Mi Air Purifier 2S

User Manual

1 2

Product Overview

Power/Mode Button

Screen On-Off /Filter Reset Button

Laser Dust Sensor

Filter Housing Door

Power Cord Connector

Temperature and Humidity Sensor

Light Sensor

Display

Front Back

Fan Grille

Warning

Do not use under the below circumstances, this may lead to electric shock, fire and other damage：· Unstable places where the unit is easy to topple and fall· High-temperature, humid or wet places such as the bathroom· This appliance can be used by children aged from 8 years and above and persons withreduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved

· Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision

· Prior to cleaning or other maintenance, the appliance must be disconnected from the supply mains

43

Display

The front screen displays instructions

Note: the air purifier automatically adjusts the display brightness based on ambient light.

Auto: automatically switches mode according to indoor air quality

Night: low-noise mode for a quiet night's sleep

Manual: adjusts filtering efficiencyby setting coverage via Mi Home App

25℃60%

025ModeTemperature

Humidity

PM 2.5 readings

Wi-Fi statusAir quality indicator

GreenOrangeRed

0-75 μg/m³76-150 μg/m³150 μg/m³ or higher

The air quality indicator turns green, yellow or red to indicate current air quality

How to Install

Open the filter doorPress to open filter door and make sure the filter is installed in place.

1 Connect to power supplyConnect the power cord to the connector at the bottom of the unit, then plug it into a power supply.

3Take out the power cordRemove the power cord from the bag within the cartridge and close the filter door.

2

65

How to Use

Power / Mode switch

Properly place the air purifierFor optimum performance, maintain the recommended distance between air inlets and walls or other obstacles.

Press the power button to turn the unit on; press again to switch mode; press and hold for 2 sec to turn the unit off.

Screen On / OffPress screen on/off button on the back of the unit to turn on/off the screen.

Note: it is recommended to close doors and windows for better filtering when using the purifier.

20 cm or more

20 cm or more 10 cm or more

Quick Setup

Reset Wi-Fi

Control your device and interact it with other smart home devices in Mi Home app.

1.Install Mi Home app Scan the QR code or go to app store to download and install Mi Home app.

2.Add a deviceOpen Mi Home app, tap "+" on the upper right, and then follow prompts to add your device.

If your phone could not be connected to the air purifier, press both mode button and screen on/off button for 5 secs until you hear a beeping sound indicating that Wi-Fi has been reset.

Note: The version of Mi Home app might have been updated, please follow the instructions based on the current app version.

Note: refer to the "Filter Replacement" label on the back of the filter housing door for detailed instructions.

Filter status prompts

Note: the filter may produce odors when it absorbs excessive harmful gases. You're recommended to store the filter in a place with good lighting and ventilation to improve the activated carbon and restore dust adsorption capacity. if the recommended lifespan is due, please replace the filter in time.

Filter installation promptsNo filter or the filter is not original.

Filter life promptsThe remaining life percentage displays on the screen when the filter's remaining life is more than 10%.

1

2

3 Filter replacement promptsThe filter should be replaced every 3-6 months. When the purifier detects the filter life is less than 10%, the display will prompt you with a QR code and a filter remaining life alert.

Please install the original filter

Filter remaining 98%

Filter remaining 2%

87

How to Maintain

Clean the filter cartridge

Clean the laser dust sensor

To ensure optimum operation, use a vacuum cleaner or soft cloth to remove any dust clinging to air holes or housing walls.

The switch of dust sensor's back cover is at the top of the filter housing. Lift to open the back cover (see Figure A).

Use an air blow gun or hair dryer to clean the back cover grille and sensor (see Figure B).

Make sure to turn off the air purifier and disconnect power before cleaning.

Note: Do not use hot air.

Figure A

Figure B

Specifications

Name Mi Air Purifier 2S Rated voltage 100-240V~ PM CADR 310m3/h

Model AC-M4-AA Rated frequency 50/60Hz PM CCM P3

Item dimensions 240×240×520 mm Rated power 29W Formaldehyde CADR 60m3/h

Net weight approx. 4.5kg Noise level ≤66dB(A) Formaldehyde CCM F3

Effective coverage 21 - 37m2 PM filtering efficiency High Formaldehyde filtering efficiency High

Wireless connectivity Wi-Fi IEEE 802.11 b/g/n 2.4GHz Network standby power consumption < 2.0W

Regulatory compliance information

Europe — EU declaration of conformityWe Beijing Smartmi electronic technology limited, hereby, declares that this equipment is in compliance with the applicable directives and european norms, and amendments.The full text of the EU declaration of conformity is available at the following internet address: https://www.mi.com/en/service/support/declaration.html

Disposal and recycling information

Correct disposal of this product. This marking indicates that this product should not be disposal with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

9

Safety Precaution

Carrying

Installing

Power cord

Using

· Turn off the unit and disconnect power before moving

· The unit will not turn on until the filter door is correctly installed· Maintain 20cm and more between air inlets and walls or other obstacles

· Do not forcibly pinch, bend or twist the power cord in case that it breaks off· Do not pull the power cord when disconnecting power· Use only supported power socketsFollow these instructions to use the power cord and socket to avoid fire, electric shock or damage：

· The power cord must only be connected to supported power sockets· It is strongly advised to use the provided power cord rather than other cords· Disconnect power before servicing or moving the unit· Do not use the provided power cord with other product

· Stop using immediately in the event of unusual sound, bad odor, excessive heat and abnormal fan spin· Do not insert your finger or any objects into any openings· Keep hair and bits of fabric away from the unit, so as not to get involved or block the air inlet and outlet· Do not sit on, lean on or tilt the unit· Ensure sufficient ventilation when using in conjunction with solid fuel appliances to avoid carbon monoxide poisoning

Manufactured by: Beijing Smartmi Electronic Technology Co., Ltd. (a Mi Ecosystem company)Address:11-1102, Office Building Rainbow City, 68 Qinghe Middle Street, Haidian District, Beijing, ChinaFor further information, please go to www.mi.com

Importer:Beryko s.r.o.Na Roudné 1162/76, 301 00 Plzeňwww.beryko.cz