Upload
yehia-kamel
View
239
Download
0
Embed Size (px)
Citation preview
8/3/2019 Metasys CCT Bluetooth Technology Communication Commissioning Guide
1/26
1Metasys CCT Bluetooth Technology Communication Commissioning Guide
Refer to the QuickLIT Web site for the most up-to-date version of this document.
Document Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Related Documentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Wireless Commissioning Converter Laptop Commissioning Overview . . . . . . . . . 4
Bluetooth Wireless Technology Modules and Adapters . . . . . . . . . . . . . . . . . . . . . . . . . 4
Key Laptop Configuration Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Japanese Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
European Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Detailed Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Verifying Your Laptops Bluetooth Wireless State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing the Bluetooth Wireless USB Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Setting Up the Computers Bluetooth Wireless Configuration . . . . . . . . . . . . . . . . . . . 10
Pairing with and Connecting to a Wireless Commissioning Converter . . . . . . . . . . . . 15
Verifying the Connection between the Laptop and the Wireless Commissioning Converter20
Connecting to a Different and Unpaired or Different and Paired Wireless CommissioningConverter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Removing a Network Adapter from the Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Disabling TCP/IP for the Bluetooth Adapter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Uninstalling Network Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Metasys CCT Bluetooth Technology CommunicationCommissioning GuideMS-BTCVT-1 (Wireless Commissioning Converter)
Code No. LIT-12011038Software Release 5.1Issued October 4, 2010
Supersedes January 4, 2010
http://cgproducts.johnsoncontrols.com/default.aspxhttp://cgproducts.johnsoncontrols.com/default.aspx8/3/2019 Metasys CCT Bluetooth Technology Communication Commissioning Guide
2/26
Metasys CCT Bluetooth Technology Communication Commissioning Guide2
8/3/2019 Metasys CCT Bluetooth Technology Communication Commissioning Guide
3/26
Metasys CCT Bluetooth Technology Communication Commissioning Guide 3
Metasys CCT Bluetooth Technology
CommunicationCommissioning Guide
Document Introduction
This document describes how to install the supported Bluetooth wireless
adapters and commission your Controller Configuration Tool (CCT) laptop to
communicate with the Wireless Commissioning Converter.
Note: Microsoft Windows Server 2008 Operating System (OS) does not
support Bluetooth wireless technology. You cannot commission your CCT
laptop for Bluetooth communication if it is running this OS.
This document assumes that you have already installed the CCT software on your
computer. To complete all of the procedures in this document, you must also have
a Wireless Commissioning Converter connected to a powered-on field controller
(refer to the Wireless Commissioning Converter Installation Instructions
[Part No. 24-10108-2]).
Note: The Wireless Commissioning Converter can be used in conjunction with
the ZFR1800 Series Wireless Field Bus System; however, the wireless
technologies of the Wireless Commissioning Converter and the ZFR1800
Series System do not directly interact.
When the Wireless Commissioning Converter is connected on the
hard-wired portion of a Field Controller (FC) Bus, it can be used to
commission and communicate with any field controller, whether it is
hardwired to the FC Bus or wirelessly enabled through the ZFR1800 Series
Wireless Field Bus System.
When the Wireless Commissioning Converter is connected directly to a
wirelessly enabled field controller, it commissions and communicates with
only that controller.
Related Documentation
Table 1 provides a list of documents related to the CCT and the Wireless
Commissioning Converter.
Table 1: Related Documentation
For Information On See Document LIT or Part Number
Installing the CCT Software CCT Installation Instructions LIT-12011529 Connecting the WirelessCommissioning Converter to Hardware;Wireless Commissioning ConverterSpecifications
Wireless Commissioning ConverterInstallation Instructions
Part No. 24-10108-2
Using or Configuring ControllerApplications in the CCT
CCT Help LIT-120111471
1. This LIT number represents a print friendly version of the Help.
http://-/?-http://-/?-8/3/2019 Metasys CCT Bluetooth Technology Communication Commissioning Guide
4/26
Metasys CCT Bluetooth Technology Communication Commissioning Guide4
Wireless Commissioning Converter LaptopCommissioning Overview
To allow the Controller Configuration Tool (CCT) software to connect the
Wireless Commissioning Converter to upload and download field controller
applications, the laptop running CCT must have a Bluetooth wireless adapter
installed and configured.
Once the Bluetooth wireless adapter is installed and configured on the computer,
you do not need to do it again until other software or hardware configurations
change in time. You can perform the procedures to pair with and test connections
to the Wireless Commissioning Converter whenever you need them.
Figure 1 provides an overview of the procedure required to commission your
laptop to allow communication between the Wireless Commissioning Converter
and CCT.
Bluetooth Wireless Technology Modules and Adapters
We recommend that if your computer has internal Bluetooth wireless
communication, you use that method to communicate with the Wireless
Commissioning Converter.
You can commission the following types of laptop computers to communicate with
the Wireless Commissioning Converter:
a laptop computer with an internal Bluetooth wireless module
a laptop computer with a Bluetooth wireless Universal Serial Bus (USB)
adapter
For the latest list of laptop computers with internal Bluetooth wireless modules and
USB adapters, Johnson Controls employees should refer to the Computer Price
List, which is available on the Johnson Controls Portal intranet site by InformationTechnology Acquisition Services (ITAS). Otherwise, please contact your
Johnson Controls representative if you need assistance.
Key Laptop Configuration Guidelines
The instructions to enable Bluetooth wireless communication on your computer
may vary depending on your computer and the type and brand of Bluetooth
wireless adapter you are using; however, always observe the following guidelines
when configuring your laptop to communicate with the Wireless Commissioning
Converter:
Disable the Discovery and Accessibility options for the Bluetooth wirelessdevice to ensure the security of your computer.
http://-/?-http://-/?-8/3/2019 Metasys CCT Bluetooth Technology Communication Commissioning Guide
5/26
Metasys CCT Bluetooth Technology Communication Commissioning Guide 5
Figure 1: Commissioning Overview
Does your laptopcomputer have the ability to use
internal Bluetooth wirelesscommunication?
Install the Bluetooth wireless USB adapter.See Installing the Bluetooth Wireless USB
Adapter.
Does yourlaptop have an internal
Bluetooth wireless moduleinstalled?
No
NoYes
The Wireless Commissioning Converter isready to be used by the CCT.
Yes
converter_commissioning
Order and install the correct module and
drivers. See Verifying Your LaptopsBluetooth Wireless State.
Verify the connection between the laptopand the Wireless Commissioning Converter.See Verifying the Connection between theLaptop and the Wireless Commissioning
Converter.
Set up the computers Bluetooth wirelessconfiguration. See Setting Up theComputers Bluetooth Wireless
Configuration.
If you are not sure about your laptopswireless capabilities, see Verifying Your
Laptops Bluetooth Wireless State.
Pair with a Wireless CommissioningConverter and connect to its
COM port. See Pairing with and Connectingto a Wireless Commissioning Converter.
8/3/2019 Metasys CCT Bluetooth Technology Communication Commissioning Guide
6/26
Metasys CCT Bluetooth Technology Communication Commissioning Guide6
Disable any refresh timers in the Bluetooth device connection manager
software. This prevents the Bluetooth device from auto-discovering any other
Bluetooth devices that may be in range. While the computer performs
auto-discovery, you cannot establish a connection to the Wireless
Commissioning Converter.
We recommend that you change your computers Bluetooth Friendly Name or
Computer Name to BLUETOOTH. This anonymous name prevents someonewho discovers your computer from determining to whom the computer
belongs.
Note: If Discovery and Accessibility are disabled, the computer cannot be
discovered by another device.
When installing a USB device, do not plug the device into the USB port until
the software or instructions prompt you to do so. This is important for any USB
device to ensure that the default Microsoft Windows software USB drivers
are installed correctly.
If your computer already has built-in Bluetooth wireless capability, we
recommend that you do not use an external Bluetooth wireless adapter. Do notuse Bluetooth wireless adapters from different vendors on the same computer
as this may cause operational problems. Vendors may use the same core
Bluetooth technology chipset, and multiple versions on your computer may
interfere with each other and cause operational problems.
If your laptop already has the Bluetooth wireless module pre-installed, verify
the configuration. See Setting Up the Computers Bluetooth Wireless
Configuration. If not, see Verifying Your Laptops Bluetooth Wireless State.
Bluetooth wireless devices on the computer typically provide two virtual COM
ports. Only the Client COM port is able to connect to the Wireless
Commissioning Converter. The Server/Local COM port is not required andcannot be used to connect to the Wireless Commissioning Converter.
Bluetooth wireless device installation software typically installs all of the
Bluetooth services such as Local Area Network (LAN) services, Dial-up
Networking, fax, and so on. These services are not required, but you can install
them, if desired; however, only the Bluetooth Serial Port service is required
by the Wireless Commissioning Converter.
Note: Some Bluetooth services may cause interoperability issues with
software on your computer. We recommend that you install the
Bluetooth Serial Port service and not install services with which you
are unfamiliar.
We recommend that you use the same Wireless Commissioning Converter with
the same laptop computer. Otherwise, you must repeat the
pairing/authentication process between the laptop and the Wireless
Commissioning Converter. See Setting Up the Computers Bluetooth Wireless
Configuration. Similarly, do not share Bluetooth wireless adapters among
computers.
8/3/2019 Metasys CCT Bluetooth Technology Communication Commissioning Guide
7/26
Metasys CCT Bluetooth Technology Communication Commissioning Guide 7
You can connect to the Wireless Commissioning Converter using the Bluetooth
wireless adapter and a program such as HyperTerminal software; however,
the Wireless Commissioning Converter recognizes that an incorrect application
is attempting to pass data through it and automatically disconnects. Only
Metasys system applications that provide Master-Slave/Token-Passing
(MS/TP) communications bus support can maintain a connection with the
Wireless Commissioning Converter.
Note: A wireless utility is provided with the CCT to verify the status of the
wireless connection.
Typical connection times between the Wireless Commissioning Converter and
the computer Bluetooth device are within 1 to 4 seconds. The range between
the devices is guaranteed up to 30 ft (9 m); however, a line of sight connection
may extend up to 200 ft (61 m).
If you download the installation software from the USB adapter
manufacturers Web site, be sure to download the latest version posted.
Japanese Considerations
Japanese law requires certification for all Bluetooth wireless devices. The Wireless
Commissioning Converter is certified for use in Japan; however, to use the
Wireless Commissioning Converter in Japan, your Bluetooth wireless adapter
must also be certified. Purchase a Japanese certified Bluetooth wireless adapter in
Japan for use with the Wireless Commissioning Converter.
European Considerations
European law requires that Bluetooth wireless devices comply with the Restriction
of Hazardous Substances in Electrical and Electronic Equipment (RoHS) Directive
(2002/95/EC). The Wireless Commissioning Converter complies with this
directive; however, to use the Wireless Commissioning Converter in Europe, youmust use a RoHS-compliant Bluetooth adapter.
8/3/2019 Metasys CCT Bluetooth Technology Communication Commissioning Guide
8/26
Metasys CCT Bluetooth Technology Communication Commissioning Guide8
Detailed Procedures
Verifying Your Laptops Bluetooth Wireless State
If your computer has built-in Bluetooth wireless capability, we recommend that
you do not use an external Bluetooth wireless adapter.
To verify your laptops Bluetooth wireless state:
1. Verify if you have a Bluetooth icon on your system tray.
If the icon is blue and white, you have an internal Bluetooth module already
installed. Go to Setting Up the Computers Bluetooth Wireless Configuration.
If you do not have an icon, or if the icon is blue and red, continue.
2. Work with your local Information Technology (IT) support to order and install
the correct internal Bluetooth wireless module and drivers.
Note: The wireless antenna button on the laptop toggles both the internal
Bluetooth wireless module and the internal wireless LAN module on and
off. If you have an internal Bluetooth wireless module and the blueLight-Emitting Diode (LED) is off, press the wireless antenna button to
turn on the Bluetooth module. The blue LED also lights up to indicate that
the laptop is using its internal antenna.
Note: The Bluetooth wireless module driver is usually provided with the module
and available from the manufacturers Web site (for example, find an
HP driver at www.hp.com).
Before you can begin using the Bluetooth device, you must configure and set up
the device. Go to Setting Up the Computers Bluetooth Wireless Configuration.
Installing the Bluetooth Wireless USB Adapter
Note: The instructions to install the USB adapter may vary depending on the
vendor of the USB Adapter. Before installing the USB adapter, familiarize
yourself with the vendors installation instructions.
To install the Bluetooth wireless USB adapter:
1. Close all programs and insert the USB Adapter Installation media. The
installation program appears.
Note: If the installation does not start automatically, on the Start menu, click
Run. In the field that appears, enter the vendor setup program, for
example D:\setup.exe (where D is the letter of your CD-ROM or DVD
drive).
2. Click Install Bluetooth Driver. The installation begins and the welcome
screen appears.
IMPORTANT: Do not plug in the USB adapter until prompted to do so. If you
plug in the USB adapter before prompted, seeDuring the installation, you
plugged in the Bluetooth Wireless Adapter before prompted to do so.
http://-/?-http://-/?-http://-/?-http://-/?-http://www.hp.com/http://www.hp.com/8/3/2019 Metasys CCT Bluetooth Technology Communication Commissioning Guide
9/26
Metasys CCT Bluetooth Technology Communication Commissioning Guide 9
3. Click Next. The License Agreement screen appears.
4. To accept the terms of the license agreement, select I accept the terms in the
license agreement and clickNext. The Destination Folder screen appears.
5. Click Next. The Ready to Install the Program screen appears.
6. Click Install. The program installs.
Note: During the installation process, you may see a Driver Signature Noticedialog box saying no certification program is in place for Bluetooth
devices. If this appears, click OK.
7. When the Bluetooth device not found dialog box appears, click Cancel.
Note: You may also be prompted to plug in your USB hardware, which starts
the Found New Hardware Wizard. Wait until the Windows Found New
Hardware Wizard is complete before clicking OK. If you are not
prompted to plug in the USB hardware, wait until the driver installation
is complete before you plug in the USB hardware.
Note: Depending on the adapter you install, you may be prompted to enter a
security code (Figure 2). If so, clickNo and follow the on-screen
directions to enter the code manually. The code is labeled SK and is
printed on the back of the Bluetooth wireless adapter.
8. After the software has been successfully installed, click the Finish button to
close the final window. The red Bluetooth icon appears on the system tray.
9. Plug in the USB adapter. The Found New Hardware Wizard appears.
Note: Your computer may install the driver automatically without the Found
New Hardware Wizard. If it does, restart the computer (if prompted)
and go to Setting Up the Computers Bluetooth Wireless Configuration.
10. Select Install from a list or a specific location and clickNext. The Please
choose your search and installation options screen appears.
11. Select Search for the best driver in these locations and clickNext. The
Completing the New Found Hardware Wizard screen appears.
12. Click Finish. The Bluetooth icon on the system tray turns white.
13. Ensure that your Bluetooth device is connected to your computer (plug it in if
not already prompted) and restart your computer.
Figure 2: Bluetooth Software Dialog Box Requesting Security Code
8/3/2019 Metasys CCT Bluetooth Technology Communication Commissioning Guide
10/26
Metasys CCT Bluetooth Technology Communication Commissioning Guide10
14. After restarting your computer, wait a few seconds for the Bluetooth icon on
your system tray to change from red to white.
Before you can begin using the Bluetooth device, you must configure and set up
the device. Go to Setting Up the Computers Bluetooth Wireless Configuration.
Setting Up the Computers Bluetooth Wireless Configuration
Note: The instructions to set up the computers Bluetooth wireless configurationmay vary slightly depending on the vendor of the Bluetooth wireless
device. The screen capture figures in this section are representative of a
typical installation, but may not match exactly your configuration screens.
Familiarize yourself with the Key Laptop Configuration Guidelines.
To set up the computers Bluetooth wireless configuration:
1. Plug in your Wireless Commissioning Converter to an MS/TP bus and verify
that the Power Light-Emitting Diode (LED) is green, the Fault LED is off, and
the SA/FC Bus LED is blinking.
Note: The Wireless Commissioning Converter you use during this procedure
should be the one you intend to use when uploading and downloading
controllers. This procedure allows your computer to recognize the
Wireless Commissioning Converters Bluetooth Device Address
(BDA) and store the Wireless Commissioning Converters Personal
Identification Number (PIN) Code. If you connect to a different
Wireless Commissioning Converter after this, you are prompted to
enter the Wireless Commissioning Converters PIN Code before you
can connect to it.
2. Right-click on the Bluetooth icon on your system tray and clickStart Using
Bluetooth from the pop-up menu. The Initial Bluetooth Configuration Wizard
appears.
8/3/2019 Metasys CCT Bluetooth Technology Communication Commissioning Guide
11/26
Metasys CCT Bluetooth Technology Communication Commissioning Guide 11
3. Click Next. The Device Name and Type screen appears.
4. Type BLUETOOTH (all capital letters) in the Computer name field and click
Next.TheInitial Bluetooth Configuration Wizard screen appears.
5. Click Next. The Choose the services that this computer will offer screenappears.
6. Clear the selection (remove the check mark) from all services and clickNext.
The Initial Bluetooth Configuration Wizard screen appears.
7. Click Skip when asked if you want to set up more Bluetooth devices. The
Initial Bluetooth Configuration Wizard screen appears.
8. Click Finish.
Figure 3: Example of My Bluetooth Places, Microsoft Windows XPProfessional Operating System (OS)
8/3/2019 Metasys CCT Bluetooth Technology Communication Commissioning Guide
12/26
Metasys CCT Bluetooth Technology Communication Commissioning Guide12
9. Right-click the Bluetooth icon on the system tray and select Advanced
Configuration from the pop-up menu.The Bluetooth Configuration property
sheet appears (Figure 4).
Figure 4: Bluetooth Configuration Property Sheet General Tab
8/3/2019 Metasys CCT Bluetooth Technology Communication Commissioning Guide
13/26
Metasys CCT Bluetooth Technology Communication Commissioning Guide 13
10. Click on the Accessibility tab and verify that the Let other Bluetooth devices
discover this computer option is not selected (Figure 5).
11. Click on the Discovery tab and verify that the Look for other Bluetooth
devices option is not selected (Figure 6).
Figure 5: Bluetooth Configuration Property Sheet Accessibility Tab
Figure 6: Bluetooth Configuration Property Sheet Discovery Tab
http://-/?-http://-/?-8/3/2019 Metasys CCT Bluetooth Technology Communication Commissioning Guide
14/26
Metasys CCT Bluetooth Technology Communication Commissioning Guide14
12. Click the Client Applications tab and highlight Bluetooth Serial Port and
clickProperties (Figure 7). The Bluetooth Properties dialog box appears
(Figure 8) and displays the COM port where the wireless adapter is installed.
Figure 7: Bluetooth Configuration Property Sheet ClientApplications Tab
http://-/?-http://-/?-8/3/2019 Metasys CCT Bluetooth Technology Communication Commissioning Guide
15/26
Metasys CCT Bluetooth Technology Communication Commissioning Guide 15
Note: The COM port specified here is used by the CCT to communicate with
the Wireless Commissioning Converter. Your COM port may be
different from this example.
13. ClickOK to assign the port number to your Bluetooth serial port.
14. ClickOK to close the Bluetooth Configuration property sheet.
15. To pair with and connect to a Wireless Commissioning Converter, continuewith Pairing with and Connecting to a Wireless Commissioning Converter.
Pairing with and Connecting to a Wireless CommissioningConverter
When you pair with a Wireless Commissioning Converter, the computer stores the
Wireless Commissioning Converter password in the configuration. This pairing
allows you to connect to the Wireless Commissioning Converter in the future
without reentering the password.
You can pair with multiple Wireless Commissioning Converters, but you can only
connect to one converter at a time.
To pair with and connect to a Wireless Commissioning Converter:
1. Right-click the Bluetooth iconon your system tray and select Explore My
Bluetooth Places from the pop-up menu. My Bluetooth Places explorer
window appears (Figure 3).
Figure 8: Bluetooth Properties Showing the COM Port Used by the CCT
8/3/2019 Metasys CCT Bluetooth Technology Communication Commissioning Guide
16/26
Metasys CCT Bluetooth Technology Communication Commissioning Guide16
2. Click View devices in range (or double-clickFind Bluetooth Devices). All
discoverable Bluetooth devices within range of your Bluetooth USB adapter
appear (Figure 9). Wireless Commissioning Converter devices appear with the
formatMS-BTCVT-.
Note: If the Wireless Commissioning Converter does not appear in the list,
verify that your computer is searching for and showing all
Bluetooth devices and not just computers.Note: The Question mark device icon is the standard icon for the Wireless
Commissioning Converter.
Figure 9: Entire Bluetooth Neighborhood Showing the WirelessCommissioning Converter
http://-/?-http://-/?-8/3/2019 Metasys CCT Bluetooth Technology Communication Commissioning Guide
17/26
Metasys CCT Bluetooth Technology Communication Commissioning Guide 17
3. Right-click the Wireless Commissioning Converter that corresponds to your
Wireless Commissioning Converter (the BDA is printed on the label on the top
of the Wireless Commissioning Converter) and select Pair Device (Figure 10).
The Bluetooth PIN Code Request dialog box appears (Figure 11).
4. Type BTCVT (case sensitive) in the Bluetooth PIN Code field and clickOK.
Figure 10: Pair Device Option
Figure 11: Bluetooth PIN Code Request Dialog Box
8/3/2019 Metasys CCT Bluetooth Technology Communication Commissioning Guide
18/26
Metasys CCT Bluetooth Technology Communication Commissioning Guide18
5. Right-click the paired Wireless Commissioning Converter (as indicated by the
check mark) and select Discover Available Services (Figure 12). The serial
port service discovery page appears and shows the communications port of
your Wireless Commissioning Converter (Figure 13).
Note: The COM port in this window represents the COM port on the Wireless
Commissioning Converter (and it is always 1), not the COM port of
your laptops Bluetooth wireless adapter.
Figure 12: Discover Available Services
http://-/?-http://-/?-8/3/2019 Metasys CCT Bluetooth Technology Communication Commissioning Guide
19/26
Metasys CCT Bluetooth Technology Communication Commissioning Guide 19
6. Right-click your Wireless Commissioning Converter COM port and click
Connect to Bluetooth Serial Port to make a connection. A COM1 dialog box
appears (Figure 14) and lists your computers COM port and the BDA of the
Wireless Commissioning Converter.
Figure 13: Serial Port Page Showing the Wireless Commissioning Converter
Figure 14: COM1 Dialog Box
8/3/2019 Metasys CCT Bluetooth Technology Communication Commissioning Guide
20/26
Metasys CCT Bluetooth Technology Communication Commissioning Guide20
7. Click OK to dismiss the COM1 dialog box. After making a connection, both
the serial port icon and the Bluetooth icon on your system tray turn green
(Figure 15).
Note: This connection lasts up to 60 seconds before the Wireless
Commissioning Converter realizes that a valid Metasys application is
not using the connection and breaks the link. You can now go on to the
CCT to make a connection to your Wireless Commissioning Converter.
Verifying the Connection between the Laptop and the WirelessCommissioning Converter
If you want to test the connection and see the signal quality between your laptop
and the Wireless Commissioning Converter before using the CCT to download orupload a controller, follow this procedure.
To verify the connection between the laptop and the Wireless Commissioning
Converter:
1. On the Start menu, click Programs > Johnson Controls > Metasys > Bluetooth
Wireless Utility. The Wireless Utility appears.
Figure 15: Serial Port Page Showing the Wireless Commissioning Converterwith Green Icon
8/3/2019 Metasys CCT Bluetooth Technology Communication Commissioning Guide
21/26
Metasys CCT Bluetooth Technology Communication Commissioning Guide 21
2. Enter the COM Port assigned to the Adapter and clickConnect. The Bluetooth
wireless link should establish within seconds.
Note: The Bluetooth wireless adapters COM port appears on the Client
Application tab of the Bluetooth Configuration Property Sheet
(Figure 7). See Cannot communicate with the Serial Port.
3. Click on the Status tab to view the signal quality (Figure 16) and compare your
results to Table 2.
Table 2: Wireless Link Status
Color (Percent) Status1
1. The Wireless Link Status is a measure of the signal strength and does not relate to thetransmission speed of wireless communication.
Description and Corrective Action
Green (70 - 100%) Good Wireless Link is good and sufficient for use with CCT. Nocorrective action required.
Yellow (40 - 60%) Fair Wireless Link is fair and sufficient for use with CCT. Nocorrective action required.
Red (0 - 30%) Poor Wireless is poor and insufficient for use with WirelessCommissioning Converter. Try moving laptop closer tothe Wireless Commissioning Converter or look forsources of interference.
No Bar Disconnected Wireless link not established or connection broken.Verify settings and try to connect to the WirelessCommissioning Converter again.
Figure 16: BTCVT Wireless Utility Status Tab
http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-http://-/?-8/3/2019 Metasys CCT Bluetooth Technology Communication Commissioning Guide
22/26
Metasys CCT Bluetooth Technology Communication Commissioning Guide22
4. Close the Bluetooth Wireless Utility before using the CCT to upload or
download a controller. We do not recommend using this program while
uploading or downloading.
Connecting to a Different and Unpaired or Different and PairedWireless Commissioning Converter
The CCT always attempts to connect to the Wireless Commissioning Converter towhich it was last connected. If you want to force the CCT to connect to a different
Wireless Commissioning Converter, use the following instructions.
To connect to a different, unpaired Wireless Commissioning Converter, see
Pairing with and Connecting to a Wireless Commissioning Converterwith the
Wireless Commissioning Converter you want the CCT to use.
To connect to a different, paired Wireless Commissioning Converter:
1. Right-click the Bluetooth icon on your system tray and select Explore My
Bluetooth Places from the pop-up menu. My Bluetooth Places explorer
window appears (Figure 3).
2. Click View devices in range (or double-clickFind Bluetooth Devices). All
discoverable Bluetooth devices within range of your Bluetooth USB adapter
appear (Figure 9). Wireless Commissioning Converter devices appear with the
formatMS-BTCVT-.
3. Right-click the Wireless Commissioning Converter that corresponds to your
Wireless Commissioning Converter (the BDA is printed on the label on the top
of the Wireless Commissioning Converter) and select Connect COM1. A
COM1 dialog box appears (Figure 14) and lists your computers COM port and
the BDA of the Wireless Commissioning Converter.
4. Click OK to dismiss the COM1 dialog box.
5. Right-click the Wireless Commissioning Converter to which you are connected
and select Disconnect COM1. A COM1 dialog box appears asking if you want
to disconnect.
6. Click Yes. The laptop disconnects from the Wireless Commissioning
Converter.
The CCT attempts to connect to this Wireless Commissioning Converter.
http://-/?-http://-/?-8/3/2019 Metasys CCT Bluetooth Technology Communication Commissioning Guide
23/26
Metasys CCT Bluetooth Technology Communication Commissioning Guide 23
Removing a Network Adapter from the Computer
If you have multiple network adapters on your computer, you may experience long
delays when attempting to access the User Interface (UI). You may also experience
other network communication delays. To work around these connection problems,
either disable the Transmission Control Protocol/Internet Protocol (TCP/IP) for the
Bluetooth adapter or uninstall network access for the Bluetooth connection when
accessing the Metasys UI.After disabling the TCP/IP for the Bluetooth adapter or uninstalling network
access, the Bluetooth connection continues to work as expected for Metasys
network applications.
Disabling TCP/IP for the Bluetooth Adapter
To disable TCP/IP:
1. On the Control Panel, select Network Connections.
2. Right-click the Bluetooth adapter network connection and select Properties.
3. Clear the check-box for TCP/IP.4. Click OK.
Uninstalling Network Access
To uninstall network access:
1. Right-click the Bluetooth icon in the taskbar (Figure 17) and select Bluetooth
Setup Wizard. The Bluetooth Setup window appears (Figure 18).
2. Select the third radio button from the top: I want to configure the Bluetooth
services that this computer will provide to remote devices.
Figure 17:Bluetooth
Icon
Figure 18: Bluetooth Setup Window
http://-/?-http://-/?-http://-/?-http://-/?-8/3/2019 Metasys CCT Bluetooth Technology Communication Commissioning Guide
24/26
Metasys CCT Bluetooth Technology Communication Commissioning Guide24
3. Click Next. The Bluetooth Service Selection window appears.
4. Make sure the Network Access check box is cleared (Figure 19).
5. Click Finish.
Figure 19: BlueTooth Service Selection Window
http://-/?-http://-/?-8/3/2019 Metasys CCT Bluetooth Technology Communication Commissioning Guide
25/26
Metasys CCT Bluetooth Technology Communication Commissioning Guide 25
Troubleshooting
Table 3: Common Problems and Descriptions (Part 1 of 2)
Problem Description/Solution
You are experiencing longdelays when attempting toaccess the UI or you areexperiencing other network
communication delays.
Multiple network adapters on your computer can cause interoperability issuesand/or communications delays. To work around this issue, either disable theTCP/IP or uninstall network access for the Bluetooth connection. SeeRemoving a Network Adapter from the Computer.
During the installation, youplugged in the BluetoothWireless Adapter beforeprompted to do so.
If you plug in the USB Bluetooth adapter before the installation softwareprompts you to do so, the computer may install its own Bluetooth drivers andmay not communicate properly with the Bluetooth adapter. If this occurs, usethe following recovery procedure:
1. Unplug the Bluetooth wireless adapter.2. On the Start menu, click Run and type %windir%\inf3. Rename the BTH.inf file to BTH.bak4. Uninstall the Bluetooth software from Add/Remove Programs.5. Reboot the computer.6. Reinstall the Bluetooth wireless adapter as specified in this document.
See Installing the Bluetooth Wireless USB Adapter.
Cannot communicate withthe Serial Port.
If you cannot communicate with the Serial COM port on which the WirelessAdapter is installed, use the following procedure to verify the COM port usedby the Bluetooth wireless adapter.
1. Right-click the Bluetooth icon on the system tray and select AdvancedConfiguration.
2. Select the Client Applications tab.3. Read the COM port from the Bluetooth Serial Port application.
Cannot communicate withthe Wireless CommissioningConverter from the CCT.
Use the BTCVT Wireless Utility and verify that you are using the correct COMport.
The CCT attempts to communicate with the last Wireless CommissioningConverter to which it connected. If this is not the Wireless CommissioningConverter you are trying to connect to, see Connecting to a Different andUnpaired or Different and Paired Wireless Commissioning Converter.
Bluetooth Wireless enabledlaptop cannot communicatewith the WirelessCommissioning Converter.
Verify that the blue wireless LED is on and that the Bluetooth wireless icon onthe Taskbar is white. If the Blue wireless is off and the Bluetooth icon is red,press the laptops wireless antenna button.
A paired WirelessCommissioning Converterprompts you for the PINcode.
The Wireless Commissioning Converter holds a finite number of paireddevice addresses in internal memory. At this time there is no way to clear thepaired device addresses and there is no workaround; however, once youenter the PIN Code, as prompted, the laptop computer communicates withthe Wireless Commissioning Converter.
8/3/2019 Metasys CCT Bluetooth Technology Communication Commissioning Guide
26/26
Metasys and Johnson Controls are registered trademarks of Johnson Controls, Inc.
All other marks herein are the marks of their respective owners. 2010 Johnson Controls, Inc.
Building Efficiency
507 E. Michigan Street, Milwaukee, WI 53202
On a computer alreadyconfigured to use the USBBluetooth adapter, the FoundNew Hardware Wizardappears when you plug theUSB Bluetooth adapter back
into the USB port.
If you unplug the already configured USB Bluetooth wireless adapter fromyour computer and then plug it into a different USB port on the samecomputer (for example, if you move the adapter from your laptop to yourdocking station or if you plug it into a different USB port), the Found NewHardware Wizard appears.
If the Found New Hardware Wizard appears:
1. Select Install the software automatically (Recommended), and clickNext. The wizard reconfigures the computer to use the adapter on thenew USB port.
2. Click Finish.
When attempting to connectto the BTCVT with my laptop,this error message displays:
The COM1 connection failed.Could not connect to remotedevice.
The Bluetooth Driver for the laptop is not fully compatible with the BTCVTdevice. Contact your Network Technologist (network help desk) forassistance, or go to the manufacturers Web site (for example, find an HPdriver at www.hp.com) to download the compatible driver. Remove the olddrivers before installing the new drivers.
I am unable to pair ormaintain pairing with myBTCVT device.
Table 3: Common Problems and Descriptions (Part 2 of 2)
Problem Description/Solution