SECTION: Z4.10.100ZM2392

0917Supersedes

0117

MODELS 7008 - 7009 - 7010 GRINDER PUMPPRODUCT FEATURES

1.0, 1.5 & 2.0 HP

© Copyright 2017 Zoeller® Co. All rights reserved.

3

11

1

5

4

7

14

13

15

16

9

12

6

10

6

17

2

8

ZEPA0600B

APPLICATIONS• Sanitary Sewage • Housing Developments • Pressure Sewers

SPECIFICATIONSPUMP:• Nonautomatic or automatic with integral on-off switch.• Discharge Size - 1-1/4" NPT vertical.• Mechanical Seal - silicon carbide/carbon, with Buna-N elastomers.• Construction - Cast Iron ASTM A48, Class 30, 30,000# tensile strength.• Corrosionresistantpowdercoatedepoxyfinish.• 440C Stainless Steel cutter and plate hardened to Rockwell C 55-60.• Attaching Hardware and Lifting Handle - 304 stainless steel.• Square Ring Seal and gasket - Viton.• Impeller-Engineered,glass-filledplasticwithSSinsertandtoppumpoutvanes.• Power Cable Length - 20'

OPTIONAL: Additional cord length ___ ft. Pre-packaged Basin Systems Silicon Carbide/Silicon Carbide Seal Rail Systems Bronze Impeller

MOTOR:• 1.0, 1.5 & 2.0 HP, 3450 RPM.• Capacitor Start/Run 1 phase motor with internal starting circuit and overload protection. 115 Volt: 1.0 HP 200 & 230 Volt: 1.0, 1.5 & 2.0 HP• 3 Phase induction motor - 200/230/460/575 Volt• 416 Stainless Steel Motor shaft.• Stator - Class B insulation and lead wires. Nema B design.• Integral thermal overload, single phase units• Housing-CastIron,oil-filled,withcoolingfins.• Upper & Lower Ball Bearings - Dual high carbon chromium steel.

DIMENSIONS: Height: 18-5/8" Major Width: 11-5/8" Weight: 88 lbs.

FEATURESEASY INSTALLATION: Pump is normally supplied with twenty feet of multi conductor, power cable (1) as standard, in either an automatic unit furnished with an integral on/off control or nonautomatic type. Alternate cable lengths are available. Units have 3 legs (2) as an integral part of pump housing for free standing requirements. Pump and motor assembly can be easily lowered into position, without disturbing the piping, by use of a rail system. Pump is furnished with a stainless steel lifting handle (3).Long lasting internal components - Class B insulation system (4) rated for 104°F (40°C) max. liquids. Thermal protection (5) standard on single phase motors. Conservatively rated antifriction upper and lower ball bearings (6) for

radial and thrust loads. Finned, oil filled motor housing (7) for greater heatdissipation, and cooler running motors. Cutter and plate (8) can be resharpened to extend pump life. Both are made of 440C stainless steel and hardened to a value of 55-60 on a Rockwell C scale. Capacitor Start/Capacitor Run single phase motor (9) provides extra start and run torque for cutting.Complete environmental protection - Viton square ring (10) and gasket, and heavy duty cord connectors (11) keep liquid from entering the motor assembly. MotorhousingisconstructedoffinnedpowdercoatedepoxyClass30castiron(12). Hardware (13) is stainless steel. The silicon carbide/carbon shaft seal (14) provides exceptional motor protection. Seal has stainless steel and Buna-N components. Vent hole helps prevent air locking. Engineered plastic vortex impeller (15) with top pump out vanes for seal protection is keyed and bolted to the shaft. The pump housing (16) has a concentric design thereby equalizing the pressure forces inside the housing, which will extend the service life of the seal and bearings. All pumps come with 1-1/4" NPT female vertical discharge (17).

R

(Tested to UL778 andCSA22.2 108 Standards)

MAIL TO: P.O. BOX 16347 • Louisville, KY 40256-0347SHIP TO: 3649 Cane Run Road • Louisville, KY 40211-1961

(502) 778-2731 • 1 (800) 928-PUMP • FAX (502) 774-3624

visit our web site:zoellerengineered.com

Product information presented here reflects conditions at time of publication. Consult factory regarding discrepancies or inconsistencies.

© Copyright 2017 Zoeller® Co. All rights reserved.

Zoeller® Engineered Products • 3649 Cane Run Road • Louisville, Kentucky 40211-1961 • (502) 778-2731

SWPA Data Categories Presented -- Data on this sheet supply design information as the minimum recommended by the Submersible Wastewater Pump Association and is defined in accordance with SWPA’s Standardized Definitions for Pump and Motor Characteristics. The accuracy of the data is the responsibility of Zoeller Engineered Products.

RESERVE POWERED DESIGN For unusual conditions a reserve safety factor is engineered into the design of every Zoeller® pump.

MODELS 7008-7009-7010 TECHNICAL DATA

2 HP - Single Seal

MODEL HP SERVICEFACTOR

115V / 1 PH 200V / 1 PH 230V / 1 PH 200V / 3 PH 230V / 3 PH 460V / 3 PH 575V / 3 PH

FLA LRA FLA LRA FLA LRA FLA LRA FLA LRA FLA LRA FLA LRA

7008 1.0 1.2 13.6 46.0 7.7 27.7 8.5 57.0 7.5 47.4 6.9 44.4 3.7 21.6 2.7 17.57009 1.5 1.2 -- -- 12.0 61.6 10.8 57.0 9.2 47.4 8.2 44.4 4.2 21.6 3.2 17.57010 2.0 1.2 -- -- 15.5 61.6 13.7 57.0 11.0 47.4 9.9 44.4 5.0 21.6 3.9 17.5

SHAFT SEAL CONSTRUCTION:STANDARD CARBON/SILICON CARBIDEOPTIONAL SILICON CARBIDE/SILICON CARBIDE

MOTOR PROTECTION INTEGRAL ON-LEAD (1 PH); CONTROL PANEL (3 PH)IMPELLER MATERIAL STANDARD ENGINEERED PLASTIC OPTIONAL BRONZEMAXIMUM WATER TEMPERATURE: 104°F (40°C)

IMPELLER TYPE: VORTEX, ENGINEERED PLASTIC MECHANICAL SHAFT SEAL: TYPE 6ACUTTER & PLATE: 420C SS HARDENED TO ROCKWELL C55-60 MOTOR DESIGN LETTER: NEMA B (3 Ph) NEMA L (1Ph)PUMP NET WEIGHT: 88 lbs. (39.9 kg) POWER CORD LENGTH: ft (m)

(20' STANDARD) OPTIONAL: 25' 35' 50'(7.6 m) (10.7 m) (15.2 m)O-RING & GASKET: VITON

MOTOR SHAFT: 416 SS POWER CORD: 14 GAUGE SOWRPM: 3450 STATOR & LEAD WIRES INSULATION: CLASS BMOTOR TYPE: SUBMERSIBLE MAXIMUM STATOR TEMPERATURE: 266 °F (130 °C)

MODELS: 7008 7009 7010PUMP NAME PLATE HORSEPOWER: 1.0 1.5 2.0SERVICE FACTOR: 1.2 1.2 1.2MAXIMUM KW INPUT: 2.1 2.3 3.4STANDARD IMPELLER DIAMETER: 4.25" 5.125" 5.825"DISCHARGE SIZE: 1.25" NPT 1.25" NPT 1.25" NPT