7/29/2019 mmb_1215
1/2
8 Parker HannifinCylinder DivisionEurope
Catalogue HY07-1215/UK Roundline Cylinders
MMB SeriesFoot and Trunnion Mountings
Dimensions MS2 and MT4
Style MS2
Foot Mounting
All dimensions are in millimetres unless otherwise stated.
Bore
RodNo.
Rod
BDmax
D&
TEmax
EE(BSPP)
EH KLHh10
SSBH13
TDf8
TLjs15
TMh12
TSjs13
USUVmax
XSXVmin
YMin.
StrokeMT4
+ Stroke
PJ SSXVmax
ZBmax
ZD
401
2
22
2830 78 G1/2 82 13 43 25 11 20 16 90 100 120 78 19.5 130 71 37
97 183 93 198 215
501
2
28
3635 95 G1/2 100 14 52 32 14 25 20 105 120 145 95 22 142 72 40
111 199 102 213 237
631
2
36
4545 116 G3/4 120 16 62 32 18 32 25 120 150 180 116 29 160 82 53
117 211 107 236 256
80
1
2
45
56 50 130 G
3
/4 135 18 70 40 22 40 32 135 170 210 130 34 180 91 53 134 236
122 262 290
1001
2
56
7060 158 G1 161 20 82 50 26 50 40 160 205 250 158 32 210 108 58
162 293 152 314 350
1251
2
70
9075 192 G1 196 23 100 56 33 63 50 195 245 300 195 32 235 121 78
174 321 157 341 381
1601
2
90
11090 232 G11/4 238 25 119 60 33 80 63 240 295 350 240 36 273
143 96 191 364 177 386 430
2001
2
110
140110 285 G11/4 288 30 145 72 39 100 80 295 350 415 390 39 337
190 70 224 447 267 466 522
2501
2
140
180135 365 G11/2 32 125 100 370 480 393 205 95 290 298 570
3201
2
180
220175 450 G11/2 37 160 125 470 600 486 250 116 358 370 684
UV
TD
EE
TM
ZB + stroke
PJ + strokeY
3
2
1
4 D
BD
K
XVTL TL
R3
US
TS
EE
SB
SS + stroke
PJ + strokeY
3
2
1
4
S
EH
S
XS
LH
TE
D
ZD + stroke
Note: XV dimension to be specied by customer. Where the minimum
dimension
is unacceptable, please consult the factory.
Style MT4
Intermediate Fixed Trunnion
See also Rod End Dimensions, page 9 and Trunnion Blocks, page
13
7/29/2019 mmb_1215
2/2
9 Parker HannifinCylinder DivisionEurope
Catalogue HY07-1215/UK Roundline Cylinders
MMB SeriesPiston Rod End Data
Rod End Dimensions
Rod End Codes 4 & 7
Rod End Code 9
Piston Rod End StylesMMB cylinders are supplied with standard
metric male andfemale rod ends to ISO 4395. They can also be
supplied withother rod end threads, eg: ISO metric coarse, Unied,
BritishStandard etc., or to the customer's special
requirements.
Rod End Codes 4 and 9Each cylinder bore size is offered with two
diameters of pistonrod the smaller is designated no. 1 and the
larger, no. 2.The standard male rod end threads, to ISO 6020/1,
aredesignated code 4 and female threads are designated code 9.
Rod End Code 3Non-standard rod ends are designated code 3.
Orders forthese should include dimensioned sketches and
descriptions,showing dimensions KK or KF, A, rod stand out (WF VE)
andthe thread form required.
Rod End Code 7
Where the same pin diameter is required at the head and capends
of a cylinder with mounting styles MP3 or MP5 and a no. 2piston
rod, a code 7 rod end should be specied.
Wrench FlatsPiston rods up to and including 140mm in diameter
aresupplied with the wrench ats D shown in the table below.Rods
above 140mm in diameter feature four drilled holes toaccept a pin
wrench.
All dimensions are in millimetres unless otherwise stated.
Bore
RodNo.
MMRod
Code 4 Code 7 Code 9D NA VE WF
KK A KK A KF A
401 22 M16x1.5 22 M16x1.5 22 18 21
19 322 28 M20x1.5 28 M16x1.5 22 M20x1.5 28 22 26
501 28 M20x1.5 28 M20x1.5 28 22 26
24 382 36 M27x2 36 M20x1.5 28 M27x2 36 30 34
631 36 M27x2 36 M27x2 36 30 34
29 452 45 M33x2 45 M27x2 36 M33x2 45 39 43
801 45 M33x2 45 M33x2 45 39 43
36 542 56 M42x2 56 M33x2 45 M42x2 56 48 54
100 1 56 M42x2 56 M42x2 56 48 54 37 572 70 M48x2 63 M42x2 56
M48x2 63 62 68
1251 70 M48x2 63 M48x2 63 62 68
37 602 90 M64x3 85 M48x2 63 M64x3 85 80 88
1601 90 M64x3 85 M64x3 85 80 88
41 662 110 M80x3 95 M64x3 85 M80x3 95 100 108
2001 110 M80x3 95 M80x3 95 100 108
45 752 140 M100x3 112 M80x3 95 M100x3 112 128 138
2501 140 M100x3 112 M100x3 112 128 138
64 962 180 M125x4 125 M100x3 112 M125x4 125 15 x 4 175
3201 180 M125x4 125 M125x4 125 15 x 4 175
71 1082 220 M160x4 160 M125x4 125 M160x4 160 15 x 4 214
A WF
NA KK
D wrench ats or
pin wrench holes
MM
VE
A
WF
NA KF
D wrench ats or
pin wrench holes
MM
VE
