OPERATING GUIDE

2>>> CONTENTSContents 224-month warranty 6Warranty 6Safety instructions 7The Navigation device 9Operating manual contents 9Use of the product 9Navigation 9

Images* 9Telephone (selected models) 10

Unpacking the Navigation device 10Checking the contents 10Overview of functions 10

Scope of delivery 11Complaints 11Handling the packaging 11

Description of the device 11The basic unit 12Cable for power supply from cigarette lighter 12Battery 12USB connection cable 12Unit bracket 12Accessories 12

Mains power supply unit 12Cable for vehicle integration (for certain models only) 13

Information about the documentation 13

Quick Start Guide 13

Operating instructions 13Registration 13Repairs 13Emissions and disposal 13Overview of the scope of Delivery 14Overview of the navigation device 15General operation 17Maintenance and care 17Battery quality declaration 18Display quality declaration 18Start-up 18Power supply 18

Using the battery 19Connection for the cigarette lighter 19Connection to the mains outlet 20

Connecting to power supply 20TMC antenna (depending on the model) 20GPS antenna 20

Unit antenna 20Cable for vehicle integration (depending on model, optional) 21Cable for rear view camera (depending on the model, optional) 21Memory card 21

Inserting the memory card 22Ejecting the memory card 22

Unit bracket 22Fitting the unit bracket 22

On the windscreen 23

Adjusting the unit holders position 24Attaching the Navigation device 24Removing the Navigation device 24Devices with magnetic holders 24

Switching the Navigation device on/off (model dependent) 24

Switching on 25Switching off (depending on model) 25

Basic information about the touch screen 26

Operation 26Calibration 26

Basic information about the menus 27The main menu 27Entries made with the entry menu 28

Entering characters 28Accepting proposals 28Scrolling through the lists 29Special characters and accent marks 29Other character sets 30Entering numbers 30Switching between upper and lower case: 30Deleting characters 31Inserting spaces 31

The back button 31Content Manager 31

Installing the Content Manager 32Starting the Content Manager 32

Contents

3CONTENTS >>>Transferring pictures 33Faults 34Navigation Mode 35What is navigation? 35Selecting Navigation 36

Home address 36Smart Guess 37

Last destinations list 37The destination list 37Icons used 38

Operating the last destinations list 38Start with existing destination 38Scrolling through stored destinations 38Displaying or editing a destination 38Personal destinations 39Contacts 39

Selecting a destination from Personal destinations 39

Editing Personal destinations 40Selecting a destination from Contacts 40

The New destination menu 41Layout of the New destination menu 42

Enter address 42Select Point of Interest 42Marco Polo City Guides (model dependent) 42Select on map 42Enter geo-coordinates 42Route planning 42

Entering the address 42Selecting a country 43

Selecting an address and starting route guidance 43Entering address by speech (selected models) 48

Live POI Search (model dependent) 49Points of interest 49

Point of interest in the vicinity 50Point of interest near to an address 51Point of interest near to destination 52POI on route 52Entering a point of interest directly 52Calling special destination phone number (depending on the model) 52Additional point of interest information 53

Marco Polo City Guides (model dependent) 53Selecting a destination from the map 53Coordinate entry 55Route planning 56

Simulation of the route 57Creating a new route 57Editing a route 58Optimising a route 59

Navigation settings 59The Map view button 60

Auto zoom 62Select POI categories 62Selecting Info box data fields 623D city view 63

The Route overview button 64The Guidance info button 64The Route options button 66

Selecting the vehicle profile (depending on model) 66Truck and mobile home functions (depending on model) 67Setting truck profiles 68Selecting vehicle category and name 70Selecting the route type 70Time-dependent route guidance 71Avoiding particular types of road 71

The TMC button 71The Traffic Button (model dependent) 72The Voice guidance button 73

Setting the Voice 74Setting the Volume 74

The Warnings button 74Setting Driver alerts 75Setting environmental zones (depending on model) 76Truck warnings (depending on model) 76Setting Speed info 77

The Blocked roads button 78The Vehicle data button 79The Format button 80The Time button 80The Reset button 80

4>>> CONTENTSTraffic announcements using TMC (depending on the model) 81Live Traffic - Traffic Announcements via Data Connection (model dependent) 81

Displaying TMC messages on the map 82Using TMC 82

Reading a message 83Taking announcements into consideration when calculating routes 84

Automatic recalculation 84Manual recalculation 84

The map display 85Calling up the map display 85Structure of the map display 85

Map display without route guidance 85Map display with route guidance 85The Information box 86Split screen with route guidance 87Route guidance with arrow display 88Lane Assistant Pro 3D (model dependent) 88Map display with Junction view 88Tunnel view 89

Using the map display 89Repeating the last announcement 89Changing the announcement volume 90Map zooming 90Moving the map 91Map orientation 91

The Route overview 92

SituationScan 93The detour assistant 93The Park Assistant 93The departure assistant 93

Map display options 94Displaying the whole route 94Move route 95Selecting alternative routes 96Change route options 97Canceling route guidance 97Entering/deleting a stopover 97Blocking route temporarily 98Setting day/night display 99Displaying current position (Where am I?) 99Entering the destination 100Skipping a destination 101

Supplementary functions for trucks and mobile homes (selected models only) 102

Feedback after route calculation 102Zooming in on the map 102Warnings with planned route 102Warnings without planned route 103Show route 103Display height profile 103

Telephone mode 105Calling up the telephone mode (only selected models) 105Telephone menu (only selected models) 106

Dialing a number 106

Phonebook 107Text messages (SMS) (only selected models) 109

Incoming text message 110Number lists 110

Icons used 111Scrolling in the number list 111Dialing an available number 111Displaying or editing entries 111Lists loaded from cell phone 112

Connecting Bluetooth telephones 112Calling up a device list 112Automatic connection 113Searching for cell phones 113Connecting from device lists 114Connecting a mobile phone 114

Disconnecting a connected telephone 115Telephone calls 115

Establishing a call 115Accepting a call 115Ending a call 116During a call 116

Telephone settings 117Bluetooth 118Hands free 118Automatic connection 118Automatic call acceptance 119Telephone volume 119Updating the phonebook 119Bluetooth name 120

5CONTENTS >>>Text message notification (depending on the model) 120

Tools 121Marco Polo City Guides (model dependent) 121Rear View camera 121

Displaying Rear view camera (depending on the model) 121

Image viewer* 122The image viewer menu 122

Selecting an image 123Enlarging the image 123Rotating the picture 123Displaying image information 124

Slide show 124Settings 124Where am I? 124

Traffic forecast (depending on model) 125Country information 125Blocking a section of the road permanently 126Trip computer (depending on model) 128Settings 130Selecting system settings 130

The system settings menu 130Operation 130

Selection options 130Closing the settings menu 130

The individual menu items 131Battery 131Automatic on/off 131Day/night display 132Brightness 132Design by day 133Design by night 133Setting the colour 134Language 134Keyboard layout 135Sounds 135

Rear view camera (depending on the model) 135

Screen animations 135Driver profiles (depending on model) 136

Renaming driver profile 136Deleting driver profile 137Driver profile Pro (model dependent) 137Service information 138Factory settings 138Calibration (model dependent) 138

WiFi settings (model dependent) 139Technical terminology 140index 142Model overview and technical specifications 145NOTICE 146EU Declaration of Conformity 146

Disposal of the unit 147Disposal of the battery 148

Duty to supply information according to battery legislation (BattV) 148

Removing the battery 148

The information and data contained inthese documents are subject to changewithout prior notice.No part of these documents may be du-plicated or transmitted for any purposewhatsoever without express written per-mission of United Navigation GmbH. Alltechnical information, drawings etc. aresubject to copyright law. Copyright 2014, United Navigation GmbHAll rights reserved.

6>>> WARRANTY

24-month warrantyThe company United Navigation GmbH,Marco-Polo-Str. 1, 73760 Ostfildern,Germany, provides a world-wide,24-month warranty (battery: 6 months)for BECKER units, beginning on the dayof delivery to the final customer (buyer).Within the framework of the warranty,functional defects will be eliminatedfree-of-charge, provided that these canbe shown to be the result of material ormanufacturing faults and this shall be ef-fected either by elimination of the fault orby provision of a new unit, at the discre-tion of the manufacturer. Warrantyclaims must be registered by the buyerimmediately after defects are discoveredand must be accompanied by the initialbuyers purchase contract.The warranty expires after 24 months(battery: 6 months); neither warrantyclaims nor fulfilment shall effect an ex-tension of the warranty period.Faults resulting from improper handling,incorrect installation of the unit, impropernoise suppression of the vehicle, staticcharge or mechanical damage are exclud-ed from the warranty.

The warranty is invalidated in the case ofrepairs or tampering on the part of thebuyer or unauthorised third parties.Repairs may only be performed by per-sons and service centres expressly au-thorised by the manufacturer or by themanufacturer himself.This warranty does not affect or restrict the legal warranty rights of the buyer.

Warranty

7SAFETY INSTRUCTIONS >>>Safety instructions

Safety instructions Use of the device is only permitted if the traffic conditions are suitable and you are absolutely sure that its use presents

no risk, distraction or inconvenience to you, your passengers or other road users.Traffic laws and regulations will apply in each and every case. Destinations may only be entered when the vehicle isstationary.

The navigation system is merely an aid, data/information may in select cases be incorrect. The driver must decide in eachsituation by him- or herself if he or she will follow the directions. No liability will be assumed for incorrect directionsprovided by the navigation system. Imprecise or incorrect directions may be provided due to changing traffic patterns ordeviations in data. Therefore, you must always observe the actual road signs and traffic regulations. In particular, thenavigation system must not be used as an orientation aid at times of poor visibility.

The device must only be used for its intended purpose. The volume of the navigation system should be adjusted so thatnoises external to the vehicle are still well audible.

Turn the unit off immediately if a defect occurs (e.g. emission of smoke or odors).

For reasons of safety and security, the device must only be opened by a professional. In case of needed repair pleaseconsult your dealer.

Navigation devices from Becker could contain magnets. Do not bring them near magnetic data carriers (notebooks) orcards (EC cards, credit cards etc.). These could get damaged or be rendered unusable if brought into contact. Magnets canimpair the function of cardiac pacemakers! Persons with cardiac pacemakers should not carry the device to close to theirbodies.

8>>> SAFETY INSTRUCTIONS

It is forbidden to exceed the supply voltages (Volts) specified for the mains adapter, the motor vehicle charging adapterand the product. In case of non-observance, the product or the charger may be damaged, or the battery may explode.

Do not open the product or the battery under any circumstances. No modifications of the product are permitted, any suchmodification leads to the loss of the operating permission.

Only use original BECKER accessories. This way it is ensured that all relevant provisions will be met and that health risksand damages to the product are avoided. Dispose of the used product or the battery according to the legal regulations ineffect.

Improper use excludes all warranties! The safety instructions are also valid for any original BECKER accessories.

Allowed temperature range: -20 C 60 C storage / 0 C 45 C operation

9THE NAVIGATION DEVICE >>>The Navigation deviceOperating manual contentsThis operating manual contains thedescription of your Becker navigationequipment. This manual contains descriptions fordifferent model versions in a singledocument. Therefore, some of thefunctions described here might not beavailable for your equipment undercertain circumstances. All pictures are similar.

Use of the productThis product is a high performance PND(Personal Navigation Device) for use invehicles. Protect the product and theaccessories from moisture and dirt.

NavigationThe use of the GPS = Global Positioningsystem eliminates the tedious processof looking in street maps.The receiver antenna integrated into theproduct allows constant access to thenavigation services outside buildings.Within buildings, it is currently notpossible to access any navigationfunctions. When using in vehicles, itmight not possible to receive sufficentGPS data depending on the installationposition of the Navigation device.

Images*The Navigation device has a PictureViewer with a lot of image displayfunctions.

*depending on model, must be activated via the Content Manager

10

>>> THE NAVIGATION DEVICE

Telephone (selected models)Your Navigation device is equipped withBluetooth wireless technology. ViaBluetooth, you may connect to a cellphone equipped with Bluetoothwireless technology.

Your Navigation device can then be usedas a very comfortable hands-free unit.You also have the option to read out theaddress book or phonebook of the cellphone and to read any received shortmessages.

Unpacking the Navigation device

Checking the contentsBefore you start using the Navigationdevice, the scope and condition of thecontents must be thoroughly checked(see also page 14).> Unpack the contents carefully and

check them thoroughly.

Note:Your Navigation device is delivered in astable packaging. If the packaging or itscontents show the signs of seriousdamages, you must not continue tounpack the product. In such case, pleasecontact your dealer.

Overview of functions : standard- : not available : optional

Navigation systemactive.5 CE

BE B00active.5BE B01

active.5BE B02

active.6 CEBE B30

TMC Vehicle integration - - - -Becker OneShot speech control - - - -Speed camera warning Driver warnings - - -Telephone - - - -Trip computer - - - -Environmental zones Truck & Camper Navigation Pro - - -Traffic forecast - - - -Driver profile Pro - - - -Lane assistant Pro 3D Capacitive display - - - -Reversing camera - - - -Connection for vehicle integration - - - -Becker Link2Live - - - -Live Traffic - - - -Live POI Search - - - -

11

THE NAVIGATION DEVICE >>>Scope of delivery

Navigation deviceDevice console with carrier plate(depending on model)USB cableMotor vehicle adapter power supply12/24 V for cigarette lighters withbuilt-in TMC antenna (depending onmodel)

In the case of devices with magneticholders, the carrier plate and caradapter cable form one unit.

ComplaintsIn case of complaints, please consultyour dealer. The equipment may be sentdirectly to United Navigation in itsoriginal packaging.

Handling the packagingKeep the original packaging in a dryplace, at least for the warranty period.

Description of the deviceThe navigation device consists of thebasic unit and the accessories included inthe scope of delivery.For descriptions of the individual parts,see: "Overview of the scope of Delivery" on

page 141

2

3

4

2

12

34

24

Note:The disposal must be performed in aprofessional manner, according to thecountry-specific regulations. Thepackaging must not be combusted.Depending on the country of delivery, itmight be possible to return thepackaging to the dealer.

Note:The basic unit and accessories must notbe opened or modified in any way.

12

>>> THE NAVIGATION DEVICE

The basic unitThe basic unit consists of the completeelectronic unit: Integrated antenna a TMC receiver for receiving traffic

messages (depending on the model), Touchscreen an integrated loudspeaker a microphone (dependingon the

model).On the side of the unit, there are alsovarious connections and ports.You will find more details of the unitunder: "Model overview and technical

specifications" on page 145

Cable for power supply from cigarette lighterThis cable allows the unit to be connect-ed up to the car's cigarette lighter.The power supply must satisfy thefollowing requirements: DC current 12/24 volts

1 amps

BatteryWhen depleted, the integratedrechargeable battery can be rechargedby connecting the Navigation device tothe power supply.For this purpose, connect the unit via acar power adapter to a 12/24 V socket ina vehicle or via the optional mains powersupply unit to the 230 V mains.

USB connection cableWith the USB connection cable provided,it is possible to connect the Navigationdevice to a standard PC with a USBinterface. The integrated flash memoryof the navigation device and a micro SDcard that may eventually be inserted canthen be addressed by the PC like aremovable storage device.

Unit bracketThe Navigation device can be mounted inthe vehicle using the unit bracket.

Accessories

Mains power supply unitThis power supply allows connection ofthe Navigation device to a mains outlet.

Note:You can charge the Navigation devicevia the car charger cable included in thescope of delivery or via the optionallyavailable mains power supply unit.When the Navigation device isconnected to a PC, it is supplied withpower via the PC and does not consumebattery power.

Note:Switch the navigation device completelyoff, see "Devices with magnetic holders"on page 24, before connecting the navi-gation device to the computer.

13

THE NAVIGATION DEVICE >>>The power supply must satisfy thefollowing requirements: Alternating current 100-240 volts

50-60 Hertz

Cable for vehicle integration (for certain models only)With a 4-pin 3.5mm jack cable you canintegrate your Navigation deviceseamlessly into your vehicle. Details ofthe connection can be found under"Cable for vehicle integration (dependingon model, optional)" on page 21.

Information about the documentation

Quick Start GuideThe Quick Start Guide is designed toprovide a brief introduction to operatingyour Navigation device. The mostimportant basic functions of theNavigation device are explained in theQuick Start Guide.

Operating instructionsA comprehensive explanation of theNavigation device functionalities iscontained in these operatinginstructions.

RegistrationYou can register your product using oursoftware service. We will then informyou of any new updates and other news.

Registration is performed in the "ContentManager" - see page 31.

RepairsThe unit must not be opened if damaged.Please contact your dealer.

Emissions and disposalYou will find details on emissions andelectromagnetic compatibility anddisposal in "NOTICE" on page 146.

14

>>> OVERVIEW OF THE SCOPE OF DELIVERY

Overview of the scope of DeliveryScope of delivery1 Basic device PND (Personal Navigation Device)2 USB connection cable3 Unit holder with carrier plate (the design depending on the

model)4 Cable for power supply via the vehicle cigarette lighter (12/

24 Volt) with integrated TMC-antenna (depending on themodel)

In the case of devices with magnetic holders, the carrier plate and car adapter cable form one unit.

1

2

34

3

2 4

15

OVERVIEW OF THE NAVIGATION DEVICE >>>

Overview of the navigation deviceFront of unit with controls and displays1 Back button

Model dependent: either on the left bottom side of thescreen or in the left top corner of the housing.Press = Back function in most applicationsPress and hold = Open the main menu

2 Touch screen showing the main menu selected3 Touch screen key

Press = activates the corresponding key command

4 Microphone (depending on the model, sometimes in theright top corner, too))

1

2

3

4

16

>>> OVERVIEW OF THE NAVIGATION DEVICE

Top of the unit1 ON/OFF switch

Underside of the unit 2 Slot for Micro SD card3 Mini USB connection / connection for power supply4 Connection for reversing camera5 Connection for vehicle integration

1 2 345

Model dependent, the arrangement of the connections can differ on the bottom side of the device.

Top of the unit1 Standby switch (sleep mode)

Underside of the unit 2 Slot for Micro SD card3 Mini USB connection / connection for power supply4 On/Off switch (I/O)

1 2 3 4

(model dependent)

17

GENERAL OPERATION >>>General operationMaintenance and careThe unit is maintenance-free.For proper care, a commerciallyavailable cleansing fluid for electricaldevices may be applied using a softdamp cloth.

Your mobile navigation system wasdesigned and manufactured with greatcare and should be treated with equalcare. You will enjoy your mobile naviga-tion system for a long time to come if youobserve the recommendations listed inthe following: Protect your mobile navigation unit

and the accessories from water and moisture. If your unit has been exposed to moisture, switch it off immediately and disconnect the power supply. Allow to dry at room temperature.

Do not operate your mobile navigation system in a dusty or dirty environment and do not store it in such an environment.

Do not store your mobile navigation system in hot environments. High temperatures can shorten the service life of electronic components in your unit, damage the rechargeable batteries and cause certain plastics to warp or melt.

Do not store your mobile navigation system in cold environments. During operation, when the unit warms up to operating temperature, moisture may form internally, causing damage to electronic components.

Do not drop your mobile navigation system unit, protect it from shocks and do not shake it. Improper handling can damage components within the unit.

Never use corrosive or aggressive chemicals, cleaning solutions or aggressive detergents for cleaning.

All the above information applies equallyto the mobile navigation system, therechargeable battery, the mains charg-ing and car power adapters as well as allaccessories. Should one of these partsnot work properly, please contact yourauthorised dealer.

Danger!Danger to life by electrocution. Always switch off the unit anddisconnect the mains power supplyunit before cleaning the unit, suppliedcomponents, or accessories.

Note:Do not use any aggressive or abrasivesubstances or cloths which maydamage the surface.A micro-fibre cloth is particularlysuitable for the display.The unit must not be exposed to water.

18

>>> GENERAL OPERATION

Battery quality declarationThe capacity of the rechargeable batteryin your mobile navigation systemdecreases with every charging/discharging cycle. Improper storage atexcessively high or low temperaturesmay also cause a gradual deteriorationof capacity. Consequently, the operatingtime may be substantially reduced evenin the case of a fully charged battery.

Display quality declarationIn some cases, for technical reasons, afew discoloured dots (pixels) may bevisible on the display. Some pixels mayalso appear brighter or darker. However,such instances do not represent aproduct flaw.

Start-upOnce the Navigation device has beenunpacked and checked for damage, theunit can be started up. The individualstart-up steps are: connect to power supply. switching on the unit. ensuring antenna reception (if

navigation is desired)

Power supply

Note:You can charge the Navigation devicevia the car charger cable included in thescope of delivery or via the optionallyavailable mains power supply unit.When the Navigation device is connect-ed to a PC, it is supplied with power viathe PC and does not consume batterypower.

19

GENERAL OPERATION >>>

Using the batteryThe internal power supply is via theintegrated rechargeable battery. Therechargeable battery is maintenance-free and does not require any particularcare.You are alerted by a warning messagewhen the battery should be recharged.After the alert, the device can still beused for approximately 10 minutesbefore switching off automatically.

Connection for the cigarette lighter

Connect the power supply via the vehiclebattery and the cable provided for thecigarette lighter as follows:> Grasp the connector of the connection

cable and insert it gently without forceinto the connector socket of thenavigation device up to the stop, or inthe case of a device with an activecradle, on the underside of thesupporting plate. (Model dependent,this step is not required on navigationdevices with magnetic holders)

> Insert the adapter into the cigarettelighter.

Note:Note that if the battery is completelydischarged, it may take up to a minutebefore the device can be switched onagain.

Note:In the event of a defective battery,please contact your authorised dealer.Please do not attempt to remove thebattery yourself.

Note:If the cigarette lighter has recently beenused and is still hot, wait until the lightersocket has cooled down.

Note:When the engine is switched off, thepower supply slowly discharges thevehicle battery via the cigarette lighter! Do not therefore operate the Navigationdevice for long periods with the engineswitched off.To receive TMC messages (dependingon the model), the power supply mustbe connected to the supporting plate inthe case of a device with an activecradle.

20

>>> GENERAL OPERATION

Connection to the mains outlet

Connecting to power supplyConnection to the public mains grid isachieved using the optionally availablemains power supply unit. Pleaseproceed as follows to connect to themains:> Hold the connector and push it all the

way into the connecting socket in theNavigation device without usingexcessive force.

> Insert the plug of the power supply unitinto the socket.

TMC antenna (depending on the model)The supplied TMC antenna is integratedinto the cable for power supply.The TMC antenna runs in parallel withthe the cigarette lighter cable in thedelivered condition. If the TMC reception is poor, you mustremove the cable of the TMC antennafrom the cable for the cigarette lighter. (Model dependent, the cable cannot bedisconnected on navigation devices withmagnetic holders)

GPS antenna

Unit antennaThe GPS antenna is integrated into thehousing.

Danger!Make sure that your hands are not wetand that the power supply unit is dry.Only connect the power supply unit toa permissible mains power supply.

Note:Remove the power supply unit whennot using the Navigation device forlonger periods of time.

Note:The TMC antenna must be installed insuch a way that it does not distract youwhile driving.

Note:The integrated GPS antenna is notsuitable for use in vehicles with anti-glare windows (metalised thermo-glass or metal foil, indicated by thewindow label - SIGLA SOL, SIGLACHROM, SIGLA, KOOL-OF, SUNGATE,etc.) and vehicles with fine-meshedheating wires in the windows.

21

GENERAL OPERATION >>>

Cable for vehicle integration (depending on model, optional)With a 4-pin 3.5mm jack cable you canintegrate your Navigation deviceseamlessly into your vehicle. connect your Navigation device to the

phone mute function of your audio system. If the cable is connected correctly, your audio system will mute the car radio during navigation announcements.

connect your Navigation device to your audio system for output of the audio signal.

> Plug the cable into the designated 3.5socket on the underside of the device.

Cable for rear view camera (depending on the model, optional)You can connect your rear view camerato your navigation device using a 4-pin2.5mm AV cable. Insert the cable into thesocket provided on the back of the basicunit, also see page 16.

You can make the necessary settings inthe chapter Rear View camera onpage 121.

Memory cardYour Navigation device has a slot for amicro SD memory card.As the map data is stored in an internalmemory on the Navigation device, theslot for a micro SD memory card is usedfor updates and for viewing images.The memory card can also be used forsupplementing the map data.

The card slot is located on the bottomside of the device. The card slot is locatedon the left on the underside of the unit.The card slot is equipped with a spring-actuated locking and ejectormechanism.

Note:Once the cable is connected, theloudspeaker of the basic device isswitched off.

GNDVideoAudio-RAudio-L

GNDTelephone Mute:

Audio-RAudio-L

22

>>> GENERAL OPERATION

Inserting the memory card> Remove the memory card from its

packaging without touching or soilingthe contact bar.

> Hold the memory card so that thecontact strip is facing towards the rearof the unit.

> Guide the memory card into the cardslot.

> Exert a little pressure and slide thememory card into the card slot until itsnaps in.

Ejecting the memory cardThe card slot ejects the card so that youcan pull it out with two fingers.> Use your finger to gently press the

memory card against the spring forceinto the card slot and then release it.

The card is ejected.> Remove the memory card and place it

in the packaging while ensuring not totouch contact bar.

Unit bracketThe Navigation device can be attacheddirectly to the windscreen with the unitholder.

Fitting the unit bracket

Note:The Navigation device and unit bracketmust not be exposed to long periods ofdirect sunlight. Temperatures inside thevehicle of +70 C and higher maydamage parts of the bracket.

Note:Fasten the unit holder such that yourfield of vision is not impaired when theNavigation device is installed andensure that the unit is outside thedeployment area of the airbag. Ensure that the electrical connectioncable does not hamper you fromaccessing the vehicle's controls.Clean the attachment surface on thewindscreen to ensure that it is clean andfree of grease. Do not use greasy orsoapy cleaning agents.

23

GENERAL OPERATION >>>

Suction surface Base Lever Fastening screwCarrier plate Release button

Similar to figure, on devices withmagnetic holders no unlocking button ispresent .

On the windscreenThe unit holder can be attached directlyto the windscreen using the suctionmechanism.> Press the carrier plate onto the four

retaining lugs of the unit holder.> Select a suitable spot to attach.> Loosen the fastening screw slightly.> Press the base with its suction

surface against the windscreen.Turn the unit holder such that thecarrier plate is positioned roughly inthe desired viewing direction.

> Press the lever down.The holder has attached itself firmly tothe windscreen. It can now be adjustedwith precision. In order to remove it,operate the lever again.

27

4

3

1

6

123467

4

1

6 3

27

7

42

1

3

3

24

>>> GENERAL OPERATION

Adjusting the unit holders position> Loosen the fastening screws and

until the carrier plate can bemoved without using excessive force.

> Move the carrier plate to therequired position and hold it in thisposition.

> Tighten the fastening screws and sufficiently so that the Navigation

device is held securely in place whenthe vehicle is in motion.

Attaching the Navigation device> Position the Navigation device with the

attachment point on the bottom of thehousing, onto the carrier plate .

> Without using excessive force, pressthe Navigation device onto the carrierplate . The Navigation device locksinto place.

Removing the Navigation devicePress the button on the top of thecarrier plate . This unlocks theNavigation device which can be removedfrom the carrier plate.

Devices with magnetic holdersThe unlocking button is not present.First place the navigation device with theupper mounting point onto the carrierplate and fold down the navigationdevice. The magnet holds the navigationdevice securely on the carrier plate. Toremove the navigation device, first take itoff from the carrier plate at the bottom.

Switching the Navigation device on/off (model dependent)With the ON/OFF switch (I/O) you canswitch the Navigation device on or offcompletely.With the button on the upper side ofthe Navigation device you can switch thedevice to sleep mode or switch it fromsleep mode again.

For devices without the button on theunderside (model dependent): With the

button you can switch the device off,on or to the sleep mode.

45 6

6

45

6

6

76

7

61

2

1

2

1

2

25

GENERAL OPERATION >>>

Switching on> Press the button on the top of the

Navigation device.The unit is switched on. Themanufacturer's logo appears on thetouchscreen.

When the Navigation device is started forthe first time, the language selection isdisplayed automatically.

Using the buttons or the scrollwheel, it is possible to scroll through thelist in the direction of the relevant arrow.

> Press the button for the requiredlanguage.

> The selection is confirmed by pressingOK.

> Then select the desired voice.

A short example announcement is given.> Confirm your selection by pressing the

OK button.

The following prompt appears shortlyafterwards:

> If you agree to the request contained inthis prompt, press the OK button.

Switching off (depending on model)You can switch the unit off at any time.> Press the button on the top of the

Navigation device.The Navigation device switches to sleepmode.> Before finally switching off the naviga-

tion device, press the I/O switch on theunderside of the device to 0.

Note: for models with TTSVoices with a (TTS) tag support the text-to-speech function (e.g. announcingroads and reading out text messages).

Note:Use of the Navigation device is onlypermitted in accordance with thenational road traffic regulationsapplicable at the time.

26

>>> GENERAL OPERATIONFor devices without the I/O switch on theunderside:> Press the switch on the top of the

navigation device for longer than3 seconds to finally switch it off.

Basic information about the touch screenThe Navigation device is fitted with atouch screen.

OperationWhen you touch a button on the touchscreen, the button in question is brieflyshown outlined in red to confirm theselection.If you touch a button that is not active atthe moment, a short signal tone sounds.

CalibrationIf the touch screen starts respondingimprecisely, calibration should beundertaken.The calibration function is started fromthe menu (see also page 132).

Note:We recommend that you place theNavigation device in sleep mode in theevent of short interruptions to operation(of up to a week). This significantly reduces the switch-ontime and the Navigation device finds thesatellites required for navigation muchfaster.If route guidance was active when sleepmode is activated, it is automaticallyresumed if the Navigation device isswitched back on again within approx.4 hours.If the device cannot be switched offanymore or no longer works reliably, itis possible to switch off devices withoutI/O switches completely by pressing thebutton on the top for longer than7 seconds.

Note:To ensure that the display's surface isnot damaged, you may only touch it withyour fingers or a blunt, non-smearingobject.

27

GENERAL OPERATION >>>

Basic information about the menusDuring operations, you are assisted byvarious menus and entry windows.

The main menuThe top menu level is the main menu.The individual applications are startedfrom the main menu.

You will find information about the indi-vidual applications in the correspondingmain chapters.In addition to the individual applications,the main menu also contains furtherinformation and operating options.

You can tell whether a telephone isalready connected by the symbol on thePhone button.

Telephone connectedTelephone not connected

A satellite symbol at the right of thestatus line shows you whether there iscurrently GPS reception or not.

GPS receptionNo GPS reception

If route guidance is already active, thecurrent destination address and a buttonfor cancelling route guidance will bedisplayed between the two rows ofbuttons.

Press the button to cancel routeguidance to the displayed destinationdirectly in the main menu.

21

12

21

12

1

1

28

>>> GENERAL OPERATION

Entries made with the entry menuSome applications require entries to bemade via the entry menu. The entrymenu is operated in a similar way to akeypad.The keyboard layout can be switchedbetween ABC and QWERTZ, see pageKeyboard layout on page 135

The character entered on the keypad isdisplayed in the top line of the entrymenu. The central area is used to entercharacters. Help functions are providedin the right line. Descriptions of how tooperate the menu are provided below.

Entering charactersCharacters are entered by pressing thekeys in the central area.

Once the entry is complete, the processis concluded by pressing the keyand the entry passed on to theNavigation device for processing.When a navigation destination isentered, the Navigation device comparesthe data with the stored data.Only those letters that are still possiblearea vailable for selection. Characters that cannot be selected aredisplayed greyed out.

Accepting proposalsDuring entry, the Navigation devicemakes proposals in the uppermost line.The proposals take into account yourusage habits. For example, if you enterthe city of Hamburg often, then after youenter the letter "H" the proposal"Hamburg" is automatically displayed.If no preferences are known for the letterentered, then cities/locations suitable forthe entry are displayed as proposals.

> To accept the proposal, you may presseither the input field or the button.

29

GENERAL OPERATION >>>Scrolling through the listsIf you have already entered some of theletters of the selection you want, you canuse the selection list to display all thedestinations containing the combinationof letters in question.

> To call up the selection list, press the key.

The selection list appears.

> Press the arrow keys onthe right hand side of the screen toscroll through the list.

> Press the destination you want.The destination is adopted and theselection list is closed.

Special characters and accent marksSpecial characters and accent marks donot have to be used when entering thenames of towns and streets. TheNavigation device will change entriesfrom AE, OE and UE if necessary.> If, for example, you are looking for the

location "Wrzburg", then simply press"WUERZBURG" or "WURZBURG".

Special characters can be useful whennaming destinations and routes.

> In order to switch to the specialcharacters keyboard, press the buttonmarked with an arrow.

The special characters keyboard isdisplayed.

> Enter the desired special character.After you enter a character, the Naviga-tion device automatically switches to thenormal input menu.To exit the special character keypadwithout an entry, press the buttonmarked with the arrow.

Note:The quantity of selection options is dis-played in the form of the number on thebutton. When there are more than 300options, the precise number is not dis-played.In the list, all the entries correspondingto the letters already entered are dis-played. The letters entered are colouredred in the case of the individual entries.

30

>>> GENERAL OPERATIONOther character setsDifferent character sets can be selectedfor the keyboard of the Navigationdevice.

> Press the button marked with anarrow repeatedly until the desiredcharacter set is selected.

Entering numbersSwitch to the numbers keyboard in orderto enter figures.> Press the button.The numbers keyboard is displayed.

> In order to return again to thekeyboard for entering letters, pressthe button marked with an arrow.

Switching between upper and lower case: During free text entry, it is possible toswitch between upper/lower case andthe automatic function.

> Press repeatedly on the button in thetop right-hand corner of the displayuntil the desired method of entry isactivated.

The inscription on the button symbolisesthe method of entry. The button represents

automatic mode. This means that, on entry, the first letter is automatically in upper case and subsequently changes automatically to lower case.

The button represents the entry of upper case letters.

The button represents the entry of lower case letters.

31

GENERAL OPERATION >>>Deleting charactersTo delete the last character, use the backkey.

> To delete the character to the left of thecursor, press the key.

Inserting spacesIf you have an entry with two words, e.g.for names of towns, the words should beseparated by a space.

> To enter a space, press the key.

The back buttonThe button is located on thebottom left of the device.

It has various functions: Depending on the menu context, if

pressed briefly, you will be returned to the previous entry level.

The main menu is displayed by pressing and holding the button.

Content ManagerThe Content Manager is a PC-basedapplication containing a number ofimportant functions to help you managethe content on your Navigation device. With the Content Manager you can: back up the content saved on the

Navigation device to your PC and restore it later to your Navigation device,

download current content from the Internet and install it on the Navigation device.

To use the Content Manager, you willneed the USB cable provided as well as acomputer that meets the followingminimum requirements:

MinimumOperating system Windows XPProcessor 300 MHz clock

frequencyMain memory 256 MBFree storage space 2 GB

32

>>> GENERAL OPERATION

Installing the Content ManagerYou can install the Content Manager onyour computer with the following steps:> Switch the navigation device comple-

tely off, see Devices with magneticholders on page 24.

> Connect the USB interface of the de-vice directly to a USB port of the com-puter using the USB cable supplied.

> Switch on the navigation device.> If the application does not start automati-

cally, please start the file "CONTENT-MANAGER" manually in the folder"Becker_Content_Manager_Setup".

> Select a language from the list andthen click on OK.

> Read the welcome page and click onNext to continue.

> Select the installation folder. A defaultinstallation folder is already specified.To select another folder, either type inthe path name or click on Browse anddefine another folder.

> Click on Install to start the copyingprocedure. Click on Details to see thedetails during copying.

The Content Manager is automaticallystarted immediately after installation.Remove the check mark from the box ifyou do not want this.This completes the installation proce-dure. > Click on Finish to exit the installation

program.

Starting the Content ManagerExecute the following actions to start theContent Manager:> Switch the navigation device comple-

tely off, see Devices with magneticholders on page 24.

> Connect the USB interface of the de-vice directly to a USB port of the com-puter using the USB cable supplied.

Switch on the Navigation device.

After a short time, the Navigation deviceis displayed as a removable storagemedium on the computer.

Note:When you connect the BeckerNavigation device to the PC for the firsttime, the PC installs all the necessarydrivers and then displays the message"Your unit is now ready to use".

33

GENERAL OPERATION >>>> Click on Start > All Programs on the

computer.> Select Becker.> Click on Content Manager.

When the Content Manager is started,the program executes a number of stepsbefore you can start to manage yournavigation software content.Each time the program is called, aconnection is established to the Internetto check whether a new version of theContentManager is available. If a newsoftware version is found, the ContentManager gives you the option ofinstalling it. We recommend that youalways agree to the upgrade, if one isavailable. If a new software version isfound, you have the following options: Click on Yes to accept the new

software version. The new version is downloaded and installed before you can start the Content Manager.

Click on No to start the Content Manager with the version already installed.

If the new version is a critical update, the Exit button will be shown instead of the No button. You must install the new version, otherwise you have to exit the application.

If you have not yet made a backup of thenavigation unit, the Content Manager willask you each time it starts whether youwould like to make a complete or partialbackup copy.

Transferring picturesImages*, music* and videos* can bestored on a separate Micro SD memorycard (not included in the scope ofdelivery) or in the internal memory of theNavigation device in the "Media" folder. Files can be transferred via a card readeror a USB connection.

Note:We recommend that you always createthe backup. Otherwise you will not beable to restore the content in the eventof loss of data.

Note:Switch off the navigation device com-pletely, see Devices with magneticholders on page 24, before connectingthe navigation device to the computer.We recommend that you give files anddirectories self-explanatory names sothat it is simpler to find these again, ifneeded.

*depending on model, must be activated via the Content Manager

34

>>> GENERAL OPERATION

FaultsMalfunctions in the operating system orin the unit are displayed accordingly. Ifthe function you want cannot then beexecuted, you should restart theNavigation device using the On/Offswitch. If the messages reappear or the unitdoesnot function correctly for any otherreason, please contact your local dealer.You can also try to find a solution toyour problem in the FAQ in the Supportarea on the Becker homepage(www.mybecker.com).

Note:Never attempt to open the unit yourself.Please contact your authorised dealer ifyou are unable to remedy the fault.

35

NAVIGATION MODE >>>Navigation ModeWhat is navigation?The term "navigation" (lat. navigare = totravel by sea) is generally understood tomean the determination of a vehicleslocation, the determination of itsdirection and its distance from thedesired destination and the requiredroute to get there. Stars, prominentlandmarks, compasses and satellitesetc. are used as navigation tools.With the Navigation device, the locationis determined by the GPS receiver. TheGlobal Positioning System (GPS) wasdeveloped during the 1970s by the USmilitary as a weapons guiding system.GPS is based on a total of 24 satelliteswhich orbit the Earth and transmitsignals. A GPS receiver receives thesesignals and calculates its distance to theindividual satellites based on the signaltravel times, and then determines yourcurrent geographical position.

Signals from at least three satellites arerequired to determine your position;your height above sea level can becalculated if signals are received fromfour or more satellites. The Navigation device determines thedirection and distance from thedestination using a navigation computerand a digital street map held in itsinternal memory.For safety reasons, route guidance isgiven predominantly in spoken form.This is supported by a direction indicatorand a map display on the touch screen.

Safety instructions Road traffic regulations always take

priority. The navigation system is merely an aid, data/information may in select cases be incorrect. The driver must decide in each situation by him- or herself if he or she will follow the directions. No liability will be assumed for incorrect directions provided by the navigation system.

When first put into use it can take up to 30 minutes to fix the position.

Observation of traffic signs and local traffic regulations must always take priority.

Traffic guidance is restricted to passenger vehicles. Special driving recommendations and regulations for other vehicles (e.g. commercial vehicles) are not included.

Destinations may only be entered when the vehicle is stationary.

36

>>> NAVIGATION MODE

Selecting NavigationNavigation mode is called up from themain menu. New destinations can beentered in the menu "New destination".Destinations that have already beenvisited or saved can be selected in themenu My destinations.

> In the main menu, press the button Mydestinations.

Home addressWhen you press the Home button youwill be asked to enter an address if nohome address has yet been entered.

> Press the Yes to enter the address.You can then enter a destination asdescribed under "The New destinationmenu" on page 41.

If you have already entered your homeaddress, you can start route guidance toyour home address in the first line. A home address once entered can bemodified later.In the "My destinations" menu, next tothe Home option press the button.

> Press the Change button to enter anew home address.

The menu for selecting the destinationappears.

Note:If an address is displayed in the loweredge of the main menu, this means thatroute guidance has already been startedto the displayed address.

Note:The menu items Set current positionand Select from last destinations (fastaccess mode) can also be used to selecta destination.

37

NAVIGATION MODE >>>

Here you can set the new home addressfor example using an intelligent textentry field.

Smart GuessThe two addresses that can be selectedwith the button, is a selection of theaddresses last visited. Depending on thetime of day and your current position, thetwo most likely destinations aredisplayed and can be selected directly.

Last destinations listThe last destinations visited and saveddestinations are displayed in the Lastdestinations list and can be selecteddirectly. The menu for enteringdestinations can also be called up usingthe fast access function.

The destination listThe destination list displays, line by line,all destinations available for fast dialling. Each line of the destination list is dividedinto two fields. Each list field is designedas a button. The destination is shown onthe right-hand button and the propertiesof the destination are displayed using theleft icon.

Note:Up to 200 of the most recent destina-tions are automatically stored in thedestination list. If the storage capacity isreached, the oldest destination in the listis automatically deleted to make roomfor each new destination. However, im-portant destinations may be protected.If you select your home address and ithas not yet been defined, you will be re-quested to enter the address.

38

>>> NAVIGATION MODEIcons usedThe following icons are used in thedestination list:

Operating the last destinations list

Start with existing destinationThe existing destinations are listed in thedestinations list. > Press the button for the desired

destination to start route calculation.The calculation begins. When the calculation is complete, themap appears and the route guidancebegins.

Scrolling through stored destinationsUsing the buttons or the scrollwheel, it is possible to scroll through thelist.

Displaying or editing a destinationAny destination stored in fast accessmode can be displayed and edited.> Press the button to the left of the

desired destination.> A selection menu appears.

Icon MeaningThis destination is a standard destination with no special features.This destination is protected. If the destination memory is full, this destination will not automatically be deleted. This can be performed manually, if required.In the case of a protected entry, you can also determine the position using the fast access function.

Option MeaningShow details The data for the destina-

tion are displayed. From this screen you can dis-play the destination on the map, display the route or start the route guidance.

Name entry The destination can be renamed. If the destina-tion is given a name it is automatically protected.

Protect entry The destination is pro-tected from automatic deletion. This function is only available for unpro-tected destinations.

39

NAVIGATION MODE >>>Personal destinationsUsing the Personal destinations buttonyou can call up Google points ofinterest that have been imported into theNavigation device and start routeguidance to one. See "Selecting a destination from

Personal destinations" on page 39.

ContactsUsing the Contacts button you can callup Microsoft Outlook contacts thathave been imported into the Navigationdevice and start route guidance to theaddress listed in the contact. See "Selecting a destination from

Contacts" on page 40.

Selecting a destination from Personal destinationsYou can call up Google points of inter-est that have been imported into theNavigation device and start route guid-ance to one.

> In the main menu, press the button Mydestinations.

> Press the Personal destinationsbutton.

Remove protection

The protection is re-moved from the desti-nation. This function is only available for pro-tected destinations.

Move up The destination is moved forwards by one position. If the destina-tion is moved it is auto-matically protected.

Move down The destination is moved back by one po-sition. If the destination is moved it is automati-cally protected.

Delete entry The destination is delet-ed from the fast access mode.

Delete all entries

All destinations (except for the protected desti-nations and your home address) are deleted from the list.

Option Meaning

Note:To display custom Google points ofinterest, the Google KML files mustbe stored in the Navigator\con-tent\userdata\mydest directory of theNavigation device.

40

>>> NAVIGATION MODE

A list of the available destinations will bedisplayed.Using the buttons or the scrollwheel, it is possible to scroll through thelist.

> Select the desired destination.Route guidance to the selecteddestination will be initiated.

Editing Personal destinations> In the list of your own destinations,

press the button in front of thedestination that you wish to edit.

Select Delete entry if you wish to deletethe destination from the list. SelectDelete all entries if you wish to delete theentire list.Select Show details if you wish to displaydetails about the destination.

Press the Start button to begin routeguidance to the destination straightaway.You can also display your chosendestination on the map (On map), store itin fast access mode (Save), display theroute to the destination (Show route) orcall the number if a telephone isconnected and a phone number isavailable by pressing the button with the

symbol.

Selecting a destination from ContactsYou can call up Microsoft Outlook

contacts that have been imported intothe Navigation device and start routeguidance to one.

> In the main menu, press the button Mydestinations.

> Press the Contacts button.

An input menu appears if there are morethan 10 contacts. If there are fewer than

Note:If the list contains numerous entries, itmay be a good idea to search for thedesired destination by selecting Searchentry and using the input menu.A maximum of 1000 destinations can beimported.Newly imported destinations are filed atthe start of the list.

Note: The Microsoft Outlook contacts areimported via the Content Manager.

41

NAVIGATION MODE >>>10 entries, a list of contacts is displayedstraight away.> In the input menu, select the first

letters of the entry you are looking for.> Press the button when the name

you want is displayed in the top line.If there are 5 or fewer entries availablewith the letter combination entered, a listcontaining these entries willautomatically be displayed.

> Select the desired entry in the list.

Press the Start button to begin routeguidance to the address displayed forthis contact straight away.You can also display the address shownfor the contact on the map (On map),store itin fast access mode (Save),display the route to the destination(Show route) or call the numberdisplayed if a phone number is provided(button with the symbol).If there are a number of addressesprovided for the chosen contact, you canselect one of them after pressing thebutton .If there are a number of phone numbersprovided for the chosen contact, you canselect one of them after pressing thebutton .

The New destination menu

> In the main menu, press the buttonNew destination.

The menu for new destinations appears.Note: You may also first have a list displayedthat corresponds to the lettercombination entered. For this purpose,press the button in the inputmenu.

2

1

1

2

42

>>> NAVIGATION MODE

Layout of the New destination menu

Enter addressThe various steps from selecting anaddress to starting route guidance canbe carried out using the Enter addressbutton. See "Entering the address" on page 42.

Select Point of InterestPoints of interest such as airports andferryports, restaurants, hotels, petrolstations or public buildings can beselected and route guidance startedusing the Select Point of Interest button. See "Points of interest" on page 49.

Marco Polo City Guides (model dependent)With the travel guide, you can select, forexample, MARCO POLO Top-Highlightsor MARCO POLO Insider Tips and startthe guide destination there. See "MarcoPolo City Guides (model dependent)" onpage 53.

Select on mapWith the button Select on map, you canselect a destination directly on the mapand start route guidance. See "Selecting a destination from the

map" on page 53.

Enter geo-coordinates The geographic coordinates for adestination can be entered and routeguidance started via the Enter geo-coordinates button. See "Coordinate entry" on page 55.

Route planningA route with several waypoints can beplanned using the Route planningbutton. See "Route planning" on page 56.

Entering the addressThe Enter address button in thedestination input menu opens the menufor entering addresses.

> In the destination input menu, pressthe Enter address button.

The menu for entering addressesappears.

Note: By pressing the Clear form button (topright) you can delete all entered dataapart from the country.

43

NAVIGATION MODE >>>Selecting a countryYou can select a country from thoseavailable using the button for the countryof destination. A country is adoptedautomatically in the address input menuafter selection. If a country of destinationhas already been entered it will remainuntil you select a different country.

> Press the button containing thecountry of destination to access thecountry selection list.

The selection list appears.

> Press the button for the desiredcountry.

Selecting an address and starting routeguidanceYou can enter the exact destinationaddress in the address input menu.

The following settings can be made inthe address input menu: Town Zip code (or postal code) Street and house number Junctions as an orientation aid

It is also possible to: search for a point of interest near to

the address entered (POI search). This can be entered as described under "Point of interest near to an address" on page 51.

save the destination in fast access mode,

show the route on the map. For details please see page 94.

start the route guidance straight away.

Note: If required, press the arrow keys

or use the scroll wheel onthe right of the screen to scroll throughall available countries of destination.The symbol indicates the countriesfor which an address can be enteredusing speech. (depending on the model)

44

>>> NAVIGATION MODESelecting a townThe destination can be entered by eitherusing the name or ZIP code. When you enter the letters of a place, thenavigation device displays suggestions(See "Accepting proposals" on page 28).If you do not want to accept the proposal,just enter the other letters of the locationyou want.The Navigation device excludes allimpossible letter combinations and ZIPcodes and activates only letter fields ornumerical fields that lead to an existinglocation or ZIP code.

> Select the option of entering the townor postcode.

> Enter the letters of the destinationtown or the numbers of the postcodeconsecutively.

When sufficient letters have beenentered it will automatically switch to alist from which you can select the town.However, you can switch to the listbefore this by pressing the button.

Using the town listOnce a few letters of the desired townhave been entered you can display a listof all the towns with the relevant lettercombinations or this list will be displayedautomatically.> Press the button on the right of

the screen to call up the list.

Using the buttons or the scrollwheel, it is possible to scroll through thelist.> Press the button for the required town.

Note:If two words need to be entered youmust separate them with the character

.

Note:If you have entered a postcode, thename of the town will be hidden in theinput menu to start with. If you thenenter the street name, the name of thetown will then also be displayed.

45

NAVIGATION MODE >>>Selecting the streetIn the Street menu field the street andhouse number can be entered separate-ly using a letter and number field. The Navigation device excludes allimpossible letter combinations andactivates only those letters that couldgive an existing street name.A house number can only be chosenonce the street has been selected and ifhouse numbers are included in the data.

> Enter the letters of the destinationstreet consecutively.

When sufficient letters have beenentered it will automatically switch to alist from which you can select the street.However, you can switch to the listbefore this by pressing the button.

Using the street listOnce a few letters of the desired streethave been entered you can display a listof all the streets with the relevant lettercombinations or this list will be displayedautomatically.> Press the button on the right of

the screen to call up the street list.

You can scroll through the displayed listusing the buttons.> Press the button for the desired street.

Selecting the IntersectionAfter entering the destination town andstreet, you can enter a junction so as tofurther limit the choice.

> Press the Intersection button.The input menu for the name of thejunction will appear. > Enter the name of the junction.Once a few letters of the desired streethave been entered a list will automati-cally be displayed.> Press the button for the desired street.

Note: Instead of entering a junction, you canalso enter a house number. However, itis not possible to enter both at the sametime.

46

>>> NAVIGATION MODESelecting a house number After entering the destination town andstreet, you can enter a house number soas to further limit the choice.

> Press the No. button. The input menu for the house numberwill appear. > Enter the house number and then

press the button.

Displaying the routeOnce the address has been entered, theaddress input menu allows the route tothe destination to be displayed on themap.> Press the Show route button to display

the route on the map.The route is calculated.

You can start the route guidance directlyfrom this screen using the Start button.

The other options on this screen aredescribed under "Displaying the wholeroute" on page 94.

Storing a destinationIn the address input menu, the Savebutton opens a menu where a name canbe entered for the specified destination. If the desired name has been enteredand has been pressed to accept it,the destination is transferred to fastaccess mode and protected.

Starting navigationThe Start button starts the routeguidance. All data entered thus far is processedwhen calculating the route.> Press Start to start the route guidance.

The route is calculated. The map willthen be displayed and the route guidancewill begin.

Note: Instead of entering the house number,you can also enter a junction. However,it is not possible to enter both at thesame time.

47

NAVIGATION MODE >>>

If the route guidance is already runningyou will be asked whether the newdestination should replace the olddestination or if the new destinationshould be regarded as a waypoint.

> Select between Add as stopover, Addas new destination or Replace olddestination.

If the route guidance is already runningand a waypoint has already been enteredyou will be asked whether the newdestination should replace the olddestination or the waypoint.

> Select Replace stopover or Replaceold destination.

Note: The symbols above the progress barrefer to restrictions that you may haveactivated (e.g. unpaved roads, tollroads).

Note:If there is no GPS signal when the routeis calculated, the following will bedisplayed:

When a GPS signal is available, the routecalculation will start automatically.When the Last position button ispressed, the last known position is usedand the route calculated from thisposition.

48

>>> NAVIGATION MODEEntering address by speech (selected models)You can start the address input by voicefrom the main menu or address inputmenu by pressing the button.

After pressing the button, a menuthat shows you how to say an addresswill be displayed.

You can say the address as soon as yousee the lines next to the stylised face.

> Say the address.

If your entry is unique, after a short timethe menu for entering addresses will bedisplayed with your entry filled in.

If the address displayed does not matchthe address you said, you can makeappropriate changes.If the address is correct, you can startroute guidance, display the route or storethe address as described on page 46.

Notes: Only one address can be entered

using the voice entry function. Lists for more precise selection cannot be operated using speech.

The destination country cannot be entered using speech.

The symbol in the list of countries indicates the countries for which address entry using speech is possible.If entry using speech is not possible, the button will be displayed greyed out.

An address and the street number must be spoken in the language of the destination country.

Notes: If a number of languages are spoken

in the destination country (as is the case in Switzerland, for example), you can set another language by pressing the Change language button.

You can say the complete address or just a part of it.Possible entries include:- street number - street - town- street - town- town

49

NAVIGATION MODE >>>If your entry was not unique or theNavigation device was not able touniquely assign your entry, you will beshown appropriate lists. You can thenselect the address you want from theselists.Depending on your entry, lists with townnames, lists with street names orcombined lists with town and streetnames can be displayed.

The following example shows a list inwhich a town can be selected.

Entries identified with the symbolopen up a further list when they areselected. This can be necessary if, forexample, the same town name occurs anumber of times in the set country.

Once you have selected the town orstreet you want in the lists, the menu forentering addresses is displayed after ashort time with your entry filled in.You can then start route guidance,display the route or store the address asdescribed on page 46.

Live POI Search (model dependent)With the Live POI Search your Beckernavigation device establishes a connec-tion to our live Server. You have accessto millions of addresses in Europe.You can choose between: A Live POI Search in the vicinity, A Live POI Search near to an address A Live POI Search near to a destinationSubsequent operation is similar to how itis described in the chapter entitled Pointsof interest on page 49, except that nocategories can be selected.

Points of interestPoints of interest (POI) are included in themap and can be displayed there. Pointsof interest include airports and ferryports, restaurants, hotels, petrolstations, public buildings. You can usepoints of interests as navigationdestinations.

Note:Voice entry can be restarted at any timein the lists by pressing the button.

Note:You can only select points of interest inthe area in question if the GPS receptionis adequate for determining a position.Otherwise, the last position stored willbe used.You can extend the places of intereststored on the device by installingadditional POIs in KML format on yourdevice via the Content Manager.

50

>>> NAVIGATION MODE> In the main menu, press the button

New destination.

> Press the Select Point of Interestbutton.

You can choose between: a point of interest in the vicinity, a point of interest near to an address, a point of interest near to a destination, a point of interest along the route or entering a point of interest directly.

Point of interest in the vicinity> Press the POI nearby button.

Press the arrow keys or usethe scroll wheel to scroll through the listdisplayed.> Select one of the available categories.

For some categories, e.g. petrol stations,a further selection menu is displayed inwhich you can narrow down the choicefurther, e.g. by brand.

If you have selected the category, anypoints of interest belonging to therelevant category and available withinthe area in question will now bedisplayed.

The name, distance as the crow flies andthe address is displayed for each entry.Note:

You can also press the All categoriesbutton. An input menu will then openand you can enter the name of a point ofinterest directly and confirm it.

51

NAVIGATION MODE >>>> Select the desired point of interest.

You will now receive additionalinformation about your chosendestination.> Press the Start button to begin route

guidance to the point of interestdirectly.

In addition, the selected point of interestcan be: displayed on the map (On map), saved in fast access mode (Save), used for displaying a route to the POI

(Show route), if a telephone is connected and a

phone number is available by pressing the button with the symbol. (depending on the model)

Point of interest near to an address> Press POI near location.

> Select the desired country.> In the City or Code field, enter the town

where you wish to search for a point ofinterest.

> Press the Select category button.

The available Points of interestcategories for the city entered will bedisplayed.> Select the desired point of interest as

described under "Point of interest inthe vicinity" on page 50.

> Press the Start button to begin routeguidance to the point of interestdirectly.

However, you can also store yourchosenpoint of interest in fast accessmode (Save) or display the route to thepoint of interest (Show route).Note:

If you have already entered an address,this address will appear by default.

Note:Your can also press the Select Point ofInterest button. An input menu will thenopen and you can enter the name of apoint of interest directly and confirm it.

52

>>> NAVIGATION MODEBy pressing of the button next tothe selected POI, you can display theadditionally available information for thedestination.

Point of interest near to destination> Press the POI near destination button.

The categories available near to thedestination are displayed.> Select the desired point of interest as

described under "Point of interest inthe vicinity" on page 50.

POI on route> Press the POI on route buttonThe available Point of Interest categoriesavailable on the whole route will bedisplayed.> Select the desired point of interest on

the route as described under "Point ofinterest in the vicinity" on page 50.

Entering a point of interest directly> Press the POI search by name button.

> Enter the desired point of interest orpart of the name.

> Press the button.The Navigation device displays in a list allthe points of interest corresponding tothe name entered.

> Select the desired destination in thelist.

You will now receive additional informa-tion about your chosen destination.

> Press the Start to begin route guidanceto the point of interest straight away.

However, you can also display yourchosen point of interest on the map (Onmap), store it in fast access mode (Save)or display the route to the point ofinterest (Show route).

Calling special destination phone number (depending on the model)You can dial directly phone numbersspecified in the information on a point ofinterest The prerequisite here is that a cell phoneis connected via Bluetooth with theNavigation device.

> Press the button with the symbolshown at the bottom of the point ofinterest information screen.

The call will be initiated.

53

NAVIGATION MODE >>>Additional point of interest informationAny additional information that isprovided for a point of interest can alsobe displayed.

To display the additional information,press the More button shown at thebottom of the point of interestinformation screen.

You can scroll through the displayed textusing the arrow buttons or the scrollwheel.

Marco Polo City Guides (model dependent)The MARCO POLO travel guide is similarto the function "Enter special destination"(see also page 42).The Marco PoloTravel Guide for Berlin isalready preinstalled. All travel guides areavailable in 5 languages (D, E, I, S, F).Other languages are represented inEnglish. Additional cities can bepurchased from the ContentManager(see also page 31).

Selecting a destination from the mapYou may also select a destination directlyfrom the displayed map.

> Press the Select on map button.The map display appears.

Note:You may need to make the area largerusing the zoom buttons and inorder to find the desired point. You canalso move the map to the desired point.

54

>>> NAVIGATION MODE

> Press the desired point lightly on thesurface of the screen.

A flashing red cross will be displayed atthis point.

> Press the Select button.

Where available, the address of yourchosen point is displayed.> Press the Start button to begin route

guidance to the destination straightaway.

You can also search for points of interestin the vicinity of your chosen point usingthe POI nearby button.However, you can also store yourchosen point in fast access mode (Save)or display the route to the point ofinterest (Show route).

You can select a new destination bytouching the map even during the routeguidance in progress, in order to insert astopover or to replace the olddestination. When touching the display, acompass appears with arrows to adjustthe horizontal display and the verticaldisplay angle of the map. This function isdescribed on page 91.

Note:By pressing the GPS Position you candisplay your current position again.

55

NAVIGATION MODE >>>

Coordinate entry You can also enter your destination usinggeographic coordinates. > In the main menu, press the button

New destination.

> Press Enter geo-coordinates.

> Using select the value you wish tochange.

> Using the two buttons indicated by select the direction required for thegeographic longitude and latitude(east/west or north/south).

> Then enter the desired values usingthe buttons to .

The entry field at the beginning may bedisplayed greyed out. Delete any entriesin the field with the backspace button, inorder to use the entry field. You can entercoordinates in three different ways.The following formats can be used: Degrees Minutes Seconds.Decimal

seconds e.g. 425246.801 Degrees Minutes.Decimal minutes

e.g. 48 53.56667' Decimal degrees e.g. 48.89277778

> Press the button.

Where possible, an address matchingthe coordinates will be displayed. Youcan view the destination on the map,store it, display the route to thedestination or start the route guidancestraight away.

1 2

3

2

1

Notes: The coordinates entered must

correspond to WGS84 (World Geodetic System 1984).

If you press button your current geographic position will be entered into the fields.

3

56

>>> NAVIGATION MODE

Route planningThe route planning menu allows you tocreate and select individual routes. To dothis, enter the individual destinationpoints for the desired route. It is thenpossible to travel to these pointsconsecutively without having to enterany further information. You can alsooptimise the destination points enteredand in so doing change their order.> In the main menu, press the button

New destination.

> Press the Route planning button.In the route menu you can create a newroute by pressing the Create new routebutton. Previously stored routes areshown in a list below this.

Scrolling through stored routes> Press the arrow keys or

use the scroll wheel on the right of thescreen to scroll through the storedroutes.

Editing stored routesYou can add additional stages to a storedroute, change the name of the route ordelete it.> Press the button in front of the

route you wish to edit.

By pressing Add stage you can now adda stage to the route. After pressing Rename route you cangive the route a new name. Pressing Delete route will allow you todelete the route from the stored routes.

Selecting and starting a route> Press a route to select it.The route is loaded and displayed in thestage menu.

> Press the top button.

Note:If no routes have yet been stored, theroute menu is empty.

Note:You can also select a leg of the route.The route is started as of this leg.

57

NAVIGATION MODE >>>

> Select the start point or your currentposition as the start point for routeguidance.

The individual stages are calculated.A map of the stages will then bedisplayed.

> Press the Start button to startguidance for this route.

You can call up the route options usingthe Options button.

Simulation of the routeThere is a play button on the leftunder the map, used to start a simulationof the route.If you touch the display after starting, acontrol bar is displayed at the top withcontrol buttons for the simulation. Youcan pause the simulation with the button, and continue it with the button. The button allows you to fastforward the simulation by a 16x speed.You can move from route section toroute section with the and buttons.If there is no further action, the controlbar disappears after a few seconds.

Creating a new route> Drcken Sie in der Routenplanung die

Taste Create new route.

You can now enter an intermediate des-tination as described under "The Newdestination menu" on page 41 (Enter ad-dress, Select from last destinations, Se-lect Point of Interest, Marco Polo CityGuides, Contacts, Personal destina-tions, Select on map or Enter geo-coor-dinates). You also have the option ofquickly selecting a destination using theSelect from last destinations button.> In the input menu, press the OK button

to accept the relevant intermediatedestination.

Note:If a start point is selected, this is onlyused to view a route.

58

>>> NAVIGATION MODE

> Press Add stage to enter furtherintermediate destinations as describedabove.

> When you have entered all intermedi-ate destinations, press the Donebutton.

> Give the route a name of your choice.The stage menu for the new route will bedisplayed.

Editing a route> Select the route you wish to edit.> Press the button in front of the

stage you wish to edit.

The edit menu will be displayed. Thefollowing options are available:

Notice (depending on model):Here you can define a loading time.This, in turn, has an impact on the calcu-lations of the arrival time for the subse-quent destinations of the route.> Enter the loading time in hours and

minutes using the buttons.If you do not want to set any loadingtime, press the No loading time button.

Option MeaningShow details The data relating to the

intermediate destination is displayed. From this screen, you can display the intermediate destination on the map.

59

NAVIGATION MODE >>>Optimising a routeIf you have entered several destinationsfor a route, you can use the Navigationdevice to optimise the order of thedestinations for the journey distance.The route stored is retained even afteroptimization, however.Call up the map display for the stages ofthe route.

> Press Optimise. The route is optimised and recalculated.

The optimised route is displayed.

Navigation settingsThe navigation settings contain all thesettings that are relevant to thenavigation functions.

> In the main menu, press the button.

> Press the Navigation settings button.

Entering loading time

You can define the ex-pected loading time. This is necessary in or-der to display the most accurate expected arriv-al time possible.

Move up The stage is moved for-wards by one position.

Move down The stage is moved backwards by one position.

Delete stage The stage is deleted from the route.

Replace stage

You can replace the selected stage with another intermediate destination.

Option Meaning

Note:All your settings must be confirmed bypressing the button. Only in a fewcases it is possible to confirm selectionsin the menu using the OK button or theYes button.

60

>>> NAVIGATION MODEThis will take you to the navigationsettings menu.

ConfigurationVarious pages containing functions areavailable in the menu:

You can go to the next or previous pageof the settings by pressing the and

buttons or the scroll wheel.

The Map view buttonYou can select whether the map is to bedisplayed in 3D or 2D mode, in a splitscreen with 3D or 2D display or in arrowmode. You can also select whether or not 3Dbuildings available in towns should bedisplayed in 3D mode.Further setting options are available toyou in the extended settings.

> Press the Map view button in thesettings menu.

The Map view settings window appears.

> Press the button or to selectwhether to use 2D or 3D mode.

> Press the button to select theentire map.

> Press the button for a split screen.1 2 3

54

4 5

1

2

61

NAVIGATION MODE >>>

> Press the button for arrow mode.

To call up the extended settings, pressthe Advanced button.

The following setting options areavailable in the extended settings: Auto zoom

You can select how the map changes when approaching an action point or at different speed.

Select POI categoriesYou can select which symbols are displayed for points of interest on the map.

Infobox data fieldsIn this menu you can define the data to be displayed in the Info box in the top left corner of the map view. You can select between Speed, Speed limit, Time and Height.

3D City modelsYou can select whether or not 3D buildings available in towns should be displayed in 3D mode or not . This option is only available with the 3D view active.

Street names 2D/Street names 3DYou can select whether the street names should be displayed ( ) or not ( ) in 3D or 2D mode.

2D heading upYou can select whether the map should always be orientated to the direction of travel ( ) or to the north ( ) in 2D mode. This option is only available with the 2D view active.

3

62

>>> NAVIGATION MODEAuto zoom> Press the Auto zoom button in the

extended settings.

Pressing the Auto zoom button switchesthe zoom function on ( ) or off ( ).When the zoom function is switched on,you can select whether the autozoomaction should be weak, medium orstrong.

Select POI categoriesYou can select which POI symbols are tobe displayed on the map.> Press the Select POI categories button

in the extended settings.

Selecting Show all POIs displays allpoints of interest on the map.Selecting Show no POIs displays nopoints of interest on the map.Selecting User defined selection andthen pressing the Select POIs buttonallows you to determine for yourself inthe menu which then appears whethereach individual points of interestcategory is displayed or not.

> You can then switch the display ofentire categories on ( ) or off ( ).

After pressing the button beside acategory you can switch subcategories infurther menus on or off.> Confirm all your settings by pressing

the button.

Selecting Info box data fieldsIn this menu you can define the data to bedisplayed in the Info box in the top leftcorner of the map view.> Press the Info box data fields button.

The Info box data field selection windowappears.

63

NAVIGATION MODE >>>

Touch the first field to select one of thep