Upload
ahmed-awad
View
28
Download
0
Tags:
Embed Size (px)
DESCRIPTION
Electronics and Instrumentation
Citation preview
3/5/2012 MANF360 Ch.2 Diode Applications ١ of 38
MANF360
Electronics and Instrumentation
CHAPTER 2 Diode Applications
Prof. Ismail Mohammed Hafez
Electronics and Communication Department College of Engineering
Ain Shams University (ASU)
3/5/2012 MANF360 Ch.2 Diode Applications
٢ of 38
Chapter Contents
2.1 Load Line Analysis of Diode Circuits 2.2 Half Wave Rectifier 2.3 Full Wave Rectifier 2.4 Power Supplies 2.5 Diode Clippers 2.6 Diode Clampers 2.7 Zener Diodes 2.8 Digital Logic Circuits
3/5/2012 MANF360 Ch.2 Diode Applications
٣ of 38
2.1 Load Line Analysis of Diode Circuits
• The analysis is performed in a graphical manner, a line can be drawn on the characteristics of the device that represent the applied load. The intersection of the load line with the characteristics will determine operating point or Quiescent Point (Q-Point) of the system.
• Consider the diode circuit shown in Fig. 2.1(a), employing a diode having characteristic shown in Fig. 2.1 (b). Apply KVL to this circuit, we have:
E – VD –VR = 0 or E= VD + IDR Load line equation When VD = 0 gives ID = E / R When ID = 0 gives VD = E • As shown in Fig 2.2, a straight line drawn between the two points
will define the load line. • The point of intersection the load line with the characteristic
determines operating point or Quiescent Point (VDQ and IDQ)
3/5/2012 MANF360 Ch.2 Diode Applications
٤ of 38
2.1 Load Line Analysis (Continued)
Fig. 2.2 Drawing the load line and finding the point of operation
Fig. 2.1 Series diode configuration: (a) circuit; (b) characteristics
3/5/2012 MANF360 Ch.2 Diode Applications
٥ of 38
2.1 Load Line Analysis (Continued) Example 2.1 For the diode circuit shown in Fig. 2.3, if E = 10 V and R = 0.5 kΩ
determine the diode voltage VDQ current IDQ and voltage VR using: a) The load line method. b) The diode piecewise linear equivalent circuit with VD=0.7V and rav=10 Ω. Solution
a) The load line equation is given by: E= VD + IDR When VD = 0 gives ID = E / R = 10/0.5 kΩ = 20 mA When ID = 0 gives VD = E = 10 V • The resulting load line appear in Fig 2.4. The point of intersection
the load line with the characteristic determines operating point as: VDQ = 0.78 V IDQ= 18.5 mA VR = 18.5 x 0.5 = 9. 25 V
b) Replace the diode by its piecewise linear equivalent circuit as shown in Fig. 2.5, we have:
E = VD + ID (rav + R) 10 = 0.7 + ID (10 +500) ID = 9.3/510 = 18.23 mA VR = 9.21 mA x 0.5 k Ω = 9.12 V
3/5/2012 MANF360 Ch.2 Diode Applications
٦ of 38
Example 1.1 Solution (Continue)
Fig. 2.5 The diode circuit including the diode model
2.1 Load Line Analysis (Continued)
Fig. 2.3 (a) A diode circuit (b) characteristics
Fig. 2.4 Load line of Example 2.1
3/5/2012 MANF360 Ch.2 Diode Applications
٧ of 38
2.2 Half-Wave Rectification • The half wave rectifier circuit is shown in Fig. 2.6, Vo has an average value of
particular use in ac to dc conversion process. • Assuming an ideal diode, during the interval t = 0 to T/2, the diode is on or short
circuit, Vo = Vi as shown in Fig. 2.6 (a). • For the interval t = T/2 to T, the diode is off or open circuit, Vo = 0 as shown in
Fig. 2.6 (b).
Fig. 2.6 Half wave rectifier (a) Conduction region (0:T/2); (a) Nonconduction region (T/2:T)
3/5/2012 MANF360 Ch.2 Diode Applications
٨ of 38
2.2 Half-Wave Rectification (Continued)
• The process of removing one half of the input is called half wave rectification. The output is Vo has a net positive area above the axis over a full period and an average value determined by:
Vdc = 0.318 Vm shown in Fig. 2.7 • The effect of using a silicon diode with VT = 0.7 is demonstrated in Fig.
2.8, and the average value of Vo is given by: Vdc = 0.318 (Vm – VT)
Fig. 2.7 Half wave rectified signal Fig. 2.8 Effect of VT on half wave rectified signal
3/5/2012 MANF360 Ch.2 Diode Applications
٩ of 38
2.2 Half-Wave Rectification (Continued)
Example 2.2: For the half wave rectifier circuit shown in Fig. 2.9, if Vm = 20 V, assuming an ideal diode do the following:
a) Sketch the output voltage VO. b) Calculate the dc level of the output. c) Repeat Part (a) and Part (b) when using a silicon diode. Solution (a) Vo is shown in Fig. 2.10 (a), note that the diode will conduct during the
negative part of the input. (b) Vdc = -0.318 Vm = -0.318 x 20 = - 6.36 V (c) Using silicon diode, Vo is shown in Fig. 2.10 (b), and Vdc = -0.318 (Vm – 0.7) = -0.318 x 19.3 = - 6.14 V
Fig. 2.10 (a) Resulting vo; (b) Effect of VK on output Fig. 2.9 Half wave rectifier circuit
3/5/2012 MANF360 Ch.2 Diode Applications
١٠ of 38
2.3 Full-Wave Rectification • The full wave rectifier circuit is shown in Fig. 2.11. Assuming ideal diodes, during
the interval t = 0 < t ≤ T/2, D2 and D3 are conducting “on” while D1 and D4 are “off”, the output Vo = Vi as shown in Fig. 2.12 (a).
• For the negative input T/2 < t ≤ T, D1 and D4 are “on”, while D2 and D3 are “off” the polarity across the load resistance is the same as shown in Fig. 2.12 (b).
• The area above the axis for full cycle is twice that for half wave, therefore the dc level is given by Vdc = 2 (0.318) Vdc = 0.636 Vm as shown in Fig. 2.13.
• If silicon rather than ideal diodes are employed the Vomax = Vm – 2VT, and Vdc = 0.636 (Vm – 2VT)
Fig. 2.11 Full wave rectifier circuit
3/5/2012 MANF360 Ch.2 Diode Applications
١١ of 38
2.3 Full-Wave Rectification (Continue)
Fig. 2.12 Conduction path for (a) positive vi and (b) negative vi.
(b)
(a)
Fig. 2.13 Input and output waveform for a full wave rectifier
3/5/2012 MANF360 Ch.2 Diode Applications
١٢ of 38
It requires: • Two diodes • Center-tapped transformer
Vdc = 0.636(Vm)
2.3 Full-Wave Rectification (Continue)
Fig. 2.14 Center-Tapped full wave Transformer Rectifier
Fig. 2.15 Conduction path for (a) positive vi and (b) negative vi.
(a) (b)
3/5/2012 MANF360 Ch.2 Diode Applications
١٣ of 38
Summary of Rectifier Circuits Rectifier Ideal Vdc Realistic Vdc
Half Wave Rectifier Vdc = 0.318 Vm Vdc = 0.318 (Vm – 0.7)
Bridge Rectifier Vdc = 0.636 Vm Vdc = 0.636 (Vm – 2(0.7))
Center-Tapped Transformer Rectifier
Vdc = 0.636 Vm Vdc = 0.636 (Vm – 0.7)
• PIV (PRV) • Because the diode is only forward biased for one-half of the AC
cycle, it is also reverse biased for one-half cycle. • It is important that the reverse breakdown voltage rating of the
diode be high enough to withstand the peak, reverse-biasing AC voltage. PIV (or PRV) > Vm
• PIV = Peak inverse voltage PRV = Peak reverse voltage • Vm = Peak AC voltage
3/5/2012 MANF360 Ch.2 Diode Applications
١٤ of 38
2.4 The Power Supply Diagram • The block diagram of the power supply is shown in Fig. 2.16. It
consists of of the following modules: 1. Step down transformer which transforms the supply voltage to the
desired low level voltage [e.g. vi = 220 sin(2πx50) to vtrans = 12 sin(2πx50) or from AC 220 V to AC 12 V and the frequency is 50 Hz].
2. Full wave rectifier which rectifies the output of the transformer with voltage amplitude vm in our example vm = 12V. The output from the rectifier section is a pulsating DC with Vdc = 0.636(Vm)
Fig. 2.16 A Power supply block diagram
3/5/2012 MANF360 Ch.2 Diode Applications
١٥ of 38
2.4 Power Supply Diagram (Continued) 3. Capacitor Filter as shown in Fig. 2.17 is connected to the rectifier output
and a dc voltage is obtained across the capacitor. The filter circuit reduces the peak-to-peak pulses to a small ripple voltage.
4. IC Voltage Regulator as shown in Fig. 2.18 is the basic connection of three terminal voltage regulator IC to a load.
Fig. 2.17 Capacitor Filter and its output waveform
Fig. 2.18 Three terminal voltage regulator block
diagram
3/5/2012 MANF360 Ch.2 Diode Applications
١٦ of 38
2.4 Power Supply Diagram (Continued) • The series 78 regulators provide fixed regulated positive voltages from +5
to +24V as given by the manufactureur‘s specification sheets listed in Table 2.1.
• Fig. 2.19 shows on IC, a 7812, is connected to provide voltage regulation of 12 V.
• An unregulated voltage input Vi is filtered by capacitor C1 and connected to the IC’s IN terminal. The IC’s OUT terminal provides a regulated +12 V.
• C2 filters the DC output for any high frequency noise.
5. The Load which could be a mobile phone, computer radio …..etc.
Fig. 2.19 Connection of 7812 voltage regulator
3/5/2012 MANF360 Ch.2 Diode Applications
١٧ of 38
2.4 Power Supply Diagram (Continued) • The series 79 regulators provide fixed regulated negative voltages from -5
to -24V as given by the manufactureur‘s specification sheets listed in Table 2.2.
Table 2.1 Positive regulators in 7900 series
Minimum Voltage [V]
Output Voltage [V]
IC Part #
- 7.3 - 5 7905
- 8.4 - 6 7906
- 10.5 - 8 7908
- 11.5 - 9 7909
- 14.6 - 12 7912
- 17.7 - 15 7915
- 20.8 - 18 7918
- 27.1 - 24 7924
Minimum Voltage [V]
Output Voltage [V]
IC Part #
7.3 + 5 7805
8.3 + 6 7806
10.5 + 8 7808
12.5 + 10 7810
14.6 + 12 7812
17.7 + 15 7815
21.0 + 18 7818
27.1 + 24 7824
Table 2.1 Positive regulators in 7800 series
3/5/2012 MANF360 Ch.2 Diode Applications
١٨ of 38
2.4 Power Supply Diagram (Continued) Example 2.3: Consider a voltage power supply using full wave rectifier and IC
regulator, if the desired output is +5V, do the following: a) Draw the circuit diagram. b) Calculate the voltage amplitude at each node. b) Draw the waveform at each node. Solution a) The circuit diagram is shown in Fig. 2.20 b) Since Vo = 5V, from table 2.1 Vi at node (1) = 7.3 V The rectifier Vm = 7.3 / 0.636 = 11.48. Therefore the transformer used is step down one from 220V to12V
Fig. 2.20 Circuit diagram of +5 V power supply
3/5/2012 MANF360 Ch.2 Diode Applications
١٩ of 38
2.5 Diode Clippers
The diode in a series clipper circuit “clips” any voltage that does not forward bias it. The unbiased series clipper circuit is shown in Fig. 2.21 while the biased series circuit clipper is shown in Fig. 2.22.
2.5.1 Series Clipper
Fig. 2.21 Series unbiased clipper (Ideal diodes)
(a)
(b)
3/5/2012 MANF360 Ch.2 Diode Applications
٢٠ of 38
2.5 Diode Clippers (Continued) 2.5.1 Series Clipper (Continued)
Fig. 2.22 (a) Simple biased series clippers (Ideal diodes)
3/5/2012 MANF360 Ch.2 Diode Applications
٢١ of 38
2.5 Diode Clippers (Continued) 2.5.1 Series Clipper (Continued)
Fig. 2.22 (b) Simple biased series clippers (Ideal diodes)
3/5/2012 MANF360 Ch.2 Diode Applications
٢٢ of 38
2.5 Diode Clippers (Continued)
The diode in a parallel clipper circuit “clips” any voltage that forward bias it. The unbiased parallel clipper circuit is shown in Fig. 2.23 while the biased parallel circuit clipper is shown in Fig. 2.24.
2.5.2 Parallel Clipper
Fig. 2.23 Simple unbiased parallel clippers (Ideal diodes)
(a)
(b)
3/5/2012 MANF360 Ch.2 Diode Applications
٢٣ of 38
2.5 Diode Clippers (Continued) 2.5.2 Parallel Clipper (Continued)
Fig. 2.24 Simple biased parallel clippers (Ideal diodes)
3/5/2012 MANF360 Ch.2 Diode Applications
٢٤ of 38
Example 2.4: determine the output waveform for the network shown in Fig.2.25, assuming an ideal diode for the following inputs:
a) sine wave. b ) square wave.
Fig. 2.25 Series clipper
Fig. 2.26 Input / output waveform for part (a).
2.5 Diode Clippers (Continued)
Solution (a) VO = Vi + 5V For V0 = 0 V => Vi = -5V For Vi more negative than -5V Diode is open circuit For more positive Vi than -5V the diode is short circuit the output waveform shown in Fig.2.26,
3/5/2012 MANF360 Ch.2 Diode Applications
٢٥ of 38
Example 2.4 Solution (Continued) (b) VO = Vi + 5V, for Vi = 20 V => V0 = 25V the diode is short circuit as in Fig. 2.27 (a) For Vi = -10V => V0 = 0V the diode is open
(a) vo at vi = +20 V
(b) vo at vi = -10 V
2.5 Diode Clippers (Continued)
Fig. 2.27 Input / output waveform for part (a).
3/5/2012 MANF360 Ch.2 Diode Applications
٢٦ of 38
Example 2.5: determine the output waveform for the network shown in Fig.2.28, assuming an ideal diode for the following input triangular wave.
Fig. 2.28 Parallel clipper
2.5 Diode Clippers (Continued)
3/5/2012 MANF360 Ch.2 Diode Applications
٢٧ of 38
Example 2.5 Solution For negative cycle: VO = V = 4V The transition state at id =0A and Vd =0V this would be at Vi = V = 4V For the open circuit state Vo = Vi
Input / output waveform is shown in Fig. 2.29
2.5 Diode Clippers (Continued)
Fig. 2.29 Input / output waveform for Example 2.5.
3/5/2012 MANF360 Ch.2 Diode Applications
٢٨ of 38
2.6 Diode Clampers A diode and capacitor can be combined to “clamp” an AC signal to a specific DC level as shown in Fig. 2.30.
Fig. 2.30 Diode clamper circuit.
3/5/2012 MANF360 Ch.2 Diode Applications
٢٩ of 38
Example 2.6: Determine the output waveform for the network shown in Fig. 2.31, assuming an ideal diode for the following input indicated.
2.6 Diode Clampers (Continued)
Fig. 2.31 Diode clamper circuit with indicated input.
3/5/2012 MANF360 Ch.2 Diode Applications
٣٠ of 38
Example 2.6: Solution The diode equivalent circuits and the input / output
waveforms are shown in Fig. 2.32.
2.6 Diode Clampers (Continued)
Fig. 2.32 Input / output waveform for Example 2.6.
3/5/2012 MANF360 Ch.2 Diode Applications
٣١ of 38
2.8 Zener Diodes • The analysis on networks employing Zener diode is similar to that applied to the
analysis of the semiconductor diodes. • First determine of the diode then substitute the appropriate model to calculate
the unknown quantities of the network. • The Zener is a diode operated in reverse bias at the Zener Voltage (Vz). Its
equivalent circuit is shown in Fig. 2.33.
Fig. 2.33 Zener diode equivalent circuit (a) “on’ state and (b) is “off” state
(a) (b)
3/5/2012 MANF360 Ch.2 Diode Applications
٣٢ of 38
2.8 Zener Diodes (Continued) Zener Diode Analysis • The analysis on networks employing Zener diode can be broken down into to
steps as follows: Step #1 Determine the state of the Zener diode by removing it from the network
and calculating the voltage across the resulting open circuit. • Applying step #1 to the network of Fig. 2.34 (a) will result in the network of Fig.
2.34 (b). V is calculated by the application of the voltage divider we get:
Fig. 2.34 (a) Basic Zener diode regulator (b) Determining its state
RR
RV iVV
L
LL +
==
(a) (b)
• If V ≥ VZ, the diode is “on” and the equivalent model of Fig. 2.33 (a) is substituted. • If V < VZ, the diode is “off” and the open circuit equivalent model of Fig. 2.33 (b) is
substituted
3/5/2012 MANF360 Ch.2 Diode Applications
٣٣ of 38
2.8 Zener Diodes (Continued) Step #2 Substitute the appropriate equivalent circuit and solve for the desired
unknowns. • When the Zener diode is “on” state it is replaced by a voltage source as shown
in Fig. 2.35 and the circuit parameters are as follows: VL = VZ
Fig. 2.35 (a) Basic Zener diode regulator (b) Its equivalent circuit
RVV
RV
IandR
VI
LiRR
L
LL
−===
(a) (b)
IR = IZ + IL
IZ = IR - IL
• The power dissipated by the Zener diode is determined by: PZ = VZ * IZ
(b)
3/5/2012 MANF360 Ch.2 Diode Applications
٣٤ of 38
Example 2.7: For the Zener diode network shown in Fig. 2.36, Determine VL, VR, IZ, and PZ for the following cases:
(a) RL = 1.2kΩ (b) RL = 3kΩ
Fig. 2.36 Zener diode network
2.8 Zener Diodes (Continued)
3/5/2012 MANF360 Ch.2 Diode Applications
٣٥ of 38
solution (a) RL = 1.2kΩΩΩΩ Step #1 Determine the state of the Zener diode by removing it from the
network and calculating the voltage across the resulting open circuit as shown in Fig. 3.37.
Vkk
Vk
RR
RVV
L
Li 73.82.11
)16(2.1 =Ω+Ω
Ω=+
= VZ = 10V, V < VZ, Zener diode is “off”
VL= V = 8.73V VR = Vi – VL= 16 - 8.73 = 7.27 V IZ = 0 A and PZ = 0 W
Step #2 Substitute the appropriate equivalent circuit (Zener diode is off ) as shown in Fig. 3.37 (a) and solve for the desired unknowns as follows:
2.8 Zener Diodes (Continued)
Fig. 2.37 (a) Zener diode equivalent circuit
3/5/2012 MANF360 Ch.2 Diode Applications
٣٦ of 38
Vkk
Vk
RR
RVV
L
Li 1231
)16(3 =Ω+Ω
Ω=+
= VZ = 10V, V > VZ, Zener diode is “on”
VL= VZ = 10V
VR = Vi – VL=16 – 10 = 6V
IL = VL/RL = 10V/3kΩ = 3.33 mA
IR = VR /R = 6V / 1 kΩ = 6 mA
IZ = IR – IL = 6 – 3.33 = 2.67 mA PZ = VZ I Z = (10V)(2.67 mA)
= 26.7 mW
2.8 Zener Diodes (Continued) solution (b) RL = 3 k ΩΩΩΩ Step #1 Determine the state of the Zener diode by removing it from the
network and calculating the voltage across the resulting open circuit as:
Step #2 Substitute the appropriate equivalent circuit (Zener diode is voltage source with VZ = 10 V) as shown in Fig. 3.37 (b) and solve for the desired unknowns as follows:
Fig. 2.37(b) Zener diode equivalent circuit
3/5/2012 MANF360 Ch.2 Diode Applications
٣٧ of 38
2.8 Diode Logic Circuit
Fig. 2.38 Logic OR gate circuit
2.8.1 OR Gate as shown in Fig. 2.38
OR gate symbol
3/5/2012 MANF360 Ch.2 Diode Applications
٣٨ of 38
2.8 Diode Logic Circuit (Continued)
Fig. 2.39 Logic AND gate circuit
2.8.2 AND Gate as shown in Fig. 2.39
AND gate symbol