Embed Size (px)
Citation preview
NOA No. 20-0427.08 Expiration Date: June 09, 2025
Approval Date: May 21, 2020 Page 1
MIAMI-DADE COUNTY PRODUCT CONTROL SECTION
11805 SW 26 Street, Room 208 DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) Miami, Florida 33175-2474 BOARD AND CODE ADMINISTRATION DIVISION T (786) 315-2590 F (786) 315-2599
NOTICE OF ACCEPTANCE (NOA) www.miamidade.gov/economy
International Impact Building Products, LLC 5900 Australian avenue, suite # 300 West palm Beach, FL 33407 SCOPE:This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami-Dade County RER -Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami-Dade County Product Control Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami-Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code.
This product is approved as described herein and has been designed to comply with the Florida Building Code, including the High Velocity Hurricane Zone. DESCRIPTION: “Titan 50” Series Aluminum Sliding Glass Door (Reinforced) w/ 90 & 135 degree corners & pockets-LMI APPROVAL DOCUMENT: Drawing No. W15-06 Rev B, titled “Series Titan-50 Alum SLD. Glass Door (L.M.I.)”, sheets 1 through 10 of 10, prepared by AL-Farooq Corporation, dated 02/25/15 and last revised on MAR 27, 2018, signed and sealed by Javad Ahmad, P.E., bearing the Miami-Dade County Product Control Revision stamp with the Notice of Acceptance number and expiration date by the Miami-Dade County Product Control Division.
MISSILE IMPACT RATING: Large Missile Impact Resistant Limitations: 1. See Design Pressure Vs door sizes in sheet 1. See sheet 7 for reinforcement requirement for Deep or Shallow
interlocks. See sheet 8 for 900, 1350 details and pocket installations.2. See pair anchors at intermediate members and cluster pair of anchors required at interlock, astragal and corners
in sheet 1. See alternate anchors at pocket jambs in sheet 1 and pocket adapter installation detail in sheet 8.3. Pocket under separate approval and to be reviewed by AHJ.
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and series andfollowing statement: "Miami-Dade County Product Control Approved", noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been nochange in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in thematerials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed by theexpiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors andshall be available for inspection at the job site at the request of the Building Official.This NOA renews NOA # 18-0412.03 and consists of this page 1 and evidence pages E-1, E-2 & E-3, as well as approval document mentioned above. The submitted documentation was reviewed by Ishaq I. Chanda, P.E.
Ishaq I. Chanda, P.E. Product Control Unit Supervisor
NOA No. 20-0427.08 Expiration Date: June 09, 2025
Approval Date: May 21, 2020 E - 1
International Impact Building Products, LLC
NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED
1. Evidence submitted under previous approvals
A. DRAWINGS1. Manufacturer's die drawings and sections (Submitted under file # below)2. Drawing No. W15-06, titled “Series Titan-50 Alum SLD. Glass Door (L.M.I.)”, sheets 1
through 10 of 10, prepared by AL-Farooq Corporation, dated 02/25/15 and last revised on OCT06, 2015, signed and sealed by Javad Ahmad, P.E.
B. TESTS (Submitted under file # 09-1215.01)1. Test reports on: 1) Air Infiltration Test, per FBC, TAS 202-94
2) Uniform Static Air Pressure Test, Loading per FBC TAS 202-943) Water Resistance Test, per FBC, TAS 202-944) Large Missile Impact Test per FBC, TAS 201-945) Cyclic Wind Pressure Loading per FBC, TAS 203-946) Forced Entry Test, per FBC 2411 3.2.1, TAS 202-94
Along with marked-up drawings and installation diagram of an Aluminum Sliding Glass Door, prepared by Hurricane Testing Laboratory, Inc., Test Report No(s). HTL-0171-0513-09 dated 09/23/09, signed and sealed by Vinu Abraham, P.E. Note: This test report has been revised from originally issue to clarify impact locations, signed & sealed by Vinu Abraham, P.E. 2. Test report No. HTL-0171-0513-09 (sp #1) per TAS 202-94, issued by Hurricane Testing Lab,
signed & sealed by Vinu Abraham, P.E.3 Additional test report No(s) HTL-0171-0713-07 (specimen 4, #5, 5A & 5B) dated 08/01/08,
per TAS 202-94, 201/203-94 (LMI/SMI), issued by Hurricane Testing Lab, signed & sealed by Vinu Abraham, P.E.
C. CALCULATIONS1. Anchor verification calculations and structural analysis, complying with FBC-2014 (5th
Edition), prepared by Al Farooq Corporation, dated 07/01/15, signed and sealed by JavadAhmad, P.E.
2. Glazing complies w/ ASTME-1300-02,-04 & -09.
D. QUALITY ASSURANCE1. Miami Dade Department of Regulatory and Economic Resources (RER).
E. MATERIAL CERTIFICATIONS1. Notice of Acceptance No. 14-0916.11 issued to Kuraray America, Inc. (Former E.I. DuPont
DeNemours & Co., Inc. for the “Sentry Glass ® (Clear and White) Glass Interlayers”,expiring on 07/04/18.
2. Technical strength data of flexible vinyl (Apex 3174) gasket extruded by Melt plastic Int’l Inc.
F. STATEMENTS (Except item #1, all other submitted under file # 09-1215.01)1. Statement letter of conformance to FBC 2014(5th Edition) and letter of no financial interest,
prepared by Al Farooq Corporation, dated 06/03/15, signed and sealed by Javad Ahmad, P.E.
Ishaq I. Chanda, P.E. Product Control Unit Supervisor
NOA No. 20-0427.08 Expiration Date: June 09, 2025
Approval Date: May 21, 2020 E - 2
International Impact Building Products, LLC
NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED
F. STATEMENTS (Continue)3. Lab compliance as part of the above referenced test report.4. Statement letter dated 04/09/09, issued by Plaza Doors of all assets sold to Impact Building
Products, signed by Roy Elwell, president Plaza Door.5. Statement letter dated 04/09/09, issued by Impact Building Products of all assets purchased
from Plaza Doors, signed by Michael Fry, Managing Partner, International Impact BuildingProducts.
G. OTHER1. This NOA revises & renews NOA # 09-1215.01, expired on June 09, 2015.2. Test proposal dated 04/14/09 approved by BCCO.
2. Evidence submitted under previous approval.A. DRAWINGS
1. Drawing No. W15-06 Rev B, titled “Series Titan-50 Alum SLD. Glass Door (L.M.I.)”, sheets1 through 10 of 10, prepared by AL-Farooq Corporation, dated 02/25/15 and last revised onMAR 27, 2018, signed and sealed by Javad Ahmad, P.E.
B. TESTS1. None.
C. CALCULATIONS1. Anchor verification calculations and structural analysis, complying with FBC-2017 (6th
Edition), prepared by Al Farooq Corporation, dated MAR 27, 2018, signed and sealed byJavad Ahmad, P.E.
D. QUALITY ASSURANCE1. Miami Dade Department of Regulatory and Economic Resources (RER).
E. MATERIAL CERTIFICATIONS1. Notice of Acceptance No. 17-0808.02 issued to Kuraray America, Inc. (former E.I. DuPont De
Nemours & Co., Inc.) for “Kuraray Sentry Glass interlayer®”, expiring on 07/04/23.F. STATEMENTS
1. Statement letter of conformance to FBC 6th Edition (2017) and of no financial interest,prepared by Al Farooq Corporation, dated 01/09/18, signed and sealed by Javad Ahmad, P.E.
2. Statement of lab compliance, as part of test report.G. OTHER
1. This NOA revises NOA # 15-0511.02, expiring 07/01/24.
3. New Evidence submitted.A. DRAWINGS
1. Drawing No. W15-06 Rev B, titled “Series Titan-50 Alum SLD. Glass Door (L.M.I.)”, sheets1 through 10 of 10, prepared by AL-Farooq Corporation, dated 02/25/15 and last revised onMAR 27, 2018, signed and sealed by Javad Ahmad, P.E.
B. TESTS1. None.
Ishaq I. Chanda, P.E. Product Control Unit Supervisor
NOA No. 20-0427.08 Expiration Date: June 09, 2025
Approval Date: May 21, 2020 E - 3
International Impact Building Products, LLC
NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED
C. CALCULATIONS (Submitted under #18-0412.03)1. Anchor verification calculations and structural analysis, complying with FBC-2017 (6th
Edition), prepared by Al Farooq Corporation, dated MAR 27, 2018, signed and sealed byJavad Ahmad, P.E.
D. QUALITY ASSURANCE1. Miami Dade Department of Regulatory and Economic Resources (RER).
E. MATERIAL CERTIFICATIONS1 Notice of Acceptance No. 17-0808.02 issued to Kuraray America, Inc. (former E.I. DuPont
De Nemours & Co., Inc.) for “Kuraray Sentry Glass interlayer®”, expiring on 07/04/23. F. STATEMENTS
1. Statement letter of conformance to FBC 6th Edition (2017) and of no financial interest,prepared by Al Farooq Corporation, dated 01/09/18, signed and sealed by Javad Ahmad, P.E.
2. Statement of lab compliance, as part of test report.
G. OTHER1. This NOA renews NOA # 18-0412.03, expiring 06/09/25.
![Hazrat Umar Farooq [R.A]](https://img.dokumen.tips/doc/110x75/5869903b1a28abc7568bf0d3/hazrat-umar-farooq-ra.jpg)
