43
Module 2: General Working Conditions 2.2 Working Surfaces Susan Harwood Grant Number SH-17820-08-

Module 2: General Working Conditions 2.2 Working Surfaces

Embed Size (px)

DESCRIPTION

Module 2: General Working Conditions 2.2 Working Surfaces Susan Harwood Grant Number SH-17820-08-60-F-23. - PowerPoint PPT Presentation

Citation preview

Page 1: Module 2:  General Working Conditions 2.2 Working Surfaces

Module 2: General Working Conditions

2.2 Working SurfacesSusan Harwood Grant Number SH-17820-

08-60-F-23

Page 2: Module 2:  General Working Conditions 2.2 Working Surfaces

This material was produced under grant number SH-17820-08-60-F-23 from the Occupational Safety and Health Administration, U.S. Department of Labor. It does not necessarily reflect the views or polices of the U.S. Department of Labor, nor does mention of trade names, commercial products, or organizations imply endorsement by the U.S. Government.

2

Page 3: Module 2:  General Working Conditions 2.2 Working Surfaces

Describe a working surface Show how debris aloft are

potentially hazardous Recognize the effects of

corrosion Identify manholes and

openings3

Page 4: Module 2:  General Working Conditions 2.2 Working Surfaces

4

Page 5: Module 2:  General Working Conditions 2.2 Working Surfaces

5Figure 1 Ship with barges in the slip

Page 6: Module 2:  General Working Conditions 2.2 Working Surfaces

6Figure 2 Close up view of the working surfaces and guards

Page 7: Module 2:  General Working Conditions 2.2 Working Surfaces

7Figure 3 Warning guards in place on exposed decks

Page 8: Module 2:  General Working Conditions 2.2 Working Surfaces

8Figure 4 Multiple decks and severe corrosion

Page 9: Module 2:  General Working Conditions 2.2 Working Surfaces

9Figure 5 Gangway to vessel secured

Page 10: Module 2:  General Working Conditions 2.2 Working Surfaces

10Figure 6 Engine room deck plates in place

Page 11: Module 2:  General Working Conditions 2.2 Working Surfaces

11Figure 7 Cargo boom and rigging

Page 12: Module 2:  General Working Conditions 2.2 Working Surfaces

12Figure 8 Officers quarters

Page 13: Module 2:  General Working Conditions 2.2 Working Surfaces

13Figure 9 Life boat in the hoist position

Page 14: Module 2:  General Working Conditions 2.2 Working Surfaces

14Figure 10 Corrosion along deck and external surfaces

Page 15: Module 2:  General Working Conditions 2.2 Working Surfaces

15Figure 11 Gun turret above main deck

Page 16: Module 2:  General Working Conditions 2.2 Working Surfaces

16Figure 12 Painted decks and gear awaiting to be removed

Page 17: Module 2:  General Working Conditions 2.2 Working Surfaces

17Figure 13 Rust along welds and main deck

Page 18: Module 2:  General Working Conditions 2.2 Working Surfaces

18Figure 14 Uneven surfaces

Page 19: Module 2:  General Working Conditions 2.2 Working Surfaces

19Figure 15 Personnel working along edge of vessel

Page 20: Module 2:  General Working Conditions 2.2 Working Surfaces

20Figure 16 Hull cut out at the stern of vessel

Page 21: Module 2:  General Working Conditions 2.2 Working Surfaces

21Figure 17 Personnel in life jackets working over the side

Page 22: Module 2:  General Working Conditions 2.2 Working Surfaces

22Figure 18 Reduced visibility in the engine room

Page 23: Module 2:  General Working Conditions 2.2 Working Surfaces

23Figure 19 Crews quarters and lockers

Page 24: Module 2:  General Working Conditions 2.2 Working Surfaces

24Figure 20 Personnel utilizing fall protection on scaffolding

Page 25: Module 2:  General Working Conditions 2.2 Working Surfaces

25Figure 21 Mast and ladders

Page 26: Module 2:  General Working Conditions 2.2 Working Surfaces

26Figure 22 Cutting on cargo compartment with limited access

Page 27: Module 2:  General Working Conditions 2.2 Working Surfaces

27

Page 28: Module 2:  General Working Conditions 2.2 Working Surfaces

28Figure 23 Hatch covering removed before section removed

Page 29: Module 2:  General Working Conditions 2.2 Working Surfaces

29Figure 24 Open scuttle on the main hatch door

Page 30: Module 2:  General Working Conditions 2.2 Working Surfaces

30Figure 25 Combing along open hatch

Page 31: Module 2:  General Working Conditions 2.2 Working Surfaces

31Figure 26 Leading edging with warning markers

Page 32: Module 2:  General Working Conditions 2.2 Working Surfaces

32Figure 27 Workers in fall protection

Page 33: Module 2:  General Working Conditions 2.2 Working Surfaces

33Figure 28 Worker cutting above engineered guards

Page 34: Module 2:  General Working Conditions 2.2 Working Surfaces

34Figure 29 Section ready to be hoisted

Page 35: Module 2:  General Working Conditions 2.2 Working Surfaces

35Figure 30 Workers along the engineered barrier

Page 36: Module 2:  General Working Conditions 2.2 Working Surfaces

36Figure 31 Worker in all protection snapped in place

Page 37: Module 2:  General Working Conditions 2.2 Working Surfaces

37Figure 32 Engine room with deck plates in place

Page 38: Module 2:  General Working Conditions 2.2 Working Surfaces

38Figure 33 Ladder with warning tape

Page 39: Module 2:  General Working Conditions 2.2 Working Surfaces

39Figure 34 Decks removed from the deep cargo tanks

Page 40: Module 2:  General Working Conditions 2.2 Working Surfaces

40

Page 41: Module 2:  General Working Conditions 2.2 Working Surfaces

41

Page 42: Module 2:  General Working Conditions 2.2 Working Surfaces

OSHA eTool www.osha.gov The Free Dictionary www.thefreedictionary.com

42

Page 43: Module 2:  General Working Conditions 2.2 Working Surfaces

43

Worker Safety is a Priority