Embed Size (px)
Citation preview
RGB ILLUMINATION SET
MANUAL
2
1. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Pacelight P1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2 Pacelight RGB LED Strip S1 . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.3 Pacelight RGB Fan F1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.1 Connect to the Mainboard . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.2 Connect to the Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.3 Connect the Fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.4 Connect the LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.5 Attaching the Pacelight P1 . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4. Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5. Menu Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6. Fan Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7. LED Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7.1 Manual LED Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7.2 Channel Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7.3 LED Control by Week . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.4 Lighting Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7.5 Advanced Lighting Options . . . . . . . . . . . . . . . . . . . . . . . . . . 17
8. Fan Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
9. Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
9.1 Fan Failure Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
9.2 Time Control Dimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
9.3 Assign Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Table of Contents
3
1.1 Pacelight P1
RGB Channels 8
Fan Channels 4
Input Voltage 12 V DC
Connector 15-Pin SATA
USB Connector 9-Pin Internal
Max. LED Current 50 mA (Per Color)
Max. Fan Current 0.5 A (Per Connector)
Fan Output Voltage 12 V
Max. Fan Starting Current 2 A
Microcontroller 4x 8bit MCU
Fan Controller Type PWM
LED Controller Type PWM
Supported Operating Systems Windows 7/8/10
Fixation Self-Adhesive / Cable Tie
Weight 44 g
Cable Length 60 cm
Dimensions (L x W x H) 110 x 66 x 11 mm
1.2 Pacelight RGB LED Strip S1
LED Type 5050 RGB
Length 360 mm
Width 10 mm
No. of LEDs 18
Connector 4-Pin (2.54 mm)
Pinout 12 V – G - R - B
Cable Length 60 cm
Fixation Magnetic / Self-Adhesive
Rated Voltage 12 V DC
Rated Current 280 mA
Weight 30 g
Dimensions (L x W x H) 360 x 10 x 3 mm
1. Specifications
4
1.3 Pacelight RGB Fan F1
General
Fan Speed 1,400 rpm ± 10 %
Bearing Type Fluid Dynamic Bearing
Max. Airflow 93.22 m³/h
Max. Air Pressure 1.13 mm H²0
Max. Noise Level 23 dB (A)
MTBF Min. 50,000 Hours
Illumination 6x RGB LED
Connector Fan 3-Pin Connector
Connector LED 4-Pin (2.54 mm)
Pinout 12 V – G - R - B
Cable Length 50 cm + 5 cm LED / 45 cm Fan
Electrical Specifications
Rated Voltage 12 V
Rated Current Fan 0.15 A
Rated Current LED Fan 0.08 A
Rated Power Fan 1.8 W
Rated Power LED Fan 1 W
Start Voltage 5 V
Weight incl. Cable 125 g
Dimensions (L x W x H) 120 x 120 x 26 mm
1. Specifications
5
2. Safety Instructions
In some cases, certain individuals may experience epileptic seizures if exposed to certain light frequencies, flickering light sources and patterns. Consult your doctor if you or one of your family members suffer from epilepsy. Even some people without a history of seizures or epilepsy may have an undiagnosed ailment. Seek medical attention if any of the following symptoms occur: visual impairment, eye and muscle twitching, loss of consciousness, disorientation, involuntary movements and spasms.
The Pacelight RGB LED Strips S1 contain magnets for mounting. To prevent data loss, do not install them near HDDs, SSDs, DRAM or other storage devices.
Sharkoon assumes no liability for any data loss, especially due to improper handling.
6
3. Installation
3.1 Connect to the MainboardTurn off your computer before installing the Pacelight P1, fans and LED strips.
Then connect the provided USB cable, as shown, to the Pacelight P1 and the internal USB port on the mainboard.
3.2 Connect to the Power SupplyTo power the Pacelight P1, connect an available SATA plug from the power supply, as shown.
7
3.3 Connect the FansUp to four fans, with or without LEDs, can connect to the Pacelight P1. Please refer to the following section for information on connecting the LED fan control and LED strips.
To connect a fan, attach its 3-pin fan connector to the indicated connector of the Pacelight P1.
3. Installation
8
3.4 Connect the LEDsUp to eight LED elements can be connected to the Pacelight P1. To connect the LED fan control or LED strips, connect the 4-pin LED connector to the Pacelight P1, as shown. For fans or LED strips from third party manufacturers, ensure that the correct connector layout is 12 V – G - R – B.
Always combine the connection of the fan with its corresponding LED control. Start in ascending order, beginning with the “FAN1” / “LED1” marked connectors on the Pacelight P1.
Note: When connecting the LED control or LED strips, ensure that the 4-pin LED connector is aligned correctly. This is marked with an arrow, as is the connector of the Pacelight P1. The two arrows must be aligned across from each other, as shown.
3. Installation
9
3.5 Attaching the Pacelight P1Attach the Pacelight P1 to the inside of the case with the self-adhesive backing or by running cable ties through the cutouts in the silicone pad.
Caution: Do not remove the silicone pad on the Pacelight P1; short-circuiting may result if it directly contacts a conductive surface.
After successful installation, turn on your computer.
3. Installation
10
4. Software Installation
Download the Pacelight P1 software directly from the Sharkoon homepage at www.sharkoon.com. Unzip the zip file to a location of your choice and then double-click on Pacelight_Setup.exe to launch the installation.
Follow the instructions on the installation wizard. The default installation language will automatically be the same language as your operating system. To change the language at any time, right-click on the icon in the taskbar.
After restarting your computer, the Pacelight software will automatically appear in your taskbar. Ensure that the Pacelight software is always active in the background to access its full functionality.
11
5. Menu Overview
LED control:
Adjust the illumination of the connected LEDs manually or by day of the week. It is also possible to select and control lighting effects.
Fan control:
Test here the connected fans for compatibility and also control the fan speed. Infographics for each connected fan are displayed within the overview.
Advanced:
Set a fan failure warning with custom illumination, dim LEDs according to time of day, or assign LEDs a custom illumination based on the active program.
C
A
B
C
A B
12
6. Fan Compatibility
The Pacelight P1 is designed and optimized for use with the Pacelight RGB Fan F1. When using fans other than the ones included with the Pacelight P1, they must be initialized.
To initialize a fan, open the “Fan Control” menu and click on the gray fan icon below the on/off slide bar for the fan needing to be initialized. The fan icon will change color to blue during initialization. The duration of the initia-lization depends on the hardware and may take a few minutes.
The corresponding fan is compatible if the fan icon turns green at the end of the initialization. If it turns red, the Pacelight P1 cannot control the fan. If it remains blue, the initialization must be restarted.
13
7.1 Manual LED Control With the manual LED control, up to eight LED channels can be controlled within the single color, multi colors or rainbow colors lighting modes.
To do this, first click the on/off slide bar to activate the desired LED channels. A freely chosen name can also be assigned to each channel in the text field next to it. Use the adjacent drop-down menu to select the desired lighting mode.
7. LED Control
14
7.2 Channel SynchronizationWith the manual LED control, the possibility exists to synchronize the pulsating and stroboscope lighting effects for selected LED channels. For more about the lighting effects, go to the “Advanced Lighting Options” section.
During synchronization, the lighting effect set under “LED1”, along with the selected frequency, will also transfer the same lighting effect to the individual selections “LED2” to “LED8”. The selected lighting modes are not affected.
To synchronize LED channels, click on the arrow icon, located to the right of the on/off slide bar, of each channel to be synchronized. The synchronization icon color will change from gray to blue when active. Depending on the hardware, the synchronization process can take up to several seconds.
7. LED Control
15
7.3 LED Control by Week All active LED channels can be regulated collectively by day of the week through the LED control week listings. The lighting modes single color, multi colors and rainbow colors are also possible.
First, activate the LED channels by clicking the on/off slide bar next to the desired day of the week. Then use the drop-down menu next to the day to select the lighting mode bundle for all active LED channels. In addition, lighting effects can also be selected. See “Advanced Lighting Options” for more information.
Depending on the hardware, the lighting mode updates can take up to several seconds.
7. LED Control
16
Single Color:
The single color lighting mode permanently illuminates the corresponding LEDs in one of the 16.8 million colors. The color selection is made through either a circular color selector, RGB slider or a predefined color palette.
Multi Colors:
The multi colors lighting mode illuminates the connected LEDs in six of 16.8 million colors, alternating the color at intervals of one second. The color selections are made through either a circular color selector, RGB slider or a predefined color palette.
Rainbow Colors:
No colors are selected for the rainbow colors mode. Instead, the colors red, yellow, green, blue, light blue and pink alternate without in-terruption at an interval rate of one color per second.
7. LED Control
7.4 Lighting Modes
17
7.5 Advanced Lighting OptionsEvery LED can be assigned one of two lighting effects in addition to its general lighting modes: Pulsating dims the LEDs in short intervals; stroboscope lets them flicker frantically. Each frequency can be slowed or quickened via the adjacent slide bar.
It is also possible for the manual LED control and day of the week LED control to transfer settings from one LED channel to another. To do so, first select the LED channel to be changed by clicking on the colored box to the right of the lighting mode. Ensure that no LED channels are synchronized. Then, under “Copy Settings From” within the illumination mode window, select the LED channel whose settings are to be transferred to the current LED channel.
7. LED Control
18
8. Fan Control
Fans can be initialized within the „Fan Control“ tab, with the fan speed being controlled for initialized fans up to 12 V in a range defined during initialization.
To adjust the fan speed of an initialized fan, first activate it by clicking the on/off slide bar. For a better overview, the fan can be renamed in the adjacent text field. Then, by using the slide bar, the fan speed can be individually adjusted.
For better control, the infographic fields measure volts and fan speed of the respective fan in intervals of every few of seconds. Above the slide bar, the info field lists detailed values of the volts, RPM and current amp rate.
19
9. Advanced
9.1 Fan Failure Warning In the event of a fan failure, a warning can be set within the “Advanced” menu. The corresponding LEDs will blink in a specified color 20 seconds after the failure. An exclamation mark is also displayed in the task list until the problem is solved.
To set up a warning, activate the feature by clicking on the slide bar next to “Fan Failure Warning”. Click on the gears icon to open the corresponding color selection. You can also select a color via the circular color selector, RGB slider and predefined color palette.
In the event of a fan failure, the affected fan is turned off when normal speed fluctiations have been excluded. In addition to manually eliminating the fault, the option is also available to turn off the fan warning via an additional warning message and then return it to the last known LED setting.
20
9.2 Time Control DimmerAlso found in the “Advanced” menu is the Time Control Dimmer. With this, the corresponding LEDs can be dimmed overall within a fixed period from an individual value between 50% and 100%.
To enable LED dimming by time, activate it by clicking the on/off slide bar next to “Time Control Dimmer”. Then, click on the gear icon to open the time and dimming selection window. Insert the desired values manually or click on the drop-down menus.
9. Advanced
21
9.3 Assign Program Under “Assign Program” within the “Advanced” menu, custom illumination can be set up into five programs. Whenever a saved program is launched, the corresponding LEDs will change to the colors defined within that program. If more than one program is launched from the list, priority is given according to the preceding numbers (1 to 5).
To assign programs and lighting, activate the on/off slide bar next to “Assign Program” and then click on the gear icon. The standard illumination modes of single color, multi colors and rainbow colors are available.
To assign a program, click on the folder icon next to the program name and then choose the path to the exe file of the program. Delete the complete program path to deselect the program, or assign another program via the folder icon.
9. Advanced
22
Legal Disclaimer
Legal Disclaimer:For potential loss of data, especially due to inappropriate handling, SHARKOON assumes no liability.
All named products and descriptions are trademarks and/or registered trademarks of the respective manufactu-rers and are accepted as protected.
As a continuing policy of product improvement at SHARKOON, the design and specifications are subject to change without prior notice. National product specifications may vary.
The legal rights of the enclosed software belong to the respective owner. Please observe the license terms of the manufacturer before using the software.
All rights reserved especially (also in extracts) for translation, reprinting, reproduction by copying or other technical means. Infringements will lead to compensation. All rights reserved especially in case of assignation of patent or utility patent. Means of delivery and technical modifications reserved.
Disposal of your old product:
Your product is designed and manufactured with high quality materials and components, which can be recycled and reused.
When this crossed-out wheeled bin symbol is attached to a product, it means the product is covered by the European Directive 2012/19/EU.
Please be informed about the local separate collection system for electrical and electronic products.
Please act according to your local rules and do not dispose of your old products with your normal household waste. The correct disposal of your old product will help prevent potential negative consequences to the environment and human health.
SHARKOON Technologies GmbHSiemensstraße 38D-35440 Linden Germany
© SHARKOON Technologies 2018
