MEDELSTORGB

ENGLISHPlease refer to the last page of this manual for the full list of IKEAappointed After Sales Service Provider and relative national phonenumbers.

ENGLISH 4

ContentsSafety information 4Safety instructions 6Product description 7Control panel 8Programmes 8Options 10Settings 10Before first use 13

Daily use 15Hints and tips 17Care and cleaning 18Troubleshooting 20Technical information 24Environmental concerns 24IKEA guarantee 25

Subject to change without notice.

Safety information

Before the installation and use of the appliance, carefully readthe supplied instructions. The manufacturer is not responsiblefor any injuries or damage that are the result of incorrectinstallation or usage. Always keep the instructions in a safe andaccessible location for future reference.

Children and vulnerable people safety• This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory ormental capabilities or lack of experience and knowledge ifthey have been given supervision or instruction concerningthe use of the appliance in a safe way and understand thehazards involved.

• Children between 3 and 8 years of age and persons withvery extensive and complex disabilities shall be kept awayfrom the appliance unless continuously supervised.

• Children of less than 3 years of age should be kept awayfrom the appliance unless continuously supervised.

• Do not let children play with the appliance.• Keep detergents away from children.• Keep children and pets away from the appliance when the

door is open.

ENGLISH 4

• Children shall not carry out cleaning and user maintenance ofthe appliance without supervision.

General Safety• This appliance is intended to be used in household and

similar applications such as:– farm houses; staff kitchen areas in shops, offices and other

working environments;– by clients in hotels, motels, bed & breakfast and other

residential type environments.• Do not change the specification of this appliance.• The operating water pressure (minimum and maximum) must

be between 0.5 (0.05) / 8 (0.8) bar (MPa)• Follow the maximum number of 9 place settings.• If the supply cord is damaged, it must be replaced by the

manufacturer, its Authorised Service Centre or similarlyqualified persons in order to avoid a hazard.

• Put the cutlery in the cutlery basket with the sharp endspointing down or put them in the cutlery drawer in ahorizontal position with the sharp edges down.

• Do not leave the appliance with the open door unattended toavoid stepping accidentally onto it.

• Before any maintenance operation, deactivate the applianceand disconnect the mains plug from the socket.

• Do not use high pressure water sprays and/or steam to cleanthe appliance.

• If the appliance has ventilation openings in the base, theymust not be covered e.g. by a carpet.

• The appliance is to be connected to the water mains usingthe new supplied hose-sets. Old hose sets must not bereused.

ENGLISH 5

Safety instructions

Installation

Warning! Only a qualifiedperson must install thisappliance.

• Remove all the packaging.• Do not install or use a damaged

appliance.• Do not use the appliance before

installing it in the built-in structure due tosafety manner.

• Follow the installation instructionssupplied with the appliance.

• Always take care when moving theappliance as it is heavy. Always usesafety gloves and enclosed footwear.

• Do not install or use the appliance wherethe temperature is less than 0 °C.

• Install the appliance in a safe andsuitable place that meets installationrequirements.

Electrical connection

Warning! Risk of fire and electricshock.

• The appliance must be earthed.• Make sure that the parameters on the

rating plate are compatible with theelectrical ratings of the mains powersupply.

• Always use a correctly installedshockproof socket.

• Do not use multi-plug adapters andextension cables.

• Make sure not to cause damage to themains plug and to the mains cable.Should the mains cable need to bereplaced, this must be carried out by ourAuthorised Service Centre.

• Connect the mains plug to the mainssocket only at the end of the installation.Make sure that there is access to themains plug after the installation.

• Do not pull the mains cable to disconnectthe appliance. Always pull the mainsplug.

• This appliance complies with the E.E.C.Directives.

• This appliance is fitted with a 13 A mainsplug. If it is necessary to change themains plug fuse, use only a 13 A ASTA(BS 1362) fuse (UK and Ireland only).

Water connection• Do not cause damage to the water

hoses.• Before connection to new pipes, pipes

not used for a long time, where repairwork has been carried out or newdevices fitted (water meters, etc.), let thewater flow until it is clean and clear.

• Ensure that there are no visible waterleaks during and after the first use of theappliance.

• The water inlet hose has a safety valveand a sheath with an inner mains cable.

Warning! Dangerous voltage.• If the water inlet hose is damaged,

immediately close the water tap anddisconnect the mains plug from the mainssocket. Contact the Authorised ServiceCentre to replace the water inlet hose.

Use• Do not put flammable products or items

that are wet with flammable products in,near or on the appliance.

ENGLISH 6

• Dishwasher detergents are dangerous.Follow the safety instructions on thedetergent packaging.

• Do not drink and play with the water inthe appliance.

• Do not remove the dishes from theappliance until the programme iscomplete. Some detergent may remainon the dishes.

• Do not sit or stand on the open door ofthe appliance.

• The appliance can release hot steam ifyou open the door while a programmeoperates.

Service• To repair the appliance contact the

Authorised Service Centre.

• Use original spare parts only.

Disposal

Warning! Risk of injury orsuffocation.

• Disconnect the appliance from the mainssupply.

• Cut off the mains cable and discard it.• Remove the door catch to prevent

children and pets to get closed in theappliance.

Product description

8

7

6

5

4

1

3

2

1 Lower spray arm2 Filters3 Rating plate4 Rinse aid dispenser5 Detergent dispenser6 Salt container7 Upper spray arm8 Upper basket

Beam-on-FloorBeam-on-Floor is a light that is displayedon the floor below the appliance door.• When a programme starts, a white light

is on and stays on for the duration of theprogramme.

• When the programme is completed, thewhite light is off.

• When the appliance has a malfunction,the white light flashes.

Beam-on-Floor is off when theappliance is deactivated.

ENGLISH 7

When AutoOpen is activatedduring the drying phase, theprojection on the floor may notbe completely visible. To see ifthe cycle has ended, check thecontrol panel.

Control panel

1 2 93 4 5 6 7 8

1 On/off button2 Display3 Delay button4 Programme button (up)5 Programme button (down)

6 ExtraHygiene button7 DryPlus button8 RESET button9 Indicators

Indicators

Indicator DescriptionRinse aid indicator. It is always off while the programme operates.

Salt indicator. It is always off while the programme operates.

Programmes

Programme Degree of soilType of load

Programme pha-ses

Consumption values1)

Duration(min)

Energy(kWh)

Water(l)

P1 2)

45 °C - 70 °C

AllCrockery, cut-lery, pots andpans

• Prewash• Wash from 45

°C to 70 °C• Rinses• Dry

45 - 151 0.6 - 1.2 6 - 11

ENGLISH 8

Programme Degree of soilType of load

Programme pha-ses

Consumption values1)

Duration(min)

Energy(kWh)

Water(l)

P2 3)

70 °C

Heavy soilCrockery, cut-lery, pots andpans

• Prewash• Wash 70 °C• Rinses• Dry

160 - 168 1.1 - 1.3 13 - 14

P3 4)

60 °C or 65 °C

Fresh soilCrockery andcutlery

• Wash 60 °C or65 °C

• Rinses

38 0.7 8

P4 5)

50 °C

Normal soilCrockery andcutlery

• Prewash• Wash 50 °C• Rinses• Dry

227 0.777 9.9

P5

45 °C

Normal or lightsoilDelicate crock-ery and glass-ware

• Wash 45 °C• Rinses• Dry

75 - 85 0.8 - 0.9 11 - 12

P6 6)

All • Prewash 14 0.1 4

1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity ofdishes can change the values.2) The appliance senses the degree of soil and the quantity of items in the baskets, it automatically adjusts the tem-perature and the quantity of the water, the energy consumption and the programme duration.3) This programme is indicated for heavy soil loading to get the sufficient cleaning results on pots and pans.4) With this programme you can wash a load with fresh soil. It gives good washing results in a short time.5) With this programme you have the most efficient use of water and energy consumption for crockery and cutlery withnormal soil. (This is the standard programme for test institutes).6) Use this programme to quickly rinse the dishes. this prevents the remaining food to bond on the dishes and badodours to come out from the appliance. Do not use detergent with this programme.

Information for test institutesTo receive the necessary information forconducting performance tests (e.g.according to EN60436), send an email to:info.test@dishwasher-production.comIn your request please include the productnumber code (PNC) found on the ratingplate.

For any other questions regarding yourdishwasher please refer to the service bookprovided with your appliance.

ENGLISH 9

Options

Desired options must beactivated every time before youstart a programme.It is not possible to activate ordeactivate options while aprogramme is running.

Not all options are compatiblewith each other. If you select noncompatible options, theappliance automaticallydeactivates one or more of them.Only the indicators of the stillactive options are on.

If an option is not applicable to aprogramme, the related indicatoris off or it flashes quickly for afew seconds and then goes out.

Activating options can affect thewater and energy consumptionas well as the programmeduration.

ExtraHygieneThis option provides better hygiene resultsby keeping the temperature at 70 °C for atleast 10 minutes during the last rinsingphase.

How to activate ExtraHygiene

Press .

The related indicator is on.The display shows the updated programmeduration.The ExtraHygiene option is not applicableto the following programmes:

• P5 (Glass)• P6 (Rinse & Hold)

AutoOpen is deactivated whenthe programme P3 (Quick) iscombined with ExtraHygieneoption due to the hightemperature.

DryPlusActivate this option to boost the dryingperformance.The combination of DryPlus and rinse aidensures even better drying results.DryPlus is a permanent option for allprogrammes other than P4 (ECO). It isautomatically activated in next cycles. Thisconfiguration can be changed at any time.

Every time P4 (ECO) is activated,DryPlus is off and needs to bechosen manually.

How to activate DryPlus

Press .The related indicator is on.The display shows the updated programmeduration.

Settings

Programme selection mode and usermodeWhen the appliance is in programmeselection mode it is possible to set aprogramme and to enter the user mode.

Settings available in the user mode:• The level of water softener according to

the water hardness.• Activation or deactivation of the acoustic

signal for the end of a programme.

ENGLISH 10

• Activation or deactivation of the rinseaid empty notification.

• Activation or deactivation of AutoOpen.As the appliance stores the savedsettings, there is no need to configure itbefore every cycle.

How to set the programme selection modeThe appliance is in programme selectionmode when, after the activation, the displayshows the number of programme .The display shows the programme durationafter a few seconds.After activation, the appliance is inprogramme selection mode by default. Ifnot, set the programme selection mode thefollowing way:1. Press and hold RESET until the

appliance is in programme selectionmode.

The water softenerThe water softener removes minerals fromthe water supply, which would have anegative effect on the washing results andon the appliance.The higher the content of these minerals, theharder your water is. Water hardness ismeasured in equivalent scales.The water softener should be adjustedaccording to the hardness of the water inyour area. Your local water authority canadvise you on the hardness of the water inyour area. It is important to set the rightlevel of the water softener to assure goodwashing results.

Water hardnessGerman degrees

(°dH)French degrees

(°fH)mmol/l Clarke de-

greesWater softener level

47 - 50 84 - 90 8.4 - 9.0 58 - 63 10

43 - 46 76 - 83 7.6 - 8.3 53 - 57 9

37 - 42 65 - 75 6.5 - 7.5 46 - 52 8

29 - 36 51 - 64 5.1 - 6.4 36 - 45 7

23 - 28 40 - 50 4.0 - 5.0 28 - 35 6

19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1)

15 - 18 26 - 32 2.6 - 3.2 18 - 22 4

11 - 14 19 - 25 1.9 - 2.5 13 - 17 3

4 - 10 7 - 18 0.7 - 1.8 5 - 12 2

<4 <7 <0.7 < 5 1 2)

1) Factory setting.2) Do not use salt at this level.

ENGLISH 11

Regardless of the type of detergent used,set the proper water hardness level tokeep the salt refill indicator active.

Multi-tabs containing salt are noteffective enough to soften hardwater.

How to set the water softener levelThe appliance must be in programmeselection mode.1. To enter the user mode, press and hold

simultaneously and untilthe indicators , , and flash and the display is blank.

2. Press .• The indicators , and

are off.• The indicator still flashes.• The display shows the current setting:

e.g. = level 5.3. Press repeatedly to change the

setting.4. Press the on/off button to confirm the

setting.

The rinse aid empty notificationThe rinse aid helps to dry the dishes withoutstreaks and stains.The rinse aid is automatically releasedduring the hot rinse phase.When rinse aid chamber is empty, the rinseaid indicator is turned on notifying to refillrinse aid. If the drying results aresatisfactory while using multi-tablets only, itis possible to deactivate the notification forrefilling rinse aid. However, for best dryingperformance, always use rinse aid.If standard detergent or multi-tabletswithout rinse aid are used, activate thenotification to keep the rinse aid refillindicator active.

How to deactivate the rinse aid emptynotificationThe appliance must be in programmeselection mode.1. To enter the user mode, press and hold

simultaneously and untilthe indicators , , and start flashing and the display is blank.

2. Press .• The indicators , and are

off.• The indicator still flashes.• The display shows the current setting.

– = rinse aid empty notificationactivated.

– = rinse aid emptynotification deactivated.

3. Press to change the setting.4. Press on/off to confirm the setting.

Acoustic signalsAcoustic signals sound when a malfunctionof the appliance occurs. It is not possible todeactivate these acoustic signals.There is also an acoustic signal that soundswhen the programme is complete. Thisacoustic signal is activated by default andyou can deactivate it.When you press the main switch to turn onthe dishwasher, it makes a short beepsound. The beep is activated by default andyou can deactivate it along with theacoustic signal for the end of a programme.In addition, an acoustic signal soundsbefore the AutoOpen opens the door. Thisacoustic signal stops only if AutoOpen isdeactivated.

ENGLISH 12

How to deactivate the acoustic signalsThe appliance must be in programmeselection mode.1. To enter the user mode, press and hold

simultaneously and untilthe indicators , , and flash and the display is blank.

2. Press .• The indicators , and are

off.• The indicator still flashes.• The display shows the current setting:

– = Acoustic signal off.– = Acoustic signal on.

3. Press to change the setting.4. Press on/off to confirm the setting.

AutoOpenAutoOpen improves the drying results withless energy consumption.

During the drying phase, thedoor opens automatically andremains ajar.

Caution! Do not try to close theappliance door within 2 minutesafter automatic opening. This cancause damage to the appliance.

AutoOpen is automatically activated withall programmes excluding .To improve the drying performance refer tothe DryPlus option or activate AutoOpen.

To avoid possible hazards insidethe appliance (such as knives,sharp objects or chemicals) forchildren, pets or people withdisabilities deactivate thefunction.

How to deactivate AutoOpenThe appliance must be in programmeselection mode.1. To enter the user mode, press and hold

simultaneously and untilthe indicators , , and start flashing and the display is blank.

2. Press .• The indicators , and

are off.• The indicator still flashes.• The display shows the current setting:

= AutoOpen activated.3. Press to change the setting: =

AutoOpen deactivated.4. Press on/off to confirm the setting.

Before first use

1. Make sure that the current level of thewater softener agrees with the

hardness of the water supply. If not,adjust the level of the water softener.

2. Fill the salt container.

ENGLISH 13

3. Fill the rinse aid dispenser.4. Open the water tap.5. Start a programme to remove any

processing residuals that can still beinside the appliance. Do not usedetergent and do not load the baskets.

After starting a programme, itmay take up to 5 minutes for theappliance to recharge the resinin the water softener. It seemsthat the appliance is not working.The washing phase starts onlyafter this procedure is completed.The procedure is repeatedperiodically.

The salt container

Caution! Use rough saltdesigned for dishwashers only.Fine salt increases the risk ofcorrosion.

The salt is used to recharge the resin in thewater softener and to assure good washingresults in daily use.

Filling the salt container

1 2

3

Put 1 litre of waterin the salt container(only for the firsttime).

4

Put 1 kg of salt inthe salt container.

5

Turn the cap of thesalt containerclockwise to closethe salt container.

Caution! Water and salt maycome out of the salt containerwhen you fill it. After you fill thesalt container, immediately starta programme to preventcorrosion.

ENGLISH 14

Filling the rinse aid dispenser

1 2

3

max

4

5

M A X

+

4 3 2 1 -

To adjust thereleased quantity ofrinse aid, turn theselector betweenthe position 1 (thelowest quantity) andthe position 4 (thehighest quantity).Refer to "TROUBLESHOOTING".

Daily use

1. Open the water tap.2. Press the on/off button to activate the

appliance.Make sure that the appliance is inprogramme selection mode.

• If the salt indicator is on, fill the saltcontainer.

• If the rinse aid indicator is on, fill therinse aid dispenser.

3. Load the baskets.4. Add the detergent.5. Set and start the correct programme for

the type of load and the degree of soil.

Using the detergent

1 2

3

A

4

ENGLISH 15

5

If the programmehas a prewashphase, put a smallquantity ofdetergent on theinner part of theappliance door.

While using multi-tablets, which contain saltand rinse aid, it is not necessary to fill thesalt container or the rinse aid dispenser.• Adjust the water softener to the lowest

level.• Set the rinse aid dispenser to the lowest

position.

Setting and starting a programme

The Auto Off functionThis function decreases energy consumptionby automatically deactivating theappliance when it is not operating.The function comes into operation:• 5 minutes after the completion of the

programme.• After 5 minutes if the programme has not

started.

Starting a programme1. Keep the appliance door ajar.2. Press the on/off button to activate the

appliance. Make sure that theappliance is in programme selectionmode.

3. Press repeatedly or untilthe display shows the number of thechosen programme. The display showsthe programme number forapproximately 3 seconds and thenshows the programme duration.

4. Set the applicable options.5. Close the appliance door to start the

programme.

Starting a programme with delay start1. Set a programme.2. Press repeatedly until the display

shows the delay time you want to set(from 1 to 24 hours).

The delay indicator comes on.3. Close the appliance door to start the

countdown.While a countdown is running it is possibleto increase the delay time but not to changethe selection of the programme andoptions.When the countdown is completed, theprogramme starts.

Opening the door while the applianceoperatesOpening the door while a programme isrunning stops the appliance. It may affectthe energy consumption and theprogramme duration. After closing the door,the appliance continues from the point ofinterruption.

If the door is opened for morethan 30 seconds during thedrying phase, the runningprogramme ends. It does nothappen if the door is opened byAutoOpen function.

ENGLISH 16

Do not try to close the appliancedoor within 2 minutes afterAutoOpen automatically opensit, as this may cause damage tothe appliance.If, afterwards, the door is closedfor another 3 minutes, therunning programme ends.

Cancelling the delay start while thecountdown operatesWhen you cancel the delay start you haveto set the programme and options again.Press and hold RESET until the appliance isin programme selection mode.

Cancelling the programmePress and hold RESET until the appliance isin programme selection mode.Make sure that there is detergent in thedetergent dispenser before you start a newprogramme.

End of the programmeWhen the programme is completed thedisplay shows 0:00 .1. Press the on/off button or wait for the

Auto Off function to automaticallydeactivate the appliance.

2. Close the water tap.

Hints and tips

GeneralFollow the hints below to ensure optimalcleaning and drying results in daily use andto help you protect the environment.• Remove larger residues of food from the

dishes into the waste bin.• Do not pre-rinse dishes by hand. When

needed, select a programme with aprewash phase.

• Always use the whole space of thebaskets.

• Make sure that items in the baskets donot touch or cover each other. Only thencan the water completely reach andwash the dishes.

• You can use dishwasher detergent, rinseaid and salt separately or you can usethe multi-tablets (e.g. ''All in 1''). Followthe instructions on the packaging.

• Select a programme according to thetype of load and the degree of soil.

offers the most efficient use ofwater and energy consumption.

Using salt, rinse aid and detergent• Only use salt, rinse aid and detergent for

dishwasher. Other products can causedamage to the appliance.

• The rinse aid helps, during the lastrinsing phase, to dry the dishes withoutstreaks and stains.

• Multi-tablets are usually suitable inareas with a water hardness up to 21°dH. In areas exceeding this limit, rinseaid and salt must be used in addition tothe multi-tablets. However, in areas withhard and very hard water werecommend to use solo-detergent(powder, gel, tablets without additionalfunctions), rinse aid and salt separatelyfor optimal cleaning and drying results.

• Detergent tablets do not fully dissolvewith short programmes. To preventdetergent residues on the tableware, werecommend that you use the tablets withlong programmes.

• Do not use more than the correctquantity of detergent. Refer to theinstructions on the detergent packaging.

ENGLISH 17

What to do if you want to stop using multi-tabletsBefore you start to use separatelydetergent, salt and rinse aid do thefollowing procedure.1. Set the highest level of the water

softener.2. Make sure that the salt and rinse aid

containers are full.3. Start the shortest programme with a

rinsing phase. Do not add detergentand do not load the baskets.

4. When the programme is completed,adjust the water softener according tothe water hardness in your area.

5. Adjust the released quantity of rinse aid.6. Activate the rinse aid empty notification.

Loading the baskets

Refer to the supplied leaflet withexamples of the load of thebaskets.

• Only use the appliance to wash itemsthat are dishwasher-safe.

• Do not put in the appliance items madeof wood, horn, aluminium, pewter andcopper.

• Do not put in the appliance items thatcan absorb water (sponges, householdcloths).

• Remove remaining food from the items.• Soak items with remaining burned food

in water.• Put hollow items (cups, glasses and pans)

with the opening down.

• Make sure that cutlery and dishes do notbond together. Mix spoons with othercutlery.

• Make sure that glasses do not touchother glasses.

• Put small items in the cutlery basket.• Put light items in the upper basket. Make

sure that the items do not move.• Make sure that the spray arm can move

freely before you start a programme.

Before starting a programmeBefore you start the selected programme,make sure that:• The filters are clean and correctly

installed.• The cap of the salt container is tight.• The spray arms are not clogged.• There is enough salt and rinse aid (unless

you use multi-tablets).• The arrangement of the items in the

baskets is correct.• The programme is suitable to the type of

load and the degree of soil.• The correct quantity of detergent is used.

Unloading the baskets1. Let the tableware cool down before you

remove it from the appliance. Hot itemscan be easily damaged.

2. First remove items from the lowerbasket, then from the upper basket.

After the programme iscompleted, water can still remainon the inside surfaces of theappliance.

Care and cleaning

Warning! Before maintenance,deactivate the appliance anddisconnect the mains plug fromthe main socket.

Dirty filters and clogged sprayarms decrease the washingresults. Make a check regularlyand, if necessary, clean them.

ENGLISH 18

Cleaning the filters

1

Make sure thatthere are noresidues of food orsoil in or around theedge of the sump.

2

C

B

A

The filter system ismade of three parts.

3

To remove filters (B)and (C), turn thehandlecounterclockwiseand pull it upwards.Remove the filter (C)out of filter (B).Wash the filters withwater.

4

Remove the flatfilter (A). Wash thefilter with water.

5D

Put the flat filter (A)back in place. Makesure that it iscorrectly positionedunder the 2 guides(D).

6

Reassemble thefilters (B) and (C).Put them back in thefilter (A). Turn thehandle clockwiseuntil it locks.

An incorrect position of the filterscan cause bad washing resultsand damage to the appliance

Cleaning the filter of the inlet hose

1

Close the water tap.

2

A

Disconnect the hose.Turn the fastener Aclockwise.

3

Clean the filter ofthe inlet hose.

4

ENGLISH 19

Cleaning the spray armsDo not remove the spray arms. If the holesin the spray arms are clogged, removeremaining parts of soil with a thin pointedobject.

External cleaning• Clean the appliance with a moist soft

cloth.• Only use neutral detergents.• Do not use abrasive products, abrasive

cleaning pads or solvents.

Internal cleaning• Carefully clean the appliance, including

the rubber gasket of the door, with a softdamp cloth.

• If you regularly use short durationprogrammes, these can leave deposits ofgrease and limescale inside theappliance. To prevent this, werecommend to run long durationprogrammes at least 2 times per month.

• To maintain the performance of yourappliance at its best, we recommend touse monthly a specific cleaning productfor dishwashers. Follow carefully theinstructions on the packaging of theproduct.

Troubleshooting

If the appliance does not start or it stopsduring operation, first check if you can solvethe problem by yourself with the help of theinformation in the table or contact anAuthorised Service Centre.

Warning! Repairs not properlydone may result in serious risk tothe safety of the user. Anyrepairs must be performed byqualified personnel.

With some problems, the display showsan alarm code.The majority of problems that can occurcan be solved without the need to contactan Authorised Service Centre.

Problem and alarm code Possible cause and solutionYou cannot activate the ap-pliance.

• Make sure that the mains plug is connected to the mainssocket.

• Make sure that there is no damaged fuse in the fuse box.

The program does not start. • Make sure that the appliance door is closed.• If the delay start is set, cancel the setting or wait for the

end of the countdown.• The appliance has started the procedure to recharge the

resin inside the water softener. The duration of the pro-cedure is approximately 5 minutes.

ENGLISH 20

Problem and alarm code Possible cause and solutionThe appliance does not fillwith water.The display shows or

.

• Make sure that the water tap is open.• Make sure that the pressure of the water supply is not

too low. For this information, contact your local waterauthority.

• Make sure that the water tap is not clogged.• Make sure that the filter in the inlet hose is not clogged.• Make sure that the inlet hose has no kinks or bends.

The appliance does notdrain the water.The display shows .

• Make sure that the sink spigot is not clogged.• Make sure that the filter in the outlet hose is not clogged.• Make sure that the interior filter system is not clogged.• Make sure that the drain hose has no kinks or bends.

The anti-flood device is on.The display shows .

• Close the water tap and contact an Authorised ServiceCentre.

The appliance stops andstarts more times during op-eration.

• It is normal. It provides optimal cleaning results and en-ergy savings.

The program lasts too long. • If the delayed start option is set, cancel the delay settingor wait for the end of the countdown.

The remaining time in thedisplay increases and skipsnearly to the end of pro-gram time.

• This is not a defect. The appliance is working correctly.

Small leak from the appli-ance door.

• The appliance is not levelled. Loosen or tighten the ad-justable feet (if applicable).

• The appliance door is not centred on the tub. Adjust therear foot (if applicable).

The appliance door is diffi-cult to close.

• The appliance is not levelled. Loosen or tighten the ad-justable feet (if applicable).

• Parts of the tableware are protruding from the baskets.

Rattling/knocking soundsfrom inside the appliance.

• The tableware is not properly arranged in the baskets.Refer to basket loading leaflet.

• Make sure that the spray arms can rotate freely.

The appliance trips the cir-cuit-beaker.

• The amperage is insufficient to supply simultaneously allthe appliances in use. Check the socket amperage andthe capacity of the meter or turn off one of the applian-ces in use.

• Internal electrical fault of the appliance. Contact an Au-thorised Service Centre.

ENGLISH 21

Problem and alarm code Possible cause and solutionThe salt indicator continuesto stay on after the replen-ishment of the salt container

• If after 3 or 4 programmes, the salt indicator continues tostay on, contact an Authorised Service Centre.This can occur when you are using salt that needs moretime to dissolve.There is no unwanted effect on the performance of theappliance.

Refer to "Before first use", "Daily use", or "Hints and tips"for other possible causes.

Once you have checked the appliance,deactivate and activate the appliance. If

the problem occurs again, contact anAuthorised Service Centre.For alarm codes not described in the table,contact an Authorised Service Centre.

The washing and drying results are not satisfactory

Problem Possible cause and solutionPoor washing results. • Refer to "Daily use", "Hints and tips" and basket

loading leaflet.• Use more intensive washing programmes.• Clean spray arm jets and filter. Refer to "Care and

Cleaning".

Poor drying results. • Tableware has been left for too long inside a closedappliance.

• There is no rinse aid or the dosage of rinse aid is notenough. Set the rinse aid dispenser to a higher level.

• Plastic items may need to be towel dried.• For the best drying performance activate the option

DryPlus and set AutoOpen.• We recommend to always use rinse aid, even in com-

bination with multi-tablets.

There are whitish streaks orbluish layers on glasses anddishes.

• The release quantity of rinse aid is too much. Adjustthe rinse aid level to a lower level.

• The quantity of detergent is too much.

There are stains and dry wa-ter drops on glasses anddishes.

• The released quantity of rinse aid is not sufficient. Ad-just the rinse aid level to a higher level.

• The quality of the rinse aid can be the cause.

ENGLISH 22

Problem Possible cause and solutionThe dishes are wet. • For the best drying performance activate the option

DryPlus and set AutoOpen .• The programme does not have a drying phase or has

a drying phase with low temperature.• The rinse aid dispenser is empty.• The quality of the rinse aid can be the cause.• The quality of the multi-tablets can be the cause. Try a

different brand or activate the rinse aid dispenser anduse rinse aid and multi-tablets together.

The interior of the appliance iswet.

• This is not a defect of the appliance. it is caused by thehumidity in the air that condenses on the walls.

Unusual foam during washing. • Use the detergent for dishwashers only.• There is a leak in the rinse aid dispenser. Contact an

Authorised Service Centre.

Traces of rust on cutlery. • There is too much salt in the water used for washing.Refer to "The water softener".

• Silver and stainless steel cutlery were placed together.Avoid to put silver and stainless steel items close to-gether.

There are residues of deter-gent in the dispenser at theend of the programme.

• The detergent tablet got stuck in the dispenser andtherefore was not completely washed away by water.

• Water cannot wash away the detergent from the dis-penser. Make sure that the spray arm is not blocked orclogged.

• Make sure that items in the baskets do not impede thelid of the detergent dispenser from opening.

Odours inside the appliance. • Refer to "Internal cleaning".

Limescale deposits on the ta-bleware, on the tub and onthe inside of the door.

• The level of salt is low, check the refill indicator.• The cap of the salt container is loose.• Your tap water is hard. Refer to "The water softener".• Even using multi-functional tabs use salt and set regen-

eration of the water softener. Refer to "The watersoftener".

• If lime scale deposits still remain, clean the appliancewith appliance cleaners which are particularly suitablefor this purpose.

• Try different detergent.• Contact the detergent manufacturer.

ENGLISH 23

Problem Possible cause and solutionDull, discoloured or chippedtableware.

• Make sure that only dishwasher-safe items are wash-ed in the appliance.

• Load and unload the basket carefully. Refer to basketloading leaflet.

• Place delicate items in the upper basket.

Refer to "Before first use", "Daily use" or "Hints and tips"for other possible causes.

Technical information

Product denomination Fully integrated dishwasher

Dimensions Width / height / depth(mm)

446 / 818 - 898 / 550

Electrical connection 1) Voltage (V) 220 - 240

Frequency (Hz) 50

Water supply pressure Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8)

Water supply Cold water or hot water 2) max 60 °C

Capacity Place settings 9

Power consumption Left-on mode (W) 5.0

Power consumption Off-mode (W) 0.501) Refer to the rating plate for other values.2) If the hot water comes from alternative source of energy, (e.g. solar panels, aeolian energy), use the hot water sup-ply to decrease energy consumption.

Environmental concerns

Recycle materials with the symbol . Putthe packaging in relevant containers torecycle it. Help protect the environment andhuman health by recycling waste ofelectrical and electronic appliances. Do not

dispose of appliances marked with thesymbol with the household waste. Returnthe product to your local recycling facility orcontact your municipal office.

ENGLISH 24

IKEA guarantee

How long is the IKEA guarantee valid?This guarantee is valid for 5 years from theoriginal date of purchase of Your applianceat IKEA. The original sales receipt isrequired as proof of purchase. If servicework is carried out under guarantee, thiswill not extend the guarantee period for theappliance.Who will execute the service?IKEA service provider will provide theservice through its own service operationsor authorized service partner network.What does this guarantee cover?The guarantee covers faults of theappliance, which have been caused byfaulty construction or material faults fromthe date of purchase from IKEA. Thisguarantee applies to domestic use only. Theexceptions are specified under the headline“What is not covered under thisguarantee?” Within the guarantee period,the costs to remedy the fault e.g. repairs,parts, labour and travel will be covered,provided that the appliance is accessiblefor repair without special expenditure. Onthese conditions the EU guidelines (Nr.99/44/EG) and the respective localregulations are applicable. Replaced partsbecome the property of IKEA.What will IKEA do to correct the problem?IKEA appointed service provider willexamine the product and decide, at its solediscretion, if it is covered under thisguarantee. If considered covered, IKEAservice provider or its authorized servicepartner through its own service operations,will then, at its sole discretion, either repairthe defective product or replace it with thesame or a comparable product.

What is not covered under thisguarantee?• Normal wear and tear.• Deliberate or negligent damage,

damage caused by failure to observeoperating instructions, incorrectinstallation or by connection to thewrong voltage, damage caused bychemical or electro-chemical reaction,rust, corrosion or water damageincluding but not limited to damagecaused by excessive lime in the watersupply, damage caused by abnormalenvironmental conditions.

• Consumable parts including batteriesand lamps.

• Non-functional and decorative partswhich do not affect normal use of theappliance, including any scratches andpossible color differences.

• Accidental damage caused by foreignobjects or substances and cleaning orunblocking of filters, drainage systems orsoap drawers.

• Damage to the following parts: ceramicglass, accessories, crockery and cutlerybaskets, feed and drainage pipes, seals,lamps and lamp covers, screens, knobs,casings and parts of casings. Unless suchdamages can be proved to have beencaused by production faults.

• Cases where no fault could be foundduring a technician’s visit.

• Repairs not carried out by our appointedservice providers and/or an authorizedservice contractual partner or wherenon-original parts have been used.

• Repairs caused by installation which isfaulty or not according to specification.

• The use of the appliance in a non-domestic environment i.e. professionaluse.

• Transportation damages. If a customertransports the product to their home orother address, IKEA is not liable for any

ENGLISH 25

damage that may occur during transport.However, if IKEA delivers the product tothe customer's delivery address, thendamage to the product that occursduring this delivery will be covered bythis guarantee.

• Cost for carrying out the initialinstallation of the IKEA appliance.However, if an IKEA service provider orits authorized service partner repairs orreplaces the appliance under the termsof this guarantee, the service provider orits authorized service partner will re-install the repaired appliance or installthe replacement, if necessary.

This restriction do not apply to fault-freework carried out by a qualified specialistusing our original parts in order to adaptthe appliance to the technical safetyspecifications of another EU country.How country law appliesThe IKEA guarantee gives You specific legalrights, which covers or exceed localdemands. However these conditions do notlimit in any way consumer rights describedin the local legislation.Area of validityFor appliances which are purchased in oneEU country and taken to another EUcountry, the services will be provided in theframework of the guarantee conditionsnormal in the new country. An obligation tocarry out services in the framework of theguarantee exists only if the appliancecomplies and is installed in accordancewith:• the technical specifications of the country

in which the guarantee claim is made;• the Assembly Instructions and User

Manual Safety Information;The dedicated After Sales Service forIKEA appliances:

Please do not hesitate to contact IKEA AfterSales Service to:1. make a service request under this

guarantee;2. ask for clarification on installation of the

IKEA appliance in the dedicated IKEAkitchen furniture. The service won’tprovide clarifications related to:• the overall IKEA kitchen installation;• connections to electricity (if machine

comes without plug and cable), towater and to gas since they have tobe executed by an authorizedservice engineer.

3. ask for clarification on user manualcontents and specifications of the IKEAappliance.

To ensure that we provide you with the bestassistance, please read carefully theAssembly Instructions and/or the UserManual section of this booklet beforecontacting us.How to reach us if You need our service

Please refer to the last page of this manualfor the full list of IKEA appointed contactsand relative national phone numbers.

ENGLISH 26

In order to provide You with aquicker service, we recommendthat You use the specific phonenumbers listed at the end of thismanual. Always refer to thenumbers listed in the booklet ofthe specific appliance You needan assistance for. Before callingus, assure that You have to handthe IKEA article number (8 digitcode) and the Serial Number (8digit code that can be found onthe rating plate) for theappliance of which you need ourassistance.

SAVE THE SALES RECEIPT! It isYour proof of purchase andrequired for the guarantee toapply. Note that the receiptreports also the IKEA articlename and number (8 digit code)for each of the appliances youhave purchased.

Do You need extra help?For any additional questions not related toAfter Sales of your appliances, pleasecontact our nearest IKEA store call centre.We recommend you read the appliancedocumentation carefully before contactingus.

ENGLISH 27

28

emit gninepOeeF llaCrebmun enohPyrtnuoC

België 070 246016

Binnenlandse gesprekskosten 8 tot 20 Weekdagen

eniames nE .02 à 8 xuanoitan sleppa sed firaT euqigleB

България 00359888164080 0035924274080 Такса за повикване от страната От 9 до 18 ч в работни дни

Česká republika 246 019721 Cena za místní hovor 8 až 20 v pracovních dnech

Danmark 70 15 09 09 Landstakst man. - fre. 09.00 - 20.00lør. - søn. 09.00 - 18.00

Deutschland +49 1806 33 45 32* * 0,20 €/Verbindung aus dem

Festnetz max. 0,60 €/Verbindung aus dem Mobilfunknetz

Werktags von 8.00 bis 20.00

Ελλάδα 211 176 8276 Υπεραστική κλήση 8 έως 20 κατά τις εργάσιμες ημέρες

España 91 1875537 Tarifa de llamadas nacionales De 8 a 20 en días laborables

France 0170 36 02 05 Tarif des appels nationaux 9 à 21. En semaine

Hrvatska 00385 1 6323 339 Trošak poziva 27 lipa po minuti radnim danom od ponedjeljka do petka od 08:00 do 16:00

Ireland 0 14845915 National call rate 8 till 20 Weekdays

Ísland 5880503 Innanlandsgjald fyrir síma 9 til 18. Virka daga

Italia 02 00620818 Tariffa applicataalle chiamate nazionali dalle 8 alle 20 nei giorni feriali

Κυπρος 22 030 529 Υπεραστική κλήση 8 έως 20 κατά τις εργάσιμες ημέρες

Lietuva 5 230 06 99 Nacionalinių pokalbių tarifai Pr. - Ketv.: 8:00 - 12:00, 12:45 - 17:00 Pnkt.: 8:00 - 12:00, 12:45 - 15:45

Magyarország 061 998 0549 Belföldi díjszabás Hétköznap 8 és 10 óra között

NederlandLuxembourg

0900 - 235 45 32 (0900-BEL IKEA)

0031 - 50 316 8772 (internationaal)

Geen extra kosten. Alleen lokaal tarief.

ma-vr: 8.00 - 21.00zat: 9.00 - 21.00

zon / pub. vakantie: 10.00 - 18.00

Norge 22 72 35 00 Takst innland 8 til 20 ukedager

Österreich +43-1-2056356 max. 10 Cent/min. Mo - Fr 8.00 - 20.00 Uhr

Polska 801 400 711 Stawka wg taryfy krajowej Od 8 do 20 w dni robocze

Portugal 211557985 Chamada Nacional 9 às 21. Dias de Semana*excepto feriados

România 021 211 08 88 Tarif apel naţional 8 - 20 în zilele lucrătoare

Россия 8 495 6662929 Действующие телефонные тарифы

с 8 до 20 по рабочим днямВремя московское

Schweiz

031 5500 324

Tarif für Anrufe im Bundesgebiet 8 bis 20 Werktage

eniames nE .02 à 8 xuanoitan sleppa sed firaT essiuS

Svizzera Tariffa applicataalle chiamate nazionali dalle 8 alle 20 nei giorni feriali

Slovensko (02) 3300 2554 Cena vnútroštátneho hovoru 8 až 20 v pracovných dňoch

Suomi 030 6005203Lankapuhelinverkosta

0,0835 €/puhelu + 0,032 €/minMatkapuhelinverkosta 0,192 €/min

arkipäivisin 8.00 - 20.00

Sverige 0775 700 500 lokalsamtal (lokal taxa) mån-fre 8.30 - 20.00lör-sön 9.30 - 18.00

Україна 044 586 2078 Міжміськи дзвінки платні 9 - 21 В робочі дні United Kingdom 020 3347 0044 National call rate 9 till 21. Weekdays

Србија+381 11 7 555 444

(ако позивате изван Србије)011 7 555 444

(ако позивате из Србије)

Цена позива у националном саобраћају

Понедељак – субота: 09 – 20 Недеља: 09 – 18

moc.aeki.wwwajinevolS ,ajivtaL ,itseE

*

29

30

31

1569

1383

2-A-

1120

19

© Inter IKEA Systems B.V. 2019 21552 AA-2003845-2