© 2010 Martha Stewart Living Omnimedia, Inc. All rights reserved. For personal use only, not for commercial use.

Clip Art: “Fine Specimens” Wings Aflutter Large Perched Red Butterflyfrom Martha Stewart Living | www.marthastewart.com

How-to:Each wing will fit on an 11-by-17-inch piece of paper. If you can-not print this at home, take the file to a copy center.

1. Print clip art. Cut out roughly around the wings, but cut pre-cisely around the body on one piece, and where the wing meets the body on the other piece. Mount the 2 pieces onto black heavyweight printer paper using spray adhesive.2. Stack both pieces face-up; the larger piece (with the butterfly body) should be on top. Using a hot-glue gun, adhere the 2 to-gether at base of wings, where indicated by dotted line. Let dry.3. Perch butterfly on furniture or other ledges using masking tape or adhesive hooks (such as Command hooks).

© 2010 Martha Stewart Living Omnimedia, Inc. All rights reserved. For personal use only, not for commercial use.

from Martha Stewart Living | www.marthastewart.com

Clip Art: “Fine Specimens” Wings Aflutter Large Perched Red Butterfly

glue

her

e

© 2010 Martha Stewart Living Omnimedia, Inc. All rights reserved. For personal use only, not for commercial use.

from Martha Stewart Living | www.marthastewart.com

How-to:Each wing will fit on an 11-by-17-inch piece of paper. If you can-not print this at home, take the file to a copy center.

1. Print clip art. Cut out roughly around the wings, but cut pre-cisely around the body on one piece, and where the wing meets the body on the other piece.2. Mount the 2 pieces onto black heavyweight paper using spray adhesive, aligning the 2 butterfly halves. Cut out around outline.

Clip Art: “Fine Specimens” Wings Aflutter Large Flat Red Butterfly

Clip Art: “Fine Specimens” Wings Aflutter Large Flat Red Butterfly

© 2010 Martha Stewart Living Omnimedia, Inc. All rights reserved. For personal use only, not for commercial use.

from Martha Stewart Living | www.marthastewart.com

© 2010 Martha Stewart Living Omnimedia, Inc. All rights reserved. For personal use only, not for commercial use.

Clip Art: “Fine Specimens” Wings Aflutter Large Perched Orange Butterflyfrom Martha Stewart Living | www.marthastewart.com

How-to:Each wing will fit on an 11-by-17-inch piece of paper. If you can-not print this at home, take the file to a copy center.

1. Print clip art. Cut out roughly around the wings, but cut pre-cisely around the body on one piece, and where the wing meets the body on the other piece. Mount the 2 pieces onto black heavyweight printer paper using spray adhesive.2. Stack both pieces face-up; the larger piece (with the butterfly body) should be on top. Using a hot-glue gun, adhere the 2 to-gether at base of wings, where indicated by dotted line. Let dry.3. Perch butterfly on furniture or other ledges using masking tape or adhesive hooks (such as Command hooks).

© 2010 Martha Stewart Living Omnimedia, Inc. All rights reserved. For personal use only, not for commercial use.

from Martha Stewart Living | www.marthastewart.com

Clip Art: “Fine Specimens” Wings Aflutter Large Perched Orange Butterfly

glue

her

e

© 2010 Martha Stewart Living Omnimedia, Inc. All rights reserved. For personal use only, not for commercial use.

from Martha Stewart Living | www.marthastewart.com

How-to:Each wing will fit on an 11-by-17-inch piece of paper. If you can-not print this at home, take the file to a copy center.

1. Print clip art. Cut out roughly around the wings, but cut pre-cisely around the body on one piece, and where the wing meets the body on the other piece.2. Mount the 2 pieces onto black heavyweight paper using spray adhesive, aligning the 2 butterfly halves. Cut out around outline.

Clip Art: “Fine Specimens” Wings Aflutter Large Flat Orange Butterfly

Clip Art: “Fine Specimens” Wings Aflutter Large Flat Orange Butterfly

© 2010 Martha Stewart Living Omnimedia, Inc. All rights reserved. For personal use only, not for commercial use.

from Martha Stewart Living | www.marthastewart.com

© 2010 Martha Stewart Living Omnimedia, Inc. All rights reserved. For personal use only, not for commercial use.

Clip Art: “Fine Specimens” Wings Aflutter Large Perched Yellow Butterflyfrom Martha Stewart Living | www.marthastewart.com

How-to:Each wing will fit on an 11-by-17-inch piece of paper. If you can-not print this at home, take the file to a copy center.

1. Print clip art. Cut out roughly around the wings, but cut pre-cisely around the body on one piece, and where the wing meets the body on the other piece. Mount the 2 pieces onto black heavyweight printer paper using spray adhesive.2. Stack both pieces face-up; the larger piece (with the butterfly body) should be on top. Using a hot-glue gun, adhere the 2 to-gether at base of wings, where indicated by dotted line. Let dry.3. Perch butterfly on furniture or other ledges using masking tape or adhesive hooks (such as Command hooks).

glue

her

e

© 2010 Martha Stewart Living Omnimedia, Inc. All rights reserved. For personal use only, not for commercial use.

from Martha Stewart Living | www.marthastewart.com

Clip Art: “Fine Specimens” Wings Aflutter Large Perched Yellow Butterfly

© 2010 Martha Stewart Living Omnimedia, Inc. All rights reserved. For personal use only, not for commercial use.

from Martha Stewart Living | www.marthastewart.com

How-to:Each wing will fit on an 11-by-17-inch piece of paper. If you can-not print this at home, take the file to a copy center.

1. Print clip art. Cut out roughly around the wings, but cut pre-cisely around the body on one piece, and where the wing meets the body on the other piece.2. Mount the 2 pieces onto black heavyweight paper using spray adhesive, aligning the 2 butterfly halves. Cut out around outline.

Clip Art: “Fine Specimens” Wings Aflutter Large Flat Yellow Butterfly

Clip Art: “Fine Specimens” Wings Aflutter Large Flat Yellow Butterfly

© 2010 Martha Stewart Living Omnimedia, Inc. All rights reserved. For personal use only, not for commercial use.

from Martha Stewart Living | www.marthastewart.com