MMPS, MMRSW, MMH, MMW, MMS, MMK, MMT and … MMK, MMT and MMV Series Orbital Motors Technical Information ... Start-up Procedures ... Motor Testing: · Motors tested

www.metaris.com www.orbitalmotors.net

Low Speed High Torque

GENUINE METARISORBITAL MOTORS

MMPS, MMRSW, MMH, MMW,MMS, MMK, MMT and MMV

Series Orbital MotorsTechnical Information

A Hydraulex Global Company

Genuine Metaris Orbital MotorsTechnical Information

2 Hydraulex Global Low Speed High Torque Motors OMLSHT-Rev 07.2014

Series Replacement for: Page

Technical Information ALL 3

MMPS

DH, DS, OMP, OMR SeriesH(101-), S(103-), T(158-) SeriesTB, TC SeriesHB(300), RS(200/201), WD(145/146), WG(275/276/277/278/280/281), WP(155/156), WR(255/256) Series

6

MMRSW

OMEW SeriesW(162-) SeriesTJ, TF, TL SeriesWG(275/276) Series

16

MMH

OMH Series

TG Series

24

MMW

W(162-) SeriesTF, TG SeriesCE(400/401/420/421), HB(300), RE(500/501) Series

32

MMS

OMS Series2000(104-, 105-, 106-) SeriesTE, TF, TG SeriesDR(600/620), HB(300), RE(500/501/520/521), WS (350/351/355/356/357/358) Series

42

MMK

TMT Series4000(109-, 110-, 111-) SeriesTG Series 58

MMT

OMT Series6000(112-, 113-, 114-) SeriesTG, TK SeriesDT(700), D9(800) Series

70

MMV

OMV Series10000(119-) Series

DT(700), D9(800) Series

84

Special Options ALL 97

Spool Valve

Disc Valve

Contents

All measurements are in millimeters (mm) unless otherwise marked.

All manufacturers names, symbols and descriptions in this document are used for reference purposes only, and it is not implied that any parts listed is the product of these manufacturers.


Hydraulex Global Low Speed High Torque Motors OMLSHT-Rev 07.2014 3

Technical Information - All SeriesShaft Seal Specifications/Benefits: · Genuine Metaris Motors incorporate a high pressure shaft seal which allows higher backpressures · Case drain line is recommended when backpressure exceeds individual performance data table · Increases ability to handle high pressure spikesRecommended Fluid Specifications: · Anti-wear hydraulic oil · Viscosity of 172 - 334 SUS (37 - 73 cSt) · Recommended oil cleanliness - ISO4406 = 18/13 · Maximum recommended operating temperature - 80°C (176°F)Pressure and Speed Operation Parameters: · Simultaneous maximum RPM and maximum pressure NOT recommended · Maximum pressure or maximum RPM operation: 10% of every minute · Intermittent pressure is the allowed pressure at the inlet port · Continuous pressure is the working pressure difference between inlet and outlet portsStart-up Procedures (to assure best motor life): · Ensure motor is filled with equipment manufacturers recommended fluids prior to any load application · Operate motor at 30% of rated pressure for at least one hour before application of full load

General

Rotation - Port Plumbing



Technical Information - All SeriesGeneral

Individual Performance Data Graph Information: · Motors run with high efficiency in all areas designed with a number for torque and speed. · However, for best motor life, select a motor to run with a torque and speed range shown in the light gray area (Continuous). · Performance data is typical at 120 SUS (25.2 cSt). · Actual data may vary slightly from unit to unit in production.

Case Drain Information: · All Genuine Metaris Motors will be supplied with a case drain and shipped with a Steel Hex Socket Plug installed Advantages provided by use of a case drain: · Contamination control - flushing the motor case · Cooler operating temperatures - exiting oil draws motor heat away · Extended motor seal life - maintains lower case pressure (Due to the fact of a pre-installed preset restriction valve)

Plumbing Diagrams:



Technical Information - All SeriesGeneral

GeroterFixed Lobes on Ring:· Higher Friction· Lower Mechanical Efficiency· Lower Start-up Torque· Jerky Low Speed Operation· Greater Wear on Lobes = Shorter Life· Lower Price Point

Roller-StarRotating Rollers on Ring:· Lower Friction· Higher Mechanical Efficiency· Higher Start-up Torque· Smooth Low Speed Operation· Less Wear on Rollers = Longer Life· Higher Price Point*(*Metaris offers the Roller-Star version at the Geroter Price Point.)

Motor Testing: · Motors tested prior to painting Tested Cleaned Heated and dried Painted while warm · Test report provided with each unit · High quality standards maintained Volumetric efficiency 85% or higher 10% re-tested by QC Department

Geroter vs Roller-Star: · All Genuine Metaris Orbital Motors incorporate Roller-Star design · Roller-Star technology at Geroter prices · Provides longer operational life



MMPS SeriesGeneral

MMPS series motors are spool valve motors, with the characteristic features of: • Advanced Roller-Star technology, requiring lower pressure at start-up and providing smooth reliable operation at all speeds • High efficiency shaft bearing, which allows higher pressure, speed and radial force • High pressure shaft seal, which allows for higher back pressures and an increased ability to handle high pressure spike conditions • Internal integrated check valve, which limits case pressure by blocking the high pressure port side and allowing the motor housing to drain into the outlet (low pressure) port. Motors connected in series will utilize the case drainThese motors can be used in parallel or series. A diverse offering of mounting flanges, shafts, ports, and displacements allow for easy installation, product replacement, or OEM application.

· Simultaneous maximum torque & maximum speed NOT recommended.· Continuous Rating » (Cont.) motor may be run continuously at these ratings.· Intermittent Operation » (Int.) 10% of every minute.· ∆ - True pressure difference between inlet port and outlet port.· Maximum case pressure without case drain -- 1” Shaft = 125 Bar (1813 psi) | Greater than 1” Shaft 75 Bar (1088 psi).

Description

Specifications Model Code 01 02 03 04 05 06 07 08 09 10 11

Displ.cm³/r 50 63 80 100 125 160 200 250 305 370 395

in³/r 3.1 3.8 4.9 6.1 7.6 9.8 12.2 15.3 18.6 22.6 24.1

Flow

LPMCont. 38 53 53 53 53 53 53 53 53 53 53

Int. 45 57 57 57 57 57 57 57 57 57 57

GPMCont. 10.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0

Int. 11.9 15.1 15.1 15.1 15.1 15.1 15.1 15.1 15.1 15.1 15.1

Max Speed RPM

Cont. 750 778 635 510 430 329 266 213 171 142 133

Int. 875 832 680 537 420 347 281 226 182 150 141

Pressure

∆BarCont. 138 138 138 138 138 124 124 124 103 83 83

Int. 155 155 155 155 155 138 138 127 110 90 90

∆PSICont. 2002 2002 2002 2002 2002 1798 1798 1798 1494 1204 1204

Int. 2248 2248 2248 2248 2248 2002 2002 1842 1595 1305 1305

Torque

NMCont. 93 123 155 196 230 271 328 401 417 402 429

Int. 105 138 174 219 256 297 359 410 441 427 458

LBF-INCont. 823 1089 1372 1735 2036 2399 2903 3549 3691 3558 3797

Int. 929 1221 1540 1938 2266 2629 3177 3629 3903 3779 4054



Genuine Metaris Orbital Motor MMPS

Series

Displacement cm³/r (in³/r) 01 = 50 (3.1)02 = 63 (3.8)03 = 80 (4.9)04 = 100 (6.1)05 = 125 (7.6)06 = 160 (9.8)07 = 200 (12.2)08 = 250 (15.3)09 = 305 (18.6)10 = 370 (22.6)11 = 395 (24.1)

Flange & PilotA = 2-Bolt SAE “A”, pilot Ø82.5 (3.25”) x 8 (.31”)B = 4-Bolt SAE “A”, pilot Ø82.5 (3.25”) x 8 (.31”)C = 2-Bolt SAE “A”, pilot Ø82.5 (3.25”) x 2.8 (.11”)D = 4-Bolt SAE “A”, pilot Ø82.5 (3.25”) x 2.8 (.11”)E = 4-3/8-16 Square-flange, pilot Ø44.4 (1.75”) x 2.8 (.11”)F = 4-M10x1.5 Square-flange, pilot Ø44.4 (1.75”) x 2.8 (.11”)

Model Code

PaintA = No PaintB = Blue (Standard)C = BlackOptions A & C (or any other color needed) will only be considered for Large Quantity Orders

RotationA = Standard (Clock-wise)B = Opposite (Counter Clock-wise)

Drain Port1 = G 1/4 BSP2 = 7/16”-20UNF3 = M14x1.54 = PT(RC) 1/4”5 = M10x1All motors come with a Steel Hex Socket Plugged Drain Port

PortsA = G 1/2, BSPB = 1/2”-14NPTFC = M18x1.5D = 7/8”-14UNF, O-ringE = G 1/2, O-ringF = M22x1.5G = 4-5/16”-18UNC (Manifold)H = 4-M8x1.5 (Manifold)I = PT(RC) 1/2”J = M20x1.5

MMPS - 01 - A - 01 - D - 2 - B - A

Shafts01 = 25mm (.984”) Straight, Flat key 8 x 7 x 3202 = 25.4mm (1”) Straight, Flat key 6.35 x 6.35 x 3203 = 25.4mm (1”) SAE 6B Splined - M8 Tap04 = 32mm (1.26”) Straight, Flat key 10 x 8 x 4505 = 31.75mm (1.25”) Straight, Flat key 7.96 x 7.96 x 3206 = 31.75mm (1.25”) Tapered Shaft, Flat key 7.96 x 7.96 x 3207 = 35mm (1.26”) Tapered Shaft, Flat key 6 x 6 x 2008 = 31.75mm (1.25”) 14t Splined09 = 25.4mm (1”) Straight, Woodruff key10 = 25.4mm (1”) SAE 6B Splined - 1/4” -20 Tap11 = 25.4mm (1”) Straight, with 0.315” dia. crosshole12 = 25.4mm (1”) Straight, with 0.406” dia. crosshole13 = 22.23mm (.875”) Straight14 = 22.23mm (.875”) SAE B Shaft 13t Splined15 = 25mm (.984”) Straight, 8mm keyway16 = 25.4mm (1”) Tapered Shaft, with Woodruff Key and Nut17 = 25.4mm (1”) Straight, with 0.406” dia. crosshole & 6.35 x 6.35 x 32 Flat key



MMPS SeriesMMPSSpecifications

To assure best motor life, run motor for approximately one hour at 30% of rated pressure before applying full load. Fill motor with equipment manufacturer’s recommended fluid prior to any load application and startup.

Side Load

Shaft Seal



Performance DataMMPSSpecifications



Performance DataMMPSSpecifications



MMPSDimensions

Dimensions - Staggered Ports (Flanges A & B)Displ. cm³/r. 50 63 80 100 125 160 200 250 305 370 395

XInches (.35) (.45) (.57) (.71) (.90) (1.14) (1.40) (1.76) (2.21) (2.67) (2.84)

Millimeters 9 11.5 14.44 18.05 22.78 28.88 35.61 44.65 56.03 67.92 72.01

YInches (5.64) (5.74) (5.85) (6.0) (6.19) (6.43) (6.69) (7.04) (7.49) (7.96) (8.12)

Millimeters 143.3 145.8 148.7 152.4 157.1 163.2 170 178.9 190.3 202.2 206.3



MMPSDimensions Dimensions - Aligned Ports (Flanges C, D, E & F)

Displ. cm³/r. 50 63 80 100 125 160 200 250 305 370 395

XInches (.35) (.45) (.57) (.71) (.90) (1.14) (1.40) (1.76) (2.21) (2.67) (2.84)

Millimeters 9 11.5 14.44 18.05 22.78 28.88 35.61 44.65 56.03 67.92 72.01

YInches (5.76) (5.86) (5.97) (6.12) (6.30) (6.54) (6.81) (7.17) (7.61) (8.08) (8.24)

Millimeters 146.3 148.8 151.7 155.4 160.1 166.2 173 182 193.3 205.2 209.3



MMPSFlanges Mounting Flanges

(A) = 2-Bolt SAE “A”, Long Pilot 8mm (.31”)

(C) = 2-Bolt SAE “A”, Pilot 2.8mm (.11”)

(E) = 4-3/8”-16 Square-flange

(B) = 4-Bolt SAE “A”, Long Pilot 8mm (.31”)

(D) = 4-Bolt SAE “A”, Pilot 2.8mm (.11”)

(F) = 4-M10x1.5 Square-flange



MMPSShafts

Shafts



MMPSShafts

Shafts



MMRSW SeriesGeneral

MMRSW series wheel motors are spool valve motors, with the characteristic features of: • Compact and light weight design • Advanced Roller-Star technology, requiring lower pressure at start-up and providing smooth reliable operation at all speeds • Dual high efficiency tapered roller bearings, providing excellent low speed and high speed operation with high side load capabilities • High pressure shaft seal, which allows for higher back pressures and an increased ability to handle high pressure spike conditions • Internal integrated check valve, which limits case pressure by blocking the high pressure port side and allowing the motor housing to drain into the outlet (low pressure) port. Motors connected in series will utilize the case drainThese motors can be used in parallel or series.

· Simultaneous maximum torque & maximum speed NOT recommended.· Continuous Rating » (Cont.) motor may be run continuously at these ratings.· Intermittent Operation » (Int.) 10% of every minute.· ∆ - True pressure difference between inlet port and outlet port.· Maximum case pressure without case drain -- 75 Bar (1088 psi).

Description

Specifications Model Code 01 02 03 04 05 06 07 08 09 10 11

Displ.cm³/r 50 63 80 100 125 160 200 250 305 370 395

in³/r 3.1 3.8 4.9 6.1 7.6 9.8 12.2 15.3 18.6 22.6 24.1

Flow

LPMCont. 40 50 60 60 60 60 60 60 60 60 60

Int. 50 60 75 75 75 75 75 75 75 75 75

GPMCont. 10.6 13.2 15.9 15.9 15.9 15.9 15.9 15.9 15.9 15.9 15.9

Int. 13.2 15.9 19.8 19.8 19.8 19.8 19.8 19.8 19.8 19.8 19.8

Max Speed RPM

Cont. 775 760 750 600 475 375 300 240 190 160 150

Int. 970 950 940 750 600 470 375 300 240 200 185

Pressure

∆BarCont. 140 140 175 175 175 175 175 175 135 115 115

Int. 175 175 200 200 200 200 200 200 175 150 150

∆PSICont. 2031 2031 2538 2538 2538 2538 2538 2538 1958 1668 1668

Int. 2538 2538 2901 2901 2901 2901 2901 2901 2538 2176 2176

Torque

NMCont. 100 126 195 240 300 380 450 540 550 580 620

Int. 130 163 220 280 340 430 500 610 690 690 735

LBF-INCont. 885 1115 1726 2124 2655 3363 3983 4779 4868 5133 5487

Int. 1151 1443 1947 2478 3009 3806 4425 5399 6107 6107 6505



Genuine Metaris Orbital Motor MMRSW

Series

Displacement cm³/r (in³/r) 01 = 50 (3.1)02 = 63 (3.8)03 = 80 (4.9)04 = 100 (6.1)05 = 125 (7.6)06 = 160 (9.8)07 = 200 (12.2)08 = 250 (15.3)09 = 305 (18.6)10 = 370 (22.6)11 = 395 (24.1)

Flange & PilotA = 4-Bolt Wheel Flange, pilot Ø82.5 (3.25”)

Model Code



Drain Port1 = G 1/4 BSP2 = 7/16”-20UNF, O-ring3 = M14x1.54 = PT(RC) 1/4”5 = M10x1All motors come with a Steel Hex Socket Plugged Drain Port

PortsA = 7/8”-14UNF, O-ringB = G 1/2, BSP

MMRSW - 01 - A - 01 - D - 2 - B - A

Shafts01 = 35mm (1.38”) Tapered02 = 31.75mm (1.25”) Tapered03 = 25.4mm (1”) Tapered Shaft, with Woodruff Key and Nut04 = 31.75mm (1.25”) Straight, Keyed



MMRSW SeriesMMRSWSpecifications


Side Load

Shaft Seal



Performance DataMMRSWSpecifications



Performance DataMMRSWSpecifications



MMRSWDimensions

MMRSWPort Thread

Versions

Dimensions - Aligned PortsDispl. cm³/r. 50 63 80 100 125 160 200 250 305 370 395

XInches (.35) (.45) (.57) (.71) (.90) (1.14) (1.40) (1.76) (2.21) (2.67) (2.84)

Millimeters 9 11.5 14.4 18 22.8 28.8 35.6 44.6 56 68 72

YInches (4.70) (4.80) (4.91) (5.05) (5.24) (5.48) (5.74) (6.10) (6.55) (7.02) (7.18)

Millimeters 119.3 121.8 124.7 128.3 133.1 139.1 145.9 154.9 166.3 178.3 182.3



MMRSWFlanges Mounting Flanges

(A) = 4-Bolt Wheel Flange, Pilot 82.6 (3.25”)



MMRSWShafts

Shafts



MMH SeriesGeneral

MMH series motors are spool valve motors, with the characteristic features of: • Compact and light weight design • Advanced Roller-Star technology, requiring lower pressure at start-up and providing smooth reliable operation at all speeds • Dual needle bearings, providing high side load capacity with extended operating life • High pressure shaft seal, which allows for higher back pressures and an increased ability to handle high pressure spike conditions • Internal integrated check valve, which limits case pressure by blocking the high pressure port side and allowing the motor housing to drain into the outlet (low pressure) port. Motors connected in series will utilize the case drainThese motors can be used in parallel or series. The broad displacement range is a plus in meeting yourpower requirements.


Description

Specifications Model Code 01 02 03 04 05 06 07

Displ.cm³/r 200 245 310 390 490 630 800

in³/r 12.2 15.0 18.9 23.8 29.9 38.4 48.8

Flow

LPMCont. 80 80 80 80 80 80 80

Int. 100 100 100 100 100 100 100

GPMCont. 21.1 21.1 21.1 21.1 21.1 21.1 21.1

Int. 26.4 26.4 26.4 26.4 26.4 26.4 26.4

Max Speed RPM

Cont. 360 320 250 200 156 120 100

Int. 470 390 300 240 200 150 120

Pressure

∆BarCont. 175 175 175 155 125 125 100

Int. 200 200 200 190 150 150 120

∆PSICont. 2538 2538 2538 2248 1813 1813 1450

Int. 2901 2901 2901 2756 2176 2176 1740

Torque

NMCont. 500 614 777 866 877 1128 1146

Int. 573 700 888 1061 1053 1350 1375

LBF-INCont. 4425 5434 6877 7665 7762 9984 10143

Int. 5071 6196 7859 9391 9320 11949 12170



Genuine Metaris Orbital Motor MMH

Series

Displacement cm³/r (in³/r) 01 = 200 (12.2)02 = 245 (15.0)03 = 310 (18.9)04 = 390 (23.8)05 = 490 (29.9)06 = 630 (38.4)07 = 800 (48.8)

Flange & PilotA = 4-Bolt SAE “A” Magneto Flange, pilot Ø82.5 (3.25”)

Model Code



Drain Port1 = G 1/4 BSP2 = M14x1.53 = 7/16”-20UNF, O-ring4 = PT(RC) 1/4”All motors come with a Steel Hex Socket Plugged Drain Port

PortsA = 7/8”-14UNF, O-ringB = 1/2”-14NPTFC = G 1/2, BSPD = 3/4”-16UNF, O-ringE = M18x1.5F = M20x1.5G = M22x1.5H = PT(RC) 1/2”

MMH - 01 - A - 01 - D - 2 - B - A

Shafts01 = 32mm (1.26”) Straight, Flat key 10 x 8 x 4502 = 35mm (1.38”) Straight, Flat key 10 x 8 x 4503 = 31.75mm (1.25”) Straight, Flat key 7.96 x 7.96 x 3204 = 25.4mm (1”) SAE 6B Splined05 = 31.75mm (1.25”) 14t Splined M8 “European Standard”06 = 31.75mm (1.25”) 14t Splined 3/8” - 16 “US Standard”07 = 35mm (1.38”) Tapered Shaft, Flat key 6 x 6 x 20



MMH SeriesMMHSpecifications


Side Load

Shaft Seal



Performance DataMMHSpecifications



Performance DataMMHSpecifications



MMHDimensions

Dimensions - Staggered PortsDispl. cm³/r. 200 245 310 390 490 630 800

XInches (.88) (1.08) (1.36) (1.71) (2.15) (2.73) (3.51)

Millimeters 22.4 27.4 34.6 43.4 54.5 69.24 89.1

YInches (6.77) (6.98) (7.27) (7.61) (8.05) (8.63) (9.41)

Millimeters 172 177.4 184.6 193.4 204.5 219.2 239.1



MMHFlanges Mounting Flanges

(A) = 4-Bolt SAE “A” Magneto Flange, Pilot 82.5 (3.25”)



MMHShafts

Shafts



MMW SeriesGeneral

MMW series wheel motors are spool valve motors, with the characteristic features of: • Compact and light weight design • Advanced Roller-Star technology, requiring lower pressure at start-up and providing smooth reliable operation at all speeds • Dual high efficiency tapered roller bearings, providing excellent low speed and high speed operation with high side load capabilities • High pressure shaft seal, which allows for higher back pressures and an increased ability to handle high pressure spike conditions • Internal integrated check valve, which limits case pressure by blocking the high pressure port side and allowing the motor housing to drain into the outlet (low pressure) port. Motors connected in series will utilize the case drainThese motors can be used in parallel or series. The broad displacement range is a plus in meeting yourpower requirements.


Description


Displ.cm³/r 200 245 310 390 490 630 800

in³/r 12.2 15.0 18.9 23.8 29.9 38.4 48.8

Flow

LPMCont. 80 80 80 80 80 80 80

Int. 100 100 100 100 100 100 100

GPMCont. 21.1 21.1 21.1 21.1 21.1 21.1 21.1

Int. 26.4 26.4 26.4 26.4 26.4 26.4 26.4

Max Speed RPM

Cont. 360 320 250 200 156 120 100

Int. 470 390 300 240 200 150 120

Pressure

∆BarCont. 175 175 175 155 125 125 100

Int. 200 200 200 190 150 150 120

∆PSICont. 2538 2538 2538 2248 1813 1813 1450

Int. 2901 2901 2901 2756 2176 2176 1740

Torque

NMCont. 500 614 777 866 877 1128 1146

Int. 573 700 888 1061 1053 1350 1375

LBF-INCont. 4425 5434 6877 7665 7762 9984 10143

Int. 5071 6196 7859 9391 9320 11949 12170



Genuine Metaris Orbital Motor MMW

Model Code

Series


Flange & PilotA = 4-Bolt Wheel Flange, pilot Ø82.5 (3.25”)

PaintA = No PaintB = BlackC = Blue (Standard)Options A & B (or any other color needed) will only be considered for Large Quantity Orders

Rotation0 = Standard (Clock-wise)1 = Opposite (Counter Clock-wise)

Drain PortA = 7/16”-20UNF, O-ringB = G 1/4 BSPAll motors come with a Steel Hex Socket Plugged Drain Port

PortsA = 7/8”-14UNF, O-ringB = G 1/2, BSP

MMW - 01 - A - 01 - A - A - C - 0

Shafts01 = 31.75mm (1.25”) Tapered, Flat key 7.96 x 7.96 x 2202 = 31.75mm (1.25”) Straight, Flat key 7.96 x 7.96 x 3503 = 32mm (1.26”) Straight, Flat key 9.98 x 7.99 x 4504 = 31.75mm (1.25”) 14t Splined



MMW SeriesMMWSpecifications


Side Load

Shaft Seal



Performance DataMMWSpecifications



Performance DataMMWSpecifications



MMWDimensions

Dimensions - Aligned PortsDispl. cm³/r. 200 245 310 390 490 630 800

XInches (.88) (1.08) (1.36) (1.71) (2.15) (2.73) (3.51)

Millimeters 22.4 27.4 34.6 43.4 54.5 69.2 89.1

YInches (5.92) (6.12) (6.41) (6.75) (7.19) (7.77) (8.55)

Millimeters 150.4 155.5 162.7 171.5 182.6 197.3 217.2

For complete shaft dimensions, see page ??



MMWFlanges Mounting Flanges

(A) = 4-Bolt Wheel Flange, Pilot 82.6 (3.25”)



MMWShafts

Shafts



MMWShafts

Shafts



Spool Valve Motors - NotesGeneral



MMS SeriesGeneral

MMS series motors are disc valve motors, with the characteristic features of: • Compact and light weight design • Advanced Roller-Star technology, requiring lower pressure at start-up and providing smooth reliable operation at all speeds • Disc valve technology, providing greater speed and efficiency for medium duty applications • Dual high efficiency tapered roller bearings, providing excellent low speed and high speed operation with high side load capabilities • High pressure shaft seal, which allows for higher back pressures and an increased ability to handle high pressure spike conditions (no shaft seal on bearingless motors) • Internal integrated check valve, which limits case pressure by blocking the high pressure port side and allowing the motor housing to drain into the outlet (low pressure) port. Motors connected in series will utilize the case drainThese motors can be used in parallel or series. A diverse offering of mounting flanges, shafts, ports, and displacements along with wheel and bearingless motors allow for easy installation, product replacement, orOEM application.


Description

Specifications Model Code 01 02 03 04 05 06 07 08 09

Displ.cm³/r 80 100 130 160 195 245 305 395 490

in³/r 4.9 6.1 7.9 9.8 11.9 15 18.6 24.1 29.9

Flow

LPMCont. 75 75 75 75 75 75 75 75 75

Int. 75 95 95 115 115 115 115 130 130

GPMCont. 19.8 19.8 19.8 19.8 19.8 19.8 19.8 19.8 19.8

Int. 19.8 25.1 25.1 30.4 30.4 30.4 30.4 34.3 34.3

Max Speed RPM

Cont. 799 742 576 477 385 308 246 191 153

Int. 908 924 720 713 577 462 365 335 230

Pressure

∆BarCont. 170 170 170 170 170 170 140 140 120

Int. 275 275 275 240 240 240 205 170 140

∆PSICont. 2466 2466 2466 2466 2466 2466 2031 2031 1740

Int. 3989 3989 3989 3481 3481 3481 2973 2466 2031

Torque

NMCont. 195 245 315 380 455 555 560 700 845

Int. 305 395 505 530 625 765 805 890 930

LBF-INCont. 1726 2168 2788 3363 4027 4912 4956 6196 7479

Int. 2700 3496 4470 4691 5532 6771 7125 7877 8231



Genuine Metaris Orbital Motor MMS

Series

Displacement cm³/r (in³/r) 01 = 80 (4.9)02 = 100 (6.1)03 = 130 (7.9)04 = 160 (9.8)05 = 195 (11.9)06 = 245 (15.0)07 = 305 (18.6)08 = 395 (24.1)09 = 490 (29.9)

Flange & PilotA = 4-Bolt SAE “B” Flange, pilot Ø100 (3.94”)B = 2-Bolt SAE “A” Flange, pilot Ø82.5 (3.25”)(Can be replaced by E)C = 4-Bolt SAE “A” Flange, pilot Ø82.5 (3.25”)D = 4-Bolt Wheel Flange, pilot Ø107.9 (4.25”)E = 6-Bolt Magneto Flange, pilot Ø82.5 (3.25”)(Can be replacement for B or G)F = 2-Bolt Rhomb Flange, pilot Ø80 (3.15”)G = 4-Bolt Magneto Flange, pilot Ø82.5 (3.25”)(Can be replaced by E)H = 2-Bolt SAE “B” Flange, pilot Ø101.5 (4”)I = 4-Bolt Square Bearingless Flange

Model Code



Ports & Drain PortA = 7/8”-14UNF, O-ring & 7/16”-20UNF B = G 1/2, BSP & G 1/4 BSPC = M22 x 1.5 & M14 x 1.5(Manifold Mount 3-M10)D = G 1/2 & M14 x 1.5, O-ringE = G 1/2 & G 1/4(Manifold Mount 3-M10)F = M14 x 1.5 & M14 x 1.5G = M22 x 1.5 & M10 x 1H = Not AvailableI = M20 x 1.5 & M14 x 1.5J = 1/2”-14NPTF & 7/16”-20UNFK = 1-1/16”-12 O-ring (Positioned 180° apart) & 7/16”-20UNFL = End Port, 7/8”-14UNF, O-ring& 7/16”-20UNFM = End Port, G 1/2, BSP & G 1/4 BSPN = 12.70mm (.50”) & 15.88mm (.625”) & 7/16”-20UNF (Manifold Mount 3-3/8”)O = 12.70mm (.50”) & 15.88mm (.625”) & G 1/4 BSP (Manifold Mount 3-M10)P = 4-5/16”-18UNC (Manifold)Q = 4-M8x1.5 (Manifold)All motors come with a Steel Hex Socket Plugged Drain Port

MMS - 01 - A - 01 - D - B - A

Shafts01 = 25.6mm (1”) Square Spline, 6D - 30 x 26 x 802 = 25mm (.98”) Straight, Flat key 8mm03 = 26mm (1.02”) Square Spline, 6D - 30 x 26 x 604 = 25.4mm (1”) Straight, Woodruff key 6.35mm05 = 31.75mm (1.25”) Straight, Flat key 7.96mm06 = 31.75mm (1.25”) Tapered, Flat key 7.96mm07 = 31.75mm (1.25”) 14t, Splined08 = 25.4mm (1”) Square Spline, 6D - 25.4 x 21.5 x 6.2509 = 25.4mm (1”) Straight, Flat key 6.35mm10 = 30mm (1.18”) Straight, Flat key 10mm11 = 22mm (.87”) Straight, Flat key 6mm12 = 32mm (1.26”) Straight, Flat key 10mm13 = 25mm (.98”) Straight, Flat key 8mm14 = 25.4mm (1”) SAE 6B Splined15 = 22.2mm (.875”) SAE “B” 13t, Splined16 = Bearingless



MMS SeriesMMSSpecifications


Side Load

Shaft Seal



Performance DataMMSSpecifications















MMSDimensions

MMSDimensions

Dimensions - Staggered Ports

Dimensions - Wheel Mount (Flange Code: D)

Displ. cm³/r. 80 100 130 160 195 245 305 395 490

XInches (.57) (.70) (.89) (1.14) (1.40) (1.76) (2.20) (2.83) (3.52)

Millimeters 14.4 17.8 22.5 28.9 35.6 44.7 56.0 72.0 89.3

YInches (7.24) (7.44) (7.68) (7.68) (7.95) (8.31) (8.78) (9.41) (10.08)

Millimeters 184 189 195 195 202 211 223 239 256

Displ. cm³/r. 80 100 130 160 195 245 305 395 490

XInches (.57) (.70) (.89) (1.14) (1.40) (1.76) (2.20) (2.83) (3.52)

Millimeters 14.4 17.8 22.5 28.9 35.6 44.7 56.0 72.0 89.3

YInches (5.67) (5.83) (6.10) (6.10) (6.38) (6.73) (7.17) (7.80) (8.50)

Millimeters 144 148 155 155 162 171 182 198 216



MMSDimensions

Dimensions - Bearingless (Flange Code: I, Shaft Code: 16)

Dimensions - Shaft Code: 16

Displ. cm³/r. 80 100 130 160 195 245 305 395 490

XInches (.57) (.70) (.89) (1.14) (1.40) (1.76) (2.20) (2.83) (3.52)

Millimeters 14.4 17.8 22.5 28.9 35.6 44.7 56.0 72.0 89.3

YInches (5.00) (5.16) (5.43) (5.43) (5.71) (6.06) (6.50) (7.13) (7.80)

Millimeters 127 131 138 138 145 154 165 181 198



MMSFlanges Mounting Flanges

(A) = 4-Bolt SAE “B” Flange, Pilot 100 (3.94”)

(C) = 4-Bolt SAE “A” Flange, Pilot 82.5 (3.25”)

(E) = 6-Bolt Magneto Flange, Pilot 82.5 (3.25”)

(B) = 2-Bolt SAE “A” Flange, Pilot 82.5 (3.25”)

(D) = 4-Bolt Wheel Flange, Pilot 107.9 (4.25”)

[For Dimensions - see page 50 ]

(F) = 2-Bolt Rhomb Flange, Pilot 80 (3.15”)



MMSFlanges Mounting Flanges

(G) = 4-Bolt Magneto Flange, Pilot 82.5 (3.25”)

(I) = 4-Bolt Square Flange, Pilot 101.5 (4”)

[Bearingless - see page 51]

(H) = 2-Bolt SAE “B” Flange, Pilot 101.5 (4”)



MMSShafts

Shafts



MMSShafts

Shafts



MMSDimensions

Port Dimensions



MMS Series - NotesGeneral



General


Specifications Model Code 01 02 03 04 05 06 07 08 09

Displ.cm³/r 110 130 160 205 245 310 395 495 625

in³/r 6.7 7.9 9.8 12.5 15.0 18.9 24.1 30.2 38.1

Flow

LPMCont. 75 95 95 95 95 95 95 95 95

Int. 95 115 115 115 130 130 150 150 150

GPMCont. 19.8 25.1 25.1 25.1 25.1 25.1 25.1 25.1 25.1

Int. 25.1 30.4 30.4 30.4 34.4 34.4 39.6 39.6 39.6

Max Speed RPM

Cont. 697 722 582 459 383 303 239 191 151

Int. 868 862 693 546 532 422 376 305 241

Pressure

∆BarCont. 205 205 205 205 205 205 190 140 115

Int. 310 310 310 310 260 260 240 170 140

∆PSICont. 2973 2973 2973 2973 2973 2973 2756 2031 1668

Int. 4496 4496 4496 4496 3771 3771 3481 2466 2031

Torque

NMCont. 320 375 485 600 705 850 930 945 970

Int. 470 560 705 800 845 1065 1185 1170 1180

LBF-INCont. 2832 3319 4293 5310 6240 7523 8231 8364 8585

Int. 4160 4956 6240 7081 7479 9426 10488 10355 10444

MMK series motors are disc valve motors, with the characteristic features of: • Compact and light weight design • Advanced Roller-Star technology, requiring lower pressure at start-up and providing smooth reliable operation at all speeds • Disc valve technology, providing greater speed and efficiency for medium duty applications • Dual high efficiency tapered roller bearings, providing excellent low speed and high speed operation with high side load capabilities • High pressure shaft seal, which allows for higher back pressures and an increased ability to handle high pressure spike conditions (no shaft seal on bearingless motors) • Internal integrated check valve, which limits case pressure by blocking the high pressure port side and allowing the motor housing to drain into the outlet (low pressure) port. Motors connected in series will utilize the case drainThese motors can be used in parallel or series. A diverse offering of mounting flanges, shafts, ports, and displacements along with wheel and bearingless motors allow for easy installation, product replacement, orOEM application.

Description

MMK Series



Genuine Metaris Orbital Motor MMK

Model Code

Series

Displacement cm³/r (in³/r) 01 = 110 (6.7)02 = 130 (7.9)03 = 160 (9.8)04 = 205 (12.5)05 = 245 (15.0)06 = 310 (18.9)07 = 395 (24.1)08 = 495 (30.2)09= 625 (38.1)

Flange & PilotA = 4-Bolt SAE “B”, pilot Ø101.6 (4.00”)B = 4-Bolt SAE “C”, pilot Ø127 (5.00”)C = 4-Bolt Wheel Flange, pilot Ø139.7 (5.50”)D = 4-Bolt Bearingless, pilot Ø127 (5.00”)E = 4-Bolt Flange, pilot Ø125 (4.92”)F = 4-Bolt Bearingless, pilot Ø125 (4.92”)

Seals0 = Buna (Standard)1 = Viton Shaft Seal & Buna Seals2 = Buna Shaft Seal & Viton Seals3 = Viton Shaft Seal & Viton Seals


Ports & Drain PortA = 1-1/16”-12UNF, O-ring & 7/16”-20UNF, O-ringB = G 3/4, BSP & G 1/4, BSPC = 4-Bolt Split Flange (to fit SAEJ518C2) & 7/16”-20UNF, O-ringD = 7/8”-14UNF, O-ring & 9/16”-18UNF, O-ringE = M22 x 1.5-6H & M12 x 1.5-6HAll motors come with a Steel Hex Socket PluggedDrain Port

MMK - 01 - A - 01 - A - 1 - 0 - A

Shafts01 = 31.75mm (1.25”) Straight, Flat key 7.96mm(Available with Code A, B & C Flange Only)02 = 31.75mm (1.25”) 14t, Splined(Available with Code A, B & C Flange Only)03 = 40mm (1.57”) Straight, Flat key 11.96mm(Available with Code A, B & C Flange Only)04 = 38.1mm (1.50”) 17t, Splined(Available with Code B Flange Only)05 = 41.275mm (1.625”) Tapered(Available with Code A & C Flanges Only)06 = Bearingless(Available with Code D Flange Only)

Paint0 = No Paint1 = Blue (Standard)2 = BlackOptions 0 & 2 (or any other color needed) will only be considered for Large Quantity Orders



MMK SeriesMMKSpecifications


Side Load

Shaft Seal



Performance DataMMKSpecifications












MMKDimensions

MMKDimensions

Dimensions - Configuration Flange A

Dimensions - Configuration Flange B

Displ. cm³/r. 110 130 160 205 245 310 395 495 625

XInches (.57) (.67) (.83) (1.06) (1.26) (1.60) (2.03) (2.54) (3.20)

Millimeters 14.4 17.1 21.1 26.8 32.1 40.6 51.5 64.5 81.4

Y1Inches (6.02) (6.14) (6.30) (6.54) (6.73) (7.09) (7.48) (7.99) (8.66)

Millimeters 153 156 160 166 171 180 190 203 220

Y2Inches (8.23) (8.35) (8.50) (8.74) (8.94) (9.29) (9.69) (10.20) (10.86)

Millimeters 209 212 216 222 227 236 246 259 276

Displ. cm³/r. 110 130 160 205 245 310 395 495 625

XInches (.57) (.67) (.83) (1.06) (1.26) (1.60) (2.03) (2.54) (3.20)

Millimeters 14.4 17.1 21.1 26.8 32.1 40.6 51.5 64.5 81.4

Y1Inches (6.22) (6.30) (6.46) (6.69) (6.89) (7.24) (7.64) (8.15) (9.21)

Millimeters 158 160 164 170 175 184 194 207 224

Y2Inches (8.43) (8.50) (8.66) (8.90) (9.09) (9.45) (9.84) (10.35) (11.02)

Millimeters 214 216 220 226 231 240 250 263 280



MMKDimensions

MMKDimensions

Dimensions - Configuration Wheel Mount Flange C

Dimensions - Configuration Bearingless Flange D

Displ. cm³/r. 110 130 160 205 245 310 395 495 625

XInches (.57) (.67) (.83) (1.06) (1.26) (1.60) (2.03) (2.54) (3.20)

Millimeters 14.4 17.1 21.1 26.8 32.1 40.6 51.5 64.5 81.4

Y1Inches (3.12) (3.23) (3.39) (3.61) (3.81) (4.15) (4.58) (5.09) (5.76)

Millimeters 79 82 86 92 97 106 116 129 146

Y2Inches (5.33) (5.43) (5.59) (5.81) (6.02) (6.36) (6.79) (7.30) (7.96)

Millimeters 135 138 142 148 153 162 172 185 202

Displ. cm³/r. 110 130 160 205 245 310 395 495 625

XInches (.57) (.67) (.83) (1.06) (1.26) (1.60) (2.03) (2.54) (3.20)

Millimeters 14.4 17.1 21.1 26.8 32.1 40.6 51.5 64.5 81.4

Y1Inches (3.32) (3.43) (3.58) (3.81) (4.02) (4.35) (4.78) (5.29) (5.96)

Millimeters 84 87 91 97 102 111 121 134 151

Y2Inches (5.52) (5.63) (5.79) (6.01) (6.22) (6.56) (6.98) (7.50) (8.16)

Millimeters 140 143 147 153 158 167 177 190 207



MMKFlanges Mounting Flanges

(A) = 4-Bolt SAE “B”, Pilot 101.6 (4.00”)

(B) = 4-Bolt SAE “C”, Pilot 127 (5.00”)



MMKFlanges Mounting Flanges

(C) = 4-Bolt Wheel Flange, Pilot 139.7 (5.50”)

(D) = 4-Bolt Bearingless, Pilot 127 (5.00”)



MMKShafts

Shafts



MMT SeriesGeneral


Specifications Model Code 01 02 03 04 05 06 07 08

Displ.cm³/r 195 245 310 390 490 625 800 985

in³/r 11.9 15.0 18.9 23.8 29.9 38.1 48.8 60.1

Flow

LPMCont. 150 150 150 150 150 150 150 150

Int. 170 210 225 225 225 225 225 225

GPMCont. 39.6 39.6 39.6 39.6 39.6 39.6 39.6 39.6

Int. 44.9 55.5 59.4 59.4 59.4 59.4 59.4 59.4

Max Speed RPM

Cont. 775 615 698 387 306 240 184 153

Int. 866 834 485 570 454 355 278 230

Pressure

∆BarCont. 170 170 170 170 170 120 120 120

Int. 275 275 275 275 240 140 140 140

∆PSICont. 2466 2466 2466 2466 2466 1740 1740 1740

Int. 3989 3989 3989 3989 3481 2031 2031 2031

Torque

NMCont. 475 615 775 965 1215 1125 1308 1570

Int. 770 980 1225 1455 1685 1330 1650 1875

LBF-INCont. 4204 5443 6859 8541 10754 9957 11577 13896

Int. 6815 8674 10842 12878 14914 11772 14604 16595

MMT series motors are disc valve motors, with the characteristic features of: • Compact and light weight design • Advanced Roller-Star technology, requiring lower pressure at start-up and providing smooth reliable operation at all speeds • Disc valve technology, providing greater speed and efficiency for medium duty applications • Dual high efficiency tapered roller bearings, providing excellent low speed and high speed operation with high side load capabilities • High pressure shaft seal, which allows for higher back pressures and an increased ability to handle high pressure spike conditions (no shaft seal on bearingless motors) • Internal integrated check valve, which limits case pressure by blocking the high pressure port side and allowing the motor housing to drain into the outlet (low pressure) port. Motors connected in series will utilize the case drainThese motors can be used in parallel or series. A diverse offering of mounting flanges, shafts, ports, and displacements along with wheel and bearingless motors allow for easy installation, product replacement, orOEM application.

Description



Genuine Metaris Orbital Motor MMT

Model Code

Series

Displacement cm³/r (in³/r) 01 = 195 (11.9)02 = 245 (15.0)03 = 310 (18.9)04 = 390 (23.8)05 = 490 (29.9)06 = 625 (38.1)07 = 800 (48.8)08 = 985 (60.1)

Flange & PilotA = 4-Bolt SAE Cc Flange, pilot Ø127 (5.00”)B = 4-Bolt Flange, pilot Ø125 (4.92”)C = 4-Bolt Wheel Flange, pilot Ø139.7 (5.50”)D = 4-Bolt Square Mount, pilot Ø160 (6.30”)E = 4-Bolt Global Mount, pilot Ø160 (6.30”)Similar to ISO3019/2F = 4-Bolt Square, Bearingless, pilot Ø127 (5.00”)


Ports & Drain PortA = G 1, BSP & G 1/4, BSP B = 1-5/16”-12 O-ring & 7/16”-20UNFC = M33 x 2 & M14 x 1.5D = M33 x 2 & G 1/4 O-ringE = Standard Manifold Port FaceF = Not AvailableG = G 3/4 & G 1/4, O-ringH = M22 x 1.5 & M14 x 1.5I = M24 x 1.5 & M14 x 1.5J = Not AvailableK = 4-Bolt 3/4” Split Flange (to fit SAEJ518C2) & 7/16”-20UNF, O-ringAll motors come with a Steel Hex Socket PluggedDrain Port

All motors for this Series come with Standard (Clockwise) Rotation. For Counter Clockwise Rotation pressurize Port B.

MMT - 01 - A - 01 - D - 1 - A

Shafts01 = 38.1mm (1.50”) Straight, Flat key 9.56mm02 = 40mm (1.57”) Straight, Flat key 12mm (L=84-86mm)03 = 40mm (1.57”) Straight, Flat key 12mm (L=77.7-80.1mm)04 = 36mm (1.42”) Square Spline 8D-42 x 36 x 7 (L=69mm)05 = 36mm (1.42”) Square Spline 8D-42 x 36 x 7 (L=72-74mm)06 = 36mm (1.42”) Square Spline 6D-40 x 35 x 10 (L=66.5-68.5mm)07 = 50mm (1.97”) Straight, Flat key 14mm08 = Non-Standard09 = 40mm (1.57”) Straight, Flat key 12mm (L=58mm)10 = Non-Standard11 = 44.42mm (1.75”) Tapered12 = 35mm (1.38”) Straight, Flat key 12mm (L=84-86mm)13 = 36mm (1.42”) Square Spline 6D-40 x 35 x 10 (L=84-86mm)14 = Non-Standard15 = Non-Standard16 = Non-Standard17 = Non-Standard18 = 38.1mm (1.5”) 17t Splined19 = 40mm (1.57”) Straight, Flat key 12mm “US Standard”20 = Bearingless

StyleA = StandardB = Large BoltC - Wheel



MMT SeriesMMTSpecifications


Side Load

Shaft Seal



Performance DataMMTSpecifications












MMTDimensions

MMTDimensions

Dimensions - Configuration Flanges A & B

Dimensions - Configuration Flanges D & E

Displ. cm³/r. 195 245 310 390 490 625 800 985

XInches (.86) (1.08) (1.36) (1.71) (2.14) (2.72) (3.50) (4.29)

Millimeters 22 27 35 44 54 69 89 109

Y1Inches (10.63) (10.87) (11.14) (11.50) (11.93) (12.52) (13.11) (14.09)

Millimeters 270 276 283 292 303 318 333 358

Y2Inches (5.91) (6.14) (6.42) (6.77) (7.20) (7.80) (8.43) (9.33)

Millimeters 150 156 163 172 183 198 214 237

Displ. cm³/r. 195 245 310 390 490 625 800 985

XInches (.86) (1.08) (1.36) (1.71) (2.14) (2.72) (3.50) (4.29)

Millimeters 22 27 35 44 54 69 89 109

Y1Inches (9.06) (9.25) (9.69) (9.88) (10.35) (10.91) (11.54) (12.48)

Millimeters 230 235 246 251 263 277 293 317

Y2Inches (5.31) (5.55) (5.83) (6.18) (6.61) (7.20) (7.83) (8.74)

Millimeters 135 141 148 157 168 183 199 222



MMTDimensions

MMTDimensions

Dimensions - Wheel Mount (Flange Code: C, Shaft Code: 11)

Dimensions - Bearingless (Flange Code: F, Shaft Code: 20)Displ. cm³/r. 195 245 310 390 490 625 800 985

XInches (.86) (1.08) (1.36) (1.71) (2.14) (2.72) (3.50) (4.29)

Millimeters 22 27 35 44 54 69 89 109

YInches (7.01) (7.20) (7.52) (7.87) (8.31) (8.90) (9.88) (10.43)

Millimeters 178 183 191 200 211 226 251 265

Displ. cm³/r. 195 245 310 390 490 625 800 985

XInches (.86) (1.08) (1.36) (1.71) (2.14) (2.72) (3.50) (4.29)

Millimeters 22 27 35 44 54 69 89 109

Y1Inches (7.28) (7.52) (7.80) (8.15) (8.58) (9.17) (9.80) (10.75)

Millimeters 185 191 198 207 218 233 249 273

Y2Inches (4.06) (4.25) (4.57) (4.88) (5.35) (5.91) (7.01) (7.48)

Millimeters 103 108 116 124 136 150 178 190



MMTFlanges Mounting Flanges

(A) = 4-Bolt SAE Cc Flange, Pilot 127 (5”)

(C) = 4-Bolt Wheel Flange, Pilot 139.7 (5.50”)

(E) = 4-Bolt Global Mount, Pilot 160 (6.30”),Similar to ISO3019/2

(B) = 4-Bolt Flange, Pilot 125 (4.92”)

(D) = 4-Bolt Square Mount, Pilot 160 (6.30”)

(F) = 4-Bolt Square Flange, Pilot 127 (5.00”)



MMTShafts

Shafts

08 = Non-Standard Shaft Code



MMTShafts

Shafts

10, 14, 15, 16 & 17 = Non-Standard Shaft Code



MMTDimensions

Port Dimensions



MMT Series - NotesGeneral



MMV SeriesGeneral



Displ.cm³/r 310 400 500 630 800 1000 1250

in³/r 18.9 24.4 30.5 38.4 48.8 61.0 76.3

Flow

LPMCont. 160 200 200 200 200 200 200

Int. 200 240 240 240 240 240 240

GPMCont. 42.3 52.8 52.8 52.8 52.8 52.8 52.8

Int. 52.8 63.4 63.4 63.4 63.4 63.4 63.4

Max Speed RPM

Cont. 510 500 400 315 250 200 160

Int. 630 600 480 380 300 240 190

Pressure

∆BarCont. 200 200 200 180 160 160 150

Int. 240 240 240 210 180 180 170

∆PSICont. 2901 2901 2901 2611 2321 2321 2176

Int. 3481 3481 3481 3046 2611 2611 2466

Torque

NMCont. 920 1180 1460 1660 1880 2340 2740

Int. 1110 1410 1760 1940 2110 2640 3120

LBF-INCont. 8143 10444 12922 14692 16639 20711 24251

Int. 9824 12480 15577 17170 18675 23366 27614

MMV series motors are disc valve motors, with the characteristic features of: • Compact and light weight design • Advanced Roller-Star technology, requiring lower pressure at start-up and providing smooth reliable operation at all speeds • Disc valve technology, providing greater speed and efficiency for heavy duty applications • Dual high efficiency tapered roller bearings, providing excellent low speed and high speed operation with high side load capabilities • High pressure shaft seal, which allows for higher back pressures and an increased ability to handle high pressure spike conditions (no shaft seal on bearingless motors) • Internal integrated check valve, which limits case pressure by blocking the high pressure port side and allowing the motor housing to drain into the outlet (low pressure) port. Motors connected in series will utilize the case drainThese motors can be used in parallel or series. A diverse offering of mounting flanges, shafts, ports, and displacements along with wheel and bearingless motors allow for easy installation, product replacement, orOEM application.

Description



Genuine Metaris Orbital Motor MMV

Model Code

Series


Flange & PilotA = 4-Bolt Square, pilot Ø160 (6.30”)B = 4-Bolt Square, pilot Ø160 (6.30”)C = 4-Bolt SAE “C”, pilot Ø127 (5.00”)D = 4-Bolt Square, pilot Ø127 (5.00”)

Seals0 = Buna (Standard)1 = Viton Shaft Seal & Buna Seals2 = Buna Shaft Seal & Viton Seals3 = Viton Shaft Seal & Viton Seals


Ports & Drain PortA = G 1, BSP & G 1/4, BSPB = 1-5/16”-12UNF, O-ring & 9/16”-18UNF, O-ringC = 16mm (.63”) & G 1/4D = 1-1/4” Split Flange & 9/16”-18UNF, O-ring(Manifold Mount 4-M12)All motors come with a Steel Hex Socket PluggedDrain Port

MMV - 01 - A - 01 - A - 1 - 0 - A

Shafts01 = 50mm (1.97”) Straight, Flat key 13.957mm, M12(Available with Code A & C Flange Only)02 = 57.15mm (2.25”) Straight, Flat key 12.7mm, 3/8-16UNC(Available with Code A Flange Only)03 = 53.95mm (2.125”) 16t, Splined, M12(Available with Code A Flange Only)04 = 53.95mm (2.125”) 16t, Splined, 3/8-16UNC(Available with Code A Flange Only)05 = 45mm (1.77”) 17t, Splined(Available with Code B Flange Only)06 = 57.15mm (2.25”) Straight, Flat key 12.7mm, 1/2-20UNF(Available with Code C Flange Only)07 = 53.95mm (2.125”) 16t, Splined, 1/2-20UNF(Available with Code C Flange Only)08 = 41.95mm (1.65”) Square Splined(Available with Code D Flange Only)09 = 57.15mm (2.25”) Tapered, SAE J501(Available with Code B & C Flange Only)




MMV SeriesMMVSpecifications


Side Load

Shaft Seal



Performance DataMMVSpecifications



Performance DataMMVSpecifications



MMVDimensions

Dimensions - Configuration Flanges A & BDispl. cm³/r. 310 400 500 630 800 1000 1250

XInches (.67) (.93) (1.30) (1.69) (2.24) (2.87) (3.50)

Millimeters 17 24 33 43 57 73 89

Y1Inches (7.95) (8.19) (8.58) (8.98) (9.53) (10.16) (10.79)

Millimeters 202 208 218 228 242 258 274

Y2Inches (5.67) (5.91) (6.30) (6.69) (7.24) (7.87) (8.50)

Millimeters 144 150 160 170 184 200 216



MMVDimensions

Dimensions - Configuration Flange CDispl. cm³/r. 310 400 500 630 800 1000 1250

XInches (.67) (.93) (1.30) (1.69) (2.24) (2.87) (3.50)

Millimeters 17 24 33 43 57 73 89

Y1Inches (8.35) (8.58) (8.98) (9.37) (9.92) (10.55) (11.18)

Millimeters 212 218 228 238 252 268 284

Y2Inches (6.18) (6.42) (6.81) (7.20) (7.76) (8.39) (9.02)

Millimeters 157 163 173 183 197 213 229



MMVDimensions

Dimensions - Configuration Flange DDispl. cm³/r. 310 400 500 630 800 1000 1250

XInches (.67) (.93) (1.30) (1.69) (2.24) (2.87) (3.50)

Millimeters 17 24 33 43 57 73 89

Y1Inches (8.54) (8.78) (9.17) (9.57) (10.12) (10.75) (11.38)

Millimeters 217 223 233 243 257 273 289

Y2Inches (5.79) (6.02) (6.42) (6.81) (7.36) (7.99) (8.62)

Millimeters 147 153 163 173 187 203 219



MMVFlanges Mounting Flanges

(A) = 4-Bolt Square, Pilot 160 (6.30”)

(B) = 4-Bolt Square, Pilot 160 (6.30”)



MMVFlanges Mounting Flanges

(C) = 4-Bolt SAE “C”, Pilot 127 (5.00”)(US Standard)

(D) = 4-Bolt Square, Pilot 127 (5.00”)



MMVShafts

Shafts



MMVShafts

Shafts



MMVShafts

Shafts



Genuine Metaris Orbital Motor Special Options

Model Code

Special Options

Seals A = Buna (Standard)B = Viton Shaft Seal & Buna SealsC = Buna Shaft Seal & Viton SealsD = Viton Shaft Seal & Viton Seals

Setup1 = Standard2 = Free Running3 = Seal Guard4 = Dacromet Screws & Plug5 = Free Running & Dacromet Screws & Plug Shaft Coating

1 = Standard (No Coating)2 = Chrome Plated

W - A - 1 - A - 1 - A

Speed SensorsA = Standard (None)B = Ported & Plugged, No SensorC = Ported with Speed SensorD = Ported with Speed SensorFor speed sensor options contact [email protected] or your local salesman

Motor CoatingA = Standard (No Coating)B = Nickel Plated

Above options are non-stock. Please call or email for availability.

OMLSHT-Rev 07.2014 © 2013 Hydraulex Global. All Rights Reserved.

Hydraulex Global Corporate48175 Gratiot AveChesterfield, MI 48051Toll Free: 800.422.4279Tel: 586.949.4240

www.hydraulex.com

Hydraulex Global - Michigan Tel: 586.949.4240 [email protected] Global - Mississippi Tel: 601.469.1987 [email protected] Global - Ontario Tel: 416.638.6000 [email protected] Global - Washington Tel: 253.604.0400 [email protected] Global - Tennessee Tel: 901.794.2462 [email protected]

Connect with us:

· Inline Piston Pumps· Radial Piston Pumps & Motors· Bent Axis Piston Pumps & Motors· Fixed Volume Vane Pumps· Variable Volume Vane Pumps· Gear Pumps· Vane Motors

· Axial Piston Motors· High Speed Motors· Servo Motors· Orbital Motors· Directional Valves· Flow Control Valves· Pressure Control Valves

· Relief Valves· Check Valves· Stack Valves· Servo Valves· Proportional Valves· PTOs (Power Take-offs)· Cylinders

Products We Offer

Hydraulex Global - A Recognized Global Leading Provider of High Quality Hydraulic Components

All manufacturers names, symbols and descriptions in this document are used for reference purposes only, and it is not implied

that any parts listed is the product of these manufacturers.

Documents

MMPS, MMRSW, MMH, MMW, MMS, MMK, MMT and … MMK, MMT and MMV Series Orbital Motors Technical Information ... Start-up Procedures ... Motor Testing: · Motors tested