Moonring Multiples with MOONRING MULTISTAK …...MOONRING MULTISTAK TM Install Guide MOONRING MULTISTAK TM Install Guide 8 of 13 102-000023 - IG120318-A.0 Installation: Suspend Rings

A 1035 22nd Avenue, Unit 1 n Oakland, CA 94606 P 510.489.2530 E [email protected] W alwusa.com

INSTALLATION INSTRUCTIONS

MOONRING MULTIPLESMOONRING MULTISTAKTM

STACKED CANOPY

MOONRING MULTISTAKTM Install Guide 2 of 13 102-000023 - IG120318-A.0

MR-MultiStak - Safety & Warnings!1. Read all instructions.2. Install in accordance with national and local electrical code regulations.3. This product is intended to be installed and serviced by a qualified, licensed electrician.4. Only install with a compatible Class 2 LED Driver. This product has not been evaluated for use when

connected to an LED driver that does not comply with Class 2 voltage and energy limited supplies.5. Do not install in wet locations. For dry and damp use only.6. Turn off electrical power before installing or servicing fixture in any way.7. To reduce the risk of fire and overheating, make sure all connections are tight.

1. Lisez toutes les instructions.2. Installez conformément à la réglementation du code électrique national et local.3. Ce produit est destiné à être installé et entretenu par un électricien agréé qualifié.4. Installez uniquement avec un pilote à DEL de classe 2 compatible. Ce produit n’a pas été évalué

pour une utilisation lorsqu’il est connecté à un pilote de LED qui n’est pas conforme aux alimenta-tions de tension et d’énergie limitée de classe 2

5. Ne pas installer à l’extérieur ou dans des endroits humides. Pour une utilisation en intérieur et sec seulement.

6. Coupez l’alimentation électrique avant de évoluer le système d’éclairage en aucune façon.7. Pour réduire le risque d’incendie et de surchauffe, assurez-vous que toutes les connexions sont bien

serrées.

MR-MultiStak - Attention!

SHOCK HAZARD! May result in serious injury or death. Turn power OFF at circuit breaker prior to installation or servicing.

MOONRING MULTISTAKTM Install Guide MOONRING MULTISTAKTM Install Guide 3 of 13 102-000023 - IG120318-A.0

Table of Contents

Luminaire Overview

Included Parts

Parts (by others)

Tools Required

Installation4”x4” Square J-Box

Remote Driver and Drywall

Lens

Wiring Diagrams

Troubleshooting

Diagram

Traditional On/Off

0-10V Dimming

DMX

DALI

Lutron LDE

4

4

4

4

4

6

6

6

10

11

11

11

11

11

11

13

Canopy Installation 7

Suspend Rings 8

Wiring 9

Quick Specs 4

4”x4” Octagonal J-Box 6

Canopy Overview 5

0-10V Tunable 12


Included Parts

7"15∕8"

Luminaire Overview

8X #10 screws (for structure)

Wire nuts

Parts (by others)Screwdriver

Drill

Philips bit

Tools Required

Wire strippers

MR Fixtures MR Lenses MultiStakCeiling Suspension Plate

Cover Plate

Input Voltage / Frequency:See product label

Rated Current:See engineering drawing

Ambient Temperature:-4° – 120°F (-20° – 50°C)

Environment:Dry and damp locations

Quick Specs

Hardware


mounting screws (by others)

Canopy Overview


4"4"

4"

4"

2A Mount JBOX

55∕8"

4"

31∕2"

1/4” gap between main structure members and J-Box

4"31∕2"

Install drywall with circular, 5 5/8” diameter cutout around J-box.

4 Install drywall

1B Install blocking for structure and JBOX

2B

Installation: 4x4 Square Junction Box

Mount JBOX

1A Install blocking for structure and JBOX

Installation: 4x4 Octagonal Junction Box

Install remote driver J-Box(es) in an accessible/serviceable location. Run low voltage wire from Remote Driver J-Box to Canopy J-Box in accordance with local/state/federal regulations.

3 Install Remote Driver J-Box

Installation: Remote Driver and Drywall

Install blocking to frame J-box in a 4” x 4” square. Install blocking to frame J-box in a 3 1/2” x 4” rectangle.

MOONRING MULTISTAKTM Install Guide 7 of 13 102-000023 - IG120318-A.0MOONRING MULTISTAKTM Install Guide

6 Fasten suspension plate to structure

Ensure screws properly penetrate blocking for proper load bearing.

7 Fasten suspension plate to structure

Installation: Canopy Installation

5 Attach suspension plate to J-Box 8 Install MOONRING MULTISTAKTM

Attach canopy suspension plate to J-Box on ceiling. Suspension plate must sit flush on ceiling surface.

Fasten canopy suspension plate to structure using 8X #10 screws (min. 2” length).

Install MOONRING MULTISTAK to canopy suspension plate using provided 1/4”-20 screws.


Installation: Suspend Rings

10 Insert suspension cable and adjust

With rings suspended at proper height, cut excess suspen-sion cable.

13 Trim excess suspension cable

9 Raise 1st fixture to cables 12 Raise 3rd firxture to cables

11 Raise 2nd fixture to cables

Raise first fixture to corresponding cables. See submittal drawing to match correct cables to cable grippers.

Insert suspension cable into cable gripper and adjust length as necessary.

Raise second fixture to corresponding cables. See submittal drawing to match correct cables to cable grippers. Insert cable into cable grippers as shown in step 10.

Raise third fixture to corresponding cables. See submittal drawing to match correct cables to cable grippers. Insert cable into cable grippers as shown in step 10.


Installation: Wiring

15 Install cover plate

14 Make wiring connectionsBring cables from rings through cover plate. Pull wire to desired length and tie knot above plate. Ensure adequate cable length to reach canopy (lift canopy cover plate to verify). If cable is too long, re-tie knot. Once cable length is correct, trim cable and make wiring connections using wire nuts. See submittal drawings and diagrams on pg. 11 for complete wiring instruction.

Push wiring connections into J-Box and canopy. Lift cover plate to stack and secure using provided 10-32 screw.


Installation: Lens

Ensure lenses overlap, as shown.

16B Install Downlight Lenses

Carefully angle/snap lenses into fixture, as shown. Note: because lenses are not adhered to fixture, fixture may only be mounted at moderate angles up to 20 degrees.

16A Install Downlight Lenses

Turn breaker ON and ensure that fixture operates as intended and that there are no loose connections.

17 Turn Power On

MOONRING MULTISTAKTM Install Guide 11 of 13 102-000023 - IG120318-A.0

Wiring Diagrams

BrownBlue

Driver 1 LED +

Driver 1 LED -

YellowOrange

Driver 2 LED +

Driver 2 LED -

DC

BlackWhite GreenGround

Line Voltage (Hot)

Line Voltage (Neutral)

L

NAC 50/60Hz

Traditional On/Off

Remote LED Driver J-Box

BrownBlue

Driver 1 LED +

Driver 1 LED -

YellowOrange

Driver 2 LED +

Driver 2 LED -

DC

BlackWhite Green

GreyPurple

Line Voltage (Hot)


Ground

0-10VDC (Dim-)

0-10VDC (Dim+)

L

NAC 50/60Hz

DIM-

DIM+

0-10V Dimming


BrownBlue

Driver 1 LED +

Driver 1 LED -

YellowOrange

Driver 2 LED +

Driver 2 LED -

DC

BlackWhite Green

ClearBlack

DMX in shield

DMX in -

Line Voltage (Hot)


Ground

L

NAC 50/60Hz

DMX In Shield

DMX in -

RedDMX in +DMX in +

ClearBlack

DMX out shield

DMX out -

WhiteDMX out +

DMX Out Shield

DMX out -

DMX out +

DMX

Remote LED Driver/Decoder

J-Box

BrownBlue

Driver 1 LED +

Driver 1 LED -

YellowOrange

Driver 2 LED +

Driver 2 LED -

DCBlackWhite Green

PurpleGrey

Line Voltage (Hot)


Ground

Data +

Data -

L

NAC 50/60Hz

DATA +

DATA -

DALI


J-Box

BrownBlue

Driver 1 LED +

Driver 1 LED -

YellowOrange

Driver 2 LED +

Driver 2 LED -

DC

BlackWhite Green

PurpleGrey

Line Voltage (Hot)


Ground

E1

E2

L

NAC 50/60Hz

E1

E2

Lutron LDE



Wiring Diagrams

BrownBlue

Driver 1 LED +

Driver 1 LED -

YellowOrange

Driver 2 LED +

Driver 2 LED -

DCBlackWhite Green

GreyPurple

Line Voltage (Hot)


Ground

0-10VDC (Dim-)

0-10VDC (Dim+)

L

NAC 50/60Hz

DIM-

DIM+

YellowBrown

0-10VDC (Tune-)

0-10VDC (Tune+)

TUNE-

TUNE+

0-10V Tunable


J-Box


Troubleshooting

Only a certified electrician can service and troubleshoot product field issues. Always turn main power off before servicing fixture.

Full Fixture does not illuminate • Ensure fixture is wired correctly and power is on. • Check that circuit breaker is on and not off or tripped.• Internal LED driver may be defective. • Ensure no wires are pinched between parts after joining sections or

re-attaching end caps.

Full fixture is flickering • 0-10V, DMX, and DALI Dimming Models: Ensure polarity is correct for DATA + and - connections. Swapping DATA + and - connections can cause flickering.

• TRIAC Dimming Models: Ensure a compatible TRIAC Forward Phase dimmer is connected to fixture. Call tech support for further informa-tion.

• Possible loose DATA + and - connections from fixture to 0-10V, DMX, or DALI control.

• Possible loose low voltage DC + or - connection from driver to LED. Call customer support.

Fixture section(s) do not illuminate

Fixture section(s) are flickering

Fixture does not dim

• Possible loose low voltage DC + or - connection between LED boards or from LED driver to LED boards.

• Some fixtures contain multiple LED drivers. In this case, it’s possible one of the drivers is defective, which will cause the LED connected to the driver not to illuminate. Call tech support.

• Ensure no wires are pinched between parts after joining sections or re-attaching end caps.

• Possible loose low voltage DC + or - connection between LED boards.

• 0-10V, DMX, and DALI Dimming Models: Ensure polarity is correct for DATA + and - connections. Swapping DATA + and - connections can cause flickering.

• TRIAC Dimming Models: Ensure a compatible TRIAC Forward Phase dimmer is connected to fixture. Call tech support for further infor-mation.

• Possible loose DATA + and - connections from fixture to 0-10V, DMX, or DALI control.

Documents

Moonring Multiples with MOONRING MULTISTAK …...MOONRING MULTISTAK TM Install Guide MOONRING MULTISTAK TM Install Guide 8 of 13 102-000023 - IG120318-A.0 Installation: Suspend Rings