MANUAL DE OPERACION SHARP AR-M450

LASER PRINTER

Operation Manual (for copier)

Be sure to become thoroughly familiar with this manual to gain the maximum benefit from the product.

Before installing this product, be sure to read the installation requirements and cautions sections of the "Operation manual for printer operation and general information".

Be sure to keep all operation manuals handy for reference including this manual, the "Operation manual for printer operation and general information" and operation manuals for any optional equipment which has been installed.

cover1.p65 4/17/01, 9:50 AM1

cover1.p65 2/04/01, 19:172

1

INTRODUCTIONThis manual describes only copier features. For operation procedures relating to both the basic printer and copierfeatures, refer to the “Operation manual (for printer operation and general information)”. General information required forloading paper, adding toner, misfeed removal, and operation of peripheral devices are described in that manual.

Separate manuals are provided for the operation of network scanning and facsimile functions. Refer to the “Operationmanual (for scanner)” and “Operation manual (for facsimile )” for these descriptions.

copy-1_Ep.P65 2/04/01, 19:171

2

CONTENTSPage

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

PART NAMES AND FUNCTIONS (B/W scanner module/DSPF) . . . . 3

� Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

� Operation Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

� Touch Panel (basic screen of copy mode) . . . . . . . . . . . . . . . . . . 5

AUTOMATIC DOCUMENT FEEDER . . . . . . . . . . . . . . . . . . . . . . . . . 6

� Acceptable originals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

SETTING ORIGINALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

NORMAL COPYING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

� Copying from the automatic document feeder . . . . . . . . . . . . . . . 9

� Automatic two-sided copying from the automaticdocument feeder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

� Copying from the document glass . . . . . . . . . . . . . . . . . . . . . . . 12

� Automatic two-sided copying from the document glass . . . . . . . 14

EXPOSURE ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

REDUCTION/ENLARGEMENT/ZOOM . . . . . . . . . . . . . . . . . . . . . . . 16

� Automatic selection (auto image) . . . . . . . . . . . . . . . . . . . . . . . 16

� Manual selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

SPECIAL PAPERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

SPECIAL MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

� Common operation procedure for using the special functions . . 19

� Margin shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

� Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

� Dual page copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

� Pamphlet copy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

� Job build . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

� Multi shot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

JOB PROGRAM MEMORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

� Storing a job program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

� Recalling a job program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

� Deleting a stored job program . . . . . . . . . . . . . . . . . . . . . . . . . . 27

INTERRUPTING A PRINT OR COPY RUN . . . . . . . . . . . . . . . . . . . 28

MISFEED REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

� Misfeed in the scanner module . . . . . . . . . . . . . . . . . . . . . . . . . 29

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

� Copier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

� Scanner module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

KEY OPERATOR PROGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

� Key operator program list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

� Using the key operator programs . . . . . . . . . . . . . . . . . . . . . . . . 32

� Setting programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

copy-1_Ep.P65 2/04/01, 19:172

3

PART NAMES AND FUNCTIONS(B/W scanner module/DSPF)Exterior

DSPF exit areaScanned originals are deposited here.

Document feeding area cover (page 29)Open to remove misfed originals in this area.

Original guides (page 7)Adjust to the size of the originals.

Document feeder tray (page 7)Set the originals here for automatic feeding.

Operation panel (next page)Use for operation of copier, network scanner, andfacsimile features and for printer configurationoperations.

Document cover

Document scanning windowsSheet type originals are scanned here.

Document glassAll originals which cannot be copied from thedocument feeder tray must be copied here.

copy-1_Ep.P65 2/04/01, 19:173

4

Touch panel (next page)The machine status, messages and touch keys aredisplayed on the panel. When the machine is in thestandby state, the display will change if the [PRINT]key, [IMAGE SEND] key or [COPY] key is pressedto show the current status of these modes.

Mode select keysUse to select the basic modes of the product.

[COPY] keyPress to select the copy mode and display the basicscreen of the copy mode. (next page)Even when the machine is busy in another mode,the basic copy mode screen will appear when the[COPY] key is pressed. If this key is pressed andheld while the basic screen of the copy mode isdisplayed, the total output count and the quantity oftoner remaining (percentage) will be displayed.

Numeric keysUse to select the number of copies and to makenumerical entries for setting operations.

[C] key (clear key)Press to clear a copy quantity entry. If this key ispressed while the automatic document feeder isbeing used, any originals in progress will beautomatically output.

[CA] key (clear all key)Press to clear all selected settings and return themachine to the initial settings for the currentlyselected mode. Before starting a copy operation,press the [CA] key first.

[ACC.#-C] keyIf the auditing mode has been set, press this key toclose an open account after finishing a copy,facsimile scanning or network scanning job. Forsetting of the auditing mode, see page 7 of the KeyOperator’s Guide.

[#/P] key (page 26)Press to select the job memory mode.

[START] key (page 10)When the indicator is lit, copying, facsimile scanningand network scanning jobs can be started. Press tostart copying.

PART NAMES AND FUNCTIONS

Operation Panel

copy-1_Ep.P65 2/04/01, 19:174

5

Touch Panel (basic screen of copy mode)When the copy mode key is pressed, this display screen will appear showing the basic copy mode selections.(For the display screens for other modes, see the respective operation manuals for those modes.)

Message displayBasic status messages are displayed here.

[INTERRUPT] key display areaWhen interrupt copy is available, the [INTERRUPT]key will be displayed here. When an interrupt copyjob is being run, a [CANCEL] key will be displayedhere to be used for canceling the interrupt copy job.

Copy quantity displayDisplays the selected number of copies before the[START] key is pressed or the number of completedcopies after the [START] key is pressed. A singlecopy can be made when “0” displayed.

[2-SIDED COPY] key (page 9)Touch to display the duplex copy mode settingscreen. A highlighted selection on the screen willindicate the currently selected mode. The settingscreen can be closed by touching the [OK] key onthe setting screen whether or not a selection changewas made.

[OUTPUT] key (page 10)Touch to display the output mode setting screen. Ahighlighted selection on the screen will indicate thecurrently selected mode. The setting screen can beclosed by touching the [OK] key on the setting screenwhether or not a selection change was made.

[SPECIAL MODES] keyTouch to display the special modes selection screen.The functions that can be selected by touching thiskey are described on page 19.

Paper size displayThe display shows the location of the paper trays,the size of the paper in the trays and the approximateamount of paper loaded in each tray. The approximateamount of paper in a tray is indicated by .For changing the paper size in a tray refer to page 1-16 of the “Operation manual (for printer operationand general information)”.

Original size displayThe original paper size will be displayed when originalsare placed on the document glass or in the documentfeeder.

Exposure display and [EXPOSURE] key (page 15)A touch of the [EXPOSURE] key will open theexposure selection window. A highlighted key on theexposure window indicates which exposure mode(AUTO, TEXT, TEXT/PHOTO or PHOTO) is currentlyselected. When an exposure mode other than AUTOis selected, an exposure level scale will also appearin the window.

Paper select display and [PAPER SELECT] key(page 9)Displays the selected paper size. When the autopaper select mode has been selected, “AUTO” willbe displayed.A touch of the [PAPER SELECT] key will open thepaper selection window. When a selection is made,the selection window will close. To close the windowwithout making a selection touch the key again

Copy ratio display and [COPY RATIO] key(page 17)Displays the selected copy ratio.Touch to display the reduction and enlargement copyratio selection screen.

PART NAMES AND FUNCTIONS

SPECIAL MODESORIGINAL

EXPOSUREAUTO

100%

AUTOPAPER SELECT

COPY RATIO

READY TO SCAN FOR COPY.

2-SIDED COPY

OUTPUT

812/ 11x

11 17x

812/ 11x

812/ 11X

812/ 11x

812/ 11x

812/ 11x R

2.1.

3.4.

copy-1_Ep.P65 2/04/01, 19:175

6

AUTOMATIC DOCUMENT FEEDEROriginals set in the automatic document feeder will be automatically fed and copied sequentially.

The automatic document feeder will simultaneously scan both sides of originals when two-sided to one-sided or two-sided to two-sided copying is being done.

Acceptable originalsA stack of up to 50 original sheets of the same size paper can be set in the document feeder tray provided the stackheight is within the limit shown below.A stack of up to 30 mixed size originals can be set if the width of the originals is the same and the stack height is withinthe limit shown below. In this case, however, stapling and duplex will not function and some special functions may notgive the expected result.

Notes on use of the automatic document feeder� Use originals within the specified size and weight ranges. Use of originals out of the specified range may cause

an original misfeed.� Before loading originals into the document feeder tray, be sure to remove any staples or paper clips.� If originals have damp spots from correction fluid, ink or glue from pasteups, be sure they are dried before they

are fed. If not, the interior of the document feeder or the document glass may be soiled.� To prevent incorrect original size detection, original misfeeds or smudges on copies, use the following as a guide

for feeding originals.Transparency film, tracing paper, carbon paper, thermal paper or originals printed with thermal transfer inkribbon should not be fed through the document feeder. Originals to be fed through the feeder should not bedamaged, crumpled or folded or have loosely pasted paper on them or cutouts in them. Originals with multiplepunched holes other than two-hole or three-hole punched paper may not feed correctly.

� When using originals with two or three holes, place them so that the punched edge is at a position other than thefeed slot.

�� Size and weight of acceptable originals �� Total amount of originals that can beset in the document feeder tray

14 lbs. or 50g/m2

22

34 lbs. or 128g/m 2

Original size:

(148 x 210 mm)

5-1/2" x 8-1/2"or A5

11" x 17"or A3

(297 x 420 mm)

Weight (thickness):

g/m ... Weight of a sheet of paper of 1 m

3/16" or 5.0 mm or less

1/4" or 6.5 mm or less

Total aggregate thickness must not exceed 1/4" or 6.5 mm (for 14 to 21 lbs. or 50 to 80 g/m2 paper).

Total aggregate thickness must not exceed 3/16" or 5.0 mm (for 21 to 34 lbs. or 80 to 128 g/m2 paper).

Hole positions

Hole positions

Hole positions

copy-1_Ep.P65 2/04/01, 19:176

7

SETTING ORIGINALS

�� When using the document glass

Open the document cover, place an original facedown on the document glass, and then gentlyclose the document cover.

Original size detector

NOTEDo not place any objects under the original sizedetector, because they may damage it or the originalsize may not be detected properly.

� Set an original by aligning its corner with the tip of thescale ( ) mark at the left rear corner of the glass asshown in the illustrations.

�� When using the automatic documentfeeder

1 Ensure that there is no original on the documentglass.

2 Adjust the original guides to the size of theoriginals.

3 Place the originals face down in the documentfeeder tray.

Set the originals all the wayinto the feed slot. Do notexceed the maximumheight line marked on theoriginal guide.

or B4

Original scalemark

Original scalemark

812/ x11 or A4

812/ x11R or A4R

812/ x14

11x17 or A3or B4

512/ 81

2/xor A5

copy-1_Ep.P65 2/04/01, 19:177

8

�� Standard original setting orientationDescriptions of functions that follow in this manual assume that originals are oriented as shown.

Document feeder tray Document glass

�� Automatic copy image rotation - rotation copyingIf the orientation of the originals and copy paper are different, the original image will be automatically rotated 90°and copied. (When an image is rotated, a message will be displayed.) When enlargement of originals larger than 8-1/2" x 11" or A4 is selected, rotation cannot be done.

[Example]

� This function operates in the auto paper select or auto image mode. (Rotation copying can be disabledwith a key operator program. See page 33.)

Orientation of original Orientation of paper Copy after rotation

Face down Face down

Place originals in the document feeder tray or onthe document glass so that the top of the originalis positioned to the rear side of the machine. Ifnot, staples will be incorrectly positioned andsome special features may not give the expectedresult.

SETTING ORIGINALS

Top

TopTop

BottomBottom

Bottom

Top

Bottom

copy-1_Ep.P65 2/04/01, 19:178

9

NORMAL COPYINGThis section describes the normal copying procedure.

Copying from the automatic document feeder

�� 1-sided copies of 1-sided originals

1 Place the originals in the document feeder tray.(page 7)

2 Ensure that the 1-sided to 1-sided copy mode isselected.

812/ 11x

812/ 11x

812/ 11x

11 17x81

2/ 11x

812/ 11x R

1.2.3.4.

ORIGINAL The one-sided to one-sided mode is selectedwhen no icon for a two-sided mode appears in thedashed area on the display.If the 1-sided to 1-sidedcopy mode is alreadyselected steps 3 to 5 are notneeded.

3 Touch the [2-SIDED COPY] key.

2-SIDED COPY

OUTPUT

4 Touch the [1-sided to 1-sided copy] key.

The [1-sided to 1-sided] keywill be highlighted.

5 Touch the [OK] key.

OK

0

6 Ensure that paper of the same size as theoriginals is automatically selected. (✼Note)

COPY RATIO

AUTOPAPER SELECT

100%

812/ 11X

The selected tray will behighlighted or the message“LOAD xxxxxx PAPER.” willappear. If the message ap-pears, load paper in a pa-per tray or the bypass traywith paper of the requiredsize. Even if the messageabove is displayed, copy-ing can be performed ontothe currently selected pa-per.

(✼Note) The following requirements must be satisfied.� Originals of a standard size (11" x 17", 8-1/2" x 14", 8-1/2"

x 11", 8-1/2" x 11"R, 5-1/2" x 8-1/2", A3, B4, A4, A4R or A5)are set and the auto paper select function is enabled.

TRANSPA812/ 11X

812/ 11X

11 17x

1.

2.

3.

PLAIN

PLAIN

If originals of a size otherthan the sizes above are tobe copied, manually selectthe desired paper size.

Original Copy

copy-1_Ep.P65 2/04/01, 19:179

10

When originals are placed in the document feeder tray, asort icon will appear on the touch panel and the sortcopy mode will be automatically selected. In this case,copies will be delivered as shown in the upper illustrationto the left. For output in the group mode as shown in thelower left illustration, the group mode must be selectedon the output setting screen.

7 Select the desired output mode (see below).

2-SIDED COPY

OUTPUT

The sort mode is the defaultmode. To select the groupmode, touch the [OUTPUT]key, then touch the[GROUP] key on the outputsetting screen, and thentouch the [OK] key on thesetting screen.

8 Use the numeric keys to set the desired numberof copies.

Up to 999 can be set.Use the [C] (clear) key tocancel an entry if a mistakehas been made.

9 Press the [START] key.

If the [C] key is pressedwhile originals are beingscanned, scanning willstop. If copying had alreadystarted, copying andscanning will stop after theoriginal in progress isoutput to the original exitarea. In these cases thecopy quantity will be resetto “0”. If scanning has beencompleted but copying isstill in progress, copying willcontinue.

NOTEThe 1-sided to 1-sided copying mode is set as the defaultin the initial settings. This setting can be changed by a keyoperator program (initial status setting ).

NORMAL COPYING

Five sets of copiesOriginals

Five copies of each originalOriginals

Output modes (sort mode and group mode)[Example] Five sets of copies from three originals

� Sort copy

� Group copy

copy-1_Ep.P65 2/04/01, 19:1710

11

Automatic two-sided copying from the automatic documentfeederA duplex module must be installed for automatic 1-sided to 2-sided or 2-sided to 2-sided copying. A duplex module isnot needed for 2-sided to 1-sided copying.

1. Automatic two-sided copying from one-sidedoriginals

2. Automatic two-sided copying from two-sided

originals

3. Automatic one-sided copying from two-sidedoriginals

1 Place the originals in the document feeder tray.(page 7)


2-SIDED COPY

OUTPUT

3 Select the desired duplex copy mode.

BINCHA

The illustration to the leftshows the screendisplayed when a duplexmodule is installed.

Original Copy

NORMAL COPYING


BINDINGCHANGE

OK

Follow step 6 on page 9 to step 9 on page 10.

The image to be copied onto the second side of 2-sidedcopies can be inverted so that the resultant 2-sided copiesare in the correct orientation for binding at the top. For topbinding, touch the [BINDING CHANGE] key on the 2-sidedcopy selection screen.

copy-1_Ep.P65 2/04/01, 19:1711

12

Copying from the document glassWhen copying originals which cannot be fed from the automatic document feeder such as thick originals, open thedocument cover and copy the originals from the document glass

�� 1-sided copies of 1-sided originals

1 Set an original on the document glass. (page 7)

Original size detector

� Set an original by aligning its corner with the tip of thescale ( ) mark at the left rear corner of the glass as shownin the illustrations.

2 Ensure that the 1-sided to 1-sided copy mode isselected.

ORIGINAL 812/ 11x

812/ 11x

812/ 11x

11 17x81

2/ 11x

812/ 11x R

1.2.3.4.

The one-sided to one-sided mode is selectedwhen no icon for a two-sided mode appears in thedashed area on the display.If the 1-sided to 1-sidedcopy mode is alreadyselected steps 3 to 5 are notneeded.

3 Ensure that paper of the same size as the originalis automatically selected. (✼Note)

COPY RATIO

AUTOPAPER SELECT

100%

812/ 11X

The selected tray will behighlighted or the message“LOAD xxxxxx PAPER.” willappear. If the messageappears, load paper in apaper tray or the bypass traywith paper of the requiredsize. Even if the messageabove is displayed,copying can be performedonto the currently selectedpaper.

(✼Note) The following conditions must be satisfied.� Originals of a standard size (11" x 17", 8-1/2" x 14", 8-1/2"

x 11", 8-1/2" x 11"R, 5-1/2" x 8-1/2", A3, B4, A4, A4R or A5)are set and the auto paper select function is enabled.

TRANSPA812/ 11X

812/ 11X

11 17x

1.

2.

3.

PLAIN

PLAIN

If originals of a size otherthan the sizes above are tobe copied, manually selectthe desired paper size.

Original Copy

NORMAL COPYING

or B4

Original scalemark

Original scalemark

812/ x11 or A4

812/ x11R or A4R

812/ x14

11x17 or A3or B4

512/ 81

2/xor A5

copy-1_Ep.P65 2/04/01, 19:1712

13

4 Select the desired output mode (see below).

2-SIDED COPY

OUTPUT

When a document isdetected on the documentglass, the group mode willbe automatically selected.To select sort copy, touchthe [OUTPUT] key, thentouch the [SORT] key on thedisplayed screen, and thentouch the [OK] key.

NOTEIf you touch the [SORT] or [GROUP] key, its correspondingicon will appear on the touch panel. To change theselection, touch the icon to return the display to the outputsetting screen.

5 Use the numeric keys to set the desired numberof copies.

Up to 999 can be set.Use the [C] (clear) key tocancel an entry if a mistakehas been made.

NORMAL COPYING

When originals are placed in the document feeder tray, asort icon will appear on the touch panel and the sortcopy mode will be automatically selected. In this case,copies will be delivered as shown in the upper illustrationto the left. For output in the group mode as shown in thelower left illustration, the group mode must be selectedon the output setting screen.

Output mode (sort copy and group copy)[Example] Five sets of copies from three originals

�� Sort copy

Five sets of copiesOriginals

6 Press the [START] key.

Replace the original withthe next original and pressthe [START] key. Repeatthis operation until alloriginals have beenscanned.If sort was selected in step4, go to the next step.

7 Touch the [READ-END] key.

PLACE NEXT ORIGINAL. PRESS [START].WHEN FINISHED, PRESS [READ-END].

READ-END

�� Group copy

Five copies of each originalOriginals

copy-1_Ep.P65 2/04/01, 19:1713

14

Automatic two-sided copying from the document glassA duplex module must be installed for automatic 1-sided to 2-sided or 2-sided to 2-sided copying. A duplex module isnot needed for 2-sided to 1-sided copying.

1 Place an original on the document glass.(page 7)


2-SIDED COPY

OUTPUT

3 Touch the [1-sided to 2-sided copy] key.

Original Copy

NORMAL COPYING

The image to be copied onto the second side of 2-sidedcopies can be inverted so that the resultant 2-sided copiesare in the correct orientation for binding at the top. For topbinding, touch the [BINDING CHANGE] key on the 2-sidedcopy selection screen.


BINDINGCHANGE

OK

Follow step 3 on page 12 to step 7 on page 13.

copy-1_Ep.P65 2/04/01, 19:1714

15

EXPOSURE ADJUSTMENTSSelect the exposure mode to be consistent with the type of originals to be copied. The selections are AUTO, TEXT,TEXT/PHOTO and PHOTO.

�� Automatic exposure adjustment

0AUTO

EXPOSURE

The automatic exposuremode is the default initialsetting for this machine. Inthis mode, thecharacteristics of anoriginal being copied are“read” by the exposuresystem, and exposureadjustments are madeautomatically. To select anexposure mode moresuitable for originals to becopied or to adjust theexposure manually, followthe procedure below.

�� Exposure mode selection and manualexposure adjustment

1 Touch the [EXPOSURE] key.

81/ 11XAUTO

0AUTO

EXPOSURE

2 Select [TEXT], [TEXT/PHOTO] or [PHOTO] basedon the original to be copied.

PHOTO

TEXT

TEXT / PHOTO

NOTEExposure mode selectionTEXT: This mode is useful for producing dark

text copies with minimum background.TEXT/PHOTO: This provides the best balance for copying

an original which contains both text andphotos. This mode is also useful forcopying printed photographs.

PHOTO: This mode provides the best copies ofphotographs with fine details.

3 Adjust the exposure level.

1 3 5

Touch the key to makedarker copies. Touch the

key to make lightercopies.

NOTEExposure levels in the text mode

1 to 2: Dark originals such as newspaper3: Normal density originals4 to 5: Originals written with pencils or light color

characters

After adjusting the exposure, follow any of the copyingprocedures.

To return to the automatic exposure mode, touch the[EXPOSURE] key and select [AUTO]. The automaticexposure level can be adjusted using a key operatorprogram. (page 33)

copy-2_Ep.P65 2/04/01, 19:1715

16

REDUCTION/ENLARGEMENT/ZOOMReduction and enlargement ratios can be selected either automatically or manually as described in this section.

� Automatic selection will enlarge or reduce images based upon the original size and copy paper size to give the bestpossible fit of the image to the copy paper.

� Manual selections can be made in the range of 25% to 400%. There are three preset reduction ratios (25%, 64% and77%) and three preset enlargement ratios (121%, 129% and 400%) available for the inch system. There are fourpreset reduction ratios (25%, 70%, 81%, 86%) and four preset enlargement ratios (115%, 122%, 141%, 400%)available for the AB system.

Automatic selection (auto image)The reduction or enlargement ratio will be selected automatically based on the original size and the selected pape size

1 Place the original in the document feeder trayor on the document glass. (page 7)

The detected original size will be displayed.Automatic selection can be used only for 11" x 17", 8-1/2" x 14", 8-1/2" x 11", 8-1/2" x 11"R, 5-1/2" x 8-1/2"size originals and copy paper in the inch system andA3, B4, A4, A4R or A5 in the AB system.

2 Touch the [PAPER SELECT] key and then selectthe desired paper size.

TRANSPA812/ 11X

812/ 11X

11 17x

1.

2.

3.

PLAIN

PLAIN

When the desired papersize key is touched, thepaper size will behighlighted and the papersize setting window will beclosed.If paper of the desired sizeis not loaded in any tray,load paper of the requiredsize in a paper tray andenter the paper size.

3 Touch the [AUTO IMAGE] key.

82 1AUTO

COPY RATIO

PAPER SELEC

AUTOIMAGE

The [AUTO IMAGE] key willbe highlighted and the bestreduction or enlargementratio for the original sizeand the selected papersize will be selected anddisplayed in the copy ratiodisplay.

NOTEIf the message “ROTATE ORIGINAL FROM TO ” isdisplayed, change the orientation of the original asindicated in the message. When the message above isdisplayed, copying can be done without changing theorientation, but the image will not fit the paper correctly.

4 Make all other desired settings such as exposureor the number of copies, and press the [START]key.

When copying from thedocument glass in the sortmode, touch the [READ-END] key after all originalshave been scanned. (step7 on page 13)

To cancel the auto image mode, touch the [AUTO IMAGE]key again to clear the highlighted display.

copy-2_Ep.P65 2/04/01, 19:1716

17

Manual selection


NOTEWhen the document feeder is being used, the availablecopy ratio range is 25% to 200%.

2 Touch the [COPY RATIO] key.

100%COPY RATIO

The preset copy ratio keysfor reduction andenlargement, the keys for[ZOOM] and the [100%] keywill be displayed.

3 Select the desired copy ratio by touching a fixedcopy ratio key for reduction or enlargement andtouch the [OK] key. Use the and keys tomake fine adjustments as needed.

OK

AUTIMAG

10400%25%

121%

129%

64%

77%

100ZOOM

%

11 17x11 17x

812/ 11x

812/ 11x

812/ 14x

11 17x812/ 11x11 17x

812/ 14x

812/ 11x

812/ 14x

812/ 11x

512/ 81

2/x

512/ 81

2/x

If the message “IMAGE ISLARGER THAN THE COPYPAPER.” appears, imageloss will occur. In this caseeither continue with imageloss or change the copypaper size or copy ratio.

4 Ensure that the desired paper size has beenautomatically selected based on the selectedcopy ratio or select another size as needed.P PER SELECT

COPY RATIO77%

If another size paper isselected, the auto paperselect display will becleared.

REDUCTION/ENLARGEMENT/ZOOM

5 Make all other desired settings such as exposureor the number of copies and press the [START]key.


copy-2_Ep.P65 2/04/01, 19:1717

18

SPECIAL PAPERSIf a bypass tray and a duplex module, a duplex module/bypass tray or a multi purpose drawer*1 is installed, specialpapers can be fed. These include transparency film, postcards, labels, envelopes*2, and plain paper.*1 The upper tray of a stand/3 x 500 sheet paper drawer or a stand/MPD & 2000 sheet paper drawer is equivalent to

the multi purpose drawer.

*2 Envelopes can be set in the multi purpose drawer and in the upper tray of a stand/paper drawer.


2 Load the special paper in the bypass tray or inthe multi purpose drawer.

For the paper loading instructions see “Loading paperin the bypass tray” (page 5-3) of the “Operation manual(for printer operation and general information)” or“Loading paper in the multi purpose drawer” (page1-21) of the “Operation manual (for printer operationand general information)”.

3 Touch the [PAPER SELECT] key and then selectthe bypass tray or the multi purpose drawer.

1.

2.

3.

4

COLOR

BYPASS



copy-2_Ep.P65 2/04/01, 19:1718

19

SPECIAL MODEWhen the [SPECIAL MODES] key on the basic screen of the copy mode is touched, the special modes screencontaining six special function touch keys will appear. These functions are shown below.

Common operation procedure for using the special functions

1 Touch the [SPECIAL MODES] key.

SPECIAL MODES

2-SIDED COPY

2 Touch the key for the desired special mode.

MARGIN SHIFT

PAMPHLET COPY

Example:To set the margin shiftfunction:

Setting procedures for modes requiring settingscreens start on the next page. The dual pagecopy and job build functions do not require settingscreens.

MARGIN SHIFT

SPECIAL MODES

PAMPHLET COPY

ERASE

JOB BUILD MULTI SHOT

DUAL PAGECOPY

OK

Margin shift: page 20

Erase: page 21

Dual page copy: page 22

Pamphlet copy: page 23

Job build: page 24

Multi shot: page 25When using the multi shot function, set the original,select the desired paper, and select one-sided ortwo-sided copying before selecting the multi shotfunction on the special modes screen.

[OK] key on the special modes screenTouch the [OK] key, to return to the basic screen ofthe copy mode.

copy-2_Ep.P65 4/26/01, 11:17 AM19

20

Margin shiftThe margin shift function will automatically shift the text or image on the copy paper approximately 1/2" (10 mm) in itsinitial setting.

� The shift direction can be selected from right or leftshift as shown in the illustration.

1 Touch the [MARGIN SHIFT] key on the SPECIALMODES screen.

MARGIN SHIFT

PAMPHLET COPY

The margin shift settingscreen will appear.

2 Select the shift direction.

RIGHT LEFTTouch a shift direction keyto select right or left. Theselected key will behighlighted.

Two-sided copying

Original

One-sided copyingImage shiftedto the right

Image shiftedto the left

Original

Image shiftedto the right

Image shiftedto the left

Margin

Margin

or

Margin

Margin

3 Set the shift amount as needed and touch the[OK] key.

inch1/2 (0 1)

SIDE 2

OK

OKCANCEL

SIDE 1

inch3/8 (0 1)

Use the key and the keys to set the shift amount.The shift amount can beset from 0" to 1" in 1/8"increments ( 0 mm to 20 mmin 1 mm increments for theAB system). If a duplexmodule is not installed, theshift amount setting for thereverse side is notdisplayed.

4 Touch the [OK] key on the special modes screen.After adjusting the exposure, follow any of thecopying procedures.

To cancel the margin shift function, touch the [CANCEL]key on the margin shift setting screen.

SPECIAL FUNCTIONS

copy-2_Ep.P65 2/04/01, 19:1720

21

EraseThe erase function is used to erase the shadow lines on copies produced when copying thick originals or books. Theerase modes that can be selected are shown below. The erase width is approximately 1/2" (10 mm) in it’s initial setting.

Edge eraseEliminates shadow lines around the edges of copiescaused when thick paper or a book is used as an original.

Center eraseEliminates shadow lines produced by the bindings ofbound documents.

Edge + center eraseEliminates shadow lines around the edges of copies andeliminates the shadow at the center of copies.

1 Touch the [ERASE] key on the SPECIAL MODESscreen.

JOB BUILD

ERASE

The erase setting screenwill appear.

2 Select the desired erase mode.

ERASEEDGEERASE

CENTERERASE

EDGE+CENTERERASE

Select one of the threeerase modes. The selectedkey will be highlighted.

3 Adjust the amount of erase and touch the [OK]key.

inch1/2 (0 1)

EDGE

CANCEL OKUse the and keys toadjust the erase width andthen touch the [OK] key.

Original Copy

4 Touch the [OK] key on the special modes screen.After adjusting the exposure, follow any of thecopying procedures.

SPECIAL FUNCTIONS

To cancel the erase function, touch the [CANCEL] key onthe erase setting screen.

copy-2_Ep.P65 2/04/01, 19:1721

22

Dual page copyThe dual page copy function produces separate copies of two documents placed side by side on the document glass.It is especially useful when copying books and other bound documents.

[Example] Copying right and left pages of a book

� The dual page copy function can be used with reductioncopying but cannot be used with enlargement copying.

� The dual page copy function can be done only fromthe document glass. The automatic document feedercannot be used with this function.

� Only 8-1/2" x 11" or A4 paper can be used.

1 Touch the [DUAL PAGE COPY] key on theSPECIAL MODES screen.

MULTI SHOT

DUAL PAGECOPY

The [DUAL PAGE COPY]key will be highlighted.

2 Touch the [OK] key on the special modes screen.

OK

DUAL PAGECOPY

3 Place the originals on the document glass.

Center line of original

Index This page is copied first.

812/ x11 or A4

Dual page copyBook original

When copying book originals:

When copying a thick book, press down lightly onthe document cover.

4 Ensure that 8-1/2" x 11" or A4 size paper isselected.

COPY RATIO

PAPER SELECTAUTO

100%

812/ 11x

If 8-1/2" x 11" or A4 sizepaper is not selected, touchthe [PAPER SELECT] keyto select 8-1/2" x 11" or A4size paper.

After adjusting the exposure, follow any of thecopying procedures. When copying onto two sidesof paper, follow steps 2 to 4 on page 14 and thenfollow steps 4 to 7 on page 13.When copying onto one side of paper, follow steps 4to 7 on page 13.

SPECIAL FUNCTIONS

To cancel the dual page copy function, touch the [DUALPAGE COPY] key on the special modes screen (step 1).(The highlighted display will be canceled.)

NOTETo erase shadows caused by document binding, use theedge erase function (page 21).

copy-2_Ep.P65 2/04/01, 19:1822

23

Pamphlet copyThe pamphlet copy function is used to arrange copies in proper order for eventual center-stapling and folding into abooklet. Two original pages are copied onto each side of copy paper. Four pages are, therefore, copied onto one sheet.

[Example] Copying eight originals in the pamphlet copy mode

1 Touch the [PAMPHLET COPY] key on theSPECIAL MODES screen.

PAMPHLET COPY

The pamphlet copy settingscreen will appear.

2 Designate the type of originals to be copied: 1-sided or 2-sided.

ORIGINAL1-SIDED 2-SIDED

3 Select the binding position (left binding or rightbinding) and touch the [OK] key.

RIGHTBINDING

CANCEL

LEFTBINDING

OK

4 Touch the [OK] key on the special modes screen.

5 Copy from the first page to the last page fromeither the document feeder or the documentglass.

12

34

56

78

7

8

5

6

3

4

1

2

First page

First page

Originals (one-sided)

Originals (two-sided)

Left bindingFor left toright turning

Right bindingFor right toleft turning

Finished copies are folded in two.

6 Ensure that the desired paper size has beenautomatically selected based on the original size.

COPY RATIO

PAPER SELECTAUTO

100%

1711X

To select another sizepaper, select the desiredsize and touch the [AUTOIMAGE] key. Theappropriate copy ratio willbe selected automaticallybased on the original sizeand the paper size. (Seesteps 2 and 3 on page 16.)


8 [When using the automatic document feeder:]Copying will start after all originals have been scanned.(The next step is not needed.)

[When using the document glass:]Replace the original with the next original and pressthe [START] key. Repeat this operation until all originalshave been scanned.

9 Touch the [READ-END] key. (only if the documentglass is used)


READ-END

When the pamphlet copy function is set, the two-sided copying mode will be automatically selectedand cannot be changed.

To cancel the pamphlet copy function, touch the [CANCEL]key on the pamphlet copy setting screen.

SPECIAL FUNCTIONS

� Scan the originals from the first page to the last page.The order of copying will be automatically adjusted bythe machine.

� Either left binding (right to left turning) or right binding(left to right turning) can be selected.

� Four originals will be copied onto one sheet. Blankpages may be automatically produced at the enddepending on the number of the originals.

� When using this function, a duplex module must beinstalled.

� If a saddle stitch finisher is installed, copies can bestapled in two positions along the center of copiesand folded at the center.

copy-2_Ep.P65 2/04/01, 19:1823

24

Job buildThe number of originals that can be copied into a set of copies in a single run is limited by the capacity of the memoryavailable*1 for scanned originals. Normally the number of originals is further limited by the number of originals that canbe set into the document feeder tray*2.The job build function allows scanning and copying of up to 100 originals. For scanning more than 50 originals, theoriginals must be separated into sections not exceeding 50 originals, scanned in sections and stored in memory. Afterall sections are in memory, they can be copied as a continuous set .*1 The number of originals that can be copied into a set of copies in a single run is limited by the capacity of the

memory available for scanned originals.*2 Up to 50 sheets (30 sheets for 8-1/2" x 14" or larger) can be set into the document feeder tray at one time.

[Example] Copying 100 pages of 8-1/2" x 11" or A4 originals

1 Touch the [JOB BUILD] key on the SPECIALMODES screen.

JOB BUILD

The [JOB BUILD] key will behighlighted.

2 Touch the [OK] key on the special modes screenwhile JOB BUILD is highlighted.

OK

ERASE

JOB BUILD

DUAL PAGECOPY

MULTI SHOT

3 Place the first section originals in the documentfeeder tray. (page 7)

Originals

Page 1

50 sheets

Page 51

50 sheets

Divide the originals in sections of 50 sheets and scan the originals starting from the first page of section A and then scan section B. Be sure to keep the correct page order when setting section B.

✽

4 Make all other desired settings such as thenumber of copies, and press the [START] key.

Scanning of originals willstart. After scanning of thefirst section of originals (“Ain the example above) iscompleted, remove thescanned originals, placethe next section of originals(section B in the example)and press the [START] key.Repeat this operation untilall blocks of originals havebeen scanned.

5 Touch the [READ-END] key after the last sectionof originals has been scanned.


READ-END

SPECIAL FUNCTIONS

To cancel the job build function, touch the [JOB BUILD]key on the special modes screen as in step 1. Thehighlighted display will be canceled.

copy-2_Ep.P65 2/04/01, 19:1824

25

Multi shotThe multi shot function is used to copy up to four originals, collectively in a specified order, per sheet of copy paper inany one of four layout patterns.

[Example] Copying seven originals using the 4 in 1 MULTI SHOT selection in a layout pattern starting from the upperleft to lower right.

� When using the multi shot function, place the originals,select the desired paper size, and select the copyingmode (page 9) before selecting the multi shot functionon the special modes screen.

� When using the multi shot function, the appropriatecopy ratio will be automatically set based on the originalsize, paper size, and the number of originals to becopied onto one sheet. The minimum reduction ratiois 25%. Depending on the original size, paper size,and the number of originals to be copied onto onesheet, the appropriate copy ratio may be smaller than25%. In this case, portions of original images may notbe copied.

1 Touch the [MULTI SHOT] key on the SPECIALMODES screen.

MULTI SHOT

The multi shot settingscreen will appear.

2 Select the number of originals to be copied ontoone sheet of copy paper on the multi shotselection screen.

2in1 4in1The orientation of copypaper and the image of theoriginals may be rotated asneeded.

3 Select the layout.

LAYOUT Select the order in whichthe originals will bearranged on the copy.

Copies

One-sided copies from one-sided originals

One-sided copies from two-sided originals

4 [When using the automatic document feeder:]Copying will start after all originals have been scanned.(The next step is not needed.)[When using the document glass:]Replace the original with the next original and pressthe [START] key. Repeat this operation until all originalshave been scanned.

5 If scanning is being done from the documentglass, touch the [READ-END] key after the lastoriginal has been scanned to start copying.


READ-END

To cancel the multi shot function, touch the [CANCEL] keyon the multi shot setting screen.

SPECIAL FUNCTIONS

copy-2_Ep.P65 2/04/01, 19:1825

26

JOB PROGRAM MEMORYFrequently used job programs can be stored in each of ten storage registers. This is convenient for quick job recallwithout losing time manually reprogramming each aspect of a job.

� Selection for functions stored as part of a job program, will not be recalled as part of the program if the function hasbeen disabled or changed by a key operator program.

� To exit the job memory mode, press the [CA] (clear all) key on the operation panel or touch the [EXIT] key on thetouch panel.

Storing a job program

1 Press the [#/P] key on the operation panel todisplay the [STORE/DELETE] selection screen.

2 Touch the [STORE/DELETE] key to obtain thestorage register screen.

5

1

RECALL

M NUMBER.

STORE/DELETE

2 3 4

7 8 9

3 Touch a number key from 1 to 10 on the storageregister screen.

1

6

RECALL

ESS PROGRAM NUMBER.

PROGRAMS

STORE/

2 3 4

7 8 9

Highlighted storageregister numbers areregisters which alreadyhave programs stored. If ahighlighted number isselected, a screen willappear with selections fordeleting the selectedprogram, storing (replacingthe selected program witha new one) or canceling togo back to the STORE/DELETE screen to select adifferent storage register.

4 Make all copier selections to be stored.

TO STORE, MAKE SELECTIONS AND PRESS [OK],TO DELETE, PRESS [CANCEL].

SPECIAL MODES

2-SIDED COPY

OUTPUT

812/ 11X

812/ 11X

812/ 11X

11 17x

812/ 11RX

1.2.3.4.

The number of copiescannot be stored.


EXPOSUREAUTO

AUTO

100%

OK

812/ 11X

11X

812/ 11X

812/ 11X

11 17x

812/ 11RX

1.2.3.4.

D PRESS [OK].

PAPER SELECT

COPY RATIO

CANCEL The selected settings willbe stored under the registernumber selected in step 3.

copy-2_Ep.P65 2/04/01, 19:1826

27

Recalling a job program

Deleting a stored job program

JOB PROGRAM MEMORY

1 Press the [#/P] key.

2 Touch the desired storage register number keyto recall the job from memory.

1

6

2

7

3

8

RECALL

PRESS PROGRAM NUMBER.

JOB PROGRAMS When a number key istouched, the selectionscreen will be closed andthe stored job program willbe recalled. A number forwhich no job program hasbeen stored cannot beselected.

3 Set the number of copies as needed and pressthe [START] key.

Copying will start with thesettings of the recalled jobprogram.

1 Follow steps 1 and 2 in “Storing a job program”on the previous page.

2 Select a storage register number of the programto be deleted.

5

10

3

8

4

9

EXIT

STORE/DELETE

If a number key for whichno job program has beenstored is selected, thescreen will change to thescreen of step 4 on theprevious page (for storinga program). The message“TO STORE, SELECT ANDPRESS [OK]. TO DELETE,PRESS [CANCEL].” willappear. When [CANCEL] ispressed, the screen willreturn to the selectionscreen shown to the left.

3 Touch the [DELETE] key.

REC LL STORE/DELETE

A JOB PROGRAM HAS BEEN ALREADY STORED.STORE ANOTHER PROGRAM?

CANCEL DELETE STORE

When the [DELETE] key istouched, the screen in step2 will return and theprogram will be deleted. Ifthe [CANCEL] key istouched, the screen in step2 will return but the programwill not be deleted. If noother programs are to bedeleted, touch the [EXIT]key on the screen displayedin step 2 to exit the jobprogram mode.

copy-2_Ep.P65 2/04/01, 19:1827

28

INTERRUPTING A PRINT OR COPY RUNINTERRUPT can be used to temporarily stop a long print or copy job so that another copy job can be run. Only copyjobs can be run during interrupt.


2 Touch the [INTERRUPT] key.

ORIGINAL 812/ 11X AUTO

0

AUTO

100%

812/ 11X

INTERRUPT

EXPOSURE

PAPER SELECT

When it is possible tointerrupt a print or copy jobin progress, the[INTERRUPT] key willappear as shown in theillustration.

CANCEL 0AUTO

TO

100%

812/ 11X

EXPOSURE

PER SELECT

ORIGINAL 812/ 11X

When the [INTERRUPT]key is touched in step 2, the[INTERRUPT] touch key willbe replaced by the[CANCEL] key as shown inthe illustration. To cancelinterrupt copying at anytime, touch the [CANCEL]key.

3 Make all other desired settings such as exposure,paper size and number of copies and then pressthe [START] key.

When using the documentglass, replace the originalwith the next original andpress the [START] key.Repeat this operation untilall originals have beenscanned. Then, touch the[READ-END] key.


READ-END

� When step 3 is completed, a copy job icon will appearat the top of the job icon queue at the left side of thescreen and interrupt copying will start. After theinterrupt job is completed, the interrupted job willautomatically resume.

copy-2_Ep.P65 2/04/01, 19:1828

29

MISFEED REMOVALMisfeed in scanner moduleWhen an original has misfed in the scanner module, remove the misfed original following the procedure below.

NOTES� For misfeed removal in the main unit and other peripheral devices, see the “Operation manual (for printer operation and

general information)”.� If you press the [INFORMATION] key, detailed information for misfeed removal will be displayed on the touch panel.

1 Open the document feeding area cover andremove any misfed originals.

Document feeding area cover

2 Close the document feeding area cover.

Close the cover securely sothat cover clicks into place.

3 Open the document cover and turn the greenrotating knob in the direction of the arrow toremove any misfed originals.

4 Close the document cover.

� A message may appear indicating the number oforiginals which must be returned to the documentfeeder tray. Return the originals to the document feedertray and press the [START] key.

copy-2_Ep.P65 2/04/01, 19:1829

30

TROUBLESHOOTINGWhenever the machine stops or operation is not possible, check the operation panel display for messages. In mostcases, these messages will give sufficient information to return the machine to an operating condition. In cases wherethis information is not enough, check the list below for more information. This section describes problems concerningcopier features. For troubleshooting specific problems related to printer, facsimile, or network scanner features, see theseparate manuals provided for them. For problems related to other peripheral devices, see chapter 5 of the “Operationmanual (for printer operation and general information)”.

ProblemMachine does notoperate.

Copies are toodark or too light.

Smudges appearon copies.

Image cannot berotated.

Par t of originalimage is notcopied.

Blank copies

Order of copiesincorrect

Job cancelationneededScanning oforiginals isincomplete.

● Is the START key indicator off?

● Is the original image too dark or toolight?

● Is the exposure mode set to AUTO?

● Is the exposure mode set to PHOTO?● Document glass or document

transport area dirty?

● Black stripes on copies when thedocument feeder is used?

● Original smudged or blotchy?● Is the auto paper select or auto

image function set?

● Is the original positioned correctly?● Is the copy ratio proper for the original

and paper sizes?

● Is the original placed face down?

● Is the order of originals correct?

● Is a message requesting cancelationof job displayed?

● Is a message indicating memory isfull displayed?

Check Solution or causeIf the indicator is not on, the machine may bewarming up. Warm-up should be completed inapproximately 80 seconds.Adjust the exposure in the manual mode. (See page15.)The exposure level in the AUTO mode can beadjusted using a key operator program. Contact yourkey operator. (See page 33.)Cancel the PHOTO exposure mode. (See page 15.)Clean regularly. (See page 4-12 of the “Operationmanual (for printer operation and generalinformation)”.)Clean the original scanning window. (See page 4-12of the “Operation manual (for printer operation andgeneral information)”.)Use a clean original.Rotation copy functions only if the machine is eitherin the auto paper select mode or in the auto imagemode. (See pages 8 and 16.)Set the original properly. (page 7)Use the auto image function to select theappropriate copy ratio based on the original andcopy sizes. (See page 16.)Place the original face down in the document feedertray or on the document glass. (See page 7.)When using the document glass, set the originalsfrom the first page one sheet at a time.When using the automatic document feeder, setthe originals with the first page down.Press the [CA] (clear all) key to cancel the currentjob.If the data amount exceeds the limit when usingthe pamphlet copy or multi shot copy which requiresscanning of all originals, scanning will be canceledand copying will not be performed. If you install ahard disk drive, the storage capacity will increase.

31

SPECIFICATIONSCopier

Resolution Scan: 600 dpi or 300 dpi, output: 600 dpiGradation Scan: 256 levels, output: 2 levelsOriginals Sheets, bound documents

Maximum size: 11" x 17" or A3Copy sizes Max. 11" x 17" or A3, min. 5-1/2" x 8-1/2" or A5

Image loss: Max 21/64" or 8 mm (leading edge), max. 21/64" or 8 mm (side edges)Warm-up time Approx. 80 secondsFirst-copy time* 35 copy/min. type: 5.3 seconds

45 copy/min. type: 4.6 seconds* Paper is fed from paper tray 1, quick scan from document glass (page 33) is set,

the original scanning resolution on the document glass is set to 600 x 300 dpiand no optional hard disk drive is installed.

Copy ratio Variable: 25 to 400% in 1% increments, total 376 stepsFixed presets: 25%, 64%, 77%, 100%, 121%, 129%, and 400% for inch system,25%, 70%, 81%, 86%, 100%, 115%, 122%, 141%, and 400% for AB system

Continuous copy 999 copies; subtractive counter

Scanner moduleName B/W scanner module/DSPFType Two-side simultaneous scanning system from the document feeder.

One-sided scanning from the document glassOriginal feed system Automatic continuous feedingOriginal exit system Face down outputOriginal transport system DSPF: sheet through type (reference position: center), document glass: reference

position is left rearOriginal setting direction Face downOriginal sizes 5-1/2" x 8-1/2" to 11" x 17" or A5 to A3Original weight 14 to 34 lbs. or 50 to 128 g/m2

Capacity Up to 50 sheets (30 sheets for 8-1/2" x 14" or B4 or larger originals) provided thetotal aggregate thickness does not exceed 1/4" or 6.5 mm (14 to 20 lbs. or 50 to 80g/m2) or 3/16" or 5 mm (21 to 34 lbs. or 80 to 128 g/m2)

Power supply Drawn from the main unitDimensions 31-13/16" (W) x 24-3/8" (D) x 7-3/32" (H) or

808 mm (W) x 619 mm (D) x 180 mm (H)Weight Approx. 43 lbs. or 19.5 kg

Copying speed 45 copy/min. type11" x 17" or A3 20 copies/min.8-1/2" x 14" or B4 22 copies/min.8-1/2" x 11" or A4 45 copies/min.8-1/2" x 11"R or A4R 30 copies/min

Copying speed 35 copy/min. type

11" x 17" or A3 17 copies/min.8-1/2" x 14" or B4 20 copies/min.8-1/2" x 11" or A4 35 copies/min.8-1/2" x 11"R or A4R 25 copies/min.

32

KEY OPERATOR PROGRAMSThis section describes all key operator programs relating only to the copier and facsimile functions. For the keyoperator programs which relate to copier, printer and facsimile functions, see the separate Key Operator’s Guide.

Program name Page

Copy function settingsInitial status settings 33Exposure adjustment 33Rotation copy setting 33Auto paper selection setting 33600dpi x 600dpi scanning mode 33Quick scan from document glass 33

Device controlOriginal size detector setting 34Disabling of document feeder 34

Using the key operator programs

To use of the key operator programs, follow the procedures described in the Key Operator’s Guide on page 6. Also read“Supplementary explanation of key operation for key operator programs” on page 6.

Key operator program list

33

Setting programsThis section describes the setting of programs commonto copier, facsimile and network scanning features. Forprograms dedicated to facsimile, network scanning andprograms common to both the copier and printer features,see their respective manuals.

Copy function settingsThe following programs can be set in “Copy functionsettings”.� Initial status settings� Exposure adjustment� Rotation copy setting� Auto paper selection setting� 600dpi x 600dpi scanning mode� Quick scan from document glass

Initial status settingsThe copier settings will be reset when the main switchis turned off, when the [CA] key is pressed or whenthe auto clear interval has elapsed. Use this programto establish new initial settings or to return the initialsettings to the factory default settings. Paper tray,exposure mode, copy ratio, duplex mode, and outputmode default settings can be made.

NOTEIf a duplex mode other than 1-sided to 1-sided is set asthe default and either the duplex or scanner mode isdisabled*, the default will change to the 1-sided to 1-sidedmode.* Disable duplex unit (page 10 of the Key Operator’s Guide)* Disabling of document feeder (page 34)

Exposure adjustmentUse this program to lighten or darken copies in theautomatic exposure mode. The factory setting is “5”.“1” indicates lighter density and “9” indicates darkerdensity on the touch panel.

Rotation copy settingIf this program is set, the image of originals will rotatewhen the orientation of the originals does not matchthat of the copy paper.(Rotation copy will function only if the auto paperselect or auto image mode has been selected.)

NOTEFor copying from 5-1/2 x 8-1/2 or A5 size originals onto 5-1/2 x 8-1/2R or A5R paper, this program must be set.

Auto paper selection settingUse this program to set the paper type* for the autopaper select mode to “Plain paper” or “Plain paperand recycle paper”.* Paper type specified in Tray setting of the custom

setting function (page 1-20 of “Operation manual(for printer operation and general information)”)

600dpi x 600dpi scanning modeUse this program to change the original scanningresolution of the automatic document feeder from600 x 300 dpi to 600 x 600 dpi.If this mode is set, the copy quality for finecharacters and fine lines will be improved but theoriginal scanning speed will be slower.

NOTEIf the original scanning speed is more important than higherresolution, do not set this program.

Quick scan from document glassUse this program to change the original scanningresolution on the document glass from 600 x 600dpito 600 x 300 dpi.If you set this program, the first copy time will beshorter but the copy image will become a little morecoarse.

NOTEIf the copy image quality is more important than first copytime, do not set this program.

KEY OPERATOR PROGRAMS

copy-2_Ep.P65 2/04/01, 19:1833

34

Device control

Original size detection and disabling of the documentfeeder can be set.

Original size detector settingThis program is used to select the group of originalsizes to be detected. Original size detection fromthe document glass can be disabled using theprogram CANCEL DETECTION AT DOCUMENTGLASS.

If CANCEL DETECTION AT DOCUMENT GLASSis set, originals will be regarded as EXTRA for allcopier functions and no original size will be displayed.

Disabling of document feederThis program is used to prevent use of the automaticdocument feeder when the scanner modulemalfunctions. In this case scanning can still be doneoff the document glass.

KEY OPERATOR PROGRAMS

Detectable original sizesGroup Document feeder tray (for automatic document feeding)

Document glass11 x 17, 8-1/2 x 14,

1 INCH - 1 8-1/2 x 11, 8-1/2 x 11R, A45-1/2 x 8-1/211 x 17, 8-1/2 x 13,

2 INCH - 2 8-1/2 x 11,8-1/2 x 11R, A45-1/2 x 8-1/2

3 AB - 1 A3, A4, A4R, A5, 8-1/2 x 11,B4, B5, B5R 216 x 330

4 AB - 2 A3, A4, A4R, A5, 8-1/2 x 11,B5, B5R, 216 x 330 B4

copy-2_Ep.P65 2/04/01, 19:1834

cover4.p65 2/04/01, 19:181

2001D KS1TINSE2077FCZZ

Operation manual for copier

PRINTED IN CHINA

SHARP ELECTRONICS CORPORATION

Sharp Plaza, Mahwah, New Jersey 07430-2135.

SHARP CORPORATION

P350,P450,3500,35013551,4500,4501,4551

cover4.p65 2/04/01, 19:182

Documents

MANUAL DE OPERACION SHARP AR-M450