Making a clavichord after NM 264.mp3.pdf

11/03/2015 Making a clavichord after NM 264.785 in the Musikmuseum

http://www.tabulatura.com/clavcho.htm#Introduction 1/63

Report onMaking a Clavichord afterN264785 in Musikmuseet

at the Instrument-building Courseat Marholmen, July 26 - August 12, 1999

by

Kenneth Sparr

Translated into English by Stuart Frankel

1999-08-20

2009-04-02

Contents This article in Swedish

Stuart Frankel's Small-But-Intense Home Page Musikmuseet (Swedish and English)

Instrument-building course at Marholmen

(English)

Johan Gabriel Högwall - fortepianomakare i Göteborg

(Swedish)

Finnish Clavichord Society Kenneth Sparr´s Page

Contents

Introduction

Case

Internal structural members

Balance rail

Rack

Keyboard

Belly rail

Nameboard

Toolbox lid

Flap

Bridge

Soundboard

Keyboard

Stringing

Listing

Lid

Lid rails

Delivery to Musikmuseet

Some personal reflections

Literature on the instrument-building courses at Marholmen.

http://stockholm.music.museum/dev-index.php?l=en

http://www.dustyfeet.com/

http://www.tabulatura.com/KLAVKORD.HTM

http://www.tabulatura.com/MARENG.htm

http://www.tabulatura.com/hogwall.htm

http://www.siba.fi/klavikordiseura/

http://www.tabulatura.com/INDEX.htm



Introduction

This report describes day by day the entire process of building a copy of an anonymous clavichord in the collection

of the Nordiska Museet (number N264785), Stockholm, now deposited in the Musikmuseet. A drawing (see picture

below!) and a soundclip of this instrument is available from Musikmuseet. The assignment, as given by

Musikmuseet, was to build a copy of this instrument and also to document the work in pictures and text. The

finished clavichord now has the inventory number X5414 in Musikmuseet, Stockholm. The report follows in outline

the building description which was made by HansErik Svensson, but diverges in some details, for example in the

order in which the work was carried out. I'm greatly indebted to Stuart Frankel who has made the translation from

Swedish to English.

http://www.musikmuseet.se/samlingar/detalj.php?l=sv&iid=177&str=

http://www.musikmuseet.se/samlingar/detalj.php?l=sv&iid=175&v=2007-12-18%2020:28:44&str=



Day 1: July 26

The points of departure for building the clavichord were well-prepared materials and a detailed written description

of the construction. Right away it could be established that the quality of the prepared material was very high.

Picture 1.

Case (pine)

Dovetailing the four case corners

The first task was to make a corner. The upper tenons were not sawed off entirely, but at a 45-degree angle. A

pencil line was drawn with the aid of a set-square 12 mm from the end on the inside of the spine. The spine was



fastened tightly to the table on its face and the side piece was held so that its inside followed the pencil line and theupper edges were level, as determined by the set-square. It was important that their upper edges come to the same

level, so if the sides were not exactly the same height, the difference in level was planed down when the sides were

glued on. With a sharp lead point the tenons were traced out. I sawed slowly and very carefully on a medium-large

bandsaw along the pencil lines on the side where the tenon will go in, without obliterating any of the line. The saw

cut went just up to where the pencil lines met. Many closely spaced cuts were sawn between the two lines. These

cuts were somewhat oblique, to obliterate the wood chips. All the rest of the wood was sawn away within the pencil

lines. If the saw cut did not end correctly at the pencil line at some point, the saw blade was backed out along the

line and the saw teeth gnawed it away. The tendons on the tops of the side pieces were cut at 45-degrees with a

small saw. Corresponding pieces were sawn out of the spine. The corner was carefully knocked together, and wood

was removed with a knife or chisel where it was in the way. The dovetail should be tight but not need force to go

together. Pictures 2-4.





Dovetailing the cheekpieces

First a notch was made in the front for the keyboard. A pencil line was drawn with a set-square on the inside of the

front, 11.5 mm from the notch. The other side was scribed down to the notch. Lines were drawn on the cheeks under

the dovetail tenons along their undersides and were sawn out, so that the sides would not prevent the cheekpieces

from reaching the corner.

The notch for the dovetail tenons was sawn out from the front.

The corners were fit. Picture 6.

Groove and notch in the cheekpieces

Both cheekpieces have a routed groove for the nameboard. The rounded end was cut straight with a narrow chisel.

A notch was sawn in the cheeks' upper edge to accommodate the nameboard. The downward saw cut followed along

the edge of the mark. The depth was a scant centimeter.

Both keyboard cheeks have a notch at the bottom for the balance rail. Lines were drawn 96 mm from the inside ofthe front and the height of the balance rail from the bottom. The corners were sawn out. Pictures 7-8.



Screwing the case walls down

The assembled (not glued) case walls were held tightly to the bottom so that the bottom extended out the samelength in front and on the sides. A check was made that the long sides were straight and the corners at right angles.

The inside and outside of the case walls were traced along the bottom. Because a long side curved, only the cornerswere traced. When the case walls were removed from the bottom the correct cuts could be made with a

straightedge.

The case walls were removed and screw holes were drilled with a hand drill between the scribed lines along the

bottom (2.0 mm). The screws were set about 5 cm from the corners and another screw put on the long sides. Thecase walls were held fast in the same position as before and holes drilled through the bottom holes into the case

walls with a 2.0 mm drill. The drill was drilled in 40 mm and a collar insured that the chuck didn't bottom out. Thecase walls were removed and the holes in the bottom drilled out to 3.5 mm. The walls and bottom were test-screwed

together. The rear wall was also checked. Picture 9.



The weather was fluctuating during the days but we took a brief dip in rather tepid water. Interesting conversationsin connections with meal times on the new organization of the Statens Musiksamlingar (State Music Collections),

music museums, music instruments, etc. In the evening we enjoyed a little concert by Mikko Korhonen whoimprovised on Bengt-Olof Sahlins Specken clavichord from 1979, the first clavichord built on Marholmen, together

with Mikko Korhonen's own reconstruction of a medieval clavichord in Pythagorean tuning, based on a descriptionand diagram of Henri Arnaut de Zwolle.

Day 2: July 27

Gluing the case walls

First the spinel was screwed to the bottom without glue. Glue was spread in the case-wall dovetails, the corners

pressed together or hit with a wooden mallet and adjusted if necessary, and the walls were screwed fast to thebottom without glue.

Clamps were attached. Wooden blocks are used behind the dovetails as guards to insure that the case walls'

dovetails were not prevented from pressing into the notch on the spine. Picture 10.



A line was drawn on the bottom along the spine to show where the bottom board should be cut.

The dovetails were planed and sanded on their undersides where the case walls were removed from the bottom. Asander was used for this.

The differences in levels underneath the case corners were planed away.

The back edge of the bottom was sawn and planed.

Gluing the case walls to the bottom

Four of the screws near the corners were set in so that they stuck up out of the bottom.

Glue was spread on the underedges of the case walls, the walls were placed on the screws and I made sure the

screws went into the holes and then screwed them until a little opening remained. The bottom was turned upsidedown and all the screws were screwed in. I pressed carefully so that I knew that the screws went into the holes. All

the screws were turned hard, I turned the case right-side up and set clamps around. Picture 12.



After the glue dried, I checked that no screwhead protruded from the bottom. If one did, it was unscrewed,countersunk, and then screwed back in.

Internal structural members

Wrestplank (oak)

The wrestplank was cut so that there were a few mm between it and the front and spine. Then glue remnants and

other gunk in the corners were removed and the wrestplank put back so that it fit as well as possible. Picture 13.

With a chisel a notch was cut for the top of the wrestplank about a cm wide and a couple of mm deep, to give the

bass end of the bridge a little more space to resonate on the bottom. I checked that the notch did not come too closeto where the wrestpins would go. A pencil line was scribed on the case wall and bottom around the wrestplank. A lot

of glue was spread inside the pencil lines and a little on the wrestplank, the wrestplank was placed there and asmany clamps between the case walls and bottom as would fit were set. Picture 14.

The glue which was forced out onto the case was removed without smearing the top of the case where it would be



noticeable later.

Balance rail

A notch was made in the left end for the left hitchpin-rail support which is as deep at the support's top surface,

coming 61 mm over the bottom. There must be no play in the notch. Three 2-mm holes were bored from abovethrough the centerline of the balance rail and through the bottom. The holes in the bottom were then drilled out with

a 3.5 mm drill.

Rear framing

The point where the backrail meets the bellyrail is 674 mm from the inside of the left case wall. A line was drawn ata right angle up from the bottom on the inside of the spine. This defines where the backrail and hitchpin rail will be

removed, and also the exact position for the soundboard and template where the holes for bridge placement will befixed.

The backrail (lime) was cut. It is 674 mm long by 22 mm at the wide end and 14.5 mm at the narrow end. Picture 16.

The notch in the hitchpin block was sawn. The hitchpin rail and the backrail will be level with the left of the hitchpinblock and there must be no error here. Because the backrail is tapered, the crosscut is not at a right angle.

Changing weather, but mostly sunny. A dip before coffee. A little playing on guitar and baroque lute waiting for theglue on the wrestplank to dry.

Evening concert in the villa with Mikko Korhonen who played exclusively on the schools' five-octave clavichord.

Day 3: July 28

The backrail was clamped tight against the level bottom with the basswood up, so that it fit closely everywhere, andthe hitchpin rail was placed as best as possible. I made sure, however, that the hitchpin rail was long enough toreach the hitchpin block. The hitchpin rail was planed narrower where it extended too much beyond the backrail atone place. The hitchpin block was shortened so that its front was level with the front edge of the balance rail. The

keybed will be as long as the backrail. This will be 40 mm at the wide end and 30 mm at the narrow. This was sawnto the right length. The hitchpin block, balance rail, and hitchpin rail were fastened tightly into position, thetemplate for the hitchpins laid on top, and indications of where to drill were punched with a special marker. Picture17.



The parts were unfastened and holes drilled for the hitchpin in the hitchpin block and rail, at a 10-degree angle fromvertical. The table on the drillpress was angled. The pins will lean back in a precise direction. Masking tape on the

drill table indicated the furthest line to be drilled on the hitchpin block and hitchpin rail which gave the right pinangles. The holes were drilled in the hitchpin block with a 1.5 mm drill, 30 mm deep. First they were drilled halfway,the drill removed and the chips poked out of the hole with a nail, and the drilling then continued. I changed to a 1.6mm drill and drilled 30 mm deep. Actually, the holes should have been 7 mm deep. The hitchpin rail was drilled first

with a 1.5 mm then with a 1.6 mm drill. The first drillings were rather unnecessary, but I read the instructionscarelessly. The hitchpin block and rail were not finished. The hitchpins were driven into the block with a wood-handled brass mandrel to a height of about 3 mm. Picture 18.

Rack

The slots on the rack were marked with a lead pencil according to the rack template for the desired fretting system.The template's treble end must line up with that of the backrail.

A set-square was used and lines were drawn between the pencil dots where the rack slots should be sawn, and alsoon the top at a right angle to the back edge.



A pencil line was drawn on the top of the backrail about 6 mm from the front edge.

A hole was drilled through the backrail from the top where each rack slot crossed this line. A 4-mm gimlet was usedin the drill press. I started carefully so that the drill wouldn't drive off course. The drive belts drove at too highspeed.

Each slot was sawn with a medium-size bandsaw with three sawcuts, one perpendicular and two angled. I wascareful not to let the saw blade touch the front of the rack. This lessens the friction between the rack tongue and

the rack, and the tongues work even if their aim isn't perfect. Picture 19.

The rack was turned up and down so that all the cuts would be sawn on the same bandsaw.

I checked that the slot was made just the right width in front with a rack-tongue slip. The hole was cleaned with around and flat nailfile. The slot was pressed out with a 1.3-mm needle.

The rack was glued against the spine. Pictures 21-24.





Balance rail fitted in. Picture 15.

Evening concert with Mikko Korhonen who devoted himself entirely to his own instrument, an anonymousclavichord built at Marholmen.

Day 4: July 29

Keyboard (pine)

Fitting

The red keyboard template was test-fitted in the instrument. There should be 1-2 mm. play between the templateand the rack. Picture 25.



The template was laid on the keyblank along the machine-planed back edge and traced out.

The keyblank's short sides were sawn so that they could be laid down between the cheeks. Picture 26.

The keyblank was fastened in the right position. Marks were set on the keyblank and along both cheeks 122 mmand 137 mm from the outside of the front for the position of the holes on the balance rail in the bass and treble.Marks were also set 48 mm in from the outside of the front on the cheeks and on the keyblank. The marks showedthe border between the naturals and the accidentals. The keyblank was taken out and lines were scribed on the

balance rail and the blank for the naturals. A pencil line was also drawn 34 mm in front of the line on the naturals'keyblank and the front edged was planed by machine to this line.

The template for the key-cover slips was laid along the keyblank's front edge with the same amount of space onboth sides between the cheeks and the rear pencilmarks scribed for the two lowest and the two highest keys. A set-square was laid on the front edge and lines were drawn from these outer keys to the rearmost lines on the balance

rail. Pictures 27-28.





An awl mark was made in the front balance-rail line between the 2nd-lowest (F) and the 2nd-highest (b2) keys. Idrilled a 2.00 mm hole through the marks at right angles through the keybed.

Rack tongues

The keyblank was laid in the instrument with the balance rail screwed down tight; it was oriented in precisely theright place and nails were pushed down through the holes to fix the keyblank's position on the balance rail. A knife

was stuck in each rack slot and with the cutting-edge a mark was pressed into the back edge of the keyblank. Aright angle was measured from the front edge out 83 and 90 mm from the back of the lowest keys at the rack-tongue holes, and 39 and 46 mm from the back of the highest key. The keyblank was taken out and two linesscribed over the blank between the markings. The front showed where the keys are angled, the rear where the cut

begins. A line was scribed between the knife mark and the nearest scribed line along a set-square set along thefront edge of the keyblank. One-by-one the tangents, which hit the strings, will be placed in these scribed lines. Aline was drawn with the set-square on the back edge at each knife mark to show where the hole for the racktongues will be punched. Holes were punched for the tongues, with the keyblank's front edge held against the

steady, horizontal base. The holes will be at right angles to the front edge, so the tool was therefore held plumbstraight. The edges of the corners were fastened on each end by rack-tongue slips, and the right length was cut offand the rack tongues were pounded tightly in with the front end down in the hole. They were pounded in with aspecial wooden block. The tongues were filed on both sides, top and bottom, so they had their full width only in the

middle. While the keyblank was still whole, it was roughly sanded. An evening concert with Mikko Korhonen on mySpecken clavichord. Weather sunny and warm. A dip before lunch, coffee, and dinner.

Day 5: July 30

Marking out the keys



A pencil mark was made by eyeing back on the keyblank in the middle of the scribed lines. In order to work, for thekeys to be spaced correctly with E and B unfretted in the middle of the keyboard, one part of the scribed lines mustwind up outside the center of the keys. A plastic-film keyboard template, previously used for scribing out the keys,

was pressed into service again.

Pencil lines were drawn along the set-square as before, up to the second scribed line. The lines show the backedges of the keys. The template for scribing the keyboard was fastened down, the keys marked and scribed withthe set-square against the front edge. Lines were drawn to the back line scribed on the balance rail. The slantedlines outlining the keys were drawn in the middle of the keyblank. Picture 32.

Balance holes and pins

I marked with a pencil all the keys, the accidentals (back scribed line) and naturals (front scribed line), in order tobe able to keep them in order easily. For the balance holes, an awl mark was made along the two scribed lines andin the middle of each key.

Outside the instrument, with the keyblank tightly pinned to the balance rail, holes were drilled (2.0-mm drill)

through the keyblank down into the balance rail (total 33 mm deep). A hand drill was used and a special water levelwas attached for plumb-straight drilling. The balance holes were also drilled in the balance rail.

The bevels were planed up to the pinholes in the balance rail. The cheeks were glued. Picture 29.



Balance rail glued and screwed in. Picture 30.

Balance pins were driven in. A measuring block was used to get the right height (17 mm). Picture 31.



Threads were put on the balance pins to act as bushings. They were fastened with wooden nails and pins in the bassand treble. Separate threads were used for the front and back balance pins. The threads go on every other side, orone pair of pins in each octave, so that they don't interfere with the pins.

The holes in the keys were chiseled out with the help of a special tool and a little chisel. Evening concert with

Mikko Korhonen who played on Anna Axbergs recently completed Wåhlström clavichord and on my Speckenclavichord.

Day 6: July 31

The balance holes were punched. For better precision, the oblong holes were first cut at the top with a little chisel,

but smaller, at least in surface area, than the final hole would be. After that the holes were punched. The holes werewidened from above with a special tool with a 2.6-mm point and a metal handle. The keys were numbered from bassto treble (1-47). The numbers were written between the scribed lines on the balance rail.

Gluing the pinblock

Masking tape was put on the case walls. The pinblock was glued and pressed against the side wall, against thespine, and down against the balance rail and rack (with a support block underneath). The glue was spread first on

the pin block, then on the case walls and in the notches. Picture 33.



Key covers (pear, original boxwood)

A ruler was fastened tightly on the keyblank along the back edge of the natural keys. The covers were laid out asdesired. The planed edge should be turned against the ruler. All the splices were laid between the keys.

The covers were glued. I made sure they didn't slide when they were clamped down. Pictures 34- 35.



The front edge was shifted when the glue had dried. A completely smooth edge is necessary to cut the keys right.

Scribing the decorative lines on the naturals

The seam separating the natural and accidental keyblanks corresponds with a scribed line.

In front of this line three further lines are scribed, the space between them being 1.5, 3, and 1.5 mm.

A hobby knife and ruler were used. I drew as many times as needed to give the full depth the whole way. Pictures36-37.



Tracing out the keyboard

Pencil lines were scribed in the seams on the keyblank for the naturals..

These pencil lines were examined through the keyboard template, and I judged that all the front key-cover slips

looked like they had same width.

Sawing them out

The keyblank was sawn out.

All the straight saw cuts were sawn from the front and the back on a small bandsaw. I was very careful about the

covers when I made the sawcuts from the front.

The accidentals were sawn free from the naturals with a fret saw.

Because the keyblank was large, all the cuts couldn't be made at one time. The blank was sawn apart between e

and f, and between b and c, in all the octaves. All the straight cuts were sawn from the front and from the back. The

front edges of the accidentals were all fret-sawn a bit in back of the naturals. The keys were sawn apart. Pictures38-40.





Evening concert with Mikko Korhonen on his own Wåhlström and anonymous clavichords.

Day 7: August 1

Putting the naturals in

All the naturals were sawn on a slant, since the key cover is wider than the base of the key, without any of theblank itself being sawn away. A 60-degree angle was chosen. A Japanese saw and a little backsaw was used. The

sides of the keys were roughly planed. Picture 41.

Putting the accidentals in

All the accidentals were cut away in front at a 75-80 degree angle so that the pencil marks just disappeared.

Bellyrail



The back of the bellyrail was correctly sized so that the longer side was 65 mm.

Glue was spread on the underside and ends, and a piece of wood was laid on top to come up to the level of the case

walls and clamped tightly downward, towards the back, and against the rack. I made sure the belly rail was at aright angle to the back wall. Picture 42.

The longer part of the bellyrail was sawn off so that it fit correctly between the higher side of the keyboard and the

shorter part of the bellyrail. A notch was sawn for the balance rail.

The mousehole was scribed according to the template. The circle were drilled with a special 11-mm drill. I used thedrill press and drilled first from the outside of the belly rail so that the drill point just went through. The bit was

changed and drilled from the other hole.

A row of smaller holes was quickly drilled in the upper and lower edges. I chiseled out with a chisel and cut cleanwith a knife.

The belly-rail sections were glued. Picture 44.



Nameboard

The nameboard was sawn to the right length and whatever had to be removed was scribed. I cut away with a chisel

and gradually tested its fit in the instrument.

So as not to make a ledge where the moldings meet, a moulding was sculptured which connected to the moulding ofthe cheeks and gave the impression of a mitered corner. Picture 43.

The evening was devoted to a trip to Furusund and an estimable concert with the ensemble Mare Balticum from

Musik i Skåne (Music in Scania). The concert took place out of doors in a wonderful summer evening before largeand enthusiastic audience.

Day 8: August 2

Soundboard liners

Battens were cut to fit between the bellyrail and wrestplank, the wrestplank and right cheek, and along thekeyboard side back to the bellyrail. Picture 45.



The battens were glued in and I made sure that they stayed in the right position, level with the bellyrail and

wrestplank, when the clamps were tightened.

The level of the joints was adjusted all around after the gluing. Where the support was too high, it was lowered witha sanding block.

Toolbox lid

I made the toolbox lid the right size so that it was even with the back edge of the toolbox and also with the back

edge of the nameboard.

The width was adjusted to fit the compartment.

The lid was veneered with highly figured walnut, smoothed and finished with raw linseed oil and beeswax on the top.Picture 46.

I drilled with a 1.6 mm drill very straight through the case walls, placed the toolbox lid in the right positions,

knocked the axle in a bit, and checked that lid opened and shut correctly.



The axle was taken out and a hole was drilled in the lid with a 1.5 mm drill.

The axle was put in all the way before the instrument was painted.

Block

A block was cut so that it could driven in between the hitchpin block and the left cheek. Also, a small piece of wood

was fit in so that the toolbox lid would go in its original position.

The block and small piece of wood were glued. A piece of wood which reaches over the case walls was set on top tofacilitate clamping. Glue was spread on the hitchpin rail, balance rail, and cheek, not on the block. Picture 47.

Flap

I checked that the flap fitted well in the opening in the case. Picture 48.

Soundboard (spruce)



A pencil line was drawn in the middle of the soundboard at right angle to the grain.

A cross mark was set in each end so that it would remain even when the soundboard was sawn out to an exact

measurement. The space between the markings was measured exactly and the measurement written down.

The soundboard was put into a drying cabinet and taken out after a couple of hours. The distance between the

markings was measured again and the new value written down. The drying was continued until the board stoppedshrinking.

The fit of the soundboard template was checked in the instrument. Picture 49.

The soundboard outline was scribed according to the template with possible corrections.

The soundboard was sawn out.

The soundboard was fitted so that it fit precisely.

The template was laid on the soundboard.

I marked holes for positioning the bridge with an awl through the template.

Holes were drilled (3.0 mm) in the soundboard bridge markings..

The position for the rib (or ribs) was marked on the underside.

Bridge (sycamore)

The bridge was screwed tightly to the soundboard from underneath. Picture 57.



The soundboard was laid in the instrument. The template-strip for the bridgepins was attached to a plastic angleand the measurements checked. Picture 51.

The positions for the bridge pins were marked from the template-strip with a pencil.

The soundboard was taken out, the bridge unscrewed, and a mark made in each pencil cross with special markers.

I didn't use the drill press since it was hard to get the drill centerd and on an even level. I used the hand drill



instead.

The drill (0.9 mm) was set in and I checked that it was correctly centerd. Its depth was set to 7 mm.

I drilled so that the angle the whole time was in the direction of the bridge at the drilled hole. Picture 54.

The upper side of the bridge was colored with a pencil and a line was drawn on its left side (outer curve) a scantmillimeter under the upper edge.

The upper side of the bridge was fastened at an angle down on the pencil line with a angled Sandplate (sanding

block). The pencil mark should disappear around the bridgepin holes but remain along the ridge. Picture 56.

The side of the bridge was rounded if possible a bit against the bevel so that the bevel surface would not be so wide.

The bridge ends were cut with a Japanese saw. I fine-cut with a sharp knife.

The bridge was finished with shellac, but not on the underside which will be glued.



The bridge ridge was waxed with beeswax, spread on with a finger, let dry, and then rubbed with a rag. The

procedure was repeated a couple of times. The waxing was done so that the strings would slip more easily, whichwould facilitate tuning and improve the tuning stability.

Filing the tangents

The tangents were clamped fast in a screw clamp between pieces of wood (or in an aluminum clamp) so that the

jaws didn't make marks, and the long sides were filed with a simple-ridged file. I was careful not to damage thetops.

The warm night was devoted to an evening dip with Björn and Olle and then continued work until midnight.

Day 9: August 3

I used a special tool to ream out the holes in the keys for the balance pins. Picture 52.

I checked that the keys moved easily with the help of a piece of wood which was furnished with a balance pin. This

was clamped tightly to the bench and I tried the key's path. I took out the future neighboring keys so that theycould not disturb things and I put each key in its place in the instrument.

The rack tongues were cut or filed so that the key moved without binding but with as little sideways play as

possible. The tongue will be smaller towards the top and bottom and have its full width only in the middle. Thiswould not work unless the tongue sits exactly vertically.

The key should now move freely and easily.

Day 10: August 4

The nearest straight keys were laid in and I cut and planed them free from each other.

When all the natural keys were laid in, their sides were planed so that all the gaps between their fronts were just

right and the same size.

The backrail was set in place by being pressed up to the rack, sitting on blocks. Picture 53.



The accidentals were smoothed. The edges were carefully rounded on top and in front. Picture 55.

The soundboard was smoothed.

The bridge was glued. I used a piece of chipboard with a notch for the bridge curves.

First I did a dry run. The bridge was screwed in and I used as many clamps as would fit.



The right amount of glue was spread on the underside of the bridge, it was placed on the screws which stuck up and

I let the screws help position the bridge, then the whole bridge was pressed down, all the screws screwed in and

clamps put on. Picture 58.

The bridge was masked with masking tape. The soundboard was finished.

Very thin shellac was used, flowing from brush strokes with the grain, but not so much that it ran. I polished it withsteelwool after it dried.

Day 11: August 5

The bridge pins are made of 1 mm brass wire. I put the wire into each hole into a special bridge-pin workblock and

cut it off straight across with clippers. I filed over the whole workblock so that the pins made a level surface. Theworkblock was turned over and the pins knocked out. 62 pins were needed. A special tool was used to tap the pins

into the pre-drilled holes in the bridge. First the pins were pushed down some mm and I felt to make sure they were

tight in the hole at the right angle, then I hammered carefully with small taps and listened to the sound when the pinreached the bottom. The pins were bent with a special tool so that they sloped at right angles to the direction of the

strings. The pins were filed to an even height with a file.

The rib was glued and shaped. The notched chipboard for the bridge was used. I also made sure that the rib endsdidn't protrude beyond the soundboard. Pictures 59, 61, and 62.





Old clavichords often have thin strips of parchment glued under the ends of the bridge across the grain. Paper

strips were glued in the same way.

The soundboard was glued in. Picture 63.

Lid rails

The rails for the sides of the lid were cut to the right length

I tried to tap them into place. I sanded the lid notch where it fit too tightly.

The ends were shaped.

The rails were glued down. I glued only the front edge and a little on the back edge so that the lid could twist

without cracking. Picture 60.



Flap

The flap was furnished with a threaded hinge.

Holes were marked with a awl in the outer corner of the bottom edge and drilled with a 2 mm drill at a 45-degree

angle. The flap was held in place and corresponding holes were marked in the case. I marked with an awl anddrilled at 45 degrees through the case. Two threads folded in the middle were set together and I pressed to make

the twisted knots small and tight. The straight parts were cut correctly, a little unevenly, if the thread wouldn't go

through the flap. For now, the hinges will be allowed to stick out on the inside of the case, so the lid can be removedfor painting. Pictures 64-65.



Wrestpin holes

The wrestpin template was laid against the back and side walls and fastened with a pin in the treble and bass.

Picture 66.



All the holes were marked with a special marker

A rod with a point surrounded by a ring was fastened into the hand drill.

The point was set in each mark and I let the ring cut the fibers so that the soundboard wood did not shred when

drilled.

Holes were drilled with a 2.6 mm drill 20 mm deep at a 5-degree angle.

Then with a 3.3 mm drill, I drilled 5 mm deep. Picture 67-68.



Arne Lindberg and I skipped Mikko Korhonen's evening concert in order to try out Mikael's newly completed lute.

We played some duets on Mikael's and my lutes from the 1984 Marholmen course.

Day 12: August 6

Keyboard

The two accidentals which are to be divided were cut.

The accidentals were put in position and cut in the back so that they had the right clearance with the naturals in the

front and against the nameboard in the back.

First all the g-sharps were glued; these were placed in the middle of the gaps between the naturals. Picture 69.



Glue was spread under the accidentals, they were set in place and pressed by hand, sometimes with a little press. I

checked that they were set correctly, and let them dry.

The template was used and the remaining accidentals were glued. Picture 73.

Balancing the keys

I sawed and cut away in front on the undersides of all the naturals. Evening concert (public) in the church at Länna

with Mikko Korhonen on organ and on my Specken clavichord. Arne Lindberg and I played two lute duets (LaRossignol and My Lord Willoughbies Welcome Home) on our new lutes. Picture 76.

Day 13: August 7

The natural tails were glued. Those for the D keys are wider than the others. I planed to the width which gave the

right clearance and pressed down.



The side edges of the naturals were beveled from the front to the first scribe line. The beveled edges were roundedwith a knife and sanding sticks.

Hitchpins

The hitchpin rail was glued. It was clamped against the spine, the rack and the hitchpin block. Blocks were driven inunder the rack to give support against the bottom. I made sure that glue didn't get in the holes, and glued thesupport blocks. Pictures 83-84.



The backrail was glued against the spine and the rack. It was pressed against the rack with blocks.

The backrail cloth was fastened on with a number of dots of glue. Picture 85.

The remaining hitchpins were driven in with a wood-handled brass mandrel. Support blocks were set under the

backrail.

Stringing

I took as many wrestpins as would be used for the first string gauge. When they had been used it would be time tochange gauges, and so I laid out as many pins as would be needed.

I wanted to have a red felt mark on the A pins so I put red pins in all the holes which would have the felt marks sothey wouldn't be left out.

The loop-making machine was fastened down with two wooden clamps, the left one opening up and down. The wire

coil was hung over the metal bar sticking up out of the left clamp, and a 10-cm end of the wired was wound aroundthe machine's hook. The end was twisted counterclockwise turning around the wire and I stopped about 3 cm fromthe hook by bending the end at a right angle out from the wire. The end and wire were held fast with pliers and themachine pedaled again. I let it whirl until there were enough windings.

The wire was stretched straight out from the hook and the end bent back and forth along the wire until either it

broke off or I snipped it off 4-5 mm from the windings with wire cutters.

Acceptable loops were hooked on their hitchpins and the string placed on the correct bridgepin. The schedule forstring length beyond the wrestpins determined where the wire would be cut with wire cutters.

The wrestpin was held horizontally with the flat end to the right and with the string along the wrestpin with its end



even with the bottom of the wrestpin.

The wrestpin was rolled in the same direction as one pedals a bicycle and I let the string turns go over the stringends and held them to the pin. The string must at all times be held in tension until the pin is hammered into its hole.

At the beginning, one hand must hold both the end of the string and the rolled-up coils when the other hand had totake a new grip. After several turns, the string was fastened to the pin and then it wound a little more freely, but thestring had to be held under tension the whole time, otherwise the winding would immediately come loose.

When there were about 5 centimeters left to the hole, the end of the string was taken off so that the last few

windings went around only the pin and not also over the end of the string, which would make the string easier toremove in the future.

Taking a firm grip on the windings with my right hand, I bent the end of the string back and forth until it broke. Thestring was held under tension the whole time.

When there were a couple of centimeters left until the hole, the last windings were spaced out, the pin was turned

right and put down into the hole. The string was tightened as necessary with the tuning wrench and the pinhammered in so that it held fast. If necessary, the height of the level where the string leaves the pin could beadjusted; after that the pin was tapped down to the right level. I checked that the string was tense enough before I

went on to the next step. Pictures 86-87.



Evening concert with Mikko Korhonen who played Ragnar Köhlin's Specken clavichord.

Day 14: August 8

After sanding and fine adjustments, the key coverings on the naturals and accidentals (but not the ebony coverings)were coated with clear so-called Danish Oil. I kept putting on oil for it to absorb until my patience gave out. The

excess was wiped off and I let the oil dry. Pictures 88-89.



The tangents were sorted by size, the widest in the bass.

I started installing the tangents from the bass. A marking tool was set so that the pin extended between the strings

in the relevant stringpair and could press a mark in the scribed line on the key. Unfretted keys got the tangent inthe middle of their scribed line. The scribing was done according to the rack template where the strike point hadbeen calculated according to string lengths on the scribe lines used for measuring. I therefore made sure that the

strike point came entirely from the true string length. A supplement to the instructions described how thecalculation was made with the help of a calculator. I set the striking points by compass with the aid of verniercalipers. The compass was laid flat on the keys. I wrote the values in a table, which was also found in thesupplement. One tangent was done at a time, at least to start with, so that the method and the result could be

validated.

The hole was marked and punched. I tapped the punch down a bit at a time and loosened it in between, so that itdidn't get fastened too tightly. It was rocked loose lengthwise, never crosswise.

The holes were punched next through the keys.



The edge of the tangent against the sounding part of the string must be clean and sharp. I felt against a nail whichedge which sharpest. The tangent was tapped in with a wood block to a height of 20 mm. The tangent was polished

in a special tool to make an even and smooth contact surface.

Listing

The listing was woven through the strings and I made sure that the tangets hit correctly.

The listing was woven alternately under and over the string pairs with a few fairly hard, tight loops. One or two

string pairs per loop gave a steadier and less wobbly touch, but also a little stiffer and with a weaker tone. So thatthe two strings in the pair wouldn't lie too closely to each other, another cloth was inserted between the strings inthe pair and between the woven listing and the tangents. The distance was tested. Pictures 90-91.



Mikko Korhonen played a concert in the evening on his quite recent clavichord, a 5-octave instrument builtaccording to principles from the smaller Specken clavichord. Fantastic instrument and fantastic music!

Day 15: August 9

I continued with the tangents and weaving the listing. Together with HansErik Svensson, I made many adjustmentsand corrections. After all the tangets were tapped in, we started to tune the instruments. Pictures 92, 95, and 98.



Soundboard moldings

The moulding is the same as that of the case walls and runs the same length.

The moulding ends even with the right cheek.

At the rack it is angled straight, and ends even with the rack's edge.



The corners were made tight and pretty.

The moldings and insides of the case were finished with raw linseed oil.

Lid

The lid was held so that it extended out the right amount over the front case wall (about 5 mm). A line was drawn on

the lid's underside along the spine. The edges were planed by machine.

Lid hinges

The lid on the original had three hinges, one 146 mm from the left outer corner, one 493 mm from the left outercorner, and one 131 mm from the right outer corner. Such hinges were made and installed on the lid and back of thecase.

Lid cord

The lid cord was fastened with a staple in the pin block and a staple in the lid. The original position on the pinblockappeared on the drawing; the lid fastening was missing because that part of the lid is gone. The original thus now

has the lid cord on the right side.

To make the staples look old, they were made of bent and hammered iron wire.

I started first with a 2 mm drill.

The lid cord was knotted tight. The lid must not tilt back too far.

Evening inaugural concert on the ready clavichord. Because of the extremely high humidity (70-80%) there were

problems with tuning stability and some of the tangents' functioning. Picture 100.

Day 16: August 19.

Carving the key levers

From the scribed lines back until just before where the key bends a concave knife cut is carved from the outer edgeand down against the ridge but so that there was a ledge between the "ski point"-like cut on the bottom and theridge.



To make a ledge on top, the ridge on the key must lie a little under the level of the top surface. Therefore the ridgesurface of one side was first cut somewhat beyond the midline of the key. When the opposite ridge surface was then

cut so its back wound up in the middle of the key, it was also somewhat lower in level.

In front, the ridge was finished by knife in a gentle curve going up to the surface at the back line of balance-pinholes.

Previously I had cut and planed the right clearance between all the keys in back of the nameboard.

A scribed or pencil line was drawn near the middle of the keys where the ledge will be.

Lines were drawn along the sides of the keys with a special scribing tool (a wood block with a screw)

Two sawcuts with a little backsaw in the scribed line determined the length of the ridge in the back. Each cut wassawn almost until the middle of the key and to the scribed lines on the side.

With a chisel (or knife) the sides of the ridge were cut to the width of the markings. First the ends against thesawcuts were cut. Then I cut along the entire ridge with the grain, not against. Because the ridge would be cut down

to "ski points"at the back, the ridge cuts were started a bit in front of the sawcuts.

Then the second ridge side was cut in the same manner. I cut far enough in so that the back of the ridge came to themiddle of the key. Since the second side was cut a little beyond the middle, the ridge wound up lying a little lowerthan the surrounding. Picture 102.

"Ski points" were cut with a small knife between the scribed lines and the saw cuts. Picture 106.



After sanding, the clavichord was painted light blue with oil paints (pigments: Paris blue, titanium white, and Picture119.

Day 17 - August 11

Gluing the soundboard moldings

The corners were made close and nicely even

During the gluing a line of glue was put in the corner between the soundboard and the case and the mouldingpressed in place by hand.

After a couple of minutes I checked it and pressed a little more.

Evening concert with Mikko Korhonen who played on Bengt-Olof Sahlin's adjusted Specken clavichord and his ownnewly built one.



Day 18: August 12

Morning was devoted to cleaning out and tidying up the workplace. Pictures 121 and 123.



Following afternoon coffee, all the instruments were set up in the lecture hall for testing. Pictures 127-131.







Delivery to Musikmuseet



In October, 1999, the clavichord was delivered to Musikmuseet for incorporation in its collections. Hopefully, it willbe allowed to sound on different occasions. Here are some pictures from the museum with the clavichord.





Some personal reflections

I built my first instrument, a clavichord kit from Carl Fudge, USA, at Marholmen in 1980, thus the second year ofthe course. I came there as a complete novice with only school woodworking as background. To build thisinstrument myself, of course with considerable help and support from HansErik Svensson, was a revelation. Ilearned to handle tools, acquired knowledge of materials, and solved problems of construction in a meaningful,

stimulating environment. This became an immediate twenty-year-long passion and every course I learnedsomething new. It has also been a fantastic experience to be able to make the learning trip - of course, it can becalled a research trip - and the courses during these years have meant much. For my part, they have meant that a

number of music instruments have come into existence during the course of these years: in 1984, a 10-courserenaissance lute; in 1987, a guitar copied after Grobert; in 1992, a clavichord after Specken; in 1993, a baroqueguitar after Deleplanque; in 1994, the stand for the Specken clavichord; in 1995, a 13-course baroque lute after

Martin Hoffman; in 1998 a guitar after an original in my possession; and in 1999, a clavichord after an anonymousinstrument in Musikmuseet. During the course of the years I have also devoted myself to renovation work of myown old instruments at Marholmen: three guitars and a fortepiano by Johan Gabriel Högwall.

One can perhaps wonder why I never occupied myself with instrument building during the other parts of the year

rather than only during the opportunities I had at Marholmen. This is easy to explain: Marholmen, with HansErikSvensson and Arne Lindberg as teachers, has offered unique opportunities to dedicate oneself wholeheartedly andwith all one's body and soul to instrument building in a meaningful, stimulating atmosphere, physically andpsychologically. For my personal part, taking part has implied relaxation and stimulation, and I have never found its

equivalent in another context. I would also like to state, or at least believe (others can judge for themselves), thatthe Marholmen stays have had great meaning for my personal development: an increased self-knowledge,increased ability with handiwork and materials, increased respect for artisans of the past and for their skill. I

consider it as an extraordinary favor to have been part of the courses at Marholmen.

The building of the clavichord copy for Musikmuseet in 1999 went, from my point of view, exceptionally well. I hadfirst-rate wood to work with and it was a real joy to work with and shape it. I worked more or less intensively about10 hours a day, 7 days a week, building the clavichord, which totaled in all about 170 hours. I am, however, a

reasonably experienced builder and not too finicky about details. It's otherwise easy in instrument building to loseyourself in these details. Different from lute building, there was a certain amount of repetitive part in clavichordbuilding (keys, stringing). The complexity of clavichord building lies in making the mechanism function well and fine

adjustments of the tangents, the tangents' installation, working the listing cloth in, etc., which are so very importantfor the resultant sound. I think that the evolutions of things at Marholmen has been very interesting, and thecharacteristic sounds of the instruments have been a very important aspect of the building. This evolution has,

therefore, not had to do primarily with producing instruments, but also with attaining a certain quality of sound andsuccessive improvements.

In 1999 the last of the instrument-building courses at Marholmen ended. The Birkagården Folkhögskola (Adult Edcenter) thereby broke a 20-year-old tradition which was unique in the world. The stated reasons were economic, butit was perfectly obvious that the school's management lacked both the interest and the will to drive the enterprise



farther. As an outside observer, I was enormously surprised and shocked over how the whole question had beenhandled by the management of the Folkhögskola.

Literature on the instrument-building course at Marholmen.

Printed works

Sparr, Kenneth, Konsten att bygga luta på 14 dagar [SGLS 18/1985 nr 3 s. 14-26]

Sparr, Kenneth, Gitarrbygge sommaren 1987 [Gitarr och Luta 21/1988 nr 1 s. 34-50]

Sparr, Kenneth, Instrumentbyggarkurs på Marholmen 1996 [Gitarr och Luta 29/1996 nr 3 s. 4]

Sparr, Kenneth, Instrumentbyggkurserna på Marholmen - unika i världen [Birkagårdens folkhögskola 80 år.Stockholm 1997 s. 25-40]

Articles on the Internet

Sparr, Kenneth, Instrumentbyggkurserna på Marholmen - unika i världen.

Sparr, Kenneth, Musical Instrument Building Courses at Marholmen, Sweden - Unique in the World.

© Kenneth Sparr

http://www.tabulatura.com/MARHOLM.htm

http://www.tabulatura.com/MARENG.htm

Documents

Making a clavichord after NM 264.mp3.pdf