Upload
lyhanh
View
216
Download
1
Embed Size (px)
Citation preview
8-80High quality microwave and millimeterwave components and subsystems. Visit Ducommun Technologies online at www.ducommun.com.
Motion Detector Modules
FEATURESHigh reliabilityHigh sensitivity CW and pulse operation Low harmonic emissionCompact sizeLow cost and volume productionMeet FCC, PTT, FTZ and DTI regulations
Intrusion alarmAutomatic door openerSpeed measurementContact less vibration measurementTraffic signal actuatorAutomatic illumination system
APPLICATIONS
SMD series K band Motion Detector Modules are designed for short-range motion/speed detection where the cost is essential. The modules are constructed with a T/R diplexer, a single ended mixer and a frequency and power adjustable Gunn diode oscillator. The module uses the low cost die-cast housing to further reduce the manufacturing cost while maintain a ridged mechanical configuration. The integrated design offers compact size and ease system integration. The dual channel version is available per request.
DESCRIPTION
SPECIFICATIONS
Bulletin No. SMD
SMD Series
Typical Specifications
Parameters CW (Model No.: SMD-240912CW-02) Pulse (Model No.: SMD-240912PS-02)RF frequency 24.150 GHz 24.150 GHz
Transmitter output power +8.5 dBm (typical) +8.5 dBm (typical)Receiver conversion loss 12 dB (typical) 12 dB (typical)
IF bandwidth DC to 100 MHz (minimum) DC to 100 MHz (minimum)Operation Voltage 4.5 to 5.5 Vdc 6 to 8.5 Vdc, 2% Duty CycleOperating Current 90 to 160 mA N/ADetector Voltage 0.3 (Volts) into 2 K-ohm Load 0.3 (Volts) into 2 K-ohm Load
∆F/∆T -0.50 MHz/°C (maximum) -0.50 MHz/°C (maximum)∆P/∆T -0.04 dB/°C (maximum) -0.04 dB/°C (maximum)
Operation temperature -40 to +85 °C -40 to +85 °CStorage temperature -50 to + 90 °C -50 to + 90 °C
8-81High quality microwave and millimeterwave components and subsystems. Visit Ducommun Technologies online at www.ducommun.com.
8
Doppler Sensor Heads
FEATURES
High sensitivityLow 1/f noise Circular polarized waveformLow harmonic and spurious emission Temperature and vibration qualifiedCompact sizeLow cost and volume production
Automotive RadarDoppler RadarDirectional sensorLong range motion detector
APPLICATIONS
SRF series Single and Dual Channel Doppler Sensor Heads are designed for long range motion/speed/directional detection where the sensitivity is essential. The sensors are constructed with a high performance horn antenna or horn-lens antenna, a linear to circular polarizer and T/R diplexer, a balanced mixer (I/Q mixer for dual channel version) and a high performance Gunn diode oscillator or dielectric resonator oscillator/multiplier chain. The low 1/f noise mixer diodes and high performance oscillator enhance Doppler detection at low IF frequency and circular polarization waveform improves reception ability for various Radar targets. The sensors are offered with single or dual channel version. The dual channel version provides target moving direction (approaching or receding) information of the target while detecting speed.
Standard products are offered at 24.15 GHz, 35 GHz and 76.5 GHz, while other frequency bands are available upon request.
DESCRIPTION
SPECIFICATIONS
Bulletin No. SRF
SRF Series
Typical Specifications (Single Channel)
Parameters / Model # SRF-24120610-01 SRF-35120610-01 SRF-77120910-01RF frequency 24.150 GHz 35.500 GHz 76.500 GHz
Transmitter output power +10 dBm (typical) +10 dBm (typical) +10 dBm (typical)Receiver conversion loss 6 dB (typical) 6 dB (typical) 9 dB (typical)
IF bandwidth DC to 100 MHz (minimum) DC to 100 MHz (minimum) DC to 100 MHz (minimum)Antenna 3 dB beamwidth 12 degrees (typical) 12 degrees (typical) 12 degrees (typical)
Antenna side lob level -20 dB (maximum) -20 dB (maximum) -20 dB (maximum)Polarization right hand circular right hand circular right hand circular
Spurious and harmonics -16 dBc (maximum) -16 dBc (maximum) -16 dBc (maximum) ∆F/∆T -0.20 MHz/°C (maximum) -0.40 MHz/°C (maximum) -4.0 MHz/°C (typical) ∆P/∆T -0.03 dB/°C (maximum) -0.04 dB/°C (maximum) -0.04 dB/°C (typical)DC bias +5.5 V / 250 mA (typical) +5.5 V / 350 mA (typical) +5.5 V / 650 mA (typical)
Operation temperature -40 to +85 °C -40 to +85 °C -40 to +85 °COutline drawing WT-C-A1 WT-C-A2 Consult factory
High quality microwave and millimeterwave components and subsystems. Visit Ducommun at www.ducommun.com
8-818-95High quality microwave and millimeterwave components and subsystems. Visit Ducommun Technologies online at www.ducommun.com.
8
Sub-assemblies
Bulletin No. SSS
FEATURES
Custom designedIntegrated module or bolt together solution High performanceQuick deliveryCost effective
RadarSensorsModulesTest set
APPLICATIONS
Among them, the K and Ka band directional Doppler Radar front ends are in production. More than one thousand sets have been delivered. In addition, Ducommun Technologies has delivered Ka through W band engineering prototypes for plasma detection system, automotive Radar, speed Radar, automatic test set, Radio Telescope, Missile terminal guidance, telecommunication system, etc. applications.
Ducommun Technologies is approved to be a company who can not only supply high performance catalog products, but also realize a concept into the hardware with state-of-the-art performance prototypes and cost effective volume production.
DESCRIPTION
35 GHz 10 W PA Assembly
30 GHz Plasma Detection Sensor Assembly
Ducommun Technologies understands customers’ needs. Ducommun Technologies not only supplies the standard and custom made components and modules, but also understands the importance of providing engineering design and service to its customers.
Ducommun Technologies’s self-contained, in-house components design and fabrication capacities ensured the breath of sub-assemblies offer from rapid prototyping and proof of concept to full production. Ducommun Technologies has produced many high performance millimeterwave band sub-assemblies for specific commercial and military system applications.
K and Ka Band Doppler Sensor Assemblies
76155_DucMMWaveCat.indd 81 3/17/14 2:18 PM
8-82High quality microwave and millimeterwave components and subsystems. Visit Ducommun Technologies online at www.ducommun.com.
NO PINS IN THIS SIDEFOR SINGLE CHANNEL
GN
D
IF-I
GN
D
IF-Q
WiseW
ave
M/N
: XX
XX
XS
/N: X
XX
XX
D/C
: XX
/XX
4-40 x 0.20 DP4 PLS (2 PLS ON THE OTHER SIDE)
GN
D
IF-I
WiseW
ave
NO PINS ON THIS SIDEFOR SINGLE CHANNEL
4-40 x 0.20 DP4 PLS
(2 PLS ON THE OTHER SIDE)
Doppler Sensor Heads
Bulletin No. SRF
Typical Specifications (Dual Channel)Parameters / Model # SRF-24120910-D1 SRF-35121010-D1 SRF-77121210-D1RF frequency 24.150 GHz 35.500 GHz 76.500 GHzTransmitter output power +10 dBm (typical) +10 dBm (typical) +10 dBm (typical)Receiver conversion loss 9 dB (typical) 10 dB (typical) 12 dB (typical)IF bandwidth DC to 100 MHz (minimum) DC to 100 MHz (minimum) DC to 100 MHz (minimum)I/Q Channel Phase 90 °± 10 ° 90 °± 10 ° 90 °± 20 °Antenna 3 dB beamwidth 12 degrees (typical) 12 degrees (typical) 12 degrees (typical)Antenna side lob level -20 dB (maximum) -20 dB (maximum) -20 dB (typical)Polarization right hand circular right hand circular right hand circularSpurious and harmonics -16 dBc (maximum) -16 dBc (maximum) -16 dBc (maximum)∆F/∆T -0.20 MHz/°C (maximum) -0.40 MHz/°C (maximum) -4.0 MHz/°C (typical)∆P/∆T -0.03 dB/°C (maximum) -0.04 dB/°C (maximum) -0.04 dB/°C (typical)DC bias +5.5 V / 250 mA (typical) +5.5 V / 350 mA (typical) +5.5 V / 650 mA (typical)Operation temperature -40 to +85 °C -40 to +85 °C -40 to +85 °COutline drawing WT-C-A1 WT-C-A2 Consult factory
OUTLINES
K Band Doppler Sensor Heads Ka Band Doppler Sensor Heads
Oscillator Outline may alter
WT-C-A1 WT-C-A2
8-83High quality microwave and millimeterwave components and subsystems. Visit Ducommun Technologies online at www.ducommun.com.
8
Ranging Sensor Heads
FEATURES
High sensitivityLow 1/f noise Circular polarized waveformLow harmonic and spurious emission Temperature and vibration qualifiedCompact sizeLow cost and volume production
Automotive RadarRanging Radar
APPLICATIONS
SRR series ranging sensor heads are designed for long range distance detection where the sensitivity is essential. The sensors are constructed with a high performance horn antenna or horn-lens antenna, a linear to circular polarizer and T/R diplexer, a balanced mixer and a high performance varactor tuned Gunn oscillator or dielectric resonator VCO/multiplier chain. The low 1/f noise mixer diodes and high performance oscillator enhance the detection sensitivity at low IF frequency and circular polarization waveform improves reception ability for various Radar targets. The standard models are offered with single channel output and the dual channel version are available per request.
Standard products are offered at 24.15 GHz, 35.0 GHz and 76.5 GHz, while other frequency bands are available upon request.
DESCRIPTION
SPECIFICATIONS
Bulletin No. SRR
SRR Series
Parameters / Model # SRR-24120610-01 SRR-35120610-01 SRR-77120910-01
RF frequency 24.150 GHz 35.500 GHz 76.500 GHzVaractor Tuning Range 50 MHz (Min) / 0 to +20 V (Typ.) 100 MHz (Min) / 0 to +20 V (Typ.) 250 MHz (Min) / 0 to +20 V (Typ.)Transmitter output power +10 dBm (typical) +10 dBm (typical) +10 dBm (typical)Receiver conversion loss 6 dB (typical) 6 dB (typical) 9 dB (typical)IF bandwidth DC to 100 MHz (minimum) DC to 100 MHz (minimum) DC to 100 MHz (minimum)Antenna 3 dB beamwidth 12 degrees (typical) 12 degrees (typical) 12 degrees (typical)Antenna side lob level -20 dB (maximum) -20 dB (maximum) -20 dB (maximum)Polarization right hand circular right hand circular right hand circularSpurious and harmonics -16 dBc (maximum) -16 dBc (maximum) -16 dBc (maximum)∆F/∆T -0.20 MHz/°C (maximum) -0.40 MHz/°C (maximum) -4.0 MHz/°C (typical)∆P/∆T -0.03 dB/°C (maximum) -0.04 dB/°C (maximum) -0.04 dB/°C (typical)DC bias +5.5 V / 250 mA (typical) +5.5 V / 350 mA (typical) +5.5 V / 650 mA (typical)Operation temperature -40 to +85 °C -40 to +85 °C -40 to +85 °COutline drawing WT-C-A3 WT-C-A4 Consult factory
High quality microwave and millimeterwave components and subsystems. Visit Ducommun at www.ducommun.com
8-82
76155_DucMMWaveCat.indd 82 3/17/14 2:18 PM
8-84High quality microwave and millimeterwave components and subsystems. Visit Ducommun Technologies online at www.ducommun.com.
4-40 x 0.20 DP4 PLS (2 PLS ON THE OTHER SIDE)
NO PINS ON THIS SIDEFOR SINGLE CHANNEL
M/N
: XX
XXX
S/N
: XX
XXX
D/C
: XX/
XX
WiseW
ave
GN
D
IF-Q
GN
D
IF-I
4-40 x 0.20 DP4 PLS (2 PLS ON THE OTHER SIDE)
M/N
: XXX
XXS
/N: X
XXXX
D/C
: XX/
XX
WiseW
ave
GN
D
IF-Q
GN
D
IF-I
NO PINS ON THISSIDE FOR SINGLECHANNEL
Ranging Sensor Heads
Bulletin No. SRR
OUTLINES
Typical Specifications (Dual Channel)
Parameters / Model # SRR-24120910-D1 SRR-35121010-D1 SRR-77121210-D1 RF frequency 24.150 GHz 35.500 GHz 76.500 GHz Varactor tuning range 50 MHz (Min) 0 to +20 V (Typ.) 100 MHz (Min) 0 to +20 V (Typ.) 250 MHz (Min) 0 to +20 V (Typ.) Transmitter output power +10 dBm (typical) +10 dBm (typical) +10 dBm (typical) Receiver conversion loss 9 dB (typical) 9 dB (typical) 12 dB (typical) IF bandwidth DC to 100 MHz (minimum) DC to 100 MHz (minimum) DC to 100 MHz (minimum) Antenna 3 dB beamwidth 12 degrees (typical) 12 degrees (typical) 12 degrees (typical) Antenna side lob level -20 dB (maximum) -20 dB (maximum) -20 dB (maximum) Polarization right hand circular right hand circular right hand circular Spurious and harmonics -16 dBc (maximum) -16 dBc (maximum) -16 dBc (maximum) ∆F/∆T -0.20 MHz/°C (maximum) -0.40 MHz/°C (maximum) -4.0 MHz/°C (typical) ∆P/∆T -0.03 dB/°C (maximum) -0.04 dB/°C (maximum) -0.04 dB/°C (typical) DC bias +5.5 V / 250 mA (typical) +5.5 V / 350 mA (typical) +5.5 V / 650 mA (typical) Operation temperature -40 to +85 °C -40 to +85 °C -40 to +85 °C Outline drawing WT-C-A3 WT-C-A4 Consult factory
K Band Ranging Sensor Heads Ka Band Ranging Sensor Heads
Oscillator Outline may alter
WT-C-A3 WT-C-A4
8-85High quality microwave and millimeterwave components and subsystems. Visit Ducommun Technologies online at www.ducommun.com.
8
Sensor Heads Application Notes
Bulletin No. SRF & SRR
Ducommun Technologies offers three types of microwave and millimeterwave sensor heads. They are Doppler Sensor Heads, Directional Doppler Sensor Heads (SRF Series) and Ranging Sensor Heads (SRR Series). The main objectives of the application notes are to explain the basic principles of Doppler Radar and Ranging (Distance) Radar and how Ducommun Technologies’ sensor heads should be implemented to configure such Radar systems.
SRF series single channel Doppler sensor heads offered by Ducommun Technologies are designed for long range Doppler Radar application where detection sensitivity is essential.
The simplified block diagram of a Doppler Radar formed by using Ducommun Technologies’s single channel sensor head is shown in Fig. 2. A high quality DC power supply for Gunn oscillator bias, a low noise IF amplifier and DSP circuitry are the minimum requirements for a system designer to realize such a radar system. In addition, the moving target radar cross section, detection distance and target speed are the main factors in consideration when specifying the transmitting power, antenna gain and IF frequency bandwidth of the sensor head. The example of the IF frequency range of a 24.15 GHz and 76.5 GHz Doppler radar at various speeds is shown in the following table.
Doppler Radar
When moving target moves perpendicular to the radar beam, the Fd equals 0, which indicates no Doppler shift. On the other hand, the Fd is equal to 2V(Fo/C) when the target moves parallel to the radar beam or if q is real small (0 to 10 degrees).
It is well known that Doppler Radar is widely used for speed measurement. The principle behind the Doppler Radar is the frequency shift of a microwave signal bounced back by a moving object. The resultant frequency shift is known as Doppler Frequency Shift, which is given by the following equation
Fd = 2V (Fo/C) Cos (θ)
Where:
Fo is the transmitter frequency (Hertz).C is the speed of light, which is 3 x 108 (meter/sec).V is the speed of the target (meter/sec). θ is the angle between the radar beam and the moving target (in degrees) as shown in Fig. 1.
Radar
Targetθ
Figure 1. Doppler Shift
Transmitting Freq. (GHz) 24.15
Speed (Km/Hr.) 10 80 200
IF (Hz) 224 1,790 4,475
Transmitting Freq. (GHz) 76.50
Speed (Km/Hr.) 10 80 200
IF (Hz) 709 5,670 14,176
Figure 2. Simplied Doppler Radar
High quality microwave and millimeterwave components and subsystems. Visit Ducommun at www.ducommun.com
8-858-95High quality microwave and millimeterwave components and subsystems. Visit Ducommun Technologies online at www.ducommun.com.
8
Sub-assemblies
Bulletin No. SSS
FEATURES
Custom designedIntegrated module or bolt together solution High performanceQuick deliveryCost effective
RadarSensorsModulesTest set
APPLICATIONS
Among them, the K and Ka band directional Doppler Radar front ends are in production. More than one thousand sets have been delivered. In addition, Ducommun Technologies has delivered Ka through W band engineering prototypes for plasma detection system, automotive Radar, speed Radar, automatic test set, Radio Telescope, Missile terminal guidance, telecommunication system, etc. applications.
Ducommun Technologies is approved to be a company who can not only supply high performance catalog products, but also realize a concept into the hardware with state-of-the-art performance prototypes and cost effective volume production.
DESCRIPTION
35 GHz 10 W PA Assembly
30 GHz Plasma Detection Sensor Assembly
Ducommun Technologies understands customers’ needs. Ducommun Technologies not only supplies the standard and custom made components and modules, but also understands the importance of providing engineering design and service to its customers.
Ducommun Technologies’s self-contained, in-house components design and fabrication capacities ensured the breath of sub-assemblies offer from rapid prototyping and proof of concept to full production. Ducommun Technologies has produced many high performance millimeterwave band sub-assemblies for specific commercial and military system applications.
K and Ka Band Doppler Sensor Assemblies
Ducommun offers three types of microwave and millimeterwave sensor heads. They are Doppler Sensor Heads, Directional Doppler Sensor Heads (SRF Series) and Ranging Sensor Heads (SRR Series). The main objectives of the application notes are to explain the basic principles of Doppler Radar and Ranging (Distance) Radar and how Ducommun’s sensor heads should be implemented to configure such Radar systems.
SRF series single channel Doppler sensor heads offered by Ducommun are designed for long range Doppler Radar application where detection sensitivity is essential.
The simplified block diagram of a Doppler Radar formed by using Ducommun’s single channel sensor head is shown in Fig. 2. A high quality DC power supply for Gunn oscillator bias, a low noise IF amplifier and DSP circuitry are the minimum requirements for a system designer to realize such a radar system. In addition, the moving target radar cross section, detection distance and target speed are the main factors in consideration when specifying the transmitting power, antenna gain and IF frequency bandwidth of the sensor head. The example of the IF frequency range of a 24.15 GHz and 76.5 GHz Doppler radar at various speeds is shown in the following table.
76155_DucMMWaveCat.indd 85 3/17/14 2:18 PM
8-86High quality microwave and millimeterwave components and subsystems. Visit Ducommun Technologies online at www.ducommun.com.
Bulletin No. SRF & SRR
In certain applications, one not only has to know the target speed, but also the target moving directions, i.e., whether the target is approaching to the radar or receding from the Radar. The examples for such applications are the law enforcement radar systems used by police officer or door openers in the building entrance. Also, such radar systems are often used for distinguishing vibrating targets, fan rotations or curtain movements caused by the wind from a real intrusion in the security system.
The implement of the directional information is realized by adding an additional mixer to the single channel sensor head with a 90 degrees phase difference. The mixer used in the directional sensor is sometimes known as phase detector or I/Q mixer. The phase relationship between two mixers is that the first mixer will lead the second, or the phase shift is positive if the target is approaching the radar, while the phase will lag if the target is receding from the radar.
SRF series dual channel Doppler sensor heads offered by Ducommun Technologies are designed for long range Directional Doppler Radar applications where detection sensitivity is essential.
The simplified block diagram of a Directional Doppler Radar achieved by using Ducommun Technologies’s dual channel sensor head is shown in the Fig. 3. In a similar manner, a high quality DC power supply for Gunn oscillator bias, a low noise IF amplifier and DSP circuitry are the minimum requirements for a system designer to realize such a radar system.
In many applications, one has to know not only the speed of a moving target, but also the range or distance between the moving or stationary target and the radar. In this case, a Frequency Modulation Continuos Waveform (FMCW) technique may be used in the sensor head to realize the ranging radar.
Implementing the FMCW technique in the sensor head is to replace the fixed tuned oscillator with a Varactor or voltage tuned one.
Figure 4. Simplied FMCW Ranging Radar
Doppler Directional Radar
Ranging (Distance) Radar
DCPower
PolarizerDiplexer
GunnOsc.
PhaseDetectorDSPDisplay
Control Unit
Mixer 1
IF1
SRF Dual
Mixer 2
IF2
90 °
Amp 1 Amp 2
Figure 3. Simplied Directional Doppler Radar
SRR series dual channel Doppler sensor heads offered by Ducommun Technologies are designed for long range FMCW Radar application.
DCPower
PolarizerDiplexer
GunnOsc.
IFAmplifie
r
DSPDisplay
Control Unit
Mixer
IFSRR Single
8-87High quality microwave and millimeterwave components and subsystems. Visit Ducommun Technologies online at www.ducommun.com.
8
Bulletin No. SRF & SRR
The simplified block diagram of an FMCW Radar formed by using Ducommun Technologies’ single channel sensor head is shown in the Fig. 4. In a similar manner, a high quality DC power supply for Gunn oscillator bias, a voltage modulator, a low noise IF amplifier and DSP circuitry are the minimum requirements for a system designer to realize such a radar system. The range information can be extracted from the frequency difference between the transmitted and returned signal at distance R, the signal transit time (∆T) and the frequency modulation rate (N). The idea is briefly illustrated in the Fig. 5. The detail is explained as follow. At time T1, the signal is transmitted and fed to the mixer at frequency F1. The F1 returned from the target at distance R is received at T2, while the transmitting and LO frequency is F2. With known ramping rate (N), one can find the transit time by using
∆T = (Ft-Fr)/N,
where Ft and Fr are the IF frequency at mixer IF port in Hz and N is Hz/sec.
From the description above, an FMCW ranging radar can detect not only the stationary target, but also the moving target. Therefore, an FMCW radar is a Doppler Ranging Radar.
Therefore, the range (distance) is given by
R = (∆T x C)/2
Where C is the speed of light, which is 3 x 108 (meter/sec).
The range accuracy is governed by the ramp linearity.
Figure 5. FMCW Radar Frequency vs. Time
F (GHz)
∆F
∆T
TransmitterFrequency Returned
Frequency at Range R
TimeT1 T2
F1
F2
Ranging (Distance) Radar with Directional Doppler Feature
With a similar idea, Ducommun Technologies’ SRR series Dual channel sensor head offers ranging capacity with directional features. The simplified block diagram is shown in Fig. 6.
Figure 6. Simplied FMCW Ranging Radar with Directional Doppler Feature
Conclusions
1. Ducommun Technologies’ SRF and SRR series sensor heads offer total solutions for Long Range Radar system requirements.
2. Ducommun Technologies’ SRF and SRR series sensor heads can be tailored to various transmitting power levels and antenna gains.
DCPower
VoltageModulator
PolarizerDiplexer
GunnOsc.
PhaseDetectorDSPDisplay
Control Unit
Mixer 1
IF1
SRF Dual
Mixer 2
IF2
90 °
Amp 1 Amp 2
High quality microwave and millimeterwave components and subsystems. Visit Ducommun at www.ducommun.com
8-86
In certain applications, one not only has to know the target speed, but also the target moving directions, i.e., whether the target is approaching to the radar or receding from the Radar. The examples for such applications are the law enforcement radar systems used by police officer or door openers in the building entrance. Also, such radar systems are often used for distinguishing vibrating targets, fan rotations or curtain movements caused by the wind from a real intrusion in the security system.
The implement of the directional information is realized by adding an additional mixer to the single channel sensor head with a 90 degrees phase difference. The mixer used in the directional sensor is sometimes known as phase detector or I/Q mixer. The phase relationship between two mixers is that the first mixer will lead the second, or the phase shift is positive if the target is approaching the radar, while the phase will lag if the target is receding from the radar.
SRF series dual channel Doppler sensor heads offered by Ducommun are designed for long range Directional Doppler Radar applications where detection sensitivity is essential.
The simplified block diagram of a Directional Doppler Radar achieved by using Ducommun’s dual channel sensor head is shown in the Fig. 3. In a similar manner, a high quality DC power supply for Gunn oscillator bias, a low noise IF amplifier and DSP circuitry are the minimum requirements for a system designer to realize such a radar system.
SRR series dual channel Doppler sensor heads offered by Ducommun are designed for long range FMCW Radar application.
76155_DucMMWaveCat.indd 86 3/17/14 2:18 PM
8-86High quality microwave and millimeterwave components and subsystems. Visit Ducommun Technologies online at www.ducommun.com.
Bulletin No. SRF & SRR
In certain applications, one not only has to know the target speed, but also the target moving directions, i.e., whether the target is approaching to the radar or receding from the Radar. The examples for such applications are the law enforcement radar systems used by police officer or door openers in the building entrance. Also, such radar systems are often used for distinguishing vibrating targets, fan rotations or curtain movements caused by the wind from a real intrusion in the security system.
The implement of the directional information is realized by adding an additional mixer to the single channel sensor head with a 90 degrees phase difference. The mixer used in the directional sensor is sometimes known as phase detector or I/Q mixer. The phase relationship between two mixers is that the first mixer will lead the second, or the phase shift is positive if the target is approaching the radar, while the phase will lag if the target is receding from the radar.
SRF series dual channel Doppler sensor heads offered by Ducommun Technologies are designed for long range Directional Doppler Radar applications where detection sensitivity is essential.
The simplified block diagram of a Directional Doppler Radar achieved by using Ducommun Technologies’s dual channel sensor head is shown in the Fig. 3. In a similar manner, a high quality DC power supply for Gunn oscillator bias, a low noise IF amplifier and DSP circuitry are the minimum requirements for a system designer to realize such a radar system.
In many applications, one has to know not only the speed of a moving target, but also the range or distance between the moving or stationary target and the radar. In this case, a Frequency Modulation Continuos Waveform (FMCW) technique may be used in the sensor head to realize the ranging radar.
Implementing the FMCW technique in the sensor head is to replace the fixed tuned oscillator with a Varactor or voltage tuned one.
Figure 4. Simplied FMCW Ranging Radar
Doppler Directional Radar
Ranging (Distance) Radar
DCPower
PolarizerDiplexer
GunnOsc.
PhaseDetectorDSPDisplay
Control Unit
Mixer 1
IF1
SRF Dual
Mixer 2
IF2
90 °
Amp 1 Amp 2
Figure 3. Simplied Directional Doppler Radar
SRR series dual channel Doppler sensor heads offered by Ducommun Technologies are designed for long range FMCW Radar application.
DCPower
PolarizerDiplexer
GunnOsc.
IFAmplifie
r
DSPDisplay
Control Unit
Mixer
IFSRR Single
8-87High quality microwave and millimeterwave components and subsystems. Visit Ducommun Technologies online at www.ducommun.com.
8
Bulletin No. SRF & SRR
The simplified block diagram of an FMCW Radar formed by using Ducommun Technologies’ single channel sensor head is shown in the Fig. 4. In a similar manner, a high quality DC power supply for Gunn oscillator bias, a voltage modulator, a low noise IF amplifier and DSP circuitry are the minimum requirements for a system designer to realize such a radar system. The range information can be extracted from the frequency difference between the transmitted and returned signal at distance R, the signal transit time (∆T) and the frequency modulation rate (N). The idea is briefly illustrated in the Fig. 5. The detail is explained as follow. At time T1, the signal is transmitted and fed to the mixer at frequency F1. The F1 returned from the target at distance R is received at T2, while the transmitting and LO frequency is F2. With known ramping rate (N), one can find the transit time by using
∆T = (Ft-Fr)/N,
where Ft and Fr are the IF frequency at mixer IF port in Hz and N is Hz/sec.
From the description above, an FMCW ranging radar can detect not only the stationary target, but also the moving target. Therefore, an FMCW radar is a Doppler Ranging Radar.
Therefore, the range (distance) is given by
R = (∆T x C)/2
Where C is the speed of light, which is 3 x 108 (meter/sec).
The range accuracy is governed by the ramp linearity.
Figure 5. FMCW Radar Frequency vs. Time
F (GHz)
∆F
∆T
TransmitterFrequency Returned
Frequency at Range R
TimeT1 T2
F1
F2
Ranging (Distance) Radar with Directional Doppler Feature
With a similar idea, Ducommun Technologies’ SRR series Dual channel sensor head offers ranging capacity with directional features. The simplified block diagram is shown in Fig. 6.
Figure 6. Simplied FMCW Ranging Radar with Directional Doppler Feature
Conclusions
1. Ducommun Technologies’ SRF and SRR series sensor heads offer total solutions for Long Range Radar system requirements.
2. Ducommun Technologies’ SRF and SRR series sensor heads can be tailored to various transmitting power levels and antenna gains.
DCPower
VoltageModulator
PolarizerDiplexer
GunnOsc.
PhaseDetectorDSPDisplay
Control Unit
Mixer 1
IF1
SRF Dual
Mixer 2
IF2
90 °
Amp 1 Amp 2
High quality microwave and millimeterwave components and subsystems. Visit Ducommun at www.ducommun.com
8-878-95High quality microwave and millimeterwave components and subsystems. Visit Ducommun Technologies online at www.ducommun.com.
8
Sub-assemblies
Bulletin No. SSS
FEATURES
Custom designedIntegrated module or bolt together solution High performanceQuick deliveryCost effective
RadarSensorsModulesTest set
APPLICATIONS
Among them, the K and Ka band directional Doppler Radar front ends are in production. More than one thousand sets have been delivered. In addition, Ducommun Technologies has delivered Ka through W band engineering prototypes for plasma detection system, automotive Radar, speed Radar, automatic test set, Radio Telescope, Missile terminal guidance, telecommunication system, etc. applications.
Ducommun Technologies is approved to be a company who can not only supply high performance catalog products, but also realize a concept into the hardware with state-of-the-art performance prototypes and cost effective volume production.
DESCRIPTION
35 GHz 10 W PA Assembly
30 GHz Plasma Detection Sensor Assembly
Ducommun Technologies understands customers’ needs. Ducommun Technologies not only supplies the standard and custom made components and modules, but also understands the importance of providing engineering design and service to its customers.
Ducommun Technologies’s self-contained, in-house components design and fabrication capacities ensured the breath of sub-assemblies offer from rapid prototyping and proof of concept to full production. Ducommun Technologies has produced many high performance millimeterwave band sub-assemblies for specific commercial and military system applications.
K and Ka Band Doppler Sensor Assemblies
The simplified block diagram of an FMCW Radar formed by using Ducommun’s single channel sensor head is shown in the Fig. 4. In a similar manner, a high quality DC power supply for Gunn oscillator bias, a voltage modulator, a low noise IF amplifier and DSP circuitry are the minimum requirements for a system designer to realize such a radar system. The range information can be extracted from the frequency difference between the transmitted and returned signal at distance R, the signal transit time (∆T) and the frequency modulation rate (N). The idea is briefly illustrated in the Fig. 5. The detail is explained as follow. At time T1, the signal is transmitted and fed to the mixer at frequency F1. The F1 returned from the target at distance R is received at T2, while the transmitting and LO frequency is F2. With known ramping rate (N), one can find the transit time by using
∆T = (Ft-Fr)/N,
where Ft and Fr are the IF frequency at mixer IF port in Hz and N is Hz/sec.
With a similar idea, Ducommun’s SRR series Dual channel sensor head offers ranging capacity with directional features. The simplified block diagram is shown in Fig. 6.
1. Ducommun’s SRF and SRR series sensor heads offer total solutions for Long Range Radar system requirements.
2. Ducommun’s SRF and SRR series sensor heads can be tailored to various transmitting power levels and antenna gains.
76155_DucMMWaveCat.indd 87 3/17/14 2:18 PM