Owners Copy: Please keep these instructions for future referen ce

This manua l conta ins IMPORTANT SAFETY informa tion.DO NOT PROCEED WITH THE INSTALLATION BEFORE READING THOROUGHLY. N2966N2966N2966N2966

ML700Sect ional & Tilt Garage Door Opener

Installation and Operating Instructions

www.chamberlainanz.com

CONTENTS PAGESAFETY INSTRUCTIONS . . . . . . . . . . . . . . .1DOOR TYPES . . . . . . . . . . . . . . . . . . . . . . . .2TOOLS REQUIRED . . . . . . . . . . . . . . . . . . . .2HARDWARE PROVIDED . . . . . . . . . . . . . . . .2BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . .3COMPLETED INSTALLATION . . . . . . . . . . . .3ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . .3-5INSTALLATION . . . . . . . . . . . . . . . . . . . . . .5-8CONNECT ELECTRIC POWER . . . . . . . . . .8ADJUSTMENT . . . . . . . . . . . . . . . . . . . . .9-10INSTALL PROTECTOR SYSTEM . . . . . . . .10

WIRELESS PROGRAMMING . . . . . . . . .11-12INSTALL DOOR CONTROL . . . . . . . . . . . . .13SPECIAL FEATURES . . . . . . . . . . . . . . . . . .14ACCESSORIES . . . . . . . . . . . . . . . . . . . . . .14REPLACEMENT PARTS . . . . . . . . . . . . .15-16TROUBLE SHOOTING . . . . . . . . . . . . . . . .17CARE OF YOUR OPENER . . . . . . . . . . . . .18MAINTENANCE OF YOUR OPENER . . . . . 18OPERATION OF YOUR OPENER . . . . . . . .18SPECIFICATIONS . . . . . . . . . . . . . . . . . . . .18WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . .19

NOTE: If you r garage has no servic e entran ce door, a 1702AML outside quick release must be installed.This accesso ry allow s manual operation of the garage door from outside in case of power failur e.

1

WARNING• Failur e to comply with the following instr uctio ns may result in serious personal injury or property damage.• Read and fol low all inst ruct ions carefully.• The garage door opene r is designed and tested to offe r safe service provided it is installed andoperated in str ic t accordanc e with the ins tructions in this manual.

These safety alert symbols mean WARNING : A possible risk to pers onal safety orprope rty damage exist s.

START BY READING THESE IMPORTANT SAFETY INSTRUCTIONS

The Protector SystemTMmust be used for allinstall atio ns where the clo sing force asmeasur ed on the bottom of the door is over400N (40kgf). Excessive force will interfere withthe proper operation of the Safety ReverseSystem or damage the garage door.

After installa tion, ensu re that the parts ofthe door do not extend over pub lic footpath sor roads.

Install the wireless wall control (or anyadditional wall control) in a loc ation where thegarage door is vis ible, at a heigh t of at least1.5m and out of the reach of children . Do notallow child ren to operate push button(s) ortransmitter (s). Serious personal injury from aclosing garage door may result from misuse ofthe opener.Permanently faste n the Warning Labels inProminent Places, adjacent to Wall Controlsand manual release mechanisms as a reminderof safe operating procedures.Activate opener only when the door is in fullview, free of obs tructions and the opener isproperly adjuste d. No one shou ld enter orleave the garage while the door is in motio n.

Do not allow children to play near the door,or door con trols.

Disconnec t electric power to the garagedoo r opener before making repairs orremoving cove rs .

KEEP THESE INSTRUCTIONS

Keep garage door balanced. Do not let thegarage door opener compensate for a binding orsticking garage door. Sticking, binding orunbalanced doors must be repaired beforeinstalling this opener.

Do not wear ring s, watc hes or loo se cloth ingwhile installing or servicing a garage door opener.

Frequent ly examin e the door instal lation, inparticular cable, springs and mountings for signs ofwear, damage or imbalance. Do not use if repair oradjustment is needed since springs and hardwareare under extreme tension and a fault can causeserious personal injury.

To avoid serious personal injury fromentanglement, remove all ropes, chains andlocks connected to the garag e door beforeinstalling the door opener.

Insta lla tio n and wir ing must be in compliance withyour local building and electrical codes.

The safety reverse sys tem tes t is veryimportant . Your garage door MUST reverse oncontact with a 40mm obstacle placed on the floor.Failure to properly adjust the opener may result inserious personal injury from a closing garage door.Repeat the test once a month and make anynecessary adju stments .

This opener should not be inst alled in a dampor wet space expose d to weath er.

This appliance is not intended for use by persons(including children) with reduced physical, sensoryor mental capabilities, or lack of experience andknowledge, unless they have been givensupervision or instruction concerning use of theappliance by a person responsible for their safety.

BA C

up to 8.5m2

DOOR TYPES1

21

11mm, 13mm11/13mm

10mm, 8mm,4.5mm, 4mm

2

1019

7

3

45

6

12

13

8

NOTICE

11

15

14

17

18

1

20

16

21

2

(4x)

(2x)(3x)

(4x)(2x)

(2x)

(2x)(4x)

(2x)(1x)(1x)

(1x)

(1x)

(1x)

(1x)

(4x)(7x)

(7x)(3x)

(1x)

9 (1x)

(1) Hex bolt(2) Clevis pin(3) 8mm carriage bolt(4) Wood screws(5) Sheet metal screws(6) Clevis pin(7) Rope(8) Handle(9) Wall mount for 84330AML(10) Anchor(11) Concrete anchor

(12) Lock washer(13) Hex nut(14) Ring fastener(15) Rail grease(16) Lock nut(17) Metric tapping screw(18) Hex screw(19) Chain tensioner(20) Flat washer(21) Stop bolt

HARDWARE PROVIDED3

2

TOOLS REQUIRED

A. Sectional Door with curved trackB. One-Piece Door with Horizontal Track

OnlyC. One-Piece Door without track

To suit spring balance d sectionaldoors and spring balanc ed tracked

tilt doors up to 12.5m2, or spr ingbalanced til t doors without track up

to 8.5m2.

ASSEMBLY SECTION

As you proceed with the assembly, installation and adjustment procedures in this manual, you may find it helpfulto refer back to this illustration of a completed installation for tilt doors (for sectional doors refer section 20).

1 2 3

12

4 5

9

7

11

13

14

6

815

10

(1) Header sleeve(2) Idler pulley bracket(3) Trolley(4) Rail(5) Chain(6) Hanging bracket(7) Power cord(8) Opener(9) Light lens(10) Manual release

rope & handle(11) Curved door arm(12) Straight door arm(13) Door bracket

and plate(14) Header bracket(15) Trolley release arm(16) Manual (this document)

Grease inside edges of rail sections using grease (1).Place rail pieces (2) on flat surface for assembly. All fourrail sections are interchangeable. Slide rail brace (3) ontorail section. Connect rail by sliding rail brace onto next railsection. Tap rail assembly (4) on piece of wood (5) until railsections are flush. Repeat with remaining rail sections.

4

5

2

3

2

1

4

Manual

BEFORE YOU BEGIN:1. Look at the wall or ceiling above the garage door. The header bracket must be securely fastened to structural

supports.2. Do you have a finished ceiling in your garage? If so, a support bracket and additional fastening hardware (not

supplied) may be required.3. Do you have an access door in addition to the garage door? If not, Model 1702AML outside quick release

accessory is required. This accessory allows manual operation of the garage door from outside in case ofpower failure.

4. Complete the following test to make sure your garage door is balanced and is not sticking or binding:• Lift the door about halfway. Release the door. If balanced, it should stay in place, supported

entirely by its springs.• Raise and lower the door to see if there is any binding or sticking. If your door binds, sticks, or is out of

balance, call a trained door systems technician before proceeding with installation.

16

3

COMPLETED INSTALLATION - ALL PARTS LISTED ARE SUPPLIED IN THE CARTON

ASSEMBLE THE RAIL (SECTIONAL RAIL)5

Remove chain from the carton and lay it out on the floor(be careful not to allow the chain to twist).

Push the pins of the master link bar (3) through chain link(4) and hole in trolley (5). Push cap (2) over the pins andslide clip-on spring (1) over cap and onto pin notches untilboth pins are securely locked into place.

5

4

3

1

2

INSTALL THE CHAIN6

4

1

6

2

3

4

5

3

5

Remove the four washered bolts (1) from top of theopener. Place rail (2) on opener, flush with stop (3)on top of opener. Wrap chain (4) over sprocket (5).Push idler pulley bracket assembly toward front ofthe rail to eliminate excess slack in chain. Align boltholes on brackets (6) with bolt holes on opener.Secure brackets to opener with previously removedbolts. Tighten bolts securely.

The opener sprocket teeth must engage thechain.

4

7

63

Place sprocket cover (1) on top of the opener (2), securewith screws (3). Insert bolt (4) into trolley stop hole (5),secure with washer (6) and nut (7).

1

3

2

Slide outer trolley (1) into the backend of the rail assembly (2), be sureend with trolley release arm (3) ispointing in direction of the openerend. Slide outer trolley down railuntil it engages with inner trolley.

Turn rail assembly over ready fornext operation.

3

1

67

2

5

4

Opener end

ATTACH TROLLEY TO RAIL

FASTEN RAIL TO OPENER AND INSTALL CHAIN

CAUTION: Use only thos e bolt s moun ted in thetop of opene r. Use of any other bol ts will causeserious damage to opener.

ATTACH SPROCKET COVER

12

3

4

5

7Slide idler pulley bracket (1) and inner trolley (2)into the end of rail assembly (3), be sure to insertidler pulley bracket as shown. Arrow on trolley (7)must face toward front (header) end of rail (4).Push idler pulley bracket toward front (header)end of rail (4). Insert carriage bolt (5) into bolt cut-out in the idler pulley bracket (6).

INSERT TROLLEY & IDLER PULLEY BRACKET INTO RAIL7

8

9

5

46

10

Wear prote cti ve goggles when work ing overhe ad to protec t your eyes from injury.Disengage all exis ting garage door loc ks to avoid damage to the garage door.To avoid serious personal injur y from entanglement, remove all ropes conne cted to the garage doorbefore ins tall ing the opener .

NOTE: Where possib le it is recommended that the opener be install ed 2.1m (7 feet) or more above the floor.

The header bracket must be securely fastened to astructural support of the garage. Reinforce the wall orceiling with a 40mm (1-1/2" ) board if neces sary . Failureto comply may result in impr oper opera tion of safetyreverse sys tem.You can attach the header bracket either to the header wall(1) or to the ceiling (3). Follow the instructions that best suityour particular requirements. With the door closed, markthe vertical centreline (2) of the garage door. Extend lineonto header wall above the door.Open door to highest point of travel. Draw an intersectinghorizontal line (4) on header wall 50mm or 200mm abovehigh point to provide travel clearance for top edge of thedoor. Height depends on door type (refer section 15).

3

1

2

4

12

NOTE: Refer to vertical centre and horizontal line screated in secti on 12 for proper placement ofheader brack et.

A. Wall mount: Centre the header bracket (1) on thevertical centre line (2) with the bottom edge of theheader bracket on the horizontal line (4) (with thearrow pointing toward the ceiling). Mark all of theheader bracket holes (5). Then drill 4.5mm (3/16")pilot holes and fasten the header bracket with woodscrews (3).

B. Ceiling mount: Extend vertical centre line (2) ontothe ceiling. Centre the header bracket (1) on thevertical mark no more than 150mm (6") from the wall.Make sure the arrow is pointing towards the opener.Mark all of the header bracket holes (5). Then drill4.5mm (3/16") pilot holes and fasten the headerbracket with wood screws (3). For concrete ceilingmount, use concrete anchors provided.

13

INSTALLATION SECTION

5

2

50mm

31

4

B

A

150mm(6")

1 2

3

5

5

2

31

4

200mm(50 to 200mm depending on door type)

POSITION THE HEADER BRACKET

INSTALL THE HEADER BRACKET

Thread spring nut on carriage bolt until finger tight.Insert a screwdriver tip (1) into one of the slots ofthe nut ring (2) and brace it firmly against theheader sleeve. Place an open end wrench (3) onthe square end of the spring nut (4), slightly rotatenut about 1/4 turn clockwise until nut ring (2) isreleased against header sleeve (5). This setsspring to optimum chain tension. Chain may slipoff sprocket if chain is too loose. If chain does slipre-tighten spring nut by turning nut clockwise a halfturn. Do NOT over-tighten chain.

123

45

ASSEMBLE HEADER SLEEVE & CHAIN TENSIONER11

POSITION THE OPENER

SECTIONAL DOOR OR TRACKED TILTDOOR

You will need a 50mm piece of timber or similarspacer to gauge the distance between door and rail.

1. Raise the opener up onto support.2. Open the door completely, place a 50mm spacer

between the door and the rail (as shown).3. If the top section or panel hits the trolley when you

raise the door, pull down on the trolley arm todisengage the motor. Leave the trolley in thisposition until motor is fastened in place.

ONE PIECE TILT DOOR (NON TRACKED)

You will need a 100mm (4”) piece of timber or similarspacer to gauge the distance between door and rail.

1. Raise the opener onto support.2. Open the door completely, place a 100mm

spacer between the door and the rail (as shown).3. The top of the door should be level with the top

of the motor. Do not position the opener morethan 50mm (2”) above this point.

15 Rail

Door50mm spacer shouldbe used to determinethe correct mountingposition

HeaderBracket

50mm (2”)above the highestpoint of travel

HeaderBracket

50mm spacer shouldbe used to determinethe correct mountingposition

50mm (2”)above the highestpoint of travel

Door

Rail

100mm spacer shouldbe used to determinethe correct mountingposition

Door

Header200mm (8”)above the highestpoint of travel

Bracket

Rail

Position the opener on the garage floor below the headerbracket. Place packing material under the opener to protectthe cover. Raise rail until holes in the header sleeve andholes in the header bracket align. Join with clevis pin (1).Insert ring fasteners (2) to secure.

NOTE: To enable the rail to clear the sectional doorsprings , it may be necessar y to lift opene r onto atemporary support. The opener must either be secur edto a support or held firm ly in plac e by another person.

2 2

1 1

1

2

14

6

DoorA

DoorB

DoorC

ATTACH RAIL TO HEADER BRACKET

Thread one end of rope (1) through hole in top of red handle so"NOTICE" reads right side up as shown (3). Secure with anoverhand knot (2). Knot should be at least 25mm (1") from endof the rope to prevent slipping.

Thread other end of rope through hole in release arm of theouter trolley (4). Adjust rope length so that handle is less than1.8m (6 feet) above the floor. Secure with an overhand knot.

NOTE: If it is necessary to cut rope, heat seal cut end topreve nt fray ing .

Door should be released in the closed position if poss ible.

To release the trolley PULL down on the red handle.

To re-engage PULL the red handle back towards the opener(trolley will re-engage automatically when operated).

DO NOT USE THE HANDLE TO OPEN OR CLOSE THE DOOR.

17

The opene r mus t be secure ly fastened to astructural support of the garage.Three representative installations are shown.Yours may be different. Hanging brackets (1)should be angled (Figure A) to provide rigidsupport. On finished ceilings, (Figure B) attach asturdy metal bracket (not supplied) (4) to astructural support before installing the opener. Forconcrete ceiling mount, (Figure C), use concreteanchors (5) provided.

On each side of opener measure the distancefrom the opener to the structural support (orceiling).

Cut both pieces of the hanging bracket to requiredlengths. Flatten one end of each bracket and bendor twist to fit the fastening angles. Do not bend atthe bracket hole s. Drill 4.5mm (3/16") pilot holesin the structural supports (or ceiling).

Attach brackets to supports with wood screws (2).

Lift opener and fasten to hanging brackets withscrew, lock washer and nut (3). Check to makesure rail is centred over the door. REMOVE 50mmor 100mm board. Operate door manually. If doorhits the rail, raise header bracket. Use rail greaseand lubricate bottom inside surface of rail (6).

A

C

3

12 2

5

1

2

31

B2

4

1 3

3

2

5

2

3

6

6

6

16

DO NOT DISENGAGE THE OPENER IF ANY PERSONS OR OTHER OBJECTS INCLUDING MOTOR VEHICLESARE WITHIN THE DOORWAY: (The door is under signific ant tens ion and if the door has developed a fault orinco rrect tensio n, it may be uns afe and may fall rapidly ).

7

ATTACH EMERGENCY RELEASE ROPE & HANDLE

HANG THE OPENER

A. ONE-PIECE DOOR INSTALLATION:

Fasten the straight (1) and curved (2) door arm sectionstogether to the longest possible length (with a 2 or 3 holeoverlap) using carriage bolts (3), lock washers (4) and hexnuts (5). With the door closed connect the straight door armsection (1) to the door bracket with clevis pin (6). Secure withring fastener (7). Disconnect the inner and outer trolley. Slidethe outer trolley back toward the opener and join the curvedarm (2) to the connector hole in the trolley (8) with clevis pin(6). It may be necessary to lift the door slightly to make theconnection. Secure with ring fastener (7).

NOTE: When setting the up lim it, the door should nothave a “ba ckward” slant in fully open position. A slightbackward slant (9) will cause unne cessary buckingand/or jerki ng whilst operat ing the door.

B. SECTIONAL DOOR INSTALLATION:

Connect according to Figure B, then proceed toSection 21.

7

6

2

9

1

8

4 5

3

A

4

3

5

B

76

6

1

2

20

Sectional and one-piece door insta llation procedur e:

Door bracket (1) has left and right side fastening holes. Ifyour installation requires top and bottom fastening holesuse both the door bracket and door bracket plate (2) asshown.1. Centre door bracket (with or without door bracket plate,

as required) at the top inside face of door as shown. Markholes.A. One-pi ece door sLocate bracket at inside face of the door 0-100mm down.B. Sect ional doors150 - 250mm below the top of the door.

2. Fasten bracket to the door using the appropriate screws.A. Wooden doorsDrill 8mm holes (5/16") and fasten the door bracket withnut, lock washer, and carriage bolt (3).B. Sheet meta l doorsFasten with metal screws (4).C. One-pi ece door opt ionalFasten with wood or metal screws (4).

12

A. 0-100mmB. 150-250mm

A

B

1

4C

12

3

3

1

2

412

19

2

124V/21W Max.Turn power off, then gently pull lens (2) downward until the

lens hinge is in the fully open position. Do not remove thelens. Install a 24V/21W maximum light bulb (1) in the socketas shown. Turn power on, the light will turn on and remain litfor 2-1/2 minutes. After 2-1/2 minutes it will turn off. To close,gently push diffuser up until engaged.

18

Connect Electri c PowerTO AVOID INSTALLATION DIFFICULTIES, DO NOT RUN THE GARAGE DOOR OPENER UNTIL INSTRUCTED TODO SO. Connect to properly fused and earthe d power outlet .

8

INSTALL LIGHT

FASTEN DOOR BRACKET

ASSEMBLE DOOR ARM

12

3

1

2

3

4

5

Travel limits regulate the points at which the door will stopwhen moving up or down. Follow the steps below to setthe limits.

NOTE: The door must be in the mid or close d positionto begin setting the limit s.

Setting the limits:1. Press and hold the black button (1) until the yellow

indicator (3) light starts flashing slowly then release.2. Adjust the position of the door to the desired UP

position by using the black button. Black (1) moves thedoor UP (open) and orange (2) moves the door DOWN(close). Check to be sure the door opens high enoughfor your vehicle to pass under.

3. Push the transmitter or door control. This sets the UP(open) limit and begins closing the door.Immedi ately press either the orange or the blackbutton. The door will stop.

4. Adjust the desired DOWN (close) limit position usingthe black and orange buttons. Check to be sure thedoor is fully closed without applying excessive pressureon the rail (rail should not bow upwards and the chainshould not sag or droop below the rail). Push thetransmitter or door control. This sets the DOWN (close)limit and begins opening the door.

5. Open and close the door with the transmitter or doorcontrol 2 or 3 times (leave door in open position readyfor force setting).

NOTE: The forc e must now be set in orde r tocomplete your installation (refer section 22).

21

2

2(2x)

3

4

The force setting button is loca ted behind the light lens of theopener . The force sett ing regulate s the amount of powerrequire d to open and clos e the door.

1. Open the light lens. Locate the orange button (2).2. Push the orange button (2) twice to enter unit into force

adjustment mode. The LED (3) (indicator light) will flash quickly.3. Push the programmed transmitter (4) or push bar on the door

control (if installed). The door will travel to the DOWN (close)position. Push the transmitter (4) again, the door will travel to theUP (open) position.

The LED (3) (indicator light) will stop flashing when the force hasbeen learned.The door must travel through a complete cycle, DOWN and UP, inorder for the force to be set properly. If the unit cannot open andclose your door fully, inspect your door to ensure that it is balancedproperly and is not sticking or binding.

The forc e MUST be learned in order to properly complete thesetting of the limits .

22

ADJUSTMENT SECTION

9

SETTING THE LIMITS

SETTING THE FORCE

Procedure : Place a 40mm obstacle (1) laid flat on the floor under the garage door. Operate the door in the downdirection. The door must reverse upon contact with the obstacle. If the door stops on the obstacle, removeobstacle and repeat setting the limits and force sections 21 & 22 and repeat safety reverse test.When the door reverses on the 40mm obstacle, remove the obstacle and run the opener through a completetravel cycle. Door must not reverse in closed position. If it does, repeat setting the limits and force sections 21 &22 and repeat safety reverse test.

Repeat test once a month and adjust as needed.

23

140mm

140mm

4. grey3. white

white wirestwisted together

white/blackwires twistedtogether

Connecting the Protect or Syst emTM

Locate the terminals on the front of the opener. Strip allwires back about 10mm then twist the two white wiresand the two white/black wires together. Trim the twistedwires to approximately 6mm. Use a small screwdriver orpen to hold down the spring terminals, insert thewhite/black wires into the grey terminal (4), thenterminate the white (only) wires into the white terminal(3).

Note: The opener wil l autom atically detect the Protec tor System TM when it is ins talled and opera ting for 5minute s (during this time the beams mus t remain unobs tructed). The opene r will not close unless thebeams are aligne d.

SAFETY FIRST!Whilst Chamberlain have engineered safety features into yourgarage door opener, we urge you to consider fitting IR Beamsto your new garage door opener. In many countries thesedevices are compulsory to prevent serious injury or propertydamage. For your own peace of mind and the safety of othersplease install this inexpensive safety device.

24

10

STANDARD INSTALLATION COMPLETE

Install this accessory for all insta llations on tiltdoors , doors over 2.5m and when the closing forc eas measured on the bot tom of the door is over400N (40kg).After opener has been installed and adjusted, theProtector Syst em™ accessory can be installed.Instructions are included with this accessory.The Protector System™ provides an additionalmeasure of safety against a small child or obstac lebeing caught under a garage door . It uses aninvisible beam which, when broken by an obstruction,causes a closing door to open and prevents an opendoor from closing and is strongly recommended forhomeowners with young children.

The safety reverse syst em test is important. The garage door mus t rever se on conta ct with a 40mmobs tac le laid flat on the floor. Failure to prope rly adju st opener may result in serious personal injuryfrom a clos ing garage door .

TEST THE SAFETY REVERSE SYSTEM

INSTALL THE PROTECTOR SYSTEM™(See accessori es)

The transmitters supplied with your opener are pre-programmed to your receiver in the factory.If you purchase additional transmitters, you will need to program them into your opener using the stepsbelow.Addin g transmi tters :Using the orange “LEARN” but ton :

1. Press and hold the button on the hand held transmitter you wish to program to the opener. The learn LED willflash continuously.

2. Press and release the orange “learn” button.3. Release the button on the hand held transmitter when the opener light flashes. It has learned the code. If the

light bulb is not installed, two clicks will be heard.Using the multi -function door con trol:1. Press and hold the button on the hand-held transmitter that you wish to operate your garage door.2. While holding the transmitter button, press and hold the LIGHT button on the multi-function door control.3. Continue holding both buttons while you press the push bar on the multi-function door control (all three

buttons are held).4. Release buttons when the opener light flashes. It has learned the code. If the light bulb is not installed,

two clicks will be heard.Deleting ALL trans mit ter codes

NOTE: This deletes all transmit ters and codesPress and hold the orange “learn” button on opener until the learn indicator light goes out (approximately 6seconds). All previous codes are now erased. Reprogram each transmitter or keyless entry you wish to use.

Activ ate the opener only when door is in full view, free of obstruc tion and properly adjusted. No oneshould enter or leave garage while door is in moti on. Do not allow chil dren to operate push button(s)or trans mitte r(s). Do not allow chil dren to play near the door.

11

1

3

2

4

LOCK LIGHT

LOCK LIGHT

1

3

2

25WIRELESS PROGRAMMING

1

2

1

3

4LOCKLIGHT

2

LOCKLIGHT

3

LOCKLIGHT

26

NOTE: Your new key less entr y must beprogrammed before it wi ll operate yourgarage door opener.

Program the keyless entry syst em

Using the orange “ LEARN” but ton:

1. Press and release the orange “learn” button (1)on opener. The learn indicator light will glowsteadily for 30 seconds.

2. Within 30 seconds, enter a four digit personalidentification number (PIN) of your choice onthe keypad (2), then press and hold theENTER button.

3. Release the button when the opener lightflashes (3). It has learned the code. If the lightbulb is not installed, two clicks will be heard.

.NOTE: This method requir es two peopl e if thekeyless entry is already mount ed outsi de thegarage.

Using the mu lti-function door control toprogram:

1. Enter a four digit personal identificationnumber (PIN) of your choice on the keypad,then press and hold ENTER.

2. While holding the ENTER button, press andhold the LIGHT button on the multi-functiondoor control.

3. Continue holding the ENTER and LIGHTbuttons while you press the push bar on themulti-function door control (all three buttonsare held).

4. Release buttons when the opener light flashes.It has learned the code. If the light bulb is notinstalled, two clicks will be heard.

Wireless fingerp rint access system C379(optional accessory)

Full instructions are available with this accessory.Once you have enrolled your user(s) into the C379you can program the unit into your opener.

Using the orange “LEARN” but ton:

1. Press and release the orange “learn” button onopener. The learn indicator light will glow steadily for30 seconds.

2. Within 30 seconds slide the cover of the C379 upas illustrated (A). Swipe your finger on the readerhead at a steady speed (B) until the yellow LEDturns on (C).

3. When the opener light flashes it has learned thecode. If the light bulb is not installed, two clicks willbe heard, ensure there are no obstructions in thepath of the door, then press the send button (D) totest the door.

Acti vate the opener only when door is in full view, free of obstruction and prope rly adjusted. No oneshoul d enter or leave garage while door is in motion. Do not allow children to opera te push but ton(s)or transmi tter( s). Do not allow chil dren to play near the door.

Programmi ng C379 wireless fingerprint

KEYLESS DEVICE PROGRAMMING (OPTIONAL ACCESSORIES)

12

ENROLL

FAIL

RETRY

SEND

PASS

READY

ENROLL

A

ENROLL

FAIL

RETRY

SEND

PASS

READY

ENROLL

C

B

D

Slide the cover plateup (A)

Swipe finger at asteady speed (B)

Yellow LED will indicatesuccessful swipe (C)

Courtesy light willflash once.

Test reader by pressingthe send button (D)

4

2

3

WHT-2

RED-1

6

6mm

1

2

4

WHTRED

1

4

LOCKLIGHT

3

3

2

3

Multi-function wall control

Backlit push button

Operat ion of the door contro l using the multi-function door contro l

Press the push bar (1) to open or close the door. Press again to stop the door.

Light featurePress the light button (2) to turn the opener light on or off, (it will not control theopener light when the door is in motion). If you turn it on and then activate the opener,the light will remain on for 2-1/2 minutes. Press again to turn it off sooner.Loc k featureDesigned to prevent operation of the door from hand-held transmitters. However, thedoor will open and close from the door control, the outside keyswitch and the keylessentry accessories.To activate, press and hold the lock button (3) for 2 seconds. The push bar light willflash as long as the lock feature is on.To turn off, press and hold the lock button again for 2 seconds. The push bar light willstop flashing. The lock feature will also turn off whenever the “LEARN” button on theopener panel is activated.

INSTALL DOOR CONTROL (OPTIONAL)27

Locate door contr ol wher e the garage door is visible, away from door and door hardware and out ofthe reach of chi ldre n. Mount at least 1.5 m (5 feet) above the floor.Serious persona l in jur y from a mov ing garage door may result from misus e of opener. Do not allowchil dren to oper ate the door cont rol or transmitte r.Permanentl y fasten the caution label to the wall near the door contr ol as a reminder of safe oper atingprocedure s.

LOCKLIGHT

1

2

3

13

Install ationThere are 2 terminals (1) on the back of the door control. Strip about 6mm (1/4") of insulation from bell wire (4).Separate wires enough to connect the white/red wire to RED terminal screw (1) and the white wire to WHT terminalscrew (2).Fasten the door control to an inside garage wall with sheet metal screws (3) provided. Drill 4mm (5/32") holes anduse anchors (6) if installing onto plasterboard wall. A convenient place is beside the service door and out of reachof children.Run the bell wire up the wall and across the ceiling and connect to the garage door opener quick connect terminalswhich are located behind the light lens of the opener. Connect the bell wire to the terminals as follows: white/red tored (1) and white to white (2).Use a screwdriver or pen to press open the spring terminals, then insert the cable intothe terminal.

A B8

7

6

5

A. Door withi n a door connect ionOpen light lens. Locate auxiliary quick connect terminals (remove factory installed link). Insert bell wire intoquick connect terminals 8 and 7.

B. Flashi ng light connect ionThe flashing light can be installed anywhere. Connect light leads to quick connect terminals 6 and 5. Terminal5 is ground.

28

8 97

32

5

4

LOCKLIGHT

6

1ENROLL

FAIL

RETRY

SEND

PASS

READY

ENROLL

29

1. Model C379 Fingerprint keyless entrypad

2. Model 84335AML 3 channel mini transmitter

3. Model 84330AML 1 channel transmitter

4. Model 8747AML keyless entry system

5. Model 770AML or C77 The Protector SystemTM

6. Model 845AML Multi-function control panel

7. Model 75AML Illuminated button

8. Model 760AML Outdoor keyswitch

9. Model 1702AML or CM1702 Outside quick release

14

SPECIAL FEATURES

ACCESSORIES

NOTICE

041A2828disengagement

rope and handle

178B0034Bstraight door

arm

178B0086Bcurved door arm012C0778

hanging bracket

chain links004A1008 1/2”109A0046 1”

083A0011-1grease

041A5643-19hardware bag

12VDC

Pb Cd Hg

012C0778brackets

041A5800outer trolley

012C0855header bracket

183D1077

183D0178

041A5887C-rail assembly

replacement batteries229A2032 (x1) or

229A2016 (x2)

041A6398inner trolley

repair kit

012C0777idler assembly

144C0077idler pulley

012C0810header sleeve

012B0905

012B0906

door bracket

door bracket

041B4103-1chain tensioner

041A5801chain kit

031D0536sprocket cover

REPLACEMENT PARTS30

15

041A5735Clogic board

lamp041A0079

041D0577motor assembly

002C1577cover & lens assembly

108C0082lens cover

041A5908 chassis

204C0240-2transformer and lead

041A5797 sprocket

158A0049 E circlip

16

31 REPLACEMENT PARTS

If the supply cord is damaged, it must be replaced by the manufacturer, its serviceagent or similarly qualified persons in order to avoid hazard.

TROUBLE SHOOTING1. Opener doesn't operate from either door control or transmitter:

• Does the opener have electric power? Plug lamp into outlet. If itdoesn't light, check the fuse box or the circuit breaker. (Some outletsare controlled by a wall switch.)

• Have you disengaged all door locks? Review installation instructionwarnings on page 1.

• Is there a build-up of ice or snow under door? The door may befrozen to ground. Remove any obstruction.

• The garage door spring may be broken. Have it replaced.2. Opener operates from transmitter but not from door control:

• Is door control button lit? If not, remove the bell wire from the openerterminals. Short the red and white terminals by touching bothterminals at the same time with a piece of wire. If the opener runs,check for a faulty wire connection at the door control, a short underthe staples, or a broken wire.

• Are wiring connections correct? Review section 27.3. Door operates from door control but not from transmitter:

• Replace battery if necessary.• If you have two or more transmitters and only one operates, review

wireless programming, keyless device programming sections 25 and26.

• Is the door control button flashing? The opener is in lock mode. If youhave a multi-function door control, push and hold the lock button for2 seconds. The door control button will stop flashing.

4. Transmitter has short range:

• Is battery installed? Check or change battery.• Change the location of the transmitter in the car.• A metal garage door, foil-backed insulation or metal siding will reduce

the transmission range.5. Door reverses for no apparent reason and opener light doesn'tflash:

• Is something obstructing the door? Pull manual release handle.Operate door manually. If it is unbalanced or binding, call forprofessional garage door service.

• Clear any ice or snow from garage floor area where garagedoor closes.

• Repeat setting limits and force, see adjustment sections 21 and 22.Repeat safety reverse test after adjustment is complete.6. Door reverses for no apparent reason and opener light flashesfor 5 seconds after reversing:

• Check the Protector System™ (if you have installed this accessory).If the light is flashing, correct alignment.

7. The garage door opens and closes by itself:

• Make sure transmitter push button is not stuck "on".8. Door stops but doesn't close completely:

• Repeat setting the limits, see adjustment section 21.• Repeat safety reverse test after any adjustment of door arm length,close force or down limit.9. Door opens but won't close:

• Check the Protector System™ (if you have installed this accessory).If the light is flashing, correct alignment.

• If opener light does not flash and it is a new installation, repeat settingthe limit and force sections 21 and 22.

• Repeat the safety reverse test after the adjustment is complete.10. Opener light does not turn on:

• Replace light bulb (24V/21W maximum).11. Opener strains:

• Door may be unbalanced or springs are broken. Close door and usemanual release rope and handle to disconnect trolley. Open and closedoor manually. A properly balanced door will stay in any point of travelwhile being supported entirely by its springs. If it does not, call forprofessional garage door service to correct the problem.

12. Opener motor hums briefly, then won't work:

• Garage door springs are broken. SEE ABOVE.• If problem occurs on first operation of opener, door is locked. Disable

door lock.• Repeat safety reverse test after adjustment is complete.13. Opener won't activate due to power failure:

• Pull manual release rope and handle down and back to disconnecttrolley. Door can be opened and closed manually. When the power isrestored, pull the manual release handle straight down. The next timethe opener is activated, the trolley will reconnect.

• The outside quick release accessory (if fitted) disconnects the trolleyfrom outside the garage in case of power failure.

14. Setting the limits manually:

1.Press and hold the black button until the yellow indicator light startsflashing slowly then release.

2.Push and hold the black button until the door reaches the desired UP(open) position. Adjust the position of the door by using the black andorange buttons. Black moves the door UP (open) and orange movesthe door DOWN (close).

Check to be sure the door opens high enough for your vehicle.

3.Push the transmitter or door control. This sets the UP (open) limit andbegins closing the door. Immediately press either the orange orthe black button. The door will stop.

Adjust the desired DOWN (closed) limit by using the orange (DOWN)and black (UP) buttons. Check to be sure the door is fully closedwithout applying excessive pressure on the rail (rail should not bowupwards and the belt should not sag or droop below the rail). Pushthe transmitter or door control. This sets the DOWN (close) limit andbegins opening the door.

NOTE: If neither the BLACK or the ORANGE button is pressed, thedoor will reverse off the floor and the DOWN travel limit will be setautomatically.

4.Open and close the door with the transmitter or door control 2or 3 times.

• If the door does not stop in the desired UP (open) position or reversesbefore the door stops at the DOWN (close) position, repeat settingthe limits manually one more time.

• If the door stops in both the desired UP (open) and DOWN (close)positions, proceed to test the safety reversal system.

17

MAINTENANCE OF YOUR OPENEROnce a Year:• Apply grease to rail and trolley• Oil door rollers, bearings and hinges• DO NOT lubricate the opener itself• DO NOT APPLY grease to the door tracks

CARE OF YOUR OPENERWhen properly installed, your opener will operate with minimalmaintenance. The opener does not require additional lubrication.

Limit and force settings: These settings must be checked andproperly set when opener is installed. Weather conditions may causesome minor changes in the door operation, requiring somere-adjustments, particularly during the first year of operation.Refer to setting the limits and force on page 9. Follow the instructionscarefully and repeat the safety reverse test after any adjustment.Transmitter: The transmitter may be secured to a car sun visor withthe clip provided. Additional transmitters can be purchased at anytime for use in all vehicles using garage. Refer to accessories. Anynew transmitters must be programmed into the opener.Transmitter battery: If transmission range decreases, replacebattery.To change battery: To replace batteries, use the visor clip orscrewdriver blade to pry open the case. Insert batteries positive sideup. To replace cover, snap shut along both sides. Do not dispose ofthe old battery with household waste. Take batteries to a properdisposal centre.

OPERATION OF YOUR OPENERYour opener can be activated by any of the following devices:

• The backlit door control button (if installed). Hold the buttondown until door starts to move.

• The outside keyswitch or keyless entry system (if you haveinstalled either of these accessories).

• The transmitter. Hold the push button down until the door starts tomove.Opening the door manually:

The door can be opened manually by pulling the release handledown. To reconnect the door, pull the release handle down andtoward the opener.Do not use the manual release handle to pull the door openor closed.When the opener is activated by transmitter or backlit doorcontrol button:1. If open, the door will close. If closed, the door will open.2. If closing, the door will stop.3. If opening, the door will stop (allowing space for entry and exit of

pets and for fresh air).4. If the door has been stopped in a partially open or closed position,

it will reverse direction.5. If an obstruction is encountered while closing, the door will

reverse.6. If an obstruction is encountered while opening, the door will

reverse, then stop.7. The optional Protector System™ uses an invisible beam which,

when broken by an obstruction, causes a closing door to openand prevents an open door from closing. It is STRONGLYRECOMMENDED for homeowners with young children.

Allow a 15 minute cooling period after 5 continuous operationsof the opener.

The opener light will turn on:1. when opener is initially plugged in;2. when the power is briefly interrupted;3. when the opener is activated.The light turns off automatically after 2-1/2 minutes. Bulb size is24V/21W maximum.

SPECIFICATIONSInput Voltage 230-240 VAC, 50Hz

Max. Pull Force ..............600NPower .............................115WStandby Power ...............5.5WNormal Torque ................7Nm

MotorType................................DC gearmotor permanent lubricationDrive MechanismDrive ...............................Chain with two-piece trolley on

steel railLength of Travel..............1.1m to 2.3mTravel Rate .....................127-178mm per secondLamp...............................On when door starts, off 2-1/2 minutes

after stopDoor Linkage ..................Adjustable door arm. Pull cord trolley releaseSafetyPersonal .........................Push button and automatic stop in down

direction. Push button and automatic stop inup direction

Electronic ........................Automatic force adjustmentElectrical .........................Transformer overload protector and low

voltage push button wiringLimit Device ....................Optical RPM/Passpoint detectorLimit Adjustment .............Electronic, semi and fully automaticStart Circuit.....................Low voltage push button circuitDimensionsLength (Overall)..............3.2mHeadroom Required .......30mmHanging Weight ..............16kgReceiverMemory Registers ..........12Operating Frequency......433.92MHz

18

Door should be fully closed if possible. Weak or brokensprings could allow an open door to fall rapidly. Propertydamage or serious personal injury could result.

SPECIAL NOTE: Chamberlain strongly recommends that the Protector SystemTM be installed on all garage door openers.

Liability – Australia onlyUnder no circumstances shall the Seller be liable for consequential,incidental or special damages arising in connection with the use, orinability to use, the Unit. In no event shall the Seller's liability fordamages or injury arising from breach of law or contract or fornegligence, exceed the cost of repairing or replacing the Unit orrefunding the purchase price of the Unit.

Under Division 2 Part V of the Trade Practices Act, 1974, certainwarranties and conditions (Implied Terms) are implied into contractsfor the supply of goods or services if the goods or services are of akind ordinarily acquired for personal, domestic or household use orconsumption. Liability for breach of those Implied Terms cannot beexcluded or limited and the limitations and exclusions above do notapply to the Implied Terms.

Except for the Implied Terms and the warranties set out above, theSeller excludes all warranties and conditions implied by statute, atlaw, in fact or otherwise.

Liability – New Zealand onlyExcept as set out in the Fair Trading Act 1986 and the ConsumerGuarantees Act 1993:

(a) all other guarantees, warranties and representations inrelation to the Unit or its supply are excluded to the extentthat the Seller can lawfully exclude them; and(b) under no circumstances shall the Seller be liable forconsequential, incidental or special damages arising inconnection with the use, or inability to use, the Unit, other thanthose which were reasonably foreseeable as liable to result from thefailure.

NOTE: We request that you attach your sales docket or invoiceto this manual to enable you to establish the date of purchasein the unlikely event of a service call being made.Chamberlain reserves the right to change the design andspecification without prior notification. Some features oraccessories may not be available in certain markets or areas.Please check with your distributor.

CONTACT DETAILS:

Chamberlain service centres:AustraliaPhone toll free 1800 638 234Fax toll free 1800 888 121

New ZealandAuckland phone 09 477 2823Phone toll free 0800 653 667Fax toll free 0800 653 663

www.chamberlainanz.com.au

CHAMBERLAIN 1 YEAR LIMITED WARRANTYChamberlain ML700Sectional Door Opener

Chamberlain Australia Pty Limited / Chamberlain New ZealandLimited (Seller) warrants to the original purchaser of theChamberlain ML700 Sectional Door Opener (Unit) that it is freefrom defects in material and/or workmanship for a period of 1year from the date of first purchase from the Seller.

Please retain your proof-of-purchase in the unlikely event yourequire warranty service.

If, during the limited warranty period, the Unit fails due to defects inmaterials or workmanship Chamberlain will, provided the defectivepart or Unit is returned freight and insurance prepaid and wellpackaged to the nearest Chamberlain office or authorised installer,undertake to repair or, at its option, replace any defective part orUnit and return it to the Buyer at no cost. Repairs and replacementparts are warranted for the remaining portion of the original warrantyperiod.

Limited warranty on openerChamberlain will furnish a replacement opener free of charge, if it isfound to be defective. Labour costs may apply.Where the Unit has been installed by an authorised installer,Chamberlain will furnish replacement parts free of charge throughthe authorised installer. A service fee for on-site service may apply.

In-warranty serviceDuring the warranty period, if the product appears as though it maybe defective, call our toll free service before removal of the Unit. AChamberlain technician will diagnose the problem and promptlysupply you with the parts for “do-it-yourself” repairs, or provide youwith shipping instructions for a factory repair or replacement. If anauthorised installer installed your Unit you must call them for prompton-site service.

If our service centre determines that a warranty claim has beenmade in respect of a failure or defect arising out of any exclusiondetailed below, we may charge you a fee to repair and/or return theUnit to you.

ExclusionsThis warranty does not cover any failure of the Unit due to:1.non-compliance with the instructions regarding installation,operation, maintenance and testing of the Unit or of any productwith which the Unit is used.2.any attempt to repair, dismantle, reinstall or move the Product toanother location once the Product is installed by any person otherthan an authorised installer.3.tampering, neglect, abuse, wear and tear, accident, electricalstorm, excessive use or conditions other than normal domestic use.This warranty does not cover any problems with, or relating to, thegarage door or garage door hardware, including but not limited tothe door springs, door rollers, door alignment or hinges, anyproblems caused by electrical faults, replacement of batteries orlight bulbs or labour charges for reinstalling a repaired or replacedUnits.

114A4219B © 2010 The Chamberlain Group, Inc

19

TM Trademark of The Chamberlain Group, Inc.® Registered Trademark of The Chamberlain Group, Inc.