Modularization Concepts of Automotive Front

------------------------------------------------------------------------------------------------------------------------------

IQPC GmbH | Friedrichstr. 94 | D-10117 Berlin, Germany

t: +49 (0) 30 2091 3330 | f: +49 (0) 30 2091 3263 | e: [email protected] | w: www.iqpc.de

Visit IQPC for a portfolio of topic-related events, congresses, seminars and conferences: www.iqpc.de

1

Modularization concepts of automotive front-ends

Front-end modules have been around since the early 1990s, with Volkswagen implementing

them in their VWs and Audis, and they have proved to be a significant improvement over

earlier automobile assembly methods. A number of European manufacturers have adopted

modularization, but it has been slow in coming to North America. Because of higher fuel

costs, there has been a need to reduce weight. In order to see what in an automotive front-

end can be modularized, we should review front-end systems and assemblies, themselves.

What is an automotive front-end?

When you go to a shop and ask the mechanic to check your car’s front end, they place the

car on a lift or jack stands and proceed to inspect the suspension, steering, and alignment.

If you want to have the brakes checked, normally you specifically have to say “brakes”. If

want to have your cooling system checked, you need to say so. Mechanics normally don’t

think of these as “the front-end” but as separate systems.

However, automotive designers consider all of these, and more as part of the “front-end”, or

front-end module (FEM), literally meaning everything in front of the windshield, save for the

power train [1]. That means frame, body parts, and electrical system, as well as the other

well-known systems, such as suspension.

Typical front-end [Courtesy of Auto-Steel Partnership]

------------------------------------------------------------------------------------------------------------------------------




2

Historically and for conceptual purposes, we think of systems that respond to a function. For

front ends, we consider:

• Brakes

• Steering

• Electrical

• Cooling

• Frame

• Suspension

• Mobility - Wheels, axles, and bearings

Let’s identify the main systems found in the typical automotive front-end. At such point, we

can discuss modularization.

Basic construction of automotive front-end

An automotive front-end consists of suspension steering, part of the braking system,

wheel/bearing assembly, electrical, cooling, air conditioning, and frame. Overlaid onto these

are accessory items and systems, such as V belts, fans, tensioners, and the window washer

system (wipers, pump, and reservoir). We present a brief overview of these systems and

their weight considerations in order to assess what can be modularized and made less

heavy.

Suspension

Any part that is involved in holding the car body up and easing its up and down or sidewise

motion is referred to as suspension. Depending upon the type of suspension, there are

springs - usually coil or air, motor mounts, ball joints (upper and lower), stabilizer bar,

bushings, knuckle, infrastructure (such as yokes and housings), McPherson struts or shock

absorbers, torsion bars, and control arms. This is one of the heaviest systems in the front

end and a candidate for design with lightweight materials.

------------------------------------------------------------------------------------------------------------------------------




3

Basic front end suspension [2]

Steering

The steering system is everything in between the steering wheel to the wheel being turned.

Depending upon the system, this includes the steering wheel, of course, power assist

mechanism (if any), Pitman arm, standard, rack and pinion, and linkage (tie rod ends, tie

rods, idler arm, etc.).

There are two major areas: linkage and steering mechanism. Arrangements will vary, but

most linkage systems consist of ball-type joints (tie rod ends, control arms), intermediate

links (Pitman arm – also called “steering arm”, drag link), threaded adjuster sleeves, and

links.

Major parts of a typical front end linkage system [3]

------------------------------------------------------------------------------------------------------------------------------




4

There are two basic steering assemblies: recirculating ball bearings, and rack and pinion.

The recirculating ball bearing system contains an “endless belt” of ball bearings that serve to

reduce friction between the steering wheel shaft and the main linkage – through the Pitman

arm - to the linkage assembly and then to the wheels. Rack and pinion consists of a gear

rolling against a toothed rack which goes back and forth, in turn, directing the wheels. A

part of most modern steering systems is the power assist unit system, either hydraulic or

electrical. The hydraulic one is made up of a pump, and hydraulic unit attached directly to

the steering gear box, or gear, at the end of the steering column or attached to the rack and

pinion assembly. Active front steering (AFS), technology designed to make the front wheels

turn a certain number of degrees in accordance with the speed of the vehicle, is more

involved and, of course adds more weight.

The typical motor and electromagnetic locking units looks like:

and the AFS actuator:

Assisted front steering system [4]

------------------------------------------------------------------------------------------------------------------------------




5

Brakes

We are talking about 60% of the braking power being done by this half of a system located

in the front-end. This system includes the master cylinder with booster, lines, calipers, shoes

with pads, and rotors (or drums in older cars). For an automatic braking system (ABS), we

add an electric motor and planetary gear set, which are not light components. Rotors and

drums – made of dense steel - can be considered candidates for weight reduction.

Mobility

“Mobility” consists of the parts that allow the car to actually roll on the ground. Although this

is not a standard term in automotive textbooks, such as Stockel [5], it, nevertheless can be

identified as a separate system and with one specific purpose – to allow the vehicle rolling

movement. Constant velocity (CV) joints, axles and axle tube, wheels and wheel bearings,

spindle, and hub are included in the mobility part of the front-end. Overall, the mobility

system is just as heavy as the suspension or steering systems. CV joints replace what was

before the universal joint (UJ), the difference being that the CV joint, as the name indicates,

permits the drive shaft to turn at a constant rotational speed, while the UJ has a varied

angular velocity. Variations of the CV include Rzeppa and tripod joints, double cardan, and

Thompson couplings. Wheels on which the tire is mounted and, in turn, are mounted on the

axle (drive axle for front wheel drive, and driven axle for rear wheel drive cars) are, with the

axle, itself sources of medium weight. The spindle, which some consider part of the

suspension [6] is what the brake rotor or hub mounts. The wheel, hub and its bearings, and

spindle is often called the “wheel-hub assembly”, and the hub, being solid steel, is quite

dense, hence quite heavy. In the CV joint, the spindle is a part of the assembly. In older

models, the spindle is a separate part mounted between the upper and lower control arms.

------------------------------------------------------------------------------------------------------------------------------




6

or

Old-style spindle Spindle as a part of the CV assembly

[7]

Electrical

The wiring harness, computer modules, such as for the engine, brakes, and steering, fuse

box, lights, and battery are part of the front end. The alternator (with its internal regulator)

and starter usually are mounted on the petroleum-fueled engine. For electric cars,

configurations vary, and what is considered as a part of the front-end should be considered

on a case-by-case basis. With electric cars, only the batteries as the main part normally are

in the back of the vehicle.

Cooling

The cooling system has a radiator, water pump, fans – direct mount and separate (usually

electric), low pressure reservoir, thermostat for the fan, and hoses, but usually, only the

radiator, external fan, reservoir, and hoses would be considered as part of the front end,

since the water pump and internal thermostat normally are part of the engine. In electric

vehicles, only the fan is needed.

Air conditioning

This system comprises the compressor (quite heavy), condenser, drier, tubing, hoses, ducts,

and squirrel cage fans. Usually, this system is scattered throughout the front-end, condenser

being in front, drier on one side and the compressor on the other. The blowers are attached

------------------------------------------------------------------------------------------------------------------------------




7

to the fire wall, pointing inward to the inside compartment.

Frame

The frame includes support members (I-beam, or sheet metal fabricated with a built-in

geometry as a support structure), sheet metal or plastic, fenders, bumper, attachment point

and hardware for attaching, glass, and doors. A central focus of applying new materials has

been on the frame.

References(Subject is indicated by URL – accessed 22 August 2011)

[1] A Survey of Front-End Modularity, http://www.just-auto.com/analysis/review-of-front-end-

modules_id104743.aspx

[2] http://мбмастер.рф/SsangYongRexton/files/2C.pdf [3] http://autorepair.about.com/library/bl244lib.htm

[4] Willy Klier, Gerd Reimann and Wolfgang Reinelt, Concept and Functionality of the Active Front

Steering System, ZF Lenksysteme GmbH, Schwäbisch Gmünd, Germany, No. 2004-21-0073, 2003 SAE

International (2003), pp. 1-3

[5] http://www.goodreads.com/author/show/617260.Martin_T_Stockel

[6] http://en.wikipedia.org/wiki/Spindle_%28automobile%29

http://www.secondchancegarage.com/public/140.cfm

http://www.paulstravelpictures.com/GM-Wheel-Bearing-Hub-Assembly-Replacement/index.html and

http://www.getusedparts.com/auto_parts_guide/S/used_spindle.html

[7] Potentials and Limitations of Pre-Crash Systems for Pedestrian Protection

Resources (Subject is indicated by URL – accessed 22 August 2011)

http://en.wikipedia.org/wiki/Caster_angle

http://www.automotive-frontend.com/Event.aspx?id=578242

http://www.broadwaytrans.com/resources/car-care-articles/brakes - smaller sized brake system

http://www.stjoesauto.com/course_support/Unit%201%20Introduction%20to%20Brakes.PDF

http://www.stjoesauto.com/course_support/

http://www.iqpc.com/Event.aspx?id=578750

http://www.a-sp.org/database/publicationmain.asp

http://en.wikipedia.org/wiki/Constant-velocity_joint

Want to learn more about current technologies and developments in automotive front-end?

Visit our download centre for more articles, whitepapers and interviews:

http://bit.ly/oRF4ay

------------------------------------------------------------------------------------------------------------------------------




8

http://wardsautoworld.com/ar/auto_frontend_module_demand_2/

http://www.faurecia.com/expertise-innovation/automotive-equipment/Pages/car-exterior.aspx

http://wardsauto.com/ar/module_supplier_future_100907/

About IQPC:

IQPC provides tailored conferences, large events, seminars and internal training programmes for

managers around the world. Topics include current information on industry trends, technical

developments and regulatory rules and guidelines. IQPC's conferences are market leading events,

highly regarded for their opportunity to exchange knowledge and ideas for professionals from various industries.

IQPC has offices in major cities across six continents including: Berlin, Dubai, London, New York, Sao

Paulo, Singapore, Johannesburg, Sydney and Toronto. IQPC leverages a global research base of best

practices to produce an unrivaled portfolio of problem-solving conferences. Each year IQPC offers

approximately 2,000 worldwide conferences, seminars, and related learning programs.

Documents

Modularization Concepts of Automotive Front