Upload
sezar23
View
296
Download
8
Embed Size (px)
Citation preview
Please read this operation manual before using the air conditioner.Keep this operation manual for future reference.
SPLIT TYPE ROOM AIR CONDITIONER
OPERATION MANUAL
0010522564
HSU-18HEA13(T3)HSU-18HEA03(T3)
HSU-12HEB03
YKS-09HEA03YKS-12HEA03YKS-18HEA03
HSU-12LEA03HSU-18LEA03HSU-22LEA03HSU-24LEA03
HSU-09LEA03HSU-07LEA03HSU-05LEA03
HSU-12LEA03-WHSU-18LEA03-WHSU-22LEA03-WHSU-13LEA03-T
HSU-10LEA03-THSU-09LEA03-W
HSU-09LEB13-HHSU-12LEB13-HHSU-14LEB13-H
HSU-12LEA13-HHSU-18LEA13-HHSU-12LEA13-FHSU-12LEA13-M
HSU-09LEA13-F
HSU-14LEA13-H
HSU-09LEA13-H
HSU-18LEA13-MHSU-07HEA03HSU-09HEA03
HSU-24HEA03
AMS09H03-N
HSU-22HEA03HSU-18HEA03HSU-12HEA03
AMS12H03-NAMS18H03-NAMS22H03-N
HSU-18HEA03(T3)HSU-18HEA13(T3)
HSU-12HEA03/(BP)HSU-09HEA03/(BP)
PAS18L03-N(T3)HSU-12HEA03/(DB)HSU-09HEA03/(DB)
HSU-09CRA03-T
HSU-12CRA03-T
HSU-18CRA03-T
HSU-18LEA03(T3)HSU-18LEA13(T3)
HSU-09LEA03-NHSU-10LED03-THSU-13LED03-THSU-18LED03-THSU-12HEC03HSU-09HEC03
Contents12-45
76.7CAUTIONS
PARTS AND FUNCTIONSOPERATIONMAINTENANCE
TROUBLE SHOOTING
1
6
5
2
1 4
3
Inlet grille
Inlet
Air Purifying Filter (inside)
Outlet
Horizontal flap
Display board
Outdoor Unit
Signal receiver hole
COOL display
HEAT display
HEALTH display
Dry display4
2
3
1
6
6
7
5
4
2
1 5
3
5
2
1
5
3
6
8
8
14
Parts and FunctionsIndoor Unit
Actual inlet grille may vary from the one shown in the manual according to the product purchased
(adjust up and down air flow Don't adjust it manually)
(adjust left and right air flow)Vertical blade
42 31 65
OUTLET
INLET
CONNECTING PIPING AND ELECTRICAL WIRING
DRAIN HOSE
(If the unit which you purchased has healthy function,follow it.
TIMER OFF displayTIMER ON displaySLEEP display
Remote controller
12
3
5
6789
10
4ON/OFFHEALTH
FAN
MODE
SWING
TIMER
CLOCK
SET SLEEP
LOCK RESET
11
1214
15
16
17
13
18
19
20
21
22
2323
1. Operation mode display
23. HEALTH
. noitcnuf
Operation mode AUTO FANCOOLDRY
Remote controller
Display board
HEAT
2. SWING display3.FAN SPEED display
4. SLEEP display5. LOCK display6. SIGNAL SENDING7.TIMER OFF display8. TIMER ON display9. CLOCK display10. TEMP display11. POWER ON/OFF
Used for unit start and stop.12. MODE
Used to select AUTO run, COOL,DRY,HEAT and
13. FANUsed to select fan speed
14. HOURUsed to set clock and timer
15. SWINGUsed to set auto fan direction.
16. SLEEPUsed to select sleep mode.
17. LOCKUsed to lock buttons and
18. TEMP.SETTINGUsed to select your desired
19. SETUsed to confirm timer and
20. TIMERUsed to select TIMER ON,TIMER OFF,TIMER ON-OFF
21. CLOCKUsed to set correct time
22. RESET
back to normal condition.Used to reset the controller
LO MED HIAUTO
FAN operation
LO, MED, HI, AUTO
setting.
LCD display.
temp.
clock settings.
If not,please ignore.)
If the unit which you purchased has healthy function,follow it.If not,please ignore.
NOTE:Cooling only unit do not have displays and functions related with heating
4
7
Ambient temp.displayWhen receiving the remote control signal,
display the set temperature and in the rest
this room temperature is only for reference.time the room temperature is displayed and
12
3
4
1
2
3
Remove the battery cover;Load the batteries as
illustrated. 2 R-03 batteries, resetting key(cylinder);
Be sure that the loadingis in line with the" + "/"-";
Load the battery,then put on the cover again.
The distance between the signal transmission head and the receiver hole should be within 7m without any obstacle as well.When electronic-started type fluorescent lamp or change-over
so the distance to the indoor unit should be shorter.
wireless telephone is installed in the type fluorescent lamp orroom, the receiver is apt to be disturbed in receivingthe signals,
Note:
Full display or unclear display during operation indicates the ries have been used up.Please change batteries.
If the remote controller can't run normally during operation, reload several minutes later.
batte
remove the batteries and
Remove the batteries in case unit won't be in usage for a long period. If there are any display after taking-out, just need to press reset key
Hint:
Loading of the battery
please
Clock setPress CLOCK button, "AM" or "PM" flashes.Press or to set correct time. Each press
change quickly. After time setting is confirmed,press SET,"AM "and "PM" stop flashing,while clock starts working.
or decrease 1min. If the button is kept pressed,time will
TIMER
CLOCK
SET SLEEP
LOCK RESET
will increase
(inside)Anion generator7
7
Used to operate the healthy
2
Operation Unit start / stop
AUTO LO MED HI
Note:In DRY mode, when room temperature becomes lower than temp.
osetting+2 C, unit will run intermittently at LOW speed regardless
In HEAT mode,warm air will blow out after a short periodof the time
When FAN is set to AUTO, the air conditioner automatically adjusts next time,just press ON/OFF button and unit will run in previous status.Remote controller can memorize each operation status. When starting it
Cooling only unit do not have displays and functions related with heating
Press ON/OFF button, unit starts or stops.
ON/OFF
FAN
HEALTH
FAN
MODE
SWING
According to the automatic choicesystem in temperature in indoors cold or make the hot movement
ON/OFFHEALTH
FAN
MODE
automatically adjusts
1.
2.In FAN operation mode
Auto Operation
Cool Operation
FAN
MODE
SWING
Heat Operation
FAN
MODE
SWING
Dry Operation
FAN
MODE
SWING
Fan Operation
When FAN is set to AUTO, the air conditioner
the fan speed accordingto room temperature.
the unit will not operatein COOL mode but only in FAN mode ,AUTO is not available in FAN mode.And temp.setting is disabled.
of FAN setting.
due to cold-draft prevention function.
the fan speed according to room temperature.
Note:
FAN
MODE
SWING
(1)
Air Flow Direction Adjustm
Select temp.setting FAN
MODE
SWING
Operation Mode
AUTO
Display Board Remote Controller Note
COOL
DRY
HEAT
FAN nothing
In DRY mode, when room temperature becomeslower than temp.setting+2oC,unit will run intermittentlyat LOW speed regardless of FAN setting.
Under the mode of auto operation, air conditioner willautomatically select Cool or Heat operation accordingto room temperature.air conditioner automatically adjusts the fan speed
temperature.
When FAN is set to AUTO, the
according to room
In FAN operation mode, the unit will not operate inCOOL or HEAT mode but only in FAN mode ,AUTO isnot available in FAN mode.And temp.setting is disabled.In FAN mode,SLEEP operation is not available.
HEALTH Operation
ON/OFFHEALTH
FAN
Healthy Negative ions
To cancel TIMER modeJust press TIMER button several times untilTIMER mode disappears.
The anion generator in the airconditioner cangenerate a lot of
the air andalso to kil l bacteria and speed up the dust sediment
anion effectively balance thequantity of position and anion in
in the room and finally clean the air in the room.
OperationPOWER/SOFT Operation
(1) TIMER ON
TIMER
CLOCK
SET SLEEP
TIMER
CLOCK
SET SLEEP
TIMER
CLOCK
SET SLEEP
(2) TIMER OFF
TIMER
CLOCK
SET SLEEP
TIMER
CLOCK
SET SLEEP
You can let unit start or stop automatically a following times:Before you wake up in the morning, or get back from outside
Set Clock correctly before starting Timer operation
(3)
TIMER Operation
TIMER ON-OFF
TIMER
CLOCK
SET SLEEP
TIMER
CLOCK
SET SLEEP
TIMER
CLOCK
SET SLEEP
TIMER
CLOCK
SET SLEEP
or after you fall asleep at night.
Emergency Operation:
temperature is below 16oC, do not use it in the
Test operation:Use this switch in the test operation when the room
normal operation.
your finger from the switch: the cooling
Continue to press the test operation switch for more than 5 seconds. After you hear the "Pi" sound twice,release
Test operation switch is the same as emergency switch.
operation starts with the air flow speed "Hi".
When you need rapid heating or cooling,
You can use this function when silence
In SOFT operation mode, fan speed automatically takes low speed of AUTO fan mode.
Press POWER/SOFT button again ,POWER/SOFT disappears.To cancel SOFT operation
(1) POWER Operation
TIMER
CLOCK
SET SLEEP
POWER/SOFT
(2) SOFT Operation
TIMER
CLOCK
SET SLEEP
POWER/SOFT
you can use this function.
is needed for rest or reading.
Press POWER/SOFT button twice ,POWER/SOFT disappears.To cancel POWER operation
In COOL mode, fan speed automaticallytakes high speed of AUTO fan mode.In HEAT mode, fan speed automatically takes medial speed of AUTO fan mode.
Emergency operation and test operation
Use this operation only when the remote controller is defective or lost.When the emergency operation switch ispressed,the" Pi "sound is heard once, which meansthe start of this operation.In this operation, the system automatically selectsthe operation modes,cooling or fan or heat,accordingto the room temperature.
It is not possible to operate in dry mode.
Room temperature
Operation mode
Designatedtemperature
Timermode Air flow
ABOVE 23OC
BELOW 23OC
COOLING
HEAT 23OC
26OC NO
NO
AUTOMATIC
AUTOMATIC
Pi
(Cooling only uint)Room temperature
Operation mode
Designatedtemperature
Timermode Air flow
BELOW 23OC FAN 26OC NO AUTOMATIC
Pi Pi
(This function is unavailable on some models.) (This function is unavailable on some models.)
3
Before going to bed,you can simply press the SLEEP
button and unit will operate in SLEEP mode and bring
4
Operation Mode1. In COOL,DRY mode
1 hours after SLEEP mode starts, temp. will become 1OC higher than temp. setting. After another 1 hours, temp. rises by 1OC further.The unit will run for further 6 hours then stopsTemp. is higher than temp. setting so that room
temperature won't be too Iow for your sleep.
SLEEP operation startsSLEEP operation stops
Approx.6hrs
1 hr Rises 1OC
Rises1OC
Temp.setting Unit stopIn COOL, DRY mode
1 hr
Power Failure Resume FunctionIf the unit is started for the first time, the compressor will not start running unless 3 minutes have elapsed. When the powerresumes after power failure, the unit will run automatically, and 3 minutes later the compressor starts running.
3.In AUTO mode
corresponding sleep mode adapted to the automatically selected operation mode.
4. In FAN modeIt has no SLEEP function.
can't be set up.After the sleeping function is set
function will be cancelled; the machine will be inthe state of timing-on,if the two modes are set upat the same time,either of their operation time is ended first ,the unit will stop automatically,and
5.
Note to the power failure resume: press the sleep button ten times in five seconds and enter
function after hearing four sounds.And press the sleep button ten times within five seconds and leave this function after hearing two sounds.
When quiet sleeping function is set to 8 hours the quiet sleeping time can not be adjusted.When
2. In HEAT mode1 hours after SLEEP mode starts, temp will become 2 OC lower than temp.setting. After another 1 hours, temp decrease by 2 CO
further. After more another 3 hours, temp.rises by 1 C further. The unit will run forO
SLEEPoperation starts
SLEEPoperation stops
1 hr1 hr
3 hrs3 hrsRises 1OC
Temp.setting Unit stop
In HEAT mode
Decreases 2OC
Decreases 2OC
further 3 hours then stops. Temp. is lower than temp. setting so that room temperaturewon't be too high for your sleep.TIMER
CLOCK
SET SLEEP
The unit operates in corresponding sleep mode
TIMER function is set,the quiet sleeping function
up,if user resets TIMER function, the sleeping
the other mode will be cancelled.
Comfortable SLEEP
Operation
you a sound sleep.
SLEEP Operation
Maintenance
5
For Smart Use of The Air Conditioner
Setting of proper roomtemperature
Close doors and windowsduring operation
If the unit is not to be usedfor a long time, turn off thepower supply main switch.
Use the timer effectively
Use the louvers effectively
Do not block the air inletor outlet
Propertemperature
During cooling operationprevent the penetration ofdirect sunlight withcurtain or blind
OFF
Air Filter cleaningOpen the inlet grille by pulling it upward.Remove the filter.
Clean the filter.
Attach the filter.
Close the inlet grille.
Push up the filter's center tab slightly until it is releasedfrom the stopper, and remove the filter downward.
Use a vacuum cleaner to remove dust, or wash the filter withwater.After washing, dry the filter completely in the shade.
Attach the filter correctly so that the "FRONT" indication isfacing to the front.Make sure that the filter is completelyfixed behind the stopper.If the right and left filters are notattached correctly, that may cause defects.
Remote Controller
Do not use the following for cleaning
Do not use water ,wipe the controller with adry cloth.Do not use glass cleaner or chemicalcloth.
Gasoline,benzine, thinner or cleanser maydamage the coating of the unit.
Hot water over 40OC(104OF) may causediscoloring or deformation.
Wipe the air conditioner by using a soft anddry cloth.For serious stains,use a neutraldetergent diluted with water.Wring the waterout of the cloth before wiping.then wipe offthe detergent completely.
Indoor Body
Once everytwo weeks
1.Open the lnlet Grille
2.Detach the standard air filter
3.Attach Air Purifying Filter
4.Attach the standard air filter(Necessary installation)
5.Close the Inlet GrilleClose the Grille surely
Slide the knob slightly upward to release the filter, then withdraw it.
Put air purifying filter appliances into theright and left filter frames.
Detach old Air Purifying Filter
NOTE:The photocatalyst air purifying filter will be solarized in fixedtime. In normal family, it will be solarized every 6 months.
Prop up the inlet grille by using a small device named grille-support
ATTENTION:The white side of the photocatalyst air purifyingfilter face outside,and the black side face the unit.The green side of the bacteria-killing medium air
and the white side face the unit.
Please keep the bacteria-killing medium air purifying filter inavoid long time directly sunshine
when you stop using it,or its ability of sterilization will bereduced.
The bacteria-killing medium air purifying filter will be used for a long time,no need for replacement. But in the period of using them ,you should remove the dust frequently by
Replacement of Air Purifying Filter
which located in the right side of the indoor unit.
purifying filter face outside,
using vacuum cleaner or flaping them lightly,otherwise ,its performance will be affected.
the cool and dry conditions
(NOTE: Air purifying filter is optional part)
CautionsWARNING
Please call Sales/Service Shop for the Installation.Do not attempt to install the air conditioner by yourself because improper worksmay cause electric shock, fire, water leakage.
Connect the earthcable.
earthing
WARNINGWhen abnormality such as burnt-small found, immediately stop the operation button andcontact sales shop.
OFF
Use an exclusive power sourcewith a circuit breaker
ENFORCEMENT
Connect power supply cordto the outlet completely
Use the proper voltage
Do not use power supply cord in a bundle.
Take care not to damagethe power supply cord.
1.Do not use power supply cord extended or connected in halfway
STRICTENFORCEMENT
STRICT
STRICTENFORCEMENT PROHIBITION
PROHIBITION PROHIBITION
PROHIBITION
Do not start or stop theoperation by disconnecting
Do not channel the air flow directlyat people, especially at infants orthe aged.
Do not try to repair or reconstruct by yourself.
Do not use for the purpose of storage offood, art work, precise equipment,breeding, or cultivation.
CAUTIONTake fresh air occasionally especiallywhen gas appliance is running at thesame time.
PROHIBITIONSTRICT
ENFORCEMENT
Do not operate the switch withwet hand.
PROHIBITION
PROHIBITION
PROHIBITION PROHIBITION
PROHIBITION
Do not install the unit near a fireplaceor other heating apparatus.
Check good condition of theinstallation stand
Do not pour water onto the unitfor cleaning
PROHIBITION
Do not place animals or plants inthe direct path of the air flow
Do not place any objects on orclimb on the unit.
Do not place flower vase or watercontainers on the top of the unit.
Do not insert objects into the airinlet or outlet.
PROHIBITION
PROHIBITION
PROHIBITION
STRICTENFORCEMENT
Check properinstallation of thedrainage securely
the power supply cordand so on.
2.Do not install in the place where there is any possibility of inflammable gas leakage around the unit.3.Do not get the unit exposed to vapor or oil steam.
6
Trouble shooting
7
Before asking for service, check the following first.
NormalPerformanceinspection
Noise is heard
Phenomenon Cause or check points
The system does not restartimmediately.
Smells are generated.
Mist or steam are blown out.
Multiplecheck
Poor cooling
Application temp. range of air conditioner -7oC~43oC.
When unit is stopped, it won't restart
elapsed to protect the system.When the electric plug is pulled out and reinserted, the protection circuit
During unit operation or at stop, a swishing or gurgling noise may
(This noise is generated byrefrigerant flowing in the system.)During unit operation, a crackingnoise may be heard.This noise is
temperature changes.Should there be a big noise from
filter may be too dirty.This is because the system circulates smells from the interior
During COOL or DRY operation,
This is due to the sudden cooling
Is power plug inserted?Is there a power failure?Is fuse blownout?Is the air filter dirty?
Are there any obstacles before
Is temperature set correctly?Are there some doors or
Is there any direct sunlightthrough the window during the
Are there too much heat sourcesor too many people in the room
In dry mode, fan speed can’t be changed.
In DRY mode, when room
than temp.setting+2oC,unit will
regardless of FAN setting.
Maximum: D.B
10.The appliance must be installed on a strong enough support.
9.Young children should be supervised ensure that they do not play with the appliance.
8.The appliance is not intended to use by young children or infirmpersons without supervision.
7.The used batteries should be disposed of properly.6.After installation, the power plug should be easily reached..5.The wiring method should be in line with the local wiring standard.
4.The distance between the indoor unit and the floor should be more than 2m.
3. If the fuse on PC board is broken please change it with a fuse type T. 3.15A/250V.
11.The wiring diagram is attached inside the machine.
2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person.The type of connecting wire is H05RN-F or H07RN-F
Cautions
The machine is adaptive in following situation1.Applicable ambient temperature range:
Cooling
Heating
Indoor
Outdoor
Outdoor
Indoor
Maximum: D.B / W.B 32oC/23oC18oC/14oC43oC/26oC18oC27oC15oC24oC/18oC-7oC/-8oC
Minimum: D.B / W.B
Minimum: D.BMaximum: D.BMinimum: D.BMaximum: D.B / W.BMinimum: D.B / W.B
For: T3
Cooling
Heating
Indoor
Outdoor
Indoor
Outdoor
Maximum: D.B / W.BMinimum: D.B / W.BMaximum: D.B / W.BMinimum: D.BMaximum: D.BMinimum: D.BMaximum: D.B / W.BMinimum: D.B / W.B
29oC/19oC18oC/14oC54oC/24oC18oC27oC15oC24oC/18oC-7oC/-8oC
For: T1
during cooling operation?
cooling operation?(Use curtain)
windows left open?
inlet and outlet?
Normally it should be cleaned every 15 days.
run intermittently at LOW speed
temperature becomeslower
indoor unit may blow out mist.
of indoor air.
air such as the smell of furniture,paint, cigarettes.
air flow in unit operation, air
generated by the casing expandingor shrinking because of
be heard.At first 2-3 minutes afterunit start, this noise is more noticeable.
will work for 3 minutes to protect theair conditioner.
immediately until 3 minutes have
If the fuse of outdoor unit on PC board is broken, please changeit with the type of T. 25A/250V.
Application temp. range of air conditioner -7oC~54oC.T1:T3: