MPDS 00-99-01 Rev_1 (2011)

MPDS 00-99-01 Equipment and Materials Source List

Malaysian Project Design Specification April 2011

Upstream MPDS 00-99-01 REV 1

Page 1 of 114

EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.

Equipment and Materials Source List Malaysian Project Design Specification

MPDS 00-99-01

1 1 Apr 2011 Update and Sections Additions RMS LBW LBW DCS

0 23 Nov 2010 Initial Publish RMS LBW LBW DCS

Rev. Issue Date Description Document Custodian

Endorser System

Administrator System Owner




Page 2 of 114


Scope

This Malaysian Project Design Specifications (MPDS) contains the names of acceptable product

manufacturers, which shall be used by Fabricators, Contractors and Equipment Packagers to

procure equipment/materials in the listed category for supply to EMEPMI. Notwithstanding the

above, purchase of products from these manufacturers is still subject to the products meeting the

required delivery date and complying with relevant EMEPMI specifications.

Purchase of equipment/materials from other manufacturers not specified herein is a deviation to

this Malaysian Project Design Specifications (MPDS) and shall require prior EMEPMI approval.

EMEPMI approval may be granted under any of the following conditions:

a) Product cannot be sourced from the listed manufacturers.

b) Deviation will result in a significant improvement to project schedule.

c) Deviation will result in a significant cost saving (vs. buying from listed manufacturers), whereby a portion of that cost shall be reimbursed to EMEPMI.

This data is supplied to aid the Fabricator, Contractor and Packagers in determining who the

Malaysian Agent is for each products manufacturer listed. It is the Fabricator's responsibility to

ensure that the manufacturers listed have local agents and are registered with PETRONAS.




Page 3 of 114


Table of Contents

1. Required References ............................................................................................ 5

1.1. Company Technical Sheet ........................................................................... 5

2. Definitions.............................................................................................................. 5

3. Corrosion Protection ............................................................................................ 5

4. Rotating Machinery............................................................................................... 7

5. Mechanical – Static ............................................................................................. 12

6. Pressure Vessels ................................................................................................ 15

7. Heat Exchangers ................................................................................................. 17

8. Mechanical Valves .............................................................................................. 19

9. Process Piping .................................................................................................... 22

10. Process Equipments........................................................................................... 24

11. Fire Protection..................................................................................................... 29

12. Life Safety ............................................................................................................ 30

13. Flare System........................................................................................................ 32

14. I&C........................................................................................................................ 32

15. Telecom................................................................................................................ 44

16. Electrical .............................................................................................................. 46

17. Structural & Architectural................................................................................... 52

18. Marine................................................................................................................... 53

19. Surf (Marine) ........................................................................................................ 55

20. Forging................................................................................................................. 57

21. Duplex Stainless Steel ........................................................................................ 62

22. Upstream Acceptable Manufacturers of Structural Plate, Shape and Tubular Products............................................................................................................. 111




Page 4 of 114


Record of Change ..................................................................................................... 112

Attachment: Purpose Codes Definitions................................................................ 113




Page 5 of 114


1. Required References

This Section lists Practices and Standards that are generically referenced and assumed to be a part of this

document. Unless otherwise specified herein, use the latest edition.

1.1. Company Technical Sheet

TS 29-01-09 Upstream Acceptable Manufacturers of Structural Plate, Shape and

Tubular Products.

2. Definitions

Yellow Highlighted Lines = Supplier has been put on the Watch List due to performance

issues or there is important information that needs to be considered before a decision is made to use them. Please review prior to placing an order.

Red Highlighted lines = Do not use. Supplier has performance issues

3. Corrosion Protection

Category Description Manufacturer Remarks

Cathodic Protection Systems

Engineering and Installation Cathelco Group Corrosion Service Corrpro Matcor Nakabotec

Pipelines, Facilities, and Structures

Coatings and Linings FBE Coating Applicator Bayou Pipe Coating / CCSI Bredero Shaw Commercial Resins Co. EUPEC PPSCH Socotherm

Pipelines, Flowlines, Induction Bends

FBE Field Joint Coating Applicator

Bredero Shaw Commercial Resins Co. EUPEC Pipeline Induction Heat Ltd. (PIH) Socotherm Socotherm Bayou Pipe Coating / CCSI

Pipelines and Flowlines




Page 6 of 114


FBE Powder Manufacturer 3M BASF Dupont Jotun

Multi layer Insulation Coatings Bredero Shaw PPSCH Pipelines and Risers Multi layer Insulation Coatings

Applicator Socotherm Pipelines and Risers

Multi-Layer Polyolefin Coating (3 Layer PE and PP) Applicator

Socotherm Pipelines and Risers

Multi-Layer Polyolefin Coatings Bredero Shaw EUPEC PPSCH

Pipelines and Risers


Carboline Hempel International Coatings Jotun Sherwin Williams PPG

Polychloroprene Applicator Socotherm Risers Polychloroprene Coating Baker Rubber

Bredero Shaw Mark Tool Company PPSCH Trellborg Viking

Risers

Polyethylene Jacketed Polyurethane Foam Insulation

Bredero Shaw Logstor A/S


Polyurethane Foam Infill Coating Applicator

Offshore Joint Services (OJS) Pipeline Induction Heat Ltd. (PIH) EUPEC

Pipelines

Subsea Insulation Bayou Flow Technologies Bredero Shaw Trelleborg Offshore

Weight Coating Bayou Pipe Coating Bredero Shaw EUPEC PPSCH


Weight Coating Applicator Socotherm Pipelines and Flowlines Corrosion Inhibitors Amtech Chemical Sdn

Bhd Maces Sdn Bhd Premier Enterprise Corporation (M) Sdn Bhd

Corrosion Monitoring Equipment


Caproco Cormon Corrocean Deepwater Corrosion Services Rohrback-Cosasco

Electrical Isolation Monolithic Isolation Joint ALFA Engineering Zunt

Fluoropolymer Bolt Coatings


Asemco Co. Custom Coating Applicators E/M Coating Services High Technology




Page 7 of 114


Coating Company International Polymer Lone Star Fasteners Praxair/Smaltirivia Seng Heng Engineering PTE Southwest Plating Southwest Impregion Fluid Sealing Products Allegheny Coating American International Industries Southern Bolts and Nuts Sdn Bhd Status Head Sdn Bhd

Sacrificial Anodes Pipelines, Facilities, and Structures

CP Tech Galvotec Impalloy Metec Samgong Skarpenord Wattyl Dimet MPE

4. Rotating Machinery

Category Description Manufacturer

Axial Compressors Demag Delaval Sulzer Centrifugal Compressors

API 617 Dresser-Rand Co Sulzer

Elliot-Ebara GE / Nuovo Pignone Ebara International / Elliot Turbomachinery Co Ltd Demag Delaval

GHH Borsig Mitsubishi Heavy Industries Rolls-Royce

High Speed / Low Flow Sundyne Corp Modular Construction Solar Turbines Inc Centrifugal Pumps ANSI Self Priming Gorman Rupp ANSI Solids Handling Gorman Rupp ANSI - Water Services Flowtronex PSI Inc. ANSI Ruhrpumpen Clyde Union (Weir Pump, Ltd.) Flowserve Corp

Pump Division ANSI Vertical David Brown Union Pumps API 610 BB1 Ebara Corp Flowserve / Worthington SPA

Flowserve Corp Pump Division Sulzer Pumps

Ruhrpumpen David Brown Union Pumps Nuovo Pignone Shin Nippon Machinery Co Ltd




Page 8 of 114


CPC Pumps International API 610 BB2 Ebara Corp Flowserve / Worthington SPA

Flowserve Corp Pump Division Sulzer Pumps Clyde Union (Weir Pump, Ltd.) Weir Gabbioneta Pumps

David Brown Union Pumps Nuovo Pignone Shin Nippon Machinery Co Ltd CPC Pumps International Ebara Corp Goulds Pumps Ruhrpumpen

API 610 BB3 Flowserve Corp Pump Division Sulzer Pumps Clyde Union (Weir Pump, Ltd.)

David Brown Union Pumps Nuovo Pignone Goulds Pumps

API 610 BB4 Flowserve Corp Pump Division

Nuovo Pignone Ebara Corp

API 610 BB5 Flowserve Corp Pump Division Clyde Union (Weir Pump, Ltd.)

Sulzer Pumps David Brown Union Pumps Nuovo Pignone Ebara Corp

API 610 OH1 Flowserve / Worthington SPA Flowserve Corp Pump Division

Goulds Pumps API 610 OH2 Flowserve Corp

Pump Division Flowserve / Worthington SPA Clyde Union (Weir Pump, Ltd.)

Sulzer Pumps David Brown Union Pumps Shin Nippon Machinery Co Ltd CPC Pumps International Ruhrpumpen

API 610 OH3 Flowserve Corp Pump Division

David Brown Union Pumps CPC Pumps International

API 610 OH4 Flowserve Corp Pump Division

Goulds Pumps David Brown Union Pumps Niigata Worthington Co Ltd CPC Pumps International

API 610 OH5 Flowserve Corp




Page 9 of 114


Pump Division Clyde Union (Weir Pump, Ltd.)

Sundyne Corp API 610 OH6 Nikkiso

Sundyne Corp API 610 VS1 Flowserve Corp

Pump Division Sulzer Pumps David Brown Union Pumps API 610 VS2 Flowserve Corp

Pump Division Sulzer Pumps David Brown Union Pumps

Ebara Corp API 610 VS3 Flowserve Corp

Pump Division Sulzer Pumps Clyde Union (Weir Pump, Ltd.) API 610 VS4 Ebara Corp Flowserve (AUSTRIA) Gmbh

Flowserve Corp Pump Division

API 610 VS5 Ebara Corp Flowserve (AUSTRIA) Gmbh

Flowserve Corp Pump Division

API 610 VS6 - Cryogenic Ruhrpumpen API 610 VS6 - General Service Sulzer Pumps API 610 VS6 Clyde Union (Weir Pump, Ltd.) David Brown Union Pumps

API 610 VS7 Sulzer Pumps API 610 Water Services Sulzer / Johnston Pump API 674 Reciprocating David Brown Union Pumps API 685 Sealless Sulzer Pumps Sundyne Corp./Kontro Firewater Service

Flowserve Pte Ltd Flowserve Corp Pump Division Clyde Union (Weir Pump, Ltd.)

Sulzer / Johnston Pump Sulzer Pumps

Firewater Service - Engine Driven Main Firewater Pump

Goulds Pumps

Main Oil Line

Blakers Pump Engineers TKL (S/P) United Pumps

Sealless Hermitic Pumps Inc

Seawater Lift Pumps - Firewater Pumps

Frank Mohn Flatoy AS (Framo)

Slurry GIW (Georgia Iron Works) Weir Minerials North America

Submersible HP Reda (Pumps & S/P) Submersible LP Grunfos Compressor Components

Bearing / Bushings - Swivel Bearings

Avon Technical Products Rotek

Bearing / Bushings - Turntable Bearing

Rotek Rothe - Erde Avon Technical Products




Page 10 of 114


SKF

Compressor Seals - Dry Gas Flowserve Corp Pump Division John Crane Company LLC

Compressors Instrument Air Atlas Copco Process Air and Gas Toromont Process Systems Inc Utility and Instrument Air Tide Air Inc Couplings API 671 Lucas Aerospace Metastream General Service Metastream

Thomas Fans Buffalo Forge Fan Company

Howden Buffalo Gas Turbines Aeroderivitive - LM 2500 GE / Nuovo Pignone Gas Turbine Air Inlet Filters

AAF Altair Donaldson

Gas Turbine Fire Suppression - Water Mist System

Eusebi

Generator Driver Rolls-Royce Solar Turbines Inc

Mechanical Driver - Power Turbines Dresser-Rand Co Mechanical Driver Rolls-Royce

Siemens Industrial Turbomachinery Solar Turbines Inc

Gears API 613 Flender Renk Lufkin Industries Inc. MAAG

Package Lube Oil Systems

Gerhardts TF Hudgins

Pumping Systems

DXP Sepco Ind AGI Industries Capital Process Equipment

Standby / Emergency / Essential Generator

Tractors Malaysia

Turbine Wash Water System Bob J Johnson & Associates Inc Positive Displacement Pumps

API 674 Reciprocating Cat Pumps

Peroni Pompe SpA API 675 Controlled Volume American Lewa

Bran+Luebbe Inc Milton Roy Pulsafeeder Lewa

API 676 Rotary Axflow S.A.S IMO Pump Roper Warran Pump

API 676 Rotary - Multiphase Bornemann API 676 Rotary - MPP Leistritz Corporation Chemical injection Texsteam Diaphragm Goulds Pumps

Texas Process Equipment Diaphragm - Air Operated Haskel Australasia P/L

Warren-Rupp/Sandpiper Wilden




Page 11 of 114


Diaphragm - Air Operated Transmark FCX Pty Ltd Diaphragm - Double Diaphragm

Pumps Winston Engineering Corp. SDN BHD

Gear Pump Northern Piston Duraqual

Milton Roy Morgan National Wheatley/Mono

Progressive Cavity

Allweiler Pump Mono Flow Moyno Inc Netzch Roper

Rotary Non API Viking Pump Pump Components Replicated Pump Parts Refine Engineering Seals Mechanical Flowserve Corp

Pump Division ProEight Offshore Engineering Sdn Bhd Seals Packing EGC

Utex Seals John Crane Company LLC Pumps ANSI Gasco Wheatley

Kinecor Inc Booster TKL (S/P)

United Pumps Booster Weir Engineering Diesel Circulating

Viking Pump Worthington

Utility - Potable Water / Hot Water Circ

Ajax Davey Onga Regent

Reciprocating Compressors

API 618 Neuman-Esser USA Inc Dresser-Rand Co Cooper Compression

GE / Nuovo Pignone Danmar Industries Inc

Reciprocating Engines

Diesel Pon Power Papendrecht Caterpillar

Reciprocating Compressors

Diaphragm Type

Burton Corblin

Medium Speed Ariel Corporation Rotary Compressors

API 618 Helical - Air Only

Atlas Copco

Ingersoll Rand Company (Ingrand ACG.) API 618 Helical A-C Compressor

GE Power Systems Airdyne Danmar Industries Inc

GHH Borsig Howden Process Compressor

Process Air and Gas - Helical Kobe Steel Ltd Process Air and Gas - Wet Screw Ingersol-Jati Malaysia

Kobe Steel Ltd Steam Turbines API 611 Dresser-Rand Co

Ebara International / Elliot Turbomachinery Co Ltd API 612 Dresser-Rand Co

Mitsubishi Heavy Industries




Page 12 of 114


Ebara International / Elliot Turbomachinery Co Ltd Instrument Air Gardner Denver

5. Mechanical – Static


Air Conditioning / HVAC York Alam Dingin Air Conditioning Engineering Sdn Bhd Dynac Sdn Bhd

Hull Only Carrier Marine & Offshore Alscott Air Systems Ltd

ABB Process Industries Direct Engineering Services DWD International LLC Hi Press Trane Tyco Australia Pty Ltd Direct Engineering Services (DES) Borg Warner

Cartridge Filter Package Peco Cranes Bridge and Jib Gaffey Cranes/ Parts and Repairs Kenz Cranes BV Hoist - Monorail Ingersoll-Rand

Beebe C-M

Pedestal Applied Hydraulics Favelle Favco Hochang Machinery Kenz Cranes BV Hydralift Hydralift / Molde Crane AS Hydralift ASA - National Oilwell Norway AS Liebherr Oil States Industries Stalprodukter Nautilus Unit Mariner Skagit Baker Marine SeaKing Weatherford Handal Offshore Services Sdn Bhd MS Herkules Sdn Bhd

Demethanizer Bottoms Flowserve Corp Pump Division

Diesel oil purifier Alfa Laval Elevators Champion Elevators Inc Filters Cartridge Filter Package Cuno Filters

Gameco Pall Australia Peco Plenty Filtration UK Process Materials P/L Southwest Filter Co Winston Manufacturing




Page 13 of 114


Hatfield AMF Reda Dollinger Daeham Kingtool Kvaerner Process Systema Baker Hughes Filtan Peerless Anderson

Cartridge Filter Package - Sulfate Removal

Natco Process

Process Filters / Elements Camfil Pty Ltd Cuno Filters Gameco Pall Australia Process Materials P/L USF Filtration Ltd Veolia Water Systems Vilair-AAF Velcon Peco

Quarters - Air Conditioning Haden Engineering Pty Ltd Fuji Filter Mfg Co Ltd

Foam Skid Chemetron Chubb/National Foam Dooley Tackaberry

Fuel Packages Diesel Centrifuge Fuel Package Alfa Laval Flowtronex PSI Inc. Westfalia Separator

Helifuel Package Flowtronex PSI Inc. HVAC Systems Custom Air Products & Services Inc Hydrocyclones Apex Process Systems

Krebs Engineering P/L Baker Process a Divn of Baker Hughes Aust Natco Process

Lube Oil Supply Package Flowtronex PSI Inc. Material Handling Equipment

Certex

Mixers Mechanical Driven Plenty Mixers (Lightnin) Nitrogen Gas Generator Air Products A/S Offspec Oil Heater Sung Jin Geotec Co. Ltd Oil Spill Clean Up Equipment

Crucial Inc

Pig Launcher / Receiver ClampOn AS Taylor Forge TD Williamson Inc Pipeline Equipment Co Sagebrush Pipeline Equipment Shaw Group SWECO Fab Inc

Pig Receiver Pipeline Onshore Fai Officine Di Carvico Potable Water Pressurizing Package

Bob J Johnson & Associates Inc

Pressure Water Sets Fisher Industries Production Manifold Dresser

FMC Seal Gas Cooler Sung Jin Geotec Co. Ltd




Page 14 of 114


Slug Catchers Finger Type - 5000 bbl, nominal 4.0 Gscfd wet gas (2&3 phase) up to 99# ASNI

Taylor Forge CMP Dunkerque

Tanks Atmospheric Tanks CB&I Constructors Pty Ltd CB&I Eastern Anstalt

LNG Storage I.H.I. Non Hazardous Open Drain

Separator Tank Natco Process Hitachii Zosen Mechanical Corp

Floating Roof HMT Inc TEG Regen Package Prosernat Utility Vessel Package Heat Exchangers International

Kvaerner Process Systems US Inc. Prosernat En-Fab Inc Natco Process Sung Jin Geotec Co. Ltd

UV Sterilizer Package Bob J Johnson & Associates Inc Washdown Package HP Hot Water Wash Down Package John Zink Company, LLC Washdown Package AGI Industries

Petrex Flowtronex PSI Inc. Hydromeca

Waste Heat Recovery Tulsa Heaters Inc GE / Nuovo Pignone Deltak LLC

Waste Incinerators Natco Process Zeeco

Waste Removal Trash Compactor Enviro-Pak Compactors Waste Treatment Sewage Treatment Package Electrocatalytic Ltd

Red Fox Environmental Services Inc Fast / Smith and Loveless Inc Marine Equipment DIvision

Waste Treatment CETCO Environmental Offshore Service Christ Kennicott Water Technology Ltd

Waste Treatment Equipment

Anderson Water Systems Aquatech Ecodyne

Water Purifiers Alfa Laval Watermakers Distillation Alfa Laval

Beaird Industries High Purity Wash Water Skid C'treat Offshore Inc Potable Watermaker Skid 1 & 2 C'treat Offshore Inc Reverse Osmosis C'treat Offshore Inc

Aquachem Permutit Village Marine Bob J Johnson & Associates Inc

Wet Air Receiver Sung Jin Geotec Co. Ltd Absorber Hitachii Zosen Mechanical Corp Chemical Injection Package

Lewa Milton Roy McFarland Pulsafeeder Texsteam William FMC Bran Leubbe Wilden Haskel




Page 15 of 114


Checkpoint Methanol / Hypochlorite Flowtronex PSI Inc.

Bran+Luebbe, Inc Flowtronex PSI Inc. Milton Roy & Blakers Pump Engineers

Cooling Medium Emergency Air Cooler

GEA Rainey Corp

Fuel Oil Filtration Package FiltraTech Gas Dehydration and Gylcol Regeneration Packages

Prosernat Natco Process

Heaters Fired <100MBTU Foster Wheeler USA Fired Heater Div Tulsa Heaters Inc

Fired Optimized Process Furnaces

Industrial Steam Boiler up 1500 psig, up to 240 tonnes/hr modular/up to 315 tonnes/hr field erected

Macchi Steam & Power Generation

Liquid Incinerator John Zink Company, LLC Zeeco

Multimedia Filter Package Natco Process Tower Internals High Capacity Mesh and Vanes Koch-Otto York Trays and Packing

- Mercury Bed Calgon Carbon Co. UOP

Trays and Packing KochGlitsch Sulzer Chemtech AG Sulzer Chemtech PTE Ltd Sulzer Chemtech USA Inc Raschig GMBH UOP

Cyclones Burgess Manning High Capacity Mesh Amistco

Burgess Manning CDS KnitMesh

Vanes Amistco Burgess Manning CDS KnitMesh Peerless

Y Strainers Texas Steam Equipment Aitken Inc Barton Firtop Fuji Filter Mfg Co Ltd Eurofiltec Delmar Hayward Harfield Leslie Nicholson Zurn

6. Pressure Vessels


Large Diameter / Heavy Wall Pressure Vessel

Carbon Steel Vessel/Column (Up to 35mm Thickness) - Over 60mm or Over 100ton

Doosan Mecatec




Page 16 of 114


CS up to 150mm thk Sewon Collentech - S Korea

CS/W SS Clad up to 150mm thk Sewon Collentech - S Korea

Cyrogenic Deethanizer Tower ATB Acciaieria e Tubificio di Brescia S.P.A. Beaird Industries Belleli Energy c/o The Hanover Co Felguera Caldereria Pesada S.A. Larsen and Tourbro Ltd

Large Diameter / Heavy Wall Pressure Vessel

Desalter Natco Process

SS up to 150mm thk Sewon Collentech - S Korea

ADI (Australian Defence Industries) ASC Engineering P/L Fusion Weld (address on Project basis) Fitzroy Engineering (NZ) L & A Pressure Welding ATB Caldereria Beaird Industries Belleli Bosco Duro Felguera General Welding Hitachii Zosen Mechanical Corp I.H.I. Japan Steel Mitsubishi Heavy Industries Hyundai

Natco Process Pressure Vessels <2" Sung Jin Geotec Co. Ltd Natco Process API 650 Tanks Saunders International P/L ASME Kvaerner Process Systems US Inc.

Prosernat ASME - Div 1 and AS1210

Supplement 2 ASC Engineering P/L Fitzroy Engineering (NZ) L & A Pressure Welding

C.M. Expansion Tank Sung Jin Geotec Co. Ltd Carbon Steel <600 psi KNM Process Systems Sdn Bhd Carbon Steel >600 psi KNM Process Systems Sdn Bhd Carbon Steel Vessel / Column Sewon E & T Corp Carbon Steel Vessel / Column Up

to 50mm Thickness PT Daekyung Indah Heavy Industry

Closed Drain Flash Drum Sung Jin Geotec Co. Ltd CS - Up to 100mm thickness Ningbo Tianyi CS - Up to 100mm thickness,

limited to 1200mm in diameter Nanjing Chemical Machinery Works

CS - Up to 50mm thickness Furui De-Ethanizer Tower Sewon E & T Corp Flare Knockout Drum – HP Sung Jin Geotec Co. Ltd Flare Knockout Drum- LP Sung Jin Geotec Co. Ltd Fuel Gas scrubber Sung Jin Geotec Co. Ltd Fuel Gas Scrubber – LP Sung Jin Geotec Co. Ltd General Baipini Engineering Pty Ltd (Sydney)

Fusion Weld Hudson-HEI (Perth) L & A Pressure Welding Stelform




Page 17 of 114


Heating Medium Expansion Drum Sung Jin Geotec Co. Ltd HPC Dis. Scrubber Sung Jin Geotec Co. Ltd HPC Suction Scrubber Sung Jin Geotec Co. Ltd Instrument Air Receiver Sung Jin Geotec Co. Ltd IP Comp Suct Scrubber Sung Jin Geotec Co. Ltd IP Discharge Scrubber Sung Jin Geotec Co. Ltd IP Separator Sung Jin Geotec Co. Ltd Large Diameter / Heavy Wall

Pressure Vessel Sung Jin Geotec Co. Ltd

Medium Wall Vessels Petrozavodskmash Corp Medium/Heavy Vessels Larsen and Tourbro Ltd Methanol Storage Tank Sung Jin Geotec Co. Ltd NFPA 22 Firewater Tanks Bachmans

Saunders International P/L Nitrogen Receiver Sung Jin Geotec Co. Ltd SS - Up to 50mm thickness Furui SS - Up to 50mm thickness, limited

to 1200mm in diameter Nanjing Chemical Machinery Works

SS & Special Alloy Shanghai Morimatsu Stainless Steel Vessel / Column -

Over 50 ton Doosan Mecatec Hudson Industries Daekyung Machine and Engineering Company Ltd En-Fab Inc Doosan Mecatec

Unfired (Class II and Class III) Amalgamated Metal Builders (M) Sdn Bhd Unfired MSET Engineering Corporation Sdn Bhd

Petra Fabricators Jutasama AMC

Utility Vessel Packages Biapini Engineering Pty Ltd Separators Cyrogenic Deethanizer Tower IL Sung Engineering & Construction Co Ltd Filter - Small Diameter Burgess Manning

Kobe Steel Ltd KNM Process Systems Sdn Bhd Pall Filters Peerless Peco

Natco Process Hazardous Open Drain Separator

Tank Natco Process

HP Sung Jin Geotec Co. Ltd LP Sung Jin Geotec Co. Ltd Oily Water Burgess Manning Small Diameter AWC Inc Test Separator Sung Jin Geotec Co. Ltd Hudson Industries

Natco Canada Ltd Volgogradneftemash

7. Heat Exchangers


Chart Heat Exchangers c/o SME Aerial Cooler Vibo Valencia Air Cooled Hudson-HEI (Perth)

Jord Engineers




Page 18 of 114


Pleny Uniquip GEA-BTT Dynac Sdn Bhd

3XX SS GEA-BTT CS/LTCS GEA-BTT Air Cooler A.P.V. Spiro Gills

FBM-Hudson Italiana Spa GEA Air Exchangers, Ltd. Heat Exchangers International Hudson Products Korea Heat Exchanger Mitsui Shipbuilding & Engineering Nuovo Pignone, S.P.A. Olmi, S.P.A. Hamon D'Hondt SA Bronswerk Foster Wheeler Ltd Hammco Heat Exchanger of Australia Hudson-HEI

Brazed Aluminum (Cold Boxes)

Chart Industries Linde AG Kobe Steel Ltd Sumitomo Precision Products Chart Industries

Hairpin and Double Pipe Brown Fintube France Alco Products

Hudson-HEI RW Holland Inc

Plate & Frame Hisaka Works Ltd Alfa Laval Swep Tranter Tranter

Printed Circuit (PCHE) Heatric Shell and Tube Amalgamated Metal Builders (M) Sdn Bhd 3.5% Ni Hantech Ltd Carbon Steel

Baipini Engineering Pty Ltd (Sydney) Hudson-HEI Daekyung Machine and Engineering Company Ltd

Carbon Steel >600 psi Energy Exchanger Company Graham Manufacturing Ltd Heat Exchangers International Hitachii Zosen Mechanical Corp Japan Steel Kobe Steel Ltd Bagnolo

Carbon Steel <600 psi Energy Exchanger Company Fabsco FBM-Hudson Italiana Spa Fusion Weld Graham Manufacturing Ltd H Leffer Hitachii Zosen Mechanical Corp Japan Steel Leffer Ohmstede (Exell, Inc.) Olmi, S.P.A. Bosco Bagnolo




Page 19 of 114


Metropolitan Engineering & Fabrication Proser Plenty Uniquip Belleli Bronswerk Constructions Metalliques Leffer Heat Exchanger of Australia

Carbon Steel / Alloy >600 psi Leffer Mitsui Shipbuilding & Engineering Nuovo Pignone, S.P.A.

Carbon Steel Vessel / Column SS Sewon E & T Corp SS Shanghai Morimatsu Stainless Steel

Daekyung Machine and Engineering Company Ltd I.H.I. Jord Engineers L&A Pressure Welding Stelform

8. Mechanical Valves


Acceptable Manufacturing

Facility (City/Country)

Ball 1/4" to 2" 1000psi to 15000psi

Ferritic Alloys and SS

Oliver Valves Ltd UK

1/4" to 1-1/2" 1000psi to 6000psi

DSS and SS Tyco Richards Alfa Valvole

Australia Italy

Actuated Crane Canada Inc Canada Floating Ball < 6" Cooper Cameron

Neles-Jamesbury PBV Valvitalia Velan Inc ABV Srl (Italy) KVC UK KITZ TYCO RICHARDS OMB GROVE ITALIA RBR VALVOLE ALFA VALVOLE

USA, Finland Stafford TX, USA Italy Global Italy JAPAN AUSTRALIA ITALY ITALY ITALY ITALY

Cryogenic OMB Kitz (Japan) Pibiviesse Pibiviesse SPA.

Italy Japan Italy Italy

Floating Ball <2" Grove - Italia SRL Italy Metal Seat Fire Safe Carbon / Low

Chrome / SS Neles-Jamesbury Orbit GROVE ITALIA RBR VALVOLE MIR VALVES ORSENIGO (FLUITEK)

USA, Finland USA

Resilient Seated Fire Safe Carbon / Low Chrome / SS

Cooper Cameron Neles-Jamesbury

Global USA, Finland




Page 20 of 114


Orbit WKM

USA USA

Subsea Ball Valves Cooper Cameron PetrolValves

Global Italy

Trunnioin Mounted

>2"

Cryogenic Pibiviesse Kitz (Japan) Perar Poyam Valves

Italy Japan Italy Spain

Trunnion Mounted >2"

ABV Srl (Italy) Cooper Cameron Grove - Italia SRL Pibiviesse Valvitalia Velan

Italy Global Italy Italy Italy Global

Trunnion Mounted >2" Argus Borsig CORT Hindle Cockburns M&D TK KVC (UK) Crane Australia Tyco Richards PCC KTM RBR VALVOLE ORSENIGO (FLUITEK) BREDA ENERGIA RING-O VALVE DELLA FOGLIA MIR VALVES

Germany Germany UK Australia Australia Italy Japan ITALY ITALY ITALY ITALY ITALY MALAYSIA

Bronze, Nickel Aluminum Bronze

Seawater Service

CRANE SHIPHAM

UK UK

Butterfly Xomox Corp. Adams Armaturen Houston TX USA,

Germany API 609 >2" Cooper Cameron

Neles-Jamesbury Demco

Global USA & Finland Global

API 612 >2" Flowseal Germany Metal Seat Fire Safe High

Performance, API 609 – Category B, Carbon, Alloy, SS

Posi-Seal (Fisher-Emerson) Vanessa

Italy

On-Off Metso Field Systems OY Tyco Valves & Control Distribution

Resilient Seated Fire Safe High Performance, API 609 – Category B, Carbon, Alloy, SS

Flowseal Keystone International Neles-Jamesbury McCanna Posi-Seal Winn

Germany Italy USA & Finland

Rubber Liner and / or Seat

Air and water

Class 150 & Lower, Water

Keystone International Flowseal

USA




Page 21 of 114


service & water Lug Types, API 609 – Category A, Iron & Carbon Steel

Triple Eccentric

Cryogenic Orton Vanessa Adams-Armaturen

Italy Italy Houston TX USA, Germany

Bronze, Nickel Aluminum Bronze

Seawater Service

CRANE SHIPHAM

UK UK

Check 1/4" to 1" 1000psi to

6000 psi SS


Cast CS & Cast L.T.C.S.

150# & 300# Goodwin International Ltd UK

Cast SS Cryogenic Goodwin International Ltd UK Large bore, swing

check Kitz Japan

Pacific Powell Walworth Wheatley Grinnell Entech Velan Malbranque

Non Slam Goodwin International Ltd Crane Canada Inc Mokveld Valves Bv. Daniel Stockham

UK Canada Netherlands USA Australia

Special Check Valves

Goodwin International Ltd UK

Wafer >2" Crane Canada Inc Duo-Check Crane

Canada Conroe TX, USA

Wafer & Wafer Lug Goodwin International Ltd Crane Australia

UK Australia

Water Service IBBM, All Iron, Bronze

Proquip Dual Plate

Velan Kitz Tom Wheatley

Global Japan USA

Gate 1/2" to 1" 1000 psi to 15000 psi



Gate >2" Jenkins

Gate / Globe / Check

Poyam Valves Cooper Cameron Valves Raimondi

Spain Global USA, Canada

>2" Bel Valves OMB Crane Pacific Powell Walworth Velan Malbranque Grinnell WKM

UK Italy




Page 22 of 114


API 600 Carbon Steel - Flanged & Butt welded

Tong Yung (TY) Korea

API 602 All materials

Bonney Forge DSI SWI Valve Vogt Pacific Smith Valves Stockham Crane

USA, Italy Italy S Korea USA

OMB API 603 & ASME

B18.34 SS & Alloy – incl. Low Chrome

Pacific Tong Yung (TY) Velan Inc

Long Beach, USA Korea Global

Bronze Valves Kitz USA Cast Carbon Steel Class 600

and above Pacific Long Beach, USA

Cast CS & Cast L.T.C.S.

Class 150# and 300#

PK Valves Korea

Class 600# and Above

Velan Inc Global

Forged < 2" Tong Yung (TY)

<1.5" Saccap Service Smith Valves

France Houston TX USA

Water Service IBBM, All Iron, Bronze

Kitz Milwaukee

USA

Air & Water Service Brass & Bronze

Kennedy Milwaukee Valve Stockham

Elmera, NY USA Milwaukee, WI USA Cullman USA

< 2" Cryogenic OMB > 2" Cryogenic Tong Yung (TY) Korea Manifold ACECO

FMC Texsteam

USA USA

Needle 1/4" to 1" 1000psi to 15000 psi


Oliver Valves Ltd Anderson Greenwood Astava Kenmac Marsh Precision General Whitey

UK

Special Axial Flow Check Valves

Mokveld Valves Bv.

9. Process Piping

Category Manufacturer Acceptable Manufacturing Facility

(City/Country)

Alloy 20 and other Nickels Mitsubishi Materials Japan

LOW CHROME UP TO 13% Kawasaki Koppel Steel

Japan Usa




Page 23 of 114


Mannesmann Sumitomo Tubacex Vallourec

Germany Japan Spain France

Bends for SCR & Flowlines Dalmine Italy Carbon Steel Dalmine Italy Carbon Steel Seamless - Impact Tested

Dalmine S.P.A. Italy

Carbon Steel Seamless - Impact Tested -- EFW

D'Amore & Lundardi S.P.A.

Carbon Steel - Seamless

Koppel Steel North Star Sharon Tube Tubacex U.S. Steel Vallourec Nippon Steel Corp. V & M Do Brasil Sa

Usa Usa Usa Spain Usa France Japan Brasil

Carbon Steel – Seamless and Welded

Sumitomo Metal Industries, Ltd. Japan, Europe

Carbon Steel Welded - ERW

Newport Steel Usa

Carbon Steel

Benteler Berg Steel Pipe Corp. Confab CSI Tubular Products EEW Hyundai Ilva S.P.A. JFE Kawasaki Mannesmann Maverick NKK Siderca Sumikin Bussan Corp Tex-Tube Company Thyssenkrupp Mannex Gmbh Sif Group Bv Kurvers Inc

Germany USA USA USA Germany, Korea Korea Japan Japan Germany USA Japan Argentina Japan Houston TX, USA Germany USA

Carbon Steel, SS, Alloys Seamless

V & M Tubes Europe, Usa

Coating Europipe Gmbh Germany Coating External - Weight

Compression Coat Inc. Usa

Copper Nichel Vdm Austrailia Copper Nichel Norman W Hutchison Fittings Seamless, Welded

Sk Bend Korea

Flexible Pipe Technip - Coflexip France Flexible Pipe Wellstream UK

FRP Piping Components Ameron Pte Ltd FIBERBOND

USA, MALAYSIA

HDPE Pipe, Fittings, Flanges Great Western Supply Co

Induction Bends

Fabricom Bassi Luigi Bendtec Dai Ichi High Frequency Co. Ltd.

Belgium Italy USA Japan




Page 24 of 114


Germany USA

Mannesmann Pacific Pipe Company Simas Shaw Sunland

Insulation - Line Blankets Bd Profiles Ltd Pipe Fabrication - Pipe A672 / API

Eew Germany, Korea

Pipe Spool Fab and Induction Bends

Sung Il Co., Ltd. (Sim) Korea

Stainless Steel Kobe Steel Ltd Nippon Steel Corp. Kurvers Inc

Japan Japan Usa

ALLOY, SS, MONEL AND ETC.

Al Tech Avesta Curtis Wright Haynes Inco Alloy Kawasaki Mannesmann Sandvik Schoeller Bleckman Sumitomo Swepco Tad Usa Trent Tube Tubacex

Usa Usa Usa Usa Usa Japan Germany Usa/Sweden/Canada Austria Japan Usa Usa Usa Spain

Stainless Steel & Incoloy 825 Officine Orsi Spa Prochem Pipeline Products Onesteel Piping Systems

Italy Austrailia Austrailia

10. Process Equipments

Category Description Manufacturer Acceptable Manufacturing


Bolts Bolts for SPO Flange 100%

Compact Flange Canada

High Tensile Bolts Hobson Engineering Australia Southern Bolts & Nuts Sdn Bhd

J. Blackwood & Son Lone Star

Australia Houston, TX USA

Hight Tensile Studbolts & Nuts

Lamons Gasket & Bolt Company TX, USA

Studded Bolts & Nuts Hwashin Bolt Korea Barrel Closures Bandlock 2 Coated Bolts & Nuts

American International Industries

Closures

Gd Closures Grayloc Lts Inc Re-Flange

USA USA UK

Dampers Wahlco Metroflex, Inc USA Expansion Joints Metal Unaflex USA

Metallic

Bachmann Industries Badger Expansion Joint Systems Flexonics, Inc.

USA USA USA USA




Page 25 of 114


Hy-Span Microflex Inc

USA USA

Non Metallic

Proco Products Bachmann Industries Expansion Joint Systems Garlock General Rubber Goodall Rubber Wahlco Metroflex, Inc Jord Pathway Bellows

USA USA USA USA USA Canada USA Australia

Fittings

Nippon Steel Corp. Sam Yang Metal Prochem Pipeline Products Onesteel Piping Systems

Japan Korea Australia Australia

Barred Tees Kurvers France Sarl Bassi Luigi Moffat 2000 Ltd

France Italy UK

Branch Outlet Fittings (O'lets)

Anvil / Canvil Fuji High Pressure Iml Mega Penn Machine Tk Corporation Westbrook Wfi International Bkl Bonney Forge

USA, Canada Japan Italy Italy USA Korea Houston, TX USA Houston, TX USA UK Italy, USA

Branch Outlet Fittings (O'lets)-CS only

Phoenix Forgings USA

Buttweld End Fittings

Genoyer Group Inc Tk Corporation Integris Metals Bonney Forge Fuji High Pressure Taylor Forge Technoforge, S.P.A. Ladish Mill Iron Works

USA Korea Canada Italy, USA Japan USA Italy USA USA

Buttweld End Fittings

Benkan Custom Alloy Dynamic Products Flo-Bends Inc Interfit Mannesmann Ram Forge & Steel Sumitomo Metal Industries, Ltd. TK Corporation Tube Turns WFI International Integris Metals Penn Machine BKL

Japan USA Houston, TX USA USA France Germany USA Japan Korea USA Houston, TX USA Canada USA UK

Shaw Alloy Piping Products

Buttweld End Fittings-Carbon Steel

App Erne Tubeline Wilhelm Gelbach Coveco

USA AUSTRIA USA GERMANY VENEZUELA




Page 26 of 114


Hackney (Ells Dated 4/91 Or Later) USA Tube Forging Of America (Logo: Tfa) USA

Vallourec/Interfit (Elbows And Reducers Only)

FRANCE

Chero Piping Canadoil Forge Ltd Anggerik Laksana Sdn Bhd (Elbows up to 24” , Reducers up to 36”, Tees and Caps)

Buttweld End Fittings-Low Chrome (up to 13% Chrome)

App Erne Petrol Raccord Wihelm Gelbach Coveco

USA AUSTRIA ITALY GERMANY VENEZUELA

Wilhelm Schulz (Ell Dated 6/92 Or Later)

GERMANY

Canadoil Forge Ltd

Buttweld End Fittings-Alloy

App Erne J&J (Reducers Only) Petrol Raccord

USA AUSTRIA USA ITALY

Wilhelm Schulz (Ell Dated 6/92 Or Later)

GERMANY

Buttweld End Fittings-Stainless Steel

App Erne Flowline Petrol Raccord Coveco

USA AUSTRIA USA ITALY VENEZUELA

Wilhelm Schulz (Ells Dated 6/92) GERMANY

Supaflo Sse Sterling Tubes Galperti Canadoil Forge Ltd Anggerik Laksana Sdn Bhd (Elbows up to 24” , Reducers up to 36”, Tees and Caps)

Copper Nickel Vdm Norman W Hutchison

Australia

Forged Steel Fittings

Alloy Stainless Products Ladish Mega Anvil / Canvil Bonney Forge Camco (Capitol Mfg) Delcorte Fuji High Pressure Iml Taylor Forge Technoforge, S.P.A. Tube Turns Westbrook

USA USA Italy USA, Canada Italy, USA USA France Japan Italy USA Italy USA Houston, TX USA

Forged Steel Fittings-ANSI B16.11

Standard Fittings (Cs Only) Vogt

USA USA

Forged Steel Unions Wfi International Houston, TX USA Incolog 825 Officine Orsi Spa Italy




Page 27 of 114


Pipe Nipples-Straight - All Materials

Beck Gallagher Grinnel (Except Galvanized) J.B. Smith Missouri Pipe Fittings (Mpf) Merit Brass

USA USA USA USA USA USA

Swage Nipples - All Materials

J.B. Smith W.C. Norris

USA USA

Low Temp. Pipe Fittings (A333)

Techtubi Ibf Galperti

Flange Isolation/ Insulating Kits

Pikotek USA/Canada

Flanges Compact Flanges Lts Inc Vector International

USA Norway

Duplex Integris Metals Canada Flange Isolation Kits

Pipeline Seal & Insulator Houston TX, USA

Flanges

Boltex Buffalo Flange Flo-Bends Inc Forgerossi Kofco Ladish Melesi Metalfar National Flange Piping Products Shimoda Iron Works Sumitomo Metal Industries, Ltd. Tube Turns WFI International

Houston TX, USA USA Italy S. Korea USA Italy Italy Houston TX, USA Houston TX, USA Japan Japan USA Houston, TX USA

CS

Burton Delingpole Coffer Conforja Daniel Forjas De Santa Clara (Logo: Puma) Hackney Kerkau

UK USA BRAZIL USA VENEZUELA USA USA

Hanger Galperti Houston, TX USA, Italy

Low Temperature Machinefabriek-Heerbaart Bv Albert Grefenberg Gmbh + Ko Kg

Orifice Flange Euromisure Srl Italy Protector Hydratight Italy

Stainless Steel And Other Alloys

Bebitz Flowline Gerlin/Tube-Line Stainless Ideal Maas Texas Metals Western Forge

GERMANY USA USA USA USA USA TEXAS

SS, CS and Other Alloys Wildhelm Geldbach Ulma/Enara

GERMANY SPAIN

Stainless Steel Integris Metals Canada Flanges & Connectors

Welding Units UK

Flanges & Fittings Carbon & SS Van Leeuwen Pipe And Tube Europe Kurvers Rolled Alloys International Ltd

Netherlands France, Houston TX USA UK




Page 28 of 114


Techdrill UK

Gaskets

Tekno Logam Sdn Bhd Alfa-Meli Precision Industries Sdn Bhd Novus Sealing (M) Sdn Bhd

For Heat Exchangers Garlock Sealing Technologies Specialised Gaskets Pty. Ltd. (Flexitalic Licensee)

Australia

Ring Joint

Flexitallic Klinger Kukil Inntot Samsung Industry

UK S Korea S Korea

Spiral Wound Flexible Graphite filled

Econosto Singapore Pte Ltd Flexitallic Furon/Garlock Hofland Deltaflex Lamons Gasket & Bolt Company Klinger Kukil Inntot Metaflex Samsung Industry Cartec Sealing Tech

UK S. Korea UK S. Korea S. Korea

Hose and Hose Fittings

Grayco Washdown Assys Tyco Flexible Piping Systems

Australia Australia

Hub Clamp Connectors

Galperti Grayloc

Houston, TX USA, Italy

Induction Bends High Frequency Bending Sung Il Co., Ltd. (Sim) S Korea

Isolation/ Insulating Joints

Oil States Industries, Inc. Tube Turns Zunt Italiana S.R.L

USA USA Italy

Lifting Equipment & Rope

A Noble & Son Australia

Miscellaneous HDPE Liner Gse Lining Technology Gmbh Germany Swivel Components Marberry Machine Non Metallic, Fiberglass

Pipe / fittings Ameron

O-Ring International Seal Co. Parker Hannifier (Australia) Pty Ltd

Austrialia USA

Pipe Couplings Dresser Flow Control Stafford TX, USA

Pipe Hangers & Supports

Constant Spring Cams, variable Spring Cams, Clamps, Shoes & Guides

Aaa Technology Binder Group Pty Ltd Rilco Manufacturing Inc

Pipe Supports Pipe Hangers and Clamps Onesteel Piping Systems J. Blackwood & Son

Australia Australia

Pipeline Support, Stabilization and Protection

Submar

Swivel Joint Fluid Swivels Fmc Sofeco Floating Systems

Italy Traps Liquid Traps

Douglas Italia Spirax Sarco

Steam Traps Tlv Co Ltd Valve & Pump Packing

Mid Valley Bearing*

Welding Electrodes Bohler Electrodes & Wire Esab Weld Wire Redaeill Italy Weld wire and Electrodes Lincoln Electric USA Stick Welding Electrodes Kunci Quantum Sdn Bhd




Page 29 of 114


11. Fire Protection


CO2 System Carbon Dioxide Ansul Inc Kidde

Deluge valves Deluge Cla-Val Viking

Deluge valves Knowsley SK Fire and Gas Detection Fire and Gas Detection System Mircom Flame and Fire Detector Fenwal

POGC Fire Extinguisher Portable - Carbon Dioxide (5 kg) : Model # OU-8 Pozhtechnika Portable - Potassium Bicarbonate (9 kg)

Stored Pressure : Model # OP-10 Pozhtechnika

Portable

Ansul Inc Cosalt Chubb Fire Safety

Wheeled Ansul Fire Fighting Equipment Chubb Fire Safety

Knowsley SK Foam Skid

National Foam Quell Fire Safety

Fire Fighting Vehicle Hook-up Knowsley SK Fire Hose Angus

Chubb Fire Safety Knowsley SK Manuli National Fire Hose Potter-Roemer

Fire Hose & Nozzle Cabinet Knowsley SK Fire Nozzle Knowsley SK Fire Proofing Intumescent Coatings - Product: Thermo-lag Carboline Intumescent Coatings Chartek Intumescent Coatings - Product: Firetex Leigh's Paints Intumescent Coatings PittChar Fire Proofing Board and Metal Jacketing

Pittsburgh Corning FoamGlas Insulation

Firemans's Equipment GuardFire Ltd Knowsley Sk

Flame Arrestors Varec Gasous Fire Fighting System Topside

NK Co Ltd

GRE / FRP Pipe and Fittings Bondstrand Conley Corp Smith Fiberglass FIBERBOND

Hose Reel Chubb Fire Safety GuardFire Ltd

Hydrant Pillar Type Knowsley SK Mobile Fire Extinguisher Carbon Dioxide Knowsley SK Dry Chemical Knowsley SK Monitors Akron

Angus Elkhart




Page 30 of 114


Stang

Manual Foam Knowsley SK Oscillating Foam Knowsley SK Nozzle Akron

Angus Elkhart Stang

Portable Fire Extinguisher Carbon Dioxide Knowsley SK Dry Chemical - Stored Pressure and Cartridge

Operated (not specified in the documents which one was supplied)

Knowsley SK

Foam Knowsley SK Water Knowsley SK Skid Dry Chemical American Fire

Angus Ansul Inc Kidde

Foam Chubb Fire Safety Knowsley SK

Foam - Deluge Knowsley SK Fire Protection Engineering

Sprinkler Knowsley SK Twin Agents Skids American Fire

Ansul Inc Water Knowsley SK Water spray sprinkler systems Angus Watermist System Marioff

12. Life Safety


Accoustic Enclosures G&S Machining Stalfab Union Hydraulics

Air Pack Breathing Apparatus Model # 80411501 Scott Breathing System Delmo

SMC Eye Wash Station BOC Safety

Self-contained, gravity-fed : Model # 01104070

Encon

Fast Rescue Boat Alexander / Ryan Marine & Safety Co Norsafe AS Willard Marine

Fast Rescue Craft Davit Allied Marine Crane Fire Blanket Kit Model # SAF1000W Junkin Fire Stand Closed type

Includes: crowbar, spade, shovel, hook with wooden handle, pail, and wire rope cutting kit.

Pozhtechnika

First Aid Kit Includes bandages, medicinal, burn treatment, and eye treatment Model # 012101-2959

North

Life Float Billy Pugh Cosalt




Page 31 of 114


Hy-Grapha Jim Buoy Survival Systems International Viking Lifesaving Equipment Pte Ltd

Life Jackets Billy Pugh Cosalt

Hy-Grapha Safeguard Stearns Taylortec Viking Lifesaving Equipment Pte Ltd

Life Raft Inflatable Cosalt Viking Lifesaving Equipment Pte Ltd First Marine Service Sdn Bhd

Medical European Dental Center AEA International (Sakhalin) ZAO European Medical Center

Personal Protective Equipment DRC Sakhalin Group LLC ZAO Sakhalin Vostok Service

Ring Buoy Billy Pugh Cosalt

Hy-Grapha Jim Buoy Viking Lifesaving Equipment Pte Ltd

Safety Equipment Anchor Marine Transportation Ltd Seaward Safety Inc Unitor Ship Service (S) Pte Ltd Viking LifeSaving Equipment Bergen AS

Protective Clothing Can't Tear Em Global Safety Solutions & Mgt

Stair Treads J Blackwood & Son Safety Shower Hughes Safety Shower

International Medical Clinic K&D Pratt Ltd Keegan Speciality Enterprise Inc QMC (Quality Marketing Company) Silver Ships Inc Survival Systems International

Safety Shower & Eyewash Station

Model # 8710 Haws

Self-Contained Breathing Apparatus (SCBA)

Scott

Stretcher Basket type Model # 71 (stretcher), & 559 (brackets)

Ferno

Survival Craft Norsafe AS Survival Systems International

Survival Craft Assys and Components

Ropes and Winches Brucker Survival Systems Int.

Work Vests Billy Pugh Cosalt Hy-Grapha Steams Viking Lifesaving Equipment Pte Ltd




Page 32 of 114


13. Flare System


Flame Front Generator John Zink Company, LLC

Flare Systems Callidus

Flare Industries Inc

GBA Corona Inc

Hitachii Zosen Mechanical Corp

John Zink Company, LLC

Sam Shin Ind

Zeeco Inc Flare Systems Industrial Metallurgical Van Dam Flare Tip Package Callidus

Environmental Group P/L Motherwell Bridge John Zink Company, LLC John Zink Asia Pacific Kaldair Ltd NAO Roxar Victory International SA Zeeco Inc Mactronic

LP Flare Tip John Zink Company, LLC LP Tip Blower / Motor John Zink Company, LLC Miscellaneous Vent Tip & Snuffer Package GBA Corona Inc

14. I&C


Analyzers Automatic Sample System

SGS Redwood

BS&W Analyzer AGAR Endress & Hauser Faure Herman Invalco

Chromatographs Daniel Industries Rosemount Analytical

ABB Honeywell Ltd.

Corrosion Monitors

ClampOn AS CorrOcean Srl Fluenta AS Rohrback Cosasco Systems

Density Analyzer Micromotion Schlumberger Industries Solartron

ESD Analyzer Honeywell Ltd. F & G Detection Fire Detection Det-Tronics

Fire Eye Inc General Monitors Micropack Detection

Optical




Page 33 of 114


(Americas) Inc Kidde Fenwal

Honeywell Ltd. Pyrotronics (Siemens) Thermal & Smoke Sensors F & G Detection Gas Detection Det-Tronics

Gastech General Monitors Seiger Bacharach Simrad Optronics Draeger

Gas Detectors & Controllers

Gas Tech MSA (Mine Safety Appliance) Riken Keiki GX-7 Sieger

Gas Detectors (portable)

H2S in HC Analyzer

ABB Fluid System

Berthold Australia Rty Ltd Det-Tronics Foxboro General Monitors MSA Siegar Monitor Corporation Zellweger Analytics

Moisture Analyzer Ametek Instruments Dupont Endress & Hauser General Eastern Gruter & Marchand / Shaw Panametrics Inc PCI Div Rosemount Analytical

Oil-in-Water Analyzer

AGAR Bran+Luebbe, Inc Invalco Micromotion Segrist Segrist Teledyne Analytical Turner Design (Hydrocarbon Business Group) Western Research (Ametek) Hydril Haliburton Roxar MFI

Oxygen Analyzer Ametek Instruments Orbisphere Panametrics Inc PCI Div Rosemount Analytical Servomax Teledyne Analytical

Yokogawa

PH Meter & Conductivity Analyzer

Endress & Hauser Zellweger Analytics

Yokogawa

Sand Detector Analyzer

CorrOcean Srl Fluenta AS

Topside Particle ClampOn AS




Page 34 of 114


Monitor System

Water Cut Analyzer

Hydril

Water-in Oil Analyzer

AGAR Hach Loveland Halliburton Moriba Phase Dynamics Sigrist Wedgewood Delta C Technologies Inc

Flow Flow Metering Coriolis Micro Motion Inc. Flow Computers Daniel Industries OMNI

Spectra - Tek Solartron

Yokogawa Magnetic

Flowmeters Brooks Instruments Krohne Rosemount Foxboro

Honeywell Inc. Yokogawa

Multiphase Flowmeter

MPM (Multi Phase Meters) Schlumberger Industries Roxar ASA

Positive Displacement meters

American Meter Barton Instruments Brooks Instruments Faure Herman Smith

Turbine Meters Brooks Instruments NuFlo Smith Meter, Inc. Halliburton ITT Barton Faure Herman

Daniel Industries

Ultrasonic Flowmeter

Caldon Daniel Industries Fluenta AS Instromet Krohne Sick Mahaik

Siemens V cones McCrometer Variable Area

Meter ABB

Brooks Instruments Penberthy Rosemount Wallace & Tiernan

Vortex Flowmeters

ABB Honeywell Inc. Yokogawa

Endress & Hauser Foxboro Rosemount

Wetgas Meter MPM (Multi Phase Meters)




Page 35 of 114


Coriolis Meter Endress & Hauser Rheonik

Turbine Meters Faure Herman Ultrasonic

Flowmeter Panametrics

Flow Flow Regulator Atlantic Group Teknomax Yarway

Flow Switch Barton Instruments Fluid Components Intl (FCI) KDG Moberey Ball Delta Control/Pro-Quip Delavel/Barksdale Magnetrol

Flow Transmitters DP ABB Honeywell Inc. Yokogawa

Endress & Hauser Fisher Foxboro Rosemont

Flow Tubes, Venturies and Flow Nozzles

Daniel Industries

Leak Detection Equipment

ATMOS

Orifice Plates Fittings Berger Daniel Industries DAR En-Fab Inc Fluidic Techniques Oil and Gas Specialties Peco / Smith Meter Inc. Red Man Pipe and Supply SPM Triad Measurement ISA Controls

Meter Runs

Emerson Process Management

Pitot Tubes Averaging Pitot Tubes

Airflow Fisher KDG Moberey Mid-West Instrument

Sight Flow Brooks Instruments Daniel Industries Jacoby-Tarbox Jerguson Brookds Inst Div Magnetrol/AWC Penberthy Wallace & Tiernan W E Anderson/Wesco

Thermal Mass Electronics

Fluid Components Intl (FCI)


Emerson Process Management

Orifice Plates Fittings Daniel Industries Meter Runs


Dieterich Standard Inc




Page 36 of 114


Instrument Automation

DCS ABB Inc Honeywell Inc. Siemens Yokogawa

British Aerospace Foxboro MICC Emerson Process Fisher-Rosemount Division

Electronic Safety Shutdown

ABB Inc Honeywell Inc.

August Systems Hima ICS Triplex Moore Industries Inc. Triconex

PLC Allen Bradley Modicon

GE Siemens

SCADA Fisher Level Glass Level Gauge Jurgenson

Klinger Krohne K-Tek Nihon Klingage Penberthy TCVAL Penberthy Daniel

Level Gauge Magnetic Babbit International Jerguson K-Tek Magnetrol International Magnetrol International France MagTech Penberthy Tundra Controls Ltd

Radar Khrone Magnetrol International Ohmart / Vega Corp Rosemount Saab

Level Switch Float / Displacer Bestobell Fisher KDG Moberey Magnetrol International Masoneilan Division Static-O-Ring (SOR) Tokyo Keiso Co Ltd

Electric

Float / Displacer Fisher Pneumatic

Capacitance AGAR Magnetrol International

Level Switch Endress & Hauser Fisher Rosemount Magne-Sonics Magnetrol International Sensall Static-O-Ring (SOR)




Page 37 of 114


Level Transmitter Capacitance Drexelbrook Endress & Hauser Vega

DP Endress & Hauser Fisher Foxboro Magnetrol International Major Controls Rosemont Rosemont

Yokogawa Honeywell Inc. ABB

RF Probe Babbit International Krohne Magnetrol International

Sonic Kay-Ray Krohne Sensall

Nucleonic Berthold Austrailia Rty Ltd Nuclear Scanning Services

Float / Displacer Fisher Static-O-Ring (MSW) K-Tek ISA Controls Masoneilan

Pneumatic

Miscellaneous Alarm Systems Alarm Trips - Current Voltage

Dixon Moore Industries Inc.

Annunciator Panels

Bintek Ronan Engineering Zantek

Annunciators Riley - Panalarm Best Panalarm Ronan

Field Mounted Receivers

Indicator Dixon Dresser Instruments Division Foxboro

Electric Pneumatic Pneumatic

Pneumatic Controller

Fisher Non-Indicating

Fisher Foxboro Foxboro France SA Masoneilan

Indicating

Pneumatic Control Components

Axelson BWB Cal Con Versa

Recorder Barton Instruments Foxboro

Mechanical

Flame Arrestors Alsatec Groth Protectoseal Varec

Hand Switches Allen Bradley Schneider Electric - Square D

Hydraulic Power Unit

Basic Technologies Cooper Cameron Dynex / Rivett Inc




Page 38 of 114


Hydrostatic transducers

Ian Conrad Bergan Inc. Kongsberg-Autronica A/S Scana Electronics c/o AUM

Intrinsic Safety Barriers

Elcon Instruments MTL

Electronic ICS Triplex

Misc. Local Instrument Panels Surge/Capacity Compressor Controls Corp.

(CCC)

Automation USA Baker Brisco Engineering Fluides Service Hydrolex, Automated Controls Test Inc Texas Systems and Controls Inc TSI, Inc. W Industries RAN Puffer Sweiven Petrotech

Pig Signal ClampOn AS Fluenta AS Kidd Kidd Pipeline & Specialties Maloney Peco / Smith Meter Inc. T.D. Williamson, Inc.,

Meco Rupture Discs Anderson Greenwood /

Crosby Valve Fike Metal

BS&B

BS&B Safety Systems, Inc. Speed Switch Bentley Nevada

Tank vents Enardo Groth Protectoseal Shand & Jurs Varec

Terminal Blocks Phoenix Contact Weidmuller Klippon Entrelec

Tube Fittings Butech Turbo Mach

Enclosure Parker

Process Swagelok

Tubing Instrument Allegheny Ludium Alloy Metal & Tubes Autoclave Engineering Avesta Sheffield Carpenter Technology Sakai Sandvik Sumitomo Metal Industries, Ltd. TW Metals Thyssen




Page 39 of 114


Tubing Channel Channel Track J. C. White PW Industries

Vibration Monitoring

Amot Bentley Nevada Metrix Instrument Co. Robert shaw

Wellhead Control Panel

Automation USA Baker CAC Bumi Wangsa Sdn Bhd Mid South Controls and Services Petrotech Wormald Linott Oil and Gas Test Inc. Haven Automation

Frequency to Current Converter

Action Instrument Haliburton Moore Industries Inc.

Pressure Diaphragm Seal Dresser Instruments Division ITT

DP Indicators / Switches (Including Flow)

Custom Control Sensors Delta Controls Dresser Instruments Division Dwyer Instruments Inc. Fisher Geordin Mid-West Instrument NeoDyne Orange Research Inc Plenty Metrol Static-O-Ring (SOR)

Pressure Gauge Bourdori Rueger SA US Gauge WIKA Instruments

Pressure Manometer

Dwyer Instruments Inc. Meriam

Pressure Regulator

DP Cashco Endress & Hauser Fisher Masoneilan

Pnuematic Fisher

Process ABB Siemens

Fisher Masoneilan Taylor

Pressure Transmitters

Electronic (Direct & Diff)

ABB Yokogawa

Fisher Foxboro Rosemount Yamatake Custom Control Inc Static O Ring United Electric Honeywell Inc.

Transducers - P/I Rosemount




Page 40 of 114


Pressure Gauge Seintech / Wika DI Canada - Dresser Measurement Ashcroft Inc Ametek 3D Instruments Badotherm

Switch Electronic Custom Control Sensors Dresser Instruments Division ITT Barton NeoDyne Static-O-Ring (SOR)

Switch Pneumatic Fisher

Pressure Flowline Pilots Axelson BWB Controls Versa WKM

Temperature Temperature Assemblies

Berger Fisher Honeywell Inc.

Temperature Gauges

Dial Allesco Dresser Instruments Division Marsh Observator Rueger SA Tel-Tru US Gauge Ashcroft Inc

Temperature Gauges

Wika 3D Instruments Trend

Temperature RTDs DeGaussa (Sensycon) Rosemount Rueger SA Thermetrics Maverick Thermo Electric

Temperature Switches

Custom Control Sensors NeoDyne Static-O-Ring (SOR) Dresser Instruments Division United Electric Allen Bradley ASCO

Temperature Thermocouples

Rosemount

Temperature Transmitters

Electronic Rosemount Endress & Hauser Foxboro Rosemount Yamatake

Pneumatic Fisher Electronic ABB

Honeywell Inc. Yokogawa

Thermometers / Wells

Baro Controls Fisher Novatech Rawson and Co. Tel-Tru Transmark FCX Pty Ltd




Page 41 of 114


WIKA Instruments

Bi-Metallic Thermometers

Dresser Instruments Division

Valve Safety Valve Farris Engineering

Actuated ESD Valve

Bel Valves Cooper Cameron Valves Grove Valve and Regulator Malbranque Neles-Jamesbury PetrolValve Argus Borsig TK KVC (UK) Tyco Richards PCC KTM RBR VALVOLE ORSENIGO (FLUITEK) BREDA ENERGIA RING-O VALVE DELLA FOGLIA MIR VALVES

Automatic Recirculation Valves

Atlantic Group Keystone Yarway Schroedahl-Arapp Gmbh

Choke Valve Cameron Willis CCI Valve Cooper Cameron Valves Cor-Val Halliburton Hydril Introl (ABB) Masoneilan Master Flo Master Flo Mokveld Valves Bv. Shaffer Varco Best Willis Vonk Teledyne Merla Thornhill Craver

Cameron Willis Ireland Ltd Control Valve Ball Fisher

Kent (ABB) Masoneilan Mokveld Valves Bv. Ring-O

Butterfly Fisher Masoneilan Neles-Jamesbury

Globe Fisher Masoneilan Mokveld Valves Bv.

Eccentric Disk / Low Noise

Fisher Masoneilan Mokveld Valves Bv.




Page 42 of 114


PetrolValve Valtek

Motor Operated Dawler Raimondi WKM

Positioner Fisher Pnuematic Fisher

Masoneilan Valtek

Electropneumatic/Smart

Pressure Regulators

Fisher Cashco

Pump and Recirculation

Yarway

Shutdown Valves

Grove - Dresser Flow Control

Transducers (I/P)

Fisher Rosemont

Control Valve Dresser Flow Control Dresser Produits Industriels Fisher

Instrument / Tubing / Manifold

Anderson Greenwood / Crosby Valve Oliver Valves Ltd Parker Whitey

Injection Quill Oliver Valves Ltd

Limit Switch Fisher Westlock

Modulating Valves Fisher Pressure

Reducing Valve Daniel Industries

Fisher Grove Valve and Regulator Mokveld Valves Bv.

Pressure Relieving

Anderson Greenwood Brooks Instruments Daniel Industries Farris Engineering Mokveld Valves Bv.

Relief Conservation Vents

Anderson Greenwood Groth Varec

Pressure / Vacuum Vent

Anderson Greenwood Groth Shand & Jurs

Relief Safety Valve Anderson Greenwood Bailly-Birkett Crosby Tai Milano

Pilot Operated Relief Valves

Relief Safety Valve Axelson Brooks Instruments Daniel Industries Dresser Flow Control Mokveld Valves Bv. RSBD Sarasin Shand & Jurs

Bailey-Birkett Consolidated CCI

Spring Operated Relief Valves




Page 43 of 114


Crosby Farris Kunkle Tai Milano

Severe Service Valves

CCI Valve

Standard Control Valves

Dresser Produits Industriels

Solenoid Valve ASCO Versa IMF Honeywell - Skinner / Lucifer

Valve Actuator Axelson Baker Bernard Biffi Delta Controls EIM PetrolValve PALADON

Electric Limitorque Rotork

Hydraulic Flowserve/Valtek

Rotork Schafer (Emerson) Bettis Corporation Ledeen

Pneumatic (Piston)

Bettis Corporation Ledeen Rotork PALADON

Flowserve/Valtek

Pneumatic (Spring Return)

Bettis Prime Rotork Ledeen Limitorque Keystone Biffi PALADON

Valve Actuator Facilities

Dresser Flow Control Dupre Valves Puffer Sweiven Specialities Sunbelt Supply Valve Systems and Controls Wilson Valve Speciality Valser Engineering & Services Sdn Bhd

Isolation

Anderson Greenwood Astava Circle Seal Hoke Kenmac Marsh Nupro Precision General Whitey Oliver Blifold (Domino Series)




Page 44 of 114


15. Telecom


Tait

Access Control & CCTV Qatar Security Systems Aironet Antennas Antenna Cisco Antennas Microwave Andrew Corporation

Radiowaves RFS - Radio Frequency Systems

RF (& Accessories) Andrew Corporation Comrod PolyPhaser RFS - Radio Frequency Systems

VHF/UHF Jaybeam Cable Structured Cable System

(Voice & Data) ADC Krone

Antenna Cable Andrew Corporation UTP Belden RF Cablewave Fiber Optic Corning

Draka Alcatel-Lucent

Cable Fiber Optic, copper, panels, etc Siemon Closed Circuit Television System Production Monitoring Coex Ltd Production Monitoring, System / Exd

Cameras Hernis Scan Systems AS

Cameras Pelco Communication Console Motorola

Omnitronics Zetron

Communication Tower Alan Dick Allied Tower Andrew Corporation Eltel Networks (formerly TransMast) Rohn Tower Transmast

Converter B&B Electronics Entertainment System TVRO Applied Satellite Technology (Gardline

Group) Caprock Communications Sea Tel

Equipment Cabinets and Racks Chatsworth Rittal

Communications Console Omnitronics GMDSS - Global Maritime Distress and Safety System

Sailor

Liebert UPS Qatar Site & Power Meteorogical and Metocean System

Fugro

Data Acquisition Software Automasjon & Data AS NAVTEX Furuno Miros Wave Radar Miros A/S Offshore Muir Matheson Ltd Microwave Systems Alcatel-Lucent

Harris Stratex Harris / Farinon MDS (Microwave Data Systems)




Page 45 of 114


Motorola Sagem

UHF / Microwave Radios 4RF Communcations Network Equipment Wireless Ethernet Cisco Routers Cisco Switches Cisco Network Infrastructure Fiber Optic, copper, panels, etc ADC

CommScope General Cable Panduit Systimax Uniprise

Structured Cable System (Voice & Data)

Siemens

Offshore Loading System (Tanker) Telemetry

Bombardier Transportation

Outside Plant Manholes Pencell Polycom Video Conferencing Techno Q Public Address & General Alarm PA/GA Cable for Gaitronics only Amercable Speakers DNH A/S Federal Signal

Vodec Gai-Tronics Corp

Akusta Stentofon Le Las

Speaker/Beacons MEDC Fire Alarm Spector Lumenex Radar Systems Sperry Marine Collision Avoidance Furuno

Norcontrol Selesmar

Radio System UHF / Microwave Radios Alcatel-Lucent MDS (MicroWave Data Systems)

Aeronautical Icom Jotron

Marine (HF/VHF) Icom Operational (VHF/UHF) Motorola Trunked (VHF/UHF) Motorola Aeronautical - Base Station Park Air Radio Holland Pte Ltd Marine (HF/VHF) - Base Station Sailor Non-Directional Beacons Southern Avionics Satellite Handheld Phones Motorola

Thuraya Low Earth Orbit (LEO) Iridium Satellite Radio System Comm-Link Satellite Systems VSAT Caprock Communications

Schlumberger Stratos

Inmarsat B Nera Inmarsat C Sailor Inmarsat B, C, Fleet 55/77 Thrane Security Management Systems Gallagher Sensor Fence SOLAS/GMDS LIfeboat Radios Icom EPRIB's Jotron SARTS Jotron LIfeboat Radios Ratheon




Page 46 of 114


GMDSS - Global Maritime Distress and Safety System

Sailor

Subsea Fiber Tyco System Integrator Nessco

Omega Integration Page Europa ABB Inc-Oil & Gas Process Automation Able Communications Kentz

TransTel Engineering Pte Ltd Satellite/RF Caprock Communications RF Radio Holland Pte Ltd Test Equipment RF Anritsu

Bird Electronics Fluke Harris Progressive Electronics

Video Conferencing Equipment Polycom WIMAX (IEEE 802.16d/e) Motorola Wireless WAN (extended Ethernet) Proxim

ABB Caprock Communications Hermes Datacomm

Nova Communications

16. Electrical


Barriers Instrinsic Safety AWM Batteries and Chargers C & D Technologies DC Batteries C & D Technologies

Chloride Power GNB Saft Saft Singapore Pte Ltd. Yuasa Sonnenchein SEC Chloride C&D Technologies

DC Battery Chargers C&D Technologies Gutor Saft Fukuda Siemens Powertron / Powermatics LaMarche Solidstate Controls, Inc.

Battery Enclosure Container House International

Cable Marine shipboard cable AmerCable Balfour Beatty BIW Cable Furukawa Electric Prysmian LS-VINA Cable Rockbestos Suprenant Cable Corp




Page 47 of 114


Power and control cable AEI AWM Balfour Beatty Southwire Draka Kabel b.v. / Singapore Cable Manufacturer Draka USA Distribution BICC Ehlerskable Olex (Australia) Hitachi Pirelli General Power Cables Malaysia Sterling Greengate STK Alcatel AEI Kabel Metal Furukawa Electric Nexans Kerite Okonite Prysmian Hi-Essence Cable Sdn Bhd

Submarine Cable ABB Fujikura Ltd

J-Power Systems Nexans Prysmian General Cable

Cable Accessories Cable Glands Hawke ALCO BICC CMP Italsmea CMP Dunkerque Crouse-Hinds Surefit

Cable hanger Erico Jones(Stud) Nelson(Stud)

Conduit Hanger Grinnel Unistrut

Cable Runways Cable conduit Allied Tube and Conduit Alumax Easco Appleton Crouse-Hinds Occidental Coating(OCAL)

Cable Transits Hawke MCT Brattberg Ltd Grunau GmbH Nelson Roxtec

Cable Tray and Ladders AWM Cooper B Line Champion Fiberglass Enduro Orbtech Oglaend Systems Robroy Industries




Page 48 of 114


BICC Vantrunk GKN Husky Burndy Mono Strut Metal Perforators Swifts M Rack Unistrut VanTrunk Wiremold Cope Dynac Sdn Bhd

Distribution Boards Flameproof Appleton Crouse-Hinds Killark Nelson AWM

Ducting Low Voltage Bus AWM Busduct(Cast Resin) Low Voltage Bus Betobar Electrical / Instrument Building Square D

Merlin Gerin Consafe Lectrus Leirvik Emtunga AB ABB Point Eight Power Powell Industries, Inc.

Electrical Heater Chromalox Gas Heating Stiebel Eltron

Texas Systems Heatex

Generators Diesel Engine Generator Package Atlantic Caterpillar Cummins Engine Co Cummins Lae Singapore F. G. Wilson Mitsubishi Heavy Industry (M.H.I.) Mustang Power Systems Simpson Power Simpson Power General Electric Ideal Electric Kato (Reliance) Tractors Singapore Tractor & Equipment Nigeria Limited William Adams

Generators Large (>20 MW) Generators ABB Siemens / Westinghouse

Jeaumont Alstom

GE / Nuovo Pignone Generators Small (<20MW) Generators Hyundai Ideal

Taiyo Electric Co. Kato

Generators Thermo Electric Teledyne Generators Large (>20 MW) Generators Brush Turbogenerators

GE Furse Thermoweld Wallis Companies




Page 49 of 114


Burndy Cadweld

Heat Tracing AWM Raychem Thermon Far East Ltd Chemlex Thermon Heat Tracing Services

Heat Tracing System Tyco/Raychem/Tracer Heater Water Rheem HOA, Start/Stop Buttons, Switches Allen Bradley

A.T.X. Bartec Crouse-Hinds Appleton Killark Square D Telemencanique Stahl

Junction Boxes ABTech AWM Ceag Hammond Manufacturing Hoffman Rittal Stahl Tranberg Weidmuller Appleton Crouse-Hinds Killark Nelson Govan

Lighting Beacon / Rotating Crouse-Hinds Govan Hella

Emergency AWM Fittings Crouse-Hinds General AWM Lighting Fixtures Ceag

Chalmit Lighting Chalmit Lighting Crouse-Hinds Crouse-Hinds Glamox Glamox Medc Killark Hubbel Govan Simplex Lighting Stahl Appleton

Marine Pauluhn Convenience outlets Receptacles c/w Plugs Crouse-Hinds

Appleton Hubbell

Receptacles c/w Plugs(240 Vac) MK Motors DC General Electric




Page 50 of 114


Westinghouse AC/DC Brook Crompton

Parkinson Western Electric

Low Voltage Motors ABB WEG

Siemens Energy and Automation, Inc. Fuji Reliance Toshiba Teco Westinghouse

Siemens MV/HV voltage Electric motors ABB Teco Westinghouse

Alstom Siemens Energy and Automation, Inc. Mitsubishi Electric Reliance Toshiba US Motors

Siemens Submersible Franklin Electric Synchronous Motors ABB

Alstom Hyundai Ideal Mitsubishi Electric Electric Machinery Teco Westinghouse

Siemens GE Navigational Aids Pharos Marine Automatic Power

Automatic Power Orga Tideland Signal Corp

Aircraft Obstruction Lighting Orga Tideland Signal Corp

Page / Party System Gai-Tronics Corp Spector Lumenex

Power Transformers Alstom Merlin Gerin Brush Uptegraff Virginia Mitsubishi Electric Powell / ESCO AWM Brush Transformers Ltd

Dry Type ABB GE Siemens

France Transfo SGB-Starkstorm UIC (Exicast) Square D

Power Transformers Oil Filled ABB GE

Crompton Greaves Square D

Grounding Transformers GE




Page 51 of 114


Power Distribution Transformers ABB Protection Relay Basler

General Electric Westinghouse Multilin

Switchgear / Motor Control Centers Motor Control Centers ABB Alstom

Holec Cutler Hammer Allen Bradley Point Eight Power Powell Industries, Inc. Square D Merlin Gerin Switchgear & Instrumentation Ltd Vei Power Distribution (M) Sdn Bhd

Siemens Siemens Singapore

Switchgear ABB Switchgear & Instrumentation Ltd Schneider Electric General Electric Westinghouse SACE Vei Power Distribution (M) Sdn Bhd

Alstom Holec Point Eight Power Powell Industries, Inc. Square D Merlin Gerin Siemens Siemens Singapore

ABB Westinghouse Nelson International Switchboard

Terminal Blocks Phoenix Contact Weidmuller

Transfer Switch Automatic transfer switch, ATS ASCO Uninterruptible Power System Custom Power

Gutor Sab Nife Saft Nife Saft Singapore Pte Ltd. Merlin Gerin Ametek Solidstate Controls ABB Topaz Toshiba Solid state Control Inc(SCI) Yuasa Powermatrics(Malaysia) Powernetrics(UK) Thyrec Tegas Kombinasi Sdn Bhd Siemens

AC-UPS Systems Gutor DC Power Supply System Gutor Variable Frequency Drives LV Variable Fequency Drives ABB




Page 52 of 114


Allen Bradley Square D Telemencanique Cutler Hammer Toshiba

Robicon Siemens Variable Frequency Drives MV/HV Variable Fequency Drives ABB

Siemens Mitsubishi Electric

Allen Bradley Square D Telemencanique Toshiba

Robicon

17. Structural & Architectural


Insulation Dae Hyup Tech Neoprene Sheet Bakker

Bredero Trelleborg Bakker B.V. Trelleborg Hercules Trelleborg Viking

Steel Atlas Tube Grating Webforge Vic

Lionweld DAHE Industries

Deferco Clebecq Steel Plate

US Steel

JFE

Mitsui & Co. ThyssenKrupp Mannex GmbH

Mannesmann Owned by Salzgitter. Nippon Kokan

NKK Now JFE

Dillinger Hutte Nippon Steel Corp Kawasaki Steel Salzgitter Sumitomo Metal Industries, Ltd. Thyssen Stahlunion Corus Voest Alpine Posco

Steel Shapes Corus Kawasaki Steel Nippon Steel Corp Nippon Kokan (NKK) Sumitomo Metal Industries, Ltd. Arbed – Luxembourg

Structural Tubular and SMLS JFE




Page 53 of 114


Piles Sumitomo Metal Industries, Ltd. Nippon Steel Corp Nippon Kokan (NKK) Kawasaki Steel Mannesmann Corus Dalmine

Corus Structural Tubular and Piles

Sam Kang Industries ThyssenKrupp Mannex GmbH

Sumitomo Metal Industries, Ltd. Nippon Kokan (NKK) Nippon Steel Corp Osaka Tokushu KoKan (OTK) Berghor Eiserbau Kramer - Germany Westfalenwerke KG Mannesmann Graebener Preussag-Salzgitter Stahl Steel Flower - Korea

Spiral Welded Petropipe Industries

18. Marine


Acceptable Manufacturing


Boilers Exhaust Gas Economizers

Aalborg Industries A/S Aalborg Denmark, Singapore

Manufacturers - New Aalborg Industries A/S Aalborg Denmark, Singapore

Service / Repair / Rebuild

Combustion Control Systems

Gosfern Aalborg Denmark, Singapore


Harris Pye Singapore Thermal Fluid Heaters Aalborg Industries A/S Aalborg Denmark,

Singapore

Cargo Transfer Double Carcass Hose With Accessories

Yokahama Rubber Company Tokyo Japan

Bassi Offshore Gironico Italy

Telleborg Clemony-Ferrand France

Dunlop Oil & Marine Houston Texas, USA

Duel Product Swivel CALM Only Blue Water Energy

Services Houston Texas, USA

Loading Arms Loading Arms up to

16 inch Niigata Loading Systems, LTD

Niigata - Japan

Emco Wheaton Houston - Texas

Kirchhain - Germany

Loading Arms up to 20 inch FMC Technologies France

Marine Breakaway Coupling MIB International Ltd. Coventry England




Page 54 of 114


Gall Thompson Env. Ltd. Norfolk England Multi Product Swivel FSO / FSPO SBM Atlantia Houston Texas, USA

Blue Water Energy

Services Houston Texas, USA

SOFEC Inc Houston Texas, USA Poduct Swivel CALM Only SBM Atlantia Houston Texas, USA

Primary Emergency Release Coupling (PERC)

Up to 20 inches FMC Technologies France

MIB ITALIANA S.P.A. Padova - Italy Inert Gas Equipment


Air Products A/S Kristiansand Norway Hamworthy KSE Moss AS Singapore Mooring Equipment

Bardex Corporation Goleta California, Houston Texas

Bodewes Winches Mooring Equipment

Chain Jacks Imeca Groupe Perrotin La Rochelle France

Chain Jacks Smith Berger Marine, Inc. Seattle Washington USA

Mooring Equipment

Chain Stoppers Hull Only Aker Kvaerner Maritime Pusness AS

Arendal Norway

Mooring Equipment

Chain Stoppers Imeca Groupe Perrotin La Rochelle France

Smith Berger Marine, Inc. Seattle Washington USA

Harbor & Marine Engineering

Victoria Australia

Rolls-Royce Mooring & Deck Machinery

Houston Texas, USA

Mooring Equipment Chains Ramnas Bruk Bergslagen Sweden Rolls-Royce Mooring &

Deck Machinery Houston Texas, USA

Vicinay Cadenas SA Bilbao Spain Asian Star Anchor Chain Dongxing Town Chine Mooring Equipment

Fairleads Hull only Bardex Corporation Goleta California, Houston Texas

Mooring Equipment

Fairleads Aker Kvaerner Maritime Pusnes AS

Arendal Norway

Rolls-Royce Mooring & Deck Machinery

Houston Texas, USA

Mooring Equipment

Hawser & Accessories Bridon International Ltd. Doncaster England

Cosalt Safety & Production Lincolnshire England

Scanrope Tonsberg Norway Bexco Ropes Mamme Belgium Offspring International Inc. Laguna Niguel

California USA Mooring Equipment

Hawser Life Prediction Tension Technology Int. Ltd.

East Sussex England

Ocean Tech Systems Ltd. Surrey England Mooring Equipment

Hawser Tension Monitoring

Fugro GEOS Singapore

Ocean Tech Systems Ltd. Surrey England Harbor & Marine

Engineering Victoria Australia




Page 55 of 114


MSL Oilfield Services Ltd. Southampton England Strainstall Uk Ltd. Isle of Wight England Line Handling Boats Alnmaritec Ltd. Northumberland

England Mooring Sheaves Appleton Marine Appleton Wisconsin Mooring Equipment

Mooring Winches Appleton Marine Appleton Wisconsin

Imeca Groupe Perrotin La Rochelle France Norlau A/S Esbjerg Denmark Kocks Ostrava Hrabova

Czech Republic Rolls-Royce Mooring &

Deck Machinery Houston Texas, USA

Aker Pusnes Arendal Norway Mooring Equipment

Wire rope Hull Only Bridon Aberdeen England

Williamsport Wirerope Works Inc.

Williamsport Pennsylvania USA

Scanrope Tonsberg Norway Redaelli Wire Ropes Milano Italy Mooring Equipment

Hydralift Houston Texas USA

Mooring Equipment

Rolls-Royce Marine London England, Houston Texas USA

Pumping Systems

Deepwell Pumps Aker Kvaerner Eureka KOP

Arendal Norway

Framo Bergen Norway Hamworthy KSE Pump

Systems AS Singapore

Marflex BV Rotterdam The Netherlands

Misc. Pumps Framo Bergen Norway Pump Room Installation Hamworthy KSE Pump

Systems AS Singapore

Pump Room Installation Shinko Ind. Ltd. Hiroshima Japan Tank Venting Flame Arrestors Bolaco Valves ApS Nyborg Denmark Pres-Vac Engineering A/S Allerod Denmark High Velocity PV Valves Bolaco Valves ApS Nyborg Denmark Hankook Engineering Pte

Ltd. Singapore

Nakakita Seisakusho Co., Ltd.

Japan

Pres-Vac Engineering A/S Allerod Denmark

19. Surf (Marine)


J-Lay Collar Bruck Gmbh Dalmine Forgital Italy SpA Galperti Engineering & Flow Control SRL

J-Lay Collar Cladding Foure Lagadec Galperti Engineering & Flow Control SRL HD Cladding

Miscellaneous Components for Collars Artinox




Page 56 of 114


Mooring Equipment Umbilicals (Electrical / Hydraulic Cables)

Multiflex

Nitrogen Membrane Skid Chemitrol Offshore Related Export Line Buoyancy Element

Permanent & Temporary Belmar BMTI Trelleborg CRP Cuming Corp

Stab & Hinge Over Citba VIV Suppression Strakes Advance Products and Systems

Allbrown Universal Components Anglitemp Avon Technical Products Trelleborg CRP Dunlaw




Page 57 of 114


20. Forging Refer document below for list of acceptable manufacturers for forging

Forging Manufacturers EMDC Materials Group List of Qualified Forging List (QFL) According with MPDS 29-01-31

Rev. 3 – th November 2010

58 of 114

NOTES

1) EMDC requires that all critical carbon and alloy steel forgings shall be procured from qualified suppliers. The following product forms are covered by this Qualified Forging List:

• Tubing hangers

• Tubing head adapters

• Tree cap body

• Valve bodies, blocks and/or bonnets (see note 6 below)

• Connectors

• Choke bodies

• Manifold valve bodies and/or bonnets (see note 6 below)

• Taper joint forgings

• Flex joint forging

• Ball valves

2) This Qualified Forging List (QFL) identifies those forging manufacturers that have been technically assessed to supply forgings for onshore and offshore applications in accordance with MPDS 29-01-31

3) Manufacturers are qualified to supply the material grades, product forms, and sizes ranges as defined in the table.

4) Manufacturers are restricted to the restrictions shown and manufacturing processes shown under comments. A change shall invalidate

the manufacturer’s qualification.

5) Manufacturer shall have performed a technical audit of their sub-suppliers and details of this technical audit shall be made available to Company upon request.

6) EMDC accepts that certain manufacturing processes may be carried out by sub-suppliers. EMDC shall be advised if a change is made

which covers the following activities.

• Supply of raw material

• Forging

• Heat treatment

• Laboratory testing services

• N.D.E Services

7) QFL also includes forging manufacturers that have been used on previous Company projects. No information on performance or quality is available. Company has not endorsed these suppliers due to insufficient knowledge of suppliers quality. If Project desires to use these suppliers, then technical assessment is required.



59 of 114

8) Forging shaping operations may be performed by hammering, pressing, piercing, extruding, upsetting, rolling, bending or by a combination of all. Flanges, elbows, bends, tees, valve bodies, hangers, and/or manifolds shall not be machined directly from forged or wrought bar without written approval by Company.

9) If forgings have been purchased through a Stockist ( company who sub contracts processes to multi sub suppliers, and is also capable

of performing some manufacturing processes within). Stockist shall have performed a technical audit on their sub-suppliers and obtain appropriate Manufacturing Procedure Specification’s (MPS’s), which provides details of all critical operations performed on forgings being supplied for Company projects

10) It shall be the Stockists responsibility to ensure that sub-suppliers comply with the requirements of MPDS 29-01-31.

11) Details of technical audit reports along with MPS’s shall be made available to Company upon request. Under these circumstances,

Company reserves the right to carry out assessment of sub-suppliers in accordance with MPDS 29-01-31.

12) For general queries call Manuel Maligas ( + 1 281 654 5626) or Geoff Dunn ( + 1 281 654 4870) EMDC Materials Department. Greenspoint 6, Houston



60 of 114

Updated Rev No.

Manufacturer Location Product Forms Applicable Alloys

Restrictions Scope of Work

Howco Quality Alloys

Sheffield, UK Open die forgings (rolled ring, flanges, valves)

Carbon, alloy, stainless steels (F6NM, 410) and nickel alloys

Forging and bar stock. Forging are purchased from multiple sub-suppliers. Supply management company

Stockist purchases forgings from multiple sub suppliers. Capable of performing heat treatment, NDE and mechanical testing within.

Fomas Osnago, Italy Open die (valve bodies, shafts)

Carbon, alloy and stainless steels (F6NM, 410)

Forgings, < 40,000 kg Forging, heat treatment, NDE and mechanical testing performed within

ASFO Chiuppano, Italy Rolled rings Carbon and alloy Forgings, <9,000 Kg Forging, heat treatment, NDE and mechanical testing performed within

Ellwood Texas Forge

Houston Open die forgings (rolled ring, flanges, valves)

Carbon, alloy and stainless

Open die forgings <80,000 lbs, length 50 feet, diameter 90 inches

Melting, forging, heat treatment, NDE and mechanical testing performed within

Forgiatura Mame

Camuno, Italy Open die, shafts Carbon, alloy and stainless

Open die forgings 1,000-40,000 kg, length 15,000 mm, diameter 3,000 mm

Forging, heat treatment, NDE and mechanical testing performed within

Forgital Vicenza, Italy Rolled rings Carbon, alloy, aluminum, titanium

Rolled rings <3,000 mm diameter


Frisa Nuevo Leon, Mexico

Forged, seamless and rolled rings, flanges

Carbon, alloy, stainless and nickel base

Rings 10 kg – 40 tons, max diameter 8,000 mm


Gulfco Beaumont, Texas Rings, flanges, shape dies, discs, shafts


Rings – <36,000 lbs, open die forgings- 20,000 lbs


Metallurgica Siderforge

Cogollo del Cengio, Italy

Roll ring, open and close die forgings, valves

Carbon, alloy, and stainless

Ball valve forgings to 24 in, forgings 5000 kg, roll rings 2,500 mm OD x 200 mm ID


MetalCam Breno, Italy Open die forgings, flanges, shafts


Open Die forgings, <6,000 kg

Melting, forging, heat treatment, NDE and mechanical testing performed within. Thirty Five (35) ton melting facility in house

Updated Rev No

Manufacturer Location Product Forms Applicable Alloys Restrictions Scope of Work



61 of 114

Sheffield Forgemasters

Sheffield, UK Open die forgings Carbon, alloy and stainless

Bars and ingots for further processing

Melting facility

W F I Bonney Forge

Houston, Texas Open die flanges and fittings

Carbon and alloy Butt weld fittings, flanges


Custom Alloys High Bridge, NJ Open die, flanges and fittings

Carbon and alloy <250 kg Forging, heat treatment, NDE and mechanical testing performed within

MEGA Bergamo, Italy Piggable Y’s Carbon steel Piggable Y’s Subcontracts forging and heat treatment.

ASO Siderurgica Ospitaletto, Italy Bar Carbon, alloy and 3XX stainless steel with Carbon>.03%

Bars supplied only in non-heat treated condition

Supplier of bars in non heat treated condition to be re-forged or heat treated.

Ringmill Dubino, Italy Open die forgings, valves Carbon, alloy and stainless

<1,500 kg close die, <18,000 kg rings and <36,000 kg open die

Approved by reputation. Forging, heat treatment, NDE and mechanical testing performed within

Eastham Forge Beaumont Open die forgings Carbon, alloy and stainless

<13,000 kg Forging only

Riganti S.P.A. Solbiate Arno, Italy

Close die Carbon, alloy and Stainless

<500 Kg Forging, heat treatment, NDE and mechanical testing performed within

Lucchini RS Lovere (BG), Italy Open die Carbon, alloy and stainless

<15000 Kg Melting, forging, heat treatment, NDE and mechanical testing performed within.

Forge Fedriga Cividate Camuno, Italy

Open die Carbon, alloy and stainless


TD Forge Domaso Italy Open die Carbon, alloy and stainless


Forgerossi Italy Open die forgings Carbon, alloy and stainless

On AML

C.A.F. Spain Open die forgings Carbon, alloy and stainless

On AML

Melesi Italy Open die forgings Carbon, alloy & stainless

On AML




Page 62 of 114


21. Duplex Stainless Steel Refer document below for list of acceptable manufacturers for duplex stainless steel

Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers

Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011

63 of 114

NOTES

EMDC requires that all duplex and super duplex stainless steel materials shall be procured only from qualified suppliers. To become qualified, a

supplier must have satisfied the requirements of MPDS 29-01-04.

This Qualified Manufacturers' List (QML) identifies those suppliers that have been assessed in accordance with MPDS 29-01-04 and found

capable of supplying Duplex and Super Duplex material conforming to MPDS 29-01-02.

Manufacturers are qualified to supply the material grades, product forms, and sizes ranges as defined in the attached table.

Manufacturers are restricted to the use of the mandatory sub-suppliers listed in the attached table. A change in a mandatory sub-supplier shall

invalidate the manufacturer's qualification.

The following product forms are covered by this Qualified Manufacturing List:

- Bar (see note 7 below)

- Castings

- Fittings

- Forgings (see note 7 below)

- Induction Bends

- Plate

- Pipe (Seamless)

- Pipe (Long Seam Welded - not spiral welded pipe)

- Semi-finished Billet

Section sizes at final heat treatment in excess of 200 mm for 22 Cr duplex and 120 mm for 25 Cr super duplex are outside the scope of this

document and shall be subject to approval on a case by case basis.

Flanges, elbows, bends, plates, discs, tees, valve bodies, headers and manifolds shall not be machined directly from forged or wrought bar.

Forging shaping operations may be performed by hammering, pressing, piercing, extruding, upsetting, rolling, bending or by a combination of

two or more of these operations Small cylindrically shaped items may be machined from forged bar only with the express written approval of

ExxonMobil



64 of 114

The evaluation for acceptance shall include a visit to the manufacturers and, where necessary, sub-supplier's premises to review facilities, systems,

implementation of procedures and documentation as required by MPDS 29-01-04.

EMDC accepts that certain manufacturing processes may be carried out by a sub-supplier. Under these circumstances EMDC reserves the right to

carry out an assessment of mandatory sub-suppliers in accordance with MPDS 29-01-04. Also the supplier shall advise EMDC if there is a

change in any mandatory sub-supplier. Mandatory sub-suppliers will be those which cover the following activities

• Supply of raw material

• Supply of semi or part finished product

• Manufacturing processes such as forming, forging, casting and welding, including weld repair.

• Heat treatment

• Laboratory testing services.

• N.D.E. Services

During manufacture it shall be the manufacturer's responsibility to ensure that its sub-suppliers comply with the requirements of MPDS 29-01-02

and MPDS 29-01-04. Details of sub-suppliers will be made available to EMDC upon request.

The QML shall be revised and reissued to interested parties at frequency determined by EMDC.

EMDC shall monitor the performance of manufacturers and their sub-suppliers to ensure that the list of qualified manufacturer can be maintained.

The manufacturer and all sub-suppliers shall hold current accreditation to ISO 9000 or another recognized quality system acceptable to EMDC.

For general queries call Derek Horsburgh (+1 281 654 5507) or Bart Tarleton (+1 281 654 4960) EMDC, Materials Department, Greenspoint 6,

Houston.



65 of 114

Added / Updated Rev No.

Product Form (See Note 7)

Type of Material

Manufacturer

Standard and Grade

Qualified thickness/weight

Material form

Mandatory subcontractors & conditions

10 Bar 22Cr Foroni, Gorla Minore, (VA), Italy

A276 UNS S31803

200 mm No weight restriction

Wrought Bar

9 Bar 22Cr Sandvik, Sandviken, Sweden

A276 S31803 Production Route I: 20 - 75 mm OD Production Route II: 75 - 145 mm OD Production Route III 150 - 200 mm OD No weight restriction

Wrought Bar Production Route I; Final forming and heat treatment by Scana Soderfors AB

13 Bar 22Cr Scana Stavanger, Jorpelaan, Norway

A276 S31803 < 200 mm Diameter No weight restriction

Wrought Bar (Press Forged)

Base Material from Scana Stavanger Heat Treatment from Furnaces 112 and 113

13 Bar 22Cr BGH Edelstahl, Siegen, Germany


Forged Bar (Ingot Route)

Base Material from BGH Siegen Solution annealing in Furnaces 23, 24, 25, 26 and 27

14 Bar 22CR BGH Edelstahl, Freital, Germany

A276 S31803 < 64 mm Rolled Bar (Con cast)

Base material from BGH Freital Solution annealing in Furnace 474



66 of 114



Type of Material

Manufacturer

Standard and Grade


Material form



A276 S31803 < 200 mm Diameter




A276 S31803 < 121 mm Forged Bar (Con cast)



A276 S32760 < 120 mm Diameter














67 of 114



Type of Material

Manufacturer

Standard and Grade


Material form





8 Bar 25Cr Foroni, Gorla Minore, (VA), Italy

A276 UNS S32760 UNS S39277


Wrought Bar

14 Bar 25Cr Rolled Alloys Technology Limited, Blackburn, UK

A276 S32760 6.35 – 120 mm Wrought Bar Formerly Weir Materials

11 Bar 25Cr Sandvik, Sandviken, Sweden

A276 S32750 Production Route I: 20 - 75 mm OD Production Route II: 75 - 120 mm OD No weight restriction

Wrought Bar Production Route I; Final forming and heat treatment by Scana Soderfors AB

13 Bar 25Cr Scana Stavanger, Jorpelaan, Norway


Wrought Bar (Press Forged)

Material from Scana Stavanger Heat Treatment from Furnaces 112 or 113

13 Castings 22Cr Doncasters Paralloy Ltd, Billingham, UK

A890 Gr. 4A (UNS J92205)

t < 200 mm No weight restriction

Gravity sand Castings

Melt from 100% AOD – no returns or scrap added Heat treatment: In house or by ConMech Engineers Ltd. All weld repairs shall be solution annealed. FFS testing by Exova Teesside.



68 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


10 Castings 22Cr Fondinox, Sergnano, (Cr), Italy

A890 Gr. 4A (UNS J92205)

t< 130 mm No weight restriction

Centrifugal cast Balls


A890 Gr. 4A (UNS J92205)

t< 94 mm No weight restriction

Centrifugal cast Tubes


A890 Gr. 4A (UNS J92205)

t < 160mm No weight restriction


10 Castings 22Cr Norton Cast Products, Sheffield, UK.

A995 Gr. 4A (UNS J92205)

t < 134 mm Weight Unlimited


Heat treatment: By NCP or Special Steel Company Ltd., Sheffield, procedure NCP H/T 02. All weld repairs shall be solution annealed. Testing by MTT or another test lab acceptable to EMDC

9 Castings 22Cr Wm. Cook Hi Tec Integrity Castings, Parkway, Sheffield, UK

A890 Gr. 4A (UNS J92205)

t < 156 mm No weight limit

Sand Castings

Testing to be by an accredited external laboratory acceptable to EMDC.

14 Castings 22Cr Mathers Foundry Ltd, Manchester, UK

A 890 Gr 4A (J92205)


Gravity sand castings

Formerly Weir Foundries AOD starting material in-house, from Goodwins Steel Castings or Avesta Sheffield No revert / foundry returns

4 Castings 22Cr Brafe Engineering, Woodbridge, Suffolk, UK

A 890 Gr 4A (J92205)

T < 100 mm No weight limit





69 of 114



Type of Material

Manufacturer

Standard and Grade


Material form



A 890 Gr 4A (J92205)

T < 45 mm 18 kg max weight

Repliwax (Lost wax process)

Testing to be by an accredited external laboratory acceptable to EMDC

14 Castings 22Cr Goodwin Steel Castings,

SStoke on TTrent, UK

A 890 Gr 4A (J92205)



Testing in-house or at Exova Netherton, or Special Testing Labs, Sheffield. GSC’s image analysis system is acceptable for the determination of ferrite content.

6 Castings 22Cr Highland Foundries, Surrey, BC, Canada

A 890 Gr 4A T < 200 mm No weight limit


AOD Production route only

8 Castings 22Cr Furniss and White, Sheffield, UK

A890 Gr 4A (J92205)

T < 190 mm No weight restriction


New weld repair procedures to be qualified. Testing by CoMech, Derby or another test house acceptable to EMDC.

8 Castings 22Cr BEL Foundry, Newcastle, UK

A890 Gr 4A T < 115 mm Max weight 258 kgs


No major weld repairs allowed, all repairs shall be as welded. PMI by PMI Services Limited

8 Castings 22Cr Noel Village Steel Founders, Doncaster, UK

A890 Gr 4A T < 200 mm No weight restriction


Testing by CoMech Derby or another test house acceptable to EMDC. Heat treatment by Bodycote (formerly Expert Heat Treatments) of Stillington, Cleveland

9 Castings 22Cr MetalTek International, Pevely, MO

A890 Gr 4A T < 178 mm, No weight restriction


Heat Treatment in Furnace F1 Testing by St Louis Testing Laboratory or another test house acceptable to EMDC.



70 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


13 Castings 22Cr Bonds Precision, Alston, Cumbria

A995 Gr. 4A 100 mm max Gravity fed, Shaw ceramic process

Testing to be carried out by MIS Consett, or another laboratory acceptable to EMDC

9 Castings 25Cr Wm. Cook Hi Tec Integrity Castings, Parkway, Sheffield, UK

A890 Gr. 5A (UNS J93404)




13 Castings 25Cr Doncasters Paralloy Ltd, Billingham, UK

A890 Gr. 6A (UNS J93380)



Melt from 100% AOD – no returns or scrap added Heat treatment: In house or by ConMech Engineers Ltd. All weld repairs shall be solution annealed. FFS testing by Exova Teesside.


A890 Gr. 5A (UNS J93404)


Centrifugal cast Balls

All weld repairs shall be solution annealed.


A890 Gr. 5A (UNS J93404)


Centrifugal cast Tubes



A890 gr. 5A (UNS J93404)

t < 120mm No weight restriction





71 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


13 Castings 25Cr Mathers Foundry Limited, Manchester, UK

A890 Gr 6A (J93380)

t < 120mm, No weight limit


Formerly Weir Foundries AOD starting material in-house, from Goodwins Steel Castings, or from Avesta Sheffield. No revert / foundry returns

14 Castings 25Cr Goodwin Steel Castings, Stoke on Trent, UK

A 890 Gr 6A (J93380)



Testing in-house or at Exova Netherton or Special Testing Labs, Sheffield. GSC’s image analysis system is acceptable for the determination of ferrite content.


A 890 Gr 6A (J93380)





A 890 Gr 6A (J93880)

T < 45 mm 18 kg max weight

Repliwax (Lost wax process)


7 Castings 25Cr Highland Foundries, Surrey, BC, Canada

A 890 Gr 5A A 890 Gr 6A



AOD Production route only

8 Castings 25Cr Furniss and White, Sheffield, UK

A890 Gr 6A (J93380)

T < 120 mm No weight restriction


New weld repair procedures to be qualified. Testing by CoMech, Derby or another test house acceptable to EMDC.

8 Castings 25Cr Noel Village Steel Founders, Doncaster UK



Testing by CoMech Derby or another test house acceptable to EMDC. Heat treatment by Bodycote (formerly Expert Heat Treatments) of Stillington, Cleveland



72 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


13 Castings 25Cr Schmidt and Clemens, Lindar, Germany


Centrifugal Castings

Melting practice in accordance with Arbeitsanweisung 4300/38 Rev 1. Heat treatment in Furnace No 367. Hest treatment in accordance with Heat Treatment Instruction G 4470 and G4469 Rev 09/12/09. Testing by Schmidt and Clemens or another laboratory acceptable to EMDC. No weld repairs allowed


A995 Gr. 5A 62.5 mm max Gravity fed, Shaw ceramic process



A995 Gr. 6A 55 mm max Gravity fed, Shaw ceramic process


12 Castings 25Cr Norton Cast Products, Sheffield, UK.

A995 Gr. 6A (UNS J93380)

t < 125 mm Weight Unlimited


Heat treatment: By NCP or Special Steel Company Ltd., Sheffield, procedure NCP H/T 02. All weld repairs shall be solution annealed. Testing by MTT or another test lab acceptable to EMDC

13 Fittings 22Cr GAM Raccordi, Gazzola, (PC) Italy

A815 S31803 < = 60 mm 1/2 " - 20 " OD

Hot Formed Seamless from Pipe

MDS 01/DUPL/05 Base Material from DMV Montbard or Wyman Gordon, Livingston Heat Treatment from Furnace # 5



73 of 114



Type of Material

Manufacturer

Standard and Grade


Material form



A815 S31803 < = 60 mm 1/2" - 36" OD

Hot Formed Seamless from Trepanned Forged Bar

MDS 02/DUPL/05 Base Material from Forge Federiga, Foroni, Sandvik, Valbruna Heat Treatment from Furnace # 5


A815 S31803 < = 60 mm 6" - 48" OD

Hot Formed Seamless and Welded From Plate

MDS 03/DUPL/05 Base Material from Outokumpu (Degerfors) and Usinor (Fabrique de Fer and Le Creusot) Heat Treatment from Furnace # 5


A815 S31803 < = 35 mm 6" - 48" OD

Hot Formed Elbows Welded from Plate in Two Halves

MDS 04/DUPL/05 Base Material from Outokumpu (Degerfors) and Usinor (Fabrique de Fer and Le Creusot) Heat Treatment from Furnace # 5


A815 S31803 < = 13 mm 6" - 24" OD

Cold Formed Elbows Welded from Plate in Two Halves

QTR 05/DUPL/05 Base Material from Outokumpu (Degerfors and Avesta) and Usinor (Le Creusot) Heat Treatment from Furnace # 5

10 Fittings 22Cr Wilhelm Schulz, Krefeld, Germany

A815 S31803 t < = 31.75 mm (Caps up to 37.5 mm)

Seamless and Welded Cold Formed

Seamless pipe from DMV Montbard Plate from Thyssen Krupp, Outukumpu (Degerfors and KBR Mill) Final heat treatment in Wilhelm Schulz Krefeld Fittings Plant or at the Special Annealing Plant Hulserstrasse



74 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


6 Fittings 22Cr IBF, Piacenza Italy

A815 S31803 3 - 27 mm thick 4 to 60" OD

Hot formed welded fittings from plate.

Process Route 1 Base material from Thyssen, Avesta (Outokumpu) Sweden, Avesta (Outokumpu) Sheffield, Krupp, Fabrique de Fer (Industeel) Belgium, Ugine (formerly ALZ).


A815 UNS S31803

5 - 33 mm thick 4" to 24" OD

Hot Formed Seamless Fittings

Process Route 4 Base material from Tubacex, Sandvik, Schoeller-Bleckmann, SMTS Montbard and Costa Volpino (formerly DMV), Foroni/IBF Vittuone


A815 UNS S31803

2.7 - 18 mm thick Up to 16" OD

Cold Formed Fittings, Seamless and Welded

Process Route 5 Base material from: Seamless; Sandvik, Tubacex, Schoeller-Bleckmann, SMTS Montbard and Costa Volpino (formerly DMV), Foroni/IBF Vittuone Plate Thyssen, Avesta (Outokumpu) Sweden, Avesta (Outokumpu) Sheffield, Krupp, Fabrique de Fer (Industeel) Belgium, Ugine (formerly ALZ)



75 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


12 Fittings 22Cr SSE International, Dudley, UK

A815 UNS S31803

2.7 - 17 mm 1/2 to 8" OD

Cold Formed Seamless Fittings

Heat treatment in house. Testing, including PMI and FFS, by Exova, Netherton or another test house acceptable to EMDC. Intermediate stress relief solution anneal may be performed Base material from Tubacex, Schoeller-Bleckmann, Sandvik, DMV Montbard, DMV Costa Volpino This qualification relates to the material quality only and does not constitute an approval of the fitting design.

14 Fittings 25Cr Rolled Alloys Technology Limited, Blackburn, UK

A815 S32760 2.77 - 17.83 mm 0.5 - 8" NPS

Formerly Weir Materials


A815 S32760 3 - 24 mm thick 4" to 60" OD

Hot formed welded fittings from plate.

Process Route 1 Base material from Bohler, Industeel Creusot (formerly CLI), Outokumpu.


A815 S32760 14 - 24 mm thick 4" to 24" OD

Hot Formed Seamless Fittings

Process Route 4 Base material from Industeel Creusot (formerly CLI), Foroni/IBF Vittuone



76 of 114



Type of Material

Manufacturer

Standard and Grade


Material form



A815 S32760 2.7 - 9 mm thick Up to 16" OD

Cold Formed Fittings, Seamless and Welded

Process Route 5 Base material from: Seamless; Tubacex, Schoeller-Bleckmann, Foroni/IBF Vittuone Plate Bohler, Outokumpu, Industeel Creusot and Belgium




Seamless pipe from Sandvik, Sandviken, Plate from CLI (Le Creusot) and Bohler, Kapfenberg Final heat treatment in Wilhelm Schulz Krefeld Fittings Plant or at the Special Annealing Plant Hulserstrasse



77 of 114



Type of Material

Manufacturer

Standard and Grade


Material form





Seamless pipe from DMV Remscheid and Schoeller Bleckmann, Ternitz. Plate from CLI (Le Creusot) and RA Materials (Formerly Weir Materials) Limited (Manufacturing Works Number C25739902 only) Final heat treatment in Wilhelm Schulz Krefeld Fittings Plant or at the Special Annealing Plant Hulsertrasse


A815 S32750 T < = 11 mm ½” – 8” OD


QTR 01/750/05 Seamless Pipe from Sandvik, Sandviken Heat Treatment from Furnace # 5


A815 S32750 < = 38 mm 2" - 36" OD

Hot Formed Seamless and Welded Fittings from Plate

QTR 02/750/05 Plate from Outukumpu Degerfors and Industeel (Creusot) Heat Treatment from Furnace # 5


A815 S32750 < = 32 mm 4" - 36" OD

Hot Formed Seam Welded Elbows from Two Halves From Plate

QTR 03/750/05 Plate from Outukumpu Degerfors and Industeel (Creusot) Heat Treatment from Furnace # 5



78 of 114



Type of Material

Manufacturer

Standard and Grade


Material form



A815 S32760 < = 23 mm ½” - 8" OD


QTR 01/760/05 Seamless Pipe from SMTS Montbard France Heat Treatment from Furnace # 5


A815 S32760 < = 40 mm ½” - 24" OD

Hot Formed from Hollowed Forged Bar

QTR 02/760/05 Forged Bar from: Brietenfeld, Mitterdorf, Germany Pipe from Forged Bar from: IBF Vittuone / Foroni, Italy Heat Treatment from Furnace # 5


A815 S32760 < = 32 mm 2" - 36" OD

Hot Formed Fittings from Plate Rolled and Welded with 1 Seam

QTR 03/760/05 Plate from: Thyssen Krupp Nirosta and Industeel (Creusot) Heat Treatment from Furnace # 5


A815 S32760 < = 34 mm 4" - 36" OD

Hot Formed Seam Welded Elbows from Two Halves From Plate

QTR 04/760/05 Plate from: Thyssen Krupp Nirosta;Industeel (Creusot); Bohler Bleche Heat Treatment from Furnace # 5

12 Forgings 22Cr Forgiatura Marcora Srl, Olgiate Olona (VA) Italy

A182 F 51 (UNS S31803)


Rings Open die Forged

Heat treatment by Sorbit furnace islands F6 or F10 Base material Cogne, Valbruna, Aceria de Alava Testing by Sigmatre or another test house acceptable to EMDC



79 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


14 Forgings 22Cr Inoxfucine, Montanaso, (LO), Italy

A182 F 51 (UNS S31803)

d < 120 mm g < 451 kgs

Open Die Hammer Bars

Billet from Aceralava, Cogne & Foroni Manufacturing Specification MS130/G


A182 F 51 (UNS S31803)

d < 200 mm No weight restriction

Free Forging Press Bars



A182 F 51 (UNS S31803)


Free Forging Press Rings

Billet from Aceralava, Cogne & Foroni Manufacturing Specification MS133/G or 134/G


A182 F 51 (UNS S31803)


Free Forging Press Discs



A182 F 51 (UNS S31803)


Open Die Press Nozzles

Billet from Aceralava, Cogne & Foroni Manufacturing Specification MS141/G or 142/G


A182 F 51 (UNS S31803)


Free Forging Press Flat Bar




80 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


7 Forgings 22Cr Melesi, Cortenove, Lecco, Italy

A182 F 51 (UNS S31803)

T<200 mm T<64 mm T<120 mm T<200 mm T<104 mm No weight restriction

Open Die Pressed and Ring Rolled Open Die Hammer Open Die Pressed Closed Die Hammer Closed Die Press Forged

Billet materials from Techphy, ABS Safau, Aceralava, Foroni, Sandvik, Cogne, Industeel (Creusot), Outokumpu (Degerfors), Trinecke Zelezarny.



81 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


14 Forgings 22Cr Spromak, Liverpool, UK

ASTM A182 Gr F51 (UNS S31803)

Max t = 82 mm Max weight = 25 kg

Closed Die Forged

Forging by Dyform-Jenkins-Dunn. Note Spromak also use fully forged and heat treated items from Abbey Forge Sheffield. Heat Treatment by Darlington Heat Treatment Testing by Exova Netherton, Salford or Tees-side or another test laboratory acceptable to EMDC Material from Valbruna Aceralava, Cogne, BGH Freital, Foroni, Sandvik, Outokumpu and Olara This qualification relates to the material quality only and does not constitute an approval of the fitting design.

1 Forgings 22Cr Bruck, Ensheim, Germany

ASTM A182 F51 (UNS S31803)

38 to166 mm. Contour Forged and/or Ring Rolled

Billet from Foroni, Cogne and Bohler

2 Forgings 22Cr Ringmill, Dubino (SO), Italy

ASTM A182 F51 (UNS S31803)

T < 200 mm T < 200 mm T < 200 mm

Closed Die Open Die + Ring Rolled Open Die

All billet from Foroni. Open and Closed Die forging by press forging.

8 Forgings 22Cr Eastham Forge, Beaumont, TX

ASTM A182 F51 (UNS S31803)

200 mm No max weight restriction

Open Die / Hammer / Press

Billet from Atlas Steel, Canada or from Foroni, Italy



82 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


5 Forgings 22Cr Metallurgica Siderforge, Cogollo del Cengio, (VI), Italy

ASTM A182 F51 (UNS S31803)

T < 196 mm T < 200 mm T < 200 mm

Closed Die Open Die + Ring Rolled Open Die

Billet from Cogne, Valbruna or ABS Safau. Open and Closed Die forging by press forging. See report for full range of approval.

6 Forgings 22Cr ASFO, Chiuppano, (VI), Italy

ASTM A182 F51 (UNS S31803)

200 mm Open die + Ring Rolled

Billet from Cogne, Foroni and Aceralava Metallography at Lab San Marco or another laboratory acceptable to EMDC.

14 Forgings 22Cr FEAT, Cesana Brianza, (LC), Italy

ASTM A182 F51 (UNS S31803)

T < 81 mm Up to 7 kgs

Closed Die Press Forged

Testing by Sigmatre or another laboratory acceptable to EMDC. Final heat treatment to be carried out by Sorbit. Billet from Acciaierie Valbruna

13 Forgings 22Cr Stooss, Hedingen, Switzerland

ASTM A182 F51 (UNS S31803)

T < 190 T < 135 T < 38

Open die pressed Open die pressed and ring rolled Hammer forged and ring rolled

Billet from Foroni or Bohler. Metallographic testing at Exova Crema, SMT Pozzo d’Adda, or another laboratory acceptable to EMDC



83 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


14 Forgings 22Cr Galperti s.r.l., Cortenova, Lecco, Italy

ASTM A182 F51

200 mm max No weight restriction

Closed die, press forged; Closed die press forged and ring rolled

Heat treatment in furnace H2 and in tank number HTT2 Testing by AQM, Sigmatre or another laboratory acceptable to EMDC. Base material from Cogne or Sandvik

13 Forgings 22Cr Special Quality Alloys (SQA), Sheffield, UK

A182 F51 (UNS S31803)

T< 200 (was 150) mm No max. weight restriction

Open Die Hammer; Blanks and Rings

Billet from Foroni, Cogne, Sandvik, Scana, or BGH. Heat Treatment in Furnace No. 7 at Special Steels Forging by, IFA Limited Sheffield, Forge UK, Sheffield or Special Forged Products Limited Sheffield. Testing by Special Testing Limited or another laboratory acceptable to EMDC.

13 Forgings 22Cr Howco Quality Alloys / Howco Metals Management, Sheffield,

ASTM A182 F51

200 mm Pressed and / or Hammer Forged

Heat treatment in Howco Sheffield, Furnaces number 1 and 7. Testing at Howco Sheffield except metallographic examination which shall be at Exova Tees-side or another lab acceptable to EMDC. F51 base material from Foroni or BGH Siegen



84 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


13 Forgings 22Cr Clydesdale Forge, Hartlepool, UK

ASTM A182 F51

108 mm max 36.8 kg max. per forging

Closed die, hammer forged

Heat Treatment by Darlington Heat Treatments, Newton Aycliffe Mechanical and corrosion testing by Caparo Testing Technologies, Hartlepool, or another test house acceptable to EMDC Not pickled – items to be fully machined or pickled by others PMI and FFS by a laboratory acceptable to EMDC Base material from Valbruna (Vicenza / Bolzano) or Outokumpu (Degerfors)

13 Forgings 22Cr MEGA-Isma, Italy

ASTM 182 F51 78 mm max 24 kg max per forging

Closed die, press forged

Heat treatment according to procedure NOR001 at Sorbit furnace island F10. Testing in house; at Sigma Tre, Garbagnate Monasterio; corrosion testing by Quality Control Mediolago; or another laboratory acceptable to EMDC. Base material from Valbruna, Vicenza. Sandvik, Olarra or Cogne This qualification relates to the material quality only and does not constitute an approval of the fitting design.

13 Forgings 22Cr Hans van Triel, Essen, Germany

ASTM A182 F51

Open die 200 mm

Open die hammer forged Free formed ring forged

Base material from Aceralava, Outokumpu (Degerfors), BGH (Siegen), Bohler, Cogne. Heat Tretament in Furnace number 5 to Procedure HvT 2/2-035. PMI by others. Testing by Germanischer Lloyds, Herne or another test lab acceptable to EMDC.



85 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


13 Forgings 22Cr MSI Quality Forgings, Doncaster, UK

ASTM A182 F51

200 mm

Open Die, Hammer Forged

Base material from Aceralava Mechanical testing by TEI Wakefield or another test lab acceptable to EMDC

13 Forgings 22Cr Fratelli Risetti, Solbiate Arno (VA), Italy

ASTM A182 F51

106 mm 60 kg max per forging

Closed Die, Hammer

Base material from Valbruna or Ugitech This qualification relates to the material quality only and does not constitute an approval of the fitting design.

14 Forgings 22CR WFI International, Houston Texas, USA

ASTM A182 F51


Closed Die Pressed

Base material from Outokumpu, Richburg, SC, Foroni or Valbruna, Vicenza Testing in house or by Accu-Test or Exova, Houston. Heat treat in house in Furnace #s 483, 489 or 499 or by Specialty Heat Treatment Houston, Furnace #s 200, 203, 253 or 257. FFS by CDJ Services Houston This qualification relates to the material quality only and does not constitute an approval of the fitting design.

14 Forgings 22Cr Abbey Stainless, Sheffield, UK

ASTM A182 F51


Open Die Hammer

MPS ASS 05-08 Base Material from Aceralava Forging by Forge UK Heat Treatment at Metal Treatment UK Furnaces # 1 and 2 Testing by Metal Testing UK Analysis by Sheffield Testing



86 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


10 Forgings 25Cr Fomas, Osnago,(LC), Italy

A182 F53 (UNS S32750)

t < 120 mm

Cylindrical free form forgings


A182 F 55 (UNS S32760)

T < 120 mm No max. weight restriction

Press free forged. (Discs)

Billet from Cogne Manufacturing Procedure MS97/G


A182 F 55 (UNS S32760)

T < 120 mm g < 225 kg

Open Die Press (Nozzles)

Billet from Cogne Manufacturing Procedure MS87/G


A182 F 55 (UNS S32760)

T < 120 mm No max weight restriction

Free Forging Press Flat Bar

Billet from Cogne, Aceralava, Foroni Manufacturing Procedure MS144/G


A182 F 55 (UNS S32760)

T < 120mm No max. weight restriction

Free Forging Press and Ring Rolling Rings



A182 F 55 (UNS S32760)

T < 120 mm No max weight restriction

Free Forging Press Discs


14 Forgings 25Cr Rolled Alloys Technology Limited, Blackburn, UK

UNS S32760 1' 150# to 16" 900# Max Wall = 120mm

Flanges and hubs

Only sizes tested during qualification are accepted. Formerly Weir Materials

2 Forgings 25Cr Ringmill, Dubino (SO), Italy

ASTM A182 F55 (UNS S32760)

T < 120mm T < 120 mm

Open Die + Ring Rolled Closed Die

All billet from Foroni Open and Closed Die forging by press forging.



87 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


6 Forgings 25 Cr ASFO, Chiuppano, (VI), Italy

A182 F53 (UNS S32750)

120 mm Open die + Ring Rolled

Billet from Avesta Degerfors Metallography at Lab San Marco or another laboratory acceptable to EMDC


A182 F55 (UNS S32760)

T< 120 mm T<60mm T<120 mm T< 120m T< 91m


Cogne, Acciaerie Valbruna, Bohler, Aceralava, Foroni,



88 of 114



Type of Material

Manufacturer

Standard and Grade


Material form



A182 F53 (UNS S32750)

T< 120 mm T<60mm T<120 mm T< 120m T< 91m


Cogne, Sandvik, Acciaerie Valbruna,

13 Forgings 25Cr Stooss Hedingen, Switzerland

A182 Gr F55 (UNS S32760)

T < 120 T < 116

Open die pressed Open die pressed and ring rolled

Billet from Foroni or Aceralava. Testing at Exova Crema, SMT Pozzo d’Adda or another laboratory acceptable to EMDC



89 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


13 Forgings 25Cr Special Quality Alloys (SQA), Sheffield, UK

A182 F53 (UNS S32750) A182 F55 (UNS S32760)

T<80 mm T<120 mm

Open Die Hammer; Blanks and Rings

S32750 Billet from Sandvik. S32760 Billet from Foroni, Cogne, Scana, or BGH. Heat Treatment in Furnace No 7 at Special Steels Forging by IFA Limited Sheffield, Forge UK, Sheffield or Special Forged Products Limited, Sheffield. Testing by Special Testing Limited or another laboratory acceptable to EMDC.

8 Forgings 25Cr Bruck, Ensheim, Germany

ASTM A182 Gr F55 (UNS S32760)

T< 120 mm. Contour Forged Billet from Bohler



90 of 114



Type of Material

Manufacturer

Standard and Grade


Material form



ASTM A182 F53 (UNS S32750)


Closed Die Forged

Forging by Dyform-Jenkins-Dunn. Spromak also use fully forged and heat treated items from Abbey Forge Sheffield. Heat Treatment by Darlington Heat Treatment Heat Treatment by Darlington Heat Treatment Testing by Exova Netherton, Salford or Tees-side or another test laboratory acceptable to EMDC Material from Sandvik This qualification relates to the material quality only and does not constitute an approval of the fitting design.


ASTM A182 F55 (UNS S32760)


Closed Die Forged

Forging by Dyform-Jenkins-Dunn. Spromak also use fully forged and heat treated items from Abbey Forge Sheffield. Heat Treatment by Darlington Heat Treatment. Heat Treatment by Darlington Heat Treatment Testing by Exova Netherton, Salford or Tees-side or another test laboratory acceptable to EMDC Material from Bohler, Valbruna, BGH Freital, Cogne, Foroni, Scana Stavanger or Aceralava. This qualification relates to the material quality only and does not constitute an approval of the fitting design.



91 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


12 Forgings 25Cr Forgiatura Marcora Srl, Olgiate Olona (VA) Italy

A182 F 53 (UNS S32750)


Discs Open die forged

Heat treatment by Sorbit furnace islands F6 or F10 Base material Cogne, Valbruna, Aceria de Alava Testing by Sigmatre or another test house acceptable to EMDC


ASTM A182 F53



Heat treatment in furnace H2 and in tank number HTT2 Testing by AQM, Sigmatre or another laboratory acceptable to EMDC. Base material from Cogne or Sandvik


ASTM A182 F55



Heat treatment in furnace H2 and in tank number HTT2 Testing by AQM, Sigmatre or another laboratory acceptable to EMDC. Base material from Foroni


ASTM A 182 F53

Open Die 120 mm


Base material Heat treatment in Furnace number 5 to procedure HvT 2/2-030. PMI by others. Testing by Germanischer Lloyds, Herne or another test lab acceptable to EMDC.



92 of 114



Type of Material

Manufacturer

Standard and Grade


Material form



ASTM A182 F55

Open Die 120 mm


Base material from Heat treatment in Furnace number 5 to procedure HvT 2/2-027. PMI by others. Testing by Germanischer Lloyds, Herne or another test lab acceptable to EMDC.




Heat treatment according to procedure NOR001 at Sorbit furnace island F10. Testing in house; at Sigma Tre, Garbagnate Monasterio; corrosion testing by Quality Control Mediolago; or another laboratory acceptable to EMDC. Base material from Sandvik, Sandviken. This qualification relates to the material quality only and does not constitute an approval of the fitting design.




Heat treatment according to procedure NOR001 at Sorbit furnace island F10. Testing in house; at Sigma Tre, Garbagnate Monasterio; corrosion testing by Quality Control Mediolago; or another laboratory acceptable to EMDC. Base material from BGH Freital. This qualification relates to the material quality only and does not constitute an approval of the fitting design.



93 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


13 Forgings

25Cr

Howco Quality Alloys / Howco Metals Management, Sheffield,

ASTM A182 F55

IFA Route 100 mm Forge UK Route 120 mm

Pressed and / or Hammer Forged

Heat treatment in Howco Sheffield, Furnaces number 1 and 7. Testing at Howco Sheffield except metallographic examination which shall be at Exova Tees-side or another lab acceptable to EMDC. Base Material from Foroni or BGH Siegen

13 Forgings 25Cr MSI Quality Forgings, Doncaster, UK

ASTM A182 F55

120 mm Open Die, Hammer Forged

Base material from Scana Stavanger Mechanical testing by TEI Wakefield or another test lab acceptable to EMDC

13 Forgings 25Cr SBP Metals Technology, Sheffield, UK

ASTM A182 F55

120 mm Open Die Press and Hammer Forged

Forging by Forge UK (Production Route AG F002) Heat treatment by QHT Rotherham, Furnace number 1. Testing at MTT Sheffield Base Material from Scana Stavanger


ASTM A182 F53


Closed Die, Hammer

Base material from Sandvik, Sweden This qualification relates to the material quality only and does not constitute an approval of the fitting design.



94 of 114



Type of Material

Manufacturer

Standard and Grade


Material form



ASTM A182 F55


Closed Die, Hammer

Base material from Valbruna or BGH Freital This qualification relates to the material quality only and does not constitute an approval of the fitting design.

14 Forgings 25CR WFI International, Houston Texas, USA

ASTM A182 F55


Closed Die Pressed

Base material from Rolled Alloys Technology, Blackburn, UK; BGH Siegen, Germany Testing in house or by Accu-Test or Exova, Houston. Heat treat in house in Furnace #s 483, 498 or 499 or by Specialty heat Treatment Houston, Furnace #s 200, 203, 253 or 257. FFS by CDJ Services Houston This qualification relates to the material quality only and does not constitute an approval of the fitting design.

14 Forgings 25Cr Abbey Stainless, Sheffield, UK

ASTM A182 F55


Open Die Hammer

MPS ASS 06-08 Base Material from Scana Stavanger Forging by Forge UK Heat Treatment at Metal Treatment UK Furnaces # 1 and 2 Testing by Metal Testing UK Analysis by Sheffield Testing



95 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


13 Induction Bends

22Cr Proclad - IBS, Glenrothes, UK

UNS S31803 Not applicable; test bend to be run as per MPDS 29-01-07

Induction bent pipe, seamless and welded

Heat treatment:- internal (using Furnaces 1, 2 or 3 at Glenrothes) or by ConMech, Consett, Co.Durham, Testing by M.I.S. Livingston or Consett, Co.Durham, or another laboratory acceptable to EMDC PPM required for each PO; Materials Group shall be in attendance

14 Induction Bends

25Cr Proclad - IBS, Glenrothes, UK



Heat treatment:- internal (using Furnaces 1, 2 or 3 at Glenrothes) or by ConMech, Consett, Co.Durham, Testing by M.I.S. Livingston or Consett, Co.Durham, or another laboratory acceptable to EMDC PPM required for each PO; Materials Group shall be in attendance

13 Induction Bends

22Cr Induction Pipe Bending (IPB), Sunderland, UK



Heat treatment by Conmech, Co Durham Testing in-house or at another lab acceptable to EMDC. PPM required for each PO; Materials Group shall be in attendance



96 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


13 Induction Bends

25Cr Induction Pipe Bending (IPB), Sunderland, UK



Heat treatment by Conmech, Co Durham Testing in-house or at another lab acceptable to EMDC. PPM required for each PO; Materials Group shall be in attendance

13 Induction Bends

22Cr SIMAS, Prezzate-Mapello, Italy


Induction bent pipe, seamless and welded pipe

Testing by SMT, Pozzo d’Adda, or another laboratory suitable to EMDC PPM required for each PO; Materials Group shall be in attendance

13 Induction Bends

25Cr SIMAS, Prezzate-Mapello, Italy


Induction bent pipe, seamless and welded pipe

Testing by SMT, Pozzo d’Adda, or another laboratory suitable to EMDC PPM required for each PO; Materials Group shall be in attendance

14 Induction Bends

22Cr Fabricom, Grimbergen, Belgium



Testing by Stork Intermes, Berchem, or at another lab acceptable to EMDC. PPM required for each PO; Materials Group shall be in attendance



97 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


14 Induction Bends

25Cr Fabricom, Grimbergen, Belgium



Testing by Stork Intermes, Berchem, or at another lab acceptable to EMDC. PPM required for each PO; Materials Group shall be in attendance

0 Plate 22Cr Outokumpu, Hot Rolled Plate Division - Degerfors, Sweden

A240 S31803 t = 6 - 50 mm Hot rolled plates

Heat treatment in batch furnace: "Norm-ugn". Formerly Avesta Polarit AB, Hot Rolled Plate Division

7 Plate 22Cr Outokumpu, KBR Mill, Avesta, Sweden

A240 S31803 3.00 to 13.00 mm Hot Rolled Forced Air Cooled Formerly Avesta Polarit


A240 S31803 1.50 - 6.35 mm

Cold Rolled Forced Air Cooled Formerly Avesta Polarit

14 Plate 22Cr Bohler Bleche, Murzzuschlag, Austria

A240 S31803 / S32205

1.50 – 76.2 mm Hot Rolled MPS FPP01/2010 Rev 00 Slab from Bohler Edestahl Kapfenberg G48 and Fischer Ferritescope by Bohler Edelstahl, Kapfenberg Final heat treatment in furnace Neuss # 4121



98 of 114



Type of Material

Manufacturer

Standard and Grade


Material form



A240 S32750 1.50 - 6.35 mm Cold Rolled Water Quenched Formerly Avesta Polarit

14 Plate 25Cr Duplex

Rolled Alloys Technology, Blackburn, UK

UNS S32760 1.5 – 92 mm thick Formerly Weir Materials


A240 S32750 1.50 – 50.0 mm Hot Rolled MPS FPP 03/2010 Rev 00 Slab from Bohler Edestahl Kapfenberg G48 and Fischer Ferritescope by Bohler Edelstahl, Kapfenberg Final heat treatment in furnace Neuss # 4121


A240 S32760 1.50 – 50.0 mm Hot Rolled MPS FPP 02/2010 Rev 00 Slab from Bohler Edestahl Kapfenberg G48 and Fischer Ferritescope by Bohler Edelstahl, Kapfenberg Final heat treatment in furnace Neuss # 4121

13 Seamless Pipe

22Cr SMST France Montbard, France

A790 S31803 t < = 20.6 mm NPS<=8"

Direct hot extrusion

Base material from SMTS Germany in Remscheid and from Montbard in France Formerly DMV Montbard

13 Seamless Pipe

22Cr SMTS Italy, Costa Volpino, (BG), Italy

A790 UNS S31803

Up to 5 mm thick, NPS<=2"

Cold Pilgered Base material from SMTS Germany in Remscheid and from Montbard in France Formerly DMV Costa Volpino



99 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


10 Seamless Pipe

22Cr Sandvik Steel, Sandviken, Sweden

A790 UNS S31803

Hot Finished <= 22.83 mm th. Cold Finished <= 10.23 mm th.

All material to be water quenched. Sandviken Plant, Sweden

10 Seamless Pipe

22Cr Schoeller Bleckmann, Ternitz, Austria

A790 UNS S31803

Max t = 22.83 mm MaxOD = 168.28 mm Max t = 12.5 mm Max OD = 88.9 mm Max t = 15.63 Max OD = 104.00

Production Route 1 (Hot and Cold Formed) Production Route 2 (Cold Pilgered) Production Route 3 (Cold Drawn)

Base material from Tubacex Spain

11 Seamless Pipe

22Cr Tubacex Tubos Inoxidables, Llodio, Spain

ASTM A 789 UNS S31803 ASTM A790 UNS S31803

Route 1: 31.75 mm max Route 2: 15.88 mm max Max OD = 8 inch

See Mandatory subcontractors & conditions

Route 1: Hot finished, direct water quenching Route 2: Hot finished, continuous furnace heat treatment. Base Material from Aceralava



100 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


2 Seamless Pipe

22Cr Wyman Gordon, Livingston, UK

A790 S31803 12 < t < 94 mm 200 < OD < 900 mm

Extruded Pipe Note pipe of wall thickness up to 160 mm may be produced. See report for qualification status of this material.

6 Seamless Pipe

22Cr Sumitomo, Amagasaki Mill, Japan

A790 S31803 Up to 7" OD Up to 17.8 mm thick

Hot Extruded Pipe

6 Seamless Pipe

22Cr Sumitomo, Wakayama Mill, Japan

A790 S31803 Up to 7 to 12" OD Up to 26.7 mm thick

Hot forging / rolling / piercing (Mannesman Process)

6 Seamless Pipe

22Cr IBF, Vittuone, (MI) Italy

A790 S31803 18 - 36 mm thick 4 - 24" OD

Seamless Pipe (from hot forged bar to A182)

Process Route 6 Base material from Foroni Heat treatment furnace No 8 (Calibrated in accordance with API 610 Appx. H.)



101 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


10 Seamless Pipe

25Cr Schoeller Bleckmann, Ternitz, Austria

A790 UNS S32760

Max t = 22.83 mm MaxOD = 168.28 mm Max t = 12.5 mm Max OD = 88.9 mm Max t = 15.63 Max OD = 104.00

Production Route 4 (Hot and Cold Formed) Production Route 5 (Cold Pilgered) Production Route 6 (Cold Drawn)

Base material from Tubacex Spain

13 Seamless Pipe

25Cr SMST France Montbard, France

A790 UNS S32760

t < = 20.6 mm NPS<=8"

Direct hot extrusion

Base material from SMTS Germany in Remscheid and from Montbard in France Formerly DMV Montbard

13 Seamless Pipe

25Cr SMTS Italy, Costa Volpino, (BG), Italy

A790 UNS S32760

Up to 7.9 mm thick, NPS<=2"

Cold Pilgered Base Material from SMTS France in Montbard Fornerly DMV Costa Volpino

14 Seamless Pipe

25Cr Rolled Alloys Technology Limited, Blackburn, UK

A790 S32760 2.77 - 21.95 No weight restriction




102 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


10 Seamless Pipe

25Cr Sandvik, Sandviken, Sweden

A790 S32750 Hot Finished <= 13.71 mm th. Cold Finished <= 10.23 mm th.

All material to be water quenched. Sandviken Plant, Sweden

6 Seamless Pipe

25Cr IBF Seamless Pipes, Vittuone (MI) Italy

UNS S32760 14 - 27 mm thick 4 - 24" OD

Seamless Pipe (from hot forged bar to A182)

Process Route 6 Base material from Foroni Heat treatment furnace No 8 (Calibrated in accordance with API 610 Appx H.)

10 Seamless Pipe



Route 1: 22.83 mm max Route 2: 13.91 mm max Route 3: 10.93 mm max Max OD = 8 inch


Route 1: Hot finished, direct water quenching Route 2: Hot finished, continuous furnace heat treatment. Route 3: Cold finished, continuous furnace heat treatment. Base Material from Aceralava



103 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


14 Seamless Pipe



Route 1: 27.44 mm max Route 2: 19.05 mm max Route 3: 8.93 mm max Max OD = 8 inch


Route 1: Hot finished, direct water quenching Route 2: Hot finished, continuous furnace heat treatment. Route 3: Cold finished, continuous furnace heat treatment. Base Material from Aceralava

5 Semi Finished Billet

22Cr Valbruna Acciaierie, Vicenza and Bolzano, Italy

UNS S31803 Not Applicable

Semi finished billet for re-processing by others

5 Semi Finished Billet

25Cr Valbruna Acciaierie, Vicenza and Bolzano, Italy

UNS S32760 Not Applicable Semi finished billet for re-processing by others

10 Welded Pipe (LSW)

22Cr Outokumpu, Fagerstad, Sweden

A928 UNS S31803

2-4" Sch10S Formerly AST (Avesta)


22Cr Outokumpu, Storfors, Sweden

A928 UNS S31803

Cl 1, 25 mm max, Cl 3, 7.12 mm max, Max Dia = 610 mm

Formerly AST (Avesta) Heat treatment in roller hearth furnace only. Plate from Outokumpu Degerfors or Avesta



104 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


8 Welded Pipe (LSW)

22Cr Butting, Knesebeck, Germany

A928 S31803

2 - 36" 1.6 - 50 mm

Plate from Avesta KBR, Avesta Degerfors, Thyssen Krupp Nirosta, Industeel Arcelor (Fabrique de Fer), Industeel Arcelor (Le Creusot)

7 Welded Pipe (LSW)

22Cr Erndtebrucker Eisenwerke (EEW), Erndtebruck, Nr Siegen, Germany

A928 UNS S31803

8mm wt to 28 mm wt 6 - 60" OD

Welded Pipe The level of cold work after solution annealing to be restricted to 1% maximum. Testing by sub contract laboratory acceptable to EMDC. Plate from Avesta Degerfors or Fabrique de Fer Heat treatment by EEW or by Schulz in Krefeld, Germany.


22Cr InoxTech Lendinara, Italy

A928 UNS S31803

t = 10 - 60 mm Welded Pipe Heat Treatment in Furnace H Base materials from, Outukumpu (Degerfors), Thyssen Krupp, Industeel (Le Creusot and Fabrique de Fer) All repair welds shall be solution annealed


25Cr Rolled Alloys Technology Limited, Blackburn, UK

A928 S32760 NPS 6 - 30" Wall Thickness 3.76 - 31.75


8 Welded Pipe (LSW)

25Cr Butting, Knesebeck, Germany

A928 S32760 8 - 36" 2.7 - 44 mm

Plate from, Avesta KBR, Avesta Degerfors, Thyssen Krupp Nirosta, Bohler.



105 of 114



Type of Material

Manufacturer

Standard and Grade


Material form



25Cr Outokumpu, Storfors, Sweden

A928 UNS S32750

Cl 1, 18.75 mm max, Cl 3, 5.71 mm max Max Dia = 610 mm

Formerly AST (Avesta) Heat treatment in roller hearth furnace only. Plate from Outokumpu Degerfors or Avesta



A928 UNS S32750

t = 10 – 40 mm Welded Pipe Heat Treatment in Furnace H Base materials from, Outokumpu (Degerfors), Thyssen Krupp, Industeel (Le Creusot and Fabrique de Fer) All repair welds shall be solution annealed



A928 UNS S32760

T = 6 – 32 mm Welded Pipe Heat Treatment in Furnace H Base materials from, Outokumpu (Degerfors), Thyssen Krupp, Industeel (Le Creusot and Fabrique de Fer) All repair welds shall be solution annealed

13 Umbilical Tubing

25Cr Sandvik Precision Tubes, Chumotov, Czech Republic

A789 S32750 1.00 < t < 4.93 mm 11.0 < OD < 46.00 mm

Extruded Seamless Tube

Hall 1 Heat Treatment in RODR 1000 Furnace Line Base material originally melted in Sandvik Sweden (Sandviken). Extruded Hollows from Sandvik Sweden, Sandvik India (Rajpur) and Sandvik, Scranton USA (Scranton)

13 Umbilical Tubing


A789 S32750 1.00 < t < 5.00 mm 11.0 < OD < 31.10 mm


Hall 1 Heat Treatment in RODR 2000 Furnace Line Base material originally melted in Sandvik Sweden (Sandviken). Extruded Hollows from Sandvik Sweden, Sandvik India (Rajpur) and Sandvik, Scranton USA (Scranton)



106 of 114



Type of Material

Manufacturer

Standard and Grade


Material form


13 Umbilical Tubing


A789 S32750 1.00 < t < 2.68 mm 11.0 < OD < 30.00 mm


Hall 2 Heat Treatment in Drever Furnace Line Base material originally melted in Sandvik Sweden (Sandviken). Extruded Hollows from Sandvik Sweden, Sandvik India (Rajpur) and Sandvik, Scranton USA (Scranton)

10 Umbilical Tubing

25Cr Sandvik, Sandviken Sweden

A789 S32750 2.90 < t , 6,6 mm 50 < OD < 108.5 mm

Extruded Seamless Tubes

Centre Tubing Only Heat Treatment in Furnace USAB 326 RV63 Pickled finish



107 of 114

Qualified Independent Test Laboratories The laboratories on this list have been qualified to carry out the testing required by MPDS 29-01-02. For testing outside the scope of this specification please contact EMDC Materials.

Added /

Updated

Rev #

Laboratory Name Location and Contact Details Notes

14 Accu-Test 7821 Pinemont, Houston, TX, 77040, USA

+1 713 460 3655

www.accutest-labs.com

14 AQM Via Edison 18, 25050 Provaglio d’Iseo, (Brescia), Italy

+39 030 9291711

www.aqm.it

14 CoMech Castings Road, Derby, DE23 8LY, UK

+44 1332 867 700

www.comech.co.uk

14 Exova Edinburgh, UK Lochend Induxctrial Estate, Newbridge, EH28 8PL, UK

+44 131 333 4360

www.exova.com

Formerly Bodycote

14 Exova Houston, USA 9925 Regal Row, Houston, TX, 77040, USA

+1 281 848 0270

www.exova.com

Formerly Bodycote



108 of 114

14 Exova, Crema, Italy Via dalla Pierina 9/11, Crema, (CR), Italy

+39 0373 89721

www.exova.com

Formerly Bodycote

14 Exova Karlskpga, Sweden Gammelbackavägen 6, Box 431, Karlskoga, 691 27

+46 (0)586 810 55

www.exova.com

Formerly Bodycote

14 Exova Dudley, UK 182 Halesowen Road, Netherton, West Midlands, UK

+44 1384 455 751

www.exova.com

Formerly Bodycote

14 Exova Tees-side, UK Holwick Road, Riverside Park, Cleveland, TS2 1QS, UK

+44 1642 250 336

www.exova.com

Formerly Bodycote

14 Exova Bridgewater, UK No 1, Festival Units, The Showground Business Park, Bridgewater, TA6 6LS, UK

+44 1278 456 888

Formerly Bodycote

14 Exova Sandnes, Norway Luramyrveien 69, PO Box 1084, Sandnes, Norway

+47 51 709 690

Formerly Bodycote

14 Germanischer Lloyds, Germany Südstraße 59, 44625 Herne, Germany

+49 02325 637969-0

www.gl-nobledenton.com/en/Herne.php

14 Metals Testing UK Beeley Wood Lane

+44 114 231 8805

www.theabbeygroupuk.co.uk



109 of 114

14 M.I.S. Consett, UK Eden House, Watling Street industrial Estate, Leadgate, Co Durham, DH8 6TA,

UK+44 1207 599 260

www.mistesting.co.uk

14 M.I.S. Livingston, UK Unit 5a, Telford Square Business Park, Houston Industrial Estate, Houston Road,

Livingston, EH10 5PQ, UK

+44 1506 432 203

www.mistesting.com

14 M.T.T. Sheffield, UK Metals Technology Testing Ltd, Finchwell Close, Sheffield, S13 9D, UK

+44 114 243 7271

www.metalstechnology.co.uk

14 SigmaTre, Italy Via Fornace 31, 23846 Garbagnate Monasterio, (Lecco), Italy

+39 031 87 94 25

www.sigmatre.it

14 S.M.T. Italy Via del Lavoro 7, 20060 Pozzo d’Adda, (Mi), Italy

+39 02 909 67 142

www.smtsrl.com

14 Special Testing Limited, UK Bacon Lane, S9 3NH, UK

+44 114 244 1061

www.specialtesting.co.uk

14 St. Louis Testing Laboratory, USA 2810 Clark Avenue, St. Louis, MO, 63103, USA

+1 314 531 8080

www.labinc.com



110 of 114

14 T.E.I. Ltd. UK Po Box 80, Calder Vale Road, Wakefield, West Yorkshire, WF1 5YS, Wakefield,

UK

+44 1924 780000

www.tei.co.uk/metallurgical-laboratory.php




Page 111 of 114


22. Upstream Acceptable Manufacturers of Structural Plate, Shape and Tubular Products

Refer to TS 29-01-09: Upstream Acceptable Manufacturers of Structural Plate, Shape and

Tubular Products.




Page 112 of 114


Record of Change

Rev 1 Date: Apr

2011

Location Action Description

Section 6 Addition Added the following manufacturers in Unfired Pressure Vessel category:

- Petra Fabricators - Jutasama - AMC

Section 9 Deletion Deleted Dalmine from the Low Chrome up to 13% and Alloy, SS, Monel

and etc category as it is not approved in the EMDC QSL list

Section 17 Deletion Deleted Perwaja Steel Sdn Bhd from Structural & Architectural – Steel

Plates

Section 20 Addition Addition of Section 20 - Qualified Forging List

Section 21 Addition Addition of Section 21 - Qualified Suppliers List for Duplex Stainless

Steel

Section 22 Addition Addition of Section 22 - Acceptable Manufacturers of Structural Plate,

Shape and Tubular Products)

Rev 0 Date: Nov

2010

Location Action Description

Initial Publish.

Instituted Purpose Codes [X], [Y], [Z] to identify those paragraphs that

have been deleted ( [X] ), modified ( [Y] ), or added ( [Z] ) as a result of

the Gap Analysis undertaken to identify items in heritage EMEPMI

design documentation (DIM and GS) and other sources relevant to

EMEPMI operations (i.e. Regulatory requirements) that should be

included into the MPDS.

Those paragraphs with Purpose Codes [X], [Y], [Z] shall be compared

against subsequent revisions of the GPs as they are accepted into

EMEPMI.




Page 113 of 114


Attachment: Purpose Codes Definitions

Code Description

C Assigned to paragraphs containing specifications whose primary purpose is reduced costs.

Reduced cost in this context refers to initial investment cost and does not include Life-Cycle

cost considerations. Life-Cycle cost considerations are captured under reliability,

maintainability, or operability purpose codes.

E Assigned to paragraphs containing specifications whose primary purpose is driven by

environmental considerations. Environmental considerations typically include specifications

intended to protect against emissions/leakage to the air, water, and/or soil. Deviations from the

specifications contained in such paragraphs require formal review and approval according to

local environmental policy.

I Assigned to paragraphs that provide only clarifying information such as Scope statements,

definitions of terms, etc.

M Assigned to paragraphs containing specifications whose primary purpose is to provide for

maintainability of equipment or systems. Maintainability provisions are those that facilitate the

performance of maintenance on equipment/systems either during downtimes or during on-

stream operations.

O Assigned to paragraphs containing specifications whose primary purpose is to assure

operability of equipment or systems. Operability is the ability of the equipment/system to

perform satisfactorily even though conditions are off-design, such as during start-ups, process

swings, subcomponent malfunction, etc.

R Assigned to paragraphs containing specifications whose primary purpose is to improve or

assure the reliability of equipment or systems. Reliability is a measure of the ability of

equipment/systems to operate without malfunction or failure between planned maintenance

interventions.

S Assigned to paragraphs containing specifications whose primary purpose is avoidance of

personnel or operational safety incidents. Any deviation from the specifications contained in

such designated paragraphs requires formal review and approval according to local safety

policy.

Personnel Safety: Refers to the avoidance of recordable personnel injuries; i.e., burns, cuts,

abrasions, inhalation, or exposure to dangerous substances, etc., that

could result in medical treatment, restricted work, lost-time incidents, or

fatalities.

Operational

Safety:

Refers to the prevention and control of process releases, fires, explosions,

etc.




Page 114 of 114


Code Description

X Assigned to paragraphs that have been deleted in their entirety from the GP base-document,

and not replaced when developing the MPDS. The associated Rationale content has been

deleted as appropriate. The statement “Intentionally Deleted” has been added to the original

GP item number to retain the GP base-document structure.

The GP base-document and revision are listed on the front page of this MPDS as well as all

page footers.

The deleted paragraphs and requirements therein were not applicable to the MPDS at the time

of MPDS development. Subsequent revisions of the GP shall be compared against this

MPDS to ensure that GP updates are properly incorporated into the next revision of the

MPDS, including a review of deleted paragraphs to ensure the deletion is still valid.

Y Assigned to paragraphs that have been modified from the GP base-document when developing

the MPDS. These modifications may include partial deletion of text from a specific

requirement. The changes identified are of a technical nature, affecting the clause of the

MPDS (compared to the GP base-document). Clerical changes, such as replacement of "GP"

with "MPDS" or "Company" with "EMEPMI" are not identified.


page footers.

Specific project requirements have been written into the GP base-document paragraph.

Subsequent revisions of the GP shall be compared against this MPDS to ensure that GP

updates are properly incorporated into the next revision of the MPDS. The specific project

requirements embedded in the GP base-document paragraphs shall be retained in subsequent

revisions of the MPDS unless otherwise superseded by requirements in the GP. Alternately,

they may be removed via the appropriate deviation process.

Z Assigned to paragraphs that have been added to the GP base-document.


page footers.

The paragraph numbers assigned shall add onto the GP base-document structure. Therefore,

subsequent revisions of the GP shall be compared against this MPDS to ensure that GP updates

are properly incorporated into the next revision of the MPDS. All additional paragraphs in this

MPDS shall be included in subsequent revisions of the MPDS unless otherwise superseded by

requirements in the GP. Alternately, they may be removed via the appropriate deviation

process.

Documents

MPDS 00-99-01 Rev_1 (2011)