M-Vision Cine 3D series - ProjectorCentral · Digital Projection M-Vision Cine 3D series 1. USING THE MENUS Operating Guide Rev A August 2011 Page 2 Using the Menus Use.the.buttons.on.the.projector.control

Rev A August 2011

M-Vision Cine 3D series

High Brightness Digital Video Projector 16:9 widescreen display

OPERATING GUIDE

112-022A

Digital Projection M-Vision Cine 3D series CONTENTS Operating Guide

Rev A August 2011

CONTENTS

About this Guide ........................................................................................... 1Symbols used in this guide .......................................................................... 1

Warnings..................................................................................................... 1Notes........................................................................................................... 1

Product revision ............................................................................................ 1

Using the Menus ........................................................................................... 2Navigating the menus ................................................................................... 2Submenus ...................................................................................................... 3Selecting parameters .................................................................................... 4Sliders ............................................................................................................ 5Commands ..................................................................................................... 5

A Tour of the Menus ................................................................................... 6Main Menu ...................................................................................................... 6

Aspect.Ratio................................................................................................ 6Presets........................................................................................................ 7Brightness,.Contrast,.Saturation,.Hue,.Sharpness.and.Noise.Reduction... 8Overscan..................................................................................................... 8Input.Select................................................................................................. 8Resync........................................................................................................ 83D.Settings.................................................................................................. 8

Advanced Menu ............................................................................................. 9Color.Space................................................................................................ 9Gamma,.Color.Temperature.and.Color.Gamut........................................... 9Brilliant.Color®.and.Adaptive.Contrast........................................................ 9Fine.Sync.................................................................................................... 9RGB.Adjust.................................................................................................. 9

System Menu ............................................................................................... 10Language.................................................................................................. 10Menu.Position........................................................................................... 10Blank.Screen............................................................................................. 10Auto.Power.Off.......................................................................................... 10Auto.Power.On.......................................................................................... 10Rear.Projection......................................................................................... 11Ceiling.Mode............................................................................................. 11Lamp.Power.............................................................................................. 11

Control Menu ............................................................................................... 12Keys.1.to.5................................................................................................ 12Trigger.1.and.2.......................................................................................... 12Auto-Source.............................................................................................. 12

Service Menu ............................................................................................... 13Information................................................................................................ 13Factory.Reset............................................................................................ 13Blue.Only................................................................................................... 14Test.Patterns............................................................................................. 14Altitude...................................................................................................... 14

Menu Map ........................................................................................................ 15MAIN ............................................................................................................. 15ADVANCED .................................................................................................. 15SYSTEM........................................................................................................ 16CONTROL ..................................................................................................... 16SERVICE ....................................................................................................... 16

Digital Projection M-Vision Cine 3D series ABOUT THIS GUIDE Operating Guide

Page 1Rev A August 2011

About this GuidePlease.read.this.guide.carefully.before.using.the.projector,.and.keep.it.handy.for.future.reference.

A.serial.number.is.located.on.the.side.of.the.projector..Record.it.here:.

Symbols used in this guideWarnings

ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely followed.

WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment unless the instructions are closely followed.

Notes

NOTE: this symbol indicates that there is some important information that you should read.

Product revisionBecause.we.at.Digital.Projection.continually.strive.to.improve.our.products,.we.may.change.specifications.and.designs,.and.add.new.features.without.prior.notice..Projectors.built.prior.to.this.revision.of.the.Operating.Guide.may.therefore.not.include.all.the.features.described.

Digital Projection M-Vision Cine 3D series 1. USING THE MENUS Operating Guide


Using the MenusUse.the.buttons.on.the.projector.control.panel.or.on.the.remote.control,.to.access.the.menu.system.

Notes

Some menu options and controls may not be available due to settings in other menus. These will be shaded green on the actual menu.

Remote controlProjector control panel

Navigating the menusTo.open.another.menu,.first.close.the.current.menu.by.pressing.MENU,.

Select.another.menu.using

.and ,

•

•

To.open.or.close.the.on-screen.display.(OSD),.press.MENU.

The.first.item.in.the.menu.is.highlighted.

(When.closing.the.OSD,.you.may.need.to.press.MENU.more.than.once.if.any.sub-menus.are.open.)

•

.Select.an.item.in.the.menu.using

.and .

•

then.press.ENTER/SELECT.

The.first.item.in.the.new.menu.is.highlighted.

•


Page �Rev A August 2011

SubmenusSelect.a.submenu.using

.and .

then.press.ENTER/SELECT.

•

•

Notes


The.submenu.opens,.with.the.first.item.highlighted.

•

To.close.the.submenu,.press.MENU.•



Selecting parametersMost.parameters.are.changed.by.selecting.from.a.list:

Select.from.the.list.using

.and. .

The.change.will.be.made.immediately.

•

•

Notes


Some.parameters.are.changed.by.selecting.from.a.submenu.

Press.ENTER/SELECT.to.open.the.submenu.

The.item.that.is.currently.selected.is.highlighted.with.a.green.dot. .

Select.from.the.list.using

.and .

The.change.will.be.made.when.you.press.ENTER/SELECT.to.confirm.the.selection.

•

•

•

•



SlidersActivate.the.slider.by.pressing

.or. .

•Notes


CommandsTo.use.a.command,.press.ENTER/SELECT.

In.the.example.below,

use. .or. to.select.YES.or.NO,

then.press.ENTER/SELECT.to.confirm.your.selection.

•

•

Use. .or. to.adjust.the.value.

Press.MENU.or.ENTER/SELECT.to.accept.the.value.

••

Digital Projection M-Vision Cine 3D series 2. A TOUR OF THE MENUS Operating Guide


A Tour of the Menus

Main Menu

Aspect Ratio

Use. .or. .to.choose.between.16:9,.Theaterscope,.4:3,.4:3 Narrow.and.Native.

Examples

•

Notes See also Using the Menus, earlier in this guide and Menu Map, later in this guide.

The Native image examples shown here have far fewer pixels than the 1920 x 1080 of the DMD. Your image may be different.

When displaying a 1�:9 image, DO NOT use an anamorphic lens.

1�:9 image using Native setting 1�:9 image using 16:9 setting

�:� image using Native setting �:� image using 4:3 setting




An anamorphic lens is used with the Theaterscope setting, to ensure that for a 2.35:1 image, the maximum area of the DMD is used, giving maximum image brightness.

The 4:3 Narrow setting is used to compensate for the distortion that an anamorphic lens would cause to a �:� image.

When displaying a 1�:9 image, DO NOT use an anamorphic lens.

Main MenuPresets

Presets A, B and C can also be recalled using the USER MEMORY keys on the remote control.

Note: Preset D is available only through the Preset menu, not through the remote control.

When Save Presets is selected, the image settings for ONLY the selected input are saved.

4:3 Narrow without anamorphic lens 4:3 Narrow with anamorphic lens

2.��:1 image using 16:9 setting without anamorphic lens

2.��:1 image using Theaterscope setting without anamorphic lens

Examples with anamorphic lens

2.��:1 image using Theaterscope setting with anamorphic lens

PresetsThe.current.image.settings.can.be.saved.to.one.of.four.Presets..Any.of.the.four.Presets.or.the.Default.settings,.can.be.recalled.later.•

The.following.settings.are.saved:

From.the.Main.menu:

Aspect Ratio Brightness Contrast Saturation Hue Sharpness Noise Reduction Overscan

From.the.Advanced.menu:

Color Space Gamma Colour Temperature Color Gamut RGB Offsets RGB Gains Brilliant Color Adaptive Contrast

•



Brightness, Contrast, Saturation, Hue, Sharpness and Noise ReductionAdjust.the.sliders.for.these.settings.

OverscanChoose.from.Off,.Crop.or.Zoom.

Input SelectChoose.which.input.source.to.display.

ResyncPress.ENTER/SELECT.to.force.the.projector.to.re-synchronise.with.the.current.input.signal.

3D SettingsPress.ENTER/SELECT.to.open.the.3D.settings.sub-menu.

Set.3D Enable.to.On.or.Off.

Set.3D Type.to.suit.the.configuration.of.the.3D.input.signal.

Set.DLP Link.to.On,.if.you.are.using.3D.glasses.that.can.utilise.the.DLP.Link®.signal.embedded.in.the.image.

If.the.3D.images.are.displayed.in.the.wrong.order,.set.L-R Swap.to.Swap.

•

•

•

•

•

••••


Overscan is used to compensate for noisy or badly defined image edges, by either:

- cropping the edges from the image

or

- increasing the size of the image, to force the edges off-screen.

Main Menu3D Settings

�D video is not possible with all inputs. See the Connection Guide for more information.

3D Type can be set only when 3D Enable is Off.

DLP Link and L-R Swap can be set only when 3D Enable is On.



Advanced Menu

Color SpaceSet.this.to.Auto,.except.when.the.projector.has.problems.selecting.between.YPbPr,.YCbCr.and.RGB.

Gamma, Color Temperature and Color GamutSet.this.to.suit.the.specification.of.the.input.source,.or.to.improve.the.appearance.of.the.projected.image.

Brilliant Color® and Adaptive ContrastSet.these.to.suit.your.brightness.and.contrast.requirements.

Fine SyncAdjust.these.settings.to.suit.the.configuration.of.the.input.signal.

RGB AdjustAdjust.the.RGB.offset.and.gain.settings.to.improve.the.colour.balance.of.the.projected.image.

•

•

•

•

•


Brilliant Color® allows for increased projector brightness and improved color saturation by enabling the yellow segments on the colour wheel.

Adaptive Contrast expands the light and dark portions of the contrast curve of the image, depending on the mean luminance of the image.

Setting either of these two parameters to On will affect any image quality settings made in other menus.

Advanced MenuFine Sync

Fine Sync and RGB Adjust affect only RGB input sources.




System Menu

LanguageThis.product.is.available.only.in.English.at.present.

Menu PositionSet.this.to.determine.the.position.of.the.menus.on.the.screen.

Blank ScreenSet.this.to.determine.what.appears.on.screen.when.the.projector.is.searching.for.a.valid.input.source.

Auto Power OffSet.this.to.On,.if.you.want.the.projector.to.go.into.Standby mode.when.no.input.source.is.detected.for.20.minutes.

Auto Power OnSet.this.to.On,.if.you.want.the.projector.to.start.up.imediately.when.the.mains.is.connected.

Set.this.to.Off,.if.you.want.the.projector.to.go.into.Standby mode.when.the.mains.is.connected..In.this.case,.the.projector.will.not.start.up.until.the.POWER.button.is.pressed.on.the.control.panel.or.the.remote.control.

•

•

•

•

••




System Menucontinued

Rear ProjectionSet.this.to.On.to.reverse.the.image.from.left.to.right,.for.use.in.Rear.Projection.Mode.

Ceiling ModeSet.this.to.On.to.reverse.the.image.from.top.to.bottom,.for.use.in.Ceiling.Mode.

Lamp PowerSet.this.to.Economy.to.run.the.lamp.at.reduced.power.

•

•

•




The Trigger outputs can be used to automatically control the screen or screen shuttering. See the Connection Guide for more information.

To set what a ‘blank’ screen looks like, use the Blank Screen setting in the System menu.

Control Menu

Keys 1 to 5The. .to. ..keys.on.the.remote.control.can.each.be.programmed.to.switch.to.one.of.the.input.sources.

Trigger 1 and 2Choose.from.Screen,.Aspect Ratio.or.RS232,.to.determine.what.will.cause.each.Trigger output.to.activate.

Auto-SourceWhen.this.is.set.to.On,.the.projector.will.search.for.an.alternative.input.source.when.the.current.input.source.is.disconnected

When.this.is.set.to.Off,.the.projector.will.show.a.‘blank’.screen.when.the.current.input.source.is.disconnected.

•

•

••


Page 1�Rev A August 2011


Service MenuInformation

Service MenuFactory Reset

Do NOT do this unless you are sure that you want to restore ALL the current settings to their factory defaults.

Service Menu

InformationPress.ENTER/SELECT.to.view.information.about.the.projector,.eg:

Factory Reset

Press.ENTER/SELECT.to.restore.all.settings.to.their.factory.defaults.

When.the.warning.message.appears,.use. .or. to.select.YES.or.NO,.then.press.ENTER/SELECT.to.confirm.your.selection.

•

••




Service Menucontinued

Blue OnlySet.this.to.On.to.display.only.the.blue.component.of.the.input.signal,.for.calibration.or.test.purposes.

Test Patterns

Use. .or. to.select.from.a.range.of.test.patterns.

Press.MENU.to.return.to.the.menu,.or..ENTER/SELECT.to.return.to.the.currently.selected.input.signal.

AltitudeWhen.this.is.set.to.Auto,.the.internal.fan.will.operate.at.Low.speed,.and.rise.to.High.speed.automatically.if.the.internal.temperature.rises.

When.this.is.set.to.High,.the.fan.will.operate.at.High.speed.continuously,.for.use.at.high.altitude.locations.

•

••

••

Digital Projection M-Vision Cine 3D series 3. MENU MAP Operating Guide


Menu MapMenu Sub Menus and Controls

MAINAspect Ratio 1�:9, Theaterscope, �:�, �:� Narrow, NativePresets

Recall..A, B, C, D, DefaultSave..A, B, C, D

BrightnessContrastSaturationHueSharpnessNoise ReductionOverscan Off, Crop, ZoomInput Select all available inputsResync Projector will re-synchronise with the current input signal3D Settings

3D.Enable..Off, On3D.Type..SBS Dual, L-R DualDLP.Link..Off, OnL-R.Swap..Normal, Swap

ADVANCEDColor Space Auto, YPbPr, YCbCr, RGB PC, RGB VideoGamma Film, Video, Punch, Graphics, CRTColor Temperature ��00K, ��00K, ��00K, 9�00K, NativeColor Gamut Auto, REC�09, SMPTE-C, EBU, NativeBrilliantColor On, OffAdaptive Contrast On, OffFine Sync V Position, H Position, Phase, Tracking, Sync LevelRGB Adjust RGB Offset and Gain

Notes

Some of the information in this menu map is summarised. See the actual menu on the projector for full detail.


Where it would be helpful, some menu options are described in more detail earlier in this operating guide.

Digital Projection M-Vision Cine 3D series 3. MENU MAP Operating Guide


SYSTEMLanguage English onlyMenu Position Top Left, Top Right, Bottom Left, Bottom Right, CentreBlank Screen Logo, Black, Blue, WhiteAuto Power Off On, OffAuto Power On On, OffRear Projection Off, OnCeiling Mode Off, OnLamp Power Standard, Economy

CONTROL1 Key all available inputs2 Key all available inputs3 Key all available inputs4 Key all available inputs5 Key all available inputsTrigger 1 Screen, 1�:9, Theaterscope, �:�, �:� Narrow, RS2�2Trigger 2 Screen, 1�:9, Theaterscope, �:�, �:� Narrow, RS2�2Auto Source On, Off

SERVICEInformation Model Name, Serial Number, Software Version, Active Source, Signal Format, Pixel Clock, H⁄V Refresh Rate, Lamp HoursFactory Reset Projector will ask for confirmation before restoring all settings to factory defaultsBlue Only Off, OnTest Patterns Off, White, Black, Red, Green, Blue, Cyan, Magenta, Yellow, Chequer GridAltitude Auto, High

Menu Sub Menus and Controls Notes

Some of the information in this menu map is summarised. See the actual menu on the projector for full detail.


Where it would be helpful, some menu options are described in more detail earlier in this operating guide.

Documents

M-Vision Cine 3D series - ProjectorCentral · Digital Projection M-Vision Cine 3D series 1. USING THE MENUS Operating Guide Rev A August 2011 Page 2 Using the Menus Use.the.buttons.on.the.projector.control