Upload
others
View
7
Download
0
Embed Size (px)
Citation preview
AIBA OFFICIAL RING:
MANUFACTURER GUIDE
MANUFACTURER GUIDELINES:
AIBA OFFICIAL RING
2 - MANUFACTURER GUIDE: AIBA OFFICIAL RING
TABLE OF CONTENTS
RING DEFINITIONS ������������������������������������������������������������������������������������� 3
Canvas ��������������������������������������������������������������������������������������������������������� 4Apron ���������������������������������������������������������������������������������������������������������� 5Skirts ���������������������������������������������������������������������������������������������������������� 6Corner Pad ������������������������������������������������������������������������������������������������� 7Poles ����������������������������������������������������������������������������������������������������������� 8Ropes ��������������������������������������������������������������������������������������������������������� 9Rope Stripes ���������������������������������������������������������������������������������������������� 10Stairs �������������������������������������������������������������������������������������������������������� 11Corners’ Chair ������������������������������������������������������������������������������������������� 12Spit Containers ����������������������������������������������������������������������������������������� 13Logos and Prints ��������������������������������������������������������������������������������������� 14Storing Bags ��������������������������������������������������������������������������������������������� 15Assembly Guidelines ��������������������������������������������������������������������������������� 16
3 - MANUFACTURER GUIDE: AIBA OFFICIAL RING
RING DEFINITIONS
1: Apron2: Boxer’s Corner Pad3: Ropes4: Stripes5: Neutral Corner Pad6: Canvas
7: Poles8: Spit Containers9: Corner’s Chairs10: Ring Skirts11: Stairs
117
2
34
5
6
92
7
89
117
10
1 1
8
11
4 - MANUFACTURER GUIDE: AIBA OFFICIAL RING
CANVAS
CANVAS SPECIFICATIONS:
• For all AIBA Competitions, the ring must be6�10m square inside the line of the ropes
• Theringmusthavethedimensionssetoutinthediagram
• Thecanvasmustcovertheentireplatformandmust be made of non-slippery material
• Thecanvasmustbeblue,pantone299
780cm
610cm85cm 85cm
780c
m
610c
m85
cm85
cm
610cm 610cm
5 - MANUFACTURER GUIDE: AIBA OFFICIAL RING
APRON
APRON SPECIFICATIONS:
• The size of the apron must extend for 85cmoutside the line of the ropes on each side.However,thetotalsizeshouldbelongenoughtocover theedgeof the ringtobeconnectedwiththeskirts–around10cmwider,foratotalof800x800cm
• The color of the aprons should be blue,pantone299
• TheApronshallbeanon-slipperymaterialsuchas18ouncescottoncanvas(18oz/sqyard)
• Thefloormustbecoveredwith felt, rubberorother suitably approved material that is soft quality and elasticity. It must not be less than1.5cmandnomorethan2.0cm
780cm
610cm85cm 85cm
780c
m
610c
m85
cm85
cm
APRON
6 - MANUFACTURER GUIDE: AIBA OFFICIAL RING
RING SKIRTS
100c
m780cm
RING SKIRTS SPECIFICATIONS:
• The color of all skirts should be blue,pantone299
• Theheightofeachskirtshouldbe1m• ThematerialoftheskirtsshouldbeTapoline• All skirts should be separately connected by
Velcro–shouldnotbemadeofone longskirtwith31m20,but4separate7m80
• TheedgeoftheapronsandthetopoftheskirtsshouldalsobeconnectedwithVelcro
7 - MANUFACTURER GUIDE: AIBA OFFICIAL RING
CORNER PAD
100c
m13
0cm
780cm
610cm85cm 85cm
100c
m13
0cm
130
cm
230c
m
CORNER PAD SPECIFICATIONS:
• The material of the pads’ cover should beTapoline
• Theinsideofthecornerpadsshouldconsistoffoam and steel
• Thereshouldbethreedifferentcoloredpads 1Redcornerwhichshouldbered(185C) 1Bluecornerwhichshouldbeblue(286C) 2Neutralcornerswhichshouldbewhite
• Thecornerpadsshouldnottouchthecanvasorthe aprons
• The lengthof thecornerpadsshouldcoverallropes
CORNER PAD
CORNER PAD
8 - MANUFACTURER GUIDE: AIBA OFFICIAL RING
POLES13
0cm
230c
m
85cm
POLES SPECIFICATIONS:
• Thetotalheightofthepolesshouldbe230cm• Theheightabovethecanvasshouldbe130cm• Thebottompartofeachpoleshouldbecovered
byfoam(1mfromtheground)andthereshouldbe a steel pole inside the form
• Thelocationofthepolesshouldbe35cminsidethe edge of the ring
100c
m13
0cm
130
cm
230c
m
POLE
POLE
9-MANUFACTURERGUIDE: AIBA OFFICIAL RING
ROPES13
0cm
30cm
40cm
30cm
30cm
ROPES SPECIFICATIONS:
• The ropes must be covered by a thickpadding
• The ring must include four (4) separateropesoneachsideofthecornerposts.Theymust be 4cm thick, without consideringthecover
• Theheightsofthefour(4)ropesmustbe40cm, 70cm, 100cm, and 130cm fromthecanvas
• ThematerialofallropecoversshouldbeTapoline
• Ropesshouldbewhite• Thetensionofeachsectionofthetoptwo
ropes must be tight enough� The tension of bottom two must not be too tight
ROPES
ROPES
10 - MANUFACTURER GUIDE: AIBA OFFICIAL RING
ROPE STRIPES
ROPE STRIPES SPECIFICATIONS:
• Thefour(4)ropesmustbejoinedoneachsideofthering,atequalintervals,bytwo(2)piecesofmaterial(closetothetextureofthecanvas)3to4cmwide
• The two (2) pieces must not slide alongthe rope
• Inadditiontothestripes,thereshouldbe3Velcrostripeholders
• Thecolorofall stripesandof theVelcrostripe holders should be white
• The material of all stripes should beTapoline
11 - MANUFACTURER GUIDE: AIBA OFFICIAL RING
STAIRS
STAIRS SPECIFICATIONS:
• Thestairsshouldhaveonly3steps• Thereshouldbe3stairs• The color of the3 stairs shouldbe: one
red(PANTONE185C),oneblue(PANTONE286C)andonewhite
• Thetotalheightofthestairsshouldbe75cm• Thewidthofthestepsshouldbe80cm• Theangleofinclinationofthestepsshould
be 54 degrees• ThestairsshouldbemadeofFRPmaterial• Thestepsshouldbeantislippering• Thestairsmustnotbefixedtothering• Thestairsmustbemoveable
25cm
25cm
25cm
25cm
75cm
80cm 80cm
75cm
54°
25cm
25cm
25cm
25cm
75cm
80cm 80cm
75cm
54°
ANTISLIPPERY SURFACE
12 - MANUFACTURER GUIDE: AIBA OFFICIAL RING
CORNER’S CHAIR
CORNER’S CHAIR SPECIFICATIONS:
• The two corner chairs must be swingchairstocomeinandoutoftheringbybeingattachedtothepoles
• Each chair must be displayed in blue(PANTONE286C)orred(PANTONE185C)accordingtotheirrespectivecornercolor
• The maximum distance between thechairsandthecornerpadsis15cm
• The diameter of each chair should be25cm
max
. 15c
m
30cm
50cm
13 - MANUFACTURER GUIDE: AIBA OFFICIAL RING
SPIT CONTAINERS
SPIT CONTAINERS SPECIFICATIONS:
• Thecontainer shouldbemadeofplasticmaterial and displayed in red (PANTONE185C)orblue(PANTONE286C)color
• Themaximumdimensionis25centimeters• Thediameterofthecontainer’stubemust
not be larger than 15 millimeters• Thehose(orpile)mustbeattachedtothe
pole or ropes and be removable• Thehoseshouldbecolorizedaccordingto
theredandbluecorner15
mill
imet
ers
larg
e
25cm
rope
14 - MANUFACTURER GUIDE: AIBA OFFICIAL RING
LOGO AND PRINT
LOGOS & PRINT SPECIFICATIONS:
• only one manufacturer logo can bedisplayed at the neutral corner, wherethere’s no stairs
• Maximum size of manufacturer logo is25cmx25cm(625cm2)
• EquipmentOfficialSupplierlayoutwillbeprovided by AIBA
• AnyEventlogoshallbeprintonthemiddleoftheCanvas.Incaseofnoevent,pleaseconsultwithAIBAwhattoprint
• Eventlogomaximumsizeis200x200cm
OFFICIAL SUPPLIEREQUIPMENT
60cm
80cm
10cm
10cm
200cm
200c
m
EVENT LOGO
15 - MANUFACTURER GUIDE: AIBA OFFICIAL RING
STORAGE BAGS
STORAGE BAGS SPECIFICATIONS:
• The following parts should be storedproperly in each storage bag with serialnumbers
o 1ringskirt(4parts) o 2canvas o 2 apron o 4 ropes o 8stripeswithVelcrostripeholders
STRIPES
CANVAS
APRONS
ADDITIONALCANVAS
SKIRT(4 PARTS)
ROPES
16 - MANUFACTURER GUIDE: AIBA OFFICIAL RING
ASSEMBLY GUIDELINES
ASSEMBLY GUIDELINES:
• An introduction booklet for assemblingtheringshouldbeincludedinall5AIBAlanguages and this for all AIBA rings – English, Spanish, Russian, Arabic andFrench