MyWindFit

Page 1 of 12 Contents subject to change Instructions_mywindfit_mounting revision 00

Mounting your MyWindFit Meter The MyWindFit Kit and Plus products include two mounting accessories, a universal bicycle mount and an armband

mount. Each mounting type securly fastens the Meter and allows it to be adjusted to ensure optimal performance.

Universal Bicycle Mount

Zip strap

Sensor Mount

Rubber pads

MyWindFit

Page 2 of 12 Contents subject to change Instructions_mywindfit_mounting revision 00

1. Determine desired mounting position

Front Fork

Under handlbar

MyWindFit

Page 3 of 12 Contents subject to change Instructions_mywindfit_mounting revision 00

2. Adjust the position of the Meter mount

IMPORTANT – Do not over-tighten. Finger tight only

Loosen

Tighten

Adjust

MyWindFit

Page 4 of 12 Contents subject to change Instructions_mywindfit_mounting revision 00

3. Secure the mount to the bicycle

IMPORTANT – When mounting on the bicyle forks, make sure the rubberized

section is fulley contacting the fork to ensure maximum security.

Rubber pads

Front

Pull tight

Trim

MyWindFit

Page 5 of 12 Contents subject to change Instructions_mywindfit_mounting revision 00

4. Install Meter and make final adjustments, see Adjusting Position of Meter below

IMPORTANT – Do not over-tighten. Finger tight only

IMPORTANT – Meter white stripes should be facing straight forward

Tighten

MyWindFit

Page 6 of 12 Contents subject to change Instructions_mywindfit_mounting revision 00

Adjusting the position of the meter

To ensure the MyWindFit meter measures the full wind speed, it must be positioned

Meter

Direction of travel

90 degrees

90 degrees

Meter

Ground

MyWindFit

Page 7 of 12 Contents subject to change Instructions_mywindfit_mounting revision 00

Troubleshooting

Symptom Possible Solutions Bicycle mount is not staying secure

to the bike

1. Verify that the rubber pad is fully contacting the bike 2. Install additional rubber pad shipped with the mount. 3. Pull the zip strap tighter

The zip strap is not staying secure 1. Press the zip strap latch tab down (when strap is removed) 2. Add zip ties as necessary.

I trimmed the zip strap too short

1. Use electrical zip ties to secure the mount

MyWindFit

Page 8 of 12 Contents subject to change Instructions_mywindfit_mounting revision 00

Armband Mount

1. Assemble armband

IMPORTANT – Do not over-tighten. Finger tight only.

Make sure the silver attachment nut is facing the velcro buckle

Arm Band

Sensor mount

Thumb screw

MyWindFit

Page 9 of 12 Contents subject to change Instructions_mywindfit_mounting revision 00

2. Install MyWindFit Meter

IMPORTANT – Do not over-tighten. Finger tight only

3. Place armband mount on your arm (left or right), position the band either below or above your bicep, close to

your elbow or shoulder.

IMPORTANT – MyWindFit meter white stripes should be facing straight forward

MyWindFit

Page 10 of 12 Contents subject to change Instructions_mywindfit_mounting revision 00

4. Wrap armband around your arm and secure Velcro

5. Insert Velcro strap through the plastic loop and tighten

MyWindFit

Page 11 of 12 Contents subject to change Instructions_mywindfit_mounting revision 00

6. If necessary, make final adjustments. The Meter should be facing directly forward and straight up and down. The

armband mount will rotate 360 degrees and lock in-place.

Push to lock

MyWindFit

Page 12 of 12 Contents subject to change Instructions_mywindfit_mounting revision 00

Troubleshooting

Symptom Possible Solutions

The arm band slips down when I train

1. Ensure the silver attachment nut is facing forward 2. Ensure both Velcro straps are snug 3. Position the strap above or below your bicep

The Meter rotates back and forth when I

train

1. The 360 degree mount is not locked in-place, push the tab to

lock

SEE THE FAQ SECTION OF THE MYWINDFIT WEBSITE FOR MORE