Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
CONTROLLED ENVIRONMENT
www.metalcraftgroup.co.nz
Architectural / Specification EnquiriesPh: 09 274 0408
Mobile: 027 603 1096Email: [email protected]
MetalcraftInsulated Panels
Metecnopanel PIR
MPPIR
DETAIL LIST DateRevision
00 / 24 COVER SHEET
01 / 24 CEILING SUSPENSION 01 1.1 14.12.2018
02 / 24 CEILING SUSPENSION 02 1.1 14.12.2018
03 / 24 FREEZER FLOOR 01 2.0 14.12.2018
04 / 24 FREEZER FLOOR 02 2.0 14.12.2018
05 / 24 FREEZER FLOOR 03 1.1 14.12.2018
06 / 24 PROCESS FLOOR 01 1.1 14.12.2018
07 / 24 PROCESS FLOOR 02 1.1 14.12.2018
08 / 24 PROCESS FLOOR 03 1.1 14.12.2018
09 / 24 PARTITION 01 2.0 14.12.2018
10 / 24 GIRT 01 2.0 14.12.2018
11 / 24 GIRT 02 2.0 14.12.2018
12 / 24 GIRT 03 1.1 14.12.2018
13 / 24 VERTICAL CORNER COOLROOM / FREEZER 1.1 14.12.2018
14 / 24 ROOF TO WALL COOLROOM / FREEZER 01 2.0 14.12.2018
15 / 24 COOLROOM / FREEZER CONNECTION 01 1.1 14.12.2018
16 / 24 FREEZER PARTITION 01 1.1 14.12.2018
17 / 24 COOLROOM / FREEZER CEILING DETAIL 01 2.0 14.12.2018
18 / 24 CEILING TO WALL DETAIL 01 1.1 14.12.2018
19 / 24 TYPICAL WALL JOINT FREEZER / COOLROOM 01 1.1 14.12.2018
20 / 24 FM DETAIL - WALL TO NON-INSULATED FLOOR JOINT 1.1 14.12.2018
21 / 24 FM DETAIL - WALL TO INSULATED WALL JOINT 1.1 14.12.2018
22 / 24 FM DETAIL - WALL TO INSULATED CEILING JOINT 1.1 14.12.2018
23 / 24 ROOF TO WALL CLEAN ROOM 1.0 14.12.2018
24 / 24 PANEL PROFILES AND SIZES 1.1 14.12.2018
FIRE RESISTANT SEALANT
Ø40mm WASHER AND M10 ZP HEX NUT
METALCRAFTMETECNOPANEL PIR
1/2" PVC SPACER TUBE
Ø76mm NYLON MUSHROOM HEAD
GALVANIZED 'L' BRACKET
Ø4mm GALVANIZED WIRE ROPE
GRIPPLE HANG FAST WIREGRIP OR OTHER
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 3.0 / 2017, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed as asingle line for simplicity and is indicative only. Building paper type and method of installation should complywith underlay manufacturers recommendations and NZBC regulations.
CONTROLLED ENVIRONMENT
ScaleDate Sheet
MetalcraftInsulated Panels
Metecnopanel PIR
MPPIR
Rev.
1 : 5
1.1
CEILING SUSPENSION 01
01 / 2414.12.2018
FIRE RESISTANT SEALANT
Ø40mm WASHER ANDM10 ZP HEX NUT
1/2" PVC SPACER TUBE
Ø76mm NYLON MUSHROOM HEAD
GALVANIZED 'L' BRACKET
Ø4mm GALVANIZED WIRE ROPE
GRIPPLE HANG FAST WIREGRIP OR OTHER
Ø5mm STEEL RIVETS @300CRS.
0.55mm COLORSTEEL FLASHING
METALCRAFTMETECNOPANEL PIR
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 3.0 / 2017, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed as asingle line for simplicity and is indicative only. Building paper type and method of installation should complywith underlay manufacturers recommendations and NZBC regulations.
CONTROLLED ENVIRONMENT
ScaleDate Sheet
MetalcraftInsulated Panels
Metecnopanel PIR
MPPIR
Rev.
1 : 5
1.1
CEILING SUSPENSION 02
02 / 2414.12.2018
POLYTHENE SHEET TOPROTECT PANEL WALLS
CONCRETE WEARING SLAB(DESIGN BY OTHERS)
CONDUCTION CUT IN PANEL(CUT SKIN AND REMOVE STRIP)
POLYTHENE SHEET VAPOURBARRIER 250µM (ALL JOINTS
MIN. 150mm LAP WITH ONBEAD OF MASTIC)
POLYSTYRENE H GRADEFLOOR INSULATION
25mm DRY SAND ANDHEATING CABLE
ø6.5mm / 32mm SHUREDRIVES@ 300mm CRS.
ø5mm RIVETS @ 300mm CRS. ANDVAPOUR SEALANT MASTIC
60.5mm x 48mm x 1.8mm ALUMINIUM"F" MOULD
250µM LAYFLAT STRIP
FIRE RESISTANT SEALANT ABOVEAND BELOW POLYTHENE
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 3.0 / 2017, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed as asingle line for simplicity and is indicative only. Building paper type and method of installation should complywith underlay manufacturers recommendations and NZBC regulations.
CONTROLLED ENVIRONMENT
ScaleDate Sheet
MetalcraftInsulated Panels
Metecnopanel PIR
MPPIR
Rev.
1 : 2
2.0
FREEZER FLOOR 01
03 / 2414.12.2018
POLYTHENE SHEET TOPROTECT PANEL WALLS
METALCRAFTMETECNOPANEL PIR
CONCRETE WEARING SLAB(DESIGN BY OTHERS)
CONDUCTION CUT IN PANEL (CUTSKIN AND REMOVE STRIP)
POLYTHENE SHEET VAPOURBARRIER 250µM (ALL JOINTS
MIN. 150mm LAP WITH ONBEAD OF MASTIC)
POLYSTYRENE H GRADEFLOOR INSULATION
ø6.5mm / 32mm SHUREDRIVES@ 300mm CRS.
ø5mm RIVETS @ 300mm CRS. ANDVAPOUR SEALANT MASTIC
60.5mm x 48mm x 1.8mm ALUMINIUM"F" MOULD
250µM LAYFLAT STRIP
FIRE RESISTANT SEALANT ABOVEAND BELOW POLYTHENE
PIPE PIPE
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 3.0 / 2017, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed as asingle line for simplicity and is indicative only. Building paper type and method of installation should complywith underlay manufacturers recommendations and NZBC regulations.
CONTROLLED ENVIRONMENT
ScaleDate Sheet
MetalcraftInsulated Panels
Metecnopanel PIR
MPPIR
Rev.
1 : 2
2.0
FREEZER FLOOR 02
04 / 2414.12.2018
POLYTHENE SHEET TOPROTECT PANEL WALLS
METALCRAFTMETECNOPANEL PIR
CONCRETE WEARING SLAB(DESIGN BY OTHERS)
CONDUCTION CUT IN PANEL(CUT SKIN AND REMOVE
STRIP)
POLYTHENE SHEET VAPOURBARRIER 250µM (ALL JOINTS
MIN. 150mm LAP WITH ONBEAD OF MASTIC)
POLYSTYRENE H GRADEFLOOR INSULATION
25mm DRY SAND ANDHEATING CABLE
ø6.5mm / 32mm SHUREDRIVES@ 300mm CRS.
60.5mm x 48mm x 1.8mm ALUMINIUM"F" MOULD
250µM LAYFLAT STRIP
FIRE RESISTANT SEALANT ABOVEAND BELOW POLYTHENE
GROUT
POLYSTYRENE
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 3.0 / 2017, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed as asingle line for simplicity and is indicative only. Building paper type and method of installation should complywith underlay manufacturers recommendations and NZBC regulations.
CONTROLLED ENVIRONMENT
ScaleDate Sheet
MetalcraftInsulated Panels
Metecnopanel PIR
MPPIR
Rev.
1 : 2
1.1
FREEZER FLOOR 03
05 / 2414.12.2018
METALCRAFTMETECNOPANEL PIR
ø6.5mm / 32mm SHUREDRIVES@ 300mm CRS.
ALUMINIUM COVE BASE
F.F.L.
Ø5mm/16mm RIVETS @300mm CRS WITH FIRERESISTANT SEALANT
ALTERNATIVEOPTION 1
ALTERNATIVEOPTION 2
37.95mm COVING
91.50mm COVING
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 3.0 / 2017, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed as asingle line for simplicity and is indicative only. Building paper type and method of installation should complywith underlay manufacturers recommendations and NZBC regulations.
CONTROLLED ENVIRONMENT
ScaleDate Sheet
MetalcraftInsulated Panels
Metecnopanel PIR
MPPIR
Rev.
1 : 2
1.1
PROCESS FLOOR 01
06 / 2414.12.2018
METALCRAFTMETECNOPANEL PIR
CONCRETE PLINTH
ø6.5mm / 32mm SHUREDRIVES@ 300mm CRS.
ø5mm RIVETS @ 300mm CRS.WITH FIRE RESISTANT SEALANT
ALUMINIUM CHANNEL
F.F.L.
ø5mm RIVETS @ 300mmCRS.
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 3.0 / 2017, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed as asingle line for simplicity and is indicative only. Building paper type and method of installation should complywith underlay manufacturers recommendations and NZBC regulations.
CONTROLLED ENVIRONMENT
ScaleDate Sheet
MetalcraftInsulated Panels
Metecnopanel PIR
MPPIR
Rev.
1 : 2
1.1
PROCESS FLOOR 02
07 / 2414.12.2018
METALCRAFTMETECNOPANEL PIR
ø6.5mm / 32mm SHUREDRIVES@ 300mm CRS.
ø5mm RIVETS @ 300mm CRS.
ALUMINIUM CHANNEL
F.F.L.
FIRE RESISTANT SEALANT
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 3.0 / 2017, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed as asingle line for simplicity and is indicative only. Building paper type and method of installation should complywith underlay manufacturers recommendations and NZBC regulations.
CONTROLLED ENVIRONMENT
ScaleDate Sheet
MetalcraftInsulated Panels
Metecnopanel PIR
MPPIR
Rev.
1 : 2
1.1
PROCESS FLOOR 03
08 / 2414.12.2018
ALUMINIUM CHANNEL
METALCRAFTMETECNOPANEL PIR
ø6.5mm / 32mm SHUREDRIVES@ 300mm CRS.
ø5mm RIVET TO CEILING
40mm x 40mm STEELINTERNAL ANGLE
ø5mm RIVETS @300mm CRS.
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 3.0 / 2017, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed as asingle line for simplicity and is indicative only. Building paper type and method of installation should complywith underlay manufacturers recommendations and NZBC regulations.
CONTROLLED ENVIRONMENT
ScaleDate Sheet
MetalcraftInsulated Panels
Metecnopanel PIR
MPPIR
Rev.
1 : 2
2.0
PARTITION 01
09 / 2414.12.2018
Ø76mm NYLON MUSHROOM HEAD
M10 Z.P THREADED ROD
FIRE RESISTANT SEALANT
GIRT BY METALCRAFT STRUCTURAL
14-20x22 mm CLASS 3 TEKSCREWS (3 PER ANGLE)
METALCRAFTMETECNOPANEL PIR
75mmx76mmx75mm DURAGALANGLE (100mm LONG) OR
ALTERNATIVE BRACKET SEE11/19 & 12/19
1/2" PVC SPACER TUBEONLY IN ROOMS WITHTEMPERATURE LESS THAN 0°c
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 3.0 / 2017, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed as asingle line for simplicity and is indicative only. Building paper type and method of installation should complywith underlay manufacturers recommendations and NZBC regulations.
CONTROLLED ENVIRONMENT
ScaleDate Sheet
MetalcraftInsulated Panels
Metecnopanel PIR
MPPIR
Rev.
1 : 2
2.0
GIRT 01
10 / 2414.12.2018
Ø76mm NYLON MUSHROOM HEAD
M10 Z.P THREADED ROD
FIRE RESISTANT SEALANT
GIRT BY METALCRAFTSTRUCTURAL
METALCRAFTMETECNOPANEL PIR
1/2" PVC SPACER TUBE ONLY INROOMS WITH TEMPERATURELESS THAN 0°c
Ø40mm STEEL WASHER
75 x 5mm DURAGALSTEEL BRACKET
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 3.0 / 2017, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed as asingle line for simplicity and is indicative only. Building paper type and method of installation should complywith underlay manufacturers recommendations and NZBC regulations.
CONTROLLED ENVIRONMENT
ScaleDate Sheet
MetalcraftInsulated Panels
Metecnopanel PIR
MPPIR
Rev.
1 : 2
2.0
GIRT 02
11 / 2414.12.2018
Ø76mm NYLON MUSHROOM HEAD
M10 Z.P THREADED ROD
FIRE RESISTANT SEALANT
GIRT BY METALCRAFTSTRUCTURAL
METALCRAFTMETECNOPANEL PIR
1/2" PVC SPACER TUBEONLY IN ROOMS WITHTEMPERATURE LESS THAN 0°c
Ø40mm STEEL WASHER
DURAGAL STEELBRACKET
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 3.0 / 2017, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed as asingle line for simplicity and is indicative only. Building paper type and method of installation should complywith underlay manufacturers recommendations and NZBC regulations.
CONTROLLED ENVIRONMENT
ScaleDate Sheet
MetalcraftInsulated Panels
Metecnopanel PIR
MPPIR
Rev.
1 : 2
1.1
GIRT 03
12 / 2414.12.2018
METALCRAFTMETECNOPANEL PIR
Ø5mm RIVETS @ 300mm CRS.
40mm x 40mm 0.55mm MIN.FOLDED GALVANIZEDSTEEL ANGLE
40mm x 40mm 0.55mm MIN. FOLDEDGALVANIZED STEEL ANGLE NO SEALANT
Ø5mm RIVETS @ 300mm CRS
Ø5mm RIVETS @ 300mm CRS.WITH SEALANT
FIRE RESISTANT SEALANT
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 3.0 / 2017, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed as asingle line for simplicity and is indicative only. Building paper type and method of installation should complywith underlay manufacturers recommendations and NZBC regulations.
CONTROLLED ENVIRONMENT
ScaleDate Sheet
MetalcraftInsulated Panels
Metecnopanel PIR
MPPIR
Rev.
1 : 2
1.1
VERTICAL CORNER COOLROOM / FREEZER
13 / 2414.12.2018
METALCRAFTMETECNOPANEL PIR
Ø5mm RIVETS @ 300mm CRS.
70mm x 40mm 0.55mm MIN. FOLDEDGALVANIZED STEEL ANGLE
40mm x 40mm 0.55mm MIN. FOLDEDGALVANIZED STEEL ANGLE
METALCRAFT METECNOPANEL
Ø5mm STEEL RIVETS @300mm CRS WITHSEALANT.
COOLROOM / FREEZER
FIRE SEALANT SEALANT
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 3.0 / 2017, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed as asingle line for simplicity and is indicative only. Building paper type and method of installation should complywith underlay manufacturers recommendations and NZBC regulations.
CONTROLLED ENVIRONMENT
ScaleDate Sheet
MetalcraftInsulated Panels
Metecnopanel PIR
MPPIR
Rev.
1 : 2
2.0
ROOF TO WALL COOLROOM / FREEZER 01
14 / 2414.12.2018
COOLROOM SEALANT
METALCRAFTMETECNOPANEL PIR
Ø5mm RIVETS @ 300mm CRS
40mm x 40mm 0.55mm MIN. FOLDEDGALVANIZED STEEL ANGLE
Ø5mm STEEL RIVETS @300mm CRS
40mm x 40mm 0.55mm MIN. FOLDEDGALVANIZED STEEL ANGLE
FIRE RESISTANT SEALANT
METALCRAFTMETECNOPANEL PIR
CONDUCTION CUT IN PANEL(CUT SKIN AND REMOVE STRIP)
COOLROOMFREEZER
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 3.0 / 2017, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed as asingle line for simplicity and is indicative only. Building paper type and method of installation should complywith underlay manufacturers recommendations and NZBC regulations.
CONTROLLED ENVIRONMENT
ScaleDate Sheet
MetalcraftInsulated Panels
Metecnopanel PIR
MPPIR
Rev.
1 : 2
1.1
COOLROOM / FREEZER CONNECTION 01
15 / 2414.12.2018
Ø5mm RIVETS @ 300mm CRS.
40mm x 40mm 0.55mmMIN. FOLDED GALVANIZEDSTEEL ANGLE
40mm x 40mm 0.55mm MIN. FOLDEDGALVANIZED STEEL ANGLE
METALCRAFT METECNOPANELPIR
Ø5mm STEEL RIVETS@ 300mm CRS.
FREEZER FREEZER
METALCRAFT METECNOPANEL PIR
CONDUCTION CUT IN PANEL(CUT SKIN AND REMOVE STRIP)
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 3.0 / 2017, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed as asingle line for simplicity and is indicative only. Building paper type and method of installation should complywith underlay manufacturers recommendations and NZBC regulations.
CONTROLLED ENVIRONMENT
ScaleDate Sheet
MetalcraftInsulated Panels
Metecnopanel PIR
MPPIR
Rev.
1 : 2
1.1
FREEZER PARTITION 01
16 / 2414.12.2018
Ø5mm RIVETS @ 300mm CRS WITHCOOLROOM OR FIRE RESISTANT
SEALANT. DEPENDING ON INTERNALSPREAD OF FLAME REQUIREMENTS
ENGINEERED BY OTHERS
40mm x 40mm 0.55mm MIN. FOLDEDGALVANIZED STEEL ANGLE
METALCRAFTMETECNOPANEL PIR
Ø5mm STEEL RIVETS@ 300mm CRS
CONDUCTION CUT IN PANEL(CUT SKIN AND REMOVE STRIP)
METALCRAFTMETECNOPANEL PIR
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 3.0 / 2017, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed as asingle line for simplicity and is indicative only. Building paper type and method of installation should complywith underlay manufacturers recommendations and NZBC regulations.
CONTROLLED ENVIRONMENT
ScaleDate Sheet
MetalcraftInsulated Panels
Metecnopanel PIR
MPPIR
Rev.
1 : 2
2.0
COOLROOM / FREEZER CEILING DETAIL 01
17 / 2414.12.2018
Ø5mm RIVETS @ 300mm CRS
FIRE RESISTANT SEALANT
80mm x 40mm x 3mm MIN. STEELINTERNAL ANGLE
40mm x 40mm 0.55mm MIN. FOLDEDGALVANIZED STEEL ANGLE
METALCRAFT METECNOPANELPIR
Ø5mm STEEL RIVETS @ 300mm CRS OR ASSPECIFIED BY ENGINEER
CONCRETE
Ø6.5mm / 32 mm SHUREDRIVES@ 300mm CRS. OR ASSPECIFIED BY ENGINEER
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 3.0 / 2017, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed as asingle line for simplicity and is indicative only. Building paper type and method of installation should complywith underlay manufacturers recommendations and NZBC regulations.
CONTROLLED ENVIRONMENT
ScaleDate Sheet
MetalcraftInsulated Panels
Metecnopanel PIR
MPPIR
Rev.
1 : 2
1.1
CEILING TO WALL DETAIL 01
18 / 2414.12.2018
COOLROOM SEALANT
METALCRAFTMETECNOPANEL PIR
INSIDE
OUTSIDE
FIRE RESISTANT SEALANT
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 3.0 / 2017, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed as asingle line for simplicity and is indicative only. Building paper type and method of installation should complywith underlay manufacturers recommendations and NZBC regulations.
CONTROLLED ENVIRONMENT
ScaleDate Sheet
MetalcraftInsulated Panels
Metecnopanel PIR
MPPIR
Rev.
1 : 2
1.1
TYPICAL WALL JOINT FREEZER / COOLROOM 01
19 / 2414.12.2018
METALCRAFTMETECNOPANEL PIR
ø6.5mm / 38mm STEEL SPIKES@ 400mm CRS.
ALUMINIUM COVE BASE
F.F.L.
Ø4mm STEEL RIVETS @300crs
SILICON SEALANT
OUTSIDE INSIDE
ALUMINIUM CHANNEL BASE
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 3.0 / 2017, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed as asingle line for simplicity and is indicative only. Building paper type and method of installation should complywith underlay manufacturers recommendations and NZBC regulations.
CONTROLLED ENVIRONMENT
ScaleDate Sheet
MetalcraftInsulated Panels
Metecnopanel PIR
MPPIR
Rev.
1 : 2
1.1
FM DETAIL - WALL TO NON-INSULATED FLOOR JOINT
20 / 2414.12.2018
METALCRAFTMETECNOPANEL PIR
OUTSIDE INSIDE
60x60 EXTERNAL ANGLE
SEALANT
Ø4mm STEEL RIVETS @300crs
40x40 INTERNAL ANGLE
REBATE CORNER
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 3.0 / 2017, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed as asingle line for simplicity and is indicative only. Building paper type and method of installation should complywith underlay manufacturers recommendations and NZBC regulations.
CONTROLLED ENVIRONMENT
ScaleDate Sheet
MetalcraftInsulated Panels
Metecnopanel PIR
MPPIR
Rev.
1 : 2
1.1
FM DETAIL - WALL TO INSULATED WALL JOINT
21 / 2414.12.2018
METALCRAFTMETECNOPANEL PIR
OUTSIDE
INSIDE
70x50 EXTERNAL ANGLE
SEALANT
Ø4mm STEEL RIVETS @300crs
40x40 INTERNAL ANGLE
REBATE CORNER
300mm MAX
CEILING SUSPENSION
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 3.0 / 2017, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed as asingle line for simplicity and is indicative only. Building paper type and method of installation should complywith underlay manufacturers recommendations and NZBC regulations.
CONTROLLED ENVIRONMENT
ScaleDate Sheet
MetalcraftInsulated Panels
Metecnopanel PIR
MPPIR
Rev.
1 : 2
1.1
FM DETAIL - WALL TO INSULATED CEILING JOINT
22 / 2414.12.2018
METALCRAFT INSULATEDPANEL CEILING
Ø5mm RIVETS @ 300mm CRS.
70mm x 40mm 0.55mm MIN. FOLDEDGALVANIZED STEEL ANGLE
40mm x 40mm 0.55mm MIN. FOLDEDGALVANIZED STEEL ANGLE
METALCRAFT THERMOPANELEPS
Ø5mm STEEL RIVETS @300mm CRS WITHSEALANT.
COOLROOM
FIRE SEALANT SEALANT
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 3.0 / 2017, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed as asingle line for simplicity and is indicative only. Building paper type and method of installation should complywith underlay manufacturers recommendations and NZBC regulations.
CONTROLLED ENVIRONMENT
ScaleDate Sheet
MetalcraftInsulated Panels
Metecnopanel PIR
MPPIR
Rev.
1 : 2
1.0
ROOF TO WALL CLEAN ROOM
23 / 2414.12.2018
A
1100
A= 50, 75, 100, 150,200mm
METECNOPANEL PIR
FINELINE FINISH
SCALE @ 1:5
SCALE @ 1:2
INTERNAL LINER FINISHES
SATINLINE FINISH
STANDARD
15 30
2
20100
3
Reference
DISCLAIMER:All details are to be used for indicative purposes only and the designer should consult both the MRM code ofpractice version 3.0 / 2017, E2 and all other relevant building codesDetails of the supporting mechanisms are indicative only. Compliance of the supporting mechanisms is theresponsibility of the designer. Construction detail can vary for wall cladding. The underlay is detailed as asingle line for simplicity and is indicative only. Building paper type and method of installation should complywith underlay manufacturers recommendations and NZBC regulations.
CONTROLLED ENVIRONMENT
ScaleDate Sheet
MetalcraftInsulated Panels
Metecnopanel PIR
MPPIR
Rev.
As indicated
1.1
PANEL PROFILES AND SIZES
24 / 2414.12.2018