Upload
juniorradaic
View
305
Download
9
Embed Size (px)
Citation preview
7/30/2019 MB0120120108 HS-450i Operator's Manual
1/152
MB012012-01-08
HS-450i
Operators Manual
7/30/2019 MB0120120108 HS-450i Operator's Manual
2/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
Table of Content1 Safety Precautions 41.1 Potential Hazards 41.2 Safety Labels and Plates 51.3 Safety Devices 241.4 Safety Instructions 24
2 Controls and Operations 292.1 Electric Cabinet 292.2 Operation Console 312.3 Operation Panel 332.4 Other Controls and Pushbuttons 59
3 Starting and Ending Operation 663.1 Emergency Stop 663.2 Turning ON Power 663.3 Machine Warm-up 673.4 Turning OFF Power 693.5 After Turning Off Power 693.6 Measures in Power Failure 703.7 Weekly Timer 72
4 Manual Operation 744.1 Zero Point Return 744.2 JOG Feed 754.3 Rapid Traverse 764.4
Handle Feed 77
4.5 Insertion/Removal of Spindle Tool 784.6 Spindle Revolution and Stop 79
5 MDI Operation 805.1 MDI (Manual Data Input) Operation 805.2 Spindle Revolution in MDI 815.3 Spindle Orientation in MDI 825.4 ATC Magazine Indexing and Tool 835.5 Table Clamp/Unclamp in MDI Operation 84
6 Automatic Operation 856.1 Starting Automatic Operation 866.2 Stopping & Restarting Automatic 876.3 Door Safety Interlock 89
7 ATC Operation 927.1 Setting up ATC Magazine 927.2 Tool Registration 92
2
7/30/2019 MB0120120108 HS-450i Operator's Manual
3/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
7.3 Single Arm Manual Operation 987.4 Tool Exchange in MDI Operation 997.5 Tool Exchange in Automatic Operation 1017.6 Tool Data Screen 104
8 APC Operation 1068.1 Movement of APC 1068.2 Pallet Indexing Lever 1068.3 APC in Manual Operation 1088.4 APC in MDI Operation 1108.5 APC in Automatic Operation 111
9 Emergency Stop 1129.1 Cases of Emergency 1129.2 To Release Emergency Stop Status 112
10 Interference 11310.1 Workpiece Dimensions 11310.2 Travels of Axes 11410.3 Interference with Spindle 11710.4 Pallet Usable Area 12010.5 Limitation on Tools Dimensions 12110.6 Interference at ATC 12210.7 Pull Stud 124
11 Functions Codes (M Codes) 12511.1 M Code List 125
12 Alarm Message and Operator Message 12812.1 Alarm Messages 12812.2 Operator Message 132
13 Custom Macro Program 13514 Chip Conveyor 13614.1 Controls 13614.2 Alarm 137
15 Weekly Timer Setup 13815.1 Outline of Weekly Timer 13815.2 Same Operation Hours For Each Day 14115.3 Different Operation Hours For Different Day 14415.4 Operation Hours Span Over Multiple Days 149
3
7/30/2019 MB0120120108 HS-450i Operator's Manual
4/152
AVEREX Automation CO., Ltd.
1 Safety PrecautionsAlways keep this manual in a designated area, preferably nears by this
machine, so that every personnel can read it and thoroughly understand allsafety precautions.
1.1 Potential HazardsWhen a maintenance operation requires that machine enclosures beremoved or door interlocks be disabled, it creates a condition that personnel
are potentially exposed to hazards. In such situation, all personnel mustobserve the best safety practice to avoid the potential dangers.
During normal operations, door interlock devices must never be disabled or
bypassed, and enclosures must never be removed.
1.1.1 Electric ShockHS-450i has several subsystems powered by high voltage electricity. Theelectricity is usually not hazardous during most operations. However, if formaintenance purpose, the enclosures are removed or door interlocks are
disabled, the following few areas can endanger personnel with electric shock:
Electric cabinet Coolant pumps Lubrication pump Spindle Oil Chiller Motors
Read all applicable manuals and follow their warnings to avoid accidental
electric shock. Operators must never remove shields or panels, nor shouldoperators bypass or otherwise disable locks.
1.1.2 Moving Machine AreasBecause of the fast moving motions of the mechanisms, getting too close to
the machine in the following areas can result in serious bodily injury to thepersonnel.
Spindle head and column in motion.
HS-450i Operator's Manual
4
7/30/2019 MB0120120108 HS-450i Operator's Manual
5/152
Spindle where a cutting tool in rotating motion. Nearby Automatic Tool Change Area where its mechanism is in motion. Nearby Automatic Pallet Change Area where its mechanism is in motion. Nearby Chip Conveyer in motion.
1.1.3 Sharp Edges on MaterialBe aware of potential dangers posed by sharp edges of materials or fixtures.
1.1.4 Cutting ToolsBe aware of potential dangers posed by the cutting tool(s) in the spindle or
in Automatic Tool Changer.
1.2 Safety Labels and Plates
These labels and plates are affixed on the enclosures of machine as depictedin the drawings. Some of these labels are used to emphasize the hazardous
situations that could result in serious injury or death when using the
machine. Read the warnings carefully and follow the instructions to avoidserious injury or death.
AVEREX Automation Co., Ltd.
HS-450i Operator's Manual
5
7/30/2019 MB0120120108 HS-450i Operator's Manual
6/152
1.2.1 Locations of Labels and Plates
Front Side
AVEREX Automation Co., Ltd.
HS-450i Operator's Manual
6
7/30/2019 MB0120120108 HS-450i Operator's Manual
7/152
Operator Side
AVEREX Automation Co., Ltd.
HS-450i Operator's Manual
7
7/30/2019 MB0120120108 HS-450i Operator's Manual
8/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
Tool Magazine Side
Top
8
7/30/2019 MB0120120108 HS-450i Operator's Manual
9/152
Back Side
AVEREX Automation Co., Ltd.
HS-450i Operator's Manual
Lifting Devices
9
7/30/2019 MB0120120108 HS-450i Operator's Manual
10/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.AVEREX Automation Co., Ltd.
Top View
10
7/30/2019 MB0120120108 HS-450i Operator's Manual
11/152
AVEREX Automation Co., Ltd.
Tool Changer
HS-450i Operator's Manual
11
7/30/2019 MB0120120108 HS-450i Operator's Manual
12/152
1) Tool Specification PlateBBT Tool
AVEREX Automation Co., Ltd.
HS-450i Operator's Manual
12
7/30/2019 MB0120120108 HS-450i Operator's Manual
13/152
CAT Tool
AVEREX Automation Co., Ltd.
HS-450i Operator's Manual
13
7/30/2019 MB0120120108 HS-450i Operator's Manual
14/152
2) Warning Moving Part Hazard
3) Warning Rotating Mechanism Hazard
AVEREX Automation Co., Ltd.
HS-450i Operator's Manual
14
7/30/2019 MB0120120108 HS-450i Operator's Manual
15/152
4) Warning Opened Door Hazard
5) M Code List
AVEREX Automation Co., Ltd.
HS-450i Operator's Manual
15
7/30/2019 MB0120120108 HS-450i Operator's Manual
16/152
6) Safety Instruction Plate
7) Machine Warm-up Instruction
AVEREX Automation Co., Ltd.
HS-450i Operator's Manual
16
7/30/2019 MB0120120108 HS-450i Operator's Manual
17/152
8) Warning - Electric Shock
9) Danger Electrical Shock Hazard
10)Manufacturer Plate
AVEREX Automation Co., Ltd.
HS-450i Operator's Manual
17
7/30/2019 MB0120120108 HS-450i Operator's Manual
18/152
11)Solenoid/Limit Switch
AVEREX Automation Co., Ltd.
HS-450i Operator's Manual
18
7/30/2019 MB0120120108 HS-450i Operator's Manual
19/152
12)Warning - Hot Surface
13)Maintenance Schedule
AVEREX Automation Co., Ltd.
HS-450i Operator's Manual
19
7/30/2019 MB0120120108 HS-450i Operator's Manual
20/152
14)Lubrication Points
AVEREX Automation Co., Ltd.
HS-450i Operator's Manual
20
7/30/2019 MB0120120108 HS-450i Operator's Manual
21/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
15)Lubrication Oil Instruction
16)Pneumatic Air Instruction
21
7/30/2019 MB0120120108 HS-450i Operator's Manual
22/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
17)Axial Directions
19)Oil Drain
Y+
X
Z+
18) (Reserved)
(Space reserved)
22
7/30/2019 MB0120120108 HS-450i Operator's Manual
23/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
20)Lifting Point
21)Oil Filler
22)Lifting Point Forklift
23)Main Power Switch
23
7/30/2019 MB0120120108 HS-450i Operator's Manual
24/152
1.3 Safety DevicesHS-450i is equipped with various types of safety devices that are designed
to protect personnel from accidental injuries. All personnel must learn touse these safety devices before operating or servicing the machine.
Safety Device Where Located
EMERGENCY STOP
pushbuttons
On the Operation Panel
On the side of the Pallet set-up door
On the side of the ATC door
Main Power Switch On the electric cabinet
Door Safety Interlock On the Pallet set-up door
On the Operator side doorOn the ATC door
Key Electric cabinet
Alarm Messages On the LCD display
1.4
Safety Instructions
Safety Instructions are classified into three categories, DANGERWARNING,
and CAUTION subjects to the degree of potential hazard to the personnel.
DANGER Indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION Indicates a potentially hazardous situation which, if not avoided,may result in minor or moderate injury or property damage.
AVEREX Automation Co., Ltd.
HS-450i Operator's Manual
24
7/30/2019 MB0120120108 HS-450i Operator's Manual
25/152
1.4.1 General Instructions Wear proper apparel. Do not wear loose clothing, gloves, neckties,
rings, bracelets, or other jewelry that might be caught in moving parts
or areas of potential electric shock. Non-slip footwear is recommended.
Tie long hair back and wear protective hair covering to contain longhair.
Keep tools sharp and clean for best performance and to reduce the riskof injury. Follow instructions for lubrication and for changing
accessories. Use the proper tools. Do not use tools or attachments to perform a job
for which they were not designed for. Keep proper footing and balance at all times. Use a steady object for
support when reaching over the machine. Do not operate the machine in an unsafe environment. Do not use the
machine in damp or wet locations, or expose to rain. Keep the work area well lighted. The machine is not intended for use with flammable or harmful
substances.
Do not turn the machine on or try to operate it if there are explosiveor flammable gases present.
Use recommended accessories to avoid the risk of injury. Wipe up spills. Immediately cover with absorbent material and wipe up
coolant and oil spills around the machine. Correct the cause of the
leakage to prevent any hazards. The poly-carbonate viewing panels are an integral part of safety
enclosure for the machine. They must be inspected regularly for anysigns of reduced effectiveness (such as cracking or crazing) and
replaced immediately, if such signs or other indications of reducedeffectiveness are noticed.
1.4.2 Machine Installation
Only factory authorized individuals from Akari Seiki or distributors ofAkari Seki may install this machine.
Any electrical installation of the machine must be done by a qualifiedelectrician.
When used to install this machine, cranes, forklifts, and alike must beoperated by licensed operators.
Use appropriate equipments to handle heavy objects.
AVEREX Automation Co., Ltd.
HS-450i Operator's Manual
25
7/30/2019 MB0120120108 HS-450i Operator's Manual
26/152
1.4.3 Before Powering OnBefore powering on the machine, check or inspect the following areas to
ensure safe operations:
All safety devices are functional. Lubrication tank has adequate lubrication oil. Coolant units have adequate coolant. Chips are not accumulated on the telescopic covers. No material or tool is left unintentionally in the machines moving
areas.
No damage in electrical wirings or components. Electrical cables and wires are connected securely. Electrical cabinet is securely closed and No leak in the pneumatic system. Only tools that meet the tool specifications are used
Note Read and understand the Operators Manual before operating this
machine.
1.4.4 Power On and Warming-up Any electrical installation of the machine must be done by qualified
electricians. Check that all protective devices and door interlocks are functional. All guards are firmly in place and show no damages. Follow the procedure and instructions described in the Operators
Manual to power on the machine.
Execute machine warm-up procedure as described in Section 3.3Machine Warm-up of HS-450i Operators Manual.
After the machine has been powered on, check the following items:
No alarm is displayed on the LCD screen No abnormal sound from the motors and gear boxes The cooling fans in the electrical cabinet have been turned on. Spindle and guide ways are adequately lubricated.
AVEREX Automation Co., Ltd.
HS-450i Operator's Manual
26
7/30/2019 MB0120120108 HS-450i Operator's Manual
27/152
1.4.5 During Machine Operation
Read the safety warnings supplied with all tooling. Keep doors closed while machining. Do not disconnect the front door safety switches. Under nocircumstances should the operator open the door before the spindle
stops rotating completely.
Wear ANSI or CE approved safety glassed at all times when operatingthe machine. Everyday glasses are not designed for protection. Only
ANSI or CE approved safety glasses have impact resistant lenses. Do not exceed the Manufacturers recommended maximum RPM for
the tool. When tools are placed in the spindle, verify the current RPMrecommended in the control before starting the spindle rotation.
Always check all parts for binding, breakage, and any other conditionthat may affect the proper operation of the machine and/or increase
the risk of injury. Damaged or missing parts must be repaired or
replaced BEFORE operating the machine. Do not operate the machine under the influence of drugs, alcohol, or
prescribed medication. Use proper safety gloves when handling sharp or jagged edges. Do
not wear gloves around rotating machinery. Use standard machining practices for holding the material that is to be
machined. Keep tools sharp and clean for best performance and reduction of the
risk of injury. Follow instructions for lubrication and for changing
accessories. Tools are designed to perform properly and safely at proper speeds. Take appropriate additional safety precautions and measures when
working with magnesium, wood, or other combustible materials. Hearing protection must be worn when operations exceed 90 (85 CE)
decibels.
Protection is recommended when cutting operations are dusty orexceed the permissible exposure limit.
Dust removal equipment is needed when working with dust-producingmaterials or procedures.
AVEREX Automation Co., Ltd.
HS-450i Operator's Manual
27
7/30/2019 MB0120120108 HS-450i Operator's Manual
28/152
AVEREX Automation Co., Ltd.
1.4.6 Power Off Turn off the power to the machine before leaving the machine
unattended.
Never leave the machine until it has completely stopped.
1.4.7 After Powering Off
Keep work area clean. Good housekeeping practices encourage safety. Do not use air guns to blow away chips.
Always wear gloves when removing chips. Insert a dummy tool into the spindle to prevent debris from entering.
Be aware that the solenoid valves may remain hot for quite a while.
1.4.8 Maintenance Only qualified personnel are authorized to undertake maintenance
work on this machine. Use signs indicating Maintenance in progress to warn people not to
accidentally turn on the machine. Do not enter enclosure area for service or maintenance unless the machine has
been powered off.
Due to danger of slips or falls on a wet or oily surface, any table orenclosure floor that is to be used for maintenance access must be dry
and clean. Never damage, remove, or relocate any part of the limit switches, door
interlocks, or dogs. Wear a hard hat for maintenance or servicing. Always clean up the machine after maintenance work is done. Contact Akari Seiki or your local distributor for all repair parts and
service.
HS-450i Operator's Manual
28
7/30/2019 MB0120120108 HS-450i Operator's Manual
29/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
2 Controls and OperationsHS-450i is built with the following controls to allow certain operations to beperformed by the operator:
Electric CabinetOperation Console
Pallet Operation Control
ATC Control
2.1 Electric Cabinet
CODE DESCRIPTION CODE DESCRIPTION
ACR AC Line Reactor MCP Motor Circuit Breaker
C Capacitor PSM Power Supply Module
D Bridge Rectifier SPM Spindle Amplifier Module
F Circuit Breaker SVM Servo Amplifier Module
G Switching Power Supply R Resistor
INV Inverter SK Surge Suppressor
K Relay T TransformerMC Magnetic Contactor TDON On-delay Timer
MCC Magnetic Contactor
29
7/30/2019 MB0120120108 HS-450i Operator's Manual
30/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
30
7/30/2019 MB0120120108 HS-450i Operator's Manual
31/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
2.2 Operation Console
Green In the mode of Automatic Operation
Red AlarmYellow (lit) End of program executionYellow (blinking) Awaiting pallet setup to complete
Power lamp This lamp lights up whenever power is being supplied
to the operation box.
Main Power Switch This switch turns on or off the supply of the factorypower.
Operator PaneI
Fanuc Main Panel
Fanuc LCD Display
Manual Pulse Generator
31
7/30/2019 MB0120120108 HS-450i Operator's Manual
32/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
2.2.1 NC PushbuttonsNC Power ON Pushbutton (0)
When this button is pressed, NC is powered on and "NOT
READY" appears on the screen after a few seconds.
Note Power on the machine first before pressing NC Power ON pushbutton.
NC Power OFF Pushbutton (00)
When this button is pressed, NC is powered off and LCD
display disappears.
DANGER Always press Emergency Stop pushbutton before pressing NCOFF pushbutton.
DANGER Be sure to press NC OFF pushbutton before turning off Main
Switch of the electric cabinet. If not, NC can potentially bedamaged.
32
7/30/2019 MB0120120108 HS-450i Operator's Manual
33/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
2.3 Operation Panel
67
1 2 3 4
5 6 7 8
9 10 11
12 14 15
22
23
21
25
24
26
28 27
29 30 31
32 33 34
62
71
70
72
63
73
64 65
94 95 96
97 98 99
37 38 39 40 47 48
49 50 51 52 53 54
68 69
56 57
41 42 43
44 45 46
33
7/30/2019 MB0120120108 HS-450i Operator's Manual
34/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
1 EDIT Mode Pushbutton 41 Spindle CW Rotation Pushbutton
2 AUTO Mode Pushbutton 42 Spindle Stop Pushbutton
3 REMOTE Mode Pushbutton 43 Spindle CCW Rotation Pushbutton
4 MDI Mode Pushbutton 44 Spindle Speed Decrease Pushbutton
5 HANDLE Mode Pushbutton 45 Spindle Speed 100% Pushbutton
6 JOG Mode Pushbutton 46 Spindle Speed Increase Pushbutton
7 RAPID Mode Pushbutton 47 B-axis Table Clamp Pushbutton
8 Zero Point Return Mode Pushbutton 48 B-axis Table Unclamp Pushbutton
9 Single Block Pushbutton 49 Door Open Request Pushbutton
10 Optional Stop Pushbutton 50 Auto Power-off Pushbutton
11 Block Skip Pushbutton 51 Air Blow Pushbutton
12 Dry Run Pushbutton 52 Oil & Air System Lubrication Oil Pushbutton
13 (Reserved) 53 Fluorescent Lamp ON/OFF Pushbutton
14 Machine Lock 54 Tool Data Display Pushbutton
15 Program Restart 55 (Reserved)16 (Reserved) 56 Cycle Start Pushbutton
17 (Reserved) 57 Feed Hold Pushbutton
18 (Reserved) 58 Spindle Tool Clamp/Unclamp Pushbutton
19 (Reserved) 59 (Reserved)
20 (Reserved) 60 (Reserved)
21 X-axis Plus Feed Zero Return Pushbutton 61 (Reserved)
22 X-axis Minus Feed Pushbutton 62 Cutting/Jog Feed Override Switch
23 Y-axis Plus Feed Zero Return Pushbutton 63 Chip Auger Forward Pushbutton
24 Y-axis Minus Feed Pushbutton 64 Chip Auger Stop Pushbutton
25 Z-axis Plus Feed Zero Return Pushbutton 65 Chip Auger Reverse Pushbutton
26 Z-axis Minus Feed Pushbutton 66 (Reserved)
27 B-axis Plus Feed Zero Return Pushbutton 67 Emergency Stop Pushbutton
28 B-axis Minus Feed Pushbutton 68 NC Ready Pushbutton
29 Rapid Feed Override 0% Pushbutton 69 Safety Pushbutton
30 Rapid Feed Override 8% Pushbutton 70 Memory Protect Switch
31 Rapid Feed Override 15% Pushbutton 71 Pallet Manual Selection Switch
32 Rapid Feed Override 25% Pushbutton 72 Pallet Set-up Pushbutton
33 Rapid Feed Override 50% Pushbutton 73 Pallet Start Pushbutton
34 Rapid Feed Override 100% Pushbutton 94 F1DT Pushbutton
35 (Reserved) 95 PBLK Pushbutton
36 (Reserved) 96 HINT Pushbutton
37 Cutting Coolant Pushbutton 97 SUNC Pushbutton
38 Flood Coolant Pushbutton 98 JUNC Pushbutton
39 Shower Coolant Pushbutton 99 F2 Pushbutton
40 Spindle Through Coolant Pushbutton
34
7/30/2019 MB0120120108 HS-450i Operator's Manual
35/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
2.3.1 Mode Selection PushbuttonPushbuttons (1) to (8) are Mode selection pushbuttons. Press one of the
pushbuttons to enter its designated mode. When pressed, its lamp willcome on, and the machine will enter the selected mode until changed.
EDIT Mode Pushbutton (1)
Press this button to enter Edit mode. In this mode, programsteps can be modified, inserted, or deleted by using keys on
the NC keyboard.
AUTO Mode Pushbutton (2)
Press this button to enter AUTO mode. In this mode, theprogram stored in the memory can be executed; program
number search and sequence number search of the programin the memory are available.
REMOTE Mode Pushbutton (3)
Press this button to enter Remote mode. In this mode, theprograms read via RS232C interface can be executed.
MDI Mode Pushbutton (4)
Press this button to enter MDI mode. In this mode, data input
is available directly via keys on the NC Operators panel. Theprogram entered through NC Operators Panel can be started
HANDLE Mode Pushbutton (5)
by pressing Cycle Start pushbutton (56).
35
7/30/2019 MB0120120108 HS-450i Operator's Manual
36/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
Press this button to enter HANDLE mode. This mode is usedto provide minute feed with Manual Pulse Generator (82).
Once in this mode, Manual Pulse Generator (82) can be used
to control the movements of the axes.
On Manual Pulse Generator, Axis Selection Switch is used to
select a particular axis to move; Handle Feed Scale Selection
Switch is used set the amount scale of [x1 (=0.001 mm or0.001o), x10 (=0.01 mm or 0.01o), or x100 (=0.1 mm or
0.1o)].
While turning the handle of Manual Pulse Generator (82), theselected axis moves at selected minute feed rate.
JOG Mode Pushbutton (6)
Press this button to enter JOG mode. This mode can be used
to provide continuous feed by manual operation.
Press one of the Plus Direction Feed pushbuttons for X-axis
(21), Y-axis (23), Z-axis (25), or B-axis (27), the selectedaxis will move in the positive direction continuously until it is
released. Press one of the Minus Direction Feed pushbuttonsfor X-axis (22), Y-axis (24), Z-axis (26), or B-axis (28), the
selected axis will move in the negative direction continuouslyuntil it is released.
Note The feed rate can be changed with Feed Rate Override and JOG FeedSetting Switch (62).
In this mode, manual operations of ATC and APC are also allowed.
RAPID Mode Pushbutton (7)
Press this button to enter RAPID mode. This mode is used torun axis at a rapid traverse.
36
7/30/2019 MB0120120108 HS-450i Operator's Manual
37/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
Press one of the Plus Direction Feed pushbuttons for X-axis
(21), Y-axis (23), Z-axis (25), or B-axis (27), the selectedaxis will move in the positive direction at a rapid traverse rate
continuously until it is released. Press one of the Minus
Direction Feed pushbuttons for X-axis (22), Y-axis (24), Z-axis(26), or B-axis (28), the selected axis will move in thenegative direction at a rapid traverse rate continuously until it
is released.
Note The feed rate can be changed with Rapid Feed Override pushbuttons(29) to (34).
Zero Point Return Mode Pushbutton (8)
Press this button to enter Zero Point Return mode. Toexecute Zero Point Return:
1)Press and hold one of the Plus Direction Feed (ZeroReturn) pushbuttons for X-axis (21), Y-axis (23), Z-axis
(25), or B-axis (27).
2)Continue to hold down the pushbutton until its ZeroReturn Completion lamp is lit.
Note Rapid Feed Override pushbuttons (29) to (34) are available for use in
An absolute type encoder is used on each axis of the machine;
therefore, it is not required to execute Zero Point Return afterpowering on the machine.
If a Zero Point Return becomes necessary, it should be performed at
least 100 mm away from its Zero Point.
this mode. Refer to Section 4.1 "Zero Point Return".
37
7/30/2019 MB0120120108 HS-450i Operator's Manual
38/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
2.3.2 Program Execution PushbuttonsPushbuttons (9), (10), (11), and (12) are Program Execution pushbuttons.
Press one of the pushbuttons to enter one of program execution modes.When pressed, its lamp will come on, and the machine will enter that mode
until changed.
Single Block Pushbutton (9)
In AUTO or MDI mode, press this button to enter Single Block
program execution mode. In this mode, the machine stopsafter executing one block of the program. Each subsequent
press of Cycle Start pushbutton (56) results in executing onesingle block.
During G28, G29, or G30, the machine stops at an
intermediate point and Feed Hold pushbutton (57) lights up.
In the canned cycle, the machine stops at the end of the rapidtraverse to the point R and the lamp of Feed Hold pushbutton
(57) comes on. (Refer to FANUC's "Operator's Manual".)
During the time that the machine is temporarily stopped by a
single block; manual and MDI operations are still available tobe executed.
To restart the suspended program, press Cycle Start
pushbutton (56) in the original mode.
Note If a MDI operation is executed during automatic operation or viceversa, modal data affects the latter operation.
If a Single Block is commanded during operation, the machine stops
after it completes executing the current block.
Do NOT press [RESET] key. If [RESET] key is pressed, the next blockof information that has already been read into the buffer storage will
be lost and consequently skipped.
38
7/30/2019 MB0120120108 HS-450i Operator's Manual
39/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
Optional Stop Pushbutton (10)
When in automatic operation, pressing this button causes the
program execution to be in Optional Stop mode.
In this mode, cycle operation is stopped after a blockcontaining M01 is executed, and Program End Signal Light is
lit. To restart cycle operation, press Cycle Start pushbutton
(56).
Block Skip Pushbutton (11)
When in automatic operation, press this button for theprogram execution to enter Block Skip mode.
In this mode, any block beginning with "/" is ignored. If not in
this mode, any block beginning with "/" is executed.
Optional Block Skip is identified when "/" is read into the
buffer from the tape or memory.
Note If a block preceded by a slash has been read into the buffer beforeBlock Skip pushbutton (11) is pressed, it does get executed.
Dry Run Pushbutton (12)
Press this button for the program execution to enter Dry Run
mode. In this mode, all F codes specified in the program areignored. With that, cutting feed is no longer controlled by the
F code, but rather, determined by the JOG Feed rate which isset with Cutting JOG Feed Override switch (62).
In tapping cycle, pressing this button has no effect. In rapidtraverse cycle, this button usually is not in effect. However,
by changing some parameters, this button can be madeeffective for rapid traverse cycle.
39
7/30/2019 MB0120120108 HS-450i Operator's Manual
40/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
Note If operation is stopped in Dry Run, after all axes have completed theirmovements, press this pushbutton (12) again to exit Dry Run mode.
Machine Lock Pushbutton (14)
Pressing this pushbutton causes the machine to enter machine
lock state in which positional changes are displayed on thescreen without the actual axial movements.
When in Machine Lock state, M codes, T codes, and S codes
are still being accepted and can be executed.
Pressing the pushbutton (and Both Hands pushbuttonsimultaneously) again when in Machine Lock state will release
the axial movements from the lock state.
Note Machine Lock pushbutton and Both Hands pushbutton need to be
pressed simultaneously for machine lock to take place.
Note Never release the machine from the Machine Lock State while a
program is being executed.
Program Restart Pushbutton (15)
When a program execution has been stopped, pressing
pushbutton allows the program to continue its execution.
Note Program Restart pushbutton and Both Hands pushbutton need to bepressed simultaneously for program restart to take place.
2.3.3 Direction Feed and Zero Return PushbuttonPlus Direction
40
7/30/2019 MB0120120108 HS-450i Operator's Manual
41/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
X-axis: toward left (Column movement)
Y-axis: upward (Spindle head movement)Z-axis: toward front side (Table movement)
B-axis: clockwise direction (Table turn)
X-axis Plus Direction Feed and Zero Return Pushbutton (21)
This pushbutton can be used to move the X-axis in the
positive direction or to return the X-axis to zero point.
When the machine reaches X-axis zero points as a result ofthe execution of zero point return either by manual operation
or automatic operation (G28), the Zero Return CompletionLamp at the upper-right corner will light up.
X-axis Minus Direction Feed Pushbutton (22)
Pressing this pushbutton moves the X-axis in the negative
direction.
Y-axis Plus Direction Feed and Zero Return Pushbutton (23)
This pushbutton can be used to move the Y-axis in the
positive direction or to return the Y-axis to zero point.
When the machine reaches Y-axis zero points as a result ofthe execution of zero point return either by manual operation
or automatic operation (G28), Y-axis Zero Return CompletionLamp at the upper-right corner will light up.
Y-axis Minus Direction Feed Pushbutton (24)
Pressing this pushbutton moves the Y-axis in the negative
41
7/30/2019 MB0120120108 HS-450i Operator's Manual
42/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
direction.
Z-axis Plus Direction Feed and Zero Return Pushbutton (25)
This pushbutton can be used to move the Z-axis in the
positive direction or to return the Z-axis to zero point.
When the machine reaches Z-axis zero points as a result ofthe execution of zero point return either by manual operationor automatic operation (G28), Z-axis Zero Return CompletionLamp at the upper-right corner will light up.
Z-axis Minus Direction Feed Pushbutton (28)
Pressing this pushbutton moves the Z-axis in the negative
direction.
B-axis Plus Direction Feed and Zero Return Pushbutton (27)
This pushbutton can be used to move the B-axis in the
positive direction or to return the B-axis to zero point.
When the machine reaches B-axis zero points as a result ofthe execution of zero point return either by manual operation
or automatic operation (G28), B-axis Zero Return CompletionLamp at the upper-right corner will light up.
B-axis Minus Direction Feed Pushbutton (28)
Pressing this pushbutton moves the B-axis in the negative
direction.
42
7/30/2019 MB0120120108 HS-450i Operator's Manual
43/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
Note At the completion of 2nd zero point return for a particular axis, thecorresponding lamps will start blinking.
One absolute type encoder is used on each axis of the machine;therefore, there is really no need to execute Zero Point Return after
powering on the machine.
These lights will not come on except for the execution of zero pointreturn, even if the machine reaches to its zero point
At the completion of 2nd zero point return, the corresponding lamp willblink.
2.3.4 Rapid Feed Override PushbuttonRapid Feed Override 0% Pushbutton (29)
Pressing this pushbutton, in any mode, cancels RapidSpeed Override on any of the 4 axes.
Rapid Feed Override 8% Pushbutton (30)
In any mode, the selection of the Rapid Speed Override of8% on any of the 4 axes can be made by pressing this
pushbutton.
Rapid Feed Override 15% Pushbutton (31)
43
7/30/2019 MB0120120108 HS-450i Operator's Manual
44/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
In any mode, the selection of the Rapid Speed Override of
15% on any of the 4 axes can be made by pressing thispushbutton.
Rapid Feed Override 25% Pushbutton (32)
In any mode, the selection of the Rapid Speed Override of25% on any of the 4 axes can be made by pressing this
pushbutton.
Rapid Feed Override 50% Pushbutton (33)
In any mode, the selection of the Rapid Speed Override of50% on any of the 4 axes can be made by pressing this
pushbutton.
Rapid Feed Override 100% Pushbutton (34)
In any mode, the selection of the Rapid Speed Override of
100% on any of the 4 axes can be made by pressing thispushbutton.
Note Cutting/JOG Feed Override Switch (62) is not available for Rapid Feed
Override.
44
7/30/2019 MB0120120108 HS-450i Operator's Manual
45/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
2.3.5 Coolant ON/OFF PushbuttonCutting Coolant Pushbutton (37)
Shower Coolant Pushbutton (38)Through Spindle Coolant Pushbutton (39)
Flood Coolant Pushbutton (40)
When any of these pushbuttons is pressed, its light comes onand its corresponding coolant pump is turned on. Subsequent
press of the same pushbutton turns off its coolant pump andlight.
These coolant pushbuttons are in effect regardless of mode
selection. It is therefore possible to turn off and on the flowof coolant during machining process in any mode.
During AUTO, MDI, or REMOTE mode, coolant can also be turned on and offby using M-codes.
Cutting Coolant
M08 cutting coolant starts
M09 cutting coolant stops, oil mist/air blow stops
Shower Coolant
M10 shower coolant startsM11 shower coolant stops
Spindle Through Coolant
M13 spindle through coolant starts
45
7/30/2019 MB0120120108 HS-450i Operator's Manual
46/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
M14 spindle through coolant stops
Flood Coolant
M15 flood coolant starts
M16 flood coolant stops
Note Shower coolant and flood coolant are automatically started when CycleStart pushbutton (56) is pressed.
Spindle through coolant is turned off when M6 or M106 is executed.
2.3.6 Spindle OperationSpindle Forward Rotation Pushbutton (41)
This pushbutton can only be used in JOG Mode. When it is
pressed, the spindle rotates clockwise. In any mode,whenever the spindle rotates forward, its lamp comes on.
Spindle Stop Pushbutton (42)
In HANDLE, JOG, RAPID or ZERO RETURN mode, when it ispressed, the spindle stops immediately.
Spindle Reverse Rotation Pushbutton (43)
This pushbutton can only be used in JOG Mode. When it is
46
7/30/2019 MB0120120108 HS-450i Operator's Manual
47/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
pressed, the spindle rotates counterclockwise. In any mode,whenever the spindle rotates in the reverse direction, its lamp
comes on.
Spindle Speed Decrease Pushbutton (44)
In any mode, each press of the pushbutton decreases the
spindle speed by 10% until the maximum deceleration, 50%,is reached.
Spindle Speed 100% Pushbutton (45)
By pressing this button, Spindle speed set by Spindle Speed
Deceleration pushbutton (44) or Spindle Speed Accelerationpushbutton (46) Spindle Speed is returned to its 100%.
Its lamp comes on, when this pushbutton is pressed.
Spindle Speed Increase Pushbutton (46)
In any mode, each press of the pushbutton increases thespindle speed by 10% until the maximum acceleration, 150%,
is reached.
2.3.7 B-axis Table Clamp/UnclampB-axis Table Clamp and B-axis Table Unclamp operations can only be donein JOG mode.
B-axis Table Unclamp Pushbutton (47)
47
7/30/2019 MB0120120108 HS-450i Operator's Manual
48/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
In JOG mode, pressing this button causes B-axis Table to be
unclamped. Its lamp comes on when B-axis Table isunclamped.
Note The B-axis Table can only be turned when it is unclamped.
B-axis Table Clamp Pushbutton (48)
In JOG mode, pressing this button causes B-axis Table to beclamped. Its lamp comes on when B-axis Table is clamped.
When clamped, the B-axis Table cannot be turned.
2.3.8 Chip Auger PushbuttonChip Auger Forward Pushbutton (63) (Option)
This pushbutton is used to turn Chip Auger so that it moves
the chips in the forward direction.
Chip Auger Stop Pushbutton (64) (Option)
This pushbutton is used to stop Chip Auger immediately.
Chip Auger Reverse Pushbutton (65) (Option)
This pushbutton is used to turn Chip Auger so that it movesthe chips in the reverse direction.
48
7/30/2019 MB0120120108 HS-450i Operator's Manual
49/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
2.3.9 Miscellaneous PushbuttonsDoor Open Request Pushbutton (49)
Before opening Operator Side Door, its necessary to pressDoor Open Request Pushbutton (49). When pressed, the lampis lit and the safety lock of the door is released.
To lock Operator Side Door again, close the door completely.When the door is closed, the door will be locked automatically
and this buttons lamp will go off.
Auto Power off Pushbutton (50)
Auto Power OFF function can be enabled by pressing AutoPower Off pushbutton (50). If pressed, its lamp will come on.
With Auto Power OFF turned on, when an automatic operationends (M30), the machine goes into the emergency stop state,
NC is powered off, and finally the main switch is turned off.
Note Remember to release this pushbutton, once the main power is turnedback on.
Air Blow (51)
In Manual Mode, when this pushbutton is pressed, Air Blow
starts and its lamp comes on. Subsequent press of thispushbutton stops Air Blow and its lamp to go off.
In MDI Mode or AUTO Mode, press this pushbutton to stop Air
Blow if it has been turned on; or press this pushbutton to startAir Blow if it has not been turned on.
Note In MDI Mode or AUTO Mode, M09 command can be used to turn off AirBlow; and M07 command can be used to turn on Air Blow.
49
7/30/2019 MB0120120108 HS-450i Operator's Manual
50/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
Oil & Air System Lubrication Oil Pushbutton (52)
When this button is pressed, lubrication oil is supplied to
ballscrews, linear guides, and the spindle for 6 seconds.
Note When NC is in ready state for operation, any axial movement or
spindle rotation will trigger lubrication oil and air to be automaticallysupplied to ballscrews, linear guides, and the spindle. Air is
continuously supplied whenever NC is in its ready state.
Oil lubrication cycle repeats itself as described below:
1)Lubrication oil is supplied for 20 seconds.2)Lubrication stops for 6 minutes.The lubrication oil can manually be turned on by pressing thispushbutton. Each press of this pushbutton triggers the oil lubricant to
be dispensed to ballscrews, linear guides, and the spindle for 20seconds.
Work Light ON/OFF Pushbutton (53)
This pushbutton is used to turn on/off the work light.
Tool Display Pushbutton (54)
Press this pushbutton to navigate the LCD display to Tool
Data.
As an example, in OPERATOR MESSAGE section, the following
tool information are displayed:
SPINDLE TOOL NO. = 2
50
7/30/2019 MB0120120108 HS-450i Operator's Manual
51/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
WAITING POT TOOL NO. = 1MAGAZINE POT TOOL NO. = 0
The data are interpreted as below:
Tool #2 in the spindle.
Tool #1 in the waiting pot.There is no tool in the magazine pot.
Safety Both Hands Pushbutton (69)
This pushbutton is needed for safety reason. Pressing
Machine Lock pushbutton or Program Restart pushbutton isonly effective when this pushbutton is also pressed at the
same time.
51
7/30/2019 MB0120120108 HS-450i Operator's Manual
52/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
2.3.10 Cycle Start Pushbutton
By pressing Cycle Start Pushbutton (56), an operation in
AUTO or MDI mode is started.
When a program is being executed, the lamp of Cycle Start
pushbutton will come on and stay on. The lamp will go off,once the program execution is ended, when FEED HOLD is
executed, or when the program execution is stopped orsuspended.
In the following cases, Cycle Start pushbutton is ignored:
Emergency stop is in effect. Mode selection is incorrect. Sequence number search is executing. Any alarm is not yet cleared. The numerical control system is not ready ("NC READY" is not displayed
on LCD) APC or ATC unit has not yet returned to its home position.
2.3.11 Feed Hold Pushbutton
This Feed Hold Pushbutton (57) is used to stop an automaticoperation in AUTO or MDI mode.
When this button is pressed, the followings occur:
The Cycle Start lamp goes off and the Feed Hold lampcomes on.
All axial movements are decelerated and subsequentlystopped.
Dwell is suspended. For M and S functions, the machine stops after executing
the current command. In the tapping cycle or counter tapping cycle, the machine
stops when the cycle reaches its end although Feed Holdpushbuttons lamp remains lit.
52
7/30/2019 MB0120120108 HS-450i Operator's Manual
53/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
If Feed Hold pushbutton is pressed during the movement
between the point R and the initial point, the movement stopsimmediately.
While Feed Hold is in effect, spindle rotation and coolantsystem are not stopped; thus, manual operation is stillpermitted.
While an automatic operation is being suspended, if themachine is operated manually, the axial positions may
possibly be shifted. Therefore, before restarting automaticoperation, return the axes to their prior positions.
Note To restart the operation, press Cycle Start pushbutton.
MDI command is not available if the machine is suspended with FeedHold.
2.3.12 Emergency Stop Pushbutton
Emergency Stop Pushbutton (67) is used to stop the machineimmediately in case of emergency. Once this button ispressed, it remains latched in the STOP position. To releasethe button, turn it clockwise. When an emergency stop takes
place, the power to the motors is interrupted, and all axialmovements and spindle rotation are stopped.
Note Be sure to remove the cause of emergency stop before releasingEmergency Stop button.
After releasing this button, pressing NC Ready pushbutton repeatedly
until EMG message disappears.
When the operation is restarted, all commands for axial movement orspindle rotation before the Emergency Stop occurred are lost.
CAUTION All personnel must know the locations of all Emergency Stop
53
7/30/2019 MB0120120108 HS-450i Operator's Manual
54/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
buttons and how to use them in case of emergency.
2.3.13 Feed Rate Override SwitchThis Feed Rate Override and JOG Feed Override Switch (62) can be used forsetting the feed rate override in JOG mode.
An override from 0 to 200%, at an interval of 10%, can be
applied to the feed rate specified by the F function inautomatic operation (AUTO, MDI). Normally, it is set to
100%.
Note: When Feed Rate Override switch is set at 0, no axial movement is
permitted.
NC Ready Pushbutton (68)
With NC powered on or emergency stop released, press thisbutton causes NC to enter its ready state. The lamp will light
up when both numerical control and mechanical system areready for operation.
2.3.14 Memory Protect Switch
locked to the mode previously selected; none of mode
OP LOCK (Operation Lock), the mode is temporarilyregistration or editing is prohibited. If the switch is set to
memory is protected from any modification, consequently,
this switch is set to "M LOCK" (Maintenance Lock), theregistration and editing of a program is allowed. WhenWhen Memory Protect Switch (70) is set to "CANCEL",
54
7/30/2019 MB0120120108 HS-450i Operator's Manual
55/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
selection pushbutton is functional.
The table below lists the operations allowed or disallowed according to the
mode selected by the Memory Protect Switch.
Cancel 1Op Lock M Lock
Program Edit/Transfer Yes Yes No
Tool Offset Yes Yes No
Workpiece Coordinate Offset Yes Yes No
Macro Variables Yes Yes No
Tool Life Management Yes Yes No
Mode Switch Yes No YesAxial Movement Yes No Yes
Tool Search/Tool Exchange Yes No Yes
Spindle Rotation Yes No Yes
Program Execution Yes No Yes
Peripheral Motor Action Yes No Yes
Message Display No Yes No
1Op Lock When Memory Protect Switch is set to Op Lock, the operations
listed in the table above are allowed only if Keep Relay K0.6 is
set to 1.
CAUTION Be sure to set this switch to "M LOCK" or OP LOCK after editing
or registering a program in memory.
55
7/30/2019 MB0120120108 HS-450i Operator's Manual
56/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
2.3.15 Pallet Control and PushbuttonsPallet Manual Selection Switch (71)
This switch is only meaningful in JOG mode. When Pallet
Start pushbutton (73) is pressed, the operation selected bythis switch is performed.
Note This switch is functional only when the machine is in the APC ready
position.
Pallet Set-up Pushbutton (72)
After workpieces have been set up on the pallet, press thisbutton to indicate to the machine that the workpieces on the
pallet are ready. When this button is pressed, its lamp comeson and stays on. At this point, the pallet is in a set-up state
and is awaiting the pallet change operation to start. When the
pallet is in set-up state, the front set-up doors are locked.
In AUTO mode, if the pallet is not in set-up state, the palletswill not be exchanged per any APC command; instead, the
pallet change operation is suspended until this button ispressed.
If the pallet is in already set-up state, press this button again
will cancel its set-up state and its lamp also goes off.
When pallets are exchanging, the lamp of Pallet Set-Uppushbutton will blink until the pallet change operation iscompleted. Once the pallet change operation is completed,
the locks on the set-up doors are released.
CAUTION Do NOT open the set-up door whenever the lamp of Pallet
Set-Up pushbutton is blinking.
56
7/30/2019 MB0120120108 HS-450i Operator's Manual
57/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
Pallet Start Pushbutton (73)
In JOG mode, pressing this button will start the operation
selected by Pallet Manual Selection Switch (71). When itslamp is lit, manual operations of APC are allowed.
2.3.16 Pushbuttons of OptionsF1DT Pushbutton (94)
To be designed.
PLBK Pushbutton (95)
To be designed.
HINT Pushbutton (96)
To be designed.
5UNC Pushbutton (97)
To be designed.
JUNC Pushbutton (98)
57
7/30/2019 MB0120120108 HS-450i Operator's Manual
58/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
To be designed.
F2 Pushbutton (99)
Reserved for future feature.
2.3.17 Manual Pulse Generator
In HANDLE mode, Manual Pulse Generator (82) is used to
move the axes at finer steps.
On Manual Pulse Generator, feed of 0.001 mm or 0.001o(x1), 0.01 mm or 0.01o (x10), 0.1 mm or 0.1o (x100) perscale can be selected.
To operate, select axis and scale, and then turn the handle.
One rotation of the handle is equivalent of 100 scales.
Note The handle should not be turned more than five rotations per second.
58
7/30/2019 MB0120120108 HS-450i Operator's Manual
59/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
2.4 Other Controls and Pushbuttons2.4.1 Spindle Tool Clamp/Unclamp PushbuttonSpindle Tool Clamp/Unclamp Pushbutton (58)
This pushbutton is on the enclosure panel next to the operators side doorfor easy access.
In JOG mode, when the spindle tool is clamped, pressing thisbutton causes the spindle tool to be unclamped. Similarly,
when the spindle tool is unclamped, pressing this buttoncauses the spindle tool to be clamped.
The lamp comes on when the spindle tool is in the unclampedstate.
Note Be sure to hold the tool by hand before unclamping it.
Press and hold the button for at least one second. If not, Spindle ToolClamp/Unclamp may not function properly.
The spindle tool cannot be unclamped while the spindle is rotating.
When the spindle is unclamping, it will clamp the tool if the hydraulicpressure suddenly drops because of either emergency stop or power-off.
If spindle rotation or spindle orientation is commanded while spindle
tool is unclamped, the machine will enter Feed Hold state.
The command for spindle rotation or spindle orientation should only be
submitted for execution when the spindle tool is clamped.
59
7/30/2019 MB0120120108 HS-450i Operator's Manual
60/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
2.4.2 Pallet Setting Side
Pallet Set-up Pushbutton (80)
Same function as Pallet Set-up pushbutton (72) on the
Emergency Stop Pushbutton (81)
Same function as Emergency Stop pushbutton (67) on the
80 81
machine operation panel. Refer to Section 2.3.15.
machine operation panel. Refer to Section 2.3.12.
60
7/30/2019 MB0120120108 HS-450i Operator's Manual
61/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
2.4.3 ATC Magazine Side
Emergency Stop Pushbutton (75)
Same function as Emergency Stop pushbutton (67) on the
79
78
77
76
75
machine operation panel. Refer to Section 2.3.12.
61
7/30/2019 MB0120120108 HS-450i Operator's Manual
62/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
ATC Manual Operation Switch (76)
In JOG Mode, the movement in ATC can be selectedwith this switch, followed by pressing ATC Manual
Start Pushbutton to execute the selected ATCoperation.
There are limitations imposed on the actions of ATC that can beselected with ATC Manual Operation Select switch:
Movements in (white) are available only in JOG Mode and when thespindle is in tool change position.
Movements in (grey) are available in Automatic operation modeprovided that ATC magazine has not been stopped.
Double Arm Chucking
ATC Shutter Open
Tool Unclamp
Initial PositionDouble Arm to
Tool Clamp
Counter ClockwiseDouble Arm Turn 180
ATC Shutter Close
180 ClockwiseDouble Arm Turn
Counter Clockwise
Magazine Rotate
Arm Side
Tool Pot to Double
ClockwiseMagazine Rotate
Magazine SideTool Pot to
62
7/30/2019 MB0120120108 HS-450i Operator's Manual
63/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
ATC Manual Start Pushbutton (77)
Pressing this pushbutton causes the operation selected by
the ATC Manual Operation Switch to be started rightaway.
Note Make sure the door of ATC magazine is closed before pressingATC Manual Start pushbutton.
Single Arm Manual Operation Switch (78)
In JOG mode, a Single Arm manual operation can
be selected with this switch, followed by pressingSingle Arm Manual Start pushbutton (79) to start
the operation.
Note Manual continuous operation can be started in any operation
mode.
Continuous Operation
Tool from Waiting pot to Magazine pot
Tool from Magazine pot to Waiting pot
63
7/30/2019 MB0120120108 HS-450i Operator's Manual
64/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
Single Operation
Tool chucking at Magazine pot
Tool chucking at Waiting pot
Grippers locked and Tool removed
Single arm from Magazine pot to Waiting pot
Single arm from Waiting pot to Magazine pot
Tool inserted and Grippers unlocked
Single arm to the initial position
64
7/30/2019 MB0120120108 HS-450i Operator's Manual
65/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
Single Arm Manual Start Pushbutton (79)
The operation that is currently selected by the Single Arm
Manual Operation Switch can be started by pressing thisbutton.
Note After the machine is powered on, make sure there is adequatehydraulic pressure before manually operating the single arm.
65
7/30/2019 MB0120120108 HS-450i Operator's Manual
66/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
3 Starting and Ending OperationBefore starting any operation, check the machine to ensure all safety
regulations are enforced. (Refer to Safety Precautions)
3.1 Emergency StopEmergency Stop is used to stop the machine operation immediately.
Emergency Stop is used to stop the machine operation
immediately in case of emergency. There are three
3.2 Turning ON PowerFollow the procedure below to turn on the machine:
Make sure factory power is supplied to the electric cabinet.
Turn on Main Power switch on the electric cabinet.
Power Lamp on the electric cabinet comes on. Ventilation fans in the electric cabinet are turned on. Spindle motor fan is turned on.
Release all Emergency Stop pushbuttons (67), (75), and (81).
Emergency Stop buttons (67), (75), and (81). Thesebuttons are effective in any mode.
66
7/30/2019 MB0120120108 HS-450i Operator's Manual
67/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
Press NC Power ON pushbutton (0)
The lamp of NC Power ON pushbutton lights up. The LCD displays System Configuration screen and NC is
now powered.
Press NC Ready pushbutton (68) and hold for a few seconds.
The lamp of NC Ready pushbutton lights up. The machine is now ready for operation.
Items to check after the machine is powered on are:
Items Check ForMotors Abnormal heat or noise
LCD screen Alarm display
3.3 Machine Warm-upMachine warm-up is mandatory in order to ensure smooth and properoperations of every component of the machine, and to minimize the effect of
heat expansion on the machine accuracy.
Lubrication
After the machine is powered on, oil is automatically supplied to spindle,ballscrews, and linear guides, etc., where lubrication are needed.
However, immediately after the machine is turned on, the spindle bearings
are not sufficiently lubricated. In order to ensure that these parts are notdamaged unintentionally, the following rules must be strictly enforced:
If the machine has been turned off for less than 48 hours, do NOT turnthe spindle for at least 20 minutes after the machine is powered on.
If the machine has been turned off for more than 48 hours, do NOT turnthe spindle for at least 40 minutes after the machine is powered on.
Air unit Adequate air pressure (0.6 MPa)
67
7/30/2019 MB0120120108 HS-450i Operator's Manual
68/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
CAUTION Spindle can be damaged if it is rotated before its spindle
bearings are adequately lubricated.
Hydraulic Circuit
To warm up of the oil in the hydraulic circuit, use the following two Mfunctions to increase the oil temperature:
M83 - When room temperature is in the range of 5C~15C(40F~60F).
M84 - When room temperature is less than 5C (40F)Note The oil in the hydraulic circuit, when it is cold, has high viscosity which
can cause problems in certain operations, such as spindle tool
clamp/unclamp.
Grease
Grease also needs to be warmed up so that it can permeate the parts and
the components. For example, insufficient lubrication on the clamp pins ofthe double arm may result in a tool chucking problem.
Warm-up Procedure without using Weekly Timer
Two warm-up programs, O8930 and O8931, are installed on the machine
before delivery. The elapsed time since the last power-off of the machinecan be used to determine which one of the two programs to execute.
If the machine has been powered off for more than 48 hours, execute warm-
up program O8931. If the machine has been powered off for less than 48
hours, execute warm-up program O8930.
The execution time for O8930 is approximately 50 minutes. The executiontime for O8931 is approximately 60 minutes.
68
7/30/2019 MB0120120108 HS-450i Operator's Manual
69/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
3.4 Turning OFF Power
Make sure that the light of Cycle Start pushbutton (56) is off.
If the light of Cycle Start pushbutton is not off, press FeedHold pushbutton (57).
Press Emergency Stop pushbutton (67).
Press NC Power OFF pushbutton (00).
Turn off Main Power switch.
3.5 After Turning Off PowerAny cleanup work should only be carried out after the machine has beenturned off.
DANGER Be sure to turn off all power supply to the machine and to thedevices such as chip conveyor before cleaning them.
Chips are flushed by coolant toward the chip pan sitting at the front ofthe machine. Make sure that chips are not over-accumulated in the chip
pan. Chips left on the covers should be brushed off with soft brushes. Do NOT use air gun to blow chips away from the covers.
69
7/30/2019 MB0120120108 HS-450i Operator's Manual
70/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
Remove chips and wipe clean coolant left on the covers. Coolant andchips infiltrate underneath the covers can potentially damage machinecomponents such as spindle bearings or ballscrews.
Always wear gloves to clean chip debris. Be aware that solenoid valves will remain hot after the machine is
powered off. Refrain from touching them for a while. If the machine will not be operated for a long time, insert a tool into the
spindle to prevent foreign matters from entering.
3.6 Measures in Power FailureWhen power failure occurs during machine operation, the NC unit and theelectrical control units are all powered off; the machine goes into the
emergency stop state. As a result, the commands stored in the NC buffer orinput through the operation panel are cleared and lost.
Below are the steps to take immediately following a power failure:
Press Emergency Stop pushbutton (67).
Turn off Main Power switch.
Below are the steps to take after power is restored:
Turn on Main Power switch on the electric cabinet. Refer to
Release all Emergency Stop pushbuttons (67), (75), and
(81).
Section 3.2 Turning ON Power.
70
7/30/2019 MB0120120108 HS-450i Operator's Manual
71/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
Press NC Power ON pushbutton (0)
Press NC Ready pushbutton (68) and hold for a few seconds.
Troubleshoot and remove the causes of alarms if any.
Restore the machine, with manual operations, to theconditions before power failure.
WARNING Corrective actions after power is restored must be carried outwith manual operations. This is because the remaining
pneumatic/hydraulic motion may be continued unexpectedly
when these circuits are turned back on.
After power to the machine is restored, the states of the machine should beas follows:
Before Power Failure After Power is Restored
Spindle tool clamped Spindle tool clampedSpindle tool unclamped Spindle tool unclamped
Spindle rotating Spindle stoppedSpindle stopped Spindle stopped
X/Y/Z/B axis feed Unchanged
ATC motion Stopped/UnchangedAPC motion Stopped/Unchanged
71
7/30/2019 MB0120120108 HS-450i Operator's Manual
72/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
3.7 Weekly TimerThis machine is equipped with a weekly timer. This weekly timer can be
enabled or disabled by the key switch located on the door of the electriccabinet.
By using the weekly timer, the machine can be automatically turned on and
off at preset times.
If the weekly timer is used to turn on the machine, warm-up programs ofthe spindle and other movable components will be automatically performed.
ON Operation
1)At the preset ON time, AC power is supplied to the power supply moduleof the machine.2)NC is turned on.
3)The machine gets in the Ready state for operation. (All emergency stopbuttons must be released.)
4)Twenty minutes later, a spindle warm-up program (installed at factory) isstarted. It will take about 25 minutes to warm-up the 15,000 rev/minspindle.
5)When the spindle warm-up is finished, the machine warm-up program willbe started.
Note The key switch for the weekly timer must be set to ON (enabled) and
the day selection switch for that day is set to ON.
OFF Operation
1)At the preset OFF time, the machine goes into the emergency stop state.Note If a program is being executed at preset OFF time, the machine will
wait until the program complete its execution before entering the
emergency stop state.
2)NC is turned off.3)AC power supply to the power supply module is shut off, but the main
power switch stays ON.
Prepare Weekly Timer for Next Day
72
7/30/2019 MB0120120108 HS-450i Operator's Manual
73/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
Check the following items before the Weekly Timer turns off the machine:
The weekly timer is correctly set for the next operation day. All emergency stop buttons are released. AUTO Mode is selected. Single block switch on the operation panel is set to OFF. Make sure that no tool is in the spindle. This is important because if
there is a tool in the spindle, it may cause problems during the nextautomatic spindle warm-up procedure.
There is no tool or part unintentionally left in the machining area. All machine doors are closed (Door Open Request pushbutton is OFF). Feed rate override switch/pushbutton is set appropriately. The waiting pot is positioned at the spindle side (normal position), The main power switch is set to ON.Note Do not use the Auto Power Off function. Auto Power Off causes the
main power switch to be turned off.
The key switch for the weekly timer must be set to ON (enabled).
73
7/30/2019 MB0120120108 HS-450i Operator's Manual
74/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
4 Manual Operation4.1 Zero Point Return
In this machine, every axis is equipped with an absolute type encoder fortracking its positions. Therefore, it is not required that the zero point return
be executed after the machine is powered on. However, if any servo motorloses its zero point data because of low battery, executing the zero point
return will become necessary for all axes.
The zero point return procedure for B-axis is slightly different from that of X,
Y, or Z axis.
For X, Y, and Z axes, please refers to Section 11.6 Zero Point Setting ofAxes in HS-450i Maintenance Manual.
For B axis,
Press Zero Point Return Mode pushbutton (8).Its lamp comes on.
Select an appropriate rapid feed rate with one of
Rapid Feed Override pushbuttons, 8%, 15%, 25%, 50%,
Press and hold B-axis Plus Direction Feed and Zero ReturnPushbutton (27) until its completion lamp is lit which
indicates that B-axis has reached its zero reference point.
or 100% (30) to (34).
74
7/30/2019 MB0120120108 HS-450i Operator's Manual
75/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
When over-travel fault occurs, follow the steps outlined below to resolve the
error:
1)Move every axis to the center of its travel path by manual operation.2)Press the NC Power OFF pushbutton (00).3)While pressing [P
7/30/2019 MB0120120108 HS-450i Operator's Manual
76/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
Note Over-travel alarm is triggered whenever any axis travels past its
over-travel limits. Axis itself cannot travel past its travel limits ineither automatic mode or manual mode.
To resolve Over-travel alarm, move the axis in the opposite direction
in manual operation, and then press RESET button.
4.3 Rapid TraverseRapid traverse is to move each axis continuously at a rapid traverse rate.Override of 0, 25, 50 and 100% can be selected.
In any mode, the selection of the Rapid Speed Override of
0%, 8%, 15%, 25%, 50% and 100% on any of the 4 axescan be made by pressing the corresponding pushbutton.
Press RAPID Mode pushbutton (7) to put the Machine inRAPID Traverse mode. Its lamp will be lit.
RAPID Mode
Select the desired rapid feed speed of 0%, 8%, 15%, 25%,
50% and 100% by pressing one of the Rapid Feed Overridepushbuttons, (29) to (34).
Press one of the Plus Direction Feed and Zero Return
Pushbutton, (21), (23), (25) or (27), to move the selectedaxis in the positive direction.
Or press one of the Plus Direction Feed pushbuttons (22),
76
7/30/2019 MB0120120108 HS-450i Operator's Manual
77/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
(24), (26), or (28), to move the selected axis in the negativedirection.
When one of these pushbuttons is pressed, the selected axis
moves continuously at the rapid traverse rate selected in the
previous step.
4.4 Handle FeedHandle feed is to move each axis little by little using the Manual Pulse
Generator (82). On Manual Pulse Generator (82), feed rate of 0.1, 0.01, or
0.001 mm/scale is available for X, Y and Z axes, while 0.1, 0.01, or 0.001per scale is available for B axis.
Each revolution of the dial equals 100 scales. The dial should only be turned
at a speed less than 5 revolutions per second.
Press HANDLE Mode pushbutton (5) to enter Handle
mode. Its lamp will be lit.
Select 1 (0.001mm), 10 (0.01mm), or 100 (0.1mm)
using the Handle Feed Selection switch on Manual PulseGenerator (82).
Select an axis to move with the Axis Selection switch onManual Pulse Generator (82).
Whilst the pushbuttons (21), (23), (25), and (27) on
Operation Panel are functional in HANDLE mode, the lamp
of the selected axis using Axis Selection Switch will be lit.
Turn the handle of Manual Pulse Generator (82) to movethe selected axis.
The amount of movement is calculated according to the
number of turns and the selected handle feed rate.
77
7/30/2019 MB0120120108 HS-450i Operator's Manual
78/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
Note Manual Pulse Generator is only used in HANDLE Mode.
4.5 Insertion/Removal of Spindle ToolTo insert a tool into the spindle or to remove a tool from the spindle, followthe steps below:
1) Move spindle head toward the operator side using handle feed.2) Press Door Open Request button (49) to open the door.3) Press JOG Mode pushbutton to enter JOG mode.
Tool Removal
While holding the spindle tool firmly by hand, press Spindle
Tool Insertion
Insert a tool into the spindle, then press Spindle ToolClamp/Unclamp button (58) again. The tool is clamped in the
spindle and the lamp of Spindle Tool Clamp/Unclamp buttonwill go off to indicate as such.
Note Be sure to hold the spindle tool firmly by hand before pressing thisbutton to unclamp it.
When pressing the button, keep it pressed securely for at least onesecond. If not, this button may not function correctly.
and can be removed from the spindle.Tool Clamp/Unclamp button (58). The tool will be unclamped
Press Spindle Tool Clamp/Unclamp button (58). The lamp
position.
will come on indicating that the spindle is in an Unclamp
78
7/30/2019 MB0120120108 HS-450i Operator's Manual
79/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
When the spindle is in the unclamp state, it does not execute spindlerotation or spindle orientation command.
WARNING Do not touch the cutting edge of tools by hand. Be sure to stayaway from a rotating spindle.
4.6 Spindle Revolution and Stop
Press JOG Mode pushbutton (6) to enter JOG mode. Its lampwill be lit.
Press Spindle CW Rotation pushbutton (41) to rotate thespindle clockwise, or press Spindle CCW Rotation pushbutton(43) to rotate the spindle counter-clockwise.
When Spindle CW Rotation pushbutton (41) or Spindle CCW
Rotation pushbutton (43) is pressed, the spindle rotates atthe speed specified in the "S" command that was executed
previously in MDI or AUTO mode.
If not a single MDI or AUTO operation has been executed
since the machine was powered on, the spindle will not rotate
because the spindle speed is undetermined.
To resolve this, execute a spindle speed command in MDI
mode before issuing any spindle rotation command.
To change spindle speed, the speed override of 50% to 150%
can be achieved using Spindle Speed Decrease pushbutton(44) or Spindle Speed Increase pushbutton (46).
Press Spindle Stop pushbutton (42) to stop the spindlerotation.
Note Spindle Stop pushbutton (42) is only functional in HANDLE, RAPID, or
JOG mode.
79
7/30/2019 MB0120120108 HS-450i Operator's Manual
80/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
5 MDI Operation5.1 MDI (Manual Data Input) Operation
In MDI mode, commands can be entered into MDI operation buffermemory through LCD/MDI panel.
Press MDI Mode pushbutton (4) to enter MDI mode. Thelamp of MDI Mode pushbutton comes on and MDI screen
is displayed on the LCD.
If any other screen is displayed, press [PROG] key or MDIsoft key to navigate the display to MDI screen.
Enter a block of commands and then press [EOB] key,followed by [INSERT] key.
Move the cursor to the top of the program or to theposition where the program should start.
Program starts from the top of block where the cursor is.
Press Cycle Start pushbutton (56).
Note On the LCD screen, one page of program, up to 10 blocks, canbe executed in the same manner as the normal program.
While a program is being executed, to stop execution of the
program immediately, press Feed Hold pushbutton (57).
Program No. "O0000" is automatically added at the top of theprogram created in MDI mode.
To clear the program created on the LCD, input "O" then press[DELETE] key. By parameter setting, [RESET] key can clear the
program.
PROG
EOB INSERT
80
7/30/2019 MB0120120108 HS-450i Operator's Manual
81/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
For the first time the program is executed, it will start from thetop of the block regardless of the cursor position. After the first
run, however, it will start from wherever the cursor is.
A program created in MDI mode can call sub-programs, but not
macro programs.
MDI operation is allowed only if there is enough memory to storethe program.
A MDI program is automatically deleted after the program
execution reaches %. However, a MDI program is not deletedif it includes M02, M30 or M99 in the program.
A MDI program in the memory is deleted under the following
situations:
EDIT Mode pushbutton (1) is pressed Background editing is completed Automatic operation is started.
5.2 Spindle Revolution in MDI
Press MDI Mode pushbutton (4) to enter MDI mode. The
lamp of MDI Mode pushbutton will come on.
Press [PROG] key on NC keyboard.
To specify the spindle speed in the command, key in S,followed by the desired spindle speed, then press[INSERT] Key.
To request for spindle rotation in the command, key inM03 (Forward) or "M04" (Reverse), and [EOB], then[INSERT].
For example: To rotate the spindle at 900 rpm forward,
enter:
PROG
81
7/30/2019 MB0120120108 HS-450i Operator's Manual
82/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
[S][9][0][0][INSERT]
[M][0][3][EOB][INSERT]Press Cycle Start pushbutton (56). As a result of the
execution of the commands entered previously, thespindle will rotate at the specified speed in the specified
direction.
Note During ATC operations or when the spindle tool is unclamped,Spindle Revolution command is ignored.
5.3 Spindle Orientation in MDI
Press MDI Mode pushbutton (4) to enter MDI mode. Thelamp of MDI Mode pushbutton will come on.
Press [PROG] key on NC keyboard.
Key in "M19" (orientation), [EOB], and[INSERT]
Press Cycle Start pushbutton (56).
Note Spindle Orientation does not get executed when the spindle isunclamped.
Spindles orientation is released when any ATC movement iscompleted and a Spindle Revolution command is executed.
PROG
M
SP
1 9
EOB INSERT
82
7/30/2019 MB0120120108 HS-450i Operator's Manual
83/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
5.4 ATC Magazine Indexing and Tool
Press MDI Mode pushbutton (4) to enter MDI mode. The
lamp of MDI Mode pushbutton will come on.
Registration for instructions.
Press [PROG] key on NC keyboard.
Key in the tool No. to be indexed.
For example, to index tool No. 1, press [T] [0] [1] [EOB][INSERT].
Press Cycle Start pushbutton (56). The tool is nowindexed at ATC position.
For ATC, move spindle head to ATC position.
Key in [M] [6] [EOB] [INSERT].
Press Cycle Start pushbutton (56). The spindle tool isexchanged with the indexed tool.
Note T** commands and M6 must be executed in different blocks.
PROG
INSERTEOB
1
SP
M
%
T
6
EOB INSERT
0
To register tools, please refer to Section 7.2 "Tool
(Refer to Section 7.4 "Tool Exchange in MDI Operation.)
83
7/30/2019 MB0120120108 HS-450i Operator's Manual
84/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
5.5 Table Clamp/Unclamp in MDI OperationIn MDI operation, M61 can be used to command the B-axis to be clamped,
while M62 and M63 can be used to command the B-axis to be unclamped.
M61
This is the only command to can be used for B-axis clamping.
M62
When M62 is executed in MDI mode, B-axis rotary table will be unclamped;it will be automatically clamped again once B-axis completes the rotation.
This Auto-clamp function in AUTO/REMOTE mode works the same way as in
MDI mode.
Note If B axis is stopped by Feed Hold, it will remain unclamped.
M63
M63 is a single command for B-axis unclamping. M63 doesn't executeAuto-clamp function after B-axis completes its rotation.
After M63 command is executed, M61 needs to be executed in order to
clamp the B-axis. M62 can be used to clamp the B-axis if it is executed inthe same block as the table rotation command.
Note Even if the table is unclamped by M63, machining process can still
continue, although, with inferior precision. For heavy cutting or
cutting accurate, make sure the table is clamped.
Note In Handle mode, when Manual Pulse Generators axis selection is setto 4, pressing either B-axis Plus Feed Zero Return Pushbutton or B-
axis Minus Feed pushbutton (28) causes B-axis to be unclamped.
When B axis is in the unclamped state, switching into Auto mode orMDI mode will cause B-axis to be clamped again, however, switching
into JOG mode or Zero Return mode, B-axis will remain unclamped.
84
7/30/2019 MB0120120108 HS-450i Operator's Manual
85/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
6 Automatic OperationBefore entering automatic operation
Check that the program is correctly entered. Check that all switches and pushbuttons are correctly set. Check that all doors are closed and that all covers are properly set. Check that no part of human body is and will be in the machine
movable area. Check that no interference is and will be introduced between tools and
workpieces or fixtures. Be sure to avoid any possibility of catching fire.
During automatic operation
Never open any door or any cover. Be sure that someone is ready to press Emergency stop pushbuttons
in case of an emergency.
After automatic operation
Before opening any door or any cover, check to make sure that theautomatic operation has stopped, and that all movements have
completely stopped.
Alarms
If an alarm appears and the machine has stopped, be sure to removethe cause of the alarm before restarting the operation. Failure to reactto these warnings may result in serious bodily injury to personnel or
serious damage to the machine.
85
7/30/2019 MB0120120108 HS-450i Operator's Manual
86/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
6.1 Starting Automatic OperationMemory Operation (AUTO)
Press AUTO Mode pushbutton (2). Its lamp should comeon.Press [PROG] key on NC keyboard.
The program edit screen will be displayed on the LCD.
Invoke a program with the following steps:
1. Press address key [O].2. Key in the program number with numerical keys. For
example, press [0], [1], [3] and [2] or just [1], [3]
and [2] for Program No. 0132.3. Press DOWN cursor key. The program will be
displayed on the LCD.4. Press [RESET] key.Check that the program is correctly entered, and then
press Cycle Start pushbutton (56) to execute theprogram.
Its lamp is lit and the program is executed.
Remote Mode Operation
Setup a tape reader or a program transfer device using theRS232C interface so that program can be retrieved from these
devices.
Press REMOTE Mode pushbutton (3) to enter Remote mode.
Its lamp should be lit.
Press Cycle Start pushbutton (56). Its lamp is lit. The
program is retrieved from the external device and thenexecuted, although its blocks are not displayed on the LCD
screen.
PROG
1O)
3 2
RESET
86
7/30/2019 MB0120120108 HS-450i Operator's Manual
87/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
6.2 Stopping & Restarting Automatic
Feed Hold (Halt)
Feed Hold pushbutton (57) is used to put the operation on atemporary stop.
Feed Hold lamp lights up and the lamp of Cycle Startpushbutton (56) goes off.
All movements are stopped. The dwell execution is halted. Immediately after the execution of M code or S code
commands is completed, the machine stops.
Feed Hold does not stop the spindle or coolant.
Single Block Stop
Single Block pushbutton (9) is used to execute one block of
program at a time. Press Single Block pushbutton causes itslamp to come on.
When an operation stops, the lamp of Cycle Startpushbutton (56) goes off.
With this pushbutton (9) ON, each press of Cycle Startpushbutton (56) executes the next one block and stops theoperation.
Suspension of Automatic Operation
Manual operation is allowed if automatic operation is stoppedby Feed Hold.
87
7/30/2019 MB0120120108 HS-450i Operator's Manual
88/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
MDI operation is allowed if automatic operation is stopped bySingle block.
Restart of Automatic Operation
Press AUTO Mode pushbutton (2) to put the machine back inautomatic mode.
Press Cycle Start pushbutton (56).
88
7/30/2019 MB0120120108 HS-450i Operator's Manual
89/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
6.3 Door Safety InterlockOperator Side Door
The operator side door has built-in safety lock.
Open the Door
To open this door during automatic operation,
Press Single Block Pushbutton (9). The lamp of Cycle Start
pushbutton should go off.
Press Door Open Request Pushbutton (63). Its lamp comeson.
The door can now be opened.
Note Pressing Door Open Request causes the spindle to stop, if it was
running, and the coolant pumps to stop pumping.
It may take a while before the spindle stops completely. The door canonly be opened after the spindle has completely stopped.
To Restart the Operation
Close the door. The lamp of Door Open Request should go
off. The door is locked.
In Auto mode, press Cycle Start Pushbutton (56).
The spindle and the coolant systems are restarted.
Press Cycle Start Pushbutton (56) again.
The program resumes from where it was stopped.
89
7/30/2019 MB0120120108 HS-450i Operator's Manual
90/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
Note The safety lock is fully engaged and functional even if the main power
switch is off.
The spindle restart is cancelled if RESET button is pressed, EmergencyStop button is pressed, or the power is turned off.
ATC Magazine Door
The ATC magazine door is equipped with a safety lock. The door cannot beopened when
ATCs double arm or single arm is in motion. The tool pot magazine is rotating.Unlike to open the operator side door, pressing Door Open Request
pushbutton is not needed in order to open the ATC magazine door.
Note When this door is open, no operation of ATC double arm, ATC singlearm, or tool pot magazine is permitted.
The safety lock is fully engaged and functional even if the main power
switch is off.
Set-up Doors
The set-up doors of this machine are equipped with safety locks.
These doors are locked when:
Pallet change operation is in process. The lamps of Pallet Set-up pushbuttons (72) and (80) are lit.Note In Auto mode or Manual mode, pallet change is allowed even if the
set-up doors are open or not locked. However, it is advised that pallet
change operation only be done with these doors closed.
The safety lock is fully engaged and functional even if the main power
switch is off.
90
7/30/2019 MB0120120108 HS-450i Operator's Manual
91/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
Summary of Door Interlocks
When Operator door is open
MODE
ACTION Auto and MDI Handle/Jog/Rapid/Zero Return
Axis Movement No Yes
Spindle Revolution No No
Tool clamp/unclamp No Yes
ATC Double arm No No
Tool magazine No Yes
APC Pallet change No No
Pallet clamp/unclamp No Yes
When ATC magazine door is open
ACTION Auto and MDI
Axis Movement Yes
Spindle Revolution Yes
Tool clamp/unclamp Yes
ATC Double arm No
Tool magazine No
APC Pallet change YesPallet clamp/unclamp Yes
When Set-up doors are open
ACTION All Modes
Axis Movement Yes
Spindle Revolution Yes
Tool clamp/unclamp Yes
ATC Double arm YesTool magazine Yes
APC Pallet change No
Pallet clamp/unclamp Yes
91
7/30/2019 MB0120120108 HS-450i Operator's Manual
92/152
HS-450i Operator's Manual
AVEREX Automation Co., Ltd.
7 ATC Operation7.1 Setting up ATC MagazineInserting tools into the tool pots or removing tools from the tool pots
can be done using ATC Man