Mini Hi-FiComponentSystem

©1996 by Sony Corporation

Operating Instructions

3-859-544-12(1)

f

MHC-RX90

2

WARNINGTo prevent fire or shock hazard, do notexpose the unit to rain or moisture.

To avoid electrical shock, do not open the cabinet.Refer servicing to qualified personnel only.

Do not install the appliance in a confined space,such as a bookcase or built-in cabinet.

Laser component in this product is capable ofemitting radiation exceeding the limit for Class 1.

This caution label is located inside the unit.

This appliance is classifiedas a CLASS 1 LASERproduct. The CLASS 1LASER PRODUCTMARKING is located onthe rear exterior.

This stereo sytem is equipped with the Dolby* B-type noise reduction system.* Dolby noise reduction manufactured under licencefrom Dolby Laborotories Licencing Corporation.“DOLBY” and the double-D symbol a aretrademarks of the Dolby Laborotories LicencingCorporation.

GB

3

Table of Contents

Getting Started

Step 1: Hooking up the system ............ 4

Step 2: Setting the time ......................... 6

Step 3: Presetting radio stations .......... 7

Connecting optional AV components . 8

Basic Operations

Playing a CD ......................................... 11

Recording a CD .................................... 13

Listening to the radio ........................... 14

Recording from the radio .................... 15

Playing a tape ........................................ 16

Recording from a tape ......................... 18

The CD Player

Using the CD display ........................... 19

Playing the CD tracks repeatedly ...... 19

Playing the CD tracks in randomorder ................................................ 20

Programming the CD tracks ............... 21

Playing CDs without interruption ..... 22

The Tape Deck

Recording on a tape manually ........... 23

Recording a CD by specifying trackorder ................................................ 24

DJ Effects

Looping part of a CD ........................... 26

Flashing part of a CD ........................... 26

Waving the equalizer ........................... 27

Using the drum pads ........................... 27

Using the beat function ....................... 28

Sound Adjustment

Adjusting the sound ............................ 29

Selecting the audio emphasis ............. 30

Adjusting the audio emphasis ............ 31

Making a personal audio emphasisfile .................................................... 33

Switching the speaker formation ....... 34

Other Features

Using the Radio Data System (RDS)* 36

Singing along: Karaoke ...................... 38

Falling asleep to music ........................ 39

Waking up to music ............................. 40

Timer-recording radio programmes.. 41

Additional Information

Precautions ............................................ 43

Troubleshooting ................................... 44

Specifications ........................................ 47

Index ....................................................... 49

* For Western European model only

4

1

12

13

4

1

1

Step 1: Hooking up the systemDo the following procedure 1 to 4 to hook up your system using the supplied cords andaccessories.

Getting Started

2 Connect the speaker cords ofsurround speakers to the SURROUNDSPEAKER jacks of the same colour .

Keep the speaker cords away from theaerials to prevent noise.

Connect the speakers.1 Connect the speaker cords of front

speakers to the SPEAKER jacks of thesame colour .

Keep the speaker cords away from theaerials to prevent noise.

1

AM loop aerial

Front speaker(Left)

Front speaker(Right)

Surround speaker (Right) Surround speaker (Left)

R

+L

+

–

Insert only the stripped portion.

Black (’ )Red (‘ )

FM aerial

5

To attach the front speaker padsAttach the supplied front speaker pads to thebottom of the speakers to stabilize thespeakers and prevent them from slipping.

Connect the power cord to a walloutlet.Demo mode appears in the display.

Deactivate the demo mode bypressing DISPLAY/DEMO whenthe system power is turned off.The demo mode is also deactivatedwhen you set the time.

R

+L

+

–

Insert only the stripped portion.

Extend the FM leadaerial horizontally.

2

4

3

Gray ( ‘)

NoteDo not place the surround speakers ontop of a TV. This may cause distortionof the colours in the TV screen.

Connect the FM/AM aerials.Set up the AM loop aerial, thenconnect it.

Black ( ’)

FM75

AM

COAXIAL

AM loop aerial

continued

6

Step 2: Setting thetime

You must set the time before using the timerfunctions.

1 Press CLOCK/TIMER SET.The hour indication flashes.

2 Turn the jog dial to set the hour.The clock is on a 24-hour system.

3 Press ENTER/NEXT.The minute indication flashes.

4 Turn the jog dial to set the minute.

Æ‚⁄

„0 )

1 3,52,4

Inserting two size AA (R6)batteries into the remote

TipWith normal use, the batteries should last for aboutsix months. When the remote no longer operatesthe system, replace both batteries with new ones.

NoteIf you do not use the remote for a long period oftime, remove the batteries to avoid possible damagefrom battery leakage.

When carrying this systemDo the following to protect the CDmechanism.1 Press FUNCTION repeatedly until “CD”

appears in the display.

2 Hold down PLAY MODE and pressPOWER so that "LOCK" appears in thedisplay.

} }

]

]

Step 1: Hooking up the system(continued)

7

5 Press ENTER/NEXT.The clock starts working.

Tips• If you’ve made a mistake, start over from step 1.• Setting the time deactivates the demo mode.

If you want to display the demo mode, pressDISPLAY/DEMO when the power is off.

NoteWhen setting the time, set the equalizer display toanything other than Spectrum analyzer pattern 3(see “To change the equalizer display” on page 31).

3,5 6 2 41

Æ‚⁄

„0 )

POWER

continued

nn

Step 3: Presettingradio stations

The 3 band model lets you preset up to 40stations, 20 for FM, 10 for MW and 10 for LW.

The 4 band model lets you preset up to 45stations, 20 for FM, 10 for MW, 10 for LW and5 for UKV.

1 Press TUNER/BAND repeatedlyuntil the band you want appears inthe display.The bands you can receive varydepending on the model you purchased.Be sure to check which bands you canreceive.Every time you press this button, theband changes as follows:3 band model:FM n MW n LW

4 band model:FM n MW n LW n UKV*

* “STEREO PLUS” is displayed whenyou select UKV.

8

Connecting optionalAV components

To enhance your system, you can connectoptional components. Refer to theinstructions of each component.

Connecting audiocomponentsSelect one of the following two connections,depending on the equipment to be connectedand method of connecting.

Connecting an MD deck for digitalrecordingYou can record from CD into the MD deckdigitally by connecting an optical cable.

To the DIGITAL IN jack of the MD deckTUNEDSTEREO

VOLUME

AUTO

Preset number

2 Press TUNING MODE repeatedly toselect “AUTO”.

3 Turn the jog dial.The frequency indication changes andscanning stops when the system tunes ina station. “TUNED” and “STEREO” (fora stereo programme) appear.

TUNEDSTEREO

MHz

VOLUME

AUTO

4 Press TUNER MEMORY.A preset number appears in the display.

5 Turn the jog dial to select the presetnumber you want.

6 Press ENTER/NEXT.The station is stored.

7 Repeat steps 1 to 6 to store otherstations.

To tune in a station with a weaksignalPress TUNING MODE repeatedly to select“MANUAL” in step 2, then turn the jog dialto tune in the station.

To change the preset numberStart over from step 1.

TipThe preset stations are retained for half a day even ifyou unplug the power cord or if a power failureoccurs.

Step 3: Presetting radio stations(continued)

9

Connecting a super wooferspeakerYou can connect an optional super wooferspeaker.

Connecting a VCRMake sure to match the colour of the plugsand the connectors. To listen to the sound ofthe connected VCR, press FUNCTIONrepeatedly until “VIDEO” appears.

NoteIf the sound is distorted when selecting “VIDEO”,switch to “MD” (see previous “Note”).

Connecting an MD deck for analogrecordingMake sure to match the colour of the plugsand the connectors. To listen to the sound ofthe connected MD deck, press FUNCTIONrepeatedly until “MD” appears.

NoteIf you cannot select “MD” even when you havepressed FUNCTION, press POWER while pressingFUNCTION when the power is turned off.“VIDEO” will be switched to “MD”. To return to“VIDEO” do the same procedure.

TipIf you connect a turntable with MM cartridge,connect it to VIDEO/MD IN using the optional MMcartridge equalizer EQ-2 and an audio connectingcord. To listen to the sound, press FUNCTIONrepeatedly until “VIDEO” appears.

To the audio inputof the MD deck

To the audio outputof the MD deck

To super woofer

To the audio output of the VCR

continued

10

Connecting outdooraerialsConnect the outdoor aerial to improve thereception.

FM aerial

Connect the optional FM outdoor aerial. Youcan also use the TV aerial instead.

AM aerial

Connect a 6- to 15- meter (20- to 50- feet)insulated wire to the AM aerial terminal.Leave the supplied AM loop aerial connected.

ImportantIf you connect an outdoor aerial, ground fromy terminal with the screw clamp. To preventa gas explosion, do not connect the earth leadto a gas pipe.

y

FM75

AM

COAXIAL

IEC standard socketconnector(not supplied) Screw clamp

Earth lead (not supplied)

Earth lead (not supplied)

FM75

AM

COAXIAL

y

Insulated wire(not supplied)

Screw clamp

Connecting optional AVcomponents (continued)

Basic O

pera

tion

s

11

Playing a CD— Normal play

1 Press § OPEN/CLOSE and placeup to two CDs on the disc tray.If a disc is not placed properly it will notbe recognized.

To insert a third disc, press DISC SKIPEX-CHANGE to rotate the disc tray.

2 Press one of the DISC 1~3 buttons.The disc tray closes and play starts.If you press · (or · on the remote)when the disc tray is closed, play startsfrom the CD loaded on the tray whosebutton is lit green.

Basic Operations

You can play up to three CDs in a row.

With the labelside up. Whenyou play a singleCD, place it onthe inner circleof the tray.

Æ‚⁄

„0 ) +=2 1

Disc tray number Playing time

Track number

continued

VOLUME

ALL 1DISCS

Æ‚

…

„ » Æ

⁄

⁄ ⁄

bB

v

V

„0 )

…

„» Æ

„DISC SKIPEX-CHANGE

= +

0 )

pP

POWER

CD (

0 ) Æ‚

1/ALL DISCS VOLUME

VOL +/–

12

To Do this

Stop play Press (p on the remote).

Pause Press · (P on the remote).Press again to resume play.

Select a track During play or pause, turn thejog dial clockwise (to goforward) or counterclockwise(to go back) and release itwhen you reach the desiredtrack. Or press + (to goforward) or = (to go back)on the remote.

Find a point in Press and hold down ) ora track 0 ( o r ) / 0 o n t h e

remote) during play andrelease it at the desired point.

Select a CD Press a DISC 1~3 button orin stop mode DISC SKIP EX-CHANGE.

Play only the Press 1/ALL DISCSCD you have repeatedly until “1 DISC”selected appears.

Play all CDs Press 1/ALL DISCS repeatedlyuntil “ALL DISCS” appears.

Remove the CD Press § OPEN/CLOSE.

Exchange other Press DISC SKIPCDs while EX-CHANGE.playing

Adjust the Turn VOLUME (or press VOLvolume +/– on the remote).

Playing a CD (continued) Tips• Pressing · when the power is off

automatically turns the power on and starts CDplayback if there is a CD in the tray (One TouchPlay).

• You can switch from another source to the CDplayer and start playing a CD just by pressing· or the DISC 1~3 buttons (Automatic SourceSelection).

• If there is no CD in the player, “CD NO DISC”appears in the display.

• When a disc tray is selected or the CD placed onthat tray is playing, the DISC 1~3 button for therespective tray lights green.

Basic O

pera

tion

s

13

Recording a CD— CD Synchro Recording

With the sideyou want torecord facingforward

24DISC SKIPEX-CHANGE

The CD SYNCHRO button lets you recordfrom a CD to a tape easily. You can use TYPEI (normal) or TYPE II (CrO2) tapes. Therecording level is adjusted automatically.

1 Press § EJECT and insert a blanktape into deck B.

Æ‚

…

„ » Æ

⁄

⁄ ⁄

„0 )

…

„» Æ

POWER

15REPEAT/DOLBY NR 3

2 Press § OPEN/CLOSE and place aCD.Then press again to close the disc tray.If the indicator for the tray you want torecord is not lit green, press DISC SKIPEX-CHANGE repeatedly so that it lightsgreen.

3 Press CD SYNCHRO.Deck B stands by for recording and theCD player stands by for playback. ·(for front side) lights up.

4 Press EDIT/DIRECTION repeatedlyto select A to record on one side.Select a (or RELAY) to record onboth sides.

5 Press on deck B.Recording starts.

To stop recordingPress on deck B or on the CD player.

Tips• If you want to record from the reverse side, press

ª so that ª (for reverse side) lights up.• When you record on both sides, be sure to start

from the front side. If you start from the reverseside, recording stops at the end of the reverse side.

• When you want to reduce the hiss noise in low-level high-frequency signals, press REPEAT/DOLBY NR so that “DOLBY NR B” appears afterpressing CD SYNCHRO.

NoteYou cannot listen to other sources while recording.

With the labelside up. Whenyou play a singleCD, place it onthe inner circleof the tray.

Æ‚⁄

„0 ) +=

⁄

…

„ »Æ

�

14

Listening to the radio–– Preset Tuning

Preset radio stations in the tuner's memoryfirst (see “Step 3: Presetting radio stations”).

3

21

Æ‚

…

„ » Æ

⁄

⁄ ⁄

„0 )

…

„» Æ

POWER

bB

v

V

TUNER/BAND

VOLUME

STEREO/MONO

= +

VOL +/–

n

Turn counter-clockwise(or press =on the remote)for lower presetnumbers.

TUNEDSTEREO

MHz

VOLUME

PRESET

+–

Preset number Frequency

n

Turn clockwise(or press +on the remote)for higherpreset numbers.

n

1 Press TUNER/BAND repeatedlyuntil the band you want appears inthe display.The bands you can receive varydepending on the the model youpurchased. Be sure to check which bandsyou can receive.Every time you press the button, theband changes as follows:3 band model:FM n MW n LW

4 band model:FM n MW n LW n UKV*

* “STEREO PLUS” is displayed whenyou select UKV.

2 Press TUNING MODE repeatedlyso that “PRESET” appears in thedisplay.MANUAL n AUTO n PRESET

3 Turn the jog dial (or press = or+ on the remote) to tune in thedesired preset station.

To Do this

Turn off the radio Press POWER.

Adjust the volume Turn VOLUME (or pressVOL +/– on the remote).

Basic O

pera

tion

s

15

Recording from theradio

You can record the radio programme on atape by calling up a preset station. You canuse TYPE I (normal) or TYPE II (CrO2) tapes.The recording level is automatically adjusted.

1 Press TUNER/BAND to select theband you want.

2 Press TUNING MODE so that“PRESET” appears in the display.

3 Turn the jog dial to tune in a presetstation.

3

4

Turn clockwisefor higherpreset numbers.

Turn counter-clockwise forlower presetnumbers.

+–

1 2

To listen to non-preset radiostationsPress TUNING MODE repeatedly so that“MANUAL” appears in step 2, then tune inthe station by turning the jog dial.

Tips• Pressing TUNER/BAND when the power is off

automatically turns the power on and tunes to thelast received station (One Touch Play).

• You can switch from another source to the radiojust by pressing TUNER/BAND (AutomaticSource Selection).

• When an FM programme is noisy, pressSTEREO/MONO so that “MONO” appears in thedisplay. There will be no stereo effect, but thereception will improve. Press the button again torestore the stereo effect.

• To improve broadcast reception, reorient thesupplied aerials.

Æ‚

…

„ » Æ

⁄

⁄ ⁄

„0 )

…

„» Æ

POWER

5REPEAT/DOLBY NR 7

TUNEDSTEREO

MHz

VOLUME

PRESET

Preset number Frequency

continued

6

16

Playing a tape

You can use any type of tape, TYPE I(normal), TYPE II (CrO2) or TYPE IV (metal) ,since the deck automatically detects the tapetype. To select either deck A or B, pressDECK A or DECK B on the remote.

113 3º / ‚

4 Press § EJECT and insert a blanktape into deck B.

5 Press r.Deck B stands by for recording.

6 Press EDIT/DIRECTION repeatedlyto select A to record on one side.Select a (or RELAY) to record onboth sides.

7 Press on deck B.Recording starts.

To stop recordingPress on deck B.

Tips• If you want to record from the reverse side, press

ª so that ª (for reverse side) lights up.• When you record on both sides, be sure to start

from the front side. If you start from the reverseside, recording stops at the end of the reverse side.

•To record non-preset stations, select “MANUAL”in step 2, then turn the jog dial to tune in thedesired station.

• When you want to reduce the hiss noise in low-level high-frequency signals, press REPEAT/DOLBY NR so that “DOLBY NR B” appears afterpressing r .

• If noise is heard while recording from the radio,move the respective aerial to reduce the noise.

With the sideyou want torecord facingforward

Recording from the Radio(continued)

2 VOLUME

Æ‚

…

„ » Æ

⁄

⁄ ⁄

„0 )

…

„» Æ

POWER

bB

v

V

0 )

pP

DECK A (

DECK B (

REPEAT/DOLBY NR

VOL +/–

⁄

…

„ »Æ

�

Basic O

pera

tion

s

17

Tips• Pressing · or ª when the power is off

automatically turns the power on and starts tapeplayback if there is a tape in the deck (One TouchPlay).

• You can switch from another source to the tapedeck just by pressing · or ª (Automatic SourceSelection).

• When you want to reduce the hiss noise in low-level high-frequency signals, press REPEAT/DOLBY NR so that “DOLBY NR B” appears.

• When dubbing tapes originally recorded withDolby NR B, the dubbed tape is automaticallyplayed with Dolby NR B.

1 Press § EJECT and insert arecorded tape in deck A or B.

2 Press EDIT/DIRECTION repeatedlyto select A to play one side. Selecta* to play both sides.To play both decks in succession, selectRELAY (relay play).**

3 Press ·. Press ª to play the reverse side. Thetape starts playing.

* The deck stops automatically afterrepeating the sequence five times.** Relay play always follows the followingsequence:Deck A (front side), Deck A (reverse side),Deck B (front side), Deck B (reverse side).

To Do this

Stop play Press (or p on theremote).

Pause (Deck B only) Press . Press again toresume play.

Fast-forward Press ‚ while playingthe front side or º whileplaying the reverse side.

Rewind Press º while playingthe front side or ‚ whileplaying the reverse side.

Remove the cassette Press § EJECT.

Adjust the volume Turn VOLUME (or pressVOL +/– on the remote).

With the sideyou want toplay facingforward

⁄

…

„» Æ

�

18

Recording from atape— High-speed Dubbing

3 Press EDIT/DIRECTION repeatedlyto select A to record on one side.Select a (or RELAY) to record onboth sides.

4 Press .Dubbing starts.

To stop dubbingPress on deck A or B.

Tips• When you dub on both sides, start recording from

the front side. If you record from the reverse side,recording stops at the end of the reverse side.

• If you set EDIT/DIRECTION to a when thetapes you use have different lengths, the tape ineach deck reverses independently. If you selectRELAY, the tapes in both decks reverse together.

• You don’t have to set REPEAT/DOLBY NR, sincethe tape in deck B is automatically recorded in thesame state as the tape in deck A.

You can use TYPE I (normal) or TYPE II(CrO2) tapes. The recording level isautomatically adjusted.

1 Press § EJECT and insert arecorded tape in deck A and a blanktape in deck B.

2 Press HIGH SPEED DUBBING.Deck B stands by for recording.

With the sideyou want toplay/recordfacing forward

1 2 4 1

REPEAT/DOLBY NR

Æ‚

…

„ » Æ

⁄

⁄ ⁄

„0 )

…

„» Æ

POWER 3

⁄

…

„» Æ

�

19

Using the CD display

You can check the remaining time of thecurrent track or that of the CD.

Playing the CD tracksrepeatedly–– Repeat Play

This function lets you repeat a single CD orall CDs in normal play, Shuffle Play andProgramme Play.

The CD Player

DISPLAY/DEMO

/ Press DISPLAY/DEMO duringplayback.Each time you press the button duringnormal playback, the display changes asfollows:

To check the total playing timeand the number of tracks on a CDPress DISPLAY/DEMO in the stop mode.

If you press DISPLAY/DEMO again, theclock display appears for eight seconds thenthe display returns to the previous indication.

n Playing time on the current trackµ

Remaining time on the current trackµ

Remaining time on current CD (1 DISCmode) or“PLAY” display (ALL DISCS mode)

µClock display (for eight seconds)

µEffect (P FILE) name or “EFFECT ON(OFF)”

Æ‚⁄

„0 )

POWER

REPEAT/DOLBY NR

To repeat Press

All the tracks on 1/ALL DISCS repeatedlythe current CD until “1 DISC” appears in

the display.

All the tracks on 1/ALL DISCS repeatedlyall CDs until “ALL DISCS” appears

in the display.

Only one track* REPEAT/DOLBY NRrepeatedly until “REPEAT1” appears in the displaywhile playing the track youwant to repeat.

/ Press REPEAT/DOLBY NR duringplayback until “REPEAT” appearsin the display.Repeat Play starts. Do the followingprocedure to change the repeat mode.

* You can’t repeat a single track during Shuffle Playand Programme Play.

To cancel Repeat PlayPress REPEAT/DOLBY NR so that“REPEAT” or “REPEAT 1” disappears fromthe display.

Æ‚⁄

„0 )

POWER 1/ALL DISCS

20

Playing the CD tracksin random order–– Shuffle Play

You can play all the tracks on one CD or allCDs in random order.

1 Press FUNCTION repeatedly until“CD” appears in the display, thenplace a CD.

2 Press PLAY MODE repeatedly until“SHUFFLE” appears in the display.

3 Press 1/ALL DISCS to choose “1DISC” or “ALL DISCS”.“ALL DISCS” shuffles all the CDs in theplayer. “1 DISC” shuffles the CD whoseDISC indicator is green.

4 Press · .“J” appears and then all the tracks playin random order.

To cancel Shuffle PlayPress PLAY MODE repeatedly until“SHUFFLE” or “PROGRAM” disappearsfrom the display. The tracks continue playingin their original order.

To select a desired CDPress DISC 1~3 .

Tips• You can start Shuffle Play during normal play by

pressing PLAY MODE repeatedly to select“SHUFFLE”.

• To skip a track, turn the jog dial clockwise (orpress + on the remote).Æ‚

…

„ » Æ

⁄

⁄ ⁄

„0 )

…

„» Æ

POWER 4DISC 1-33 2 1

21

Programming the CDtracks–– Programme Play

You can make a programme of up to 32 tracksfrom all the CDs in the order you want themto be played.

3 Press one of the DISC 1~3 buttons toselect a CD.

4 Turn the jog dial until the desiredtrack appears in the display.

5 Press ENTER/NEXT.The track is programmed. Theprogramme step number appears,followed by the total playing time.

6 To programme additional tracks,repeat steps 3 to 5.Skip step 3 to select tracks from thesame disc.

7 Press · .All the tracks play in the order youselected.

To cancel Programme PlayPress PLAY MODE repeatedly until“PROGRAM” or “SHUFFLE” disappearsfrom the display.

15 73

Disc number

Track number

VOLUME

1DISC PROGRAM

VOLUME

1DISC PROGRAM

Total playing time

The last programmed track

Æ‚⁄

„0 )

POWER „

bB

v

V

CD (

CHECKCLEAR

DISC SKIP

42

1 Press FUNCTION repeatedly until“CD” appears in the display, thenplace a CD.

2 Press PLAY MODE repeatedly until“PROGRAM” appears in thedisplay.

continued

22

Playing CDs withoutinterruption–– Non-Stop Play/Applause Mix

You can play CDs without pausing betweentracks or you can mix the sound of applausebetween tracks.

To Press

Check the CHECK on the remoteprogramme repeatedly. After the last

track, “CHECK END”appears.

Clear a track from CLEAR on the remote inthe end stop mode.

Clear a specific CHECK on the remotetrack repeatedly until the

number of the track to beerased lights up, then pressCLEAR.

Add a track to the 1 Select the disc tray with aprogramme DISC 1~3 button.

2 Select the track byturning the jog dial.

3 Press ENTER/NEXT.

Clear the entire once in stop mode orprogramme twice while playing.

Tips• The programme you made remains in the CD

player even after it has been played back. Press· to play the same programme again.

• If “--.--” appears instead of the total playing timeduring programming, this means:– you have programmed a track number

which exceeds 20– the total playing time has exceeded 100 minutes.

Programming the CD tracks(continued)

Æ‚⁄

„0 )

POWER 2 3 1

1 Press FUNCTION repeatedly until“CD” appears in the display, thenplace a CD.

2 Press NON-STOP repeatedly toselect the mode you desire.

3 Press · .

To cancel Non-Stop PlayPress NON-STOP so that “NON-STOP OFF”appears in the display.

To Select

Play without NON-STOP PLAYpausing betweentracks

Mix applause APPLAUSE MIXbetween tracks

23

Recording on a tapemanually

5 Press on deck B.Recording starts.

6 Start playing the source to berecorded.

To Press

Stop recording on the deck B

Pause recording on the deck B

Tips• If you want to record from the reverse side, press

ª so that ª (for reverse side) lights up.• When you want to reduce the hiss noise in low-

level high-frequency signals, press REPEAT/DOLBY NR so that “DOLBY NR B” appears afterpressing r.

• To skip tracks while recording from a tape, press‚ or º on deck A. Deck B stands by forrecording, and you can skip tracks. To resumedubbing, press on deck B.

You can record from CD, tape, or radio asyou like. For example, you can record just thesongs you want or record from the middle ofthe tape. The recording level is adjustedautomatically.

1 Insert a blank tape into deck B.

2 Press FUNCTION repeatedly untilthe source you want to record (e.g.,CD) appears.

3 Press r.Deck B stands by for recording. · (forfront side) lights up.

4 Press EDIT/DIRECTION repeatedlyto select A to record on one side.Select a (or RELAY) to record onboth sides.

The Tape Deck

Æ‚

…

„ » Æ

⁄

⁄ ⁄

„0 )

…

„» Æ

POWER 24 61

REPEAT/DOLBY NR

13 5

24

You can record tracks from all the CDs in theorder you want. When programming, makesure the playing times for each side do notexceed the length of one side of the tape.

Recording a CD byspecifying track order— Programme Edit

1 Place a CD and insert a blank tapeinto deck B.

2 Press FUNCTION repeatedly until“CD” appears in the display.

3 Press PLAY MODE repeatedly until“PROGRAM” appears in thedisplay.

4 Press one of the DISC 1~3 buttons toselect a CD.

5 Turn the jog dial until the desiredtrack appears in the display.

6 Press ENTER/NEXT.The track is programmed. Theprogramme step number appears,followed by the total playing time.

7 To programme additional tracks tobe recorded on side A, repeat steps4 to 6.Skip step 4 to select tracks from the samedisc.

Total playing time(including selected track)Disc number

Track number

VOLUME

1DISC PROGRAM

Previously selected track

Total playing time

1 23 411

110125

REPEAT/DOLBY NR

6

VOLUME

1DISC PROGRAM

8

Æ‚

…

„ » Æ

⁄

⁄ ⁄

„0 )

…

„» Æ

POWER

bB

v

V

CHECK

25

Selecting tape lengthautomatically—Tape Select Edit

You can check the most suitable tape lengthfor recording a CD. Note that you cannot useTape Select Edit for discs containing morethan 20 tracks.

1 Insert a CD.

2 Press FUNCTION repeatedly until“CD” appears in the display.

3 Press EDIT/DIRECTION once, sothat “EDIT” flashes.The required tape length for thecurrently selected CD appears, followedby the total playing time and tracks forside A and side B.

NoteYou cannot use this function after programming.In order to use this function, you must first erase theprogramme (see “To clear the entire programme” onpage 22).

8 Press on the remote to insert apause at the end of side A.“P” appears in the display and the totalplaying time resets to “0.00” in thedisplay.

9 Repeat steps 5 and 6 for tracks fromthe same disc or steps 4 to 6 fortracks from another disc toprogramme the remaining tracks tobe recorded on side B.

10 Press CD SYNCHRO.Deck B stands by for recording and theCD player stands by for playback. ·(for front side) lights up.

11 Press EDIT/DIRECTIONrepeatedly to select A to record onone side. Select a (or RELAY) torecord on both sides.

12 Press on deck B.Recording starts.

To stop recordingPress on the deck B or on the CD player.

To check the orderPress CHECK on the remote repeatedly. Afterthe last track, “CHECK END” appears.

To cancel Programme EditPress PLAY MODE repeatedly until“PROGRAM” or “SHUFFLE” disappearsfrom the display.

TipWhen you want to reduce the hiss noise in low-levelhigh-frequency signals, press REPEAT/DOLBY NRso that “DOLBY NR B” appears after pressing CDSYNCHRO.

26

Æ‚⁄

„0 )

POWER

Looping part of a CD— Loop

With the loop function, you can repeat part ofa CD during playback. This lets you createoriginal recordings.

/ Press and hold LOOP duringplayback at the point you want tostart the Loop function, and releaseto resume normal play.

To adjust the loop lengthTurn the jog dial while holding LOOP (orpress BEAT MENU B or b while holdingLOOP on the remote) to select different looplengths (LOOP 1~20).

Æ‚⁄

„0 )

POWER jog dial

Flashing part of a CD— Flash

With the flash function, you can “flash” theCD sound during playback. This lets youcreate original recordings.

/ Press and hold FLASH duringplayback at the point you want tostart the Flash function, and releaseto resume normal play.

To adjust the flash lengthTurn the jog dial while holding FLASH (orpress BEAT MENU B or b while holdingFLASH on the remote) to select different flashlengths (FLASH 1~20).

To use LOOP and FLASH togetherPress and hold both LOOP and FLASH at thesame time.

Notes• The loop and flash length cannot be adjusted

during this operation. Adjust the loop and flashlengths independently beforehand if necessary.

• To record the flash effect, use the analog (VIDEO/MD OUT) connections or this unit’s tape deck.

jog dial

DJ Effects

FLASHLOOP

27

Æ‚⁄

„0 )

POWER

Waving the equalizer— Wave

With the Wave function, you can fluctuate thegraphic equalizer automatically. This effectcan be used with any source, but it cannot berecorded.

/ Press and hold WAVE to start theWave function, and release toresume normal listening.

To adjust the wave lengthTurn the jog dial while holding WAVE toselect a different wave length (WAVE 1~10).

WAVE

jog dial

jog dial Æ‚⁄

„0 )

POWERPAD A/PAD B

CHAINLEVEL +/–

Using the drum pads

With the drum pads, you can add percussionduring playback. This effect can be used withany source, to create original recordings.

/ Tap drum pad A or B to produce therespective sound.

To change the drum soundPress and hold down pad A or B and turn thejog dial to select the sound you desire. Youcan select from 21 different drum sounds. Thename of the drum sound appears in thedisplay.

KICK˜SNARE˜ . . . ˜SCRATCH PUSH

The sound you select will be stored in pad Aor B.

To create a drum rollTurn the jog dial while holding downCHAIN. You can vary the speed of the drumsby turning the jog dial counterclockwise (forpad A) or clockwise (for pad B).

To adjust the volume of the padsPress LEVEL + or –.

NoteWhen the APPLAUSE MIX function is selected, youwill not hear the drum pad during the applause.

n n

28

Using the beatfunction

With the beat function, you can create avariety of rhythms automatically. This effectcan be used with any source, to createoriginal recordings.

1 Press BEAT ON/OFF to make surethe indicator is off, then startplaying a source.

2 Press BPM CONTROL repeatedly toobtain the beat speed you desire.Every time you press the button a voicesays, “one, two, three, four, one . . .”, thespeeds (BPM 70~140) are also displayed.The beat speed is memorizedautomatically.

3 Press BEAT ON/OFF to start thebeat.Pressing BPM CONTROL lets yousynchronize the beat with the source.

jog dialLEVEL +/–

BEATON/OFF

Æ‚⁄

„0 )

POWER

BEATSPEED

BEATSELECT

BPMCONTROL

To change the speedHold down BEAT SPEED and turn the jogdial (or press BEAT SPEED +/– on theremote) to select the speed you desire (BPM70~140).

To change the beat patternYou can select from 8 different beat patterns.Hold down BEAT SELECT and turn the jogdial (or press BEAT SELECT +/– on theremote) to select the pattern you desire. Thename of the beat pattern appears in thedisplay.

16 BEAT 1˜ 16 BEAT 2 ˜ . . . ˜SAMBA

To cancel the beatPress BEAT ON/OFF. Make sure theindicator is off.

To change the beat volumePress LEVEL + or –.

TipYou can use the drum pads and the beat functiontogether.

NoteWhen the APPLAUSE MIX function is selected, youwill not hear the drum beat during the applause.

nn

29

You can reinforce the bass, create a morepowerful sound, and listen with headphones.

To reinforce bass (DBFB)Press DBFB*.Every time you press the button, the displaychanges as follows:

DBFB n DBFB n display off

“DBFB ” is more effective than

“DBFB ” .

* DBFB = Dynamic Bass Feedback

For a powerful sound (GROOVE)Press GROOVE. The volume switches topower mode, DBFB is automatically set to fullstrength, the equalizer curve changes, and the“GROOVE” button lights up. Press GROOVEagain to return to the previous volume.

Adjusting the soundNotes• With some songs, the music will sound distorted

when you use the DBFB system with the graphicequalizer if the bass is too strong. Adjust the bassslowly while listening to music so that you canmonitor the effect of the adjustment.

• Cancelling GROOVE sets DBFB to “DBFB ”and flattens the equalizer curve. To cancel theDBFB level, press DBFB until the indicationdisappears. Adjust the equalization to obtain theeffect you desire.

To listen through the headphonesConnect the headphones to PHONES jack. Nosound will come from the speakers.

NoteIf you have connected a super woofer, please notethat sound comes from the super woofer even whenthe headphones are connected. Turn off the powerof the super woofer when using headphones.

Æ‚

…

„ » Æ

⁄

⁄ ⁄

„0 )

…

„» Æ

GROOVE

POWER DBFB

PHONES

Sound Adjustmentn

30

Selecting the audioemphasis

The audio emphasis menu lets you select thesound characteristic according to the soundyou are listening to.

The personal file function (see “Making apersonal audio emphasis file”) lets you storeyour own effects.

1 Press MUSIC, MOVIE, or GAME toselect a menu.See the chart “Music menu options”below. The last effect chosen from thatmenu appears in the display.

2 Use the jog dial to select the presetyou desire.The preset name appears in the display.

3 Press ENTER/NEXT.

To cancel the effectPress EFFECT ON/OFF repeatedly so that“EFFECT OFF” appears in the display.

Music menu options“SUR ” appears if you select an effectwith surround effects.

Æ‚⁄

„0 )

POWER EFFECT ON/OFF2

3 1

MENUbutton

MUSIC

MOVIE

GAME

Effect

ROCKPOPJAZZDANCESOUL

ACTIONROMANCESFDRAMASPORTS

SHOOTINGRACINGRPGBATTLEADVENTURE

For

Standardmusic sources

Soundtracksand speciallisteningsituations

Video games

31

Adjusting the audioemphasis

You can adjust the audio emphasis using thegraphic equalizer and surround effect.

Adjusting the graphicequalizerYou can adjust the sound by raising orlowering the levels of specific frequencyranges.

Before operation, first select the audioemphasis you want for your basic sound.

1 Select the audio emphasis you wantfor your basic sound (see “Selectingthe audio emphasis”).

2 Press HIGH FREQUENCY or LOWFREQUENCY repeatedly to select afrequency band.

Æ‚⁄

„0 )

POWER 2 3 5

VOLUME

To change the equalizer displayEach time you press SPECTRUMANALYZER, the equalizer display changes toshow one of the four displays below.

Spectrum analyzer pattern 1

Spectrum analyzer pattern 2

Spectrum analyzer pattern 3

Graphic equalizer curve

VOLUME

VOLUME

VOLUME

VOLUME

µ

µ

µ

m

continued

32

Activating the surroundeffectYou can enjoy the surround effect.

/ Press SURROUND repeatedly sothat “SUR ” appears in thedisplay.

NoteWhen you choose other sound effects, the surroundeffects will be canceled. If you want to memorizethe effect, store it into a personal file (see “Making apersonal audio emphasis file”).

Æ‚

…

„ » Æ

⁄

⁄ ⁄

„0 )

…

„» Æ

POWER SURROUND

3 Turn the jog dial to adjust level.

4 Repeat steps 2 and 3.

5 Press ENTER/NEXT when finished.

NoteIf you choose another menu audio emphasis (otherthan “EFFECT OFF”) the adjusted sound effect islost. To retain the adjusted sound effect for futureuse, store it in a personal file. (See “Making apersonal audio emphasis file”.)

Adjusting the Audio Emphasis(continued)

VOLUME

33

To call up the personal file1 Press P FILE to display the last selected

personal file.2 Use the jog dial to select the personal file

you desire.3 Press ENTER/NEXT.

Making a personalaudio emphasis file—Personal file

You can create a personal file of audiopatterns (surround effect and graphicequalizer) and store them in the memory ofthe unit. Later call up an audio pattern toplay a favourite tape, CD, or radioprogramme. Create up to five audio files.

Before operation, first select the audioemphasis you want for your basic sound.

1 Obtain the sound effect you want byusing the graphic equalizer andsurround effect.

2 Press MEMORY.The personal file number appears in thedisplay.

3 Use the jog dial to select the filenumber (P FILE) where you want tostore the sound effect.

4 Press ENTER/NEXT.The adjusted sound effects are storedunder the selected file number. Thesettings previously stored at thismemory location are erased andreplaced by the new settings.

4

Æ‚⁄

„0 )

POWER 3

VOLUME

2

34

NORMAL modeThe surround speakers provide reverberationand reflective sound effects that emphasizethe sound from the front speakers.

WHISPER modeThe sound from the front speakers is cut offand output from the surround speaker withits sound decreased. For instance, when youwant to listen to the sound in bed, it issuitable to set the surround speakers oneither side of the bed.

FRONTSPEAKER (R)

SURROUNDSPEAKER (R)

SURROUNDSPEAKER (R)

SURROUNDSPEAKER (L)

FRONTSPEAKER (L)

FRONTSPEAKER (L)

FRONTSPEAKER (R)

SURROUNDSPEAKER (L)

SONIC FORMATION

Æ‚

…

„ » Æ

⁄

⁄ ⁄

„0 )

…

„» Æ

POWER

n

N

Switching theSpeaker Formation–Sonic formation

You can select from four speaker formationsdepending on your listening situation.

/ Press SONIC FORMATIONrepeatedly until the mode you wantappears in the display.As you press SONIC FORMATION, themode changes as follows:NORMAL n WHISPER n LINK

FRONT ONLY

35

SURROUNDSPEAKER(R)

SURROUNDSPEAKER

(L)

FRONTSPEAKER(R)

FRONTSPEAKER

(L)

LINK modeThe same sound is output from the frontspeakers and surround speakers. Forinstance, when you want to listen to the samesound in two rooms, it is suitable to set thefront speakers and the surround speakers ineach room.

FRONT ONLY modeNo sound is output from the surroundspeakers. Sound comes from the frontspeakers only.

NoteDo not place the surround speakers on top of a TV.This may cause distortion of the colours in the TVscreen.

FRONTSPEAKER

(L)

FRONTSPEAKER(R)

SURROUNDSPEAKER

(L)

SURROUNDSPEAKER(R)

36

Other Features

What is the Radio Data System?Radio Data System (RDS) is a broadcastingservice that allows radio stations to sendadditional information along with the regularprogramme signal. This tuner offersconvenient RDS features like station namedisplay and location of stations byprogramme type. RDS is available only onFM stations.*

NoteRDS may not work properly if the station you aretuned to is not transmitting the RDS signal properlyor if the signal strength is weak.* Not all FM stations provide RDS service, nor do

they provide the same type of services. If you arenot familiar with the RDS system, check with yourlocal radio stations for details on RDS services inyour area.

Receiving RDS broadcasts

/ Simply select a station from the FMband.When you tune in a station thatprovides RDS services, the stationname appears in the display.

Using the Radio DataSystem (RDS)(For Western European modelonly)

To check the RDS informationEach time you press DISPLAY/DEMO, thedisplay changes as follows:

n Station name*µ

Frequencyµ

Programme type*µ

Clock displayµ

Effect (P FILE) name or“EFFECT ON (OFF)”

* If the RDS broadcast is not received, the stationname and programme type may not appear in thedisplay

Locating a station byprogramme type (PTY)You can locate a station you want by selectinga programme type. The unit tunes in the typeof programmes currently being broadcastfrom the RDS stations stored in the tuner’spreset memory.

1 Press PTY

2 Turn jog dial to select theprogramme type you want. See the“List of programme types” sectionbelow.

3 Press ENTER/NEXT.The unit starts searching the preset RDSstations (“SEARCH” and the selectedprogramme type are shown alternatelyin the display).When the tuner receives a programme,the preset station number flashes.

4 Turn jog dial to display the presetstation number you desire.

37

5 Press ENTER/NEXT while thepreset station number is flashing.

To cancel PTY searchPress PTY again.

List of programme types (PTY)

AFFAIRSTopical programmes that expand oncurrent news.

ALARMEmergency broadcasts.

CULTUREProgrammes about national or regionalculture.

DRAMARadio plays and serials

EDUCATIONEducational programmes, such as “how-to” programmes and advice.

INFORMATIONProgrammes about consumer affairs,medical advice, and weather.

LIGHT MUSICClassical music, such as instrumentals,and vocal and choral works.

M.O.R. MUSICEasy listening (middle of the roadmusic).

NEWSNews programmes

OTHER MUSICMusic, such as jazz, rhythm and blues,and reggae.

POP MUSICpopular music programmes

ROCK MUSICRock music programmes

SCIENCEProgrammes about the natural sciences

CLASSICSPerformances of major orchestras,chamber music, opera, etc.

SPORTSports programmes

VARIEDProgrammes containing celebrityinterviews, panel games, and comedy.

NONEAny programming not defined above

Note”NO PTY” appears when the programme type thatyou selected is not currently being broadcast.

38

Singing along:Karaoke

n5 Adjust the microphone volume by

turning MIC LEVEL.

When you are doneTurn MIC LEVEL to 0 and disconnect themicrophone from MIX MIC, then pressKARAOKE PON/MPX repeatedly so that“h” disappears.

Mixing and recordingsounds

1 Do the above steps 1 to 5. Then,insert a tape in deck B.

2 Press FUNCTION repeatedly toselect the source you desire and setit to pause mode.

3

Æ‚⁄

„0 )

POWER

VOLUME2 1,5

You can sing along with any stereo CD ortape by turning down the singer’s voice. Youneed to connect an optional microphone.

1 Turn MIC LEVEL to 0 to turn downthe microphone control level.

2 Connect an optional microphone toMIX MIC.

3 Press KARAOKE PON/MPXrepeatedly to obtain the karaokeeffect you desire.Every time you press the button, thedisplay changes as follows:

KARAOKE PON n MPX R n MPX L

EFFECT OFF (ON) NThe h indicator appears in the displaywhen a karaoke mode is activated.To sing karaoke with decreasing thevocal level of a CD, select KARAOKEPON. To sing karaoke of multiplex CDor tape, select MPX R or MPX L.

4 Start playing the music and adjustthe volume.

2

5 4 1

5

3

Æ‚

…

„ » Æ

⁄

⁄ ⁄

„0 )

…

„» Æ

POWER

39

Falling asleep tomusic— Sleep Timer

You can let the system turn off at the presettime, so you can sleep to the music. You canpreset the time to be turned off by 10minutes.

/ Press SLEEP.Every time you press the button, theminute display (the turn-off time)changes as follows:AUTO n 90min n 80min n 70minn … n 10min n OFF n AUTO …

When you choose autoThe power turns off when the current CD ortape finishes playback (for up to 100minutes).

To check the remaining timePress SLEEP once.

To change the time to turn offSelect the time you want by pressing SLEEP.

To cancel the Sleep Timer functionPress SLEEP repeatedly until “OFF” appears.

Æ‚⁄

„0 )

POWER SLEEP

3 Press r.

4 Press .

5 Press · to start playing the CDplayer (or tape deck A).Playback starts. Start singing along withthe music.

To stop recordingPress p on deck B and the CD player.

Tips• If acoustic feedback (howling) occurs, move the

microphone away from the speakers or change thedirection of the microphone.

• If you want to record your voice through themicrophone only, you can do so by selecting theCD function and not playing a CD.

Notes• If you press EFFECT ON/OFF or recall a sound

effect, the karaoke mode is cancelled.• The instrumental sound may be reduced as well as

the singer’s voice when the sound is recorded inmonaural.

• The singer’s voice may not be reduced when:—only a few instruments are playing—a duet is being played—the source has strong echoes or chorus—the singer’s voice deviates from the centre.—the voice on the source is singing in high

soprano or tenor.

40

1 Prepare the music source you wantto play.• CD: Insert a CD. To start from a

specific track, make a programme (see“Programming the CD tracks”).

• Tape: Insert an tape with the side youwant to play facing forward.

• Radio: Tune in the preset station youwant (see “Step 3: Presetting radiostations”).

2 Adjust the volume.

3 Press CLOCK/TIMER SET.“SET (DAILY 1)” appears.

4 Turn jog dial to select DAILY 1 or 2,then press ENTER/NEXT.“ON” appears and the hour digits flashin the display.

VOLUME

1

Waking up to music— Wake-up Timer

5 Set the time to start playback.Turn jog dial to set the hour, then pressENTER/NEXT.The minute indication starts flashing.

Turn jog dial to set the minute, thenpress ENTER/NEXT.The hour indication flashes again.

6 Set the time to stop playbackfollowing the above procedure.

7 Turn jog dial until the music sourceyou want appears.The indications change as follows:TUNER n CD PLAY n TAPE PLAY

8 Press ENTER/NEXT.The start time, followed by the stop timeand the music source, appears, then theoriginal display appears.

9 Turn off the power.

You can wake up to music at a preset timeevery day. Make sure you have set the clock(see “Step 2: Setting the time”).

3

TIMER SELECT 2

4,5,6,7,8

Æ‚

…

„ » Æ

⁄

⁄ ⁄

„0 )

…

„» Æ

9

VOLUME

1

41

To timer-record, you must preset the radiostation (see “Step 3: Presetting radiostations”) and set the clock (see “Step 2:Setting the time”) beforehand.

6

3,4,52

TIMER SELECT

1 Tune in the preset radio station (see“Listening to the radio”).

2 Press CLOCK/TIMER SET.“SET (DAILY 1)” appears.

Æ‚

…

„ » Æ

⁄

⁄ ⁄

„0 )

…

„» Æ

7

To check the settingPress TIMER SELECT and turn the jog dial toselect the respective mode (DAILY 1 orDAILY 2), then press ENTER/NEXT. Tochange the setting, start over from step 1.

To cancel the timer operationPress TIMER SELECT and turn the jog dial toselect “OFF”, then press ENTER/NEXT.

TipThe power turns on 15 minutes before the presettime.

NoteWhen setting the wake-up timer, set the equalizerdisplay to anything other than Spectrum analyzerpattern 3 (See “To change the equalizer display” onpage 31).

Timer-recording radioprogrammes

continued

42

To check the settingPress TIMER SELECT and turn the jog dial toselect “REC”, then press ENTER/NEXT. Tochange the setting, start over from step 1.

To cancel the timer operationPress TIMER SELECT and turn the jog dial toselect “OFF”, then press ENTER/NEXT.

Notes• When setting the timer-recording, set the equalizer

display to anything other than Spectrum analyzerpattern 3 (See “To change the equalizer display”on page 31).

• If the power is on at the preset time, the recordingwill not be made.

3 Turn jog dial to select REC, thenpress ENTER/NEXT.“ON” appears and the hour digits flashin the display.

4 Set the time to start recording.Turn jog dial to set the hour, then pressENTER/NEXT.The minute indication starts flashing.

Turn jog dial to set the minute, thenpress ENTER/NEXT.The hour indication flashes again.

5 Set the time to stop recordingfollowing the above procedure.The start time appears, followed by thestop time, the recording source and theradio station, then the original displayappears.

6 Insert a recordable tape.

7 Turn off the power.When the recording starts, the volumelevel is set to the minimum.

Timer-recording radio programmes(continued)

VOLUME

REC

VOLUME

REC

43

PrecautionsCleaning the cabinetUse a soft cloth slightly moistened with milddetergent solution.

To save a tape permanentlyTo prevent a tape from being accidentally recordedover, break off the cassette tab from side A or B asillustrated. If you later want to reuse the tape forrecording, cover the broken tab with adhesive tape.

When you are using a TYPE II (CrO2) or TYPE IV(metal) cassette, be careful not to cover the detectorslots which allow the tape player to automaticallydetect the type of tape.

On operating voltageBefore operating the system, check that theoperating voltage of your system is identical withthe voltage of your local power supply.

On safety• The unit is not disconnected from the AC power

source (mains) as long as it is connected to thewall outlet, even if the unit itself has been turnedoff.

• Unplug the system from the wall outlet (mains) ifit is not to be used for an extended period of time.To disconnect the cord (mains lead), pull it out bythe plug. Never pull the cord itself.

• Should any solid object or liquid fall into thecomponent, unplug the stereo system and havethe component checked by qualified personnelbefore operating it any further.

• The mains lead must be changed only at thequalified service shop.

On placement• Place the stereo system in a location with adequate

ventilation to prevent heat build-up in the stereosystem.

• Do not place the unit in an inclined position.• Do not place the unit in locations where it is;

— Extremely hot or cold— Dusty or dirty— Very humid— Vibrating— Subject to direct sunlight

On operation• If the stereo system is brought directly from a cold

to a warm location , or is placed in a very damproom, moisture may condense on the lens insidethe CD player. Should this occur, the system willnot operate properly. Remove the CD and leavethe system turned on for about an hour until themoisture evaporates.

• When you move the system, take out any discs.

If you have any questions or problems concerningyour stereo system, please consult your nearestSony dealer.

Notes on CDs• Before playing, clean the CD with a cleaning cloth.

Wipe the CD from the centre out.• Do not use solvents such as benzene, thinner,

commercially available cleaners or anti-staticspray intended for vinyl LPs.

•Do not expose the CD to direct sunlight or heatsources such as hot air ducts, nor leave it in a carparked in direct sunlight.

Additional Information

Detector slots

continued

44

Troubleshooting

If you run into any problem using this stereosystem, use the following check list.First, check that the power cord is connectedfirmly and the speakers are connectedcorrectly and firmly.

Should any problem persist, consult yournearest Sony dealer.

General

The display starts flashing as soon as youplug in the power cord even though youhaven’t turned on the power(demonstration mode).

•Press DISPLAY/DEMO when the poweris turned off.The demonstration mode appearsautomatically the first time you plug inthe power cord. If there is a power outagelasting longer than half a day, redo thefollowing:— Clock setting (see “Step 2: Setting the

time”)— Preset stations (see “Step 3: Presetting

radio stations”)— Timer settings (see “Waking up to

music” and “Timer recording radioprogrammes”).

There is no sound.•Rotate VOLUME clockwise.•The headphones are connected.•Insert only the stripped portion of the

speaker cord into the SPEAKER jack.Inserting the vinyl portion of the speakercord will obstruct the speakerconnections.

Before placing a cassette in thetape deckTake up any slack in the tape. Otherwise the tapemay get entangled in the parts of the tape deck andbecome damaged.

When using a tape longer than 90minutesThe tape is very elastic. Do not change the tapeoperations such as play, stop, and fast-winding etc.frequently. The tape may get entangled in the tapedeck.

Cleaning the tape headsClean the tape heads after every 10 hours of use.When the tape heads become dirty

— the sound is distorted— there is a decrease in sound level— the sound drops out— the tape does not erase completely— the tape does not record

Make sure to clean the tape heads before you startan important recording or after playing an old tape.Use separately sold dry-type or wet-type cleaningcassette. For details, refer to the instructions of thecleaning cassette.

Demagnetizing the tape headsDemagnetize the tape heads and the metal parts thathave contact with the tape every 20 to 30 hours ofuse with a separately sold demagnetizing cassette.For details, refer to the instructions of thedemagnetizing cassette.

Precautions (continued)

45

There is severe hum or noise.• A TV or VCR is placed too close to the

stereo system. Move the stereo systemaway from the TV or VCR.

The sound from the connected source isdistorted.

• If “VIDEO” appears in the display whenyou press FUNCTION, switch the displayto “MD” (see “Notes: Connecting aVCR”).

“0:00” flashes in the display.• A power interruption occurred. Set the

clock and timer settings again.

The timer does not function.• Set the clock correctly.

DAILY1, DAILY 2, and REC do not appearwhen you press the TIMER SELECT button.

• Set the timer correctly.• Set the clock.

The remote does not function.• There is an obstacle between the remote

and the system.• The remote is not pointing in the

direction of the system’s sensor.• The batteries have run down. Replace the

batteries.

There is acoustic feedback.• Decrease the volume level.• Move the microphone away form the

speakers or change the direction of themicrophone.

The colour irregularity on a TV screenpersists.

• Turn off the TV set once, then turn it onafter 15 to 30 minutes. If the colourirregularity still persists, place thespearkers farther away from the TV set.

Speakers

Sound comes from one channel orunbalanced left and right volume.

•Check the speaker connection andspeaker placement.

There is no sound from the surroundspeakers.

•Press SONIC FORMATION to select amode other than “FRONT ONLY”.

There is no sound from the front speakers.•Press SONIC FORMATION to select a

mode other than “WHISPER”.

CD Player

The CD tray does not close.•The CD is not placed properly.

The CD will not play.•The CD is not lying flat in the disc tray.•The CD is dirty.•The CD is inserted label side down.•Moisture condensation has built up.

Remove the CD and leave the systemturned on for about an hour until themoisture evaporates.

Play does not start from the first track.•The player is in programme or shuffle

mode. Press PLAY MODE repeatedlyuntil “PROGRAM” or “SHUFFLE”disappear.

“OVER” is displayed.•You have reached the end of the CD.

Press and hold 0 to return.

continued

46

Tape Deck

The tape does not record.•No tape in the cassette holder.•The tab has been removed from the

cassette (see “To save a tapepermanently” on page 43).

•The tape has reeled to the end.

The tape does not record nor play or thereis a decrease in sound level.

•The heads are dirty. Clean them (see“Cleaning the tape heads” on page 44).

•The record/playback heads aremagnetized. Demagnetize them (see“Demagnetizing the tape heads” on page44).

The tape does not erase completely.•The record/playback heads are

magnetized. Demagnetize them (see“Demagnetizing the tape heads” on page44).

There is excessive wow or flutter, or thesound drops out.

•The capstans or pinch rollers are dirty.Clean them (see “Cleaning the tapeheads” on page 44).

Noise increases or the high frequencies areerased.

•The record/playback heads aremagnetized. Demagnetize them (see“Demagnetizing the tape heads” on page44).

Troubleshooting (continued) Tuner

Severe hum or noise (“TUNED” or“STEREO” flashes in the display.

•Adjust the aerial.•The signal strength is too weak. Connect

the external aerial.

A stereo FM programme cannot bereceived in stereo.

•Press STEREO/MONO so that “STEREO”appears.

If other troubles not describedabove occur, reset the system asfollows:1 Unplug the power cord.2 Plug the power cord back in.3 Press SPECTRUM ANALYZER, ENTER/

NEXT, and DISC 1 at the same time.4 Press POWER to turn on the power.

47

Tape player sectionRecording system 4-track 2-channel stereoFrequency response 60 – 13,000 Hz (±3 dB),(DOLBY NR OFF) using Sony TYPE I

cassette60 – 14,000 Hz (±3 dB),using Sony TYPE IIcassette

Wow and flutter ±0.15% W.Peak (IEC)0.1% W.RMS (NAB)±0.2% W.Peak (DIN)

Tuner sectionFM stereo, FM/AM superheterodyne tuner

FM tuner section

Tuning range3 band model: 87.5 – 108.0 MHz

(50 kHz step)4 band model: 65.0 – 74.0 MHz

(10 kHz step)87.5 – 108.0 MHz(50 kHz step)

Aerial FM lead aerialAerial terminals 75 ohm unbalancedIntermediate frequency 10.7 MHz

UKV tuner section (4 band model only)Tuning range 65.0 – 74.0 MHz

(10kHz step)Polar stereo

AM tuner section

Tuning range MW: 531 – 1,602 kHz(with interval set at9 kHz)LW: 153 – 279 kHz(with interval set at3 kHz)

Aerial AM loop aerialAerial terminals External aerial terminalIntermediate frequency 450 kHz

Amplifier sectionDIN power output 80 + 80 watts

(8 ohms, at 1kHz, DIN)Continuous RMS power output:

100 + 100 watts(8 ohms at 1 kHz,10% THD)

Music power output: 160 + 160 watts(8 ohms at 1 kHz, 10%THD)

Inputs VIDEO/MD IN (phonojacks): voltage 250 mV,impedance 47 kilohmsMIX MIC (phone jack):sensitivity 1 mV,impedance 10 kilohms

Outputs VIDEO/MD OUT (phonojacks): voltage 250 mVimpedance 1 kilohmsPHONES (stereo phonejack):accepts headphones of 8ohms or more.SPEAKER:accepts impedance of 8 to16 ohmsSURROUND SPEAKER:accepts impedance of 16ohms.SUPER WOOFER:Voltage 1 V, impedance 1kilo ohm

CD player sectionSystem Compact disc and digital

audio systemLaser Semiconductor laser

(λ=780nm)Emission duration:continuous

Laser output Max. 44.6 µW**This output is the valuemeasured at a distance of200 mm from theobjective lens surface onthe Optical Pick-up Blockwith 7 mm aperture.

Frequency response 2 Hz – 20 kHz (±0.5 dB)Wavelength 780 – 790 nmSignal-to-noise ratio More than 90 dBDynamic range More than 90 dBCD OPTICAL DIGITAL OUT(Square optical connector jack, rear panel)Wavelength 600 nmOutput Level –18 dBm

Specifications

continued

48

SpeakerFront Speaker (SS-L90V)Speaker system 4-way, 5-unit,

bass-reflex typeSpeaker unitsWoofer: 17 cm, cone typeCentre Tweeter: 5 cm, cone typeSide Tweeter: 5 cm, cone type x2Super Tweeter: 2 cm, dome typeNominal impedance 8 ohmsDimensions (w/h/d) Approx. 220 x 330 x 315

mmMass Approx. 5 kg net per

speakerSurround Speaker (SS-SR101)Speaker system 1-way, 1-unit,

bass-reflex typeSpeaker unitsFull-range: 8 cm, cone typeNominal impedance 16 ohmsDimensions (w/h/d) Approx. 205 x 95 x 240

mmMass Approx. 1.1 kg net per

speaker

GeneralPower requirements 220 - 230 V AC , 50/60 HzPower consumption 230 wattsDimensions (w/h/d) Approx. 280 x 330 x 366

mmMass Approx. 9.5 kgSupplied accessories:

AM loop aerial (1)Remote RM-SD80 (1)Sony SUM-3 (NS)batteries (2)FM lead aerial (1)Speaker cords (4)Front speaker pads (8)

Design and specifications are subject to changewithout notice.

Specifications (continued)

49

IndexL, M

Loop 26

N

Normal Play 11

O

One Touch Play 12, 15, 17

P , Q

Personal file 33Playing

a CD 11a preset radio station 14tracks in random order(Shuffle Play) 20tracks in the desiredorder (Programme Play)21tracks repeatedly(Repeat Play) 19

Presetting radio stations 7Preset tuning 14Programme Play 21Protecting recordings 43PTY 36

R

Radio Data System 36Radio stations

presetting 7tuning in 14

Recordinga CD 13a radio programme 15timer recording 41

Repeat Play 19Resetting the system 46

S

Saving recordings 43Selecting the audio emphasis

30Setting the time 6Shuffle Play 20Sleep Timer 39Sound adjustment 29Speakers 4, 9Sonic formation 34Station name 36

T, U, V

Timerfalling asleep to music39timer recording 41waking up to music 40

Troubleshooting 44Tuner 7, 14Tuning interval 8, 47

W, X, Y, Z

Wake-up timer 40Wave 27

A

Adjustingthe audio emphasis 31the sound 29the volume 12, 14, 17

Aerials 4, 10Automatic Source Selection

12, 15, 17

B

Batteries 6

C

CD player 11, 19CD Synchro Recording 13Clock setting 6Connecting. See Hooking up

D

Display 5, 19, 31

E

Edit 24

F, G

Flash 26

H, I, J

Hooking upoptional components 8the aerials 5, 10the power 5the system 4

K

Karaoke 38

Sony Corporation Printed in Indonesia