Upload
others
View
0
Download
0
Embed Size (px)
Citation preview
BST-DL09
Sing�e-Use USB PDF Temperature and
Humid�ty DataLogger
Manual
V1.0
BESANTEK Corporation, CANADA
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com
Content
Chapter I: Product introduction ....................................................................... !
1.1 Product introduction ................................................................................................................. !
1.2 Application ................................................................................................................................ 1
1.3Prod uct Feature ........................................................................................................................ 1
1.4Performance Parameters ........................................................................................................ 2
Chapter II: Instruction Manual ......................................................................... 3
2.1 Instrument appearance specification .................................................................................... 3
2.2 Instrument instructions ........................................................................................................... 4
2.3PDF document description ..................................................................................................... 7
Chapter Ill: Precautions .................................................................................. 10
BESANTEK Corporation, CANADA
Chapter I Product Introduction
1.1 Product Introduction
This product carries a new type of microcontroller, one-time record. Ability to generate
PDF documents on their own, the user can access a variety of devices, easy to quickly
browse recorded temperature and humidity data. Instrument equipped with a small LCD
display, temperature and humidity at the same time display, user-friendly browsing to
real-time temperature and humidity information, display data can be accurate to one
decimal places, and eye-catching battery tips, always remind the electricity situation. At the
same time, through the key switch, the user can get other information they need, including:
the maximum recorded, minimum recorded, upper and lower limits of temperature and
humidity. In addition it has a user-friendly mounting bracket can be fixed screws,
installation more convenient and safe.
1.2Application
The product can be applied to cold storage, vaccines and blood products, food cold
chain transportation, containers transportation, outdoor and other special environment.
1.3Product Feature
• IP67 waterproof and dustproof design, resistant to moisture, condensation and dust
• Low-power design, 1 / 2AA 3.6V lithium battery can work continuously for 6 months or
more
• Comes with operating software, multiple data protection mechanisms to ensure that
data is never lost
• high sensitivity probe, fast response, high precision
• maximum to record 7200 temperature and humidity data
• Instrument will connected with the computer to automatically generate PDF
documents to view the analysis data more convenient and quick
1
BESANTEK Corporation, CANADA
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com
1.4Performance Parameters
Parameters Parameter index Parameters Parameter index
1/2AA 3.6V Lithium Temperature
Voltage battery
measuring -30~70 °Crange
Working Temperature
-30~70°
C measuring +0.5 °CTemperature
accuracy
Relative
Size 125*28*22mm humidity
0~100% RH measuring range
Relative
Weight 62g humidity
+5%RHmeasuring accuracy
Measuring About 50 rrl
Interval 10s
area logging
2
BESANTEK Corporation, CANADA
Chapter II Instruction Manual
2.1 Instrument appearance instructions
� --,
CD®
26.6j OK
o· 691 \
@ ®
Figure 2-1 Front appearance diagram
1 - OK button : Instrument shutdown state, connected to PC set synchronize and time,
long press this button for 3 seconds, the instrument boot and automatically enter the
calibration mode, press this button again equipment shut down, turned off after press this
button switch on the instrument into the recording mode.
3
BESANTEK Corporation, CANADA
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com
When the instrument is turned on, press (short press) this button, the LCD will
switch the display (real-time data, minimum value MIN, maximum value MAX, alarm lower
limit LO, alarm upper limit HI cycle switching).
Instrument boot record state, long press this button for 3 seconds, the instrument off.
2 - Humidity light : The instrument records and humidity over limit state, the light once
every 10 seconds, indicating that the humidity is exceeding limits.
3 - Temperature light : The instrument records and temperature over limit state, the light
once every 10 seconds, indicating that the temperature is exceeding limits.
4 - LCD display
5 - USB interface : for the instrument access to the computer.
6 - bracket : can be fixed screws, installation and use more convenient.
26. t
6 9 ]�"A ®3 �--........ --• ____________ .,...
Figure 2-2 LCD display diagram
1 - Real-time temperature : The unit is 0
c
2 - Real-time humidity : The unit is %
3 - Battery Level : Full grid is 3 grid
2.21nstrument instructions
Use Step : set the instrument and synchronize the time - instrument turn on and
boot into calibration mode - the instrument turn on again, and recording data normally -
connect to the computer, open the PDF view and save data - end use.
1.Set the instrument and synchronize the time : Connect to the computer by USS
interface - Open the DataLogger software - Click [Get] to get the instrument
configuration - Pop-up the ok prompt window, click [OK] - set the instrument upper
and lower limits alarming and interval logging - click [Sync Setting] synchronization
settings.
BESANTEK Corporation, CANADA
-�ii.,?,l�!Piiir--------
Temperture & Humidity Data logger 1 ----- 2;..._.---c:r;;.,sN, 1� €•mV.,..;o�" vu::=::,
AlarmSea.,p 3
RMord..,_,.,.J
5
F
Get I Syiw:k� I
Figure 2-3DataLogger software interface
1. The serial number of the instrument: corresponding to the series number of labelon the back of the instrument.
2. The program version of the instrument.
3. Temperature alarm upper and lower limit setting: the temperature measured by
the instrument is not in the range of the setting upper and lower limit, instrumentwill be alarming state.
4. Humidity alarm upper and lower limit setting: the humidity measured by theinstrument is not in the range of the setting upper and lower limit, instrument will
be alarming state.
5. Display unit: temperature display unit is 0c, humidity display unit is %
Note: Select [Fl option without any impact, the unit temperature is still
displayed 0c.
6. Record interval settings: every set interval, the instrument records a piece of data
in seconds, The set range is 5~43200S.
7. Check the "Update" option, the instrument synchronizes the computer time.
5
BESANTEK Corporation, CANADA
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com
2.lnstrument boot, enter calibrat ion mode: After synchronizing time, the instrument is
pulled out from the computer, press the OK button to power on, the instrument enters the
calibration mode, normal display real-time temperature and humidity, can check the
maximal value, minimum value , alarm lower limit and alarm upper limit, Does not display
temperature and humidity units, does not generate PFD documents. As shown in Figure
2-4:
26.6 69]
Figure 2-4 Calibration mode LCD display Figure 2-5 Record mode LCD display
3.lnstrument is power on again, record data: Press OK to turn off the instrument after
entering the calibration mode. The instrument will turn on again and enter the record state.
At this moment, the instrument starts to record the data and normally display temperature
and humidity to generate the PDF document
4.View data and save data: let instrument USB interface directly connect to the computer,
waiting for the generation of PDF documents (according to the quantity of data recorded,
will take a different time), after generate the PDF document, "computer "will appeared a
removable storage device. After opening this disk, a PDF file will appear. Click this file to
read the data recorded by this instrument, and can copy and paste the PDF document to
other computer disk.
Note 1: It is suggested to rename the PDF document according to actual
needs after copying the PDF document.
Note 2: the recording capacity of this instrument is 7200 sets of data. After the
data storage reaches the upper limit, the LCD humidity column will show "FUL"
and the instrument has finished recording.
5.End use: This product is a one-time use, so the instrument power off or connect to the
computer in the recording state and the instrument can't power on or can't be
6
BESANTEK Corporation, CANADA
re-record after synchronized instrument setting, but can be connected to the
computer to view and save the data.
2.3 PDF document description
1.PDF generation: After the instrument is connected to a computer, the PDF document
will be generated. At this time, the temperature light will flash and the representative is
generating PDF. After the PDF is generated, the user can read the recorded PDF
document from the instrument.
2.PDF document interface description:
7
BESANTEK Corporation, CANADA
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com
AJann SIB!us Alarm
1- Up o.i,y; 0 min
Recorded Data flrllPoioL S4"1'Tlmo< Nwr6er or Pc:ihts! Trlp�
Alarm 1
2
-·
:���::���� 4 271 5 Odoy• r,S1 min 6
Data Logger
M0flll04'Read
1
°"' 2017/lt/1813:18:12 Nal&.MTmet:lnGMT
-S<!<llngS. u .... 20.0{Tetf1p.)120.0(Hlmd.) 8 --... O(T-)lllj� 9 Tngge,ecl:
(JO(
Originator Notes
12
rc1 .... 14 L_ -_'-'-' ___ -____ -____ -_-__ -_______ ---------
13
By. usa
7
a.1,1-----!-----11----+----t----t-----+-----i- ....
2U •
v' 21.•
1U
... ,
..... ,.._ ___ r----11----t----t----t-----+-----i- 11.•
,u,1----+----1----1----t----+----1-----,..-
21111-----+----1-----1----1----1----1-----+ ff�
�-•�----+----1-----1--------�-------�-
zu•l-----+----1-----l----1----1-----1----1- ,._,
20.2
Figure 2-6 PDF Document Page 1
1) Instrument serial number
2) Over limit alarm prompt: blank= no alarm, red= alarm.
3) Set the recording interval, unit: second
4) Instrument recording start and end time
8
,..,
BESANTEK Corporation, CANADA
5) Total number of data recorded
6) Record the total length of time
7) The maximum, minimum and average temperature and humidity recorded by the
instrument.
8) Set the lower limit of temperature and humidity
9) Temperature and humidity exceed the minimum number of limits set
10) Set the upper limit of temperature and humidity
11) The first excess lower limit and the last excess lower limit time
12) Excess the Min value in over limit state: No over limit record display OK, there is over
limit record shows Alarm.
13) Excess the Max value in over limit state: No over limit record display OK, there is over
limit record shows Alarm.
14) Temperature and humidity analysis curve: blue curve for the temperature, yellow
curve for the humidity.
15) Temperature and humidity exceed the maximum number of limits set.
Temperature And Humidity """' Dula
%:H.tunl ID Tli-2 !i..!J �ll "Hllf.tlJ 11' 1Q � 11 � VI f ..-,v,1 o; 10 !ii 11.l Ill' Jll11Q11 IK'Hffl ,.;r Iii f N171Jl'rlJ llRil jB IU £51 5111&.TU 0,1111 uu 15.:t
...,...,_..,,..,.._...,..__,.__"-'11111J6:r1J Dl112t 11..J. �.I lt1ta1, att • 1.l.!i -., >01:W.-IJ bt ''"' '•-" j,lj_] .>.11"1,t> ,,.,.., •• ,., "'� �11Q'!) 1M ,,.�, ,., �" �lt�1 Ql.llN llJ' wq il£1711:1:'1J 8"1�'W 1tll..1 r;,5 • at11,:<i,11 ll' � II� .Ir,_ i 1':W1101'1 1 JJt lUiil 11.2 Vi A
_,.,..,,...,,...,,:r_....,... ..... �:ierj =� ::� :�..tDITC:.IJ l»\1_:W I._I W �tl.O'U m...1U1 tfl 1 .Mt
i.;,,.""",...,,,.,.; .... ..,... ........ :::�== !:: ::
unrcti,u aa..a..n •• , llil • lltJ/,..,r,J, ""'""' ,., 1111-4 .JIIIT�I I 01.2JII-H �- 1 lil 4 JIIVfl.QIIJ 0-,l11}"; ,-., M1 'J0•.1i1Ditl aw:, 1111 • 1 w:.ii nto.«.a•1 ona ••1 • t MT.fll!li 111.:T llt 11., !ii�
�:=3�: ::� :!":tt,,'!1'W1.) ftli'.aQf ,. t ....
::�;-;::�: ::� ::illf7WQ"-l�OriYIM 1111 ., J9Jt-To11JPLJ �1-ntA"f k 1 "Dl..1 Jln/fM!rJ ill!r.Dl9 1& 1 ■.1
,o,rnwuoa:..ta .-., ,._, .111,1,ml•l Ol'II • 1•i fiLI JDl!fllllll lllt..au, ta I ai ..flrl11Ci\J D.ft..Jt 11l.. t A..lllll�Q,nraa •• ., )l'lff'i1il1ft,WM lat IIL.I
C!olo 11rre ·c .m,tADr,• t»�..Jlt 1a I -.., JIJI r.v1,1,1 ■ -o-4■ I� t :tU J111T,IW11 WQW •• I M • JDfTflllU )q'Q-Of "• I M• »tfllWU 08-, II •.t I .HI m,r.unu 15.,,i, 111 •• .:»trtDf1l OI-O !I -. I k,I 2111.0U"II �-il •• IA I 1111 II �1?.nml � ta: ' --· l01toftllnaU.4.IJI 1,t �1
�=�=;: �;� ::mff,118,Q c9 .. , ..... p.-;r>-f'l-}Ollt• � •• •fll M 1 .111'MID11 rn.,_ 5lt 'lS.J 916.• ...»11.0::,,2-.eat JU•• '"JD1'1Ui•U MQ111 � Kc zr1/AWlllll-tl...Jlt 'tA.J •c.:
'.llnt.UOU .W.4!:llt '8..J ..!IILI 2111,1,QJU •---•• •k) • t .IDtNl'ltU llJ &IA t._ l .._.__
Figure 2-7 PDF Document Page 2
1. Normal data display
X1+�-u � ", M.JJellQ13.,....,,.q flll' Q-110HUU'lll'-ll..6't 1!1--Mi.l
.wnun nc-11111 117 �.J Jll'rlDtll .111511!1 ti, IIU IEO-DO Dill iPJ ti l IIU J011.wn,-• ,ar s, 'JStlft#\.1 MdiloM ,■, � t m11m,,� -c911 •• I a,
,,,.,,...,.u t�ta lO f !JI I �tl'l;ltl '"'°° f3 1111--, M • ,.1111111> ltOOl'I '"I ,0 Iilff?IQrn !NOS 111 9\t i,r,l1"1li11 t,;,oo .. llf lltlb sn ffl,I •c«JS , • ..,. MO a, ,mru rot-, � ,.._, bt.t 11:11,LJ.'ll tftl ,1 111 �V m:01, �1.211 t1 f �u a;_, ''Ul't1 l6l.1.JI ,. ; t.1.1 1C1�1, fftt ct Of r Ml .,.,..,11 �·- .. , !\it
2. Over-limit data display (temperature and humidity data will display blue if the value
are excess)
9
BESANTEK Corporation, CANADA
Chapter Ill Precautions
1. The PDF generation will take a certain amount of time. During this time,
the instrument will not be pulled out from the port, otherwise the data will be
lost.
2. After the instrument is connected to the computer, the instrument will be
automatically ended the recording function and shutdown.
3. Button operation will increase the power consumption of the instrument,
and avoid a large number of useless operations on the keys when
necessary.
4. It can not be used for the second time if the instrument power off when
recording the data, so please do not turn off or connect the machine to the
computer during the recording process.
(VER 1.0)
10
BESANTEK Corporation, CANADA
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com