Upload
bartholomew-wheeler
View
223
Download
0
Embed Size (px)
Citation preview
Measurement
Why are precise measurements and calculations essential to a
study of physics?
Measurement & Precision
The precision of a measurement depends on the instrument used to measure it.
For example, how long is this block?
Measurement & Precision
Imagine you have a piece of string that is exactly 1 foot long.
Now imagine you were to use that string to measure the length of your pencil. How precise could you be about the length of the pencil?
Since the pencil is less than 1 foot, we must be dealing with a fraction of a foot. But what fraction can we reliably estimate as the length of the pencil?
Measurement & Precision
Suppose the pencil is slightly over half the 1 foot string. You guess, “Well it must be about 7 inches, so I’ll say 7/12 of a foot.”
Here’s the problem: If you convert 7/12 to a decimal, you get 0.583.
Can you reliably say, without a doubt, that the pencil is 0.583 and not 0.584 or 0.582?
You can’t. The string didn’t allow you to distinguish between those lengths… you didn’t have enough precision.
So, what can you estimate, reliably?
Measurement & Precision
Basically, you have one degree of freedom… one decimal place of freedom.
So, the only fractions you can use are tenths! You can only reliably estimate that the pencil is 0.6
ft long. It’s definitely more than 0.5 ft long and definitely less than 0.7 ft long.
Thus, precision determines the number of significant figures we use to report measurements.
In order to increase the precision of their measurements, physicists develop more-advanced instruments.
How big is the beetle?
Copyright © 1997-2005 by Fred Senese
Measure between the head and the tail!
Between 1.5 and 1.6 in
Measured length: 1.54 in
The 1 and 5 are known with certainty
The last digit (4) is estimated between the two nearest fine division marks.
How big is the penny?
Copyright © 1997-2005 by Fred Senese
Measure the diameter.
Between 1.9 and 2.0 cmEstimate the last digit.
What diameter do you measure?
How does that compare to your classmates?
Is any measurement EXACT?
What Length is Indicated by the Arrow?
Significant Figures
Indicate precision of a measured value 1100 vs. 1100.0 Which is more precise? How can you tell? How precise is each number? Determining significant figures can be tricky. There are some very basic rules you need to
know. Most importantly, you need to practice!
Counting Significant Figures
The Digits Digits That Count Example # of Sig Figs
Non-zero digits ALL 4.337 4
Leading zeros(zeros at the BEGINNING)
NONE 0.00065 2
Captive zeros(zeros BETWEEN non-zero digits)
ALL 1.000023 7
Trailing zeros (zeros at the END)
ONLY IF they follow asignificant figure AND
there is a decimalpoint in the number
89.00 but
8900
4 2
Leading, Captive AND Trailing Zeros
Combine therules above
0.003020 but
3020
4
3
Scientific Notation ALL 7.78 x 103 3
Calculating With Sig Figs
Type of Problem Example
MULTIPLICATION OR DIVISION:
Find the number that has the fewest sig figs. That's how many sig figs should be in your answer.
3.35 x 4.669 mL = 15.571115 mLrounded to 15.6 mL
3.35 has only 3 significant figures, so that's how many should be in the answer. Round it off to 15.6 mL
ADDITION OR SUBTRACTION:
Find the number that has the fewest digits to the right of the decimal point. The answer must contain no more digits to the RIGHT of the decimal point than the number in the problem.
64.25 cm + 5.333 cm = 69.583 cm rounded to 69.58 cm
64.25 has only two digits to the right of the decimal, so that's how many should be to the right of the decimal in the answer. Drop the last digit so the answer is 69.58 cm.
Scientific Notation
Number expressed as: Product of a number between 1 and 10 AND a power of 10
5.63 x 104, meaning 5.63 x 10 x 10 x 10 x 10 or 5.63 x 10,000
ALWAYS has only ONE nonzero digit to the left of the decimal point
ONLY significant numbers are used in the first number First number can be positive or negative Power of 10 can be positive or negative
When to Use Scientific Notation
Astronomically Large Numbers mass of planets, distance between stars
Infinitesimally Small Numbers size of atoms, protons, electrons
A number with “ambiguous” zeros 59,000
HOW PRECISE IS IT?
Powers of 10
Positive Exponents
000,101010101010
100010101010
100101010
1010
4
3
2
1
Exponent of Zero Means “1” 100 = 1
Powers of 10
Negative Exponents
0001.010
001.010
01.010
1.010
000,101
101
101
101
1014
10001
101
101
1013
1001
101
1012
1011
Exponent of Zero Means “1” 100 = 1
Converting From Standard to Scientific Notation
Move decimal until it is behind the first sig fig Power of 10 is the # of spaces the decimal moved Decimal moves to the left, the exponent is positive Decimal moves to the right, the exponent is negative
428.5 4.285 x 102
(decimal moves 2 spots left)
0.0004285 4.285 x 10-4
(decimal moves 4 spots right)
Converting From Scientific to Standard Notation
Move decimal point # of spaces the decimal moves is the power of 10 If exponent is positive, move decimal to the right If exponent is negative, move decimal to the left
4.285 x 102 428.5(move decimal 2 spots right)
4.285 x 10-4 0.0004285(decimal moves 4 spots left)
Systems of Measurement
Why do we need a standardized system of measurement? Scientific community is global. An international “language” of measurement allows
scientists to share, interpret, and compare experimental findings with other scientists, regardless of nationality or language barriers.
By the 1700s, every country used its own system of weights and measures. England had three different systems just within its own borders!
Metric System & SI The first standardized system of measurement: the
“Metric” system Developed in France in 1791 Named based on French word for “measure” based on the decimal (powers of 10)
Systeme International d'Unites(International System of Units) Modernized version of the Metric System Abbreviated by the letters SI. Established in 1960, at the 11th General Conference on
Weights and Measures. Units, definitions, and symbols were revised and simplified.
Components of the SI System
In this course we will primarily use SI units. The SI system of measurement has 3 parts:
base units derived units prefixes
Unit: measure of the quantity that is defined to be exactly 1
Prefix: modifier that allows us to express multiples or fractions of a base unit
As we progress through the course, we will introduce different base units and derived units.
SI: Base Units
Physical Quantity Unit Name Symbol
length meter m
mass kilogram kg
time second s
electric current ampere A
temperature Kelvin K
amount of substance mole mol
luminous intensity candela cd
SI: Derived Units
Physical Quantity Unit Name Symbol
area square meter m2
volume cubic meter m3
speed meter persecond
m/s
accelerationmeter per
second squaredm/s2
weight, force newton N
pressure pascal Pa
energy, work joule J
Prefixes
Prefix Symbol Numerical MultiplierExponentialMultiplier
yotta Y 1,000,000,000,000,000,000,000,000 1024
zetta Z 1,000,000,000,000,000,000,000 1021
exa E 1,000,000,000,000,000,000 1018
peta P 1,000,000,000,000,000 1015
tera T 1,000,000,000,000 1012
giga G 1,000,000,000 109
mega M 1,000,000 106
kilo k 1,000 103
hecto h 100 102
deca da 10 101
no prefix means: 1 100
PrefixesPrefix Symbol Numerical Multiplier
ExponentialMultiplier
no prefix means: 1 100
deci d 0.1 10¯1
centi c 0.01 10¯2
milli m 0.001 10¯3
micro 0.000001 10¯6
nano n 0.000000001 10¯9
pico p 0.000000000001 10¯12
femto f 0.000000000000001 10¯15
atto a 0.000000000000000001 10¯18
zepto z 0.000000000000000000001 10¯21
yocto y 0.000000000000000000000001 10¯24
Unit Conversions
Method “Staircase” Factor-Label
Type Visual Mathematical
What to do…
Move decimal point the same number of places as steps between unit prefixes
Multiply measurement by conversion factor, a fraction that relates the original unit and the desired unit
When to use…
Converting between different prefixes between kilo and milli
Converting between SI and non-SI units
Converting between different prefixes beyond kilo and milli
“Staircase” Method
Draw and label this staircase every time you need to use this method, or until you can do the
conversions from memory
“Staircase” Method: Example
Problem: convert 6.5 kilometers to meters Start out on the “kilo” step. To get to the meter (basic unit) step, we need
to move three steps to the right. Move the decimal in 6.5 three steps to the
right Answer: 6500 m
“Staircase” Method: Example
Problem: convert 114.55 cm to km Start out on the “centi” step To get to the “kilo” step, move five steps to the
left Move the decimal in 114.55 five steps the left Answer: 0.0011455 km
Factor-Label Method
Multiply original measurement by conversion factor, a fraction that relates the original unit and the desired unit. Conversion factor is always equal to 1. Numerator and denominator should be equivalent
measurements. When measurement is multiplied by
conversion factor, original units should cancel
Factor-Label Method: Example
Convert 6.5 km to m First, we need to find a conversion factor that
relates km and m. We should know that 1 km and 1000 m are
equivalent (there are 1000 m in 1 km) We start with km, so km needs to cancel when we
multiply. So, km needs to be in the denominator
km 1
m 1000
Factor-Label Method: Example
Multiply original measurement by conversion factor and cancel units.
m 6500km 1
m 1000km 5.6
Factor-Label Method: Example
Convert 3.5 hours to seconds If we don’t know how many seconds are in an
hour, we’ll need more than one conversion factor in this problem
seconds 13000 :Answer
(2) figs sig ofnumber eappropriat toround
seconds 12600minute 1
seconds 60
hour 1
minutes 60hours 5.3