Model PG9MAB MULTIPOISE CONDENSING GAS FURNACE · Model PG9MAB MULTIPOISE CONDENSING GAS FURNACE FEATURES INSTALLATION The 4-way multipoise design allows ... exchanger is positioned

SS-PG9MAB-01

MU

LTIP

OIS

E C

ON

DE

NS

ING

GA

S F

UR

NA

CE

Mod

el P

G9M

AB

FEATURES

INSTALLATION

The 4-way multipoise design allows

FLEXIBILITY:

a model PG9MAB to be installedin an upflow, downflow, or horizon-tal orientation. All sizes of thePG9MAB may be installed in directvent (2-pipe) applications. All sizesexcept the 140 size may beinstalled in non-direct vent (1-pipe)applications. The 140 size alsohas an elevation limitation of 7,000ft. See “Combustion Air and VentPipe” table for more information.

CASING:

The casing also has the requiredopenings for left- or right-sideconnection of gas, electric, drain,and vent connections.

COMBUSTION

Enclosed burner assembly isolates

SYSTEM:

operating noise without the expenseof sound deadening devices.

3-PASS

This design accelerates heat trans-

PRIMARY

fer and extracts heat that conven-

HEAT

tional heat exchangers waste up

EXCHANGERS:

the flue. The primary heat ex-changer is made of aluminizedsteel for corrosion resistance.

FLOW-THROUGH

Each cell is laminated with our pa-

SECONDARY

tented polypropylene for greater

HEAT

corrosion resistance to help extend

EXCHANGERS:

the life of the furnace for years ofdependable performance. The heatexchanger is positioned in the fur-nace to extract additional heat fromthe combustion products regard-less of furnace orientation.

LIMITED

The PG9MAB is backed by a Life-

WARRANTY:

time Warranty on the heat ex-changers in direct vent application(20-year in non-direct vent applica-tions) and a 5-year Warranty on allother parts.

MONOPORT

Produce precise air-to-gas mixture

INSHOT

which gives a clean burn. The large

BURNERS

: monoport

on the inshot or injec-

tion

-

type burners seldom, if ever,needs cleaning.

INTEGRATED

The printed-circuit board has con-

CONTROL

venient terminals which permit

CENTER:

quick-connection of a thermostat, airconditioning control circuits, a humid-ifier, or an air cleaner. The controlhas a built-in status indicator andself-test feature. A self-test featureallows for a complete check of themajor components in about 60 sec-onds. The control also features anadjustable blower off delay.

COMBUSTION

The PG9MAB advanced designallows Schedule 40 PVC,Schedule 40 CPVC pipe and fit-tings,

PVC-DWV, SDR-21 PVC,SDR-26 PVC (not approved inCanada), ABS-DWV, or ABS-F628 Schedule 40 pipe to bringair into the furnace for combus-tion and to be used for ventingcombustion products outside thestructure. The vent pipe can ter-minate through a sidewall orthrough the roof.

CERTIFICATIONS:

The PG9MAB units are CSA (for-merly A.G.A. and C.G.A.) designcertified for use with natural and pro-pane gases, as well as GAMAefficiency rating certified. The fur-nace is factory-shipped for use withnatural gas. A CSA (formerly A.G.A.and C.G.A.) listed gas conversion kitis required to convert furnace for usewith propane gas. The modelPG9MAA meets California Air Qual-ity Management District emissionrequirements.

QUALITY

The quality systems for this product

REGISTRATION:

have been registered by UL toISO 9001 Standards.

AIR ANDVENTILATION:

Time

Roman

—2—

11 ⁄4"

1"

13⁄16

"5 ⁄8

" 5 ⁄16"

1"

39 7 ⁄8

"

11⁄16

"

7 ⁄16"

14 1 ⁄2

"T

YP

17 5 ⁄1

6"24 1 ⁄2

"27 9 ⁄1

6"T

YP

27 5 ⁄8

"29 11

⁄16"

TY

P

30 13

⁄16"32

5 ⁄8"

TY

P

33 1 ⁄4

"T

YP

CO

ND

EN

SAT

ED

RA

IN T

RA

PLO

CAT

ION

(ALT

ER

NAT

EU

PF

LOW

)

7 ⁄8-I

N. D

IAA

CC

ES

SO

RY

PO

WE

R E

NT

RY

7 ⁄8-I

N. D

IAP

OW

ER

CO

NN

CO

ND

EN

SAT

E D

RA

INT

RA

P L

OC

ATIO

N(D

OW

NF

LOW

&H

OR

IZO

NTA

L LE

FT

)

26 15

⁄16"

24 1 ⁄2

"

22 5 ⁄1

6"

2-IN

. CO

MB

US

TIO

N-

AIR

CO

NN

1 ⁄2-I

N. D

IAG

AS

CO

NN

2-IN

. VE

NT

CO

NN

1 ⁄2-I

N. D

IA T

HE

RM

OS

TAT

EN

TR

Y22

11⁄16

"

SID

E IN

LET

23 1 ⁄4

" T

YP

SID

E IN

LET

OU

TLE

T

26 15

⁄16"

28 1 ⁄2

"

22 5 ⁄1

6"

19"

22 1 ⁄4

" T

YP

24 3 ⁄1

6"B

OT

TOM

INLE

T

18 1 ⁄4

"

22 11

⁄16"

2-IN

. CO

MB

US

TIO

N-

AIR

CO

NN 1 ⁄2

-IN

. DIA

GA

S C

ON

N

7 ⁄8-I

N. D

IAP

OW

ER

CO

NN

1 ⁄2-I

N. D

IAT

HE

RM

OS

TAT

EN

TR

Y

2-IN

. VE

NT

CO

NN

DIM

PLE

LO

CAT

OR

SF

OR

HO

RIZ

ON

TAL

HA

NG

ING

SID

E IN

LET

9 7 ⁄1

6"T

YP

26 15

⁄16"

TY

P

CO

ND

EN

SAT

ED

RA

IN L

OC

ATIO

N(U

PF

LOW

)

30 1 ⁄2

"

9 ⁄16"

TY

P

CO

ND

EN

SAT

ED

RA

IN L

OC

ATIO

N(U

PF

LOW

)E

INLE

T

11/16

"11

/16"

D13

/16"

13/16

"

OU

TLE

T

A

AIR

FLO

W26

1 ⁄4"

26 1 ⁄4

"

CO

ND

EN

SAT

E D

RA

INT

RA

P L

OC

ATIO

N(D

OW

NF

LOW

&H

OR

IZO

NTA

L R

IGH

T)

OR

ALT

ER

NAT

E1 ⁄2

-IN

. DIA

GA

S C

ON

N

NO

TES

: M

inim

um r

etur

n-ai

r op

enin

g at

furn

ace,

bas

ed o

n m

etal

duc

t. If

flex

duct

is u

sed,

see

flex

duc

t man

ufac

ture

r's r

ecom

men

datio

n fo

r eq

uiva

lent

dia

met

ers:

1. F

or 8

00 C

FM

16

-in. r

ound

or

14-1

/2 X

12-

in. r

ecta

ngle

. 2

. For

120

0 C

FM

20

-in. r

ound

or

14-1

/2 X

19-

1 /2

in. r

ecta

ngle

. 3

. For

160

0 C

FM

22

-in. r

ound

or

14-1

/2 X

23-

1 /4

in. r

ecta

ngle

. 4

. For

airf

low

req

uire

men

ts a

bove

180

0 C

FM

, see

Air

Del

iver

y T

able

in p

rodu

ct S

peci

ficat

ion

She

et fo

r sp

ecifi

c us

e of

sin

gle

side

inle

ts. T

he u

se o

f bot

h si

de in

lets

, a c

ombi

natio

n of

1 s

ide

and

the

botto

m, o

r th

e bo

ttom

onl

y w

ill e

nsur

e ad

equa

te r

etur

n-ai

r o

peni

ngs

for

airf

low

req

uire

men

ts a

bove

180

0 C

FM

at 0

.5” W

.C. E

SP.

A02

185

DIM

EN

SIO

NS

(In

.)

UN

IT S

IZE

AD

ES

HIP

. WE

IGH

T (

Lb

)

0240

4017

-1/2

15-7

/816

165

0360

4017

-1/2

15-7

/816

166

0240

6017

-1/2

15-7

/816

172

0360

6017

-1/2

15-7

/816

174

0480

6017

-1/2

15-7

/816

174

0360

8017

-1/2

15-7

/816

188

0480

8017

-1/2

15-7

/816

194

0600

8021

19-3

/819

-1/2

206

0481

0021

19-3

/819

-1/2

219

0601

0021

19-3

/819

-1/2

221

0601

2024

-1/2

22-7

/823

250

0601

4024

-1/2

22-7

/823

250

—3—

1⁄2 ODINDUCER HOUSINGDRAIN CONNECTION

1⁄4 ODCOLLECTOR BOX TOTRAP RELIEF PORT

5⁄8 ODCOLLECTOR BOXDRAIN CONNECTION

1⁄2-IN. PVC OR CPVC

SCREW HOLE FORUPFLOW OR DOWN-FLOW APPLICATIONS(OPTIONAL)

1 42

7 8

1 87

SLOT FOR SCREWHORIZONTALAPPLICATION

(OPTIONAL)

WIRE TIEGUIDES(WHEN USED)

1 21

3 41

3 4

FRONT VIEW SIDE VIEW

FURNACEDOOR

FURNACEDOOR CONDENSATE

TRAP

78

1 426

4

FURNACESIDEFURNACE

SIDE

1 21

1 426

43 45 3 45

4

SIDE VIEW FRONT VIEW END VIEW FRONT VIEW

3 4

DOWNFLOW AND ALTERNATEEXTERNAL UPFLOW APPLICATIONS

HORIZONTALAPPLICATIONS

FIELDDRAINCONN

FIELDDRAINCONN

CONDENSATETRAP (INSIDE)

BLOWER SHELF

ALTERNATE DRAINTUBE LOCATION

UPFLOW APPLICATIONS

CONDENSATE TRAPDRAIN TUBE LOCATION

MEETS DOE RESIDENTIAL CONSERVATION SERVICESPROGRAM STANDARDS.

Before purchasing this appliance, read importantenergy cost and efficiency information availablefrom your retailer.

A93026

CONDENSATE TRAP

ama

D E S I G N

C E R T I F I E D ®

As an ENERGY STAR® partner, Payne Heating & Cooling has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.

REGISTERED

ISO 9001:2000

—4—

SPECIFICATIONS

* Gas input ratings are certified for elevations to 2000 ft. For elevations above 2000 ft, reduce ratings 2 percent for each 1000 ft above sea level. In Canada, derate the unit 5 percent from 2000 to 4500 ft above sea level.

† Capacity and AFUE in accordance with U.S. Government DOE test procedures.‡ Airflow shown is for bottom only return-air supply. For air delivery above 1800 CFM, see Air Delivery table for other options. A filter is required for each return-air sup-

ply.** Permissible voltage limits for proper furnace operation.

†† Unit ampacity = 125 percent of full load amps of largest components plus 100 percent full load amps of all other potential operating components (EAC, humidifier, etc.).‡‡ Length shown is measured 1 way along wire path between unit and service panel for maximum 2 percent voltage drop.*** Required for installation on combustible floors when no coil box is used, or when any coil box other than a Payne CD5, CK5 or KCAKC cased coil is used.

††† For direct vent applications only.N/A—Not Applicable. Unit is not allowed in this installation application.ICS—Isolated Combustion System

UNIT SIZE 024040 036040 024060 036060 048060 036080RATINGS AND PERFORMANCE

Input Btuh* 40,000 40,000 60,000 60,000 60,000 80,000Output Capacity BTUH* (ICS) Direct Vent (2-Pipe) Upflow 37,000 37,000 56,000 56,000 56,000 74,000(Shaded capacities are specified Downflow 37,000 37,000 56,000 56,000 56,000 74,000on rating plate) Horizontal 37,000 37,000 56,000 56,000 56,000 74,000

Non-Direct Vent (1-Pipe) Upflow 37,000 37,000 56,000 56,000 56,000 74,000 Downflow 37,000 37,000 56,000 56,000 56,000 74,000 Horizontal 37,000 37,000 56,000 56,000 56,000 74,000

AFUE%† Direct Vent (2-Pipe) Upflow 92.1 92.1 92.1 92.1 92.1 92.1Nonweatherized ICS Downflow 91 91 91 91 91 91

Horizontal 92.1 92.1 92.1 92.1 92.1 92.1Non-Direct Vent (1-Pipe) Upflow 90

Downflow 90 Horizontal 90

Certified Temperature Rise Range °F 30—60 15—45 45—75 30—60 20—50 40—70Certified External Static Pressure Heating 0.10 0.10 0.12 0.12 0.12 0.15

Cooling 0.50 0.50 0.50 0.50 0.50 0.50Airflow CFM‡ Heating 850 1125 885 1065 1320 1190

Cooling 895 1215 900 1200 1545 1245

ELECTRICAL

Unit Volts—Hertz—Phase 115—60—1Operating Voltage Range Min—Max** 104—127Maximum Unit Amps 6.1 7.4 6.1 7.2 9.6 7.7Unit Ampacity†† 8.4 10.0 8.4 9.8 12.8 10.4Minimum Wire Size 14 14 14 14 14 14Maximum Wire Length (Ft)‡‡ 44 37 44 38 29 36Maximum Fuse Size or Ckt Bkr Amps (Time-Delay Type Recommended) 15 15 15 15 15 15Transformer (24v) 40vaExternal Control Heating 12vaPower Available Cooling 21vaAir Conditioning Blower Relay Standard

CONTROLS

Limit Control SPST Heating Blower Control (Off Delay) Selectable 90, 120, 150, or 180Burners (Monoport) 2 2 3 3 3 4Gas Connection Size 1/2-in. NPT

GAS CONTROLS

Gas Valve (Redundant) Manufacturer White-RodgersMinimum Inlet Pressure (In. wc) 4.5 (Natural Gas)Maximum Inlet Pressure (In. wc) 13.6 (Natural Gas)

Ignition Device Hot Surface

BLOWER DATA

Direct-Drive Motor HP (Permanent Split Capacitor) 1/5 1/3 1/5 1/3 1/2 1/3Motor Full Load Amps 4.9 5.8 4.9 5.8 7.9 5.8RPM (Nominal)—Speeds 1075—3 1075—4 1075—3 1075—4Blower Wheel Diameter x Width (In.) 10 X 6 10 X 7 10 X 6 10 X 7 11 X 8 10 X 7Filter Size (In.)—Permanent Washable (1) 16 X 25 X 1 (1) 20 X 25 X 1

FACTORY-AUTHORIZED AND LISTED, DEALER-INSTALLED OPTIONS

Gas Conversion Kit—Natural-to-Propane KGANP4001ALLGas Conversion Kit—Propane-to-Natural KGAPN3301ALL

Twinning Kit N/A KGATW0601HSI N/A

Manufactured (Mobile) Home Kit††† KGAMH0102KITDownflow Base*** KGASB0201ALLVent Termination Kit (Bracket Only for 2 Pipes)††† 2-in.—KGAVT0101BRA 3-in.—KGAVT0201BRAConcentric Vent Termination Kit (Single Exit)††† 2-in.—KGAVT0501CVT 3-in.—KGAVT0601CVTCondensate Freeze Protection Kit KGAHT0101CFPSide Filter Rack (Without Filter)—Upflow ONLY KGAFR0206ALLThermostat—Programmable For Use With Air Conditioner—TSTATPPSAC01Thermostat—Non-Programmable For Use With Air Conditioner—TSTATPPBAC01-BCondensate Neutralizer Kit (obtained thru RCD) P908-0001Door Gasket Kit KGBAC0110DGK

—5—

SPECIFICATIONS Continued

* Gas input ratings are certified for elevations to 2000 ft. For elevations above 2000 ft, reduce ratings 2 percent for each 1000 ft above sea level. In Canada, derate the unit 5 percent from 2000 to 4500 ft above sea level.

† Capacity and AFUE in accordance with U.S. Government DOE test procedures.‡ Airflow shown is for bottom only return-air supply. For air delivery above 1800 CFM, see Air Delivery table for other options. A filter is required for each return-air sup-

ply.** Permissible voltage limits for proper furnace operation.

†† Unit ampacity = 125 percent of full load amps of largest components plus 100 percent full load amps of all other potential operating components (EAC, humidifier, etc.).‡‡ Length shown is measured 1 way along wire path between unit and service panel for maximum 2 percent voltage drop.*** Required for installation on combustible floors when no coil box is used, or when any coil box other than a Payne CD5, CK5 or KCAKC cased coil is used.

††† For direct vent applications only.N/A—Not Applicable. Unit is not allowed in this installation application.ICS—Isolated Combustion System

UNIT SIZE 048080 060080 048100 060100 060120 060140RATINGS AND PERFORMANCE

Input Btuh* 80,000 80,000 100,000 100,000 120,000 138,000Output Capacity BTUH* (ICS) Direct Vent (2-Pipe) Upflow 74,000 74,000 93,000 93,000 112,000 127,000(Shaded capacities are specified Downflow 74,000 74,000 93,000 93,000 112,000 127,000on rating plate) Horizontal 74,000 74,000 93,000 93,000 112,000 127,000

Non-Direct Vent (1-Pipe) Upflow 74,000 74,000 93,000 93,000 112,000 NA Downflow 74,000 74,000 93,000 93,000 112,000 NA Horizontal 74,000 74,000 93,000 93,000 112,000 NA

AFUE%* Direct Vent (2-Pipe) Upflow 92.1 92.1 92.1 92.1 92.1 92.1Nonweatherized ICS Downflow 91 91 91 91 91 90

Horizontal 92.1 92.1 92.1 92.1 92.1 92Non-Direct Vent (1-Pipe) Upflow 90 NA

Downflow 90 NA Horizontal 90 NA

Certified Temperature Rise Range °F 30—60 20—50 45—75 30—60 40—70 50—80Certified External Static Pressure Heating 0.15 0.15 0.20 0.20 0.20 0.20

Cooling 0.50 0.50 0.50 0.50 0.50 0.50 Airflow CFM‡ Heating 1285 1785 1315 1690 1720 1970

Cooling 1525 1925/2035 1570 1930/2130 2000/2130 1990/2045

ELECTRICAL

Unit Volts—Hertz—Phase 115—60—1Operating Voltage Range Min—Max** 104—127Maximum Unit Amps 10.1 14.1 10.2 14.8 14.6 14.6Unit Ampacity†† 13.4 18.4 13.5 19.3 19.1 18.8 Minimum Wire Size 14 12 14 12 12 12Maximum Wire Length (Ft)‡‡ 28 31 27 30 30 30Maximum Fuse Size or Ckt Bkr Amps (Time-Delay Type Recommended) 15 20 15 20 20 20Transformer (24v) 40vaExternal Control Heating 12vaPower Available Cooling 21vaAir Conditioning Blower Relay Standard

CONTROLS

Limit Control SPST Heating Blower Control (Off Delay) Selectable 90, 120, 150, or 180Burners (Monoport) 4 4 5 5 6 6Gas Connection Size 1/2-in. NPT

GAS CONTROLS

Gas Valve (Redundant) Manufacturer White-RodgersMinimum Inlet Pressure (In. wc) 4.5 (Natural Gas)Maximum Inlet Pressure (In. wc) 13.6 (Natural Gas)

Ignition Device Hot Surface

BLOWER DATA

Direct-Drive Motor HP (Permanent Split Capacitor) 1/2 3/4 1/2 3/4 3/4 3/4 Motor Full Load Amps 7.9 11.1 7.9 11.1 11.1 11.1 RPM (Nominal)—Speeds 1075—4Blower Wheel Diameter x Width (In.) 11 X 8 11 X 10 11 X 8 11 X 10 11 X 10 11 X 10Filter Size (In.)—Permanent Washable (1) 20 X 25 X 1 (1) 24 X 25 X 1

FACTORY-AUTHORIZED AND LISTED, DEALER-INSTALLED OPTIONS

Gas Conversion Kit—Natural-to-Propane KGANP4001ALL*Gas Conversion Kit—Propane-to-Natural KGAPN3301ALLTwinning Kit KGATW0601HSI N/AManufactured (Mobile) Home Kit††† KGAMH0102KIT N/ADownflow Base*** KGASB0201ALLVent Termination Kit (Bracket Only for 2 Pipes)††† 2-in.—KGAVT0101BRA 3-in.—KGAVT0201BRAConcentric Vent Termination Kit (Single Exit)††† 2-in.—KGAVT0501CVT 3-in.—KGAVT0601CVTCondensate Freeze Protection Kit KGAHT0101CFPSide Filter Rack (Without Filter)—Upflow ONLY KGAFR0206ALLThermostat—Programmable For Use With Air Conditioner—TSTATPPSAC01Thermostat—Non-Programmable For Use With Air Conditioner—TSTATPPBAC01-BCondensate Neutralizer Kit (obtained thru RCD) P908-0001Door Gasket Kit KGBAC0110DGK

—6—

Maximum Allowable Vent Pipe Length (Ft)

ALTITUDE (FT)UNIT SIZE(BTUH)

DIRECT VENT (2-PIPE) ONLY NON-DIRECT VENT(1-PIPE) ONLY

NUMBER OF 90° ELBOWS

TERMINATIONTYPE

PIPE DIA(IN.)*

PIPE DIA(IN.)*

1 2 3 4 5 6

0 to 2000

40,000 2 Pipe or 2-inConcentric

1 1 5 NA NA NA NA NA1-1/2 1-1/2 70 70 65 60 60 55

2 2 70 70 70 70 70 70


1-1/2 1-1/2 20 15 10 5 NA NA2 2 70 70 70 70 70 70


1-1/2 1-1/2 10 NA NA NA NA NA2 2 55 50 35 30 30 20

2-1/2 2-1/2 70 70 70 70 70 70


2 2 5 NA NA NA NA NA2-1/2 2-1/2 40 30 20 20 10 NA

3 3 70 70 70 70 70 70

120,000 2 Pipe or 3-in.Concentric

2-1/2 one disk 2-1/2 10 NA NA NA NA NA3† NA 45 40 35 30 25 20

3† no disk 3† 70 70 70 70 70 70


2-1/2 one disk NA 5 NA NA NA NA NA3† one disk NA 40 35 30 25 20 153† no disk NA 60 56 52 48 44 404† no disk NA 70 70 70 70 70 70




TERMINATIONTYPE

PIPE DIA(IN.)*

PIPE DIA(IN.)*

1 2 3 4 5 6

2001 to 3000


1-1/2 1-1/2 67 62 57 52 52 472 2 70 70 70 70 70 70


1-1/2 1-1/2 17 12 7 NA NA NA2 2 70 67 66 61 61 61


2 2 49 44 30 25 25 152-1/2 2-1/2 70 70 70 70 70 70


2-1/2 2-1/2 35 26 16 16 6 NA3 3 70 70 70 70 66 61


3 NA 14 9 NA NA NA NANA 3† 63 62 62 61 61 61

3† no disk NA 70 70 63 56 50 434† no disk 4† no disk 70 70 70 70 70 70


3† one disk NA 20 15 10 5 NA NA3† no disk NA 39 35 31 27 23 194† no disk NA 70 70 70 70 70 70




TERMINATIONTYPE

PIPE DIA(IN)*

PIPE DIA(IN.)*

1 2 3 4 5 6

3001 to 4000


1-1/2 1-1/2 64 59 54 49 48 432 2 70 70 70 70 70 70


1-1/2 1-1/2 16 11 6 NA NA NA2 2 68 63 62 57 57 56


2 2 46 41 28 23 22 132-1/2 2-1/2 70 70 70 70 70 70


2-1/2 2-1/2 33 24 15 14 5 NA3 3 70 70 70 66 61 56

120,0002 Pipe or 3-in.

Concentric3† no disk NA 65 58 51 44 38 31

NA 3† 59 59 58 57 57 564† no disk 4† no disk 4† no disk 70 70 70 70 70 70


3† one disk NA 11 6 NA NA NA NA3† no disk NA 30 26 22 18 14 104† no disk NA 70 70 70 70 70 70

See notes at end of table

COMBUSTION-AIR AND VENT PIPING FOR DIRECT VENT (2 PIPE) AND NON-DIRECT VENT (1-PIPE) APPLICATIONS

—7—

Maximum Allowable Vent Pipe Length (Ft) (Continued)




TERMINATIONTYPE

PIPE DIA(IN.)*

PIPE DIA(IN.)*

1 2 3 4 5 6

4001 to 5000‡


1-1/2 1-1/2 60 55 50 45 44 392 2 70 70 70 70 70 70


1-1/2 1-1/2 15 10 5 NA NA NA2 2 64 59 58 53 52 52


2 2 44 39 26 21 20 112-1/2 2-1/2 70 70 70 70 70 70


2-1/2 2-1/2 31 22 13 12 NA NA3 3 70 70 67 62 57 52


3† no disk NA 53 46 40 33 26 20NA 3† 56 55 54 53 52 52

4† no disk 4† no disk 70 70 70 70 70 70


3† no disk NA 21 17 13 9 5 NA4† no disk NA 69 64 59 54 49 44




TERMINATIONTYPE

PIPE DIA(IN.)*

PIPE DIA(IN.)*

1 2 3 4 5 6

5001 to 6000‡


1-1/2 1-1/2 57 52 47 42 40 352 2 70 70 70 70 70 70


1-1/2 1-1/2 14 9 NA NA NA NA2 2 60 55 54 49 48 47


2 2 41 36 23 18 17 82-1/2 2-1/2 70 70 70 70 70 70


2-1/2 2-1/2 29 21 12 11 NA NA3 3 70 67 62 57 52 47


3† no disk NA 42 35 29 22 15 9NA 3† 53 52 50 49 48 47

4† no disk 4† no disk 70 70 70 70 70 70


3† no disk NA 12 8 NA NA NA NA4† no disk NA 42 37 32 27 22 17




TERMINATIONTYPE

PIPE DIA(IN)*

PIPE DIA(IN)*

1 2 3 4 5 6

6001 to 7000‡


1-1/2 1-1/2 53 48 43 38 37 322 2 70 70 68 67 66 64


1-1/2 1-1/2 13 8 NA NA NA NA2 2 57 52 50 45 44 43


2 2 38 33 21 16 15 62-1/2 2-1/2 70 70 68 67 66 64


2-1/2 2-1/2 27 19 10 9 NA NA3 3 68 63 58 53 48 43


3† no disk NA 31 24 18 11 NA NANA 3† 49 48 47 45 44 43

4† no disk 4† no disk 70 70 70 70 67 62

140,000 2 Pipe or 3-in.Concentric 4† no disk NA 17 12 7 NA NA NA

See notes at end of table


—8—

Maximum Allowable Vent Pipe Length (Ft) (Continued)




TERMINATIONTYPE

PIPE DIA(IN.)*

PIPE DIA(IN.)*

1 2 3 4 5 6

7001 to 8000‡


1-1/2 1-1/2 49 44 39 34 33 282 2 66 65 63 62 60 59


1-1/2 1-1/2 12 7 NA NA NA NA2 2 53 48 46 41 40 38


2 2 36 31 19 14 12 NA2-1/2 2-1/2 66 65 63 62 60 59


2-1/2 2-1/2 25 17 8 7 NA NA3 3 63 58 53 48 43 38


3† no disk NA 20 13 7 NA NA NANA 3† 46 44 43 41 40 38

4† no disk 4† no disk 61 56 51 46 41 36140,000 NA




TERMINATIONTYPE

PIPE DIA(IN.)*

PIPE DIA(IN.)*

1 2 3 4 5 6

8001 to 9000‡


1-1/2 1-1/2 46 41 36 31 29 242 2 62 60 58 56 55 53


1-1/2 1-1/2 11 6 NA NA NA NA2 2 49 44 42 37 35 34


2 2 33 28 17 12 10 NA2-1/2 2-1/2 62 60 58 56 55 53


2-1/2 2-1/2 23 15 7 5 NA NA3 3 59 54 49 44 39 34


3† no disk NA 10 NA NA NA NA NANA 3† 43 41 39 37 35 34

4† no disk 4† no disk 35 30 25 20 15 10140,000 NA




TERMINATIONTYPE

PIPE DIA(IN.)*

PIPE DIA(IN.)*

1 2 3 4 5 6

9001 to 10,000‡


1-1/2 1-1/2 42 37 32 27 25 202 2 57 55 53 51 49 47

60,000 2 Pipe or 2-inConcentric 2 2 45 40 38 33 31 29


2 2 30 25 14 9 7 NA2-1/2 2-1/2 57 55 53 51 49 47


2-1/2 2-1/2 21 13 5 NA NA NA3 3 54 49 44 39 34 29


NA 3† 39 37 35 33 31 294† no disk 4† no disk 10 5 NA NA NA NA

140,000 NA

*Disk usage-Unless otherwise specified, use perforated disk assembly (factory-supplied in loose parts bag). If one disk is stated, separate 2 halves of perforated diskassembly and use shouldered disk half. When using shouldered disk half, install screen side toward inlet box.†Long sweep bend elbow.‡Vent sizing for Canadian installations over 4500 ft (1370 m) above sea level are subject to acceptance by the local authorities having jurisdiction.NA-Not Allowed; pressure switch will not make.NOTES:1. Do not use pipe size greater than those specified in table or incomplete combustion, flame disturbance, or flame sense lockout may occur.2. Size both the combustion-air and vent pipe independently, then use the larger diameter for both pipes.3. Assume two 45° elbows equal one 90° elbow. Long radius elbows are desirable and may be required in some cases.4. Elbows and pipe sections within the furnace casing and at the vent termination should not be included in vent length or elbow count.5. The minimum pipe length is 5 ft for all applications.6. Use 3-in. diameter vent termination kit for installations requiring 4-in diameter pipe.


—9—

COMBUSTION-AIR PIPE FOR NON-DIRECT VENT (1-PIPE) APPLICATIONS(Sizes 040 through 120 only)

FIELD-SUPPLIED2-IN. DIAMETERPVC PIPE

FIELD-SUPPLIED2-IN. DIAMETERPVC 90° ELBOW

COMBUSTION-AIR DISC(FACTORY-SUPPLIED INLOOSE PARTS BAG)

A

A96211

LENGTH OF STRAIGHT PIPE PORTION OFCOMBUSTION-AIR INLET PIPE ASSEMBLY (IN.)

CASING WIDTH A

17-1/2 8-1/2 ± 1/221 10-1/2 ± 1/2

24-1/2 12 ± 1/2

ACCESSORIES

CONCENTRIC VENT FOR DIRECT-VENT (2-PIPE) APPLICATION (ALL MODEL SIZES)

A97110

DIMENSIONS (In.)

* Dimension A will change accordingly as dimension D is lengthened or shortened.† Dimension D may be lengthened to 60 in. maximum. Dimension D may also be shortened by cutting

the pipes provided in the kit to 12 in. minimum.

PART NO. A* B C D† E F

KGAVT0501CVT 33-3/8 2 3-1/2 16-5/8 6-1/4 5-3/4

KGAVT0601CVT 38-7/8 3 4-1/2 21-1/8 7-3/8 6-1/2

C IN. DIA

B IN. DIA PVCVENT/EXHAUST

13/16

B IN. DIA PVCINTAKE/COMBUSTION AIR

D

E

F

A

11/2

Note: See furnace Installation Instructions when venting multiple furnaces near each other.

—10—

17 1⁄8″14 1⁄2″

OPENING

16 1⁄8″23 1⁄8″

OPENING

1 1⁄4″

2 3⁄8″

3⁄4″

1⁄2″

25 1⁄8″

1 1⁄4″ (TYP)

3⁄8″TABS

LOCATINGTAB

LOCATINGTAB

1 2 3 4

4 3 2 1

B

D

ACCESSORIES

(Continued)

ACCESSORY DOWNFLOW SUBBASE

A88207

Disassembled

A97427

Assembled

* The plenum should be constructed 1/4-in. smaller in width and depth than the plenum dimensions shown above.

FURNACECASINGWIDTH

PLENUM OPENING* FLOOR OPENING HOLE NO.FOR WIDTH

ADJUSTMENTFURNACE IN DOWNFLOW APPLICATION A B C D

17-1/2Furnace with or without Cased Coil

Assembly or Coil Box 15-1/8 19 16-3/4 20-3/8 3

21Furnace with or without Cased Coil


24-1/2Furnace with or without Cased Coil


��

C

A

1 1/4″ TYP

PLENUMOPENING

FACTORY-SUPPLIEDFIELD-INSTALLED

INSULATION

SIDE FILTER RACK*

A80199

*Accepts one 16 x 25 x 1 in. filter.

—11—

CLEARANCE TO COMBUSTIBLES

—12—

AIR DELIVERY—CFM (With Filter)*

* A filter is required for each return-air supply.* For horizontal and downflow applications, use “1 side or bottom” or “bottom only” as airflow reference.

UNIT SIZERETURN-AIR

SUPPLY SPEEDEXTERNAL STATIC PRESSURE (In. wc)

0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8

0240401 side

orbottom

HighMed-Low

Low

1075850740

1040825700

995780650

945740620

895685565

840635515

760560455

670480385

0360401 side

orbottom

HighMed-HighMed-Low

Low

147013151125930

141512801110925

140012351085910

128511801045850

12151115990830

11201035915770

995930830705

890825740635

0240601 side

orbottom

HighMed-Low

Low

1100890745

1065865710

1005810670

945765625

900705565

805620505

730540425

610475360

0360601 side

orbottom

HighMed-HighMed-Low

Low

143012701070915

137512601055895

132512151045885

127511601015865

12001105975840

11351035920800

1040950850720

935850750650

0480601 side

orbottom

HighMed-HighMed-Low

Low

1700150013251205

1695146512951170

1640143512651145

1580138512301110

1545135511901080

1450130011501035

138012501105990

131011851050950

0360801 side

orbottom

HighMed-HighMed-Low

Low

1535139512001040

1470135011751020

140513001125990

133012251065960

124511551030910

11601080970860

1065985890785

935880780680

0480801 side

orbottom

HighMed-HighMed-Low

Low

1750149513101135

1685145512601105

1635140512251075

1575135511701040

152513051125995

144512501095995

138011851040910

13101120980860

060080

1 sideor

bottom

HighMed-HighMed-Low

Low

2200210018151560

2175202517601555

2085194517201515

2025186516701460

1925178516201435

1820170015501390

1735162014801340

1635154014051270

both sides or1 side and

bottom

HighMed-High

23601965

22801925

22101870

21301830

20351760

19601710

18751670

17901575

0481001 side

orbottom

HighMed-HighMed-Low

Low

1740150013401195

1705147013151175

1660144513001165

1615141012701130

1570137512351100

1500133012001070

1425128011401030

135512101095975

060100

1 sideor

bottom

HighMed-HighMed-Low

Low

2250202017251490

2175195016901480

2090190016601460

2020184016301440

1930179015751380

1855171015201340

1760164014601295

1670154513701230


bottom

HighMed-High

23601960

23151940

22651930

22001900

21301850

20551800

19651740

18901660

060120

bottomonly

HighMed-HighMed-Low

Low

2350210017701545

2250201517201520

2160195516751465

2070187516201415

2000181015751365

1885171015151325

1790165014501265

1635154013651185


bottom

HighMed-High

24352040

23602000

22851950

22201905

21301835

20501790

19651725

18751650

1 side only HighMed-High

22551985

21901930

21151890

20451840

19651780

18901720

18001645

17101560

060140

bottomonly

HighMed-HighMed-Low

Low

2285202016751460

2210197016501445

2140192016201430

2065187015901400

1990180515601370

1910173015101320

1830166014501275

1745159013901230


bottom

HighMed-High

23101975

22551945

21851900

21201860

20451835

19651775

18801720

18001640

1 side only HighMed-High

21401930

20801850

20251800

19451740

18751725

17951660

17251580

16251495

—13—

COMBUSTION AIR PIPE(DIRECT VENT/2-PIPE APPLICATION)

A/C COILOUTDOOR UNIT VENT PIPE

HUMIDIFIER

GAS-FIREDWATER HEATERELECTRONIC

AIR CLEANER

AIRFLOWFRONT OFFURNACE

COMBUSTIONAIR INLET(NON-DIRECT1-PIPE APPLICATION)

A05064

ELECTRONICAIR CLEANER

HUMIDIFIER

A/C COIL

VENT

COMBUSTIONAIR (DIRECT VENT/2 PIPE APPLICATION

OUTDOORUNIT

AIRFLOWFRONT OFFURNACE

A05065

COMBUSTION AIRINLET (NON-DIRECTVENT/ 1-PIPE APPLICATION

—14—

COMBUSTION–AIR PIPE


FURNACECONDENSATE

DRAIN

REFRIGERATIONPIPING

AIR CONDITIONINGCOIL

AIRFLOW

VENT PIPE

FRONT OF FURNACE

A05066

DIRECT VENT/2-PIPE APPLICATION)

COMBUSTION-AIR INLET(NON-DIRECT VENT/1-PIPE APPLICATION)

COMBUSTION– AIR PIPE(DIRECT VENT/2-PIPE APPLICATION)

VENTPIPE


FURNACE CONDENSATEDRAIN

AIRFLOW

AIR CONDITIONINGCOIL

REFRIGERATIONPIPING

FRONT OFFURNACE A05067

COMBUSTION - AIR INLET(NON-DIRECT VENT/1-PIPE APPLICATION)

—15—

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

UNIT MUST BE INSTALLED IN ACCORDANCEWITH INSTALLATION INSTRUCTIONS

Cancels: SS-PG9M-05

© 2005 Payne Heating & Cooling 7310 West Morris Street, Indianapolis, IN 46231 PRINTED IN U.S.A. Catalog No. SS-PG9MAB-01 9-05

—16—

Documents

Model PG9MAB MULTIPOISE CONDENSING GAS FURNACE · Model PG9MAB MULTIPOISE CONDENSING GAS FURNACE FEATURES INSTALLATION The 4-way multipoise design allows ... exchanger is positioned