-
©2008 A+ Corporation, LLC. All rights
reserved.SCC-33M-InsInstallationOperation_0508An ISO 9001:2000
certified company
Manufacturing Contact InformationA+ Corporation, LLC41041 Black
Bayou Rd.Gonzales, LA 70737
Call for expert product application assistance:Phone:
(225)-644-5255 Website: www.geniefilters.comFax: (225)-644-3975
E-mail: [email protected]
Safety Warnings!
Tools Required
Model 33M
™
Avenger™ Model 33M Installation & Operation Instructions
Failure to abide by any of the safety warnings below may result
in equipment failure and serious injury or death.For models
containing Liquid Block™: Slowly open the supply pressure so that
the minimum differential pressure required to shut-off the Liquid
Block™ is not met or exceeded..Valve off the sample flow before
installation. Do not exceed any equipment pressure ratings.
Four #10 screws for mounting bracket to panel. Screwdriver for
mounting bracket to panel.
-
©2008 A+ Corporation, LLC. All rights reserved.
Model 33M
™
SCC-33M-InsInstallationOperation_0508An ISO 9001:2000 certified
company 2
Technical Specifi cations
DimensionsBack View Side View
3.000”
4.420”
2.875”3.592””
0.544”
4.670”
2.250”
4.670” 4.223”
1.414”
2.000”Dia.
Port D
5.144”
Minimum Maintenance Clearance 8.250”
OPTIONALMOUNTINGBRACKET
Maximum pressure rating 1,000 psigMaximum recommended Lowest
possible pressure consistent with application supply pressure
Maximum temperature 185 °F (85 °C) for Type 5 membrane
302 °F (150 °C) for Hi-Flow Backed membrane
Port sizes Inlet, Outlet, & Bypass: 1/2” female NPTGauge:
1/4” female NPT
Internal volume 200 cc
Wetted materials Machined parts : 316 stainless steel / NACE
compliant All other metal parts: stainless steel / NACE compliant
Sealing material: Viton® standard Membrane: inert
Number of ports 5
Element size
Maximum recommended 4,000 cc/min for Type 5 membrane membrane
flow rate 9,000 cc/min for Hi-Flow Backed membrane
*Maximum flow results in approximately 2 psi
membranedifferential pressure
(For higher flow rates contact the factory)
Outside Diameter: ~ 1.4”Inside Diameter: ~ 1.0”Length: ~
2.5”
Maximum Liquid Block™ 85 psig**Slowly open the supply pressure
so that the minimum differential pressure required to shut-off the
Liquid Block™ is not met or exceeded.
valve auto-reset pressure
-
©2008 A+ Corporation, LLC. All rights reserved.
Model 33M
™
SCC-33M-InsInstallationOperation_0508An ISO 9001:2000 certified
company 3
Installation InstructionsInstall the mounting bracket onto the
Avenger Model 33M or 38M as per the Mounting Bracket Installation
Instructions included in A+ Corporation Mounting Bracket Kit P/N
33-509SS for Model 33M or P/N 38-509SS for Model 38M. Aftermarket
brackets may be mounted as per the mounting diagrams below. Mount
the Avenger horizontally as shown in the diagram. Lock washers may
be used on the lower 10-32 screws to tilt the filter as shown to
ensure that liquids drain properly. “Port D” should be facing down
as shown. An optional downstream pressure gauge may be installed in
“Port E” or it may be plugged. The Model 33M has 1/2” NPT ports
(except for the 1/4” NPT gauge “Port E”) and the Model 38M has 1/4”
NPT ports. Refer to the “Application” for tubing connection
instructions.
Application Drawing
-
©2008 A+ Corporation, LLC. All rights reserved.
Model 33M
™
SCC-33M-InsInstallationOperation_0508An ISO 9001:2000 certified
company 4
Application Drawing
-
Model 33M
™
An ISO 9001:2000 certified company Genie, ® Avenger,TM Liquid
BlockTM and Genie® Membrane TechnologyTM are trademarks or
registered
trademarks of A+ Corporation, LLC. All other referenced
trademarks are the property of their respective owners.
Model Numbering & Additional Part Numbers
!
Your model number is determined by your specific needs. Choose
options below.
Sealing material
Membrane type 5 = Type 5 7 = Hi-Flow Backed
Mounting bracket accessory Part # = 33-509-SS (sold
separately)
How to build the model number:
Sealing materialElement typeMembrane typeLiquid Block™
option
33M 3/2 S How to build the replacement o-ring kit number:
Sealing material
33M 5 0
How to build the replacement membrane kit number:
Membrane type
33M 5 0 How to build the replacement filter element number:
Element type
30 5
Element type 07CFS = 0.1 micron coalescer fluorocarbon SS10 = 10
micron stainless steel
Liquid Block™ Blank = No Liquid Block™ L = Liquid Block™
0 = Viton® 1 = Kalrez® (other materials available upon request)
!
!
We cannot recommend specific sealing materials due to the
complex nature of sample stream compositions. Temperature and
pressure also may be factors. Unless specified otherwise, the
product will ship with our standard sealing materials and materials
of construction stated in the technical specifications section of
the corresponding Product Sheet. Please refer to
www.dupontelastomers.com for sealing material recommendations and
advice. It is the user’s responsibility to specify the sealing
materials and other materials of construction for their
application.
!
! !
