC

MRC Bearing ServicesPrefix/Suffix Symbols for Single-RowBearing Non-Standard Variants

26

PrefixSuffix Illustration

MF

MG

MFG

GM

FM

FMG

GMF

FGM

MX


XM

MXF

XMF

MFX

FMX

MFZ

FZM

MFZG

FZMG


GMFZ

FZGM

MXFZ

XFZM

XMFZ

FZMX

SFG

GSF

SFX

Nomenclature

SSingle Row Deep Groove TypeMSingle Row Filling Notch TypeR15 Angular Contact TypeWIWide Inner Ring Filling Notch TypeSWIWide Inner Ring Non-Filling Notch Type

FShieldZSealGSnap RingFSFelt SealXTapered Bore

When single seal is used, seal symbol (Z) replaces (F)in designations shown except for Filling Notch (M) Type

Prefix/Suffix Symbols for Single-RowBearing Non-Standard Variants

27


SXF

SWIF

FSWI

WIF

FWI

FSG

GFS

FSFG


GFSF

RF

RG

RFG

FR

GR

FGR

GRF


FRG

RX

XR

RFX

XRF

FRX

FXR

Nomenclature

SSingle Row Deep Groove TypeMSingle Row Filling Notch TypeR15 Angular Contact TypeWIWide Inner Ring Filling Notch TypeSWIWide Inner Ring Non-Filling Notch Type

FShieldZSealGSnap RingFSFelt SealXTapered Bore

When single seal is used, seal symbol (Z) replaces (F)in designations shown except for Filling Notch (M) Type

MRC Bearing ServicesPrefix/Suffix Symbols for Double-RowBearing Non-Standard Variants

28


GCFZ

GCZ

GCF

FMZ

FM

ZM


GM

FMG

ZMG

GMF

GMZ

FGM


ZGM

GMFF

GMZZ

FMZG

GMFZ

FGMZ

Nomenclature

MFilling Notch TypeCNon-Filling Notch TypeFShieldZSealGSnap Ring

MRC Manufacturing Suffixes

29

MRC Manufacturing Suffixes

The manufacturing suffix is specified on packinglists, invoices and all unit cartons. Wheneverpossible the manufacturing suffix is also shown onthe bearing steel. It is separated from the standardMRC part number by several spaces. Example:

204SZZ

Standard MRC Part No.

H501

Manufacturing Suffix

A four digit manufacturing suffix is used by MRCinternally to define bearing specifications as well asto track such information as plant-of-manufacture asproduct is distributed throughout the MRCwarehousing network. This suffix is assignedsequentially within the MRC computer system andcan only be cross-referenced internally by the MRCCustomer Service Representative.

The standard MRC part number is sufficient forspecifying customer requirements for all Stock sizes. The use of a non-descriptive manufacturingsuffix permits minor changes to the design andmanufacture of standard product without a confusingnomenclature change. The revised product may stillbe tracked through distribution by the four digitmanufacturing suffix.

MRC Bearing ServicesMRC Descriptive Part Suffixes

30

MRC Descriptive Part SuffixesA Descriptive Part Suffix is frequently combined with the standard MRC Part Number to provide a morecomplete description of Bearing Design Specifications.Descriptive Suffixes are found on MRC Price Sheets,Packing Lists and Invoices. Preload and EndplayDescriptive Suffixes are only displayed on the bearingsteel away from the basic part number.

Descriptive Part Suffixes are physically separatedfrom the standard MRC Part Number by a dash -.

213RDS

Basic Part No.

BKE#7

Descriptive Suffix

-

Descriptive Part Suffix Definitions

BKEBRSBRZCACBCCCXCOC2C3C4DEDLDMDHDXEAHTHYB#1MRB# 3# 5# 7EMQNYLPOSTLTDCTN9T44

Machined Phenolic Composition (Bakelite)Pressed Brass CageMachined Bronze CageLess than Normal End Play Designation for Duplexed BearingsNormal End Play Designation for Duplexed BearingsGreater than Normal End Play Designation for Duplexed BearingsSpecial End Play Designation for Duplexed BearingsABMA #0 Radial Clearance (MRC-ST Fit)ABMA #2 Radial Clearance (MRC-Tl Fit)ABMA #3 Radial Clearance (MRC-LO Fit)ABMA #4 Radial Clearance (MRC-XL Fit)End Play Designation for Duplexed BearingsLight Preload Designation for Duplexed BearingsMedium Preload Designation for Duplexed BearingsHeavy Preload Designation for Duplexed BearingsSpecial Preload Designation for Duplexed BearingsEach, Sold as | Pair (Example: 9218UDT-BRZEA)High Temperature Heat TreatCeramic rolling elements and ABEC-1 TolerancesMachined Brass Cage for Self-Aligning Ball BearingTexaco Premium RB GreaseABEC-3 TolerancesABEC-5 TolerancesABEC-7 TolerancesElectric Motor QualityGlass Fiber Reinforced Polyamide Poly-Oil TreatmentSteel CageThin Dense Chrome PlatedGlass Fiber Reinforced Polyamide CageMRC Code #44 Radial Clearance

The six primary features of the servicesprovided to our customers are listed below:

31

MRC is always one 1-800-MRC-7000 phone callawaysaving time in response to your customer.

Fax number toll-free at 888-322-4672

Immediate attention is given to technical questions byour in-house engineering department, (215) 513-4700.

MRC Technical Services experts are able to addressbearing problems in the field and offer solutions.

MRC provides bearing failure analysis in problemapplications.

Friendly, knowledgeable customer service people are able to take important action on your requests.

Many servicing warehouses assure inventoryaccessibility in all parts of the country.

BEARINGSPECIFICATION TABLESINTRODUCTION ENGINEERING DATA MARATHON SERIES MADE-TO-ORDER

BearingSpecificationTables

Section IIBearing Specification Tables

33

MRC Bearing Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Bearing Types Summary Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Single-row deep groove, type S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41Single-row deep groove cartridge type SFFC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51Single-row deep groove, type S hybrid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Single-row maximum capacity, filling notch, type M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57Self-aligning ball bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65Double-row angular contact, 5000 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83Single-row 15 angular contact, type R . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103Single-row 15 angular contact, type XLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114Single-row 29 angular contact, 7000 series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121Single-row 40 angular contact, 7000 P series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135Single-row 40 angular contact, 7000 PJ series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147PumPac 8000, 8000 BB and 8000 AAB series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157Single-row 29 angular contact, split ring, 9000 U series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167Single-row 40 angular contact, split ring, 9000 UP series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171Duplex 29 angular contact 97000 U series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177Duplex 40 angular contact 97000UP series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180Precision ABEC-5 and ABEC-7 bearings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187

Single-row 15 angular contact, type R . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188Single-row deep groove, type S, Woodworking Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196Ball screw support bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197Excello bearings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199

Specialty bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203Adapter type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204Conveyor roll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205Dynamometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207Electric motor quality / ABMA cross reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209Felt seal replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224Mast guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228Wide inner ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231


MRC Bearing Series

35

The basic types of bearings shown on the followingpages are furnished in several series as illustratedin the sketch. Note that although the bore is thesame, the outside diameter, width and ball size areprogressively larger from thin section to heavy.Reference to the dimensions tables will indicate theseries available for the different types.

36

Bearing Type Cage Contact Performance Characteristics DescriptionAngle Level Speed Radial Axial

Capacity Capacity

Extremely HighVery HighHighModerate










Type S Conrad Pressed 0Deep Groove Steel

R Inch Series Pressed 0Conrad Deep Groove Steel

Type M Maximum Pressed 0Capacity Filling Notch Steel

Type R 15 Pressed 15Angular Contact Steel

5000 Series Pressed 30Double Row SteelC Type Conrad,M TypeMaximumCapacity

7000 Series 29 Pressed 29Angular Contact Steel

7000P Series 40 Machined 40Angular Contact and Pressed

Brass

XLS Inch Series Bakelite 15Angular Contact

5300 UPG Series Machined 40Split Inner Ring BrassDouble Row

8000 PumPac Series Machined 40 & 15Angular Contact BrassAssembly

37

Bearing Types Summary Chart

Description

Ordinarily supplied with loose internal clearance. Outer and inner races have full shoulders. Has equal load-carrying capacity in either direction. Recommended for moderately heavy radial loads, thrust loads in either direction, or combination loads.

Ordinarily supplied with standard internal clearance. Has inch boundary dimensions. Outer and inner races have full shoulders. Has equal load-carrying capacity in either direction. Recommended for moderately heavy radial loads, thrust loads in either direction, or combination loads.

Ordinarily supplied with standard internal clearance. This type has a filling notch on one side of the inner and outer rings to insert a maximum ball complement. Can carry heavy radial load or combined radial and thrust load where the radial load predominates. Not recommended for pure thrust loads or combined loads where thrust load predominates.

Supplied with loose internal clearance for normal applications. Counterbored outer ring to assemble maximum ball complement. Outer ring is heated in order to assemble. Can carry heavy radial load, moderate thrust load in one direction only, or combined loads where thrust load is against the heavy shoulder on the outer ring.

C type ordinarily supplied with loose internal clearance. Has full shoulders and no filling notches. Has outwardly converging contact angles. C type will support heavy radial loads, and equally heavy thrust load in either direction, or heavy combined radial and thrust loads. M type ordinarily supplied with standard internal clearance. Has filling notches on one side only for inserting maximum ball compliment. Has outwardly converging contact angles. M type has heavy radial capacity. Also has moderate thrust capacity in onedirection and can take light thrust load in reversing direction.

Counterbored outer ring, non-separable type. Ordinarily available in single and paired variants. Paired variants typically supplied with line-to-line internal clearance. Others of internal clearance/preloadmay be necessary for special conditions. Two-piece pressed steel cage for normal use or one-piece non-metallicor solid brass cage for high speed, high operating temperature, or severe vibration application. High thrust load in one direction, combined radial and thrust load where thrust load predominates. Should not be used for radial loads only.

Similar in design to the 7000 Series bearing. Thrust capacity is 1.18 to 1.4 times that of the 7000 Series, varies with individual sizes. Restricted to primarily thrust loads. Should not be used for radial loads only or combined radial and thrust loads where radial load predominates.

Counterbored outer ring, non-separable type. Similar to the Type R angular contact except that it has inch dimensions. It also has a relatively light cross section for space constraints. Can carry heavy radial load, moderate thrust load in one direction only, or combined loads where thrust load is against the heavy shoulder on the outer ring.

Designed with two-piece inner ring and one-piece outer ring and snap ring. Differs from the 5000C and M Types because of its 40 contact angle and split inner ring. Also has a machined brass cage and reduced axial clearance. Can carry very heavy thrust loads in either direction or combined loads where the thrust load predominates.

Bearing assembly consists of a 40 and 15 bearing, ABEC-3 precision tolerances, reduced axial clearance, and machined brass cages. Can carry high thrust load in one direction and light reversing thrust load in the opposite direction. The lower contact angle of the back bearing helps prevent ball skidding during periods of no load.

38

Bearing Type Cage Contact Performance Characteristics DescriptionAngle Level Speed Radial Axial

Capacity Capacity











8000BB PumPac Machined 15 & 15Series Angular BrassContact Assembly

8000AAB PumPac Machined 40 & 40Series Angular Brass & 15Contact Assembly

9000U Series Machined 29 or 40Split Inner Ring BrassAngular Contact

97000U2 Series Machined 29Angular Contact BrassAssembly

97000UP2 Series Machined 40Angular Contact BrassAssembly

Marathon Series Polyamide 0

Type DS Phenolic 15 or 25High PrecisionAngular Contact

Type NN3100 Polyamide 0Double RowCylindrical

Type J Phenolic 60Ball ScrewSupport

Type DT Polyamide 60Double Direction or Angular Contact Machined

Brass

39

Bearing Types Summary Chart

Description

Consists of two 15 bearings as opposed to one 40 and one 15, ABEC-3 precision tolerances, reduced axial clearance, and machined brass cages. Can carry predominantly radial load with intermittent thrust load in either direction. Very similar performance to the 7000R series, except that it is a back-to-back pairedarrangement.

Can carry very high thrust loads in one direction and light reversing thrust load in the opposite direction. The pair of 40 A bearings in tandem provides very high thrust capacity in the primary direction,while the 15 B bearing handles any reversing thrust load.

Designed with solid one-piece outer ring and two-piece inner ring, maximum ball compliment and one-piece machined brass cage. Can carry greater thrust in either direction than the Type S. May be used where there is substantial radial load providing there is always sufficient thrust load present. Often paired with another angular contact ball bearing in an assembly.

Paired assembly of a 9000U and a 7000 angular contact bearing. Assembly comes with axial clearance as standard and provides the capacity of a triplex set in the boundary dimensions of a pair. Very heavy thrust loadcapacity because of tandem assembly of 9000U and 7000 bearing in one direction. 9000U supports reversing thrust load in the opposite direction.

Very similar to the 97000U2 series except that it has a 40 contact angle. Because of the higher contact angle,this assembly has the highest thrust carrying capacity for its given boundary dimensions.

Series of corrosion resistant housings and bearings used in heavy wash down and contaminated environments such as food, car wash, gypsum, etc. The unique double sealing arrangement makes Marathon units very effective at keeping out solid and liquid contamination. These units incorporate an insert bearing based on the Type S Conrad bearing so they can handle moderate radial loads and light thrust loads in either direction.However, since they are set screwed to the shaft, the axial load carrying capacity is determined by the holdingpower of the set screws.

ABEC-7 tolerances for machine tool applications that require high speeds and precise running accuracies.Type DS are available in 15 and 25 contact angles. These bearings are normally used in paired arrangements. They function very similarly to the Type R and 7000 series bearings except for the fact that they are much higher precision.

ABEC-7 tolerances for high speeds required by machine tool spindles. Very high radial stiffness because of itsdouble row roller design. Very high radial load carrying capacity. Zero axial load carrying capacity because of the shoulderless outer ring which allows the bearing to expand with shaft thermal growth.

ABEC-7 tolerances for high speed. Counterbored inner and outer ring construction. Very high axial stiffness because of the 60 contact angle and larger quantity of small balls. Usually used in paired, triplex, or quad sets in order to provide adequate stiffness and capacity for the given application conditions. Primarily designed for high thrust loads and very little radial load because of the 60 contact angle.

Type DT has a one-piece outer ring construction with a two-piece inner ring construction. Like the Type J bearing, it has a 60 contact angle. It is also a paired assembly. Its large quantity of small balls also provides high axial stiffness as with the Type J bearings. The Type DT bearing can handle high thrust load in eitherdirection and virtually zero radial load. It is usually paired with a radial type bearing in order to isolate it from any radial loading.

Single-Row Deep GrooveBall Bearings, S-Type

41

The MRC conrad ball bearing is a single-row radialdeep groove bearing with no filling notches. It cancarry significant radial loads, and, because of the uninterrupted raceway grooves and the high degree of conformity between balls and raceways, it cancarry substantial thrust loads in either direction, evenat very high speeds. Single-row deep groove ballbearings are offered open or with single or doubleshields or seals, as well as with snap rings in variouscombinations.

Cage Types and Materials

This type of bearing is supplied with a pressed steelcage as standard; however, for special requirements, it can be supplied with a two-piece riveted machinedcage of phenolic composition or bronze material.

Size

30R1800S1900S100S100KS200S300S400S

Extra SmallSmall Inch-SizeThin SectionExtremely LightNarrow-Type LightExtra LightLightMediumHeavy

424344454647484950

Series Page

Cartridge Type

Equivalent Load and LifeLife Calculation Examples

51

5253

Hybrid Bearings 54

343536

373839

456

789

161919

222226

566

778

.30

.30

.30

.30

.30

.64

459696

110110161

1 4702 2102 210

3 2503 2504 620

600950950

1 3601 3601 960

43 00036 00036 000

36 00036 00028 000

50 00043 00043 000

43 00043 00034 000

30 00026 00026 000

23 00023 00020 000

MRC Bearing Services30 SeriesExtra Small Size

42

These single-row radial conrad-type bearings have 4mm to 9 mm bores (approximately | to |), and aredesigned for very small shafts. They are suitable forhigh speed fractional horsepower motors and smallturbines. MRC offers open, shielded, and sealedtypes. Some sizes are available in stainless steel.30 Series supplied with ABMA CO radial clearanceunless otherwise specified.

MRCBearingNumber

Bore

dmm in

OutsideDiameterDmm in

Width

Bmm in

FilletRadius1)ramm in

ZD2

mm in

DynamicC3)

N lbf

Basic Radial Load Rating Speed Rating2)

StaticC0

N lbf

Open and ShieldedGrease OilRPM RPM

Single andDouble Sealed

GreaseRPM

.1575

.1969

.2362

.2756

.3150

.3543

.6299

.7480

.7480

.8661

.86611.0236

.1969

.2362

.2362

.2756

.2756

.3150

.012

.012

.012

.012

.012

.025

.07

.15

.15

.17

.17

.25

330497497

731731

1 040

135214214

306306441

1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.2) Listed values are for pressed steel or polyamide cage, ABEC-1.

For phenolic composition cage, multiply by 1.66 for grease and 2.00 for oil. For machined bronze cage, multiply by 1.25 for grease and 1.50 for oil. For phenolic compositioncage, ABEC-5 or 7, multiply by 2.30 for grease and 2.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For amore complete explanation, see page 274.

3) Rating for one million revolutions or 500 hours at 33| RPM.

MRCBearingNumber

Bore

dmm in


Shielded orSealedmm in


ZD2

mm in

DynamicC3)

N lbf

Basic Radial Load Rating

StaticC0

N lbf



GreaseRPM

Plain

mm inZD2

mm in

Speed Rating2)

R-2R-2-AR-3

R-4R-4-AR-6

R-8R-10R-12

R-14R-16R-18

R-20R-24

3.23.24.8

6.46.49.5

12.715.919.1

22.225.428.6

31.838.1

9.512.712.7

15.919.122.2

28.634.941.3

47.650.854.0

57.266.7

4.04.44.0

5.05.65.6

6.47.17.9

9.59.59.5

9.511.1

4.04.45.0

5.07.17.1

7.98.7

11.1

12.712.712.7

12.714.3

.30

.30

.30

.30

.41

.41

.41

.79

.79

.79

.79

.79

.79

.79

191939

4571

110

181226361

406406510

613755

312312956

1 4802 8103 320

5 0706 0509 360

10 10010 10012 500

14 00016 800

120120490

6201 1601 340

2 4003 2505 100

5 8506 0007 500

9 30011 800

75 00075 00057 000

44 00039 00031 000

24 00018 00016 000

14 00013 00011 000

11 0009 000

91 00091 00069 000

54 00048 00038 000

29 00022 00019 000

17 00016 00014 000

13 00011 000

52 000 52 00040 000

31 00027 00021 000

16 00013 00011 000

9 6009 0007 900

7 5006 200

.1250

.1250

.1875

.2500

.2500

.3750

.5000

.6250

.7500

.87501.00001.1250

1.25001.5000

.3750

.5000

.5000

.6250

.7500

.8750

1.12501.37501.6250

1.87502.00002.1250

2.25002.6250

.1562

.1719

.1562

.1960

.2188

.2188

.2500

.2812

.3125

.3750

.3750

.3750

.3750

.4375

.1562

.1719

.1960

.1960

.2812

.2812

.3125

.3438

.4375

.5000

.5000

.5000

.5000

.5625

.012

.012

.012

.012

.016

.016

.016

.031

.031

.031

.031

.031

.031

.031

.03

.03

.06

.07

.11

.17

.28

.35

.56

.63

.63

.79

.951.17

7070

215

332632746

1 1401 3602 100

2 2702 2702 810

3 1503 780

2727

110

139261301

540731

1 150

1 3201 3501 690

2 0902 650

R Series Small Inch-Size

43

R series bearings are single-row radial conrad-typebearings that are available in inch sizes for shaftsfrom | to 1| in diameter. Open, shielded, andsealed types are available, and many sizes areavailable in stainless steel.R Series supplied with ABMA CO radial clearanceunless otherwise specified.

1) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.2) Listed values are for pressed steel or polyamide cage, ABEC-1.

For phenolic composition cage, multiply by 1.66 for grease and 2.00 for oil. For machined bronze cage, multiply by 1.25 for grease and 1.50 for oil. For phenolic compositioncage, ABEC-5 or 7, multiply by 2.30 for grease and 2.80 for oil. The speed rating adjustment factors have been determined through historical application and practice. For amore complete explanation, see page 274.

3) Rating for one million revolutions or 500 hours at 33| RPM.

Width B

MRC Bearing Services1800-S Thin Section Series

44

1800-S Series bearings are single-row radial conrad-type bearings that can accommodate light radialloads, two-directional thrust loads, or a combinationof both. They are designed for applications wherespace or weight is very limited.The 1800-S Series is supplied with an ABMA CO Radial internal clearanceunless otherwise specified.

MRCBearingNumber

Bore

dmm in


Width

Bmm in


ZD2

mm in

DynamicC3)

N lbf


StaticC0

N lbf



GreaseRPM

1800S1801S1802S

1803S1804S1805S

1806S1807S1808S

1809S1810S1811S

1812S1813S1814S

1815S1816S1817S

1818S1819S1820S

1821S1822S1824S4)

1826S4)1828S4)1830S4)

1832S4)1834S4)1836S4)

1838S4)1840S4)1844S4)

1848S4)1852S4)1856S4)

1860S4)1864S4)1868S4)

1872S4)1876S4)1880S4)

1884S4)1888S4)1892S4)

1896S4)

101215

172025

303540

455055

606570

758085

9095

100

105110120

130140150

160170180

190200220

240260280

300320340

360380400

420440460

480

192124

263237

424752

586572

788590

95100110

115120125

130140150

165175190

200215225

240250270

300320350

380400420

440480500

520540580

600

555

577

777

779

101010

101013

131313

131616

181820

202222

242424

282833

383838

384646

464656

56

.30

.30

.30

.30

.30

.30

.30

.30

.30

.30

.30

.30

.30

.60

.60

.60

.601.0

1.01.01.0

1.01.01.0

1.01.01.0

1.01.01.0

1.51.51.5

2.02.02.0

2.02.02.0

2.02.02.0

2.02.02.5

2.5

626880

91141184

208233257

315347454

499679741

803864

1 230

1 2801 3301 380

1 4801 9102 060

2 6602 8703 540

3 6904 5504 730

5 6905 9106 370

8 6709 330

11 500

14 20014 70015 900

16 40022 70023 700

24 60025 50033 300

34 700

1 8201 9002 080

2 2503 5104 360

4 4904 7504 940

6 0506 2408 320

8 71011 70012 100

12 50013 00019 500

19 50019 900 20 300

20 80028 10029 100

37 70039 00048 800

49 40061 80062 400

74 10076 10078 000

108 000111 000138 000

172 000172 000178 000

182 000242 000247 000

251 000255 000312 000

325 000

9301 0401 250

1 4602 2402 900

3 4003 8004 150

5 1005 5007 350

8 00011 00011 800

12 90013 70019 600

20 40021 20022 000

23 60030 50032 500

43 00046 50057 000

60 00073 50076 500

91 50095 000

102 000

140 000150 000183 000

228 000236 000255 000

260 000365 000380 000

390 000405 000530 000

560 000

36 000 32 00028 000

24 00019 00017 000

15 00013 00011 000

9 5009 0008 500

7 5007 0006 700

6 3006 0005 300

5 3005 0004 800

4 5004 3003 800

3 6003 4003 000

2 8002 6002 400

2 2002 2001 900

1 8001 7001 600

1 4001 3001 200

1 1001 0001 000

950900900

850

43 00038 00034 000

30 00024 00020 000

18 00016 00014 000

12 00011 00010 000

9 0008 5008 000

7 5007 0006 300

6 3006 0005 600

5 3005 0004 500

4 3004 0003 600

3 4003 2003 000

2 8002 8002 400

2 2002 0001 900

1 7001 6001 500

1 4001 3001 300

1 2001 1001 100

1 000

20 00019 00017 000

16 00013 00011 000

9 5008 0007 500

6 7006 0005 180

4 8004 5004 300

4 0003 6003 400

3 2003 0003 000

2 8002 6002 400

2 2002 000

.3937

.4724

.5906

.6693

.7874

.9843

1.18111.37801.5748

1.77171.96852.1654

2.36222.55912.7559

2.95283.14963.3465

3.54333.74023.9370

4.13394.33074.7244

5.11815.51185.9055

6.29926.69297.0866

7.48037.87408.6614

9.448810.236211.0236

11.811012.598413.3858

14.173214.960615.7480

16.535417.322818.1102

18.8976

.7480

.8268

.9449

1.02361.25981.4567

1.65351.85042.0472

2.28352.55912.8346

3.07093.34653.5433

3.74023.93704.3307

4.52764.72444.9213

5.11815.51185.9055

6.49616.88987.4803

7.87408.46468.8583

9.44889.8425

10.6299

11.811012.598413.7795

14.960615.748016.5354

17.322818.897619.6850

20.472421.259822.8346

23.6220

.1969

.1969

.1969

.1969

.2756

.2756

.2756

.2756

.2756

.2756

.2756

.3543

.3937

.3937

.3937

.3937

.3937

.5118

.5118

.5118

.5118

.5118

.6299

.6299

.7087

.7087

.7874

.7874

.8661

.8661

.9449

.9449

.9449

1.10241.10241.2992

1.49611.49611.4961

1.49611.81101.8110

1.81101.81102.2047

2.2047

.012

.012

.012

.012

.012

.012

.012

.012

.012

.012

.012

.012

.012

.025

.025

.025

.025

.040

.040

.040

.040

.040

.040

.040

.040

.040

.040

.040

.040

.040

.060

.060

.060

.080

.080

.080

.080

.080

.080

.080

.080

.080

.080

.080

.100

.100

.10

.11

.12

.14

.22

.28

.32

.36

.40

.49

.54

.70

.771.051.15

1.241.321.90

1.982.062.14

2.292.953.19

4.134.465.49

5.717.067.34

8.819.179.87

13.414.517.8

22.022.924.6

25.535.336.7

38.139.551.7

53.7

410427468

505790980

1 0101 0701 110

1 3601 4001 870

1 9602 6302 720

2 8102 9204 380

4 3804 4704 560

4 6806 3206 540

8 4808 770

11 000

11 10013 90014 000

16 70017 10017 500

24 30025 00031 000

38 70038 70040 000

40 90054 40055 500

56 40057 30070 100

73 100

209234281

328504652

764854933

1 1501 2401 650

1 8002 4702 650

2 9003 0804 410

4 5904 7704 950

5 3106 8607 310

9 67010 50012 800

13 50016 50017 200

20 60021 40022 900

31 50033 70041 100

51 30053 10057 300

58 50082 10085 400

87 70091 000

119 000

126 0001) Fillet radius indicates maximum fillet radius on shaft or in housing which bearing corner will clear.2) Listed values are for pressed steel cage for 1800S through 1828S and 1834S and 1856S. All others for outer land guided machined bronze.

The values have been determined through historical application and practice. For a more complete explanation, see page 274.3) Rating for one million revolutions or 500 hours at 33| RPM.4) Typically non-stocked sizes, please check availability before designing into equipment.

1900-S Series Extremely Light Series

45

1900-S Series bearings are single-row radial conrad-type bearings that can accommodate light radialloads, two-directional thrust loads, or a combinationof both. They are designed for applications where a lack of space or limitations on weight require abearing with a thinner section than 100-KS Seriesbearings. Some sizes are available with shields orseals.

MRCBearingNumber

Bore

dmm in


Width

Bmm in


ZD2

mm in

DynamicC3)

N lbf


StaticC0

N lbf



GreaseRPM

1900S1901S1902S

1903S1904S1905S

1906S1907S1908S

1909S1910S1911S

1912S1913S1914S

1915S1916S1917S

1918S1919S1920S

1921S1922S1924S

1926S4)1928S4)1930S4)

1932S4)1934S4)1936S4)

1938S4)1940S4)1944S4)

1948S4)1952S4)1956S4)

1960S4)1964S4)1968S4)

1972S4)1976S4)1980S4)

1984S4)1988S4)1992S4)

101215

172025

303540

455055

606570

758085

9095

100

105110120

130140150

160170180

190200220

240260280

300320340

360380400

420440460

222428

303742

475562

687280

8590

100

105110120

125130140

145150165

180190210

220230250

260280300

320360380

420440460

480520540

560600620

667

799

91012

121213

131316

161618

181820

202022

242428

282833

333838

384646

565656

566565

657474

.30

.30

.30

.30

.30

.30

.30

.64

.64

.64

.641.0

1.01.01.0

1.01.01.0

1.01.01.0

1.01.01.0

1.51.52.0

2.02.02.0

2.02.02.0

2.02.02.0

3.03.03.0

3.04.04.0

4.04.04.0

84103142

155252271

317432637

683728864

864968

1 300

1 3701 4501 810

1 9202 0252 550

2 7702 7703 460

4 1004 3205 670

6 0006 3308 060

8 06010 20010 800

11 90016 40017 300

22 70024 00025 300

26 70032 40034 100

35 80043 10045 400

2 5102 9104 030

4 360 6 3706 630

7 2809 560

13 800

14 00014 60016 500

16 50017 40023 800

24 20025 10031 900

32 50033 80042 300

44 20043 60055 300

65 00066 30088 400

92 30093 600

119 000

117 000148 000151 000

159 000212 000216 000

270 000276 000281 000

291 000338 000345 000

351 000410 000423 000

1 1201 5002 040

2 3203 6504 150

5 0006 800

10 000

10 80011 80014 000

14 30016 00021 200

22 40024 00030 000

31 50033 50041 500

44 00044 00057 000

67 00071 00093 000

98 000104 000132 000

134 000166 000176 000

196 000270 000285 000

375 000390 000415 000

440 000530 000560 000

585 000710 000750 000

34 00030 00024 000

22 00018 00016 000

14 00011 00010 000

9 0008 5008 000

7 5006 7006 300

6 0005 6005 300

5 0004 8004 500

4 3004 0003 600

3 4003 2002 800

2 6002 4002 200

2 2002 0001 900

1 8001 6001 500

1 3001 2001 100

1 1001 000

950

900900850

40 00036 00030 000

28 00022 00019 000

17 00014 00013 000

11 00010 0009 500

9 0008 0007 500

7 000

Documents

MRC Bearing Engineering Handbook