Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
Export Sales Department phone +48 68 47 90 832, 951 • e-mail: [email protected]
1
RM84miniature relays
2 CO, 2 NO ❷AgNi, AgNi/Au hard gold plating, AgSnO2
250 V / 400 V5 V AgNi, 5 V AgNi/Au hard gold plating, 10 V AgSnO2
8 A / 250 V AC 3 A / 120 V 1,5 A / 240 V (B300) 8 A / 24 V DC (see Fig. 3) 0,22 A / 120 V 0,1 A / 250 V (R300)1/3 HP 240 V AC, 3,6 FLA, single-phase motor ❸
0,37 kW 240 V AC, single-phase motor5 mA AgNi, 2 mA AgNi/Au hard gold plating, 10 mA AgSnO2
15 A AgSnO2
8 A2 000 VA0,3 W AgNi, 0,05 W AgNi/Au hard gold plating, 1 W AgSnO2
600 cycles/hour 72 000 cycles/hour
12, 24, 48, 60, 110, 115, 120, 220, 230, 240 V 3, 5, 6, 9, 12, 18, 24, 36, 48, 60, 110 V AC: n DC: n
see Tables 1, 2 and Fig. 4, 50,75 VA 0,4 ... 0,48 W
400 V AC4 000 V 1,2 / 50 μsIII3V-0 for standard cover (no transparent), UL 945 000 V AC type of insulation: reinforced 1 000 V AC type of clearance: micro-disconnection 2 000 V AC contacts 2 NO, type of clearance: full-disconnection ❷ 2 500 V AC type of insulation: basicclearance: creepage:
7 ms / 3 ms> 105 8 A, 250 V AC see Fig. 2 > 105 0,15 A, 220 V DC> 3 x 107
29 x 12,7 x 15,7 mm / 14 g-40...+85 oC AC: -40...+70 oC DC: -40...+85 oC -20...+70 oC ❶IP 40 ❶ or IP 67 EN 60529RTII ❶ or RTIII EN 61810-720 g10 g / 5 g 10...150 Hzmax. 270 oC max. 5 s
Contact dataNumber and type of contactsContact materialRated / max. switching voltage ACMin. switching voltageRated load (capacity) AC1 AC15 DC1 DC13Motor load acc. to UL 508 AC3 acc. to IEC 60947-4-1Min. switching currentMax. inrush currentRated currentMax. breaking capacity AC1Min. breaking capacityContact resistanceMax. operating frequency • at rated load AC1 • no loadCoil dataRated voltage 50/60 Hz AC DCMust release voltageOperating range of supply voltageRated power consumption AC DCInsulation according to EN 60664-1Insulation rated voltageRated surge voltageOvervoltage category Insulation pollution degreeFlammability class Dielectric strength • between coil and contacts • contact clearance • pole - poleContact - coil distanceGeneral dataOperating / release time (typical values)Electrical life • resistive AC1
• DC L/R=40 msMechanical life (cycles)Dimensions (L x W x H) / Weight Ambient temperature • storage (non-condensation and/or icing) • operatingCover protection categoryEnvironmental protection Shock resistanceVibration resistance (NO/NC)Solder bath temperature Soldering time
• CTI 250 • Reinforced insulation• For PCB and plug-in sockets • AC and DC coils, insulation class F: 155 °C• Available special versions: in transparent cover ❶;
with the increased dielectric strength of the contact clearance ❷ • Compliance with standards EN 60335-1, EN 45545-2RoHS,
The data in bold type relate to the standard versions of the relays. ❶ Special versions - relays in transparent cover , only available with IP 40 and RTII, operating temperature -20...+70 °C. See ”Ordering codes”. ❷ Special versions - relays with two normally open contacts 2 NO, with increased contact gap - dielectric strength 2000 V AC, only available with DC coils. See ”Ordering codes”. ❸ For single phase motors for 110-120 V AC do not use motors with higher FLA than given for 240 V AC.
RM84-...-01 (AC) ❶RM84 RM84-...-01 (DC) ❶
23
.12
.20
20
Export Sales Department phone +48 68 47 90 832, 951 • e-mail: [email protected]
2
RM84miniature relays
Connection diagrams (pin side view)
Terminal (pin) A1(1); A2(2) 22(3); 21(4); 24(5);12(6); 11(7); 14(8)
[mm] Ø 0,6 0,5 x 0,9
Drilling hole:• for relays Ø 1,3 + 0,1 mm• for sockets Ø 1,5 + 0,1 mm
2 CO 2 NO
Dimensions
5 15,2
29
12,7
7,5
3,9
15,7
2,5
12,7
5 15,7
3,9
Pinout (solder side view)
2 CO 2 NO
8 × Ø 1,3 2,5
5 5 15,2
2,5
2,5
6 × Ø 1,3 2,5
5 2,520,2
2,5
Mounting, sockets and accessories for relays
Sockets for RM84
AccessoriesAdditional equipment
Retainer / retractor clips
Spring wire clips
Description plates
Screw terminals sockets, 35 mm rail mount (acc. to EN 60715) or on panel mounting (one M3 screw)GZT80 GZT80-0040 GZM80-0041 GZT80-0035 M... ❻, ZGGZ80 ❼GZM80 GZT80-0040 GZM80-0041 GZT80-0035 M... ❻, ZGGZ80 ❼GZS80 GZS-0040 GZM80-0041 TR M... ❻, ZGGZ80 ❼GZF80 – GZM80-0041 – –
Push-in terminals sockets, 35 mm rail mount (acc. to EN 60715) or on panel mounting (one M3 screw)
GZP80 ❺ GZP80-0400, GZT80-0040 GZM80-0041 MP15 M... ❻, ZGZP80-8,
ZGZP80-2, ZGZP-2 ❼Sockets for PCB
PW80 – MH16-2 – –EC 50 – MP16-2 ❽, MH16-2 – –
GD50 – MP16-2 ❽, MH16-2, GD-0016 – –
❹ For relays in transparent cover: the distance at least 5 mm between the relays mounted side by side. ❺ Sockets GZP80: wire connection - see page 7. ❻ Signalling / protecting modules type M... - see page 10. ❼ Interconnection strips ZGGZ80, ZGZP... - see page 11-12. ❽ Plastic clips MP16-2.
Relays RM84 ❹ are designed for: • direct PCB mounting • plug-in sockets.
23
.12
.20
20
Export Sales Department phone +48 68 47 90 832, 951 • e-mail: [email protected]
3
RM84miniature relays
DC1
In = 8 A
AC1
N - electrical life at AC1
23
.12
.20
20
Export Sales Department phone +48 68 47 90 832, 951 • e-mail: [email protected]
4
RM84miniature relays
The data in bold type relate to the standard versions of the relays.
Coil data - AC 50/60 Hz voltage version Table 2
Coil operating rangeV AC 50 Hz
9,619,238,448,088,092,096,0
176,0184,0192,0
13,228,857,672,0
132,0138,0144,0264,0276,0288,0
min. (at 20 °C) max. (at 20 °C)± 10%± 10%± 10%± 10%± 10%± 10%± 10%± 10%± 10%± 15%
Acceptableresistance
The data in bold type relate to the standard versions of the relays.
2,13,54,26,38,4
12,616,825,233,642,077,0
7,612,715,322,930,645,961,291,8
122,4153,0280,0
± 10%± 10%± 10%± 10%± 10%± 10%± 10%± 10%± 10%± 10%± 10%
Rated voltageV AC
Coil resistanceat 20 °C Coil code
5012502450485060511051155120522052305240
12244860
110115120220230240
100400
1 5502 6008 9009 600
10 20035 50038 50042 500
10031005100610091012101810241036104810601110
3569
121824364860
110
226090
200360710
1 4403 1405 7007 500
25 200
Coil data - DC voltage version Table 1
Coil operating range V DC
min. (at 20 °C) max. (at 20 °C)
Acceptableresistance
Rated voltageV DC
Coil resistanceat 20 °C Coil code
Interface relays PI84 (PI85)
set: relay RM84 (RM85) + socket GZT80 (GZM80, GZP80)
23
.12
.20
20
Export Sales Department phone +48 68 47 90 832, 951 • e-mail: [email protected]
5
RM84miniature relays
Ordering codes
Examples of ordering code:
RM84-3012-25-5024 relay RM84, for PCB and sockets, two changeover contacts, contact material AgSnO2, coil voltage 24 V AC 50/60 Hz, in standard cover (no transparent) IP 40
RM84-2012-25-1012-01 relay RM84, for PCB and sockets, two changeover contacts, contact material AgNi, coil voltage 12 V DC, in transparent cover (blue colour) IP 40
RM84-2322-35-1024 (51) relay RM84, special version with increased contact gap, for PCB and sockets, two normally open contacts, contact material AgNi/Au hard gold plating, coil voltage 24 V DC, in standard cover (no transparent) IP 67
R M 8 4 — — —
Cover
without marks - standard cover (no transparent)01 - transparent cover IP 40 (orange colour - AC coils, blue colour - DC coils) ❶
—
Contact material
20 - AgNi23 - AgNi/Au hard gold plating30 - AgSnO2
Number and type of contacts
12 - 2 CO22 - 2 NO
Cover protection category
2 - in cover, IP 40 version3 - in cover, IP 67 waterproof version
Connection mode
5 - for PCB and sockets
Special version
without marks - basic version, dielectric strength of contact clearance 1000 V AC(51) - contacts 2 NO, increased contact gap - dielectric strength 2000 V AC ❷
Type Contact material
Number and type of contacts
Cover protection category
Connection mode
Coil code Cover Special version
see Tables 1, 2 page 4
❶ 01: special version - relay in transparent cover , only available with IP 40 and RTII, operating temperature -20...+70 °C ❷ (51): special version - relay with two normally open contacts 2 NO, with increased contact gap - dielectric strength 2000 V AC, only available with DC coil
RM84
Transparent cover IP 40,
(orange colour - AC coils, blue colour - DC coils)
23
.12
.20
20
Export Sales Department phone +48 68 47 90 832, 951 • e-mail: [email protected]
6
Sockets and accessories
778
,1
42,524
61-0,267
35,3
21,5
24
32,1
Ø 3
,2
7,5
205
5
81,6
-0,2
15,9-0,2
775
,3±0
,15
42,524
61-0,267
35,2
19,8
42,5
Ø 3
,2
7,5
205
5
80-0
,2
29,8
15,6-0,2
GZT80For RM84, RM85, RM85 inrush, RM85 105 °C sensitive, RM87L, RM87L sensitive,RM87P, RM87P sensitive
Screw terminals Max. tightening moment for the terminal: 0,7 Nm35 mm rail mount acc. to EN 60715 or on panel mounting 80 x 15,6 x 61(67) mm ❷Two poles, 5 mm pinout 12 A, 300 V AC
DimensionsConnection diagrams ❸
Accessories ❶
GZM80For RM84, RM85, RM85 inrush, RM85 105 °C sensitive, RM87L, RM87L sensitive,RM87P, RM87P sensitive
Screw terminals Max. tightening moment for the terminal: 0,7 Nm35 mm rail mount acc. to EN 60715 or on panel mounting 81,6 x 15,9 x 61(67) mm ❷Two poles, 5 mm pinout 12 A, 300 V AC
DimensionsConnection diagrams ❸
Accessories ❶
GZS80For RM84, RM85, RM85 inrush, RM85 105 °C sensitive, RM87L, RM87L sensitive,RM87P, RM87P sensitive
Screw terminals Max. tightening moment for the terminal: 0,5 Nm35 mm rail mount acc. to EN 60715 or on panel mounting 76,8 x 15,8 x 42,5(57,1) mm ❷Two poles, 5 mm pinout 10 A, 300 V AC
DimensionsConnection diagrams ❸
Accessories ❶
ZGGZ80
GZT80-0040 GZT80-0035 Module type M...
GZM80-0041
GZT80-0040 GZT80-0035 Module type M...
GZM80-0041ZGGZ80
GZM80-0041
Module type M...TR
ZGGZ80
GZS-0040
NC
COM
NO
COIL
RM84 RM87L RM87PRM85 RM85 inrush RM85 105 °C sensitive
NC
NO
COIL
RM84 RM87L RM87PRM85 RM85 inrush RM85 105 °C sensitive
RM84 RM87L RM87PRM85 RM85 inrush RM85 105 °C sensitive
NC
NO
COIL
COM
COM
❶ Mounting and sub-assemblies of accessories in the socket - see page 8. Signalling / protecting modules type M... - see page 10. ❷ In the bracket the height of socket with retainer / retractor clip is shown. ❸ For RM85..., RMP85: loads above 12 A (GZT80, GZM80, GZP80) or 10 A (GZS80, GZF80) require bridging pairs of terminals: 11 with 21, 12 with 22, 14 with 24 - see www.relpol.com.pl
23
.12
.20
20
Export Sales Department phone +48 68 47 90 832, 951 • e-mail: [email protected]
7
Sockets and accessories
21(4) 21(4) 21(4) 21(4) 21(4)
24(5) 24(5) 24(5) 24(5) 24(5)
22(3) 22(3) 22(3) 22(3) 22(3)
14(8) 14(8) 14(8) 14(8) 14(8)
12(6) 12(6) 12(6) 12(6) 12(6)
A1(1)A2(2) A1(1)A2(2) A1(1)A2(2) A1(1)A2(2) A1(1)A2(2)
21(4)
24(5)
22(3)
11(7) 11(7) 11(7) 11(7) 11(7)11(7)
14(8)
12(6)
A1(1)A2(2)
GZP80For RM84, RM85, RM85 inrush, RM85 105 °C sensitive, RM87L, RM87L sensitive,RM87P, RM87P sensitive,RMP84, RMP85
Push-in terminals Max. cross section of the cables: 2 x 1,5 mm2 (ferrules without insulation) 2 x 1 mm2 (ferrules with insulation) Stripping length: 8...10 mm
35 mm rail mount acc. to EN 60715 or on panel mounting 97 x 15,9 x 45,9(75,8) mm ❷5 mm pinout One pole 12 A, 300 V AC Two poles 8 A, 300 V AC
DimensionsConnection diagrams ❸
Accessories ❶ Wire connection
RM84 RMP84
RM87L RM87PRM85RMP85
RM85 inrush RM85 105 °C sensitive
45,975,8
27,9
29,8
35,2
92,9
15,9
97
NC
NO
COIL
COM
ZGZP80-8
The drawings present inserting wire into the Push-in terminal and removing wire using the button releasing a clamp (assembly without tools).
GZP80-0400 Module type M...GZT80-0040 GZ80-1001GZM80-0041 MP15 ZGZP80-2 ZGZP-2
67,2
21,86,815,53,5
23,210,5
26,7
35,4
13,3
18,5
36,5
2738
Ø 3
,5
205
5
GZF80For RM84, RM85, RM85 inrush, RM85 105 °C sensitive, RM87L, RM87L sensitive,RM87P, RM87P sensitive,RMP84, RMP85
Screw terminals Max. tightening moment for the terminal: 0,5 Nm35 mm rail mount acc. to EN 60715 or on panel mounting 67,2 x 15,5 x 36,5 mmTwo poles, 5 mm pinout 10 A, 250 V AC
DimensionsConnection diagrams ❸
Accessories
RM84 RMP84
RM87L RM87PRM85RMP85
RM85 inrush RM85 105 °C sensitive
NC
NO
COIL
COM
GZ80-1001GZM80-0041
❶ Mounting and sub-assemblies of accessories in the socket - see page 8. Signalling / protecting modules type M... - see page 10. ❷ In the bracket the height of socket with retainer / retractor clip is shown. ❸ For RM85..., RMP85: loads above 12 A (GZT80, GZM80, GZP80) or 10 A (GZS80, GZF80) require bridging pairs of terminals: 11 with 21, 12 with 22, 14 with 24 - see www.relpol.com.pl
23
.12
.20
20
Export Sales Department phone +48 68 47 90 832, 951 • e-mail: [email protected]
8
Sockets and accessories
Screw terminals plug-in socket
Retainer / retractor clip
Signalling / protecting module type M...
Electromagnetic relay
Description plate
Removing the relay from the socket with a retrainer / retractor clip
Mounting and sub-assemblies of the relay and accessories in the socket
PRECAUTIONS: 1. the product in circumstances which exceed the parameters of the product. 2. 3. Ensure that the product has been connected
4. In case of any risk of any serious material loss or death or injuries 23
.12
.20
20
Export Sales Department phone +48 68 47 90 832, 951 • e-mail: [email protected]
9
Sockets and accessories
PW80For RM84, RM85, RM85 inrush, RM85 105 °C sensitive, RM87L, RM87L sensitive,RM87P, RM87P sensitive, RM83
For PCB34,6 x 12,9 x 6,6 mmTwo poles, 5 mm pinout 12 A, 250 V AC
Dimensions
Accessories
Pinout
EC 50For RM84, RM85, RM85 inrush, RM85 105 °C sensitive, RM87L, RM87L sensitive,RM87P, RM87P sensitive, RM83, RMP84, RMP85
For PCB 31,3 x 12,7 x 9 mmTwo poles, 5 mm pinout 12 A, 250 V AC
Accessories
DimensionsPinout
MH16-2
MH25-2
MP16-2
MP25-2
MH16-2 MH25-2
GD50For RM84, RM85, RM85 inrush, RM85 105 °C sensitive, RM87L, RM87L sensitive,RM87P, RM87P sensitive, RM83, RMP84, RMP85
For PCB31,5 x 13 x 9 mmTwo poles, 5 mm pinout 8 A, 300 V AC
Dimensions
Accessories
Pinout
GD-0016MH16-2
MH25-2
MP16-2
MP25-2
23
.12
.20
20
Export Sales Department phone +48 68 47 90 832, 951 • e-mail: [email protected]
10
Signalling / protecting modules type M...
MODULE type M...
LED red – M...R
LED green – M...G
❶ M...R - LED red, M...G - LED green❷ When ordering modules indicate their color: gray or black.
M21P
M31R, M31G M32R, M32G M33R, M33G
M51 M52 M53
M21N
Module D (polarization P)It limits overvoltage on DC coils.
Module LD (polarization P)It limits overvoltage on DC coils. Coil energizing indication.
Module LD (polarization N)It limits overvoltage on DC coils. Coil energizing indication.
Module RCIt protects against EMC disturbance.It limits overvoltage.
Module D (polarization N)It limits overvoltage on DC coils.
M41R, M41G M42R, M42G M43R, M43G
Module LCoil energizing indication.
Module VIt limits overvoltage on AC coils.No indication.
M61R, M61G M62R, M62G M63R, M63G
Module LVIt limits overvoltage on AC and DC coils.Coil energizing indication.
M91R, M91G M92R, M92G M93R, M93G
M71 M72 M73
Module RIt limits harmful voltage on AC coils induced in long lines which causes unwanted making of the relay.
M103
VoltageModules type M... Layout Type of module ❶ ❷
For sockets type: GZT80, GZM80, GZS80, GZP80, GZT92, GZM92, GZS92, ES 32, GZT2, GZM2, GZT3, GZM3, GZT4, GZM4, GZP4
Modules type M... are parallely connected with relay coil. Polarization P: -A1/+A2. Polarization N: +A1/-A2.
6/230 V DC
6/24 V DC 24/60 V DC
110/230 V DC
6/24 V AC/DC 24/60 V AC/DC
110/240 V AC/DC
6/230 V DC
6/24 V DC 24/60 V DC
110/230 V DC
6/24 V AC/DC 24/60 V AC/DC
110/240 V AC/DC
6/24 V AC/DC 24/60 V AC/DC
110/240 V AC/DC
6/24 V AC 110/130 V AC 220/240 V AC110/240 V AC
23
.12
.20
20
Export Sales Department phone +48 68 47 90 832, 951 • e-mail: [email protected]
11
Interconnection strips ZGGZ80
❸ Interface relay PI84 (PI85 set: electromagnetic relay RM84 (RM85) + plug-in socket GZT80 or GZM80 + signalling / protecting module type M... + retainer / retractor clip GZT80-0040 + description plate GZT80-0035. ❹ Also versions RM87. sensitive
Interconnection strip ZGGZ80
• designed for the co-operation with plug-in sockets of miniature relays and with interface relays PI84 and PI85, which are equipped with screw terminals; sockets and relays are mounted on 35 mm rail mount acc. to EN 60715,
• bridges common input signals (coil terminals A1 or A2) or output signals - see photo at the top,
• maximum permissible current is 10 A / 250 V AC,
• possibility of connection of 8 sockets or relays,
• colours of strips: ZGGZ80-1 grey, ZGGZ80-2 black.
ZGGZ80 for:
PI85-...-MS-... (RM85 + GZM80)
ZGGZ80
Relays for plug-in sockets
RM84, RM85, RM85 inrush, RM85 105 °C sensitive, RM87L ❹, RM87P ❹,
RM87N ❹
RM96 1 CO
Plug-in sockets
GZT80GZM80GZS80GZT92GZM92GZS92ES 32
Interface relays ❸
PI84-...-TS-... (RM84 + GZT80)
PI84-...-MS-... (RM84 + GZM80)
PI85-...-TS-... (RM85 + GZT80) (RM85 inrush + GZT80)
PI85-...-MS-... (RM85 + GZM80)
23
.12
.20
20
Export Sales Department phone +48 68 47 90 832, 951 • e-mail: [email protected]
12
Interconnection strips ZGZP...
❺ Interface relay PI84 (PI85, PI84P, PI85P set: electromagnetic relay RM84 (RM85, RMP84, RMP85) + plug-in socket GZP80 M... + retainer / retractor clip GZP80-0400. ❹ Also versions RM87. sensitive
Interconnection strips ZGZP...
- designed for the co-operation with plug-in sockets of miniature relays and with interface relays PI84, PI85, PI84P, PI85P, which are equipped with Push-in terminals; sockets and relays are mounted on 35 mm rail mount acc. to EN 60715,
- strip ZGZP80-8 bridges common input signals (coil terminals A1 or A2), maximum permissible current is 10 A / 250 V AC, possibility of connection of 8 sockets or relays,
ZGZP... for: Relays for plug-in sockets
RM84, RM85, RM85 inrush, RM85 105 °C sensitive, RM87L ❹, RM87P ❹,
RMP84, RMP85
Plug-in sockets
GZP80
Interface relays ❺
PI84-...-PS-... (RM84 + GZP80)
PI85-...-PS-... (RM85 + GZP80)
PI84P-...-PS-... (RMP84 + GZP80)
PI85P-...-PS-... (RMP85 + GZP80)
PI85-...-PS-... (RM85 + GZP80)
ZGZP-2 ZGZP80-2
ZGZP80-8
ZGZP80-2
ZGZP80-8 GY grey ZGZP80-8 BK black ZGZP80-8 RD red ZGZP80-8 BE blue
- strip ZGZP80-2 bridges common input signals (coil terminals A1 or A2) or output signals, possibility of connection of 2+n sockets or relays,
ZGZP80-2 GY grey ZGZP80-2 BK black ZGZP80-2 RD red ZGZP80-2 BE blue
- jumper ZGZP-2 bridges the neighboring poles of single socket GZP80.
ZGZP-2 GY grey ZGZP-2 BK black ZGZP-2 RD red ZGZP-2 BE blue
23
.12
.20
20