Embed Size (px)
Citation preview
® ®
Positioners for crimp contacts ø 0.5-0.7-0.9 and 1.3 mm
DCE.91.050.0VC DCE.91.050.0VM
These positioners are suitable for use with both manual andpneumatic crimping tools according to the MIL-C-22520/7-01standard.
Connector + Contact
ConductorType AWG
302303 0.5 0.45 1 28-30-32304
Positioners part number
For male For femalecontact contact
male female DCE.91.090.BVM
DCE.91.090.AVC DCE.91.090.AVM
DCE.91.070.BVC DCE.91.070.BVM
DCE.91.050.BVC DCE.91.050.BVM
00.9 0.80 2 22-24-260.9 0.45 2 28-30-320.7 0.80 1 22-24-260.7 0.45 2 28-30-32
306/307 0.5 0.45 1 28-30-32309
DCE.91.131.BVC DCE.91.131.BVM
DCE.91.091.BVC DCE.91.091.BVM
DCE.91.071.BVC DCE.91.071.BVM
DCE.91.051.BVC DCE.91.051.BVM
1.3 1.40 1 18-201.3 1.10 2 20-22-240.9 1.10 1 20-22-240.9 0.80 2 22-24-260.7 0.80 1 22-24-260.7 0.45 2 28-30-32
310/314 0.5 0.45 1 28-30-32316
306/307308
DCE.91.132.BVC DCE.91.132.BVM
DCE.91.132.CVC DCE.91.132.CVM
DCE.91.092.BVC DCE.91.092.BVM
DCE.91.092.AVC DCE.91.092.AVM
DCE.91.072.BVC DCE.91.072.BVM
1.3 1.40 1 18-201.3 1.10 2 20-22-241.3 0.80 2 22-24-260.9 1.10 1 20-22-24
308/310 0.9 0.80 2 22-24-260.9 0.45 2 28-30-32
0.7 0.80 1 22-24-26
0.7 0.45 2 28-30-32
Note: 1) only these types are available in S series.
ø A
ø A
ø C
ø C
Fig. 1
ø A ø C
ø A ø C
Fig. 2
ø A
ø C
Fig.
Note: a wide variation of strand number and diameter com-binations are quoted as being AWG, some of which do not havea large enough cross section to guarantee a crimp as pereither MIL-C-22520/1-01 or /7-01. Our technical department isat your disposal to study and propose a solution to all your appli-cations.
312/314316/318319
3021)
303
3041)
305
3021)
303
304/3053061)
307
3041)
305
DCE.91.133.BVC DCE.91.133.BVM
DCE.91.093.BVC DCE.91.093.BVM
DCE.91.073.BVC DCE.91.073.BVM
1.3 1.40 1 18-201.3 1.10 2 20-22-240.9 1.10 1 20-22-240.9 0.80 2 22-24-26
0.7 0.80 1 22-24-26
0.7 0.45 2 28-30-32
DCE.91.134.BVC DCE.91.134.BVM
DCE.91.094.BVC DCE.91.094.BVM
DCE.91.074.BVC DCE.91.074.BVM
1.3 1.40 1 18-20312
1.3 1.10 2 20-22-240.9 1.10 1 20-22-240.9 0.80 2 22-24-260.7 0.80 1 22-24-26
340/3480.7 0.45 2 28-30-32
DCE.91.135.BVC DCE.91.135.BVM
DCE.91.095.BVC DCE.91.095.BVM
1.3 1.40 1 18-20
0.9 1.10 1 20-22-240.9 0.80 2 22-24-26
These positioners are suitable for use with both manual andpneumatic crimping tools according to the MIL-C-22520/7-01standard.
Positioners for crimp contacts 0.5-0.7-0.9 and 1.3 mm diameter
male female
Connector + Contact
ConductorType AWG
Positioners part number
For male For femalecontact contactø
A
ø C
Fig.
308/309310
312/314316/318
316/320324/330
330/340348
350/354364
320/322324/326330
® ®
Note: these turrets can be used with manual crimping toolaccording to MIL-C-22520/1-01 standard.
Turret for crimp contacts 1.6-2.0-3.0 and 4.0 mm diameter
DCE.91.202.BVCM
DCE.91.162.BVCM
2.0 2.4 1 12-14-16302
2.0 1.9 2 14-16-181.6 1.9 1 14-16-18
3031.6 1.4 2 18-20-22
Positioners
Part number
DCE.91.405.BVCMDCE.91.305.BVCM
DCE.91.205.BVCM
DCE.91.165.BVCM
304 4.0 4.0 1 10-12310 3.0 2.9 1 10-12-14
2.0 2.4 1 12-14-16314/316
2.0 1.9 2 14-16-181.6 1.9 1 14-16-18
3201.6 1.4 2 18-20-22
DCE.91.303.BVCM
DCE.91.203.BVCM
DCE.91.163.BVCM
302 3.0 2.9 1 10-12-142.0 2.4 1 12-14-162.0 1.9 2 14-16-181.6 1.9 1 14-16-181.6 1.4 2 18-20-22
DCE.91.304.BVCM
DCE.91.204.BVCM
DCE.91.164.BVCM
304 3.0 2.9 1 10-12-142.0 2.4 1 12-14-16
306/3072.0 1.9 2 14-16-181.6 1.9 1 14-16-18
3101.6 1.4 2 18-20-22
Connector + Contact
ConductorType AWGø A
ø C
Fig.
303/304309
305/306307
