Upload
amit-sagdeo
View
288
Download
7
Embed Size (px)
Citation preview
WELCOME TO THERMAX PROFETHERM
– Manufacture and Market Vapour Absorption Chillers• Unlike electrical chillers, vapour absorption chillers are powered by heat sources like steam, hot water, waste heat, natural gas and other readily available low cost fuels.
– Established in 1984 in partnership with Sanyo• 1988 – Technical Collaboration• 1994 – Independent
– Presence• 2 State-of-the-art manufacturing facilities in Pune (India) and Zhejiang (China)• More than 6000 installations across 70 countries• Major markets include USA, Europe, India, Middle East, South East Asia• Extensive Global Service Network
About Us
Thermally Activated Technology• Fuel Driven Chillers: 50 – 1600 TR
• Steam Driven Chillers: 50 – 3500 TR
• Hot Water Driven Chillers:Low Temp: 10 – 1350 TRMedium Temp: 50 – 2000 TRHigh Temp: 50 – 3500 TR
• Multi Energy Chillers:50 – 3500 TR without fuel firing50 – 1350 TR with fuel firing option
• Hybrid Chillers: 25 – 500 TR (up to -40°C)
• Heat Pumps: 500 kW – 40 MW
• Chiller Heaters:100-3500 TR Cooling250 kW to 9 MW Heating
Breaking The Ground
With
Unique Solutions
for
Milk Processing
1 Degree Water Chiller
High Efficiency Chiller Heater
1°C GLYCOL FREE ABSORPTION MILK CHILLER
• To overcome all the detrimental effects of PG use, Thermax has introduced a series of chillers which can give 1oC chilled water outlet temperature.
• Sufficient care has been taken in the design to avoid freezing of water.
• As pure water is being used, optimum HTCs are observed in the chiller and cost/ TR reduces.
• Also, , the recurring costs of glycol maintenance is avoided
• The pumping power requirement will also reduce
1oC Chiller : Glycol Free Operation
• To overcome all the energy losses of conventional IBT system, Thermax has introduced a series of chillers which can give 1oC chilled water outlet temperature.
• Since open Ice bank system were used there are lot of losses energy and the compressor were running continuously consuming lot of electrical energy.
• With 1oC water Chiller we can reduce these losses as the water can go directly to the PHE for milk chilling or through closed Hot/cold well circuit.
1oC Chiller : Reduce energy losses of IBT System
• At Lower Chilled water outlet temperatures, LiBr is added to the refrigerant circuit to avoid freezing
• The amount of LiBr to be added to the refrigerant circuit is governed by depression in freezing point desired.
• LiBr amount added is continuously monitored and maintained during chiller operation to ensure efficient running
• SS tubes are used in the Evaporator
• Chilled water flow meter is included as a standard feature
• The flow meter is used to monitor & control flow velocity in the tubes, the flow is not allowed to go below 60% of rated flow there by maintaining minimum velocity of water in tubes
1oC Chiller : An Overview of Technology
Successful Installations
Heritage foods Ltd., 130 TR, Chilled water profile : 5 –> 1oC
Umang dairies Ltd. ,400 TR, Chilled water profile : 5 –> 1oC
A PLANT IN AP(350,000 LPD Capacity)
(MILK, POWDER, PANEER, CURD, BUTTER, LASSI, BUTTER MILK & ALLIED DAIRY PRODUCTS)
Utility Details• Boiler : 3 TPH @10.54 Barg
4 TPH @ 17.5 Barg
• Fuel : Briquette, Wood, Coal
• Refrigeration System :– IBT System : For Chilled Water Generation
» KC6 x 3 Nos. (150HP x 3 Nos.)
– Cold Storage : Maintain Room temp at 0~5 Deg C» KC2 x 3 Nos. (40 HP x 3 Nos.)
– Deep Freezer : Maintain Room temp at -20 Deg C» KC21 + HDI Frick
– IBT System : For Chilled Water Generation» Steam driven Vapor Absorption Heat Pump- Chiller Heater
OPERATIONAL DETAILS
• KC6 x 1 No. – 18 Hours• KC6 x 1 No. – 10 Hours• KC2 x 3 Nos. – 72
Hours
• KC6 x 1 No. – 16-18 Hours
• 133 TR VAM – 22 Hours
BEFORE AFTER
Chilled water In100CMH @ 5~7 Deg C
IBT TANK
PHE
Ammonia Vapor
Am
mon
ia L
iqui
d
S W
Chilled water Out to Plant
100 CMH @ 1.0 ~2.0 Deg CW
Chilled water Out100CMH @ 3.5 Deg C
Chilled water Out100CMH @ 1~2 Deg C
W
W
S
Chilled water In100CMH @ 5~7 Deg C
PHE
Ammonia Vapor
Am
mon
ia L
iqui
d
S W
Chilled water In100 CMH @ 1.0 Deg C
OPTIONAL :HOT WATER : 3,00,000 kcal/hrHot Water Inlet30CMH @80/90 Deg C
Ammonia LiquidFor the Cold Room
IBT TANK
Chilled water Out100CMH @ 1 Deg C
OLD SYSTEM
NEW SYSTEM
REMOTE PERFORMANCE DATA
HIGH EFFICIENCY CHILLER - HEATER
BYTHERMAX
• HEAT SOURCE • Dry Saturated Steam (3.0 – 10.0 bar.g)
• High temperature hot water (145 – 180 oC)
• Direct Fuel Firing (Gas/Oil/LPG/Propane)
• Exhaust Gas (275 – 600 oC)
• CAPACITY RANGE • Cooling : 100 – 3500 TR
• Heating : 100 kW – 9 MW
High Efficiency Chiller Heater
• TEMPERATURE RANGE• Cooling : -2 – 30 oC Delta T : 30 oC max• Heating : 30 – 90 oC Delta T : 5 – 50 oC
• 23% saving in overall heat input OR
40% saving on heat input for heating
High Efficiency Chiller Heater
19© Copyright Protected
391 kg/hr steam @8 bar(g)
380 kg/hr steam @ 8 bar(g)
260 kW heating 260 kW
heating
352 kW(100 TR ) cooling
600 kg/hr steam@ 8 bar
Cool
ing
and
Heati
ng
Steam Driven Chiller heater(Liv Cocalor)
23%less steam
391 380 + = 771 600
Hot water generator
Steam Driven Chiller(Liv Fervo)
Conventional System New SystemVS
352 kW(100 TR ) cooling
A Comparison
20© Copyright Protected
Heat rejection in Cooling Tower in steam fired chiller
Heat rejection in Cooling Tower in steam fired chiller heater
352 kW Refrigeration
253 kW heat Input
605 kW cooling tower heat rejection
352 kW Refrigeration
260 kW heating capacity
399 kWheat input
491 kW cooling tower heat rejection
Heat rejection reduced by
20% thus reduction in evaporative
losses
Reduce Cooling Tower Evap. Losses
High Efficiency Chiller Heater - Features• Chiller and heater circuit are conjoined in a way that both are made mutually
interdependent.
• Easy controllability of vapor flow during various load conditions.
• Reduced Energy consumptions like Gas / oil /Steam etc, 40 % reduction in Heating energy
• Reduction in CO2 emission.
• Heat rejection to cooling water is reduced results in reduction in make-up water required for cooling tower
• As Chiller heaters use latent heat of refrigerant vapour, 75% of chilling capacity can be attained as heating duty, as against electric chillers which use sensible heat due to which only ~8-10% of chilling duty can be provided as heating duty.
High Efficiency Chiller Heater - Applications• Dairy• Cooling – Milk chilling• Heating – Pasteurization
• Breweries• Cooling – Wort cooling• Heating - Sparging
• Coffee processing• Cooling – Air conditioning, Agglomerator• Heating - Dehumidification
• Tea processing• Edible oil• Malt processing• Minerals & metals
HIGH EFFICIENCY CHILLER - HEATER
CASE STUDY
Capacity Chilled water Cooling water Heat source Hot water
TR Temp profile I/L Temp Flow8 kg
steam
Flow Temp profile Flow
°C °C m3/hr Kg/hr °C m3/hr400 5-1 32 400 2884 80 - 85 184.7
Dairy- Uttar Pradesh
• Breweries require to cool and reheat their process fluids as per the requirement of the manufacturing process.
• A Chiller heater has been supplied to a brewery for the same with a scheme as follows:
Capacity Chilled water Cooling water Heat source Hot water
TR Temp profile I/L Temp Flow8 kg
steam
Flow Temp profile Flow
°C °C m3/hr Kg/hr °C m3/hr160.5 12-4 30 180 1030 75-90 25
CHILLER HEATER
Brewery- Aurangabad
• A similar scheme has been provided to a Coffee making plant in Hosur.
Capacity Chilled water Cooling water Heat source Hot water
TR Temp profile I/L Temp Flow8 kg
steam
Flow Temp profile Flow
°C °C m3/hr Kg/hr °C m3/hr197 17-4 29.4 220 911 60-90 6
CHILLER HEATER
Coffee Making Plant- Hosur
THANK YOU !