INSTRUCTION for TSD-M… Torque Screwdrivers

TSD-M 1,2NM

Tool bits for slotted-head, Phillips, and test socket screws.

TSD-M 6NM

TSD-M 3NM

1 / Maria Schierscher/ M&I-TSD/May 2012

INSTRUCTIONS for TSD-M… Torque Screwdrivers

Features•Phoenix Contact‘s new constant torque screw driver enables a much faster and more reliable connection for their screw terminal block line. •The TSD-M can be easily equipped with standard bits and the quick-exchange holder allows for fast bit exchange. •The required torque is adjustable in small increments, according to EN ISO 6789.•Non-slip 2 component handles provide for maximum grip.

2 / Maria Schierscher/ M&I-TSD/May 2012

INSTRUCTIONS for TSD-MTorque setting:•Push down the adjustment ring while turning it simultaneously. Tool required for TSD-M 6NM.•Each 180 rotation changes the torque and distinct feedback signals when the adjustment ring engages.•Clockwise rotation increases the torque value and counterclockwise rotation decreases it.

The tool can be found and stored in the base of the handle.

TSD-M 6NM

3 / Maria Schierscher/ M&I-TSD/May 2012

INSTRUCTIONS for TSD-M

Reading the torque:•You can read the set torque from the scale to the right or left of the arrow tip. Example is set at 1.05.•The torque level is set in order to prevent an over or under-torque that could potentially cause problems with the connections.

4 / Maria Schierscher/ M&I-TSD/May 2012

INSTRUCTIONS for TSD-M

Inserting a bit:

Push the bit into the quick-exchange holder until it snaps into place audibly.

5 / Maria Schierscher/ M&I-TSD/May 2012

INSTRUCTIONS for TSD-M

Removing a bit:

Push the sleeve forward and remove the bit.

6 / Maria Schierscher/ M&I-TSD/May 2012

INSTRUCTIONS for TSD-M

Tightening screws:•The free-running sleeve provides additional grip when using the screwdriver and helps you to stabilize the screwdriver.•When the set torque has been reached, the screwdriver releases mechanically and provides both audible and distinct feedback to the operator.•It is not possible to tighten the screw further.

7 / Maria Schierscher/ M&I-TSD/May 2012

INSTRUCTIONS for TSD-M

Loosening screws:

To enable you to loosen tight screws the torque for loosening screws is not limited, meaning it functions like a normal screwdriver.

8 / Maria Schierscher/ M&I-TSD/May 2012

INSTRUCTIONS for TSD-M

Suitable bits:

The quick-exchange holder accepts ¼” bits.

9 / Maria Schierscher/ M&I-TSD/May 2012

INSTRUCTIONS for TSD-MTorque Matrix

TSD-M 1.2 NM

p/n 1212224

0.3-1.2 NM 5.2 mm

6.2 mm

UT 2.5

UT 4

0.6-0.8 NM

0.6-0.8 NM

TSD-M 3 NM

p/n 1212225

1.2-3.0 NM 8.2 mm

10.2 mm

12.2 mm

UT 6

UT 10

UT 16

1.5-1.8 NM

1.5-1.8 NM

2.5-3.0 NM

TSD-M 6 NM

p/n 1212226

3.0-6.0 NM

16 mm

UT 16

UT 35

2.5-3.0 NM

3.2-3.7 NM

TSDTorque Range

UT Terminal block

Terminal block torque

required

*NOTE: if the torque screwdriver will not be used for a longer period, set the adjustment ring to the lowest torque value. This relieves the spring mechanism. *NOTE: Do not exceed maximum torque level as this may cause damage to the screwdriver or the material and the precision cannot be guaranteed.

Width

10 / Maria Schierscher/ M&I-TSD/May 2012

INSTALLATION – TSD-MTool bits

Descriptionthickness x width x

height in mm

thickness x width x height in inches

Part number

Slotted-head

screws

ASD BIT 0,5X3,0X50 .01969 x .11811 x 1.96850 1212566

ASD BIT 0,6X3,5X50 .02362 x.13780 x 1.96850 1212568

ASD BIT 0,6X3,5X70 .02362 x .13780 x 2.75591 1212569

ASD BIT 0,8X4,0X50 .03150 x .15748 x 1.96850 1212571

ASD BIT 1,0X5,5X50 .03937 x .21654 x 1.96850 1212574

Graded, for test socket

screws

SF-BIT-SLS 0,9X6,5-50 .03543 x .25591 x 1.96850 1212606

SF-BIT-SLD 0,6X3,5-50 .02362 x .13780 x 1.96850 1212605

Phillips screws

SF-BIT-PH 1-50 Phillips #1 x 2 in 1212579

SF-BIT-PH 2-50 Phillips #2 x 2 in 1212580

SF-BIT-PH 2-70 Phillips #2 x 2.75 in 1212583

11 / Maria Schierscher/ M&I-TSD/May 2012