Motherboard Mamual k8vm800m-Rh e

GA-K8VM800M /GA-K8VM800M-RHAMD Socket 754 Processor Motherboard

User's ManualRev. 200412ME-K8VM800M-2004R

* The WEEE marking on the product indicates this product must not be disposed of with user's other household wasteand must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!

* The WEEE marking applies only in European Union's member states.

Aug. 8, 2005

MotherboardGA-K8VM

800M

Motherboard

GA

-K8V

M800M

Aug. 8, 2005

Jun. 21, 2006

MotherboardGA-K8VM

800M-RH

Motherboard

GA

-K8V

M800M

-RH

Jun. 21, 2006

Copyright© 2006 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.The trademarks mentioned in the manual are legally registered to their respective companies.

NoticeThe written content provided with this product is the property of Gigabyte.No part of this manual may be reproduced, copied, translated, or transmitted in any form or by anymeans without Gigabyte's prior written permission. Specifications and features are subject tochange without prior notice.

Product Manual ClassificationIn order to assist in the use of this product, Gigabyte has categorized the user manual in thefollowing:

For detailed product information and specifications, please carefully read the "Product User Manual".

For detailed information related to Gigabyte's unique features, please go to "TechnologyGuide" section on Gigabyte's website to read or download the information you need.

For more product details, please click onto Gigabyte's website at www.gigabyte.com.tw

- 5 -

Table of Contents

GA-K8VM800M(-RH) Motherboard Layout .................................................................... 7Block Diagram ................................................................................................................ 8

Chapter 1 Hardware Installation .................................................................................... 91-1 Considerations Prior to Installation .................................................................... 91-2 Feature Summary .......................................................................................... 101-3 Installation of the CPU and Heatsink .............................................................. 12

1-3-1 Installation of the CPU ......................................................................................... 121-3-2 Installation of the Heatsink .................................................................................. 13

1-4 Installation of Memory .................................................................................... 141-5 Installation of Expansion Cards ...................................................................... 151-6 I/O Back Panel Introduction ........................................................................... 161-7 Connectors Introduction .................................................................................. 17

Chapter 2 BIOS Setup ................................................................................................ 27The Main Menu (For example: BIOS Ver. : D1) ....................................................... 282-1 Standard CMOS Features ............................................................................. 302-2 Advanced BIOS Features .............................................................................. 322-3 Integrated Peripherals ..................................................................................... 332-4 Power Management Setup ............................................................................. 362-5 PnP/PCI Configurations ................................................................................. 382-6 PC Health Status ........................................................................................... 392-7 Frequency / Voltage Control ........................................................................... 402-8 Load Fail-Safe Defaults ................................................................................... 412-9 Load Optimized Defaults ................................................................................. 412-10 Set Supervisor/User Password ..................................................................... 422-11 Save & Exit Setup ......................................................................................... 432-12 Exit Without Saving ....................................................................................... 43

- 6 -

Chapter 3 Drivers Installation ...................................................................................... 453-1 Install Chipset Drivers .................................................................................... 453-2 Software Application ....................................................................................... 463-3 Software Information ....................................................................................... 463-4 Hardware Information ..................................................................................... 473-5 Contact Us ..................................................................................................... 47

Chapter 4 Appendix ................................................................................................... 494-1 Unique Software Utilities ................................................................................ 49

4-1-1 EasyTune 5 Introduction ..................................................................................... 504-1-2 Xpress Recovery Introduction ........................................................................... 514-1-3 Flash BIOS Method Introduction ........................................................................ 544-1-4 Serial ATA BIOS Setting Utility Introduction ...................................................... 634-1-5 2 / 4 / 6 Channel Audio Function Introduction ................................................. 70

4-2 Troubleshooting ............................................................................................... 74

- 7 -

GA-K8VM800M(-RH) Motherboard Layout

ATX

MS/KB

LPT

COMA ATX_12V

Socket 754R_USB

DDR2

DDR1

COMB

CODEC

IT8705

VIA VT8237R /VT8237R+

BIOS PCI1

PCI2

F_USB2F_USB1

CLR_CMOS

SATA1SYS_FAN

GA-K

8VM8

00M(

-RH)

F_PANEL

PCI3 BAT

F_AUDIO

CD_IN

VIA 6103L

AGP

PWR_LED

FDD

IDE2 IDE1

CPU_FAN

AUDIO

USB

LAN

VGA

SATA0IR

SPDIF_IO

VIA K8M800

- 8 -

Block Diagram

CPUCLK+/- (200MHz)

H.T. Bus 800MHz

33 MHz14.318 MHz

AGP4X/8X

AGPCLK(66MHz)

3 PCI

PCICLK(33MHz)

RJ45

AC97

Lin

k

MIC

LINE

-INLI

NE-O

UT

2 Serial ATA

400/333/266/200MHzDDR RAM

LPC BUS

8 USBPorts

24MHz33 MHz

Floppy

PS/2 KB/Mouse

2 COMPorts

BIOS

ATA33/66/100/133IDE Channels

LAN

AMDAlthlonTM 64

processor (K8)

VGA Port

AudioCODEC

IR

IT8705LPT Port

VIA 6103L

VIA VT8237R /VT8237R+

Mll-Link

66 MHz

VIA K8M80066 MHz14.318 MHz

Hardware Installation- 9 -

English1-1 Considerations Prior to InstallationPreparing Your ComputerThe motherboard contains numerous delicate electronic circuits and components which canbecome damaged as a result of electrostatic discharge (ESD). Thus, prior to installation, pleasefollow the instructions below:1. Please turn off the computer and unplug its power cord.2. When handling the motherboard, avoid touching any metal leads or connectors.3. It is best to wear an electrostatic discharge (ESD) cuff when handling electronic components

(CPU, RAM).4. Prior to installing the electronic components, please have these items on top of an antistatic

pad or within a electrostatic shielding container.5. Please verify that the power supply is switched off before unplugging the power supply

connector from the motherboard.

Installation Notices1. Prior to installation, please do not remove the stickers on the motherboard. These stickers

are required for warranty validation.2. Prior to the installation of the motherboard or any hardware, please first carefully read the

information in the provided manual.3. Before using the product, please verify that all cables and power connectors are connected.4. To prevent damage to the motherboard, please do not allow screws to come in contact with

the motherboard circuit or its components.5. Please make sure there are no leftover screws or metal components placed on the motherboard

or within the computer casing.6. Please do not place the computer system on an uneven surface.7. Turning on the computer power during the installation process can lead to damage to system

components as well as physical harm to the user.8. If you are uncertain about any installation steps or have a problem related to the use of the

product, please consult a certified computer technician.

Instances of Non-Warranty1. Damage due to natural disaster, accident or human cause.2. Damage as a result of violating the conditions recommended in the user manual.3. Damage due to improper installation.4. Damage due to use of uncertified components.5. Damage due to use exceeding the permitted parameters.6. Product determined to be an unofficial Gigabyte product.

Chapter 1Hardware Installation

GA-K8VM800M(-RH) Motherboard - 10 -

Engl

ish

CPU Socket 754 for AMD AthlonTM 64 processor (K8)1600MH/z system busSupports core frequencies in excess of 3000+ and faster

Chipset Northbridge: VIA K8M800Southbridge: VIA VT8237R / VT8237R+

Memory 2 DDR DIMM memory slots (supports up to 2GB memory)Supports DDR 400(Note 1)/333/266/200 DIMMSupports 2.5V DDR DIMM

Slots 1 AGP slot3 PCI slots

IDE Connections 2 IDE connection (UDMA 33/ATA 66/ATA 100/ATA 133), allows connection of4 IDE devices

FDD Connections 1 FDD connection, allows connection of 2 FDD devicesOnboard SATA 2 Serial ATA connections (Note2)

Peripherals 1 parallel port supporting Normal/EPP/ECP mode1 serial port (COMA), 1 VGA port, onboard COMB connection8 USB 2.0/1.1 ports (rear x 4, front x 4 via cable)1 front audio connector1 IR connector1 PS/2 keyboard port1 PS/2 mouse port

On-Board VGA Build in VIA K8M800 ChipsetOnboard LAN Onboard VIA 6103L chip (10/100 Mbit)

1 RJ 45 portOnboard Audio Realtek ALC655 CODEC

Supports Line In ; Line Out ; MIC InSupports 2 / 4 / 6 channel audioSPDIF In/Out connectionCD In connection

I/O Control IT8705

1-2 Feature Summary

(Note 1) Because of CPU limitations, if you want to install DDR400 memory modules in your system, please install eitherone double-sided or two single-sided DDR400 memory modules. The DDR400 speed will drop down to DDR333 ifyou install two double-sided DDR400 memory modules.

(Note 2) It is recommended to use SATA (1.5Gb/s) hard disks.


English

On-Board SATA RAID Built in VIA VT8237R / VT8237R+Supports Disk striping (RAID0) or DISK Mirroring (RAID1)Supports UDMA up to 150 MB/secUp to 2 SATA Device

Hardware Monitor System voltage detectionCPU temperature detectionCPU / System fan speed detectionCPU fan failure warning

BIOS Use of licensed AWARD BIOSSupports Q-Flash

Additional Features Supports @BIOSSupports EasyTune (Note 3)

Overclocking Over Clock (CPU) by BIOSOver Voltage (CPU/AGP) by BIOS

Form Factor Micro ATX form factor; 22.0cm x 24.4cm

(Note 3) EasyTune functions may vary depending on different motherboards.


Engl

ish

1-3 Installation of the CPU and Heatsink

Before installing the CPU, please comply with the following conditions:1. Please make sure that the motherboard supports the CPU.2. Please take note of the one indented corner of the CPU. If you install the CPU in the wrong

direction, the CPU will not insert properly. If this occurs, please change the insert directionof the CPU.

3. Please add an even layer of heat sink paste between the CPU and heatsink.4. Please make sure the heatsink is installed on the CPU prior to system use, otherwise

overheating and permanent damage of the CPU may occur.5. Please set the CPU host frequency in accordance with the processor specifications. It is not

recommended that the system bus frequency be set beyond hardware specifications since itdoes not meet the required standards for the peripherals. If you wish to set the frequencybeyond the proper specifications, please do so according to your hardware specificationsincluding the CPU, graphics card, memory, hard drive, etc.

1-3-1 Installation of the CPU

Check the processor pins to see that none are bent. Move the socket lever to the unlocked position as shownin Figure 1.(90o to the plane of the motherboard) prior to inserting the processor. The pin 1 location isdesignated on the processor by a copper triangle that matches up to a triangle on the socket as shown inFigure 2. Align the processor to the socket and gently lower it into place. Do not force the processor into thesocket.

Fig.1Position lever at a 90 degree angle.Socket lever

Fig.2Pin 1 location on the socket and processor.Gently place the CPU into position making sure that the CPU pins fitperfectly into their holes. Once the CPU is positioned into its socket,place one finger down on the middle of the CPU and gently press themetal lever back into its original position.

Please use extra care when installing the CPU. The CPU will not fit if positioned incorrectly.Rather than applying force, please change the positioning of the CPU.


English

1-3-2 Installation of the Heatsink

The heat sink may adhere to the CPU as a result of hardening of the heat sink paste. To preventsuch an occurrence, it is suggested that either thermal tape rather than heat sink paste be used forheat dissipation or using extreme care when removing the heat sink.

Fig.1Before installing the heat sink, please first add an even layer of heat sinkpaste on the surface of the CPU. Install all the heat sink components (Pleaserefer to the heat sink manual for detailed installation instructions).

Fig.2Please connect the heat sink power connector to the CPU_FAN connectorlocated on the motherboard so that the heat sink can properly function toprevent CPU overheating.


Engl

ish Before installing the memory modules, please comply with the following conditions:1. Please make sure that the memory used is supported by the motherboard. It is

recommended that memory of similar capacity, specifications and brand be used.2. Before installing or removing memory modules, please make sure that the computer power

is switched off to prevent hardware damage.3. Memory modules have a foolproof insertion design. A memory module can be installed in

only one direction. If you are unable to insert the module, please switch the direction.

1-4 Installation of Memory

The motherboard supports DDR memory modules, whereby BIOS will automatically detect memory capacityand specifications. Memory modules are designed so that they can be inserted only in one direction. Thememory capacity used can differ with each slot.

Notch

DDR

Fig.1The DIMM socket has a notch, so the DIMM memory module canonly fit in one direction. Insert the DIMM memory module verticallyinto the DIMM socket. Then push it down.

Fig.2Close the plastic clip at both edges of the DIMM sockets to lock theDIMM module.Reverse the installation steps when you wish to remove the DIMMmodule.


English

1-5 Installation of Expansion CardsYou can install your expansion card by following the steps outlined below:1. Read the related expansion card's instruction document before install the expansion card into the

computer.2. Remove your computer's chassis cover, screws and slot bracket from the computer.3. Press the expansion card firmly into expansion slot in motherboard.4. Be sure the metal contacts on the card are indeed seated in the slot.5. Replace the screw to secure the slot bracket of the expansion card.6. Replace your computer's chassis cover.7. Power on the computer, if necessary, setup BIOS utility of expansion card from BIOS.8. Install related driver from the operating system.

Installing a AGP expansion card:

Please carefully pull out the small white-drawable bar at the end of the AGP slotwhen you try to install/uninstall the VGAcard. Please align the VGA card to theonboard AGP slot and press firmly down onthe slot. Make sure your VGA card is lockedby the small white-drawable bar.


Engl

ish

1-6 I/O Back Panel Introduction

PS/2 Keyboard and PS/2 Mouse ConnectorTo install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboard to thelower port (purple).USB portBefore you connect your device(s) into USB connector(s), please make sure your device(s) such asUSB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface. Also make sureyour OS supports USB controller. If your OS does not support USB controller, please contact OSvendor for possible patch or driver upgrade. For more information please contact your OS or device(s)vendors.Parallel PortThe parallel port allows connection of a printer, scanner and other peripheral devices.COM A (Serial Port)Connects to serial-based mouse or data processing devices.VGA PortMonitor can be connected to VGA port.LAN PortThe provided Internet connection is fast Ethernet, providing data transfer speeds of 10/100Mbps.Line InDevices like CD-ROM, walkman etc. can be connected to Line In jack.Line Out (Front Speaker Out)Connect the stereo speakers, earphone or front surround channels to this connector.MIC InMicrophone can be connected to MIC In jack.

You can use audio software to configure 2-/4-/6- channel audio functioning.


English

1-7 Connectors Introduction

1) ATX_12V2) ATX (Power Connector)3) CPU_FAN4) SYS_FAN5) FDD6) IDE1 / IDE27) SATA0 / SATA18) F_PANEL9) PWR_LED

10) F_AUDO11) CD_IN12) SPDIF_IO13) F_USB1 / F_USB214) IR15) COMB16) CLR_CMOS17) BAT

3

1

2

816

13 1715

5

4

6

7

912

11

14

10


Engl

ish

1/2) ATX_12V / ATX (Power Connector)With the use of the power connector, the power supply can supply enough stable power to all thecomponents on the motherboard. Before connecting the power connector, please make sure that allcomponents and devices are properly installed. Align the power connector with its proper location onthe motherboard and connect tightly.The ATX_12V power connector mainly supplies power to the CPU. If the ATX_12V power connector is not connected, the system will not start.Caution!Please use a power supply that is able to handle the system voltage requirements. It isrecommended that a power supply that can withstand high power consumption be used (300W orgreater). If a power supply is used that does not provide the required power, the result can lead to anunstable system or a system that is unable to start.

13

24 Pin No. Definition1 GND2 GND3 +12V4 +12V

20

111

10

Pin No. Definition1 3.3V2 3.3V3 GND4 VCC5 GND6 VCC7 GND8 Power Good9 5V SB (stand by +5V)10 +12V11 3.3V12 -12V13 GND14 PS_ON(soft on/off)15 GND16 GND17 GND18 -5V19 +5V20 +5V


English

3/4) CPU_FAN / SYS_FAN (Cooler Fan Power Connector)The cooler fan power connector supplies a +12V power voltage via a 3-pin power connector andpossesses a foolproof connection design.Most coolers are designed with color-coded power connector wires. A red power connector wireindicates a positive connection and requires a +12V power voltage. The black connector wire is theground wire (GND).Please remember to connect the power to the cooler to prevent system overheating and failure.Caution!Please remember to connect the power to the CPU fan to prevent CPU overheating and failure.

SYS_FAN

CPU_FAN

1 Pin No. Definition1 GND2 +12V3 Sense

1

5) FDD (FDD Connector)The FDD connector is used to connect the FDD cable while the other end of the cable connects to theFDD drive. The types of FDD drives supported are: 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB.Before attaching the FDD cable, please take note of the foolproof groove in the FDD connector.

2

34

1

33


Engl

ish

6) IDE1 / IDE2 (IDE Connector)An IDE device connects to the computer via an IDE connector. One IDE connector can connect to oneIDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical drive). Ifyou wish to connect two IDE devices, please set the jumper on one IDE device as Master and the otheras Slave (for information on settings, please refer to the instructions located on the IDE device).Before attaching the IDE cable, please take note of the foolproof groove in the IDE connector.

7) SATA0 / SATA1 (Serial ATA Connector)Serial ATA can provide up to150MB/s transfer rate. Please refer to the BIOS setting for the Serial ATAand install the proper driver in order to work properly.

Pin No. Definition1 GND2 TXP3 TXN4 GND5 RXN6 RXP7 GND

1 7

2

40

1

39

IDE2 IDE1


English

8) F_PANEL (Front Panel Jumper)Please connect the power LED, PC speaker, reset switch and power switch etc of your chassis frontpanel to the F_PANEL connector according to the pin assignment below.

HD (IDE Hard Disk Active LED) Pin 1: LED anode(+)Pin 2: LED cathode(-)

SPEAK (Speaker Connector) Pin 1: PowerPin 2- Pin 3: NCPin 4: Data(-)

RES (Reset Switch) Open: NormalClose: Reset Hardware System

PW (Power Switch) Open: NormalClose: Power On/Off

MSG(Message LED/Power/Sleep LED) Pin 1: LED anode(+)Pin 2: LED cathode(-)

NC NC

12

1920

HD-HD+

RES+RES-

NC

SPEAK-

MSG-MSG+

PW-PW+

SPEAK+

Message LED/Power/

Sleep LED

Power Switch

Speaker Connector

IDE Hard DiskActive LED

Reset Switch


Engl

ish

9) PWR_LEDThe PWR_LED connector is connected with the system power indicator to indicate whether thesystem is on/off. It will blink when the system enters suspend mode.

1Pin No. Definition

1 MPD+2 MPD-3 MPD-

10) F_AUDIO (Front Audio Panel Connector)If you want to use Front Audio connector, you must remove 5-6, 9-10 Jumper.In order to utilize the front audio header, your chassis must have front audio connector. Also pleasemake sure the pin assignments for the cable are the same as the pin assignments for the front audioheader. To find out if the chassis you are buying support front audio connector, please contact yourdealer. Please note, you can have the alternative of using front audio connector or of using rear audioconnector to play sound.

Pin No. Definition1 MIC2 GND3 MIC_BIAS4 POWER5 FrontAudio(R)6 Rear Audio (R)/ Return R7 NC8 No Pin9 FrontAudio (L)10 Rear Audio (L)/ Return L

1

109

2


English

11) CD_IN (CD In Connector)Connect CD-ROM or DVD-ROM audio out to the connector.

Pin No. Definition1 CD-L2 GND3 GND4 CD-R

1

12) SPDIF_IO (SPDIF In/ Out)The SPDIF output is capable of providing digital audio to external speakers or compressed AC3 data toan external Dolby Digital Decoder. Use this feature only when your stereo system has digital inputfunction. Use SPDIF IN feature only when your device has digital output function.Be careful with the polarity of the SPDIF_IO connector. Check the pin assignment carefully while youconnect the SPDIF cable. Incorrect connection between the cable and connector will make the deviceunable to work or even damage it. For optional SPDIF cable, please contact your local dealer.

1

6

2

5

Pin No. Definition1 Power2 No Pin3 SPDIF4 SPDIFI5 GND6 GND


Engl

ish

13) F_ USB1 / F_USB2 (Front USB Connector)Be careful with the polarity of the front USB connector. Check the pin assignment carefully while youconnect the front USB cable, incorrect connection between the cable and connector will make thedevice unable to work or even damage it. For optional front USB cable, please contact your local dealer.

1 9

2 10

14) IRBe careful with the polarity of the IR connector while you connect the IR. Please contact yournearest dealer for optional IR device.

1

Pin No. Definition1 Power2 Power3 USB DX-4 USB Dy-5 USB DX+6 USB Dy+7 GND8 GND9 No Pin10 NC

Pin No. Definition1 Power2 No Pin3 IR RX4 GND5 IR TX


English

15) COMB (COMB Connector)Be careful with the polarity of the COMB connector. Check the pin assignments while you connectthe COMB cable. Please contact your nearest dealer for optional COMB cable.

Pin No. Definition1 NDCDB-2 NSINB3 NSOUTB4 NDTRB-5 GND6 NDSRB-7 NRTSB-8 NCTSB-9 NRIB-10 No Pin

10

9

2

1

16) CLR_CMOS (Clear CMOS)You may clear the CMOS data to its default values by this jumper. To clear CMOS, temporarilyshort 1-2 pin. Default doesn't include the "Shunter" to prevent from improper use this jumper.

Open: Normal

Short: Clear CMOS1

1


Engl

ish

17) BAT (Battery)

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommendedby the manufacturer.

Dispose of used batteries according to the manufacturer'sinstructions.

If you want to erase CMOS...1. Turn off the computer and unplug the power cord.2. Gently take out the battery and put it aside for about one minute.

(Or you can use a metal object to connect the positive andnegative pins in the battery holder to makethem short for fiveseconds.)

3. Re-install the battery.4. Plug the power cord in and turn on the computer.

BIOS Setup- 27 -

EnglishBIOS (Basic Input and Output System) includes a CMOS SETUP utility which allows user to configurerequired settings or to activate certain system features.The CMOS SETUP saves the configuration in the CMOS SRAM of the motherboard.When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOSSRAM.When the power is turned on, pushing the <Del> button during the BIOS POST (Power-On Self Test) willtake you to the CMOS SETUP screen. You can enter the BIOS setup screen by pressing "Ctrl + F1".When setting up BIOS for the first time, it is recommended that you save the current BIOS to a disk in theevent that BIOS needs to be reset to its original settings. If you wish to upgrade to a new BIOS, eitherGIGABYTE's Q-Flash or @BIOS utility can be used.Q-Flash allows the user to quickly and easily update or backup BIOS without entering the operating system.@BIOS is a Windows-based utility that does not require users to boot to DOS before upgrading BIOS butdirectly download and update BIOS from the Internet.

CONTROL KEYS< > < > < > < > Move to select item<Enter> Select Item<Esc> Main Menu - Quit and not save changes into CMOS Status Page Setup Menu

and Option Page Setup Menu - Exit current page and return to Main Menu<Page Up> Increase the numeric value or make changes<Page Down> Decrease the numeric value or make changes<F1> General help, only for Status Page Setup Menu and Option Page Setup Menu<F2> Item Help<F5> Restore the previous CMOS value from CMOS, only for Option Page Setup Menu<F6> Load the fail-safe default CMOS value from BIOS default table<F7> Load the Optimized Defaults<F8> Q-Flash utility<F9> System Information<F10> Save all the CMOS changes, only for Main Menu

Main MenuThe on-line description of the highlighted setup function is displayed at the bottom of the screen.Status Page Setup Menu / Option Page Setup MenuPress <F1> to pop up a small help window that describes the appropriate keys to use and the possibleselections for the highlighted item. To exit the Help Window press <Esc>.

Chapter 2 BIOS Setup


Engl

ish

The Main Menu (For example: BIOS Ver. : D1)Once you enter Award BIOS CMOS Setup Utility, the Main Menu (as figure below) will appear on the screen.Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu.

Standard CMOS FeaturesThis setup page includes all the items in standard compatible BIOS.Advanced BIOS FeaturesThis setup page includes all the items of Award special enhanced features.Integrated PeripheralsThis setup page includes all onboard peripherals.Power Management SetupThis setup page includes all the items of Green function features.PnP/PCI ConfigurationThis setup page includes all the configurations of PCI & PnP ISA resources.PC Health StatusThis setup page is the System auto detect Temperature, voltage, fan, speed.Frequency/Voltage ControlThis setup page is control CPU’s clock and frequency ratio.Load Fail-Safe DefaultsFail-Safe Defaults indicates the value of the system parameters which the system would be in safeconfiguration.

If you can't find the setting you want, please press "Ctrl+F1" to search the advanced option hidden.

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

Standard CMOS FeaturesAdvanced BIOS FeaturesIntegrated PeripheralsPower Management SetupPnP/PCI ConfigurationsPC Health StatusFrequency/Voltage Control

Load Fail-Safe DefaultsLoad Optimized DefaultsSet Supervisor PasswordSet User PasswordSave & Exit SetupExit Without Saving

ESC: Quit : Select ItemF8: Q-Flash F10: Save & Exit Setup

Time, Date, Hard Disk Type...

The BIOS Setup menus described in this chapter are for reference only and may differ from theexact settings for your motherboard.

BIOS Setup- 29 -

English

Load Optimized DefaultsOptimized Defaults indicates the value of the system parameters which the system would be in bestperformance configuration.Set Supervisor PasswordChange, set, or disable password. It allows you to limit access to the system and Setup, or just to Setup.Set User PasswordChange, set, or disable password. It allows you to limit access to the system.Save & Exit SetupSave CMOS value settings to CMOS and exit setup.Exit Without SavingAbandon all CMOS value changes and exit setup.


Engl

ish

2-1 Standard CMOS Features

DateThe date format is <week>, <month>, <day>, <year>.

Week The week, from Sun to Sat, determined by the BIOS and is display onlyMonth The month, Jan. Through Dec.Day The day, from 1 to 31 (or the maximum allowed in the month)Year The year, from 1999 through 2098

TimeThe times format in <hour> <minute> <second>. The time is calculated base on the 24-hour military-time clock. For example, 1 p.m. is 13:00:00.IDE Channel 0/1 Master, Slave

IDE HDD Auto-Detection Press "Enter" to select this option for automatic device detection.IDE Device Setup. You can use one of three methods:

Auto Allows BIOS to automatically detect IDE devices during POST.(default)None Select this if no IDE devices are used and the system will skip the automatic

detection step and allow for faster system start up.Manual User can manually input the correct settings

Access Mode Use this to set the access mode for the hard drive. The four options are:CHS/LBA/Large/Auto(default:Auto)

IDE Channel 2/3 MasterIDE HDD Auto-Detection Press "Enter" to select this option for automatic device detection.Extended IDE Drive SATA devices setup. You can use one of two methods:

Auto Allows BIOS to automatically detect SATA IDE devices during POST.(Default value)

None Select this if no SATA IDE devices are used and the system will skip theautomatic detection step and allow for faster system start up.

Access Mode Use this to set the access mode for the hard drive. The two options are:Large/Auto(default:Auto)

CMOS Setup Utility-Copyright (C) 1984-2005 Award SoftwareStandard CMOS Features

Date (mm:dd:yy) Wed, May 11 2005Time (hh:mm:ss) 10:40:9

IDE Channel 0 Master [None]IDE Channel 0 Slave [None]IDE Channel 1 Master [None]IDE Channel 1 Slave [None]IDE Channel 2 Master [None]IDE Channel 3 Master [None]

Drive A [1.44M, 3.5"]Drive B [None]Floppy 3 Mode Suport [Disabled]

Holt On [All, But Keyboard]

Base Memory 640KExtended Memory 127MTotal Memory 128M

: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General HelpF5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

Item HelpMenu LevelChange the day, month,year

<Week>Sun. to Sat.

<Month>Jan. to Dec.

<Day>1 to 31 (or maximumallowed in the month)

<Year>1999 to 2098

BIOS Setup- 31 -

English

Capacity Capacity of currently installed hard disk.Hard drive information should be labeled on the outside drive casing. Enter the appropriate optionbased on this information.

Cylinder Number of cylindersHead Number of headsPrecomp Write precompLanding Zone Landing zoneSector Number of sectors

Drive A / Drive BThe category identifies the types of floppy disk drive A or drive B that has been installed in thecomputer.

None No floppy drive installed360K, 5.25" 5.25 inch PC-type standard drive; 360K byte capacity.1.2M, 5.25" 5.25 inch AT-type high-density drive; 1.2M byte capacity

(3.5 inch when 3 Mode is Enabled).720K, 3.5" 3.5 inch double-sided drive; 720K byte capacity1.44M, 3.5" 3.5 inch double-sided drive; 1.44M byte capacity. (Default value)2.88M, 3.5" 3.5 inch double-sided drive; 2.88M byte capacity.

Floppy 3 Mode Support (for Japan Area)Disabled Normal Floppy Drive. (Default value)Drive A Drive A is 3 mode Floppy Drive.Drive B Drive B is 3 mode Floppy Drive.Both Drive A & B are 3 mode Floppy Drives.

Halt onThe category determines whether the computer will stop if an error is detected during power up.

No Errors The system boot will not stop for any error that may be detected and youwill be prompted.

All Errors Whenever the BIOS detects a non-fatal error the system will be stopped.All, But Keyboard The system boot will not stop for a keyboard error; it will stop for all other

errors. (Default value)All, But Diskette The system boot will not stop for a disk error; it will stop for all other errors.All, But Disk/Key The system boot will not stop for a keyboard or disk error; it will stop for all

other errors.MemoryThe category is display-only which is determined by POST (Power On Self Test) of the BIOS.

Base MemoryThe POST of the BIOS will determine the amount of base (or conventional) memory installedin the system.The value of the base memory is typically 512K for systems with 512K memory installed onthe motherboard, or 640K for systems with 640K or more memory installed on the motherboard.

Extended MemoryThe BIOS determines how much extended memory is present during the POST.This is the amount of memory located above 1 MB in the CPU's memory address map.

Total MemoryThis item displays the memory size that used.


Engl

ish

2-2 Advanced BIOS Features

Hard Disk Boot PrioritySelect boot sequence for onboard(or add-on cards) SCSI, RAID, etc.Use < > or < > to select a device, then press<+> to move it up, or <-> to move it down the list. Press<ESC> to exit this menu.First / Second / Third Boot Device

Floppy Select your boot device priority by Floppy.LS120 Select your boot device priority by LS120.Hard Disk Select your boot device priority by Hard Disk.CDROM Select your boot device priority by CDROM.ZIP Select your boot device priority by ZIP.USB-FDD Select your boot device priority by USB-FDD.USB-ZIP Select your boot device priority by USB-ZIP.USB-CDROM Select your boot device priority by USB-CDROM.USB-HDD Select your boot device priority by USB-HDD.Legacy LAN Select your boot device priority by Legacy LAN.Disabled Disable this function.

Password CheckSystem The system can not boot and can not access to Setup page will be denied if the

correct password is not entered at the prompt.Setup The system will boot, but access to Setup will be denied if the correct password is

not entered at the prompt. (Default value)

CMOS Setup Utility-Copyright (C) 1984-2005 Award SoftwareAdvanced BIOS Features

Hard Disk Boot Priority [Press Enter]First Boot Device [Floppy]Second Boot Device [Hard Disk]Third Boot Device [CDROM] Password Check [Setup]


Item HelpMenu Level

Select Hard Disk BootDevice Priority

BIOS Setup- 33 -

English

2-3 Integrated Peripherals

IDE DMA transfer accessEnabled Enable IDE DMA transfer access. (Default value)Disabled Disable this function.

On-Chip IDE Channel0Enabled Enable onboard 1st channel IDE port. (Default value)Disabled Disable onboard 1st channel IDE port.

On-Chip IDE Channel1Enabled Enable onboard 2nd channel IDE port. (Default value)Disabled Disable onboard 2nd channel IDE port.

CMOS Setup Utility-Copyright (C) 1984-2005 Award SoftwareIntegrated Peripherals

IDE DMA transfer access [Enabled]On-Chip IDE Channel 0 [Enabled]On-Chip IDE Channel 1 [Enabled]OnChip Serial ATA [Enabled]SATA Mode [RAID]AC97 Audio [Auto]VIA Onboard LAN [Enabled]USB 1.1 Controller [Enabled]USB 2.0 Controller [Enabled]USB Keyboard Support [Disabled]USB Mouse Support [Disabled]On-Chip LAN Boot ROM [Disabled]Onboard FDC Controller [Enabled]Onboard Serial Port 1 [3F8/IRQ4]Onboard Serial Port 2 [2F8/IRQ3]UART Mode Select [Normal]

x UR2 Duplex Mode HalfOnboard Parallel Port [378/IRQ7]Parallel Port Mode [SPP]


Item HelpMenu Level

CMOS Setup Utility-Copyright (C) 1984-2005 Award SoftwareIntegrated Peripherals


Item HelpMenu Level

Midi Port Address [Disabled]x Midi Port IRQ 10


Engl

ish

OnChip Serial ATAEnabled Enable VT8237R / VT8237R+ Serial ATA supported. (Default value)Disabled Disable VT8237R / VT8237R+ Serial ATA supported.

SATA ModeRAID Set onboard SATA mode to RAID. (Default value)IDE Set onboard SATA mode to IDE.

AC97 AudioAuto Enable onboard AC'97 audio function. (Default value)Disabled Disable this function.

VIA Onboard LANEnabled Enable VIA onboard LAN function. (Default value)Disabled Disable this function.

USB 1.1 ControllerDisabled Disable USB 1.1 controller.Enabled Enable USB 1.1 controller. (Default value)

USB 2.0 ControllerDisabled Disable USB 2.0 controller.Enabled Enable USB 2.0 controller. (Default value)

USB Keyboard SupportEnabled Enable USB keyboard support.Disabled Disable USB keyboard support. (Default value)

USB Mouse SupportEnabled Enable USB mouse support.Disabled Disable USB mouse support. (Default value)

On-Chip LAN Boot ROMThis function decide whether to invoke the boot ROM of the onboard LAN chip.

PXE Set On-Chip LAN Boot ROM to PXE.RPL Set On-Chip LAN Boot ROM to RPL.Disabled Disable this function. (Default value)

Onboard FDC ControllerEnabled Enable onboard FDC Controller. (Default value)Disabled Disable onboard FDC Controller.

Onboard Serial Port 1Auto BIOS will automatically setup the Serial port 1 address.3F8/IRQ4 Enable onboard Serial port 1 and address is 3F8/IRQ4. (Default value)2F8/IRQ3 Enable onboard Serial port 1 and address is 2F8/IRQ3.3E8/IRQ4 Enable onboard Serial port 1 and address is 3E8/IRQ4.2E8/IRQ3 Enable onboard Serial port 1 and address is 2E8/IRQ3.Disabled Disable onboard Serial port 1.

BIOS Setup- 35 -

English

Onboard Serial Port 2Auto BIOS will automatically set up the Serial port 2 address.3F8/IRQ4 Enable onboard Serial port 2 and address is 3F8/IRQ4.2F8/IRQ3 Enable onboard Serial port 2 and address is 2F8/IRQ3. (Default value)3E8/IRQ4 Enable onboard Serial port 2 and address is 3E8/IRQ4.2E8/IRQ3 Enable onboard Serial port 2 and address is 2E8/IRQ3.Disabled Disable onboard Serial port 2.

UART Mode SelectThis item allows you to determine which Infra Red(IR) function of Onboard I/O chip.

Normal Set onboard I/O chip UART to Normal mode.(Default value)IrDA Set onboard I/O chip UART to IrDA mode.ASKIR Set onboard I/O chip UART to ASKIR mode.

UR2 Duplex ModeThis feature allows you to select IR mode.This function is available only when UART Mode Select is not set to Normal.

Half IR Function Duplex Half. (Default value)Full IR Function Duplex Full.

Onboard Parallel PortDisabled Disable onboard LPT port.378/IRQ7 Enable onboard LPT port and address is 378/IRQ7. (Default value)278/IRQ5 Enable onboard LPT port and address is 278/IRQ5.3BC/IRQ7 Enable onboard LPT port and address is 3BC/IRQ7.

Parallel Port ModeSPP Using Parallel port as Standard Parallel Port. (Default value)EPP Using Parallel port as Enhanced Parallel Port.ECP Using Parallel port as Extended Capabilities Port.ECP+EPP Using Parallel port as ECP and EPP mode.

Midi Port Address300 Set Midi Port Address to 300.330 Set Midi Port Address to 330Disabled Disable this function. (Default value)

Midi Port IRQ5 Set Midi Port IRQ to 5.10 Set Midi Port IRQ to 10. (Default value)


Engl

ish

2-4 Power Management Setup

ACPI Suspend TypeS1(POS) Set ACPI suspend type to S1/POS(Power On Suspend). (Default value)S3(STR) Set ACPI suspend type to S3/STR(Suspend To RAM).

USB Device Wake-Up From S3Disabled Disable USB Device Wake-Up from S3. (Default value)Enabled Enable USB Device Wake-Up from S3.

Soft-Off by PWRBTNInstant-Off Press power button then Power off instantly. (Default value)Delay 4 Sec. Press power button 4 sec. to Power off. Enter suspend if button is pressed

less than 4 sec.AC BACK Function

Memory When AC-power back to the system, the system will be back to the last statebefore AC-power is lost.

Soft-Off When AC-power back to the system, the system will be in "Off" state.(Default value)

Full-On When AC-power back to the system, the system always in "On" state.Keyboard Power On

Password Enter from 1 to 8 characters to set the Keyboard Power On Password.Disabled Disabled this function. (Default value)Keyboard 98 If your keyboard have "POWER Key" button, you can press the key to power

on the system.

CMOS Setup Utility-Copyright (C) 1984-2005 Award SoftwarePower Management Setup

ACPI Suspend Type [S1(POS)]x USB Device Wake-Up From S3 Disabled

Soft-Off by PWRBTN [Instant-Off]AC Back Function [Soft-Off]Keyboard Power On [Disabled]Mouse Power On [Disabled]PME Event Wake Up [Enabled]Modem Ring Resume [Enabled]Resume by Alarm [Disabled]

x Date (of Month) Alarm Everydayx Time (hh:mm:ss) Alarm 0 : 0 : 0


Item HelpMenu Level

[S1]Set suspend type toPower On Suspend underACPI OS

[S3]Set suspend type toSuspend to RAM underACPI OS

BIOS Setup- 37 -

English

Mouse Power OnDisabled Disabled this function. (Default value)Enabled Double click on PS/2 mouse left button to power on the system.

PME Event Wake UpThis feature requires an ATX power supply that provides at least 1A on the 5VSB lead.

Disabled Disable this function.Enabled Enable PME as wake up event. (Default value)

Modem Ring ResumeAn incoming call via modem can awake the system from any suspend state.

Disabled Disable Modem Ring Resume function.Enabled Enable Modem Ring Resume function. (Default value)

Resume by AlarmYou can set "Resume by Alarm" item to enabled and key in Date/Time to power on system.

Disabled Disable this function. (Default value)Enabled Enable alarm function to POWER ON system.

If Resume by Alarm is Enabled.Date (of Month) Alarm : Everyday, 1~31Time (hh: mm: ss) Alarm: (0~23) : (0~59) : (0~59)


Engl

ish

2-5 PnP/PCI Configurations

PCI 1 IRQ AssignmentAuto Auto assign IRQ to PCI 1. (Default value)3,4,5,7,9,10,11,12,14,15 Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 1.



CMOS Setup Utility-Copyright (C) 1984-2005 Award SoftwarePnP/PCI Configurations

PCI 1 IRQ Assignment [Auto]PCI 2 IRQ Assignment [Auto]PCI 3 IRQ Assignment [Auto]


Item HelpMenu Level

BIOS Setup- 39 -

English

2-6 PC Health Status

Current Voltage(V) Vcore / DDR25V / +3.3V / +12VDetect system's voltage status automatically.

Current CPU TemperatureDetect CPU temperature automatically.

Current CPU/SYSTEM FAN Speed (RPM)Detect CPU/SYSTEM fan speed status automatically.

CPU FAN Fail WarningDisabled Disable CPU fan fail warning function. (Default value)Enabled Enable CPU fan fail warning function.

SYSTEM FAN Fail WarningDisabled Disable SYSTEM fan fail warning function. (Default value)Enabled Enable SYSTEM fan fail warning function.

CMOS Setup Utility-Copyright (C) 1984-2005 Award SoftwarePC Health Status

Vcore OKDDR25V OK+3.3V OK+12V OKCurrent CPU Temperature 35°CCurrent CPU FAN Speed 3125 RPMCurrent SYSTEM FAN Speed 0 RPMCPU FAN Fail Warning [Disabled]SYSTEM FAN Fail Warning [Disabled]


Item HelpMenu Level


Engl

ish

2-7 Frequency / Voltage Control

K8 CPU Clock RatioDefault Set K8 CPU Clock Ratio to CPU factory default. (Default value)x4 800Mhz ~ x10 2000Mhz Set K8 CPU Clock Ratio from x4 800Mhz to x10 2000Mhz.

CPU Host Clock ControlNote: Please note that if your system is overclocked and cannot restart, please wait 20secs.for automatic system restart or clear the CMOS setup data and perform a safe restart.

Disabled Disable CPU Host Clock Control.(Default value)Enabled Enable CPU Host Clock Control.

CPU Host Frequency (Mhz)200MHz ~455MHz Set CPU Host Frequency from 200MHz to 455MHz.

PCI /AGP Frequency(Mhz)The values depend on CPU Host Frequency(Mhz).

CPU OverVoltage ControlAuto BIOS will automatically detect CPU voltage. (Default value)+5% Set CPU OverVoltage Control to +5%.+7.5% Set CPU OverVoltage Control to +7.5%.+10% Set CPU OverVoltage Control to +10%.

Incorrect using it may cause your system broken. For power End-User use only!AGP OverVoltage Control

Auto BIOS will automatically detect AGP voltage. (Default value)+0.1V Set AGP OverVoltage Control to +0.1V.+0.2V Set AGP OverVoltage Control to +0.2V.

Increase AGP voltage may get stable for Over_Clock. But it may damage to AGP Card whenenable this feature.

Incorrect using these features may cause your system broken. For power end-user use only.

CMOS Setup Utility-Copyright (C) 1984-2005 Award SoftwareFrequency/Voltage Control

K8 CPU Clock Ratio [Default]CPU Host Clock Control [Disabled]

x CPU Host Frequency 200PCI/AGP Frequency 33/66CPU OverVoltage Control [Auto]AGP OverVoltage Control [Audo]


Item HelpMenu Level

BIOS Setup- 41 -

English

2-8 Load Fail-Safe Defaults

Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimum systemperformance.




Load Fail-Safe Defaults


Load Fail-Safe Defaults (Y/N)? N

2-9 Load Optimized Defaults

Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automaticallydetects.




Load Optimized Defaults


Load Optimized Defaults (Y/N)? N


Engl

ish

2-10 Set Supervisor/User Password

When you select this function, the following message will appear at the center of the screen to assist you increating a password.Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the password.Type the password again and press <Enter>. You may also press <Esc> to abort the selection and not entera password.To disable password, just press <Enter> when you are prompted to enter password. A message"PASSWORD DISABLED" will appear to confirm the password being disabled. Once the password is disabled,the system will boot and you can enter Setup freely.The BIOS Setup program allows you to specify two separate passwords:SUPERVISOR PASSWORD and a USER PASSWORD. When disabled, anyone may access all BIOS Setupprogram function. When enabled, the Supervisor password is required for entering the BIOS Setup programand having full configuration fields, the User password is required to access only basic items.If you select "System" at "Password Check" in Advance BIOS Features Menu, you will be prompted for thepassword every time the system is rebooted or any time you try to enter Setup Menu.If you select "Setup" at "Password Check" in Advance BIOS Features Menu, you will be prompted only whenyou try to enter Setup.




Change/Set/Disable Password


Enter Password:

BIOS Setup- 43 -

English

2-11 Save & Exit Setup

Type "Y" will quit the Setup Utility and save the user setup value to RTC CMOS.Type "N" will return to Setup Utility.

2-12 Exit Without Saving

Type "Y" will quit the Setup Utility without saving to RTC CMOS.Type "N" will return to Setup Utility.




Save Data to CMOS

Load Fail-Safe DefaultsLoad Optimized DefaultsSet Supervisor PasswordSet User PasswordSave & Exit SetupExit Without SavingSave to CMOS and EXIT (Y/N)? Y




Abandon all Data


Quit Without Saving (Y/N)? N


Engl

ish

Drivers Installation- 45 -

EnglishPictures below are shown in Windows XP.Insert the driver CD-title that came with your motherboard into your CD-ROM drive, the driverCD-title will auto start and show the installation guide. If not, please double click the CD-ROMdevice icon in "My computer", and execute the Setup.exe.

Chapter 3Drivers Installation

3-1 Install Chipset DriversAfter insert the driver CD, "Xpress Install" will scan automatically the system and then list all the drivers thatrecommended to install. The "Xpress Install" uses the"Click and Go" technology to install the driversautomatically. Just select the drivers you want then click the "GO" button. The "Xpress Install" will executethe installation for you automatically.

Some device drivers will restart your system automatically. After restarting your system the "XpressInstall" will continue to install other drivers.System will reboot automatically after install the drivers, afterward you can install others application.

For USB2.0 driver support under Windows XP operating system, please use Windows ServicePack. After install Windows Service Pack, it will show a question mark "?" in "Universal Serial Buscontroller" under "Device Manager". Please remove the question mark and restart the system(System will auto-detect the right USB2.0 driver).


Engl

ish

3-2 Software ApplicationThis page displays all the tools that Gigabyte developed and some free software. You can click an item toinstall it.

3-3 Software InformationThis page lists the contents of software and drivers in this CD-title.

Drivers Installation- 47 -

English

3-4 Hardware InformationThis page lists all device you have for this motherboard.

3-5 Contact UsPlease see the last page for details.


Engl

ish

Appendix- 49 -

English

Chapter 4 Appendix4-1 Unique Software Utilities

M.I.T. (Motherboard Intelligent Tweaker)Motherboard Intelligent Tweaker (M.I.T.) allows user to access and change BIOS featuresettings with relative speed and ease. Through GIGABYTE M.I.T. feature the user is nolonger required to switch into different modes within BIOS setup in order to change systemsettings such as the CPU system bus, memory timings or to enabled Gigabyte's uniqueC.I.A. 2 and M.I.B. 2 features. M.I.T.'s integration of all platform performance settings intoa single mode now gives any user the ability to control and enhance their computer systemto the desired level.

C.I.A.2 (CPU Intelligent Accelerator 2)GIGABYTE CPU Intelligent Accelerator 2(C.I.A. 2) is designed to automatically adjust CPUcomputing power to maximize system performance. When enabled, the program detectsthe current CPU loading and automatically accelerates the CPU computing performance toallow for a faster and smoother execution of programs. When the function is disabled, theCPU is returned to its initial status.

M.I.B.2 (Memory Intelligent Booster 2)Built on the original M.I.B., the new Memory Intelligent Booster 2 (M.I.B. 2) is designedespecially to maximize memory performance and boost memory bandwidth up to 10%.With added branded memory module information, users are able to optimize memoryperformance by selecting from a recommended memory module list.

S.O.S. (System Overclock Saver)System Overclock Saver (S.O.S.) is a unique feature that eliminates system boot-up errorsresulting from system over-enhancement by the user. With GIGABYTE's proprietaryS.O.S. feature, users no longer need to open up the PC chassis and short-circuit the "ClearCMOS" pins or the battery on the motherboard to reset the system back to factory defaultsettings. Instead, S.O.S. automatically resets the overclocked system settings back to theirfactory defaults to provide a more user-friendly and reliable platform for users.

Download CenterDownload Center allows users to quickly download and update their BIOS as well as thelatest drivers for their system. Download Center automatically runs a system check of theuser PC and provides the user with the current system information as well as displaying adetailed list of all new drivers with the option for download.

C.O.M. (Corporate Online Management)A web-based system management tool that allows system hardware information such asCPU, memory, graphics card, etc. to be monitored and controlled via the Internet, C.O.M.allows corporate MIS engineers to easily maintain corporate computers such as providingthe most up-to-date drivers and BIOS. (Do not use C.O.M. and @BIOS at the same time.)

U-PLUS D.P.S. (Universal Plus Dual Power System)The U-Plus Dual Power System (U-Plus DPS) is a revolutionary eight-phase power circuitbuilt for ultimate system protection. Designed to withstand varying current levels andchanges, the U-Plus D.P.S. provides an immensely durable and stable power circuit to theCPU for solid system stability. These characteristics make it the ideal companion with thelatest LGA775 Intel® Pentium® 4 Processor as well as future Intel® processors. As well, 4blue LED's are mounted on the U-Plus D.P.S. for intelligent indication of system loading.

(Not all model support these Unique Software Utilities, please check your MB features.)


Engl

ish

4-1-1 EasyTune 5 IntroductionEasyTune 5 presents the most convenient Windows based system performance enhancement andmanageability utility. Featuring several powerful yet easy to use tools such as 1) Overclocking for enhancingsystem performance, 2) C.I.A. and M.I.B. for special enhancement for CPU and Memory, 3) Smart-Fancontrol for managing fan speed control of both CPU cooling fan and North-Bridge Chipset cooling fan, 4) PChealth for monitoring system status.(Note)

User Interface Overview

(Note) EasyTune 5 functions may vary depending on different motherboards.

Button / Display Description1. Overclocking Enters the Overclocking setting page2. C.I.A./C.I.A.2 and M.I.B./M.I.B.2 Enters the C.I.A./2 and M.I.B./2 setting page3. Smart-Fan Enters the Smart-Fan setting page4. PC Health Enters the PC Health setting page5. GO Confirmation and Execution button6. "Easy Mode" & "Advance Mode" Toggles between Easy and Advance Mode7. Display screen Display panel of CPU frequency8. Function display LEDs Shows the current functions status9. GIGABYTE Logo Log on to GIGABYTE website10. Help button Display EasyTuneTM 5 Help file11. Exit or Minimize button Quit or Minimize EasyTuneTM 5 software

Appendix- 51 -

English

4-1-2 Xpress Recovery Introduction

What is Xpress Recovery ?Xpress Recovery is a utility used to back up and restore an OS partition.If the hard drive is not working properly, the user can restore the drive toits original state.

1. Supports FAT16, FAT32, and NTFS formats2. Must be connected to the IDE1 Master3. Allows installation of only one OS4. Must be used with an IDE hard disk supporting HPA5. The first partition must be set as the boot partition. When the boot partition is backed up,

please do not alter its size.6. Xpress Recovery is recommended when using Ghost to return boot manager to NTFS

format.

How to use the Xpress Recovery1. Boot from CD-ROM (BMP Mode)

Enter the BIOS menu, select "Advanced BIOS Feature" and set to boot from CD-ROM. Insert theprovided driver CD into your CD drive, then save and exit the BIOS menu. Once the computer hasrestarted, the phrase "Boot from CD:" will appear at the bottom left-hand corner of the screen. When"Boot from CD:" appears, press any key to enter Xpress Recovery.Once you have completed this step, subsequent access to Xpress Recovery can also function bypressing the F9 key during computer power on.

Xpress Recovery V1.0 (C) Copy Right 2003. GIGABYTE Technology CO. , Ltd.

1. Execute Backup Utility2. Execute Restore Utility3. Remove Backup Image4. Set Password5. Exit and Restart

Build 2011

Boot from CD:

.

.Verifying DMI Pool DataBoot from CD:


Engl

ish

2. Press F9 during powering on the computer. (Text Mode)

Xpress Recovery V1.0 (C) Copy Right 2003. GIGABYTE Technology CO. , Ltd.

1. Execute Backup Utility2. Execute Restore Utility3. Remove Backup Image4. Set Password5. Exit and Restart

1. If you have already entered Xpress Recovery by booting from the CD-ROM, you canenter Xpress Recovery in the future by pressing the F9 key.

2. System storage capacity as well as drive reading/writing speed will affect backup speed.3. It is recommended that Xpress Recovery be immediately installed after OS and all

required driver and software installations are complete.

Award Modular BIOS v6.00PG, An Energy Star AllyCopyright (C) 1984-2004, Award Software, Inc.

Intel 865PE AGPSet BIOS for 8IPE1000MT F1Check System Health OK...

Press DEL to enter SETUP / Q-Flash, F9 For Xpress Recovery08/16/2002-I845GE-6A69YG01C-00

F9 For Xpress Recovery

Appendix- 53 -

English

1. Execute Backup Utility:Press B to Backup your System or Esc to ExitThe backup utility will automatically scan your system and back up data as a backup image in your harddrive.

Not all systems support access to Xpress Recovery by pressing the F9 key during computerpower on. If this is the case, please use the boot from CD-ROM method to enter XpressRecovery.

2. Execute Restore Utility:This program will recover your system to factory default.Press R to restore your system back to factory default or press Esc to exitRestores backup image to original state.

3. Remove Backup Image:Remove backup image. Are you sure? (Y/N)Remove the backup image.

4. Set Password:Please input a 4-16 character long password (a-z or 0-9) or press Esc to exitYou can set a password to enter Xpress Recovery to protect your hard disk data. Once this is done,password input will be required to enter Xpress Recovery during the next as well as subsequent systemrestarts. If you wish to remove the need for password entry, please select "Set Password" and under"New Password/Confirm Password", make sure there is no entry and then press "Enter" to removepassword requirement.

5. Exit and Restart:Exit and restart your computer.


Engl

ish

4-1-3 Flash BIOS Method IntroductionMethod 1 : Q-FlashTM UtilityQ-FlashTM is a BIOS flash utility embedded in Flash ROM. With this utility,users only have to stay in the BIOS menu when they want to updateBIOS. Q-Flash?allows users to flash BIOS without any utility in DOS or

Windows. Using Q-FlashTM indicating no more fooling around with any complicated instructions andoperating system since it is in the BIOS menu.

Please note that because updating BIOS has potential risk, please do it with caution!! We aresorry that Gigabyte Technology Co., Ltd is not responsible for damages of system because ofincorrect manipulation of updating BIOS to avoid any claims from end-users.

Before You Begin:Before you start updating BIOS with the Q-FlashTM utility, please follow the steps below first.

1. Download the latest BIOS for your motherboard from Gigabyte's website.2. Extract the BIOS file downloaded and save the BIOS file (the one with model name.Fxx. For

example, 8KNXPU.Fba) to a floppy disk.3. Reboot your PC and press Del to enter BIOS menu.

The BIOS upgrading guides below are separated into two parts.If your motherboard has dual-BIOS, please refer to Part One.If your motherboard has single-BIOS, please refer to Part Two.

Part One:Updating BIOS with Q-FlashTM Utility on Dual BIOS Motherboards.Some of Gigabyte motherboards are equipped with dual BIOS. In the BIOS menu of the motherboardssupporting Q-Flash and Dual BIOS, the Q-Flash utility and Dual BIOS utility are combined in the samescreen. This section only deals with how to use Q-Flash utility.In the following sections, we take GA-8KNXP Ultra as the example to guide you how to flash BIOSfrom an older version to the latest version. For example, from Fa3 to Fba.

Intel i875P AGPset BIOS for 8KNXP Ultra Fa3Check System Health OK , VCore = 1.5250Main Processor : Intel Pentium(R) 4 1.6GHz (133x12)<CPUID : 0F27 Patch ID : 0027>Memory Testing : 131072K OK

Memory Frequency 266 MHz in Single ChannelPrimary Master : FUJITSU MPE3170AT ED-03-08Primary Slave : NoneSecondary Master : CREATIVEDVD-RM DVD1242E BC101Secondary Slave : None

Press DEL to enter SETUP / Dual BIOS / Q-Flash / F9 ForXpress Recovery08/07/2003-i875P-6A79BG03C-00


The BIOS file is Fa3before updating

Appendix- 55 -

English

Entering the Q-FlashTM utility:


Standard CMOS FeaturesAdvanced BIOS FeaturesIntegrated PeripheralsPower Management SetupPnP/PCI ConfigurationsPC Health StatusMB Intelligent Tweaker(M.I.T.)

Select LanguageLoad Fail-Safe DefaultsLoad Optimized DefaultsSet Supervisor PasswordSet User PasswordSave & Exit SetupExit Without Saving

ESC: Quit F3: Change LanguageF8: Dual BIOS/Q-Flash F10: Save & Exit Setup


Step 2: Press F8 button on your keyboard and then Y button to enter the Dual BIOS/Q-Flash utility.

Step1: To use Q-Flash utility, you must press Del in the boot screen to enter BIOS menu.

Exploring the Q-FlashTM / Dual BIOS utility screenThe Q-Flash / Dual BIOS utility screen consists of the following key components.

Task menu for Dual BIOS utility:Contains the names of eight tasks and two item showing information about the BIOS ROM type. Blocking atask and pressing Enter key on your keyboard to enable execution of the task.Task menu for Q-Flash utility:Contains the names of four tasks. Blocking a task and pressing Enter key on your keyboard to enable execu-tion of the task.Action bar:Contains the names of four actions needed to operate the Q-Flash/Dual BIOS utility. Pressing the buttonsmentioned on your keyboards to perform these actions.

Dual BIOS UtilityBoot From......................................... Main BiosMain ROM Type/Size.............................SST 49LF003A 512K Backup ROM Type/Size.........................SST 49LF003A 512K

Wide Range Protection DisableBoot From Main Bios

Auto Recovery EnableHalt On Error Disable

Copy Main ROM Data to BackupLoad Default Settings

Save Settings to CMOSQ-Flash Utility

Load Main BIOS from FloppyLoad Backup BIOS from Floppy

Save Main BIOS to FloppySave Backup BIOS to Floppy

Enter : Run :Move ESC:Reset F10:Power Off

Task menu forDual BIOSutility

Task menu forQ-FlashTM utility

Dual BIOS utility bar

Q-FlashTM utility titlebar

Action bar


Engl

ish









Using the Q-FlashTM utility:This section tells you how to update BIOS using the Q-Flash utility. As described in the "Before you begin"section above, you must prepare a floppy disk having the BIOS file for your motherboard and insert it to yourcomputer. If you have already put the floppy disk into your system and have entered the Q-Flash utility,please follow the steps below to flash BIOS.

Steps:1. Press arrow buttons on your keyboard to move the light bar to "Load Main BIOS from Floppy" item in

the Q-Flash menu and press Enter button.Later, you will see a box pop up showing the BIOS files you previously downloaded to the floppy disk.

If you want to save the current BIOS for backup purpose, you can begin Step 1 with "Save MainBIOS to Floppy" item.

2. Move to the BIOS file you want to flash and press Enter. In this example, we only download one BIOS file to the floppy disk so only one BIOS file, 8KNXPU.Fba, is listed.

Please confirm again you have the correct BIOS file for your motherboard.

1 file(s) found8KNXPU.Fba 512K

Total size : 1.39M Free size : 911.50KF5 : Refresh DEL : Delete

BIOS file in the floppydisk.









Reading BIOS file from floppy ...>>>>>>>>>>>>>>.....................

Don't Turn Off Power or Reset System

Do not turn off power orreset your system at thisstage!!

After pressing Enter, you'll then see the progress of reading the BIOS file from the floppy disk.

After BIOS file is read, you'll see a confirmation dialog box asking you "Are you sure to update BIOS?"

Appendix- 57 -

English

3. Press Y button on your keyboard after you are sure to update BIOS. Then it will begin to update BIOS. The progress of updating BIOS will be displayed.









!! Copy BIOS completed - Pass !!

Please press any key to continue

Please do not take out the floppy disk when it begins flashing BIOS.

4. Press any keys to return to the Q-Flash menu when the BIOS updating procedure is completed.

You can repeat Step 1 to4 to flash the backupBIOS, too.









Are you sure to RESET ?

[Enter] to continure or [Esc] to abort...

5. Press Esc and then Y button to exit the Q-Flash utility. The computer will restart automatically afteryou exit Q-Flash.

After system reboots, you may find the BIOS version on your boot screen becomes the one you flashed.

Intel i875P AGPset BIOS for 8KNXP Ultra FbaCheck System Health OK , VCore = 1.5250Main Processor : Intel Pentium(R) 4 1.6GHz (133x12)<CPUID : 0F27 Patch ID : 0027>Memory Testing : 131072K OK

Memory Frequency 266 MHz in Single ChannelPrimary Master : FUJITSU MPE3170AT ED-03-08Primary Slave : NoneSecondary Master : CREATIVEDVD-RM DVD1242E BC101Secondary Slave : None

Press DEL to enter SETUP / Dual BIOS / Q-Flash / F9 ForXpress Recovery09/23/2003-i875P-6A79BG03C-00


The BIOS filebecomes Fab afterupdating.


Engl

ish




Load Optimized Defaults

6. Press Del to enter BIOS menu after system reboots. When you are in BIOS menu, move toLoad Optimized Defaults item and press Enter to load BIOS Optimized Defaults. Normally thesystem redetects all devices after BIOS has been upgraded. Therefore, we highly recommendreloading the BIOS defaults after BIOS has been upgraded.


Load Optimized Defaults (Y/N)? Y

Press Y on your keyboard to load defaults.




Save Data to CMOS

7. Select Save & Exit Setup item to save the settings to CMOS and exit the BIOS menu.System will reboot after you exit the BIOS menu. The procedure is completed.


Save to CMOS and EXIT (Y/N)? Y

Press Y on your keyboard to save and exit.Part Two:Updating BIOS with Q-FlashTM Utility on Single-BIOS Motherboards.This part guides users of single-BIOS motherboards how to update BIOS using the Q-FlashTM utility.



Top PerformanceLoad Fail-Safe DefaultsLoad Optimized DefaultsSet Supervisor PasswordSet User PasswordSave & Exit SetupExit Without Saving

ESC: Quit F3: Change LanguageF8: Q-Flash F10: Save & Exit Setup


Appendix- 59 -

English

Exploring the Q-FlashTM utility screenThe Q-FlashBIOS utility screen consists of the following key components.

Task menu for Q-Flash utility:Contains the names of three tasks. Blocking a task and pressing Enter key on your keyboard to enableexecution of the task.Action bar:Contains the names of four actions needed to operate the Q-Flash utility. Pressing the buttons mentioned onyour keyboards to perform these actions.Using the Q-FlashTM utility:This section tells you how to update BIOS using the Q-Flash utility. As described in the "Before you begin"section above, you must prepare a floppy disk having the BIOS file for your motherboard and insert it to yourcomputer. If you have already put the floppy disk into your system and have entered the Q-Flash utility,please follow the steps below to flash BIOS.Steps:1. Press arrow buttons on your keyboard to move the light bar to "Update BIOS from Floppy" item in the

Q-Flash menu and press Enter button.Later, you will see a box pop up showing the BIOS files you previously downloaded to the floppy disk.

If you want to save the current BIOS for backup purpose, you can begin Step 1 with "Save BIOSto Floppy" item.

2. Move to the BIOS file you want to flash and press Enter. In this example, we only download one BIOS file to the floppy disk so only one BIOS file, 8GE800.F4, is listed.

Please confirm again you have the correct BIOS file for your motherboard.

Q-Flash Utility V1.30 Flash Type/Size.................................SST 49LF003A 256K

Keep DMI Data EnableUpdate BIOS from Floppy

Save BIOS to FloppyEnter : Run :Move ESC:Reset F10:Power Off

1 file(s) found8GE800.F4 256K

Total size : 1.39M Free size : 1.14MF5 : Refresh DEL : Delete

BIOS file in the floppydisk.




Reading BIOS file from floppy ...>>>>>>>>>>>>>>.....................


Do not turn off power orreset your system atthis stage!!

After BIOS file is read, you'll see a confirmation dialog box asking you "Are you sure to update BIOS?"

Please do not take out the floppy disk when it begins flashing BIOS.




Task menu forQ-FlashTM utility

Q-FlashTM utility bar

Action bar


Engl

ish

3. Press Y button on your keyboard after you are sure to update BIOS.Then it will begin to update BIOS. The progress of updating BIOS will be shown at the same time.




Updating BIOS Now>>>>>>>>>>>>>>>>>>>.........................


Do not turn off power orreset your systemat this stage!!

4. Press any keys to return to the Q-Flash menu when the BIOS updating procedure is completed.




!! Copy BIOS completed - Pass !!

Please press any key to continue

5. Press Esc and then Y button to exit the Q-Flash utility. The computer will restart automatically afteryou exit Q-Flash.




Are you sure to RESET ?

[Enter] to continure or [Esc] to abort...

After system reboots, you may find the BIOS version on your boot screen becomes the one you flashed.

Intel 845GE AGPSet BIOS for 8GE800 F4Check System Health OKMain Processor : Intel Pentium(R) 4 1.7GHz (100x17.0)<CPUID : 0F0A Patch ID : 0009>Memory Testing : 122880K OK + 8192K Shared Memory

Primary Master : FUJITSU MPE3170AT ED-03-08Primary Slave : NoneSecondary Master : CREATIVEDVD-RM DVD1242E BC101Secondary Slave : None

Press DEL to enter SETUP / Q-Flash03/18/2003-I845GE-6A69YG01C-00


The BIOS filebecomes F4 afterupdating

6. Press Del to enter BIOS menu after system reboots and "Load BIOS Fail-Safe Defaults". See howto Load BIOS Fail-Safe Defaults, please kindly refer to Step 6 to 7 in Part One.

Congratulation!! You have updated BIOS successfully!!

Appendix- 61 -

English

Method 2 : @BIOSTM UtilityIf you do not have a DOS startup disk, we recommend that you use thenew @BIOS utility. @BIOS allows users to update their BIOS underWindows. Just select the desired @BIOS server to download the latestversion of BIOS.

1. Methods and steps:I. Update BIOS through Internet

a. Click "Internet Update" iconb. Click "Update New BIOS" iconc. Select @BIOSTM severd. Select the exact model name on your motherboarde. System will automatically download and update the BIOS.

II. Update BIOS NOT through Internet:a. Do not click "Internet Update" iconb. Click "Update New BIOS"c. Please select "All Files" in dialog box while opening the old file.d. Please search for BIOS unzip file, downloading from internet or any other methods (such as:

K8VM800M.F1).e. Complete update process following the instruction.

Fig 1. Installing the @BIOS utility Fig 2. Installation Complete and Run @BIOS

Fig 3. The @BIOS Utility Fig 4. Select the desired @BIOS server

Click Sart/ Programs/ GIGABYTE/@BIOS

Click " " Click "Update New BIOS"

Select @BIOS item


Engl

ish

III. Save BIOSIn the very beginning, there is "Save Current BIOS" icon shown in dialog box. It means to save thecurrent BIOS version.

IV. Check out supported motherboard and Flash ROM:In the very beginning, there is "About this program" icon shown in dialog box. It can help you check outwhich kind of motherboard and which brand of Flash ROM are supported.

2. Note:I. In method I, if it shows two or more motherboard's model names to be selected, please make

sure your motherboard's model name again. Selecting wrong model name will cause thesystem unbooted.

II. In method II, be sure that motherboard's model name in BIOS unzip file are the same as yourmotherboard's. Otherwise, your system won't boot.

III. In method I, if the BIOS file you need cannot be found in @BIOSTM server, please go ontoGigabyte's web site for downloading and updating it according to method II.

IV. Please note that any interruption during updating will cause system unbooted.V. Do not use @BIOS and C.O.M. (Corporate Online Management) at the same time.

Appendix- 63 -

English

4-1-4 Serial ATA BIOS Setting Utility IntroductionRAID LevelsRAID (Redundant Array of Independent Disks) is a method of combining two hard disk drives into one logicalunit. The advantage of an Array is to provide better performance or data fault tolerance. Fault tolerance isachieved through data redundant operation, where if one drives fails, a mirrored copy of the data can befound on another drive. This can prevent data loss if the operating system fails or hangs. The individual diskdrives in an array are called members. The configuration information of each member is recorded in thereserved sector that identifies the drive as a member. All disk members in a formed disk array are recognizedas a single physical drive to the operating system.Hard disk drives can be combined together through a few different methods. The different methods arereferred to as different RAID levels. Different RAID levels represent different performance levels, securitylevels and implementation costs. The RAID levels which the VIA VT8237R / VT8237R+ chipsetsupports are RAID 0, RAID 1,and JBOD.

RAID 0 (Striping)RAID 0 reads and writes sectors of data interleaved between multiple drives. If any disk member fails, itaffects the entire array. The disk array data capacity is equal to the number of drive members times thecapacity of the smallest member. The striping block size can be set from 4KB to 64KB. RAID 0 does notsupport fault tolerance.

RAID 1 (Mirroring)RAID 1 writes duplicate data onto a pair of drives and reads both sets of data in parallel. If one of themirrored drives suffers a mechanical failure or does not respond, the remaining drive will continue to function.Due to redundancy, the drive capacity of the array is the capacity of the smallest drive. Under a RAID 1setup, an extra drive called the spare drive can be attached. Such a drive will be activated to replace a faileddrive that is part of a mirrored array. Due to the fault tolerance, if any RAID 1 drive fails, data access will notbe affected as long as there are other working drives in the array.

JBOD (Spanning)A spanning disk array is equal to the sum of the all drives when the drives used are having different capacities.Spanning stores data onto a drive until it is full, then proceeds to store files onto the next drive in the array.When any disk member fails, the failure affects the entire array. JBOD is not really a RAID and does notsupport fault tolerance.


Engl

ish

Please follow the steps below to construct a complete RAID array:1) Have ready your hard drives for RAID construction.

Note: To achieve best performance, it is recommended that the hard drives used are of similar makeand storage capacity.

2) Please attach the hard drive connectors to their appropriate location on the motherboard ie. IDE, SCSI,or SATA.

3) Enter the motherboard BIOS and locate RAID setup (Please refer to the section on Integrated Peripherals).4) Enter RAID setup in the BIOS and select the RAID type (For instance, enter Tab to select

VT8237R / VT8237R+ RAID; Ctrl + S to select Silicon Image).5) Complete driver installation.6) Complete RAID utility installation.More information on steps 4 and 5 is provided. (For more detailed setup information, please visit our websiteat http:\\www.gigabyte.com.tw to read or download the information you need.)

Configuring the VT8237 SATA RAID BIOSThe RAID BIOS setup utility lets you choose the RAID array type and which hard drives you want to makepart of the array.

Entering the VT8237 SATA RAID BIOS Setup Utility1. After rebooting your computer, wait until you see the RAID software prompting you to press Tab. TheRAID prompt appears as part of the system POST and boot process prior to loading the OS. You have a fewseconds to press Tab before the window disappears.

Press Tab to enter RAID setup utility, the VT8237 SATA RAID BIOS utility screen will appear. You can pressup arrow key< > or down arrow key< > to move the selection bar and select the item that you want toexecute.

VIA Technologies, Inc. VIA VT8237 Serial ATA RAID BIOS Setting Utility V2.41Copyright (C) VIA Technologies, Inc. All Right reserved.

Scan Devices, Please wait...Press <Tab> key into User Window!Serial_Ch0 Master : ST3120026ASSerial_Ch1 Master : ST3120026AS

Create ArrayDelete ArrayCreate/Delete SpareSelect Boot ArraySerial Number View

VIA Tech. VT8237 SATA RAID BIOS Ver 2.41

Channel Drive Name Array Name Mode Size(GB) Status

Serial_Ch0 Master ST3120026AS SATA 111.79 Hdd


Create a RAID array withthe hard disks attached toVIA RAID controller

F1 : View Array/disk Status, : Move to next item

Enter : Confirm the selectionESC : Exit

Appendix- 65 -

English

A. Create Array:Press Enter on Create Array item, you will see the screen as shown below.








Auto Setup For PerformanceArray Mode RAID 0 (Striping)Select Disk DrivesBlock Size 64KStart Create Process

Before create an Array, you have to set the array mode first. Select Array Mode and press Enter, use thearrow key to select the array mode. The options are: RAID 0 for performance, RAID 1 for data protection,and RAID SPAN for capacity.








Auto Setup For Data SecurityArray Mode RAID 0 (Striping)Select Disk DrivesBlock Size 64KStart Create Process

RAID 0 for performanceRAID 1 for data protectionRAID SPAN for capacity


Engl

ish

After array mode is selected, there are two methods to create a disk array. One method is Auto Setup andthe other one is Select Disk Drives. Auto Setup allows BIOS to select the disk drives and create arraysautomatically, but it does not duplicate the mirroring drives even if the user selected Create and duplicate forRAID 1. It is recommended all disk drives are new ones when wanting to create an array. Select DiskDrives lets the user select the array drives by their requirements. Select the Select Disk Drives item andpress Enter, use the arrow key to select the hard disk. The selected hard disk will be marked a star(*) signal.

Use the arrow key to select Start Create Process and press Enter. A warning message will appear [Thedata on the selected disks will be destroied. Continue? (Y/N)], press Y to finish the creation, or press Nto cancel the creation.Important note: All existing contents in the hard drive will be destroyed after array creation.



[*]Serial_Ch0 Master ST3120026AS SATA 111.79 Stripe0






If you select a RAID 0 array, the block size of the array can also be selected. Use the arrow key to selectBlock Size and press Enter, then select a block size from the popup menu. The block size can be 4KB to64KB.









4K8K16K32K64K

Appendix- 67 -

English

B. Delete Array:If you want to delete the Array, select Delete Array in the main menu and press Enter. The channel columnwill be activated. Select the member of an array that is to be deleted and press Enter. A warning messagewill show up, press Y to delete or press N to cancel.

Deleting a disk array will destroy all the data on the disk array except RAID 1 arrays. When a RAID isdeleted, the data on these two hard disk drives will be reserved and become two normal disk drives.


Delete a RAID array containthe hard disks attached toVIA RAID controller





[*]Serial_Ch0 Master ST3120026AS ARRAY 0 SATA 111.79 Stripe0

[*]Serial_Ch1 Master ST3120026AS ARRAY 0 SATA 111.79 Stripe1

The selected array will be destoried.Are you sure? Continue? Press Y/N

C. Select Boot Array:You can select a disk array as boot device if you want to boot operating system from an array. Boot diskarray cannot be selected if the operating system does not boot from the disk array. Highlight the Select BootArray item; press Enter and the channel column will be activated. Then highlight the target disk array andpress Enter. Press Esc to go back to main menu. If you want to cancel the boot array, select the disk arraythat has a star(*) mark and press Enter, its boot setting will be canceled.


Set/Clear bootable array





[*]Serial_Ch0 Master ST3120026AS ARRAY 0 SATA 111.79 Boot

[*]Serial_Ch1 Master ST3120026AS ARRAY 0 SATA 111.79 Boot


Engl

ish

D. Serial Number View:Highlight Serial Number View and press Enter. Use arrow key to select a drive, the selected drive's serialnumber can be viewed in the last column. The serial number is assigned by the disk drive manufacturer.


View the serial number ofhard disk, it is useful foridentify same model disks





Serial_Ch0 Master ST3120026AS ARRAY 0 SATA 111.79 Stripe0

Serial_Ch1 Master ST3120026AS ARRAY 0 SATA 111.79 Stripe1

Serial Number: 3JT354CP

E. View Array Status:Press the F1 key to show the array status on the lower screen. If there are no disk arrays then nothing will bedisplayed on the screen.





Array Name Array Mode Block Size(GB) Size(GB)

ARRAY 0 Stripe 64K 223.58


Appendix- 69 -

English

Installing the RAID driversTo install operating system onto a serial ATA hard disk successfully, you need to install the SATA controllerdriver during OS installation. Without the driver, the hard disk may not be recognized during the Windowssetup process. First of all, copy the driver for the SATA controller from the motherboard driver CD-ROM to afloppy disk. See the instructions below about how to copy the driver in MS-DOS mode(Note1). Prepare a startupdisk that has CD-ROM support and a blank formatted floppy disk.

Step 1: Insert the prepared startup disk and motherboard driver CD-ROM in your system. Boot from thestartup disk. Once at the A:\> prompt, change to the CD-ROM drive (example: D:\>). At the D:\> prompt, typethe following two commands. Press ENTER after each command (Fig.1):

cd bootdrv

menu

Step 2: When the controller menu (Fig.2) appears, remove the startup disk and insert the blank formatteddisk. Select the controller driver by pressing the corresponding letter from the menu. Your system will thenautomatically zip and transfer this driver file to the floppy disk. Press 0 to exit when finished.

Fig.1 Fig. 2

Step 3: After completing the steps, boot from the Windows installation disk to install the RAID drivers.Press F6 as soon as you see the "Press F6 if you need to install a third party SCSI or RAID driver" message,then supply serial ATA controller driver by this floppy disk. Follow the on-screen instructions to complete theinstallation.

(Each time you add a new hard drive to a RAID array, the RAID driver will have to be installed underWindows once for that hard drive. After that, the driver will not have to be installed.)

(Note 1): For users without a startup disk.Use an alternative system and insert the GIGABYTE motherboard drive CD-ROM. From the CD-ROM drive (example: D:\) double click the MENU.exe file in the BootDrv folder. A command promptwindow will open similar to that in Fig. 2.


Engl

ish

4-1-5 2 / 4 / 6 Channel Audio Function Introduction

STEP 1:Connect the stereo speakers or earphone to"Line Out."

STEP 3:On the AC97 Audio Configuration menu, click theSpeaker Configuration tab and select the2-channel mode for stereo speaker output checkbox.

2 Channel Audio SetupWe recommend that you use speakers with amplifier to get the best sound effect if the stereo output isapplied.

Line Out

STEP 2:After installing the audio driver, you'll find a SoundEffect icon on the lower right hand taskbar. Clickthe icon to select the function.

Appendix- 71 -

English

4 Channel Analog Audio Output Mode

STEP 1:Connect the front channels to "Line Out,"the rear channels to "Line In."

STEP 3:On the AC97 Audio Configuration menu, click theSpeaker Configuration tab and select the 4-chan-nel mode for 4 speaker output check box.Clear the Only SURROUND-KIT check box and pressOK.

When the Environment setting is None, thesound would be performed as stereo mode(2-channel output). Please select other settings (ex:Living Room) for 4-channel output.

Line In

Line Out

STEP 2:After installing the audio driver, you'll find a Sound

Effect icon on the lower right hand taskbar. Clickthe icon to select the function.


Engl

ish Use the back audio panel to connect the audio outputwithout any additional module.STEP 1:Connect the front channels to "Line Out",the rearchannels to "Line In", and the Center/Subwoofer chan-nels to "MIC In".

Basic 6 Channel Analog Audio Output Mode

STEP 3:On the AC97 Audio Configuration menu, click theSpeaker Configuration tab and select the 6-chan-nel mode for 5.1 speaker output check box.Clear the Only SURROUND-KIT check box and pressOK.

Line Out

Line In

MIC In

STEP 2:After installing the audio driver, you'll find a SoundEffect icon on the lower right hand taskbar. Clickthe icon to select the function.

When the Environment setting is None, thesound would be performed as stereo mode(2-channel output). Please select the other settingsfor 6 channels output.

Basic 6 Channel Analog Audio Output Mode Notes:

Appendix- 73 -

English

SPDIF Output Device (Optional Device)

STEP 3:Connect SPDIF to the SPDIF decoder.

Secure the metal bracket of the SPDIF Outputdevice to the chassis back panel with a screw.

Connect the SPDIF device cable to the SPDIF_IOconnector on the motherboard.

A "SPDIF output" device is an optional device. TheSPDIF_IO cable with rear bracket could link to the"SPDIF_IO" connector (As picture.) For the furtherlinkage to decoder, rear bracket provides coaxial cableand Fiber connecting port.

STEP 1:

STEP 2:


Engl

ish

4-2 TroubleshootingBelow is a collection of general asked questions. To check general asked questions based on a specificmotherboard model, please log on to http://www.gigabyte.com.tw

Question 1: I cannot see some options that were included in previous BIOS after updating BIOS. Why?Answer: Some advanced options are hidden in new BIOS version. Please press Ctrl and F1 keys afterentering BIOS menu and you will be able to see these options.

Questions 2: Why is the light of my keyboard/optical mouse still on after computer shuts down?Answer: In some boards, a small amount of electricity is kept on standby after computer shuts downand that's why the light is still on.

Question 3: How do I clear CMOS?Answer: If your board has a Clear CMOS jumper, please refer to the Clear CMOS steps in the manual.If your board doesn't have such jumper, you can take off the on-board battery to leak voltage to clearCMOS. Please refer to the steps below:

Steps:1. Turn off power.2. Disconnect the power cord from MB.3. Take out the battery gently and put it aside for about 1 minute (Or you can use a metal object

to connect the positive and negative pins in the battery holder to makethem short for 5seconds).

4. Re-insert the battery to the battery holder.5. Connect power cord to MB again and turn on power.6. Press Del to enter BIOS and load Fail-Safe Defaults(or load Optimized Defaults).7. Save changes and reboot the system.

Question 4: Why do I still get a weak sound after turning up the speaker to the maximum volume?Answer: Please make sure the speaker you are using is equipped with an internal amplifier. If not,please change another speaker with power/amplifier and try again later.

Question 5: Sometimes I hear different continuous beeps from computer after system boots up. What dothese beeps usually stand for?Answer: The beep codes below may help you identify the possible computer problems. However,they are only for reference purposes. The situations might differ from case to case.

AWARD BIOS Beep Codes1 short: System boots successfully2 short: CMOS setting error1 long 1 short: DRAM or M/B error1 long 2 short: Monitor or display card error1 long 3 short: Keyboard error1 long 9 short: BIOS ROM errorContinuous long beeps: DRAM errorContinuous short beeps: Power error

Appendix- 75 -

English


Engl

ish

Appendix- 77 -

English


Engl

ish

Appendix- 79 -

English

Contact Us

Taiwan (Headquarters)GIGA-BYTE TECHNOLOGY CO., LTD.Address: No.6, Bau Chiang Road, Hsin-Tien,Taipei 231, Taiwan TEL: +886-2-8912-4888 FAX: +886-2-8912-4003Tech. and Non-Tech. Support (Sales/Marketing) :http://ggts.gigabyte.com.twWEB address (English): http://www.gigabyte.com.twWEB address (Chinese): http://www.gigabyte.tw

U.S.A.G.B.T. INC.TEL: +1-626-854-9338FAX: +1-626-854-9339Tech. Support:http://rma.gigabyte-usa.comWeb address: http://www.gigabyte.us

MexicoG.B.T Inc (USA)Tel: +1-626-854-9338 x 215 (Soporte de habla hispano)FAX: +1-626-854-9339Correo: [email protected]. Support:http://rma.gigabyte-usa.comWeb address: http://www.gigabyte-latam.com

JapanNIPPON GIGA-BYTE CORPORATIONWEB address : http://www.gigabyte.co.jp

SingaporeGIGA-BYTE SINGAPORE PTE. LTD.WEB address : http://www.gigabyte.com.sg

ChinaNINGBO G.B.T. TECH. TRADING CO., LTD.WEB address : http://www.gigabyte.cnShanghaiTEL: +86-21-63410999FAX: +86-21-63410100BeijingTEL: +86-10-62102838FAX: +86-10-62102848WuhanTEL: +86-27-87851061FAX: +86-27-87851330GuangZhouTEL: +86-20-87540700FAX: +86-20-87544306 ext. 333ChengduTEL: +86-28-85236930FAX: +86-28-85256822 ext. 814XianTEL: +86-29-85531943FAX: +86-29-85539821ShenyangTEL: +86-24-83992901FAX: +86-24-83992909

IndiaGIGABYTE TECHNOLOGY (INDIA) LIMITEDWEB address : http://www.gigabyte.in

AustraliaGIGABYTE TECHNOLOGY PTY. LTD.WEB address : http://www.gigabyte.com.au


Engl

ish

GermanyG.B.T. TECHNOLOGY TRADING GMBHWEB address : http://www.gigabyte.de

U.K.G.B.T. TECH. CO., LTD.WEB address : http://www.giga-byte.co.uk

The NetherlandsGIGA-BYTE TECHNOLOGY B.V.WEB address : http://www.giga-byte.nl

FranceGIGABYTE TECHNOLOGY FRANCEWEB address : http://www.gigabyte.fr

ItalyWEB address : http://www.giga-byte.it

SpainGIGA-BYTE SPAINWEB address : http://www.giga-byte.es

Czech RepublicRepresentative Office Of GIGA-BYTE Technology Co., Ltd.in CZECH REPUBLICWEB address : http://www.gigabyte.cz

TurkeyRepresentative Office Of GIGA-BYTE Technology Co., Ltd.in TURKEYWEB address : http://www.gigabyte.com.tr

To submit a technical or non-technical (Sales/Marketing) question, please link to :http://ggts.gigabyte.com.twThen select your language to enter the system.

RussiaMoscow Representative Office Of GIGA-BYTE TechnologyCo., Ltd.WEB address : http://www.gigabyte.ru

LatviaGIGA-BYTE LatviaWEB address : http://www.gigabyte.com.lv

PolandOffice of GIGA-BYTE TECHNOLOGY Co., Ltd. in POLANDWEB address : http://www.gigabyte.pl

UkraineWEB address : http://www.gigabyte.kiev.ua

RomaniaRepresentative Office Of GIGA-BYTE Technology Co., Ltd.in RomaniaWEB address : http://www.gigabyte.com.ro

Serbia & MontenegroRepresentative Office Of GIGA-BYTE Technology Co., Ltd.in SERBIA & MONTENEGROWEB address : http://www.gigabyte.co.yu

GIGABYTE Global Service System

Documents

Motherboard Mamual k8vm800m-Rh e