(A2LA Cert. No. 0078.02) Revised 04/23/2018 Page 1 of 11

SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005

INTERTEK TESTING SERVICES NA, INC. 4700 Broadmoor SE, Suite 200

Kentwood, MI 49512 Authorized Representative: Paul D. Coghill

Phone: 440-289-5841 Local Representative: Karen Scofield

Phone: 616-656-7401

MECHANICAL 1, 2

Valid To: December 31, 2018 Certificate Number: 0078.02 In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following tests: Test: Test Method(s) 3:

Coatings Abrasion ASTM D4060, D3884; Chrysler LP-463KB-21-01;

FLTM BN 107-01; FLTM BN 108-02; GM 9515P, 9905P; GMW 3208; ISO 9352 (1995); SAE J575; PV3906; PV 3366, PV 3949; DBL 5578, section 8.1

Acid Spotting FLTM BI 113-02, BI 113-05 Adhesion ASTM D3359; Chrysler LP-463PB-15-01;

FLTM BI 106-02, BI 106-1; GM 9071P, 9160P, 9502P; GMW 14829, 14695; ISO 2409; DBL 5578, section 7.5; MBN 10494-5, sections 5.1 & 5.4

Aging Chrysler LP-463DD-8-02, LP-463PB-36-01; GM 9329P, 9504P – 2003 (Discontinued)1

Bow & Bias Chrysler LP-463KB-14-01; ASTM D3882 Carbon Arc Weathering DMC - Twin Enclosed Carbon Arc/XW - Sunshine;

ASTM D750, D822, G152, G153, D1499, D3980-88 (Withdrawn 1998)1; Chrysler LP-463PB 12-01

Chemical Resistance LP-463PB-31-01; FLTM BI 152-01; GM 9509P; GMW 14864, 16625

Color – Visual & Instrumented ASTM D2244; SAE J1545; GM 9741P; PV 3965; MBN 10494-4, section 5.2; DIN EN ISO 3668; DIN EN 20105-A02; ASTM D2616; ISO 105-A02

Condensing Humidity ASTM D1735; GMW 14729 Corrodkote ASTM B380

(A2LA Cert. No. 0078.02) Revised 04/23/2018 Page 2 of 11

Test: Test Method(s) 3:

Coatings (Cont.) Creepback GM 9102P; GMW 15282 Degree of Blistering ASTM D714 Dimension GM 9230P, 9452P Fading AATCC 16.3 Falling Sand ASTM D968 (Method A); GM 9542P Gloss ASTM D523; FLTM BI 110.01;

DIN 53236, DIN EN ISO 2813; MBN 10494-4, section 5.1

Chip Resistance ASTM D3170; Chrysler LP-463PB-39-01; GM 9508P; GMW 14700; SAE J400; FLTM BI 107-01; ISO 20567-1; DBL 7399, section 5.3; MBN 10494-5, section 5.2

Hardness, Pencil ASTM D3363; GM 9507P; ES-X71222 (5.7) Knife Peel Test FLTM BI 106-01 Mandrel Bend Test GM 9503P Mildew GM 9215P; GMW 3259 Non-condensing Humidity ASTM D2247; SAE J575 Odor Chrysler LP-463KC-9-01; GM 9130P; GMW 3205;

SAE J1351; TSM 0505G (except 8.3); Honda 0096Z-SEC-000; VW PV3900; EDS-T-7603

Oil Immersion GM 4350M, Appendix B Perspiration Resistance GM 9240P, 9517P; FLTM BI 113-07;

Chrysler LP-463KC-21-01 Fluorescent Weather UVA/UVB ASTM G53-96 (Withdrawn 2000)1, G154; SAE 2020;

AATCC 186 (Option 1, 2, & 3); ASTM D4674 (Method IV) Salt Spray/Humidity/CASS ASTM B117, B368, D1735, D2247;

Chrysler LP-463PB-9-01, LP-463PB-10-01; FLTM BI 103-01; FLTM EU BQ-005-02; GM 4298P, 4465P; SAE J575, J1383; DIN EN ISO 9227-NSS, DIN EN ISO 9227-CASS, DIN EN ISO 6270-2; NES M0140; MIL-STD-202G (Method 101E); SAE J2334; GMW14872; VDA 621-415; PV 1208; PV 1209; DIN EN ISO 4623-2; DBL 7381, section 5.13

Smoke Resistance GM 9742P Spotting GM 9133P Stretch & Set SAE J855 Sulfur Dioxide GMW 14864 Taber Abrasion See Abrasion Thermal Aging/ Thermal Cycling/Humidity Cycling

Chrysler LP-463CB-12-01, LP-463LB-12-01; GM 9131P, 9200P, 9329P, 9504P, 9505P, 9511P, 9619P; GMW 14124; DBL 5471, sections 4.1 and 4.2; PV 1200; PV 2005

Thumbnail Test GM 9507P Water Immersion FLTM BI 104-01, BI 104-04

(A2LA Cert. No. 0078.02) Revised 04/23/2018 Page 3 of 11

Test: Test Method(s) 3:

Coatings (Cont.) Water Resistance ASTM D870;

PV 3922; PV 3959 Water/Soap Spotting FLTM BI 113-01; Chrysler LP 463PB-31-01 (Method F) Accelerated Weathering ASTM D1654; FLTM BO 115-01; GM 9125P Xenon (Interior, Exterior) ASTM D4459, G26-96 (Withdrawn 2000)1,

ASTM D2565, G155 (except methods 9 & 10); SAE J1885 (Withdrawn 2008)1, J1960 (Withdrawn 2008)1; SAE J2412, J2527; NES MO135-2001-N; VW PV1303, PV1502, PV3929, PV3930; AATCC TM 16 (Options 3, 4 & 5); DIN 75 202; Mitsubishi ES-X83239; GMW14162 (Method A, B, & D); HES D6601; TSH 1585G (Type III & IV); TSH 3130 (Method II); TSM 0501G; Ford FLTM BO 116-01; DIN EN ISO 105-B06; PV 1306; DBL 5578, section 13; MBN 10505; MBN 10506

Pressure Washer Test PV 1503; DIN EN ISO 16925; MBN 10494-5 section 5.3

Plastics / Non-Metals Adhesion ASTM D751, 45-48, B571;

Chrysler LP-463LB-10-01, LP-463LB-19-01; GM 9502P, 9774P, 9892P; FLTM BN 151-05

Aging/Thermal Cycle ASTM D865; Chrysler LP-463LB-13-01; GM 9125P, 9142P, 9143P, 9310P; GMW 14124

Chemical Resistance GM 9308P; ASTM D471, D896; ISO 175; DIN EN ISO 4628-1; PV 3964; DBL 5404; DIN EN ISO 4628-1; VDA 621-412

Cleanability Chrysler LP463KC-04-01; GMW 14334 Cleaners (Effect of) GMW 14334 Cold Flex Chrysler LP-463LB-11-01; SAE J323 (Methods A & B);

DBL 5578, section 7.3 Cold Test Chrysler LP-463DD-7-01 Colorfastness to Crocking AATCC TM 8; FLTM BN 107-1; GM 9033P;

SAE J861; AATCC TM 116 Color/Fiber Show-Through GMW 4750 Compatibility ASTM D925; GM 9141P, 9895P Compression Deflection/Recovery ASTM D575, D1056, D1621, D3574-C, D3575-D;

GM 9885P; SAE J1352; ISO 604 Compression Set ASTM D395, D1229, D1056, D3574-D; GS93010-2 (7.4) Compression Strength ASTM D575 (Methods A & B); ISO 604 Conditioning ASTM D618; ISO 291 Corrosiveness for Insulating Materials SAE J1389 Crazing GM 9143P Cure/Solvent Rub GMW 1589, 14333

(A2LA Cert. No. 0078.02) Revised 04/23/2018 Page 4 of 11

Test: Test Method(s) 3:

Plastics / Non-Metals (Cont.) Dimensional Stability ASTM D1204; LP-463LB-7-01;

GM 7400M (3.2.3.1.7), 9452P; SAE J883; GMW 4217

Durometer - Shore Hardness (A & D only)

ASTM D2240; ISO 868

Dust-Out GMW 16998 Flammability ASTM D635; FMVSS 302;

GM 6090M (Note 1), 9070P; SAE J369; UL 94 (7, 8, 9, 12); FTLM BN 024-02; GMW 3232; HES D6003; TSM 0500G; Volvo Std. 5031 (Section 1); Ford ES-E97B-1011-014-AA, ES-X60410; NES MO 094; ISO 3795; MES CF 050C; DIN 75 200, VW PV3904; ANSI/SAE Z26.1 (Section 5.24); FMVSS 302; TSM 0504G; Chrysler DBL 5307; GM/DAEWOO EDS-T-7602; TL 1010 (Note 1)

Flexural Modulus/Strength ASTM D790; ISO 178 Fogging FLTM BO 116-03 (modified to SAE J1756);

GM 9305P; SAE J1756; GMW 3235; TSM 0503G; Honda 0096Z-SEC-A000, 5-11; HES 6508; VW PV3015; NES M0161; ISO 6452; DIN 75201

Brake Hoses Performance Test FMVSS 106 Urethane Foam ASTM D3574 (Sections A, B1, B2, C, D, F, H, I,

J, & K only), D3770; GM 7452M

Heat Deflection Temperature (HDT)

ASTM D648; TSM 0501G

Heat Sag ASTM D3769 Hydrolytic Stability GM 9231P Impact- Cold Slam GM 9773P Impact Resistance ASTM, D5420; Chrysler LP-463DB-14-01;

GM 9300P (non instrumented); GMW 14093; PV 3905; PV 3971; MBN 10494-5 section 5.2

Impact Test Chrysler LP-463PB-19-01, LP-463KB-28-01; FLTM B0151-01; NES MO 134; ISO 6272-2

Izod Impact ASTM D256; ISO 180; TSM0501G; NES M8020 (Section 7)

Charpy Impact ISO 179-1 Laminated Curl GM 9330P Low Temperature Flexibility Ford WSS-M99P32-B, (Section 3.8) Melt Flow Rate ASTM D1238 (Method A); ISO 1133 Migration Staining Chrysler LP-463DD-6-01; GM 9141P; GMW 14141 Moisture Absorption WSS-M99P32-B (Section 3.7)

(A2LA Cert. No. 0078.02) Revised 04/23/2018 Page 5 of 11

Test: Test Method(s) 3:

Plastics / Non-Metals (Cont.) Odor GM 9130P, 9832P; SAE J1351; FLTM BO131-01;

GMW 3205; TSM 0505G; Honda 0096Z-SEC-A000 (Sections 5-12); VW PV3900; EDS-T-7603; VDA 270

Ozone Resistance ASTM D1149, D1171; GM 4486P; SAE J1128 (Section 6.8); ISO 1431-1

Peel Test ASTM D751, D903; FLTM BN 13-1; GM 9797P, 9907P, 3604M, 3602M (Note 1); GMW 15671; TSL5100G; ASTM D3330; PV 2034

Perspiration Resistance Chrysler LP-463KC-21-01; FLTM BI 113-03; GM 9517P; AATCC TM 15

Pile Distortion GMW 3274, 4141 Resistance to Mildew Ford WSS-M99P32-A (Section 3.15) Resistance to Scratching FLTM BN 108-13;

PV 3952; PV 3974; DBL 7384

Rubber Staining Resistance ASTM D925 Rubber Chemical Resistance ASTM D471 Rubber Aging ASTM D865 Scuffing FLTM BN 108-04 Scuff & Mar GM 9150P Soiling & Cleanability FLTM BN 112-08; GMW 3402 Stain Resistance ASTM D925-A Stress Cracking (Marking) GM 9302P;

DIN EN ISO 22088-3; DIN EN ISO 4599 Taber Abrasion See Abrasion Tear Resistance ASTM D1004, D751, 28-31 Tear Strength ASTM D624 (except Die B), D1004, D3574;

Chrysler LP-463KB-3-01; TSM 7500G; TSL 5100G; ASTM D2261, D5733-99 (Withdrawn 2008)1; PV 3946; ISO 34-1; GS93010-2 (7.3)

Temperature Deflection (HUL, HDT, HDUL)

ASTM D648; ISO 75-1, -2

Vicat Softening Temperature of Plastics ASTM D1525; ISO 306 Tensile/Elongation ASTM D412, D638, D882, D5034, D5035;

Chrysler LP-463KB-2-01; TSL 5100G (Section 4.3) ISO 527-1, 2; GMW 3010; TSM 7500G (Section 5.2); DBL 5578 section 7.2; DIN 53504

Thermal Expansion (CLTE) ASTM D696; ISO 4897

Thickness ASTM D1777 D1000, D1813, D5736, C167; SAE J1355, SAE J882; ISO 2589; TSL 2100G, TSL 3505G; FLTM BN114-01

Transverse Strength SAE J949 Thermal Properties ASTM D573 Trapezoidal Tear ASTM D5587, D1117, D751 (Sections 32-35); GMW 3326

(A2LA Cert. No. 0078.02) Revised 04/23/2018 Page 6 of 11

Test: Test Method(s) 3:

Plastics / Non-Metals (Cont.) Volatile Content Loss ASTM D1203, D2369; Chrysler LP-463DD-4-01 Volatile-Solid Content Chrysler LP-463CA-1-01; GM 9010P Volume Change ASTM D471; ISO 1817 Water Absorption ASTM D570, D1056; SAE J315 Water Spotting Chrysler LP-463KC-3-01; GM 9133P; FLTM BI 113-01 Weight/Mass/Mass per area/Density ASTM D3776 (Option C); TSL 2100G (4.47);

TSM 7500G (5.1); GMW 3182; GM 2213M (Note 1); TSL 5100G (Sections 4.1 & 4.2); TSL 3505G (Sections 6.1 & 6.2); ASTM B328, D6242; SAE J860; GM 2737M, 2.1; ISO 1183A

Wicking & Blistering GM 9146P; SAE J913 Xenon NES MO135-2001-N;

ASTM D4459, D2625 (Methods 1-5), G155 (excluding methods 9 & 10), G26; SAE J1885, J1960, J2412, J2527; VW PV3.13.1, PV1303, PV1502, PV3929, PV3930; AATCC TM 16, (Options 3, 4, & 5); DIN 75 202; Mitsubishi ES-X83239; GMW 14162 (Methods A, B & D); HES D6601; TSH 1585G (Type III & IV), TSH 3130 (Method II), TSM 0501G; Ford FLTM BO 116-01

Metallurgical Case Depth SAE J423; ASTM E384 Chrome Spot Test ASTM B556 Coating/Plating Thickness ASTM B487; ISO 1463;

FLTM BI 117-1 (magnetic substrate only); DIN 50600, DIN EN ISO 1463; ASTM B504; ISO 2808, method 7D; ISO 2360; ISO 2177

Decarburization GM 6104M (Note 1); SAE J419 Discontinuous Chromium GMW 14668;

PV 1058; PV 1063 Grain Size ASTM E112 Inclusion Content ASTM E45; SAE J422 Iron Castings-Graphite ASTM A247; GM 6129M (Note 1); GMW 10 Macroetching ASTM E340 Microetching ASTM E407 Metallurgical Preparation ASTM E3;

IPC-TM-650, 2.1.1 Microhardness (Case or Core/Knoop/Vickers) Loads: 200, 500

ASTM E384

Plating STEP Test ASTM B764; PV 1065

Pore Count GM 4372M (Note 1) Rockwell Hardness ASTM E18 Saw Grind ASTM B571 (Section 8) Tensile/Yield/Elongation ASTM E8; ISO 6892-1 Weld Evaluation GM 4488M, 6122M (Note 1); Chrysler PS 9472;

GMW 14058

(A2LA Cert. No. 0078.02) Revised 04/23/2018 Page 7 of 11

Test: Test Method(s) 3:

Glass Abrasion Resistance ATPD 2352, 3.3.6, 4.3.6;

ANSI/SAE Z26.1, 5.17, 5.18 Bond Integrity ATPD 2352, 4.3.1.3; Chemical Exposure ATPD 2352, 3.3.7.2, 4.3.7.2;

ANSI/SAE Z26.1, 5.19, 5.20 Dimensional Stability ANSI/SAE Z26.1, 5.21 Flexibility ANSI/SAE Z26.1, 5.2.2 Flammability ANSI/SAE Z26.1, 5.23, 5.24 High Temperature ATPD 2352; ANSI/SAE Z26.1, 5.5;

MIL-STD-810F (Method 501.4) Humidity ATPD 2352, 3.3.2, 4.3.2; ANSI/SAE Z26.1, 5.3;

MIL-STD-810F (Method 507.4-1) Impact Resistance (Ball Drop/Dart Drop)

ANSI/SAE Z26.1, 5.8-5.14; IEC 60601-1-11, section 15.3.3

Low Temperature ATPD 2352P, 3.4, 4.4; ANSI/SAE Z26.1; MIL-STD-810F (Method 502.4)

Optical Analysis (Luminous Transmittance/Haze/Optical Deviation/ Optical Distortion)

ATPD 2352; ANSI/SAE Z26.1; MIL-DTL-62420; ASTM D1003, F801, F2156

Temperature Shock ATPD 2352, 3.3.4, 4.3.4; ANSI/SAE Z26.1, 5.2, 5.15; MIL-STD-810F (Method 503.4)

Sun Exposure/Weathering ATPD 2352, 3.3.5, 4.3.5; ANSI/SAE Z26.1, 5.16; MIL-STD-810F (Method 505)

Window Lamination ATPD 2352, 4.3.1.3 Vibration, Mechanical Durability, and Fatigue

Vibration Testing Methods for Automobile Parts

JIS D 1601

Vibration Testing of Shipping Containers ASTM D999 Vibration Testing of Switches GM 9110P, 7.7.4.1 Shock & Vibration Testing MIL-STD-810E, 514 & 516;

IEC 60601-1-11 (Sections 10.1.2a, 10.1.2b, 10.1.3a, 10.1.3b, & 10.1.3c)

Drop/Impact Testing IEC 60601-1-11 (Section 10.1.3d) Vibration testing of Lamp Assemblies SAE J575, SAE J1383

Accelerated Stress Testing in accordance with customer profile requirements.

FMVT, HALT, HAST, HASS, MEOST, ALT

Single Axis Electrodynamic Vibration Sine up to 13,000 lbf Random up to 11,000 lbf 2 in. peak to peak stroke

Servo-hydraulic Single Axis Fatigue 4 in. peak to peak stroke

Shipping Simulation of Packaged Products

On the following types of materials and products:

Automotive components, consumer products, electronic circuits, cables, and connectors. Using industry and customer driven specifications

(A2LA Cert. No. 0078.02) Revised 04/23/2018 Page 8 of 11

Test: Test Method(s) 3:

Furniture Testing Custom design testing fixturing and machinery, custom designed programs, fire testing /flammability, prototype designed testing programs, static and electro-mechanical cycling, rack test, lock test.

General Purpose Office Chairs ANSI/BIFMA X5.1, Test No. 5-21; ANSI/BIFMA X5.11

Educational Seating ANSI/BIFMA X6.1

Vertical Files ANSI/BIFMA X5.3, Test No. 4-14

Lounge Seating ANSI/BIFMA X5.4, Test No. 5-22

Desk/Table Products ANSI/BIFMA X5.5, Test No. 4-19; BS EN 527-2;

CAN/CGSB 44.227

Panel Systems ANSI/BIFMA X5.6, (Sections 5.1.1-10.19)

(excluding Section 4)

Storage Units ANSI/BIFMA X5.9, Test No. 4-17;

ASTM F2057-14; ASTM F3096-14

Cabinet Hardware ANSI/BHMA 156.9, (Sections 4.1-4.16)

Kitchen and Vanity Cabinets ANSI/KCMA A161.1, (Sections 4-9)

Small Office/Home Office ANSI/SOHO S6.5, (Sections 4-20)

Access Floor Panel Testing CISCA, (Sections 1-8 and 10)

Intensive Use Chairs FED-STD 834A (Sec 5.1-5.13)

Safety Requirements EN 1335-2, (Sections 4.1-4.5)

Office Furniture-Office Work Chair EN 1335-3, Safety Requirements, Test No. 5-9

Lab Furniture SEFA 8, (Sections 4.2-10.2)

Furniture-Seating (Europe) EN 1728; ENV 12520, 15373; BS 5459

Furniture-Beds and Mattresses (Europe) EN 1725; EN 1957; EN 16139

Methods of test for assessment of the

ignitability of upholstered seating by

smoldering and flaming ignition sources

BS 5852

Testing the Flame Retardance of

Upholstered Furniture

CAL TB-116

Flame Retardance of Resilient Filling

Materials Used in Upholstered Furniture

CAL TB-117

Standard for the Flammability of

Mattresses

16 CFR Part 1632

Standard for the Flammability of Mattress

Sets (open flame)

16 CFR Part 1633

Furniture-Assessment of the Ignitability of

Upholstered Furniture Part 1: Ignition

Source Smoldering Cigarette

BS EN 1021-1

Furniture-Assessment of the Ignitability of

Upholstered Furniture Part 2: Ignition

Source Match Flame Equivalent

BS EN 1021-2

Mattresses for Use in Public Buildings CAL TB-129

Furniture Seating Fire Test CAL TB-133

Standard Test Methods for Evaluation of

Innersprings, Box Springs, Mattresses, or

Mattress Sets

ASTM F1566

Upholstered Furniture Test Method GSA FNAE-80-214A

(A2LA Cert. No. 0078.02) Revised 04/23/2018 Page 9 of 11

Test: Test Method(s) 3:

Furniture Testing (Cont.)

Furniture - Ranked seating - Test Methods

and Requirements for Strength and

Durability

EN 12727

Assessment of the Ignitability of

Mattresses, Upholstered Divans and

Upholstered Bed Bases with Flaming

Types of Primary and Secondary Sources

of Ignition

BS 6807

Furniture-Assessment of the Ignitability

of Mattresses and Upholstered Bed Bases.

Ignition Source: Smoldering Cigarette

BS EN 597-1

Furniture-Assessment of the Ignitability

of Mattresses and Upholstered Bed Bases.

Ignition Source: Match Flame Equivalent

BS EN 597-2

Standard Methods of Tests and

Classification System for Cigarette

Ignition Resistance of Components of

Upholstered Furniture

NFPA 260

Hoist for Transfer of Disable Persons ISO 10535 Sec. 8.3

Cycle Speed and Cycle Time: per Test Method or Customer Request

Loading Force: per Test Method or Customer Request

Durability Testing Stroke Length: 0 to 42”

Loading and Stroke Angles: 0 to 360º

Drop Height and Drop Weight: per Test Method or Customer Request “Customer Specific” methods based on the technologies listed above

Test: Test Method(s) 3:

Lighting 100' Goniophotometric system, BM-7 luminance colorimeter; Bench-top spectroradiometer, 1 meter Integrating sphere/spectoradiometer system Forward Lighting Devices SAE J95, J518, J575, J581, J582, J583, J852, J1383, J1735,

J2009, J2087, JIS 32, JIS 33; ECE: R1, R5, R8, R19, R20, R98, R99; FMVSS 108; GMW14906

Signaling, Marking, and Rear Lighting Devices, Reflex Testing

SAE, J575, J594, JIS 38, J186, J222, J585, J586, J587, J588, J591, J592, J593, J594, J914, J1319, J1373, J1395, J1398, J1424, J1432, J1889, J2039, J2040, J2042, J2139, J2261; FMVSS 108; ECE R3; GMW14906

Colorimetry SAE J578 Photometry of Retro-reflective Materials SAE J1967 Warning Lamps and Devices SAE J595, J744, J887, J974, J975, J845 Agricultural Machinery SAE J137, J974, J975 Construction and Industrial Machinery SAE J95, J96, J99, J598, J1029, J1623 All-Terrain Vehicles SAE J1623

(A2LA Cert. No. 0078.02) Revised 04/23/2018 Page 10 of 11

Test: Test Method(s) 3:

Lighting (Cont.)

Motorcycles SAE J131, J584, J852, J1306; ECE R50, R53, R56, R57, R74, R82

Snowmobiles SAE J278, J279, J280, J292 Dust Testing SAE J575, J1383; FMVSS 108 FAA / Airport FAA 150/5340-5C, 150/5340-18F, 150/5340-26B,

150/5345-12F, 50/5345-39D, 150/5345-43F, 150/5345-44J, 150/5345-46D, 150/5345-50B, 150/5345-51B, 150/5345-53C, 150/5345-55A

Emergency Vehicle GSA/FED KKK-A-1822F, (Section 3.8) Luminous Flux IES-LM-45 Failure Analysis Acceptability of Electronic Assemblies IPC-A 610 Corrosion, Fatigue, Contamination & Weld Evaluation on Metals, Plastics, Composites, Paints,

Using industry and customer specifications related to the methods listed in this Scope of Accreditation.

Fractrographic Analysis, Microstructure, Micro-infrared analysis Finite Element Analysis, Stress Analysis

Measurement Vehicle Test Fit CAPA QSM Appendix J

Dimensional 4

Parameter

Range

CMC 5 ()

Technique

Length 12 ft / 3.6m sphere ± 0.0014 in / ±0.036 mm CMM-ROMER Note 1: The laboratory is accredited for the test methods listed above. The accredited test methods are used in determining compliance with the material specifications indicated with a (Note 1). However, the inclusion of these material specifications on this Scope does not confer laboratory accreditation to the material specifications.

1 This laboratory’s scope contains withdrawn or superseded methods. As a clarifier, this indicates that the

applicable method itself has been withdrawn or is now considered “historical” and not that the

laboratory’s accreditation for the method has been withdrawn.

2The Consumer Product Safety Improvement Act (CPSIA) requires that every children's product subject

to a federal consumer product safety requirement be tested by a Consumer Product Safety Commission

(CPSC) accepted laboratory for compliance with the applicable federal children's product safety

requirements. Accreditation by A2LA does not infer acceptance by the CPSC. Please verify this

organization’s acceptance status by using the CPSC’s searchable database, located at

http://www.cpsc.gov/cgi-bin/labsearch/.

(A2LA Cert. No. 0078.02) Revised 04/23/2018 Page 11 of 11

3 For standards or methods listed on the scope of accreditation without a revision date, laboratories are expected to be competent in the use of the current version within one year of the date of publication of the standard test method or upon the date specified by the standard test method originator when the originator has implementation authority. When a superseded standard or method is required for an accredited test, the scope will include the superseded date/version.

4 This test is not equivalent to that of a calibration. 5 “Calibration and Measurement Capability” (CMC) is the smallest uncertainty of measurement that a laboratory can achieve within its scope of accreditation when performing more or less routine calibrations of nearly ideal measurement standards of nearly ideal measuring equipment. CMC represent expanded uncertainties expressed at approximately the 95 % level of confidence, usually using a coverage factor of k = 2. The actual measurement uncertainty of a specific calibration performed by the laboratory may be greater than the CMC due to the behavior of the customer’s device and to influences from the circumstances of the specific calibration.

For the tests to which this accreditation applies, please refer to the laboratory’s Mechanical Scope of Accreditation.

Accredited Laboratory

A2LA has accredited

INTERTEK TESTING SERVICES NA, INC. Kentwood, MI

for technical competence in the field of

Mechanical Testing

This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005

General requirements for the competence of testing and calibration laboratories. This accreditation demonstrates

technical competence for a defined scope and the operation of a laboratory quality management system

(refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009).

Presented this 27th day of February 2017.

_______________________

President and CEO

For the Accreditation Council

Certificate Number 0078.02

Valid to December 31, 2018