Mesh Training

Compex MeSH@work Introduction & Training Session22nd Jan, 2013

Agenda

1. Features2. How to set up the mesh network3. Advanced configuration4. Performance test5. Scenarios

1. FEATURES

What is Mesh?

Mesh@worK technology employs MeshPoints to create a wider coverage from various gateways

Highly secured backhaul links, coupled with 11n technology, gives customers a seamless wireless experience

With a CloudController, customers can easily monitor their networks and quickly detect unusual activities

Features

Advantages of mesh

Secured, high speed coverage Secured, high speed backhaul Increased redundancy

Features

Easy management and configuration Reports Hotspot

User Access Conditions

Open (default) User Agreement (splash page) Hotspot@worK (only in MeshController) Customized Internet Access Controller

available soon

Features

HOTSPOT

Compex wireless mesh network with internet connection -> wireless hotspot with a billing system

Features

WHAT IS MESHSPAN?

Long Distance Outdoor Mesh MeshSpan nodes, located several

kilometers apart, link up to form a mesh backhaul network.

Each MeshSpan node consists of several Compex MeshPods (MPJ72) interconnected through Ethernet switches, mounted on the pole and installed on high-rise buildings and towers.

Features

ADVANTAGES OF MESHSPAN

Form a large outdoor mesh, overcoming antenna limitations Link up to 2km

Features

MeshSpan

*MeshSpan consists of multiple MeshPods

2km 2km

2km

2km

2km

2km

Meshspan network

REPORT OF MESHPOINT

Features

Performance over time

REPORT OF MESHPOINT

Users Log Per MeshPoint Report

Users Log vs Time Report

The RSSI value = the user’s connection signal strength with that MP

Features

2. How to set up a mesh network

Equipments

MeshPoint MP546

Specs Dual radio (5GHz, 2.4GHz) 802.11n, 26dBm TxPower(aggregate) @5GHz, 20dBm TxPower (aggregate)@ 2.4GHz 2x2 2dBi omni antenna, 24VDC power adapter, 802.3af POE Compatible

Mesh type Indoor mesh node

Application Suitable for medium to high application access

EQUIPMENTS

Equipments

MeshPoint MPE72

Specs Single radio 2.4GHz 802.11n, 26dBm TxPower (aggregate), 2x 2dBi omni antenna, 24VDC power adapter, 24V passive POE compatible

Mesh type Indoor mesh node

Application Suitable for low application access, internet web browsing

EQUIPMENTS

Equipments

MeshPoint MPS546

Specs Dual radio (2.4GHz, 5GHz) 802.11n, 29dBm TxPower(aggregate), Built-in [email protected] / 7dBi@5GHz dual polarized omni-directional antenna, 24VDC power adapter, 802.3af POE Compatible

Mesh type Outdoor mesh Backhaul and Coverage MP

Application Long distance connection, up to 300m Suitable for medium to high access applications.

EQUIPMENTS

Equipments

MeshPoint MPS72

Specs Single radio (2.4GHz) 802.11n, 26dBm TxPower(aggregate), Built-in 6.5dBi dual polarized omni-directional antenna, 24VDC power adapter, 24V passive POE Compatible

Mesh type Outdoor Coverage MP

Application Long distance connection, up to 300m. Suitable for low application access, internet web browsing

EQUIPMENTS

Equipments

MeshPod MPJ72

Specs Single radio (5GHz) 802.11n, 29dBm TxPower(aggregate), Built-in 17dBi dual polarized directional antenna, 24VDC passive POE Compatible

Mesh type Outdoor MeshSpan Backhaul link

Application Long distance connection, up to 5km with good transfer speed

EQUIPMENTS

Equipments

MC100

Specs Manage up to 15 Mesh nodes, 100 Users Internal Flash drive storage. 24VDC power adapter

Mesh type MeshController (Table top low profile model)

Application CloudManager and Hotspot Manager, Broadband Aggregation.

EQUIPMENTS

Equipments

MC100

Specs Manage up to 30 Mesh nodes, 100 Users Internal Hard Disk storage 110VAC/240VAC power input

Mesh type MeshController (Rack mount, 1U type)

Application CloudManager and Hotspot Manager, Broadband Aggregation.

EQUIPMENTS

Setting up Mesh Network

SETUP

Check in status

Rebooting and reconfiguring MeshPointsDuring the reboot, the MeshPoints become inactive

Mesh Management page will display the status of the MeshPoints with this icon

After the MeshPoints are up again their icon status will change mesh nodes are indIcated with the icon gateways indicated with the icon

SETUP

LED Status

MeshPoints front display

SETUP

LED Status

SETUP

Gateway

Repeater

MeshController(MC100/MC200)

3. ADVANCED CONFIGURATION

Advanced Configurations

No reboot if no Controller

In a standard network setup the MPs and MPod will check-in once every 5 minutes to the controller.

If it fails to check-in it could mean device has lost the connection and will automatically reboot to recover. This can cause a network disconnection.

To disable the automatic reboot action for all the MPs and MPods, add a tick in the box.

If you do not use a controller to manage your network, you must add a tick in this box and all MPs and MPods will stop the automatic reboot. The MeshPoint meant to be a gateway would need to be configured too.


Transmit Power

Allows you to adjust all MPs coverage radio to this transmit power value.

Adjustment is in steps of 1dBM lower from maximum power. * Note: For Single Radio MeshPoint, changing the coverage transmit

power also change the backhaul transmit power.


SSH password

Entering a new password will change the SSH password of all MPs and MPods to this new password.


Freeze Firmware

When the box is ticked, all MPs automatic firmware update will be disabled.

When the box is not ticked, all MPs can do automatic firmware update when a new firmware file is found in the path set in the Firmware Server box.


Channel Spectrum Bandwidth

Allows you to select the 11n channel transmission width for this MP between the normal 20MHz or 20/40MHz (channel bonding).

Options are: 11ng20, 11na20, 11na, 11ng, Use Network Setting. 11ng20 selects 2.4GHz band for 11n with 20MHz channel width. 11ng selects 2.4GHz band for 11n with 20/40MHz channel width. 11na20 selects 5GHz band for 11n with 20MHz channel width. 11na selects 5GHz band for 11n with 20/40MHz channel width.


Coverage Channel

This setting allows you to select a different coverage channel to avoid using same or overlapping channel with nearby MPs.

Non-overlapping channels for 2.4GHz band are Channel1, Channel 6 and Channel 11.

To select, click on the channel number, range 1 to 11 or 1 to 13, depending on the country set selected.

When Auto is selected, the channel is automatically selected during the initial power up sequence.

* Note: For Single Radio MeshPoint, there is no Auto selection.


Individual Settings


To customize the settings of an MP, from the CC, open the Mesh Management tab page from the menu.

Click the Edit button for that MP in the MP list table you want to edit.

The Edit MeshPoint page is shown as on the right:

INSTALLER TOOLS


Only Accessible on CloudManager Currently the following services are supported

Changing of MP Check-In IP address Changing of MP Mesh ID

4. PERFORMANCE TEST

Throughput

Performance test

Hop 1Hop 2

Hop 3

Roaming

Performance test

(1) (2)

REDUNDANCY

Performance test

1)

2)

5. SCENARIOS

Installer Tools

Scenarios

hotspot

Pay service access Create voucher creation plans Select Prepaid or Postpaid option to generate voucher Operator can monitor and manage user connection status

Office and Guest access Set up office plan for staff connection requirements/parameters Network admin can create user account name and password for staff access Manager can monitor and manage staff from the Office and Staff list

Scenarios

cameras

Scenarios

Bridge Mode

Fast roaming

Scenarios

Bridge Mode& MeshSpan

Documents

Mesh Training