MODEL ER-A460 MODEL ER-A470 - Inland Cash … MANUAL CODE: 00ZERA460VPME ELECTRONIC CASH REGISTER MODEL ER-A460 MODEL ER-A470 (For "V" version) SRV KEY : LKGIM7113RCZZ PRINTER : DP-730

PROGRAMMING MANUALCODE: 00ZERA460VPME

ELECTRONICCASH REGISTER

MODEL ER-A460MODEL ER-A470(For "V" version)SRV KEY : LKGIM7113RCZZPRINTER : DP-730

CHAPTER 1. SERVICE (SRV) MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

CHAPTER 2. PROGRAM (PGM2/PGM1) MODE . . . . . . . . . . . . . . . . . . . . . . . 14

CHAPTER 3. OP X/Z, X1/Z1, X2/Z2 MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

The ER-A460/A470 has the Easy Programming function which allows the user to

program easily.

This function is not described in this manual.

Please refer to the ER-A460/A470 EASY PROGRAMMING INSTRUCTION MANUAL of

an accessory for the product.

CONTENTS

SHARP CORPORATIONThis document has been published to be usedfor after sales service only.The contents are subject to change without notice.

ER-A460

ER-A470

CHAPTER 1. SERVICE (SRV) MODEThe SRV key is used for operating in the SRV mode.

1. SRV. reset (Program Loop Reset)

Used to return the machine back to its operational state after a lock-up has occurred.

Procedure

• Method 1

1) Turn off the AC switch.

2) Set the mode switch to (SRV′) position.

3) Turn on the AC switch.

4) Turn to (SRV) position from (SRV′) position.

• Method 2

1) Set the mode switch to PGM2 position.


3) While holding down JOURNAL FEED key and RECEIPT FEEDkey, turn on the AC switch.

Note: When disassembling and reassembling always power upusing method 1 only. Method 2 will not reset the CKDC6.

Note: SRV programming job#926-B must be set to "4" to allow PGMprogram loop reset.

PRG. RESET ***

2. Master reset (All memory clear)

There are two possible methods to perform a master reset.

• MRS-1Used to clear all memory contents and return machine back to itsinitial settings. return keyboard back to default. for default keyboardlayout.

Procedure


2) Set the MODE switch to the (SRV′) position.


4) While holding down JOURNAL FEED key, turn to (SRV) positionfrom (SRV′) position.

• MRS-2Used to clear all memory and keyboard contents.This reset returns all programming back to defaults. The keyboardmust be entered by hand.This reset is used if an application needs different keyboard layoutother than that supplied by a normal MRS-1.

Procedure


2) Set the MODE switch to the (SRV′) position.


4) While holding down JOURNAL FEED key and RECEIPT FEEDkey, turn to (SRV) position from (SRV′) position.

5) Key position assignment:

* After the execution of MRS-2, only the RECEIPT FEED andJOURNAL FEED keys can remain effective on key assignment.Any key can be assigned on any key position on the main key-board.

[key setup procedure]

MASTER RESET ***

NOTES:* 1: When the 0 key is pressed, the key of the key number on

display is disabled.* 2: Push the key on the position to be assigned. With this, the key

of the key number on display is assigned to that key position.

Key number Key name Key number Key name

1 Numeric key "0" 9 Numeric key "8"



4 Numeric key "3" 13 Decimal point key

5 Numeric key "4" 14 CL key

6 Numeric key "5" 15 ⊗ key

7 Numeric key "6" 16 ST key

8 Numeric key "7" 17 TL key

3. Reading of the SRV mode program

List of program reports

JOB# Report name

900SRV-mode program full item report (not incl. keyboardlayout)

950Keyboard layout report (on keys other than dept. keysand direct PLU keys)

951Keyboard layout report (on dept. keys and direct PLUkeys)

970 SRV file programming report

MRS-2 executed Key position set Free key

Disable

Free key setupcomplete.

*2

*1

0

0

– 1 –

[JOB# 900]All parameters contained for the SRV mode as listed

Key operation.

900 → & → 3

STAMP Stamp

01/01/00 0:00 Date/Time

000000 #0001 Machine No./Consecutive No.

#900 Job code

901# 0102 902# 0000

Contents of the SRV-modeprogramming

903# 4000 904# 0000 905# 0100 906# 0001

The contents of the programmingare printed only on the journalindividual formats shown at left.(No header is printed.)

907# 0014 908# 0000 909# 0000 910# 0004 911# 0000 912# 1141 913# 0002 914# 0100 915# 1020 916# 1000 917# 0000 918# 0000 919# 0000 920# 0000 921# 0000 922# 0000 923# 0000 924# 0000 925# 0000 926# 0000 927# 0000 928# 0000 929# 0000 980# 0000 930# z1 0000 Z1 reset counter

933# z1 0000 Hourly Z1 reset counter

934# z1 0000 PLU Z1/Z2 reset counter

935# z1 0000 Cashier Z1/Z2 reset counter

937# z2 0000 Z2 reset counter

939# z2 0000 Daily net Z2 reset counter

942#G T 2 *00000000000.00 GT2

943# G T 3 *00000000000.00 GT3

944# 0000 PGM2 mode secret code

945# 0000 Assignment Of RS232 channel

946# 0000 Assignment Of RS232 channel

948# 00 Training cashier No.

949# training Training mode title

[JOB# 950]The Key layout report is printed in SRV mode

Key operation

950 → & → 3

STAMP Stamp

01/01/00 0:02 Date/Time


#950 Job code

001 0 key 015 Key No./Key label/Location No.

002 1 key 016 003 2 key 024 004 3 key 032 005 4 key 017 006 5 key 025 007 6 key 033 008 7 key 018 009 8 key 026 010 9 key 034 011 00 key 023 012 000key 031

Key operation

951 → & → 3

STAMP Stamp

01/01/00 0:02 Date/Time


#951 Job code

001 ü ü é 055 Key No./key label/Location No.

002 ü ü â 056 003 ü ü ä 057 004 ü ü à 058 005 ü ü å 059 006 ü ü ç 060 007 ü ü ê 061 008 ü ü ë 062 009 ü ü è 063 010 ü é ü 064 011 ü é é 065 012 ü é â 066 013 ü é ä 067 014 ü é à 068 015 ü é å 069 016 ü é ç 070 017 ü é ê 071 018 ü é ë 072

– 2 –

[JOB#970]Files on the memory are listed.

Key operation

970 → & → 3

STAMP Stamp

01/01/00 0:03 Date/Time


#970 Job code

*001* 00018 /00018 File table No./No. of records

*002* 00018 /00018 /No. of used records

*003* 00018 /00018 *005* 00018 /00018 *006* 00018 /00018 *007* 00200 /00020 *008* 00200 /00020 *009* 00200 /00020 *012* 00200 /00020 *014* 00005 /00000 *015* 00005 /00000 *016* 00069 /00069 *017* 00069 /00069 *018* 00069 /00069 *019* 00004 /00004 *020* 00004 /00004 *021* 00004 /00004 *022* 00045 004/00045 File table No./No. of records/No. of blocks/No. of used records

*023* 00045 004/00045 *024* 00045 004/00045 *025* 00045 /00045 *026* 00045 /00045 *027* 00045 /00045 *028* 00045 /00045*029* 00049 /00049 *030* 00049 /00049 *031* 00032 /00000 *032* 00032 /00000 *033* 00070 /00070

1dbf80 File memory start address

1dff68 Empty memory start address

1dffff Memory end address

[JOB#990]Reading the Contents of the SRV-Mode Programming for SSP

Key operation

990 → & → 3

STAMP Stamp

01/01/00 0:03 Date/Time


#990 Job code

ssp era460v - 001 001 001 SSP No.

002 001 003 001 004 001 005 001 006 001 007 001

check sum error

– 3 –

4. Service mode programming

The following are the key operation required for programming.

Details of [A][B][C][D] will be discussed at each item description. mark is MRS setting.

[JOB #901]:MRS=0102#901-A: Not used (Fixed at "0")

#901-B: Tax system

1. TAX system 901-B

Auto TAX 1~3 0

Auto VAT 1~3 1

Manual VAT 1~3 2

Manual VAT 1 3

Manual TAX 1~3 4

Swiss TAX 5

#901-C: 1. Rounding system

1. Rounding system 901-C

Normal 0

SWEDEN 1

DENMARK 4

#901-D: 1. TAB setting

1. TAB setting 901-D

0. 0

0.0 1

0.00 2

0.000 3

[JOB#902] NOT USED MRS=0000

[JOB#903] MRS=4000#903-A: 1. IR communication baud rate

1. Baud rate (bps) 903-A

2400 2

4800 3

9600 4

19200 5

38400 6

57600 7

115200 8

* The communication speed with the ER-02FD is 19200bps.

#903-B, C, D: Not used (Fixed at "000")

[JOB#904] MRS=0000#904-A: 1. Printing of date

1. Printing of date 904-AYes 0

No 4

#904-B: 1. Printing of consecutive No.

1. Printing of consecutive No. 904-BYes 0

No 4

#904-C, D: Not used (Fixed at "00")

[JOB#905] MRS=0100#905-A: Not used (Fixed at "0")

#905-B: 1. Tax printing when taxable subtotal is zero.2. Tax printing when tax is zero.

1. Taxable subtotal iszero

2. Tax is zero905-B

SkipPrint 0

Skip 1

PrintPrint 4

Skip 5

#905-C: 1. Printing of rounding amount in receipt. (For Australia)2. Printing format for split pricing entry.

1. Printing of roundingamount in receipt

2. Printing format for splitpricing entry

905-C

NoNormal format 0

Australia format 1

YesNormal format 2

Australia format 3

#905-D : Not used (Fixed at "0")

[JOB#906] MRS=0001#906-A: 1. Print Dept. and PLU number on receipt.

2. Entry which makes the PLU stock counter negative

1. Print Dept. and PLUnumber on receipt.

2. Entry which makesthe PLU stockcounter negative

906-A

No

Allowed unconditionally 0

Operation alloweddespite ERROR

message1

Inhibited 2

Yes

Allowed unconditionally 4

Operation alloweddespite ERROR

message5

Inhibited 6

XXX TL

(Job#)

[A] [B] [C] [D]

Numeric entry4 digits max

0

– 4 –

#906-B: 1. Bottle return function2. Hash department setting

1. Bottle return function 2. Hash departmentsetting

906-B

DisableDisable 0

Enable 2

EnableDisable 4

Enable 6

#906-C: 1. Split pricing counting2. Multiplication entry

1. Split pricing counting 2. Multiplication entry 906-C

Quantity

Multiplication 0

Successivemultiplication

1

Split pricing 2

Package

Multiplication 4

Successivemultiplication

5

Split pricing 6

#906-D: 1. Presetting consecutive No.2. Fractional quantity

1. Presettingconsecutive No.

2. Fractional quantity906-D

YesNo 0

Yes (3 digit decimalplace)

1

NoNo 2

Yes (3 digit decimalplace)

3

[JOB#907] MRS=0014#907-A, B: Not used (Fixed at "00")#907-C: 1. In case of all cashier CCD and individual cashier CCD,

X1 report before CCD entry2. Locking of REG mode entry after individual cashier re-

setting3. Minus department and PLU

1. In case ofall cashierCCD andindividualcashierCCD, X1reportbefore CCDentry

2. Locking ofREG modeentry afterindividualcashierresetting

3. Minusdepartmentand PLU

907-C

DisableNo

Disable 0

Enable 1

YesDisable 2

Enable 3

EnableNo

Disable 4

Enable 5

YesDisable 6

Enable 7

#907-D: 1. Z-counter print for PLU, Hourly, Cashier, Daily net2. CCD compulsory

1. Z-counter print 2. CCD compulsory 907-D

YesNon compulsory 0

For individual cashier 1

For all cashier 2

NoNon compulsory 4

For individual cashier 5

For all cashier 6

[JOB#908] MRS=0000#908-A: GT print on Z report

GT1 (NET) GT2 (+) GT3 (–) 908-A

PrintPrint

Print 0

Skip 1

SkipPrint 2

Skip 3

SkipPrint

Print 4

Skip 5

SkipPrint 6

Skip 7

#908-B: GT print on X report

GT1 (NET) GT2 (+) GT3 (–) 908-B

SkipSkip

Skip 0

Print 1

PrintSkip 2

Print 3

PrintSkip

Skip 4

Print 5

PrintSkip 6

Print 7

#908-C: 1. Add void-mode transaction data to hourly total report2. X1/Z1 report in X2/Z2 mode3. Resetting of consecutive number in Z1 resetting

1. Addvoid-modetransactionto hourlytotal report

2. X1/Z1 reportin X2/Z2mode

3. Resetting ofconsecutiveNo.in Z1resetting

908-C

NoEnable

No 0

Yes 1

DisableNo 2

Yes 3

YesEnable

No 4

Yes 5

DisableNo 6

Yes 7

#908-D:1. Printing X/Z report Journal only/Receipt & Journal (Except the

individual cashier report)2. Z1 resetting, resets GT Enable/Disable

1. Printing X/Z report 2. GT resetting at Z1 908-D

Receipt & JournalDisable 0

Enable 1

JournalDisable 4

Enable 5

– 5 –

[JOB#909] MRS=0000#909-A: 1. Printing of training GT on the X report

2. Printing of training GT on the Z report

1. Printing of trainingGT on the X report

2. Printing of trainingGT on the Z report

909-A

SkipPrint 0

Skip 1

PrintPrint 2

Skip 3

#909-B: 1. Printing of data on PLU resetting report2. All Z1 resetting in X1/Z1 mode

1. Printing of data onPLU resetting report

2. All Z1 resetting inX1/Z1 mode

909-B

PrintEnable 0

Disable 2

SkipEnable 4

Disable 6

#909-C: 1. Printing of data in void-mode totalizer and manager voidtotalizer on Z2 report

2. Printing of data in void-mode totalizer and manager voidtotalizer on Z1 report

1. Void-mode totalizeron Z2 printing

2. Void-mode totalizeron Z1 printing

909-C

PrintPrint 0

Skip 2

SkipPrint 4

Skip 6

#909-D: Not used (Fixed at "0")

[JOB#910] MRS=0004#910-A: 1. Over laped cashier function

2. Over laped cashier function 910-A

No 0

Yes 1

#910-B: 1. Auto cashier sign off at the end of each transaction

1. Auto cashier sign off at the end ofeach transaction

910-B

No (After cashier Z1 only) 0

Yes (Everytime) 1

#910-C: Not used (Fixed at "0")

#910-D: 1. Cashier system

1. Cashier system 910-D

1 hole 1

Cashier code entry 4

[JOB#911] MRS=0000#911-A: 1. Fraction treatment

1. Fraction treatment 911-ARound off 0

Round up 1Round down 2


[JOB#912] MRS=1141#912-A: 1. Date print format

Date format 912-AMonth/Day/Year 0Day/Month/Year 1

Year/Month/Day 2

#912-B: 1. Time system

1. Time system 912-B12H 024H 1

#912-C: 1. After transaction receipt format2. Copy receipt3. Footer print control

1. Aftertransactionreceipt

2. Copyreceipt

3. Footer printcontrol 912-C

Total only

No

All receipt 0On selected functionkeys at the time offinalization

1

Yes


3

Detail

No

All receipt 4

On selected functionkeys at the time offinalization

5

Yes


7

#912-D: 1. Logo message control

1. Logo/stamp message control 912-D3-line header instead of a stamp 0Stamp only 1

Stamp and 3-line footer 26-line header instead of a stamp 33-line header + 3-line footer 5

(Logo/stamp message format)

Header

Footer

Type : 0 532

STAMPSTAMP

1

– 6 –

[JOB#913] MRS = 0002#913-A: 1. VP format on Receipt/Journal

2. Content of TOTAL VP amount

1. VP format 2. VP amount 913-A

Date & amountTotal amount 0

Tendered amount 1

Machine# & amountTotal amount 2Tendered amount 3

#913-B: 1. Printing of [ST]2. Escape the compulsion of VP

NOTE: Must turn to MGR mode and depress

• • , PRINT keys to escape validation

1. ST Print 3. Escape the compulsion of VP 913-B

NoDisable 0

Enable 1

YesDisable 4

Enable 5

#913-C: 1. Buzzer off 2sec. after lock error.2. Buffered keyboard

1. Error beep 2. Buffered keyboard 913-C

2-sec. offYes 0

No 1

ConstantYes 2

No 3

#913-D: 1. Drawer closing compulsory2. Error mode3. Key catch sound

1. Drawerclosingcompulsory

2. Error mode 3. Key catchsound 913-D

Non-compulsoryAll lock error

Enable 0

Disable 1

Miss operation(One shot error)

Enable 2

Disable 3

CompulsoryAll lock error

Enable 4

Disable 5

Miss operation(One shot error)

Enable 6

Disable 7

[JOB#914] MRS = 0100#914-A: 1. Receipt issuing at no-sale

2. [NS] key separation from [TL] key for no sale function

1. Receipt issuing atno-sale

2. [NS] key separation914-A

EnableYes 0

No 2

DisableYes 4

No 6

#914-B: 1. No-sale after NON ADD code entry

1. No-sale after # entry 914-B

Disable 0

Enable 1

#914-C 1. Action to be taken when the machine is locked by theReceipt/Journal paper near end check

2. Void mode

1. Action to betaken when themachine islocked by theReceipt/Journalpaper near endcheck

2. Void mode

914-C

Unlocked by CLkey

Enable 0

Disable 2

Enforcing of paperroll replacement

Enable 4

Disable 6

#914-D: 1. CHECK CASHING Enable/Disable

1. CHECK CASHING 914-D

Disable 0

Enable 2

[JOB#915] MRS = 1020#915-A: 1. Amount symbol

1. Amount symbol 915-A" $ " 0" * " 1

" " 2

#915-B: Not used (Fixed at "0")

#915-C: 1. Paper near end check2. ST (–), ST (%) as many times needed/operation only

once

1. Paper near endcheck

1. ST (–), ST (%)as many timesneeded/operation onlyonce

915-C

YesUnlimited 0

Once only 2

NoUnlimited 4

Once only 6


– 7 –

[JOB#916] MRS = 1000#916-A: 1. Print format when text and amount overlaps each other

REG mode

1. Print format when text and amountoverlaps each other REG mode

916-A

Truncate text 0

2 line print 1

#916-B: 1. Finalization by charge (credit) when ST t 0

1. Finalization by (credit) when SBTL t 0 916-B

Disable 0

Enable 4

#916-C: 1. Negative merchandise subtotal2. Subtotal entry compulsory before tendering3. Subtotal entry before direct non-tendering finalization

1. Negativemerchan-disesubtotal

2. Subtotalentrycompulsorybeforetendering

3 .Subtotalentry beforedirectnon-tenderingfinalization

916-C

AllowNoncompulsory

Non-compulsory 0

Compulsory 1

CompulsoryNon-compulsory 2

Compulsory 3

DisallowNon-compulsory

Non-compulsory 4

Compulsory 5

CompulsoryNon-compulsory 6

Compulsory 7

#916-D: 1. Coupon PLU printing on X/Z report2. Net sales subtotal (NET1) printing on X/Z report3. CHECK change total printing on X/Z report

1. Print couponPLU’s ongeneral report

2. Print netsales SBTL(NET1) ongeneral report

3. Print CHKCHANGE ongeneral report

916-D

PrintPrint

Print 0

Skip 1

SkipPrint 2

Skip 3

SkipPrint

Print 4

Skip 5

SkipPrint 6

Skip 7

[JOB#917] NOT USED: MRS = 0000

[JOB#918] MRS = 0000#918-A: 1. Printing of text of a tied PLU in set PLU

2. Dirrect non-tendering finalization after previous tenderentry

1. Printing of text of a tiedPLU in promo PLU

2. Dirrect non-tenderingfinalization afterprevious tender entry

918-A

YesDisable 0

Enable 2

NoDisable 4

Enable 6

#918-B: Not used (Fixed at "0")#918-C: 1. Printing Z1/Z2 counter in Z reports

1. Printing Z1/Z2 counter in Z reports 918-C

Print 0

Skip 4


[JOB#919] MRS = 0000#919-A, B: Not used (Fixed at "00")

#919-C: 1. Amount printing when PLU unit price is 0

1. Amount printing when PLU unit price is 0 919-C

No 0

Yes 1

919-D: 1. Conversion ST printing of native ST

1. Conversion SBTL print of native SBTL 919-D

Yes 0

No 4

[JOB#920] NOT USED MSR = 0000

[JOB#921] NOT USED MRS = 0000





[JOB#926] MRS = 0000#926-A: Not used (Fixed at "0")

#926-B: 1. Program reset at PGM 2 mode

1. Program reset at PGM2 mode 926-B

Disable 0

Enable 4

#926-C, D: Not used (Fixed at "00")

– 8 –

[JOB#927] MRS = 0000#927-A: 1. Rounding up of the units digit of amount

#927-B: 1. Rounding down of the units digit of amount

1. Rounding the units digit of amount 927-AB

Common destination 00

Netherland/Switzerland 82

Norway 54

#927-C: 1. Difference memory (Difference between before-rounding and after-rounding)

2. Limit on the least sighificant digit in entering the amounton item

1. Difference memory 2. Limit on the leastsighificant digit inentering the amounton item

927-C

NoArbitary 0

0 only 1

0 and 5 only 2

YesArbitary 4

0 only 5

0 and 5 only 6

#927-D: 1. Application of rounding2. Limit on the least significant digit in entering the amount

of payment

1. Application of rounding 2. Limit on the leastsignificant digit inentering the amountof payment

927-D

Item & PaymentArbitary 0

0 only 10 and 5 only 2

PaymentArbitary 40 only 5

0 and 5 only 6



[JOB#980] MRS = 0000#918-A, B, C: Not used (Fixed at "000")#980-D: 1. Language selection of guidance message

1. Language selection of guidancemessage

910-D

English 0

German 1

[JOB#930 ∼939] MRS = 0000RESET REPORT COUNTER

JOB # Function

930 Z1 report counter

933 Hourly Z1 report counter

934 PLU Z1/Z2 report counter

935 Cashier Z1/Z2 report counter

937 Z2 report counter

939 31 day daily net Z2 report counter

[JOB#942, 943] MRS = 0000000000000GT COUNTER PRESETTING

JOB # Function942 GT2 (Positive GT)943 GT3 (Negative GT)

Note: GT1 is obtained by calculationEquation: GT1=GT2-GT3

[JOB#944] MRS = 0000PGM1/2 secret code presetting

NOTE: When the secret code "0" is programmed, the secret codeentry is be inhibited.

[JOB#945] MRS = 0000The assignment of RS232 channel by each devices

* For use, the option control ROM (ER-A46R1) and the RS232 I/F(ER-A5RS) are required.

#945-A: 1. Channel No. for online

1. Channel No. for online 945-A

Channel No. 0 to 7


* 0 = No connect1 to 7 = Channel number


[JOB#948] MRS = 000000PROGRAMMING OF TRAINING CASHIER NO.

[JOB#949] MRS = "TRAINING"THE TRAINING MODE’S TITLE

Characters can be entered by using alphabetic keys or numeric keys.Please refer to section 3.

[JOB#989]RESETTING OF ALL COUNTER AND TOTALIZER

Job# ABCD

Initial value of Z countr

"0000"

TL

Job# 000000000000013 digits

0

TL

944 XXXX4 digits

0

TL

Job# ABCD

0

TL

948 XX TL

XX: Cashier No.

949 Character Key(8chra.)

Space

TL

989 TL

– 9 –

[JOB#950] MRS = STANDARD KEY LAYOUTFree key layout (Except for department keys and direct PLU keys.)

[JOB#951] MRS = STANDARD KEY LAYOUTFree key layout (department keys and direct PLU keys)

• Programming of the keys to be dept keys or direct PLU keys onthe keyboard.

• Key No. is assigned to each key which is supposed to be dept.Key or direct PLU key by depressing the key after entering the keyNo.

• Those keys programmed by this job No. will be dept. keys if dept.code is assigned, and will be direct PLU keys if PLU code isassigned in the PGM2 mode.

FUNCTION KEY LIST

Key No. KEY KEY TEXT

1 0 KEY 0 KEY

2 1 KEY 1 KEY

3 2 KEY 2 KEY

4 3 KEY 3 KEY

5 4 KEY 4 KEY

6 5 KEY 5 KEY

7 6 KEY 6 KEY

8 7 KEY 7 KEY

9 8 KEY 8 KEY

10 9 KEY 9 KEY

11 00 KEY 00 KEY

12 000 KEY 000KEY

13 DECIMAL POINT . KEY

14 CLEAR CLEAR

15 ⊗

16 ST SBTL

17 TL TOTAL

18 # #

19 NO SALE NS

20 PLU PLU

21 G. C. COPY GCCOPY

22 Level1 L1

23 Level2 L2

24 Level3 L3

25 PRINT VP

26 RCPT RCPT

27 VOID VOID

28 REFUND RFND

Key No. KEY KEY TEXT

29 %1 %1

30 %2 %2

31 %3 %3

32 %4 %4

33 (–)1 (–)1

34 (–)2 (–)2

35 (–)3 (–)3

36 (–)4 (–)4

37 VAT VAT

38 AUTO AUTO

39 AUTO2 AUTO2

40 AUTO3 AUTO3

41 AUTO4 AUTO4

42 AUTO5 AUTO5

43 CASH2 CA2

44 CHECK1 CHECK1

45 CHECK2 CHECK2

46 CHECK3 CHECK3

47 CHECK4 CHECK4

48 CR1 CR1

49 CR2 CR2

50 CR3 CR3

51 CR4 CR4

52 CONV1 EX1

53 CONV2 EX2

54 CONV3 EX3

55 CONV4 EX4

59 RA RA

60 RA2 RA2

61 PO PO

62 PO2 PO2

63 1⁄2 1⁄2 KEY

64 AMT AMT

65 VAT SHIFT VAT SF

66 CASHIER NO. CASH#

67 DIFFER ST DIF ST

ER-A460 KEY POSITION

R J 16 22 28 34 40 46 52 58 64 70 76 825 10 15 21 27 33 39 45 51 57 63 69 75 814 9 14 20 26 32 38 44 50 56 62 68 74 803 8 13 19 25 31 37 43 49 55 61 67 73 792 7 12 18 24 30 36 42 48 54 60 66 72 781 6 11 17 23 29 35 41 47 53 59 65 71 77

ER-A470 KEY POSITION

R J 22 30 38 46 54 62 70 78 86 94 102 110 1187 14 21 29 37 45 53 61 69 77 85 93 101 109 1176 13 20 28 36 44 52 60 68 76 84 92 100 108 1165 12 19 27 35 43 51 59 67 75 83 91 99 107 1154 11 18 26 34 42 50 58 66 74 82 90 98 106 1143 10 17 25 33 41 49 57 65 73 81 89 97 105 1132 9 16 24 32 40 48 56 64 72 80 88 96 104 1121 8 15 23 31 39 47 55 63 71 79 87 95 103 111

950 Free key

Key number automaticincrement

Key number manualincrement

Initial setting

XXXKey No.

To inhibit

TL

951 Free keyXXXKey No.

Key number automaticincrement

Key number manual increment

To inhibit

TL

– 10 –

[JOB#971]SRV FILE PROGRAMMING. (File creation deletion and change ofrecord count or block count)

Key operation

• Normal file

GroupNo.

File name Type* File table No.(Create/Erase)

1Dept.

101, 02, 03, 05,37, 40, 42

2 Dept Text (8chra.) 0 03

3 Dept Text (12chra.) 0 04

4 PLU 1 07, 08, 09, 12

5 PLU Text (8chra.) 0 09

6 PLU Text (12chra.) 0 10

7 PLU stock 0 11

8 Link PLU 1 14

9 Set PLU 1 15

10Cashier

119, 20, 21, 22,23, 24, 34, 37,38, 39

11Cashier Dept

037, 38, 40, 41,42, 43

12 Hourly 1 29, 30

13 Daily net 1 31, 32

14 Reg. buffer 1 33, 34

15 Overlapped cashier 0 34

16 Message Text 0 35

17 Guidance Text 0 36

18 Term Dept. 0 06

19 Term PLU 0 13

20 Term Transaction 0 18

21 Term Cashier 0 24

22 Term Cashier Dept 0 39

23 All of term file 0 06, 13, 18, 24, 39

Type = 0 ; Create/Erase onlyType = 1 ; Create/Erase and Increase/decrease the number of

Records or blocks. * : The files which are created or erased by the entry of group

No.

971 @/FOR abcFile group No.

delete

XXXXXNumber of records

TL

– 11 –

File table

TableNo.

File nameRECORD BLOCK Label

sizeDatasizeMRS Max. #1 MRS Max. #2

1 Dept. Preset 18 50 1 1 1 6

2 Price 18 50 (1) 1 1 0 3

3 Text (8chra.) 18 50 (1) 1 1 0 8

4 Text (12chara.) 0 50 (1) 0 1 0 12

5 Daily 18 50 (1) 1 1 0 9

6 Term 18 50 (1) 1 1 0 9

7 PLU Preset 200 *** 1 1 3 6

8 Price 200 *** (7) 1 1 0 3

9 Text (8chra.) 200 *** (7) 1 1 0 8

10 Text (12chra.) 0 *** (7) 0 1 0 12

11 Stock 0 *** (7) 0 1 0 4

12 Daily 200 *** (7) 1 1 0 9

13 Term 0 *** (7) 0 1 0 9

14 Link PLU 5 *** 1 1 3 15

15 Set PLU 5 *** 1 1 3 30

16 Transaction Label 69 69 1 1 2 0

17 Daily 69 69 (16) 1 1 0 8

18 Term 69 69 (16) 1 1 0 8

19 Cashier Preset 4 15 1 1 1 3

20 Flag 4 15 (19) 1 1 0 2

21 Text 4 15 (19) 1 1 0 8

22 Cashier transaction Label 45 45 4 15 (19) 2 0

23 Daily 45 45 (22) 4 15 (19) 0 8

24 Term 45 45 (22) 4 15 (19) 0 8

25 Reset Csr trns. Label 45 45 1 1 2 0

26 Daily 45 45 (25) 1 1 0 8

27 Total cashier (Buffer) Label 45 45 1 1 2 0

28 Total 45 45 (27) 1 1 0 8

29 Hourly Label 49 49 1 1 1 0

30 Daily 49 49 (29) 1 1 0 8

31 Daily net Label 32 32 1 1 3 0

32 Total 32 32 (30) 1 1 0 8

33 Reg. buffer 70 255 1 1 0 36

34 Over lapped Csr 0 255 0 15 (19) 0 36

35 Message Text 0 87 0 1 2 12

36 Guidance Text 0 132 0 1 2 12

37 Csr trns. Dept Label 0 50 0 15 (19) 1 0

38 Daily 0 50 (37) 0 15 (19) 0 9

39 Term 0 50 (37) 0 15 (19) 0 9

40 Reset Csr Dept trns. Label 0 50 0 1 1 0

41 Daily 0 50 (40) 0 1 0 9

42 Total Csr (Buffer) Dept Label 0 50 0 1 1 0

43 Total 0 50 (41) 0 1 0 9

(#1) : Same as the number of record of table no. N(#2) : Same as the number of block of table no. N

– 12 –

[JOB#996, 998] IR data send/receive (ECR↔ECR, ECR↔ER-02FD)

[JOB#996] IR data send

X : SSP = 0

• Send to ECR (IrDA) : IrDA(Enable baud-rate : 115200bps,

57600bps, 38400bps,19200bps, 9600bps,4800bps, 2400bps)

• Send to ER-02FD + CE-IR2 (CE-IR4) : ASK(Enable baud-rate : 19200bps)

• Send to ECR (ASK) : ASK(Enable baud-rate : 57600bps, 38400bps,

19200bps, 9600bps,4800bps, 2400bps)

[JOB#998] IR data receive

• Receive from ECR (IrDA) : IrDA(Enable baud-rate : 11500bps, 57600bps,

38400bps, 19200bps,9600bps, 4800bps,2400bps)

• Receive from ER-02FD + CE-IR2 (CE-IR4) : ASK(Enable baud-rate : 19200bps)

• Receive from ECR (ASK) : ASK(Enable baud-rate : 57600bps, 38400bps,

19200bps, 9600bps,4800bps, 2400bps)

996

All data

X

Send to ECR(IrDA)

Send to ER-02FD or ECR(ASK)

ST

TL

998

Receive from ECR(IrDA)

Receive from ER-02FD or ECR(ASK)

ST

TL

– 13 –

CHAPTER 2. PROGRAM(PGM2/PGM1) MODE

1.Reading of the PGM mode program

[JOB#1100]: DEPT readingKey operation

STAMP Stamp

01/01/00 0:04 000000 #0009

#1100 *P G M â * Job Code/Mode title

01-10 Start No. – End No.

D 01 0.00 Dept. code/Taxable/Sign, Price

dpt.ü é g01 Text/Group No.

0000001 col17 Program (* 1) Commission Group/HALO

D 02 0.00 dpt.ü â g01 0000001 col17 D 03 0.00 dpt.ü ä g01 0000001 col17 D 04 0.00 dpt.ü à g01 0000001 col17 D 05 0.00 dpt.ü å g01 0000001 col17 D 06 0.00 dpt.ü ç g01 0000001 col17 D 07 0.00 dpt.ü ê g01 0000001 col17 D 08 0.00 dpt.ü ë g01 0000001 col17 D 09 0.00 dpt.ü è g01

(* 1) PROGRAM: ABCDEFGA: Printing on the cashier report Yes/No 1/0B: Item vp compulsory/noncompulsory 1/0C: (Not used) 0D: (Not used) 0E: SIF/SICS/Normal 2/1/0F: (Not used) 0G: Amount entry type

Open and preset/preset/open/inhibited 3/2/1/0

[JOB#1200]: PLU readingKey operation

STAMP Stamp

01/01/00 0:05 000000 #0011


000001-000005 Start No. – End No.

P 000001(ü é ) /00 PLU code (Dept code)/(* 1)/Base q’ty

0.00 Taxable/Sign, Price

pl000001 co Text/Commission Group

002 Program (* 2)/Stock

P 000002(ü é ) /00 0.00 pl000002 co 002 P 000003(ü é ) /00 0.00 pl000003 co 002 P 000004(ü é ) /00 0.00 pl000004 co 002

(* 1) NORMAL. LINK PLU. SET MENU: NORMAL: L LINK PLU: S SET MENU

(* 2) PROGRAM: ABCA: (Not used) 0B: (Not used) 0C: Amount entry type

Open and preset/preset/open /inhibited = 3/2/1/0 (PLU) (Sub-dept)

1100 XXStart No.

XXEnd No.

Single item

All

TL

1200 XXXXStart No. End No.

Single item

XXXX

All

TL

– 14 –

[JOB#1220]: STOCK ADD PRESET

STAMP Stamp

01/01/00 0:06 000000 #0005


P 000001 1000.000 Old stock

10.000 (Input stock)

s 1010.000 New stock

[JOB#1221]: STOCK SUB PRESET

STAMP Stamp

01/01/00 0:06 000000 #0005 #1221 *P G M é * Job code/Mode title

P 000001 1000.000 Old stock

-10.000 (Input stock)

s 990.000 New stock

[JOB#1222]: STOCK INVENTORY PRESET

STAMP Stamp

01/01/00 0:06 000000 #0005 #1222 *P G M é * Job code/Mode title

P 000001 1000.000 Old stock

500.000 (New stock) - (Old stock)

s 15000.000 New stock (Input stock)

[JOB#2220]: LINK PLU PRESET OR READINGKey operation

STAMP Stamp

01/01/00 0:06 000000 #0010

#2220 *P G M â * Job code/Mode title

000001-999999 Start No. – End No.

P 000002 L p000011 PLU code/Link PLU code (Max 5) p000012 /Link PLU code

[JOB#2221]: SET MENU PRESET OR READINGKey operation

STAMP Stamp

01/01/00 0:06 000000 #0011


000001-999999 Start No. – End No.

P 000001 S p000002 PLU code/Set PLU code (Max. 10)

p000003 /Set PLU code

[JOB#1300]: FUNCTION PRESET READINGKey operation

2220Start No. End No.

Single item

XXXXXX XXXXXX

All

TL

2221Start No.

XXXXXX

All

End No.

Single item

XXXXXX TL

1300 TL

– 15 –

STAMP Stamp

01/01/00 0:06 000000 #0015


F 001[ ~ ] é Function No./Text

S -0.00 Sign, Rate

l17 HALO

F 002[ ~ ] â S -0.00 l17 F 005 ‰ é S -0.00% Rate

l100.00% F 006 ‰ â S -0.00% Rate

l100.00% F 009 set plu- F 011 tax1 stF 012 tax2 stF 013 tax3 stF 015 vat 1F 016 vat 2F 017 vat 3F 019 N E T éF 020 N E T âF 021 cp pluF 022 refundF 023 \F 024 ¡ modeF 025 mgr ¿F 026 sbtl ¿F 029 vat sftF 030 tax deleF 031 vp cntF 032 no sale HALO

F 033 g.c. cntF 036 ***ra l18F 038 ***po l18F 041 C ash l18 00000000000 (* 1) PGM

F 043 check l18 00000000000 F 047 credit1 l18 00000000000F 048 credit2 l18 00000000000F 051 exch1 0.0000F 058 ****cid 9999999.99F 060 ca/ch id F 061 chk/cg 999999.99 F 062 guestF 063 com.sal1 0.00%F 064 com.sal2 0.00%F 065 com.sal3 0.00%

F 066 non com.F 067 order tlF 068 paid tlF 069 dom.cur1F 073 *ch idF 074 *dept tlF 075 dept(-)F 080 net 1F 081 net 2F 082 net 3F 084 subtotalF 085 mdse stF 086 ***totalF 087 changeF 088 dueF 089 itemsF 090 plu stF 091 C O P YF 092 g.c copyF 093 ave.F 094 G roup01 F 095 G r0up02F 096 G roup03F 097 G roup04F 098 G roup05F 099 G roup06F 100 G roup07F 101 G roup08F 102 G roup09F 106 O ~ PF 107 com.amt1F 108 com.amt2F 109 com.amt3F 110 ccm.ttlF 111 D E P TF 112 groupF 113 P L UF 114 stockF 115 trans.F 116 tl-idF 117 salesF 118 cashierF 119 hourlyF 120 dailyF 121 set pluF 122 ttl taxF 123 N E TF 124 zero salF 125 category

(* 1) PGM: ABCDEFGHIJKA: EFT function compulsory/noncompulsory 1/0B: Footer print Yes/No 1/0C: Non-add code entry compulsory/noncompulsory 1/0D: Change due Disable/Enable 1/0E: VP compulsory/noncompulsory 1/0F: (Not used) 0G: (Not used) 0H: (Not used) 0I: (Not used) 0J: Drawer opening No/Yes 1/0K: Entry of amount tenderd

compulsory/noncompulsory compulsory/inhibit

(Cash, check) 1/0(CR1 to 8) 1/0

– 16 –

[JOB#2600]: READING OF OTHERKey operation

STAMP Stamp

01/01/00 0:08 000000 #0017


#2615 10 SLIP/VP

#2616 (* 1) Optional feature

01 00000000 02 00000000 03 00000000 04 00000000 05 00000000 06 00000000 07 00000000 08 00000000 09 00000000 10 00000000 11 00000000 12 00000000 13 00000000#2617 000 Till timer

#2619 0 00 (* 3) Hourly report

#2620 Stack report 1

#2630 0000 Secret code PGM1

#2631 0000 X1/Z1

#2632 0000 X2/Z2

(* 1) Optional feature: ABCDEFGH

MRS = 00000000

x: 1 MRS = 00000000A: OP X/Z report Disable/Enable 1/0B: PO operation in REG mode Disable/Enable 1/0C: (Not used) 0D: "RFND" key entry in REG mode Disable/Enable 1/0E: Direct void function in REG mode Disable/Enable 1/0F: Indirect void in REG mode Disable/Enable 1/0G: Subtotal void in REG mode Disable/Enable 1/0H: Refund VP Compulsory/Non compulsory 1/0

x: 2 MRS = 00000000A: The first last item void Disable/Enable 1/0B: PLU level shift system Manual/Auto 1/0C: PLU level shift system MGR/MGR & REG 1/0D: Printing of the number of purchases Yes/No 1/0E: Time print No/Yes 1/0F: Journal select/Full print 1/0G: Item VP Disable/Enable 1/0H: (–) VP Compulsory/Non compulsory 1/0

x: 3 MRS = 00000000A: (Not used) 0B: (Not used) 0C: Zero skip in Cashier report No/Yes 1/0D: Zero skip in Transaction report No/Yes 1/0E: Zero skip in DEPT. report No/Yes 1/0F: Zero skip in PLU report No/Yes 1/0G: Zero skip in hourly report No/Yes 1/0H: Zero skip in Daily net report No/Yes 1/0

x: 4 MRS = 00000000A: (Not used) 0B: (Not used) 0C: Vat/Tax amount printing on R/J No/Yes 1/0D: Taxable amount printing on R/J No/Yes 1/0E: Net amount printing on R/J No/Yes 1/0F: (Not used) 0G: (Not used) 0H: When PLU level system is "Auto" (x: 2 B = 0),

PLU level returns to level 1 by one receipt/by one item. 1/0

x: 5 MRS = 00000000A: (Not used) 0B: (Not used) 0C: (Not used) 0D: VAT shift system By shift key/by cashier 1/0E: (Not used) 0F: (Not used) 0G: (Not used) 0H: (Not used) 0

x: 6 (Not used) MRS = 00000000

x: 7 (Not used) MRS = 00000000

x: 8 (Not used) MRS = 00000000

x: 9 (Not used) MRS = 00000000

x: 10 (Not used) MRS = 00000000

x: 11 (Not used) MRS = 00000000

x: 12 (Not used) MRS = 00000000

x: 13 MRS = 00000000A: Credit totalizer update if RA/PO finalized

by Credit key Yes/No 1/0B: Separater line in report Separater line/1 line 1/0C: (Not used) 0D: (Not used) 0E: (Not used) 0F: (Not used) 0G: (Not used) 0H: (Not used) 0

(* 2) Hourly report : a bca: Hourly report format by 15 minutes/by 30 minutes 1/0bc: start hour 00 to 23

2600 TL

2616 X ABCDEFGH

0

ST TL

– 17 –

[JOB#2640]: READING OF TEXT PROGRAMMINGKey operation

STAMP Stamp

01/01/00 0:08 000000 #0019


#2641 01 entry error Message text

02 misoperation 03 no record 04 paper empty 05 secret code 06 07 memory full 08 09 10 out of stock11 sbtl compul.12 tend compul.13 14 15 16 17 18 19 20 21 22 cashier err.23 entry err ca24 25 26 27 28 29 30 31 # compulsory32 not assigned33 not change34 over limit.35 inh. open pr36 inh. unit pr37 not non-tend38 39 p off in vp40 41 42 43 44 45 46

47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 buffer full68 69 70 71 72 eft error73 eft break74 75 76 close drawer77 78 79 80 81 entr secret#82 send83 receive84 send ok85 receive ok86 com. error87 data error88 time out89 cancel#2644 001 dept price Guidance

002 dept func. 003 dept taxable 004 dept halo 005 dept text 006 dept com.grp 007 dept group 008 dept drctkey009 plu asg.dept 010 plu price 011 plu base qty012 plu stck add013 plu stck sub014 plu stck ovw015 plu function016 plu taxable017 plu text018 plu com.grp019 plu drct key020 link plu

2640 TL

– 18 –

021 set plu022 plu code rng023 plu func rng024 plu stts rng025 plu com rng026 rate prgram027 misc key pgm028 fnc key halo029 mdiakey halo030 % halo031 func text032 misc key pgm033 misc key pgm034 mdia key pgm035 mdiakey halo036 csr code pgm037 csr name pgm038 csr pgm039 date program040 time program041 mchn no. pgm042 cc no. pgm043 logotext pgm044 vp count045 opt feature046 drawer alarm047 hourlyreport048 stack report049 secret(pgm1)050 secret(x1z1)051 secret(x2z2)052 messge text053 guid text054 tax rate055 price056 enter dept#057 sign (-)058 sign (+)059 taxable1:yes060 taxable1:no061 taxable2:yes062 taxable2:no063 taxable3:yes064 taxable3:no065 vat:yes066 vat:no067 prt csr:yes068 prt csr:no069 vp compl:yes070 vp compl:no071 sif072 sics073 normal074 delete075 open&prest076 preset077 open078 inhibited079 halo(exp.)080 halo(amount)081 halo(rate)082 com.grp083 group084 base q’ty

085 stock(add)086 stock(sub)087 stock(over)088 rate089 item090 st091 eft cmpl092 eft noncmpl093 footer :yes094 footer :no095 # cmpl096 # noncmpl097 due disable098 due enable099 drw open:yes100 drw open:no101 tnd cmpl:yes102 tnd cmpl:no103 tnd inh.104 enter plu#105 ent.csr code106 ent.csr no107 ent.drw#108 g.c copy yes109 g.c copy no110 vat sft stat111 vat sft not112 ent.dept#113 ent.key#114 ent.func#115 ent.pos.code116 enter tax no117 ent.tax rate118 lower tax119 enter msg no120 enter gid no121 (fixed data)122 entercoookey‘123 data send124 data rcv.125 org’zer rcv.126 onl t.no.127 onl modem128 onl baudrate129 onl code130 onl timer

– 19 –

[JOB#2900]: AUTO KEY READINGKey operation

STAMP Stamp

01/01/00 0:08 000000 #0005


#üé 1 key 0 key 0 key total#üâ D ü é (DEPT01)

D ü â P 000001 (PLU000001)

:#üå 1 key 0 key 0 key total check

[JOB#1500]: CASHIER READING REP.Key operation

STAMP Stamp

01/01/00 0:08 000000 #0016


01csr# 01 Cashier code/Name

0000d1 Drawer No.

02csr# 02 0000d1 03csr# 03 0000d1 04csr# 04 0000d1

[JOB#2700]: TAX TABLE READING REP.Key operation

STAMP Stamp

01/01/00 0:08 000000 #0005


tax1 10.0000% VAT No./Rate

04.00 Lower tax limit

tax2 4.0000% VAT No./Rate

0.00 Lower tax limit

tax3 5.0000% 0.00

2900 TL 1500 TL

2700 TL

– 20 –

[JOB#2119]: DIRECT KEY READING REP.Key operation

STAMP Stamp

01/01/00 0:08 000000 #0005


ü ü é l1 D ü é Key no./Dept code or PLU codeü ü â l1 D ü â *** When Dept code is assigned to

ü ü ä l1 D ü ä *** the direct key, the same Dept

ü ü à l1 D ü à *** code isassigned to each level.

Çü å é l1 P 000001 l2 P 001001ü å â l1 P 000002 l2 P 001001 Çé å é l1 ---- Ç

2. Programming

[JOB#1110]PROGRAMMING OF DEPT. PRICE

XX: DEPT-CODE = 01 ∼ 50YYYYYY: PRICE = 0 ∼ 999999Preset price is max. 6 digits.Price can be programmed for each dept. If this programming is per-formed, the ECR is automatically programmed to allow preset priceentry even when it has been programmed not to allow preset priceentry in dept. function programming (JOB#2110).

MRS = 000000

[JOB#2110]PROGRAMMING OF DEPT. FUNCTION

XX: DEPT. code = 01 ∼ 50

XXA: Printing on the cashier report A

No 0

Yes 1

XXB: Item validation printing B

Non compulsory 0

Compulsory 1

C, D: Not used (Fixed at "00")

XXE: SICS Function E

Normal 0

Single item cash sale 1

Single item finalize 2

F: Not used (Fixed at "0")

XXG: Amount entry type G

Inhibited 0

Open 1

Preset 2

Open and preset 3

MRS = 0000001

2119 TL

1110 YYYYYYXX

No change

priceDEPT. CODE

For the next DEPT.

TLST

2110 XX

DEPT. CODE

CL

ABCDEFG

For next code

No change

TLST

– 21 –

[JOB#2111]DEPT. TAX STATUS PROGRAMMING

XX: DEPT. CODE = 01 ∼ 50 A, B: Not used (Fixed at "00")

C: VAT 1 C

Non taxable 0

Taxable 1

D: Taxable 3 D

Non taxable 0

Taxable 1

E: Taxable 2 E

Non taxable 0

Taxable 1

F: Taxable 1 F

Non taxable 0

Taxable 1

MRS = 000000

[JOB#2112]DEPT. HALO (limit) preset

XX: DEPT. CODE = 01 ∼ 50A: Mantissa (HALO) = 1 ∼ 9B: Exponent (HALO) = 0 ∼ 7

* Items A and B indicate A × 10B. Any amount below that value isenable within 9999999.

MRS = 17

[JOB#2114]DEPT. TEXT PROGRAMMING

XXX: DEPT. CODE = 01 ∼ 50

Characters can be entered by using alphabetic keys or numeric keys.Please refer to section 3.

MRS = DPT. XX

[JOB#2115]COMMISSION GROUP PROGRAMMING

XX: DEPT. CODE = 01 ∼ 50A: Group No. = 0~3

[JOB#2116]PROGRAMMING OF DEPT. GROUP

XX: DEPT. code = 01 ∼ 50AA: Group No. = 1 ~ 14

Group No. Group name

1~9 Plus department

10 Minus department

11 Plus HASH department

12 Minus HASH department

13 Plus BR department

14 Minus BR department

MRS = 01

A selection of the group "Hash" and "BR" are inhibited when the hashfunction is programmed as disabled in SRV mode.

[JOB#2119]LINK NUMBER PROGRAMMING FOR DIRECT DEPT. KEYS

DEPT. code is assigned to the key no. Which has been programmedin JOB#951 programming.

AB: DEPT. CODE = 01 ∼ 50

[JOB#1200]Creating/assigning PLUs and the associated departments.

XXXXXX: PLU code = 01 ∼ 999999AB: DEPT. code = 01 ∼ 50

If the record of entered PLU code is not in PLU file at this program-ming, it will be created in PLU file.

MRS = 01

2111 XX

DEPT. CODE

CL

ABCDEF

For the next DEPT.

No change

ST TL

2112 ABXX

DEPT. CODE

For the next DEPT.

No change

TLST

2114 XX

DEPT. CODE

CL

Character key

For the next DEPT.

No change

ST TL

2115 XX

DEPT. CODE

CL

A

For next code

No change

TLST

2116 XX

DEPT. CODE

CL

AA

Next code

No change

TLST

2119 XXX

KEY No.

Next DEPT.

ABDEPT. code

0

ST TL

1200 XXXXXX

PLU code

AB

No change

ST TL

– 22 –

[JOB#1210]PRICE PROGRAMMING FOR PLUS

XXXXXX: PLU CODE = 1 ∼ 999999YYYYYY: Amount = 0 ∼ 999999


MRS = 000000

[JOB#1211]PLU BASE Q’TY PROGRAMMING

XXXXXX: PLU code = 1 ∼ 999999ZZ: Base quantity = 00 ∼ 99


[JOB#1220]PROGRAMMING OF PLUS STOCK (ADD)

XXXXXX: PLU code = 1 ∼ 999999YYYY.YYY: Stock value = 0.001 ∼ 9999.999

The stock value is max. 7 digits. (4 integers + 3 decimals) The stockvalue entered is added to the PLU stock counter.

MRS = 0.000

[JOB#1221]PROGRAMMING OF PLU STOCK (SUB)

XXXXXX: PLU code = 1 ∼ 999999YYYY.YYY: Stock value = 0.001 ∼ 9999.999

The stock value is max. 7 digits. (4 integers + 3 decimals) The stockvalue entered is subtracted from the PLU stock counter.

MRS = 0.000

[JOB#1222]PROGRAMMING OF PLU STOCK (OVERWRITE)

XXXXXX: PLU code = 1 ∼ 999999YYYYYYY: Stock value = 0.001 ∼ 9999.999

The stock value is max. 7 digits. (4 integers + 3 decimals) The stockvalue entered is overrited to the PLU stock counter.

MRS = 0.000

[JOB#2210]PLU function programming

XXXXXX: PLU code = 1~999999 A, B: Not used (Fixed at"00")

C: Amount entry type C

Inhibited 0

Open 1

Preset 2

Open and preset 3

Delete 4


MRS = 002

1210 XXXXXX

PLU CODE

YYYYYY

For next code

No change

ST TL

1211 ZZXXXXXX

PLU CODE

For the next PLU

No change

TLST

1220 YYYY.YYYXXXXXX

PLU CODE

For the next PLU

ST TL

1221 XXXXXX

Next codePLU CODE

YYYY.YYY ST TL

1222 XXXXXX

PLU CODE

YYYYYYY

Next code

No change

ST TL

2210 ABCXXXXXX

No change

PLU code

For next codeCL

ST TL

– 23 –

[JOB#2211]PLU TAX STATUS PROGRAMMING

XXXXXX: PLU code = 1 ∼ 999999

A: Sign A

+ 0

– 1

XXXXXB: Not used (Fixed at "0")

C: VAT 1 C

Non taxable 0

Taxable 1

D: Taxable 3 D

Non taxable 0

Taxable 1

E: Taxable 2 E

Non taxable 0

Taxable 1

F: Taxable 1 F

Non taxable 0

Taxable 1


MRS = 000000

[JOB#2214]PLU TEXT PROGRAMMING

XXXXXX: PLU CODE = 1 ∼ 999999Characters can be entered by using alphabetic keys or numeric keys.Please refer to section 3.

MRS = PLXXXXXX

[JOB#2215]COMMISSION GROUP PROGRAMMING

XXXXXX: PLU code = 1 ~ 999999XXXXXA: Group No. = 0 ~ 3If the record of entered PLU code is not in PLU file at this program-ming, it will be created in PLU file.

[JOB#2219]PLU CODE DEFINITION FOR DIRECT PLU KEYS

ABCDEF: PLU code = 1~999999

PLU code is assigned to the key No. which has been programmed inJOB#951 programming.

[JOB#2220]LINKED PLU PROGRAMMING

XXXXXX: PLU code = 1 ∼ 999999YYYYYY: PLU code = 1 ∼ 999999

When the "ST" key is pressed without entering any number as thefirst PLU code (YYYYYY), the previous data is cleared.

PLU code should already be defined when they are used in program-ming here.

MRS = 0

[JOB#2221]SET PLU PROGRAMMING

XXXXXX: PLU code = 1 ∼ 999999YYYYYY: PLU code = 1 ∼ 999999

When the "SBTL" key is pressed without entering any number as thefirst PLU code (YYYYYY), the previous data is cleared.

The PLU code (XXXXXX) can not be set the set PLU code(YYYYYY).

PLU code must already be defined when it is used in programminghere.

MRS = 0

2211 XXXXXXPLU code

CL

ABCDEF

No change

For the next PLU

TLST

2214 XXXXXXPLU code

CL

Character key

For the next PLU

No change

TLST

2215 AXXXXXX

No change

PLU code

For next codeCL

ST TL

2219 ABCDEFXXX

Next code

Key No.

0

PLU code

L3

L1

L2

ST TL

2220 YYYYYYXXXXXX

Max. 5 times

0

PLU CODETLST

2221 YYYYYYXXXXXX

Max. 10 times

0

PLU codeTLST

– 24 –

[JOB#2230]PLU CODE PROGRAMMING (range)

XXXXXX: Start PLU code = 1 ∼ 999999YYYYYY: End PLU code = 1 ∼ 999999

AB: Dept. code = 1~50

* All are set with the contents of Start PLU setting.

[JOB#2231]PLU function programming (RANGE)

* All are set with the contents of Start PLU setting.XXXXXX: Start PLU code = 1~999999YYYYYY: End PLU code = 1~999999

A, B: Not used (Fixed at "00")

C: Amount entry type C

Inhibited 0

Open 1

Preset 2

Open and preset 3

Delete 4


MRS = 000

[JOB#2232]PLU TAX STATUS PROGRAMMING (RANGE)

* All are set with the contents of Start PLU setting.XXXXXX: Start PLU code = 1 ∼ 999999YYYYYY: End PLU code = 1 ∼ 999999

A: Sign A

+ 0

– 1

B: Not used (Fixed at "0")

C: VAT 1 C

Non taxable 0

Taxable 1

D: Taxable 3 D

Non taxable 0

Taxable 1

E: Taxable 2 E

Non taxable 0

Taxable 1

F: Taxable 1 F

Non taxable 0

Taxable 1

[JOB#2235]Commission group programming (RANGE)

* All are set with the contents of start PLU setting.XXXXXX: Start PLU code = 1~999999YYYYYY: End PLU code = 1~999999

A: Group No. = 0~3

2230 YYYYYYXXXXXX

PLU CODE

AB

No change ∗

PLU CODE

TLST

2231 XXXXXXPLU CODE

ABC

No change ∗ST TL

CL

YYYYYY

2232 XXXXXX

PLU CODE

ABCDEF

No change ∗

YYYYYY

ST TL

2235 YYYYYYXXXXXX

PLU CODE

A

No change ∗TLST

– 25 –

[JOB#1310]RATE PROGRAMMING

XXX: Fanction No.YYYY. YYYY: Rate

FunctionNo.

Function Entry range Remarks

1 (–)1

0 to 9999.99 (–) unit price 2 (–)2

3 (–)3

4 (–)4

5 %1

0 to 100.00 % rate 6 %2

7 %3

8 %4

51 Exchange 10 to 9999.9999 Rate 52 Exchange 2

53 Exchange 3

63 Commission 10 to 999.99 Rate 64 Commission 2

65 Commission 3

MRS = 0

[JOB#2311]MISC KEY PROGRAMMING 1

XXX: Function No.

Function No. Function

1 (–)1

2 (–)2

3 (–)3

4 (–)4

5 %1

6 %2

7 %3

8 %4

A: Sign A

+ 0

– 1

B, C, D, E, F: Not used (Fixed at "00000")

MRS = 100000

[JOB#2312, 2322]HALO PROGRAMMING

XXX: Function No.A: Mantissa (0 to 9)B: Exponent (0 to 8)

JOB#Function

No.Function Remarks

2312

1 (–)1Item B is specificablewithin the range from 0 to7.

2 (–)2

3 (–)3

4 (–)4

36 RAItem B is specificablewithin the range from 0 to8.

37 RA2

38 PO

39 PO2

2322

41 CA1

Item B is specificablewithin the range from 0 to8.

42 CA2

43 CH1

44 CH2

45 CH3

46 CH4

47 CR1

48 CR2

49 CR3

50 CR4

Entry range, system: A × 10B

MRS = 17 ((–)1~(–)4)18 (Others)

[JOB#2313]MISCELLANEOUS KEY PROGRAMMING (% HALO)

XXX: Function No.YYY. YY: % HALO

FunctionNo.

Function Remarks

5 %1

6 %2

7 %3

8 %4

1310 YYYY.YYYYXXX

Function No. Rate

No change

TLST

2311 ABCDEFXXX

Function No.

No change

TLST

23122322

ABXXX

Function code

No change

ST TL

2313 YYY.YYXXX

No change

TLST

– 26 –

[JOB#2314]TEXT PROGRAMMING FOR MISC KEYS

XXX: FUNCTION CODE

Characters can be entered by using character keys or numeric keys.the key entery sequence for entering one character by numeric keysis as follows:

XXX → 00 key XXX: CHARACTER CODE (3DIGITS)

Please refer to section 3

F-NO. FUNCTION DEFAULT TEXT

1 (–)1 [~]é

2 (–)2 [~]â

3 (–)3 [~]ä

4 (–)4 [~]à

5 %1 ‰é

6 %2 ‰â

7 %3 ‰ä

8 %4 ‰à

9 SET PLU (–) set plu-

10 DIFFER differ

11 TAXABLE1 ST tax1 st



14 TAXABLE ST tax st

15 VAT/TAX 1 vat 1

16 VAT/TAX 2 vat 2

17 VAT/TAX 3 vat 3

18 VAT/TAX vat

19 NET1 NETé

20 NET2 NETâ

21 COUPON PLU cp plu

22 REFUND refund

23 VOID "

24 VOID MODE " mode

25 MANAGER VOID mgr "

26 SBTL VOID sbtl "

27 HASH VOID hash "

28 HASH REFUND hash rf

29 VAT SHIFT vat sft

30 VAT/TAX DELETE tax dele

31 VP COUNTER vp cnt

32 NO SALE no sale

33 G.C. COUNTER g. c. cnt

34

35

36 RA ***ra

37 RA2 ***ra2

38 PO ***po

39 PO2 ***po2


40 CHECK CASHING ca/chk

41 CASH C ash

42 CASH2 C ash2

43 CHECK1 check

44 CHECK2 check2

45 CHECK3 check3

46 CHECK4 check4

47 CREDIT1 credit1

48 CREDIT2 credit2

49 CREDIT3 credit3

50 CREDIT4 credit4

51 EXCHANGE1 exch1

52 EXCHANGE2 exch2

53 EXCHANGE3 exch3

54 EXCHANGE4 exch4

55 EXCHANGE1 IS exch1 is



58 CASH IN DRAWER ****cid

59 CASH/CHECK IS ca/ch is

60 CASH/CHECK IN DRAWER ca/ch id

61 CHECK CHANGE chk/cg

62 GUEST guest

63 COMMISSION SALE1 com.sal1



66 NON COMMISSION SALE non com.

67 ORDER TOTAL order tl

68 PAID TOTAL paid tl

69 DOMESTIC CURRENCY1 dom.cur1




73 CHECK IN DRAWER *ch id

74 (+) DEPT TOTAL *dept tl

75 (–) DEPT TOTAL dept(-)

76 HASH (+) DPT TOTAL *hash tl

77 HASH (–) DPT TOTAL hash(-)

78 BOTTLE (+) TOTAL *bttl tl

79 BOTTLE (–) TOTAL bttl(-)

80 NET 1 (TAXABLE-VAT1) net 1



83 NET (TAXABLE-VAT) net

84 SUBTOTAL subtotal

85 MDS SBTL mdse st

86 TOTAL ***total

87 CHANGE change

88 DUE due

89 ITEMS items

90 PLU ST plu st

2314 Character keyXXX

Function number Max. 8 char.

No change

TLST

– 27 –


91 COPY RCPT TITLE COPY

92 G.C. COPY TITLE g.c. copy

93 AVERAGE ave.

94 GROUP1 Group01

95 GROUP2 Group02

96 GROUP3 Group03

97 GROUP4 Group04

98 GROUP5 Group05

99 GROUP6 Group06

100 GROUP7 Group07

101 GROUP8 Group08

102 GROUP9 Group09

103 CCD CCD

104 CCD DIFFER ccd dif.

105 CCD DIFFER TOTAL dif. tl

106 ORDER TL-PAID TL O ~ P

107 COMMISSION AMOUNT1 com. amt1



110 COMMISSION AMOUNT TTL com. ttl

111 DEPT. REPO. TITLE DEPT

112 GROUP REPO. TITLE group

113 PLU REPO. TITLE PLU

114 STOCK REPO. TITLE stock

115 TRANS. REPO. TITLE trans.

116 CID REPO. TITLE tl-id

117 COM. SALES REPO. TITLE sales

118 CASHIER REPO. TITLE cashier

119 HOURLY REPO. TITLE hourly

120 DAILY NET REPO. TITLE daily

121 SET PLU TITLE set plu

122 TOTAL TAX ttl tax

123 NET WITHOUT TAX NET

124 ZERO SALES REPRT TITLE zero sal

125 CATEGORY REPO. TITLE category

126 DIFFER SUBTOTAL diff st

[JOB#2315]MISC KEY PROGRAMMING (%)

XXX: Function No.

A: % type ASubtotal % 0Item % 1

Function No. Function Remarks5 %16 %27 %38 %4

MRS = 0

[JOB#2316]MISC KEY PROGRAMMING ($ )

XXX: Function No.

A: $ type A

Subtotal $ 0

Item $ 1

Function No. Function Remarks

1 (—) 1

2 (—) 2

3 (—) 3

4 (—) 4

MRS = 0

[JOB#2320]MEDIA KEY PROGRAMMING

XXX: Function No.

FunctionNo.

Function A B C D E F G H I J K

41 CA1 É F F F F — — — — F F

42 CA2 É F F F F — — — — F F

43 CH1 F F F F F — — — — F F

44 CH2 F F F F F — — — — F F

45 CH3 F F F F F — — — — F F

46 CH4 F F F F F — — — — F F

47 CR1 F F F F F — — — — F F

48 CR2 F F F F F — — — — F F

49 CR3 F F F F F — — — — F F

50 CR4 F F F F F — — — — F F

* Items marked with on (F ) are programmable.

A: EFT function A

Non compulsory 0

Compulsory 1

B: Footer print B

No 0

Yes 1

C: Non-add code entry C

Non compulsory 0

Compulsory 1

D: Change due D

Enable 0

Disable 1

E: VP E

Non compulsory 0

Compulsory 1

F, G, H, I: Not used (Fixed at "0000")

2315 XXX A

No change

ST TL

2316 XXX A

No change

ST TL

2320 XXX ABCDEFGHIJK

No change

ST TL

– 28 –

J: Drawer opening J

Yes 0

No 1

K: Entry of amount tended K

Non compulsory (Cash, Check)Inhibit (CR1 to CR8)

0

Compulsory 1

MRS=00000000000

[JOB#2321]MEDIA KEY FUNCTION PROGRAM (AMOUNT HALO)

XXX: Function No.YYYYYYYYY: Limitation amount

Func. No.

Function Entry range MRS

586140

CID (Sentinel)CHK CHANGECA/CHK

0 to 9999999.990 to 999999.990 to 999999.99

9999999.99 999999.99 999999.99

[JOB#1500]CASHIER CODE DIFINITION

XXX: Cashier No.= 1 ∼ 15YYYY: Cashier code = 00 ∼ 99

MRS = 01;1, 02;2, 03;3, 04;4, 05;5, 06;6 ~ 15;15

[JOB#1514]CASHIER NAME PROGRAMMING

YYYY: Cashier code = 01 ∼ 99Characters can be entered by using character keys or numeric keys.The key entry sequence for entering one character by numeric keysis as follows: XXX → 00 KEY XXX: Character code (3 digits)Please refer to section 3.Max. 8 charactersMrs = ’Space’

[JOB#2510]CASHIER PROGRAMMING

YY: Cashier code = 01~99

A: G.C. copy A

Enable 0

Disable 1

B: VAT shift B

Not 0

State 1

C, D: Not used (Fixed at "00")

E: Drawer No. E

Not open 0

Drawer No. 1~2

MRS = 1

[JOB#2610]DATE SETTING

XXYYZZ: Date (Year-Month-Day/Day-Month-Year/Month-Day-Year)

* The date entry format complies with the applicable SRV-modeprogramming.

MRS = 010100

[JOB#2611]TIME SETTING

XX: Hour (00 ∼ 23)YY: Minute (00 ∼ 59)

MRS = 0

[JOB#2612]MACHINE NUMBER SETTING

XXXXXX: Machine number (0 ∼ 999999)

MRS = 0

[JOB#2613]CONSECUTIVE NUMBER SETTING

XXXX: Consecutive number (0000 ∼ 9999)

MRS = 0000

2321 XXX YYYYYYYY

No change

ST TL

1500 XX YY

No change

ST TL

1514 YY Character key

No change

TLST

2510 YY ABCDE

No change

ST TL

2610 XXYYZZ TL

0

2611 XXYY TL

0

2612 XXXXXX TL

0

2613 @/FOR CA/ATXXXX

– 29 –

[JOB#2614]LOGO TEXT PROGRAMMING

X: 1 ∼ 6 1 (24 char.)

2 (24 char.)

3 (24 char.)

4 (24 char.)

5 (24 char.)

6 (24 char.)

Character can be entered by using character keys or numeric keys.The key entry sequence for entering one character by numeric keysis as follows:

XXX → 00 Key XXX: Character code (3 digits)Please refer to section 3.

ER-A460 ER-A470

MRS = S H A R P presents the E R ~ A à ç ü S H A R P I S T H E B E S T

S H A R P presents the E R ~ A à ê ü S H A R P I S T H E B E S T

NOTE: This programming is related to JOB# 912D programming.Only when "6-line header instead of a stamp" is selected byJOB# 912D programming, all 6 lines are programmable.When "3-line header" is selected, upper 3 lines (1st-3rd line)are programmable.When "3-line footer" is selected, lower 3 lines (4th-6th line)are programmable.

[JOB#2615]Programming of the limits to TRY ST feed line and No. of times ofvalidation printing.

Y: No. of times of validation printing = 0 ∼ 9 X: Feed line after depression

of differ ST key. = 0 ∼ 9

MRS = 10

[JOB#2616]OPTIONAL FEATURE

X: 1 MRS = 00000000

A: OP X/Z report A

Enable 0

Disable 1

B: PO operation in REG mode B

Enable 0

Disable 1

C: Not used (Fixed at "0")

D: "RFND" key entry in REG mode D

Enable 0

Disable 1

E: Direct void function in REG mode E

Enable 0

Disable 1

F: Indirect void in REG mode F

Enable 0

Disable 1

G: Subtotal void in REG mode G

Enable 0

Disable 1

H: Refund VP H

Non compulsory 0

Compulsory 1

2614 Character keyX

Position code

No change

ST TL

2615 YX

0

TL

2616 ABCDEFGH

0

X ST TL

– 30 –

X: 2 MRS = 00000000

A: The first last item void A

Enable 0

Disable 1

B: PLU level shift system B

Auto 0

Manual 1

C: PLU level shift system C

MGR & REG mode 0

MGR mode 1

D: Printing of the number of purchases D

No 0

Yes 1

E: Time print E

Yes 0

No 1

F: Printing of journal F

Full print 0

Journal select 1

G: Item VP G

Enable 0

Disable 1

H: (–) VP H

Non compulsory 0

Compulsory 1

X: 3 MRS = 00000000A, B: Not used (Fixed at "00")

C: Zero skip in Cashier report C

Yes 0

No 1

D: Zero skip in Transaction report D

Yes 0

No 1

E: Zero skip in Dept. report E

Yes 0

No 1

F: Zero skip in PLU report F

Yes 0

No 1

G: Zero skip in Hourly report G

Yes 0

No 1

H: Zero skip in Daily net report H

Yes 0

No 1

X: 4 MRS = 00000000A, B: Not used (Fixed at "00")

C: Vat/Tax amount printing on R/J C

Yes 0

No 1

D: Taxable amount printing on R/J D

Yes 0

No 1

E: Net amount printing on R/J E

Yes 0

No 1

F, G: Not used (Fixed at "00")

H: When PLU level system is "Auto" (X:2 B = 0), PLUlevel returns method

H

By one item 0

By one receipt 1

X: 5 MRS = 00000000A, B, C: Not used (Fixed at "000")

D: VAT shift system D

By cashier 0

By shift key 1

E, F, G, H: Not used (Fixed at "0000")

X: 6 NOT USED MRS = 00000000

X: 7 NOT USED MRS = 00000000

X: 8 NOT USED MRS = 00000000

X: 9 NOT USED MRS = 00000000

X: 10 NOT USED MRS = 00000000

X: 11 NOT USED MRS = 00000000

X: 12 NOT USED MRS = 00000000

X: 13 MRS = 00000000

A: Credit totalizer update if RA/PO finalized by Creditkey

A

No 0

Yes 1

B: Separator line in report B

1 line 0

Separator line 1

C, D, E, F, G, H: Not used (Fixed at "000000")

[JOB#2617]PROGRAMMING OF THE TIME INTERVAL FOR THE DRAWERALARM

XXX: 0 ∼ 255 sec

MRS = 000

2617 XXX

0

TL

– 31 –

[JOB#2619]HOURLY REPORT (Starting time)

a: Memory format A

30 minutes (24 hour) 0

15 minutes (12 hour) 1

bb: Starting time (hour): 00 ∼ 23

ex) Case 1.

X1 Hourly report (#160) (15 min, start time = 7]

#160 7:00 (data) 7:15 (data) 7:30

12 hour started from 7:00

(data)

7:45 (data) subtotal (data)

| |

18:45 (data) subtotal (data) **:** (data) Data out of range (19:00 to 6:59)

[JOB#2620]STACK REPORT

XX: JOB#SSSSSS: Start codeEEEEEE: End code

JOB# REPORT NAME TYPE

00 General

10 DEPT./GROUP

13 DEPT. All group

20 PLU RANGE

24 PLU stock RANGE

27 PLU zero sales

29 PLU price category RANGE

30 Transaction

31 CID

32 Commission sale

50 All cashier

60 Hourly RANGE (only X report)

70 Daily net

[** ]Max. 70 step are programmable. "1 step" means the memory sizeused for one no range type JOB#.The RANGE type JOB# means "8 steps".

For example)The memory size for programming JOB#00, 20 and 50 is 10 steps.(ie. 1 step for JOB#00, 8 step for JOB#20, and 1 step for JOB#50. )

[JOB#2630, 2631, 2632]SECRET CODE PROGRAMMING

#2630: PGM1 mode#2631: X1/Z1 mode#2632: X2/Z2 mode

* If "0" is entered, "compulsory secret code entry" is canceled.

MRS = 0

2619 abb

0

TL

2619 107 TL

2620

XX SSSSSS EEEEEE

All delete

No range

Next JOB# (max.=20)

ST TL

2630,2631,2632 XXYY

0

TL

– 32 –

[JOB#2641]MESSAGE TEXT PROGRAMMING

X: Message No. = 1~87

Message No.

Description MRS

1 Registration error ENTRY ERROR

2 Misoperation error MISOPERATION

3Desired code is notprogrammed yet.

NO RECORD

4 Paper empty PAPER EMPTY

5 Secret code error SECRET CODE

6 (reserved)

7 Memory is full MEMORY FULL

8 (reserved)

9 (reserved)

10 Stock is empty OUT OF STOCK

11Compulsory of pushing the STkey

SBTL COMPUL.

12 Compulsory of tendering TEND COMPUL.

13 (reserved)

14 (reserved)

15 (reserved)

16 (reserved)

17 (reserved)

18 (reserved)

19 (reserved)

20 (reserved)

21 (reserved)

22 Cashier changing error CASHIER ERR.

23 Cashier entry error ENTRY ERR CA

24 (reserved)

25 (reserved)

26 (reserved)

27 (reserved)

28 (reserved)

29 (reserved)

30 (reserved)

31Compulsory of non-add codeentry

# COMPULSORY

32The cashier key is not pushedor inserted.

NOT ASSIGNED

33The clerk key is changed in thetransaction

NOT CHANGE

34 Overflow limitation OVER LIMIT.

35 The open price entry is inhibited. INH. OPEN PR

36 The unit price entry is inhibited. INH. UNIT PR

37The direct non-tenderingfinalization after previous tenderentry is inhibited.

NOT NON-TEND

38Service interruption duringValidation printing

P.OFF. IN VP

39 (reserved)

40 (reserved)

41 (reserved)

42 (reserved)

Message No.

Description MRS

43 (reserved)

44 (reserved)

45 (reserved)

46 (reserved)

47 (reserved)

48 (reserved)

49 (reserved)

50 (reserved)

51 (reserved)

52 (reserved)

53 (reserved)

54 (reserved)

55 (reserved)

56 (reserved)

57 (reserved)

58 (reserved)

59 (reserved)

60 (reserved)

61 (reserved)

62 (reserved)

63 (reserved)

64 (reserved)

65 (reserved)

66 (reserved)

67 REG Buffer full BUFFER FULL

68 (reserved)

69 (reserved)

70 (reserved)

71 (reserved)

72 EFT ERROR EFT ERROR

73 EFT BREAK EFT BREAK

74 (reserved)

75 (reserved)

76 Closed drawer error CLOSE DRAWER

77 (reserved)

78 (reserved)

79 (reserved)

80 (reserved)

81 Enter secret code ENTR SECRET#

82 IR sending SEND

83 IR receiving RECEIVE

84 IR send success SEND OK

85 IR reserve success RECEIVE OK

86 IR communication error COM. ERROR

87 IR data format error DATA ERROR

88 IR time out error TIME OUT

89 IR (zaurus) cancel CANCEL

Amessage is 12 characters

Characters can be entered by using character keys or numeric keys.the key entery sequence for entering one character by numeric keysis as follows:XXX → 00 key XXX: Character code (3 digits)Please refer to section 3

Important Note: Change of Message text under this programmingrequires installation of optional ER-01/02 RA RAMchip and creation of File Group No. 16.

2641 Character keyXX

Message No.

No change

ST TL

– 33 –

[JOB#2644]GUIDANCE TEXT PROGRAMMING FOR EASY PROGRAMMING

XX: Guidance No. = 1~132

Characters can be entered by using character keys or numeric keys.the key entery sequence for entering one character by numeric keysis as follows:XXX → 00 key XXX: Character code (3 digits)Please refer to section 3

1 text max. 12 characters

No. MRS JOB No.

1 DEPT PRICE #1110

2 DEPT FUNC. #2110

3 DEPT TAXABLE #2111

4 DEPT HALO #2112

5 DEPT TEXT #2114

6 DEPT COM. GRP #2115

7 DEPT GROUP #2116

8 DEPT DRCTKEY #2119

9 PLU ASG.DEPT #1200

10 PLU PRICE #1210

11 PLU BASE QTY #1211

12 PLU STCK ADD #1220

13 PLU STCK SUB #1221

14 PLU STCK OVW #1222

15 PLU FUNCTION #2210

16 PLU TAXABLE #2211

17 PLU TEXT #2214

18 PLU COM. GRP #2215

19 PLU DRCT KEY #2219

20 LINK PLU #2220

21 SET PLU #2221

22 PLU CODE RNG #2230

23 PLU FUNC RNG #2231

24 PLU STTS RNG #2232

25 PLU COM RNG #2235

26 RATE PRGRAM #1310

27 MISC KEY PGM #2311

28 FNC KEY HALO #2312

29 MDIAKEY HALO #2322

30 % HALO #2313

31 FUNC TEXT #2314



34 MDIA KEY PGM #2320

35 MDIAKEY HALO #2321

36 CSR CODE PGM #1500

37 CSR NAME PGM #1514

38 CSR PGM #2510

39 DATE PROGRAM #2610

40 TIME PROGRAM #2611

41 MCHN NO. PGM #2612

42 CC NO. PGM #2613

43 LOGOTEXT PGM #2614

44 VP,TRY FEED #2615

45 OPT FEATURE #2616

No. MRS JOB No.

46 DRAWER ALERM #2617

47 HOURLYREPORT #2619

48 STACK REPORT #2620

49 SECRET(TEXT) #2630

50 SECRET(X1Z1) #2631

51 SECRET(X2Z2) #2632

52 MESSGE TEXT #2641

53 GUID TEXT #2644

54 TAX RATE #2711

55 PRICE #1110/#1210

56 ENTER DEPT# #1200/#2230

57 SIGN (–) #2111-A/#2211-A/#2311-A

58 SIGN (+) #2232-A

59 TAXABLE1: YES #2111-F/#2211-F/#2311-F

60 TAXABLE1: NO #2232-F

61 TAXABLE2: YES #2111-E/#2211-E/#2311-E

62 TAXABLE2: NO #2232-E

63 TAXABLE3: YES #2111-D/#2211-D/#2311-D

64 TAXABLE3: NO #2232-D

65 VAT: YES

66 VAT: NO

67 PRT CSR: YES #2110-A

68 PRT CSR: NO

69 VP COMPL: YES #2110-B/#2320-E

70 VP COMPL: NO

71 SIF #2110-E

72 SICS

73 NORMAL

74 DELETE #2210-C

75 OPEN&PREST #2110-G/#2231-C

76 PRESET

77 OPEN

78 INHIBITED

79 HALO(EXP.) #2112/#2312/#2322

80 HALO(AMOUNT) #2321

81 HALO(RATE) #2313

82 COM. GRP #2115/#2215/#2235

83 GROUP #2116

84 BASE Q’TY #2118

85 STOCK(ADD) #1220

86 STOCK(SUB) #1221

87 STOCK(OVER) #1222

88 RATE #1310

89 ITEM #2315

90 ST #2316

91 EFT CMPL #2320-A

92 EFT NONCMPL

93 FOOTER: YES #2320-B

94 FOOTER: NO

95 # CMPL #2320-C

96 # NONCMPL

97 DUE DISABLE #2320-D

98 DUE ENABLE

99 DRW OPEN: YES #2320-J

100 DRW OPEN: NO

101 TND CMPL: YES #2320-K

102 TND CMPL: NO

103 TND INH.

2644 Character keyXX

Guidance No.

No change

ST TL

– 34 –

No. MRS JOB No.

104 ENTER PLU# #2220/#2221

105 ENT.CSR CODE #1500

106 ENT.CSR NO

107 ENT.DRW# #2510

108 G.C. COPY: YES

109 G.C. COPY: NO

110 VAT SFT STAT

111 VAT SFT NOT

112 ENT.DEPT# #1110/#2110/#2111/#2112/#2114/#2116

113 ENT.KEY# #2119/#2219

114 ENT.FUNC# #1310/#2311/#2312/#2322/#2313/#2314/#2315/#2316/#2320/#2321

115 #2320/#2321

116 ENT.POS.CODE #2614

117 ENTER TAX NO #2710/#2711

118 ENT.TAX RATE

119 LOWER TAX

120 ENTER MSG NO #2641

121(FIXED DATA) The message for "Fixed"

or "Not used" data

122ENTER [00] KEY For changing character

key layout.

123 PC-LINK SEND #0996

124 PC-LINK RCV. #0998

125 ZAURUS RCV. #1996

126 ONL T. NO. #6110

127 ONL MODEM #6111

128 ONL BAUDRATE #6112

129 ONL CODE #6113

130 ONL TIMER #6114

Important Note: Change of Guidance text under this programmingrequires installation of optional ER-01/02 RA RAMchip and creation of File Group No. 17.

[JOB#2711]TAX RATE PROGRAMMING

* DEPRESSION OF THE ST KEY AT FOLLOWING POINTS PER-FORM A TAX TABLE DELETE OPERATION.

A: Tax programming A

Tax1 1

Tax2 2

Tax3 3

Y: Sign y

+ 0

– 1

xxx.xxxx: Rate = 0.0000~100.0000%LOWER TAX LIMITATION max. 999.99(This is invalid in VAT system.)

MRS = 0

2711 YXXX.XXXXA

Declaration of TAX TAX rate

XXXXX

Lower tax limitfor add tax.

When lower taxlimit is 0.

0

0

TL

TL

– 35 –

[JOB#2900]

<CAUTION>(This JOB must be performed at X2/Z2 mode position.)

AUTO KEY SETTING

(Auto key function)

• This machine has [AUTO] key which can be programmed by thefollowing key-sequence.

• When [AUTO] key is depressed, the machine works the same asthe programmed key-sequence programed.

<Example>Mode switch ⇓(X2/Z2)

(REG)

(X2/Z2)

(REG)

2900 (Free key)AUTO

Max.25

TL

AUTO2

AUTO3

AUTO4

AUTO5

AUTO

AUTO2

AUTO3

AUTO4

AUTO5

Delete

2900 AUTO PLU1 100 DEPT2 AUTO TL

Key entry R/J Display Comment

AUTO PL000001 * 1.10

DEPT02 * 1.00

PL0000001 same as entryPLU11.10

1

10

100

DEPT02 1.10

same as entry1

same as entry0

same as entry0

same as entryDEPT2

2900 AUTO2 PLU1 100 DEPT2 AUTO2 TL

Key entry R/J Display Comment

DEPT 1 DEPT01 DEPT01 1.10

100

CHANGE 0.00

same as entry1

same as entry0

same as entry0

same as entryTL

AUTO 2

* 1.00

*** TOTAL * 1.00

CASH * 1.00

CHANGE * 0.00

10

1

– 36 –

3. Character assignment method

The ER-A460/A470 has two kinds of method at character assign-ment.One is to use alphabetic assigned key and other one is to use tenkeys one is to use ER-01RK.

∼ Using alphabetic assignment method ∼Push alphabetic

Repeat

TL

Programming key layout

1 ER-A460

2 ER-A470

* When the ‘SHIFT’ key is depressed, this character can be preset with small character.

(SHIFT)

1 2 3

4 5 6

7 8 9

0

$BACK

SPACE

(SPACE)

(DC) A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

S

T

U

V

W

X

Y

Z

ST

TL

(SHIFT) (DC) ST

1 2 3

4 5 6

7 8 9

0 00

CL

(DEL)

( ) ( )BACK

SPACE

><

Pt

1 2 3 4 5 6 7 8 9 0

@! # $ ^ & ( )%

?

[ ]!!?

G H

I

J K L

MN

O PQ R

S

T U

V

W

X

Y

Z

A

B

E

D F

C

(SPACE) (SPACE) (SPACE) (SPACE) (SPACE) = - +

;:

/

000 TL

!

ß

§

¤

ØÆ

Ç

£

Ω

Ψ

Υ

Π

Λ

∆Γ

Θ

≡

Σ

Φ

.,

– 37 –

3 ER-01RK * Ten Key/CL key input by remote control key

Ten key function is set to the remote control key for use other thantext input.Keys to be used and their corresponding keys on the ECR

Keys on the remote control Key on the ECR

0, 1 ∼ 9 0, 1 ∼ 9

[00] [00]

(←) [X], [@/FOR]

(→) [ . ]

[ . ] [ . ]

[ST] [SBTL]

[CL] [CL]

If a remote control key other than the above is pressed in a caseother than character input, it is invalid. (the key input is not ac-cepted.)

[TL] key is not provided on the remote control. (After completion ofsetting, press [TL] key on the ECR.)

The remote control keys can be used only in PGM1/PGM2 modes.

For the remote control key layout, refer to the separate sheet.

* The following key marks show the following functions:

Used as:

Keys Normal mode Character entry mode

& key Left cursor key

. key Right cursor key

(BS) — Back space key

(CL) Clear key Clear key

1 !

Numeric key

Numeric key

2 @

3 #

4 $

5 %

6 +

7 &

8 *

9 (

0 )

(SPC) / —A space key or thecharacter key("/")

(00) It used to go into thecharacter entry mode.

—

(SML) —used for entering lettersin lower case.

(SHIFT) —used for entering theright side letter.

(DC) —

used for enteringcharacters in doublesize.

(ST) ) key used for kimination afterone item programming

(BS) (CL)( )

1 2 3 4 $#@!

5 6 7 8 *&+%

9 0 )( - ? =

?

A B C [ ]D

E F G H

( )

I J K L

M N O P

Q R S T

U V W X

Y Z

£ ¢ ß Ç

Pt

!§ !!

( ) ( ) Æ ( ) ( )Ø

; :( ) ( ) ( ) ( )

/ (00)

(ST)(DC)(SHIFT)(SML)

ER-01RK

X

(SPC)

@( )×

( )·

– 38 –

* General instructions for programming alphanumeric charactersusing the ER-01RK

This programming remote keyboard allows you to program variousitems instead of using the keyboard of the cash register.The basic instruction for programming with the remote keyboard isthe same as the one with the keyboard of the register. In this part,the method for programming alphanumeric characters is de-scribed.

Note: Both PGM1 and PGM2 modes are available for this pro-gramming.

Procedure

* 1 Letters of alphabets "A" through "Z" are possible to be enteredin lower case or in upper case. By default, the upper-caseletter mode is selected. To enter the character in lower case,press the (SML) key before you enter the character. TheSML lamp lights up. To return to the upper-case letter mode,press the (SML) key again.

Example: To enter "aA", do the following:

* 2 Characters are possible to be entered in single size or in dou-ble size. By default, the single-size character mode is se-lected. To enter the character in double size, press the (DC) key before you enter the character. The DC lamp lightsup. To return to the single-size character mode, press the (DC) key again.

Example: To enter " ", do the following:

* 3 Each character key has two levels. For example, with the A key, you can enter "A" or "". Under the normal condi-tion, the left side letter is selected. To use the right sideletter, press the (SHIFT) key just before you press a key.

Example: To enter "Aa[", do the following:

* 4 "( )", "( )", "( ~ )", "( )", "( )", "( )", "( )", and "( )" areused only for combination with a character key. If the combina-tion is unavailable, only a character key is entered.

Example: To enter "Ä", do the following:

To enter "ä", do the following:

(SHIFT)(DC)(SML)

To enter the characterin the current case

To enter the characterin the current size

*1 *2 *3

To enter in theleft side letter

One of the ( ), ( ), ( ),( ), ( ), ( ), ( ), ( )keys

*4

To use key combination

A characterkey

To enter next character

A (SML) A (SML)

aAA

(SML) (DC) A (SML) A (DC)A

(SML)A (SHIFT)A C

(SHIFT) ; ( ) A

(SML) (SHIFT) ; ( ) A

– 39 –

4 Using ten key of ECR

Note: 00 key is used to enter each 3 digit alpha code.

00XXX

3 digits

Repeat

TL

CODE TABLE FOR ALPHA DESCRIPTOR PROGRAMMING

CODE CHARACTER

001 á

002 â

003 ê

004 î

005 ì

006 í

007 ô

008 ó

009 û

010 ú

011 œ

012 ü

013 ú

014 ö

015 ó

016 Λ017 Ψ018 Γ019 ⋅⋅

020 Ω021 ∆022 Θ023 Ξ024 Π025 Σ026 ϒ027 Φ028

029 Ú

030

031 Ó

033 !

034 "

035 #

036 $

037 %

038 &

039 ’

040 (

041 )

042 *

043 +

044 ,

CODE CHARACTER

045 –

046 .

047 /

048 0

049 1

050 2

051 3

052 4

053 5

054 6

055 7

056 8

057 9

058 :

059 ;

060 <

061 =

062 >

063 ?

064 @

065 A

066 B

067 C

068 D

069 E

070 F

071 G

072 H

073 I

074 J

075 K

076 L

077 M

078 N

079 O

080 P

081 Q

082 R

083 S

084 T

085 U

086 V

087 W

CODE CHARACTER

088 X

089 Y

090 Z

091 Ä

092 Ö

093 Ü

094 ^

095 _

096 ‘

097 a

098 b

099 c

100 d

101 e

102 f

103 g

104 h

105 i

106 j

107 k

108 l

109 m

110 n

111 o

112 p

113 q

114 r

115 s

116 t

117 u

118 v

119 w

120 x

121 y

122 z

123

124 |

125

126 β127

128 !!

129 1

130 2

CODE CHARACTER

131 3

132 4

133 1⁄2134 FT

135 ←136 →137 Ä

138 \

139 e

140 d

141 F

142 T

143 ↓144 ç

145 o

146 ¿

147 Ù

148 à

149 Æ

150 φ151 Å

152 ¤

153 é

154 è

155 Pt

156 ¡

157 Ñ

158 ò

159 £

177 Á

178 Í

180 A181 a

182 E

183 e

184 I

185 i

186 U

187 u

188

189

192

193

CODE CHARACTER

194

195

196

197

198

199

200

201

203 ‰

204 d−

205 ‡

206 §

208 P

209 ç

210 ë

211 †

212 ç

213 ¡

214 ÿ

215 u•

216 æ

217 ∨

218 å

219 ©

224 *

225 §

226 ∅227 ∧

228 ↑229 ]

230 [

231

232 ä

233 ö

234 ü

235 æ

236 å

237 É

238 ñ

253 DC

U

O

c N,n,c

G

S

G,<g

K,k,L,l,

´

DC: DOUBLE CODEFig. 7-2

– 40 –

CHAPTER 3. OP X/Z, X1/Z1,X2/Z2MODEThe following categories of reports can be printed by the ECR.

1) OP X/Z reports (individual clerk reports)

2) X1/Z1 reports (Daily sales total X and Z reports)

3) X2/Z2 reports (Periodic total X and Z reports)

To print reports, use the following key entry sequence

JOB# Range is required

Reading

Resetting

TL

MODE * 1

OP X/Z X1/Z1 X2/Z2 F-read * 3 DATA FOR

REPORT NAME X Z X1 Z1 X2 Z2 X1 * 4 JOB# READING NOTE

GENERAL F F F F 00 —

DEPT/GROUP F F F 10 —

IND. GROUP F F 12 GROUP No.

GROUP TOTAL F F 13 —

PLU BY RANGE F F F F 20 PLU CODE * 2

PLU BY DEPT F F 21 DPT CODE

PLU STOCK F 24 PLU CODE * 2

PLU ZERO SALES F F 27 ALL

PLU PRICE CATEGORY F F 29 PRICE * 2

TRANSACTION F F 30 —

TL-ID F F 31 — ALL CASHIER

COMMISSION SALES F F 32 —

ALL CASHIER F F F F 50 —

IND. CASHIER F F F F F F 51 —

HOURLY (ALL) F F 60

HOURLY (RANGE) F 60 * 2

DAILY NET F F F 70

STACKED REP F F F F 90

* 1 X1: Daily X report Z1: Daily Z reportX2: Periodic X report Z2: Periodic Z report

Stop of printing reports:The printing of all reports can be stopped by the following operation.

Set the mode switch to "MRG" to cancel.

Note) When the printing is stopped, the consecutive number or Zcounter don’t return to the original value.When Z reports, Memory is not reset.In In-line system, when Master has consolidated the data fromthe satellite, ECR can not stop the printing.

* 1 X1: Daily X reportX2: Periodic X report

Z1: Daily Z reportZ2: Periodic Z report

* 2 PLU code range can be specified by entering the start and endnumbers according to the following procedure. When specifyinga single time interval, PLU code, the start number has only to beentered.

* 3 When 2 is entered in the third digit of a job code, periodic reportsare printed.Example: Daily general report; job code 100

Periodic general report; job code 200* 4 Reading display only

→ KEY → CL (Display amount) (Display initialize)

KEY DEPT = DEPTn keyCID = ⊗ keyDaily Net = ST key

• An individual report is printed on the receipt and journal when theTL key is pressed.

• Pressing the decimal point key just after the enery of a job codeclears the corresponding data in the ECR. (Z report)(When printing those reports for which no Z reports can be taken,the decimal point key cannot be pressed after the entry of a jobcode.)

• When the decimal point key is not pressed after the entry of a jobcode, the corresponding data is held in the ECR. (X report)

XXXX

All

Start No.XXXX

End No.

– 41 –

Documents

MODEL ER-A460 MODEL ER-A470 - Inland Cash … MANUAL CODE: 00ZERA460VPME ELECTRONIC CASH REGISTER MODEL ER-A460 MODEL ER-A470 (For "V" version) SRV KEY : LKGIM7113RCZZ PRINTER : DP-730