M-Series - Power · PDF fileM-Series - Inch Machine Screw Jack 4 Performance of Standard M-Series Inch Machine ... 1.5 1430 820 0.202 0.129 66 1.5 M1805 M1804 ... 1.5 M1820 M1819 20

Inch Machine Screw Jack

Inch Ball Screw Jack

Inch Stainless Steel Machine Screw Jack

M-SeriesScrew Jacks

M-Series - Inch Machine Screw Jack

Inch / Imperial Machine Screw Jacks2

1www.powerjacks.com

Advantages

• Positive, Mechanical Positioning

• Uniform, Lifting Speed

• Multiple Arrangements

• Anti-Backlash Feature (optional)

Ca pacities from 1/4 Ton to 250 To nWorm Gear Ratios from 5:1 to 50:1

The imperial machine screw jack range is produced in many standard models with a wide range of capabilities, there is a standardmodel for almost any requirement.

Operated manually or by motor units imperial jack models can be used singly, in tandem or in multiple arrangements Since most capacities have a uniform lifting speed, added economy can be realised in raising unevenly distributed loads byoperating the different capacities in unison.

Most imperial machine screw jack models with higher ratios are self-locking and will hold heavy loads in position indefinitely withoutcreep, in ideal conditions. However if self-locking is critical, a brake motor or other restraining device should be considered. They can beused to push, pull, apply pressure and as linear actuators. They are furnished with standard raises in increments of 1 inch. Dependingupon size and type of load, models are available with raises up to 25 feet.

Bottom Pipe Protects liftingscrew threads.

Shell CapLocked in place by set screws.

Lifting ScrewAvailable with threaded end orclevis end instead of top plate.

Load BearingsBearings, top and bottom

to take loads in tension orcompression.

Worm GearAluminium bronze.

Accurately hobbed for greater gear contact.

WormAvailable with double

or single shaft extension.

Thrust Bearingsand Grease SealsAt each end of worm.1/4 & 1/2 ton modelsdo not have seals.

Housing Aluminium on 1/4 to 1 ton models,ductile iron on 2 ton through15 ton models, cast steel on20 ton through 250 ton models.

Top PlateMust be bolted to lifting member to preventy rotation except when screw is keyed.


More Than 200 Standard Combinationswww.powerjacks.com


Inch / Imperial Machine Screw Jacks1

3

Features• Precise Positioning - Can be controlled accurately for positioning within thousandths of a millimetre.

• Self-Locking - Will normally hold loads in position without creeping when using the higher ratio units, as long as thescrew jack unit is not subject to vibration. If self-locking is critical a brake motor or other restraining device should beconsidered.

• Uniform Lifting Speed - Since many models have the same gear ratios, various capacities can be used in the sameapplication to lift unevenly distributed loads with uniform speed.

• Quick, Sure Operation - Designed and built to be positive acting, for accurate response to motive power.

Options• Anti-Backlash Option - Reduces vertical backlash between the screw and the worm gear nut to a practical

minimum for smooth, precise operation and minimum wear.

• Keyed Option - Stops a translating screw from rotating when the screw ends are free.

• Bellows Boot Option - Protects the screw from dust, dirt, moisture and corrosive contaminants.

• Double Clevis End Option - Incorporates a special clevis end bottom pipe and a standard clevis end on thelifting screw.

Note Clockwise rotation of worm raises load on all models (refer to previous page) - counter clockwise available atextra charge.Unless a translating lifting screw is keyed, the top should be bolted to the lifting member to prevent the screwfrom rotating.Screw jacks are equipped with “Alemite” grease fittings.Recommended lubricants are listed in the installation and maintenance instructions.Screw jacks supplied complete with drive shaft keys.

Attachments

Nema C-Face flanges, motors, gear boxes, reducers and couplings available for single screw jack drive or multiple screw jack arrangements

Motion control components include motor drives, Motion Controllers with operator interfaces, encoders, limit switches, potentiometersand meters with LCD display

Upright Screw Rotating Screw (Upright)Available in both upright

and inverted types

Inverted ScrewThreaded

Clevis


Performance of Standard M-Series Inch Machine Screw Jacks 4

1www.powerjacks.com

M2501

M2500

1

0.75

0.2

Acme

5:1

20:1

25

100

0.5

0.25

55

25

0.245

0.140

5

0.27

M1802 &

M9002M1801

&M9001

2

1

0.25

Acme

6:1

24:1

24

96

2

0.5

120

50

0.232

0.133

17

0.33

M2555

M2554

0.25

0.5

0.25

Acme

5:1

-

20

-

0.333

-

13

-

0.330

-

2.33

0.1

Upright

Inverted

Diameter

Pitch

Form

Standard

Optional

Standard

Optional

Standard

Optional

Standard

Optional

Standard

Optional

Capacity (Short Tons)

Model

Screw JackEfficiency

Weight with BaseRaise of 6” (lb)

Weight for eachAdditional I” Raise (lb)

M2625

M2624

0.5

0.625

0.125

Acme

5:1

-

40

-

0.333

-

21

-

0.200

-

2.33

0.1

M1815

M1814

15

2.25

0.5

Square

8:1

24:1

16

48

5

1.5

1430

820

0.202

0.129

66

1.5

M1805

M1804

5

1.5

0.375

Square

6:1

24:1

16

64

4

0.75

450

185

0.221

0.121

35

0.85

M1810

M1809

10

2

0.5

Square

8:1

24:1

16

48

5

1.5

950

490

0.220

0.140

52

1.4

M1825

M1824

M9035

M9034

M9075

M9074

25

3.375

0.666

Square

32:1

16

48

8

2.5

3360

1900

0.164

0.092

181

3.5

M1820

M1819

20

2.5

0.5

Square

8:1 10 2 3:1 10 2 3:1 10 2 3:1 10 2 3:1

24:1

16

48

5

1.5

2050

1170

0.188

0.120

93

2.6

M1850

M1849

50

4.5

0.666

Square

32:1

16

48

15

6

7500

4200

0.138

0.083

410

5.5

35

3.75

0.666

Acme

32:1

16

48

8

2.5

4000

2400

0.158

0.089

240

3.7

75

5

0.666

Square

32:1

16

48

15

6

12000

6600

0.124

0.075

650

6.5

M1899

M1898

100

6

0.75

Square

12:1

36:1

16

48

25

11

16000

8600

0.130

0.080

1200

9

M18150

M18149

150

7

1

Square

12:1

36:1

12

36

25

11

28100

15500

0.141

0.086

1350

12.6

M2250

M2249

250

9

1

Square

50:1

-

50

-

35

-

20000

-

0.080

-

2700

23

Lifting Screw

Note: For loads from 25% to 100% of screw jack capacity, torque requirements are approximately proportional to the load.

Raises, measured in increments of one inch, are available up to 20 feet, depending on lifting screw diameter and available bar stock length.

Worm GearRatios

Turns ofWorm for I” Raise

Start-UpTorque at FullLoad (in.lb)

Max. HP perScrew Jack


Translating Screw Jack Dimensions


Performance of Standard M-Series Inch Machine Screw Jacks www.powerjacks.com

15

Inch Screw Jacks with Numeric Controls Ratios

1 to 25 Ton screw jacks with Decimal Ratio at no extra cost.

Numeric Control Ratios 100 Turns = 1” of Travel

Note: 1. All other data for these models is the same as main performance table at the top of the page.2. For loads from 25% to 100% of screw jack capacity, torque requirements are approximately proportional

to the load.


Screw Jack Efficiency

Upright

Inverted

Diameter

Pitch

Form

Model M2501

M2500

1

0.75

0.200

Acme

20:1

100

24

0.133

0.25

M1805

M1804

5

1.5

0.250

Acme

25:1

100

175

0.091

0.75

M1810

M1809

10

2

0.250

Acme

25:1

100

370

0.086

1.5

M1815

M1814

15

2.25

0.250

Acme

25:1

100

640

0.075

1.5

M1820

M1819

20

2.5

0.250

Acme

25:1

100

925

0.069

1.5

M1825

M1824

25

3

0.320

Acme

32:1

100

1500

0.053

2.5

M1802 & M9002

M1801 & M9001

2

1

0.250

Acme

25:1

100

48

0.132

0.5

Lifting Screw

Worm Gear Ratios

Turns of Worm for I” Raise

Start-Up Torque at Full Load (in.lb)

Maximum HP per Screw Jack


Translating Screw Jack Dimensions6

1www.powerjacks.com

Not

e1.

All

dim

ensi

ons in

inch

es.

2.D

imen

sion

s sub

ject

to c

hang

e w

ithou

t not

ice.

Upr

ight

A

Inve

rted

CA

A

B

D E

GF

I

HE D

B BB C AH

ISt

yle

2St

yle

3

ST

U VN

O

PR

Q

ZW

XK

J

LM

ST

U

VN

O

PR

Q

Z

W

XK

J

L

M

Styl

e 1

N

O

PR

Q

ZW

XK

J

LM

YY

X

Y

Styl

e 4S

TU

VN

O

PR

Q

ZW

XK

J

M

Y

LU

ST

X

VN

O

PR

Q

Z

W

X

K

J

M

Y

L

U

Styl

e

3.LH

S =

Left

Han

d Si

de4.

RH

S =

Rig

ht H

and

Side


Translating Screw Jack Dimensions


Translating Screw Jack Dimensions www.powerjacks.com

17

Mod

el

Styl

e

Upr

ight

Cap

acity

(Sh

ort

Ton

s)In

vert

ed

Upr

ight

Inve

rted

Upr

ight

Inve

rted

Dia

met

er

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z A-A B-B

No

of H

oles

M25

55M

2554

0.25 1 0.5 1

5 /16

21/4

5 /16

41/2

21/4

9 /32 4 2 31/4

15/8

11/8

1.5

9 /32 4 23/8

23/8

M26

25M

2624

M25

01M

2500

M18

02M

1801

M90

02M

9001

M18

05M

1804

M18

10M

1809

M18

15M

1814

M18

20M

1819

M18

25M

1824

M90

35M

9034

M18

50M

1849

M90

75M

9074

M18

99M

1898

M18

150

M18

149

M22

50M

2249

0.5 1

0.62

5

15 /

16

21/4

5 /16

41/2

21/4

9 /32 4 2 31/4

15/8

11/8

1.5

9 /32 4 23/8

23/8

1 1 0.75 1.5

3 /8

31/2

3 /8 6 3

13/3

2

5 21/2 4 2

17/1

6

2.5

7 /16 4 31/4

31/4

2 2 1 1.75 1 /2

41/4

7 /16 7 3.5

13/3

2

7 3.5 6 3 31/2

13/4 2 1 11/8 3

13/3

2

441

/16

33/4

2 3 1 1.75 1 /2

41/4

7 /16 7 3.5

13/3

2

41/8

21/1

6

31/8

19/1

6

61/4

2.42

51/4

1.93

11/8 3

13/3

2

441

/16

33/4

5 3 1.5

2.25 1 /2

41/2

5 /8 9 4.5

11/1

6

6 3 41/2

21/4 8 3 61/2

2.25

111 /

32

311

/16

4 51/4

43/4

10 3 2 2.25 1 /2

53/4

3 /4

11 5.5

13/1

6

7.5

33/4

53/4

27/8

83/4

27/8 7 2

123 /

32

4.13

13/1

6

4 55/8 5

15 3 2.25

2.75 5 /8

53/4

3 /4

11 5.5

13/1

673

/437

/8 6 3 91/4

33/8

71/2

2.5

123 /

32

4.13

13/1

6

465

/16

51/2

20 3 2.5

3.25 3 /4

53/4

3 /4

11 5.5

11/8

81/4

41/8 6 3 11 41/8

83/4 3 13/8

4.13

13/1

6

4 71/8

71/8

25 3

3.37

5

4 1 81/2 1 14 7 13/8

101 /

4

51/8

71/2

33/4

133 /

4

51/8

11 3.75

23/1

6

611

/16

4 87/8

87/8

35 3 3.75 4 11/4

101 /

2

15/1

6

14 7 15/8

10.2

551

/871

/233

/415

1 /2

6 12.5

4.5

23/1

6

7.75

15/8 4 87/8

87/8

50 2 4.5

4.75

11/4

111 /

4

11/4

22 11 17/8

193 /

4

97/8

16 8 93/4

47/8 6 3

45/1

6

8.75

13/8 4

107 /

8

107 /

8

75 2 5 5.5

13/8

111 /

4

13/8

24 12 21/8

14 7 10 5 23 9.5

19 7.5

41/8

10.2

51.

5 613

9 /16

139 /

16

100 4 6 6 11/2

1421

5 /16

23 11.5

17/8

241 /

2

121 /

4

20 10 203 /

4

8 81/8

5.75

37/1

6

11 17/8 6 17 17

150 4 7 6 11/2

1421

5 /16

23 11.5

17/8

24.5

121 /

4

20 10 203 /

4

8 81/8

5.75

41/4

11 17/8 6 17 17

250 5 9 9 21/2

2431

5 /16

48 24 23/4

41 201 /

2

35 17.5

291 /

2

14.7

520

1 /2

11 101 /

2

16 23/4 6

231 /

8

231 /

8

RA

ISE D

A+

3 /4

A+

3 /4

7 /8

7 /8

15/1

612

1 /32

121 /

3223

/827

/827

/831

/241

/241

/259

/16

65/8

78

11

0.37

5+0

.000

-0.0

02

0.37

5+0

.000

-0.0

02

0.50

0+0

.000

-0.0

02

0.50

0+0

.000

-0.0

02

0.50

0+0

.000

-0.0

02

0.75

+0.0

00-0

.002

1+0

.000

-0.0

02

1+0

.000

-0.0

02

1+0

.000

-0.0

02

1.37

5+0

.000

-0.0

02

1.37

5+0

.000

-0.0

02

1.5

+0.0

00-0

.002

1.75

+0.0

00-0

.002

1.75

+0.0

00-0

.002

1.87

5+0

.000

-0.0

02

3+0

.000

-0.0

02

0.93

8+0

.003

-0.0

00

0.93

8+0

.003

-0.0

00

1.25

+0.0

03-0

.003

1.70

3+0

.001

-0.0

01

1.70

3+0

.001

-0.0

01

2.18

8+0

.002

-0.0

00

2.59

8+0

.003

-0.0

00

2.59

8+0

.003

-0.0

00

2.59

8+0

.003

-0.0

00

3.75

+0.0

05-0

.000

3.75

+0.0

05-0

.000

5.31

3+0

.003

-0.0

00

5.31

3+0

.003

-0.0

00

7.5

+0.0

03-0

.000

7.5

+0.0

03-0

.000

13+0

.005

-0.0

00

1 /8

x 1 /

163 /

4 LN

G1 /

8 x

1 /16

3 /4

LNG

1 /8

x 1 /

16 1

LN

G1 /

8 x

1 /16

1 L

NG

1 /8

x 1 /

16 1

LN

G3 /

16 x

3/3

2 1

1 /4

LNG

1 /4

x 1 /

8 1

1 /2

LNG

1 /4

x 1 /

8 1

1 /2

LNG

1 /4

x 1 /

8 1

1 /2

LNG

5 /16

x 5

/32

2 L

NG

3 /8

x 3 /

16 2

1 /4

LNG

3 /8

x 3 /

16 2

1 /4

LNG

1 /2

x 1 /

4 3

LN

G1 /

2 x

1 /4

3 L

NG

3 /4

x 3 /

8 5

LN

G0.3

13 x

0.15

62

LNG

4 2

A+

3 /4

A+

3 /4

A-1

/8A

-1/8

A-1

/4A

A-1

/8A

-1/8

A A4 2

4.5

1.25

5.25

1.75

5.25

1.75

7 2.5

A-1

/8A

-1/8

A-1

/8A

-1/8

A-1

/2A

-1/2

A AA A-1

7.25

2.75

8 2.75

9.25 3

11 312 4

A-3

/8A

-3/8

13 3.5

A-1

/2A

-1/2

16.5

5.5

A+/

-1/4

A+/

-1/4

24 12

A-1

/2A

-1/2

24 12

A-2

A+

1 /2

30 12

AS

REQ

UIR

ED

--

- --

-- -

--

--

-

Not

eD

imen

sion

s are

sub

ject

to c

hang

e w

ithou

t not

ice .


Rotating Screw Jack Dimensions8

1www.powerjacks.com

For other dimensions and performance data refer to translating screw model. All dimensions in inches.

Upright Rotating Screw

Inverted Rotating Screw

Note: Dimensions subject to change without notice.

ModelUM

UM2556UM2626UM2502UM1803UM9003UM1806UM1811UM1816UM1821UM1826UM9036UM1851UM9076UM1897UM18151

Capacity(Short Tons)

0.250.5122510152025355075100150

Style

Raise + 1.5 5/85/8

2 3/8 7/87/8

3/8 9/329/323/8

6

2 3/83 1/4

5 1/45 5/86 5/167 1/88 7/8 3 1/88 7/810 7/813 9/16

1 1/81 1/16

4 1/164 1/16

5/8

A B D E F GHoles Dia. P.C.D

H J KI

Raise + 1 7/8Raise + 1.5

Raise + 2 3/8Raise + 2 3/8

Raise + 3Raise + 4Raise + 4Raise + 5Raise + 7

Raise + 8.5Raise + 8

Raise + 9.75

Raise + 7Raise + 6

111233333332244

0.750.75122

44.5

2.53

3.5

55.5

C

1717

000000 4

66.5

8.59

14

11

1.7522

2.52.55

3.5

0.3120.4370.5

0.6250.625

1

1.51.249

1.752.53

3.5

54

5.5 8.75

1.51.51.52.5333

5.55.5

7.57

0.50.50.50.75

111

1.251.5222

2.5

2.252.253.253.253.25

7.5

1012.5

15.5

444

44

6

44444

4

66

6

9/160.810.81

1 1/161 1/16

1 1/8

13/3213/3213/32

2 3/82 3/82 3/8

2 7/82 7/83 1/20.94

1 1/161 1/8

1.5

1.751.75

3

55.56.5 4.5 4.5

4.55.566 5/8

4.5

781011

12.5

6

89

11

1.51.51.523

3.53.75

5

7

000000

78

000000000

0

22

C'

ModelDM

DM2556DM2626DM2502DM1803DM9003DM1806DM1811DM1816DM1821DM1826DM9036DM1851DM9076DM1897DM18151


0.250.5122510152025355075100150

Style

Raise + 1.5 5/85/8

2 3/8 0.3120.437

7/8 9/329/327/8

3.5

2 3/83 1/4

5 1/45 5/86 5/167 1/88 7/88 7/810 7/813 9/16

4 1/164 1/16

5/8

A B D E F GHoles Dia. P.C.D

H K LJ

Raise + 1 7/8Raise + 1.5

Raise + 2 3/8Raise + 2 3/8

Raise + 3Raise + 4Raise + 4Raise + 5Raise + 7


Raise + 9.75

Raise + 7Raise + 6

111233333332244

0.750.75122

44.5

2.53

3.5

55.5

C

1717

3/83/80.255/85/82 0.75

11

1.251.5

2

1.130.810.631.50.882 5/83 5/8

22

2 3/82 3/83 1/44 1/164 1/165 1/4

6 1/25 5/8

7 7/89 7/89 7/8111/2

18151/16

17 5.5

0.50.6250.625

11.2491.51.752.53

45

1.51.51.52.5333

5.55.56

7.57

8.75

3/83/80.50.50.5

1

22

2.5

I

46

6.5

8.59

14

2.252.253.253.253.25

7.5

1012.5

15.5

444

44

6

44444

4

66

6

9/160.810.81

1 1/161 1/16

1 1/8

13/3213/3213/32

2 3/82 3/82 3/8

02 7/84.50.94

1 1/161 1/8

1.5

1.751.75

3

55.56.5 4.5 4.5

4.55.566 5/8

4.5

781011

12.5

6

89

11

1.51.51.523

3.5033.75

5

7

000000

78

DiaJ

Pilot

BDShellAdjustable

Shell Cap

Dia

Lifting Nut

Lifting Nut

E

A CF

G DiaH

Mounting Plate

Bottom Pipe

MountingPlate

K

Pilot

BD

ShellAdjustableShell Cap

F Dia

AG

DiaK

Top Pipe

Dia L

J

DiaI

H

EC

I


Standard Translating Screw End Fittingswww.powerjacks.com

19


Rotating Screw Jack Dimensions

Note 1. All dimensions in inches.2. Dimensions subject to change without notice.

B

A

E

C

D(Closed Height)

BASE

OF

SCR

EW JA

CK

GI I

FH

K(Closed Height)

BASE

OF

SCR

EW JA

CK

M2555

M2554

0.25

3/8-24

UNF-2A

0.5

0.75

4

2

1/8

13/64

3/8

0.5

0.375

4

2

Upright

Inverted

DIA

Upright

Inverted

Upright

Inverted

Model

A

B

C

D

E

Clevis End

F

G

H

I

K


M2625

M2624

0.5

3/8-24

UNF-2A

5/8

1

4

2

1/8

17/64

0.5

5/8

0.5

4

2

M2501

M2500

1

1/2-13

UNC-2A

0.75

0.75

5 3/8

2

1/8

21/64

0.5

0.75

0.375

5

1 5/8

M1802

M1801

2

3/4-10

UNC-2A

1

1 1/8

6

2.5

1/8

13/32

0.75

1

0.75

5.25

1.75

M9002

M9001

2

3/4-10

UNC-2A

1

1 1/8

6

2.5

0.19

13/32

0.75

1

0.75

5.25

1.75

M1805

M1804

5

1-8

UNC-2A

1.5

1 1/8

8

3.5

0.19

21/32

1

1.5

1

7

2.5

M1810

M1809

10

1 1/2-6

UNC-2A

2

1 5/8

8.75

4.25

0.25

25/32

1.25

2

1.25

7.5

3

M1815

M1814

15

1.75-5

UNC-2

2.25

2

9.75

4.25

0.25

29/32

1.5

2.25

1.25

8.5

3

M1820

M1819

20

2-4.5

UNC-2A

2.5

2.25

11.5

5

0.25

1 1/32

1.75

2.5

1.5

10

3.5

Upright

Inverted

DIA

Upright

Inverted

Upright

Inverted

Model

A

B

C

D

E

Clevis End

F

G

H

I

K


M1825

M1824

M9034

M9034

25

3-4

UNC-2A

3.375

3.25

13.75

5.75

0.25

1 9/32

2.25

3.375

1.75

12

4

35

3.25-4

UNC-2A

3.75

3.75

15

7

0.25

1 17/32

2.5

3.75

2

13

5

M9075

M9074

M1850

M1849

50

4-4

UNC-2A

4.5

4.25

17.5

8

0.25

1 25/32

3.25

4.5

2.5

15

5.5

75

4-12

UNC-2A

5

4.5

20.5

9.5

0.25

2 1/32

3.5

5

2.5

18

7

M1899

M1898

100

4 1/2-12

UNC-2A

6

5

25

12

0.25

2 17/32

4.25

6

3

24

9

M18150

M18149

150

5-12

UNC-2A

7

5

25

12

0.25

2 25/32

5.25

7

3

24

9

M2250

M2249

250

8-12

UNC-2A

9

6

30

12

0.25

3 17/32

7

9

4

30

12

Threaded End

Threaded End


Double Clevis Screw Jacks10

1www.powerjacks.com

Note For other performance and dimension information refer to translating screw models.

Note 1. All dimensions in inches unless otherwise stated.2. Dimensions subject to change without further notice.

Model CCM2555

CCM2625

CCM2501

CCM1802

CCM1805

CCM1810

CCM1815

CCM1820

CCM1825

CCM9035

CCM1850

0.251

5.54

1.5-

1 1/163/8

13/64

5.75500

5.75

ABCDEFG

Capacity (Short Tons)Style

Max Allowable Raise(compression) at load (lb)

Max Raise at RatedLoad (compression)

0.51

5.54

1.5-

1 1/160.5

17/64

9.251000

9.25

12

6.55

1.5-

1 5/160.5

21/64

9.751500

8.25

23

6.755.251.50.75

1 21/320.750.41

14.53000

12 1/8

549721

2.381

0.66

22.56500

17

104

10.257.52.751.252.881.250.78

3112000

22 7/8

154

11.258.52.751.252.881.50.91

37 3/816000

25 7/8

204

13.5103.51.53.51.751.03

39.2520000

29.25

25416124

1.754.52.751.28

5438000

47

354171342

4.52.51.53

73.561000

69

50519154

2.55 9/163.25

1 25/32

94.598000

90.5

Style 1

B

Style 2

Style 3 Style 4

Style 5

Raise

Raise + A

Raise + C

DD

E

FGStandard Clevis


Anti-Backlash Screw Jackswww.powerjacks.com

111


Double Clevis Screw Jacks

M-Series machine screw jacks with anti-backlash nuts for applications where a reversal of loading fromtension to compression is encountered. These are based on the 1800 and 9000 series screw jacks and aredesignated 4800 and 9400 series.

Anti-Backlash Features

• Reduction in the vertical backlash between the screw and the worm gear nut to apractical minimum for smoother, more precise operation and minimum wear.

• Acts as a safety device, providing a dual nut load carrying unit, when the worm gearbecomes worn.

• Wear indicator for critical applications.

The anti-backlash feature can be maintained by adjusting the shell cap until the desired amount of backlash isachieved. To avoid binding and excessive wear, do not adjust lifting screw backlash to less than 0.005".

Standard Dimensions (inches)

Torque and Efficiencies for Standard Anti-Backlash Screw Jacks

Note For loads from 25% to 100% of screw jack capacity, torque requirements are proportional to the load.

Model

Capacity, Short Tons

Start-Up Torque at Full Load (in.lb)

M4555

M4554

0.25

15

-

0.277

-

2.5

Upright

Inverted

Std Ratio

Option 1

Std Ratio

Option 1

M4625

M4624

0.5

24

-

0.168

-

2.5

M4501

M4500

1

60

27

0.212

0.117

6

M4802

M4801

2

135

56

0.196

0.119

18

M4805

M4804

5

500

228

0.199

0.109

37

M4810

M4809

10

1005

526

0.198

0.126

55

M4815

M4814

15

1658

904

0.180

0.110

70

M4825

M4824

25

3712

1997

0.134

0.083

197

M9435

M9434

35

5083

3014

0.137

0.077

250

M4850

M4849

50

8022

4542

0.124

0.073

440

M9475

M9474

75

13204

7314

0.113

0.068

750

M4899

M4898

100

17004

9210

0.117

0.072

1325

M48150

M48149

150

31330

17225

0.127

0.077

1475

M4820

M4819

20

2261

1228

0.176

0.108

101

EfficiencyRating

Weight with Base Raiseof 6" (lbs)

ModelM4555M4625M4501M4802M4805M4810M4815M4820M4825M9435M4850M9475M4899M48150

A445

5.257

7.258

9.5121314

18.526.526.5

ModelM4555-KM4625-KM4501-KM4802-KM4805-KM4810-KM4815-KM4820-KM4825-KM9435-KM4850-KM9475-KM4899-KM48150-K

E1.51.251.062.252.753.383.634.05.56.57.07.58.510

0.750.810.751.251.75

22

1.52.252.38

345

5.56

1.51.251.52.252.753.383.63

45.56.57.07.58.510

I222

1.752.52.752.75

3345

6.51212

0.750.810.750.630.881.131.251.01.251.253.04.05.05.56

B2.382.883.843.885.435.756.137.759.699.4411.7515.2518.0618.06

Keyed C

2.382.433.383.885.435.756.137.759.699.4411.7515.2518.0618.06

Raise + 0.75Raise + 0.75Raise + 1.63Raise + 0.75Raise - 0.25

RaiseRaise


Raise + 1.75Raise + 1.75

Raise + 1Raise + 0.5Raise + 0.5

FRaise + 0.75Raise + 0.75Raise + 1.13Raise - 0.13Raise + 0.38

RaiseRaise

Raise + 0.75Raise

Raise + 0.69Raise + 0.75

Raise + 1Raise + 1Raise + 1

Shell Cap

Upright

Inverted

Upright

Inverted

B

C

A

F

E

I

Anti-Backlash Keyed Anti-Backlash


Bellows Boots Screw Protection12

1www.powerjacks.com

• Protects the screw from dust and dirt.

• Helps maintain the proper lubrication.

• Guards against moisture and corrosive contaminants.

• Boots are made of neoprene-coated nylon with sewn construction.Other materials are available for applications involving hightemperatures, highly corrosive atmospheres and other specialconditions.

Boot Installation Data

Note: For horizontal installation exceeding 18" of travel, internal bootguides are recommended.

Upright Imperial Machine Screw Jacks with Bellows Boots

ModelNo

M2555

M2625

M2501

M1802

M9002

M1805

M1810

M1815

M1820

M1825

M9035

M1850

M9075

M1899

M18150

M2250

4.25

4.25

6.0

7.75

7.75

7.75

9.0

9.0

9.0

10.75

11.0

14.5

16.5

11.25

12.25

16.0

A

4

4

41/2

51/4

51/4

7

71/4

8

91/4

11

12

13

171/2

24

24

30

B

4

4

5

61/2

61/2

7

81/2

81/2

10

12

13

15

19

24

24

-

0-12" 12"-18" 18"-24" 24"-30"

Raise

30"-36" 36"-48" 48"-60" 60"-72"

C

41/4

41/2

53/8

71/4

71/4

8

93/4

93/4

111/2

133/4

15

171/2

211/2

25

25

-

A

43/4

41/4

51/8

53/4

51/4

7

71/4

8

91/4

11

12

13

171/2

24

24

30

B

45/8

45/8

55/8

71/2

71/2

81/2

81/2

10

11

12

13

16

19

24

24

-

C

5

41/2

6

81/4

81/4

91/2

93/4

111/4

121/2

133/4

-

181/2

211/2

25

25

-

A

-

41/4

51/2

53/4

53/4

7

71/4

8

91/4

11

12

13

171/2

24

24

30

B

-

45/8

53/4

71/2

71/2

81/2

91/2

10

11

131/4

13

16

19

24

24

-

C

-

41/2

61/4

81/4

81/4

91/2

103/4

111/4

121/2

15

15

181/2

211/2

25

25

-

A

-

-

-

53/4

53/4

8

81/2

9

101/2

12

12

14

171/2

24

24

301/2

B

-

-

-

71/2

71/2

81/2

91/2

10

12

131/4

133/4

16

19

24

24

-

C

-

-

-

81/4

81/4

91/2

103/4

111/4

131/2

15

153/4

181/2

211/2

25

25

-

A

-

-

-

61/4

61/4

8

81/2

9

101/2

12

12

14

171/2

241/2

241/2

301/2

B

-

-

-

81/2

81/2

10

91/2

10

12

141/2

133/4

17

19

241/2

243/8

-

C

-

-

-

91/4

91/4

11

103/4

111/4

131/2

161/4

153/4

191/2

211/2

251/2

253/8

-

A

-

-

-

-

-

9

91/2

11

111/2

13

127/8

15

181/2

25

25

311/2

B

-

-

-

-

-

10

101/2

12

13

153/4

143/4

18

20

251/2

251/8

-

C

-

-

-

-

-

11

113/4

121/4

141/2

171/2

163/4

201/2

201/2

261/2

261/8

-

A

-

-

-

-

-

-

101/2

11

121/2

14

133/4

16

191/2

26

26

311/2

B

-

-

-

-

-

-

111/2

12

14

153/4

151/2

18

21

261/2

267/8

-

C

-

-

-

-

-

-

123/4

131/4

151/2

171/2

171/2

201/2

231/2

271/2

267/8

-

A

-

-

-

-

-

-

111/2

12

131/2

15

143/4

17

201/2

27

27

32

B

-

-

-

-

-

-

121/2

13

15

163/4

161/2

19

22

271/2

265/8

-

C

-

-

-

-

-

-

133/4

141/4

161/2

181/2

181/2

211/2

241/2

281/2

275/8

-

BootO.D.

Capacity

Shell CapDiameter "A"

25 Ton

7.5

35 Ton

7.875

50 Ton

11.25

75 Ton

13.25

100 Ton

10

150 Ton

10

250 Ton

16

Capacity


500 lb

2.25

1000 lb

2.25

1 Ton

2.75

2 Ton

3.5

5 Ton

4.5

10 Ton

5.25

15 Ton

5.625

20 Ton

6

Note 1. (-) indicates "not applicable".2. For lengths of raise not detailed in the above table consult Power Jacks Ltd.3. Dimensions subject to change without notice.4. All dimensions in inches.

A

A B C

Top Plate Clevis End Threaded End


Bellows Boots Screw Protection


Bellows Boot Screw Protectionwww.powerjacks.com

113

Inverted Machine Screw Jacks with Bellows Boots

Finding minimum closed dimensions

• Add your structure thickness X1 to A, B, or C from the appropriate chart to find the minimum closed dimension.

• Other styles and sizes of boots can be supplied.

• In order to use a standard boot, make the mounting plate diameter the same as the shell cap diameter of theappropriate screw jack

• When boots are required for rotating screw jacks, consult Power Jacks Ltd.

Raise (Inches)

Model No

M2554

M2624

M2500

M1801 & M9001

M1804

M1809

M1814

M1819

M1824

M9034

M1849

M9074 a,b,c

M1898

M18149

A

2

2

2 1/16

2 3/8

3 3/16

3 1/4

3 1/4

3 1/4

3 3/8

4 1/2

4 7/8

2 3/8

* 7 11/16

* 7 11/16

B

2 3/8

2 5/8

3

4 3/8

4 3/16

5 3/4

5 1/4

5 9/16

6 3/4

7 1/2

9 5/16

6 7/8

* 8 11/16

* 8 11/16

2

2 1/8

2 5/8

3 5/8

3 3/16

4 1/2

4

4 1/16

5

5 1/2

6 13/16

4 7/8

** 7 11/16

** 7 11/16

A

2

2

2 1/16

2 3/8

3 3/16

3 1/4

3 1/4

3 1/4

3 3/8

4 1/2

4 7/8

2 3/4

* 7 11/16

* 7 11/16

A

2 1/8

2 1/8

2 11/16

2 7/8

3 3/16

3 1/4

3 1/4

3 1/4

3 3/8

4 1/2

4 7/8

3

* 7 11/16

* 7 11/16

A

3 1/16

3

3 1/2

3 9/16

3 9/16

3 1/4

3 3/8

4 1/2

4 7/8

3 3/8

* 7 11/16

* 7 11/16

B

4

5 3/8

5 11/16

7

6 3/4

6 9/16

7 3/4

7 1/25/16

7 7/8

* 8 11/16

* 8 11/16

3

4 5/8

4 11/16

5 3/4

5 1/2

5 1/16

6

5 1/2

7 13/16

5 7/8

** 7 11/16

** 7 11/16

B

2 3/8

2 5/8

3

4 3/8

4 3/16

5 3/4

5 1/4

5 9/16

6 3/4

7 1/2

9 5/16

7 1/4

* 8 11/16

* 8 11/16

B

3 1/4

3 5/8

5 3/8

5 11/16

5 3/4

6 3/4

6 9/16

6 3/4

7 1/25/16

7 1/2

* 8 11/16

* 8 11/16

2 3/4

3 1/4

4 5/8

4 11/16

4 1/2

5 1/2

5 1/16

5

5 1/2

7 13/16

5 1/2

** 7 11/16

** 7 11/16

C

2

2 1/8

2 5/8

3 5/8

3 3/16

4 1/2

4

4 1/16

5

5 1/2

6 13/16

5 1/4

** 7 11/16

** 7 11/16

1"-6" 7"-12" 13"-18" 19"-24"

Top Plate Clevis End Threaded End

1898 - 18149 only

A

X1

B

X1

C

X1

A

X1

XX

XX

Value of X = a) If A+X1 is less than 5 1/2”, X = 5 1/2” b) If B+ X1 is less than 9 1/2”, X = 9 1/2” c) If C+ X1 is less than 7”, X = 7”

*If A+X1 and B+ X1 are less than 12”, X = 12”. If greater than 12”, use dimensions shown.

** If C+ X1 is less than 9”, X = 9”. If greater than 9”, use dimensions shown.

Dia as required

Mounting Plate

12.7 mm (1/2”)

To be manufactured by installer

Note Same values can be used forM4800 Series Screw Jacks Units.

Note 1. For lengths of raise not detailed in the above table consult Power Jacks Ltd.2. Dimensions subject to change without notice.4. All dimensions in inches.


Worm Flange Bolt Dimensions14

1www.powerjacks.com

Note For other performance and dimension information refer to translating screw models .

A

45o

45o

B 60o

60o

Model

M2555

M2625

M2501

M1802 & M9002

M1805

M1810

M1815

M1820

M1825

M9035

M1850

M9075

M1899

M18150

M2250

'B' Bolt P.C.D. (inch)

-

-

-

1 11/16

2 3/8

2 3/4

2 3/4

3 1/2

4 1/8

4 1/4

5 1/4

5 3/4

6 1/4

6 1/4

8 1/4

Bolt Information

No Flange Bolts

No Flange Bolts

No Flange Bolts1/4 - 20 x 3/4" Long5/16 - 18 x 3/4" Long5/16 - 18 x 3/4" Long5/16 - 18 x 1" Long

3/8 - 16 x 1 1/4" Long3/8 - 16 x 1 1/4" Long1/2 - 13 x 1 1/4" Long5/8 - 11 x 1 1/2" Long5/8 - 11 x 1 1/2" Long5/8 - 11 x 1 1/2" Long5/8 - 11 x 1 1/2" Long

3/4 - 10 x 2" Long

-

-

-

A

A

A

A

A

A

A

A

B

B

B

B

Conf

Configuration

iguration A Configuration B

Note 1. All dimensions in inches unless otherwise stated.2. Dimensions are subject to change without notice .


Worm Flange Bolt Dimensions


Motor Adapters for Inch Screw Jackswww.powerjacks.com

115

Rotary limit switches can be used as end of travel limit switcheswith the option of intermediate switches as well. These units aremounted onto a screw jacks free worm shaft and offer analternative where bottom pipe mounted limit switches are notpossible e.g. rotating screw jacks. Up to 8 limit switches can beaccommodated in one unit.

For mounting details please consult Power Jacks.

The mounting kit includes the flexible coupling and driveadaptor.

A* Ref

ØC

B

RLS-51 Rotary Limit Switch Adapters

Motor Adaptors for Inch Screw Jacks

• Standard adaptors for inch screw jacks available on request.

• Designed for standard IEC frame sizes.

• Allows direct motor coupling on either side of the screw jack input shaft.

• Complete with drive coupling and mounting hardware.

• NEMA frame size versions available on request.

• Adaptors for other mounting arrangements available on request.

Note: When direct coupling a motor to an a screw jack , it is necessary to match motor power to screw jack load so the motor does not exceed the maximum screw jack power.


SKA Rotary Limit Switch Adaptors16

1www.powerjacks.com

Typical top view showing switchmounted on RH worm extensionPosition Number of Switch

75, 100 & 150 TonsImperial models only

2

1 3

4

2

1

3

4

Capacity(Short Ton)

Screw Jack

2 & 3510152025355075100150

1C

2A & B

AAAA

3RH LH RH

Extended Mount Closed MountLH

B & DDDD

4-CCCCCCCC

-CCCCCCCC

1 2 3 4 1-

-

----

2-

A & BA & BA & BA & B

BB

3-DDD

4---------

1-DDD

----

2-

A & BA & BA & BA & B

BB

3-

-

4---------

CB & DDDD

A & BAAAA

Note For 2 & 3 Ton inverted position, extended mount position (2) is the only one practical.(A) Special Closed Height. (B) Boot Interference Unit. (C) Rotary Limit Switch extends below base of screw jack.(D) Sealed electric elbow would extend below base of screw jack ( ) Recommended. ( - ) Not RecommendedExtended Mount is Standard.

The SKA rotary limit switch is a compact 2-position limit switch designed for screw jack and linear actuator applications.

Note 1. All dimensions are in inches unless otherwise stated.2. Dimensions are subject to change without notice.

3”

1/2” NPT

3 9/16”

6 5/8”

6 1/4”

Actuator Mounted


SKA Rotary Limit Switch Adaptors


Mounting and Adjustment for SKA Rotary Limit Switcheswww.powerjacks.com

117

CClosed

Mount (inch)

-5.56.257 1/86 7/8

7 13/32

8 1/16

8 1/16

9 5/810.7511 1/32

11 1/32

BExtended

Mount (inch)

6.756.757.758.758.758.7510.2510.2514.2515.2514.7514.75

ACut-off ClosedMount (inch)

-1 9/32

1 17/32

1 21/32

1 29/32

1 3/82 7/32

2 7/32

4 21/32

4.53.753.75

Model(ShortTon)

23510152025355075100150

DWorm ShaftDia. (inch)

0.5000.6250.7501.0001.0001.0001.3751.3751.5001.7501.7501.875

A4mm

(0.157”)4mm

(0.157”)

Drill 7.9mm (5/16”) Diax 9.5 mm (3/8”) Deep

D

Drill 2.38mm (3/32”) DiaThro’ for Spring Pin

BC

- Extended Mount- Closed Mount

Spacers as requiredExtended Mount only

Adaptor Plate

Optional Remote ScrewPosition Analog Indicator Standard 1/2” x 14 TPI

Note Shim out on limit switch if necessary worm shaft end must not rub switch housing. Dimensions subject to change without notice.

Note 1. All dimensions are in inches unless otherwise stated.2. Dimensions are subject to change without notice.

SKA Limit Switch Field Installation Dimensions

C Lifting ScrewL

M-Series - Stainless Steel Screw Jack

Inch / Imperial Stainless Steel Machine Screw Jacks18

2www.powerjacks.com18 www.powerjacks.com

Lifting Screw316 Stainless Steel.

Also available as threadedend or clevis end.

Shell Cap316 Stainless Steel.

Locked into place byset screws.

Load BearingsCarbon Steel Bearings, top

and bottom to take loads intension or compression.

Worm GearAluminium Bronze.

Accurately hobbed forgreater gear contact.

Worm316 Stainless Steel standard.

Available with doubleor single shaft extension.

(17-4 Ph available as special)

Worm Bearingsand SealsBoth ends of worm.316 Stainless Steel caseand spring.

Bottom Pipe316 Stainless Steel.Protects lifting screw threads.

Housing316 Stainless Steel.

Guide BushingBronze.

Nitrile Rubber SealsTop and bottom with316 Stainless Steelcase and spring protectsgear housing fromcontamination.

Top Plate316 Stainless Steel.Must be bolted to liftingmember to preventrotation except whenkeyed.

Advantages

• Capacity from 2 Tons through to 100 Tons.

• Worm gear ratios from 6:1 to 36:1

• Corrosion resistant.

• Stainless steel hardware.

• Sealed gear cavity keeps water and other contaminants out.

• Anti-Backlash models available.

• Available with keyed lifting screws for translating screw models.

• Available in upright and inverted rotating screw models withtravelling nut.

• Can be retrofitted into applications where non-stainless steel screw jacks have been previously used.

Optional Features

• Closed heights

• Materials

• Lifting screw ends

• With Stop Nuts

• Worm shaft extensions

• W ith bellows boots

• Lifting screw thread pitches


Inch / Imperial Stainless Steel Machine Screw Jacks


Performance of Standard Inch Stainless Steel Screw Jackswww.powerjacks.com

219www.powerjacks.com 19

SM-1802

SM-1801

2

0.66

1

0.250

Acme

6:1

24:1

24

96

21/2

40

17

0.232

0.133

19

SM-1805

SM-1804

5

1.66

1 1/2

0.375

Square

6:1

24:1

16

64

43/4

150

60

0.221

0.121

37

SM-1810

SM-1809

10

3.33

2

0.500

Square

8:1

24:1

16

48

5

1 1/2

250

135

0.237

0.151

55

SM-1815

SM-1814

15

5.00

2 1/4

0.500

Square

8:1

24:1

16

48

5

1 1/2

475

275

0.202

0.129

70

SM-1820

SM-1819

20

6.66

2 1/2

0.500

Square

8:1

24:1

16

48

5

1 1/2

685

390

0.188

0.120

96

SM-1825

SM-1824

25

8.33

33/8

0.666

Square

10 2/3:1

32:1

16

48

8

2 1/2

665

400

0.164

0.092

168

SM-9035

SM-9034

35

11.66

3 3/4

0.666

Acme

10 2/3:1

32:1

16

48

8

2 1/2

1335

800

0.156

0.089

250

SM-1850

SM-1849

50

16.66

4 1/2

0.666

Square

10 2/3:1

32:1

16

48

15

6

2500

1400

0.138

0.083

420

SM-1899

SM-1898

100

33.33

6

0.750

Square

12:1

36:1

16

48

25

11

5335

2865

0.130

0.080

1260

Upright

Inverted

Sustaining

Operating**

Diameter

Pitch

Form

Std. Ratio

Optional

Std. Ratio

Optional

Std. Ratio

Optional

Std. Ratio

Optional

Std. Ratio

Optional

Screw Jack Model


Start-Up Torqueat OperatingLoad* (In.-lbs)

EfficiencyRating

Lifting Screw

Worm GearRatios

Turns of Wormfor 1" Raise

Max. HP perScrew Jack

Weight with Base Raise of 6" (lbs)

* For Loads 25% to 100% of screw jack capacity, torque requirements are approximately proportional to load.** Screw jack has been de-rated for 316 Stainless Steel worm. For full load rating use 17-4 PH worm.


Inch Stainless Steel Screw Jack Dimensions20


Mod

elN

o

SM-1

802

SM-1

805

SM-1

810

SM-1

815

SM-1

820

SM-1

825

SM-9

035

SM-1

850

SM-1

899

Sust

aini

ng

2 5 10 15 20 25 35 50 100

Ope

ratin

g

0.66

1.66

3.33

5.00

6.66

8.33

11.6

6

16.6

6

33.3

3

Cap

acity

(Sho

r t To

ns)

S 3.5

8.00

8.75

9.25

11.0

0

13.7

5

15.5

0

9.75

20.7

5

R 1.75

3.00

2.88

3.38

4.13

5.13

6.00

4.88

8.00

T 3.5

4.50

5.50

5.50

5.50

7.00

7.00

11.0

0

11.5

0

V 1.12

1.50

1.80

1.80

1.50

2.30

2.10

4.40

3.40

X .41

.69

.81

.81

.81

1.06

1.62

1.38 *

Y 3.00

3.00

4.13

4.13

4.13

6.00

7.75

8.75 *

Z .41

.69

.81

.81

1.12

1.38

1.62

1.88 •

a .75

1.19

1.31

1.38

1.75

2.13

2.63

3.25 *

b 1.5

.75

.88

.88

1.13

1.38

1.38

1.88 *

Keys

eat

(b x

h x

L)

.125

x 0

.060

x 1

.00

LG

.188

x .0

94 x

1.2

5 LG

.250

x .1

25 x

1.5

0 LG

.250

x .1

25 x

1.5

0 LG

.250

x .1

25 x

1.5

0 LG

.313

x .1

56 x

2.0

0 LG

.313

x .1

56 x

2.0

0 LG

.375

x .1

88 x

2.2

5 LG

.500

x .2

50 x

3.0

0 LG

U 7.00

9.00

11.0

0

11.0

0

11.0

0

14.0

0

14.0

0

22.0

0

23.0

0

Q 7.00

6.00

7.50

7.75

8.25

10.2

5

10.2

5

19.7

5

24.5

0

P 3.5

3.00

3.75

3.88

4.13

5.13

5.13

9.88

12.2

5

N 2.00

6.50

7.00

7.50

8.75

11.0

0

12.5

0

6.00 *

M 1.00

2.25

2.00

2.50

3.00

3.75

4.50

3.00 *

H .50

.60

.94

.94

.94

.94

1.31

1.25

2.94

.500

.749

1.00

0

1.00

0

1.00

0

1.37

5

1.37

5

1.50

0

1.75

0

+.00

0-.0

02

+.00

0-.0

02

+.00

0-.0

02

+.00

0-.0

02

+.00

0-.0

02

+.00

0-.0

02

+.00

0-.0

02

+.00

0-.0

02

+.00

0-.0

02

D .50

.50

.50

.63

.75

1.00

1.25

1.25

1.50

G 4.25

4.50

5.75

5.75

5.75

8.50

10.5

0

11.2

5

14.0

0

F 1.66

2.38

2.88

2.88

3.50

4.50

4.50

5.63

7.00

L 6.00

4.50

5.75

6.00

6.00

7.50

7.50

16.0

0

*

K 3.00

2.25

2.88

3.00

3.00

3.75

3.75

8.00 *

J

1.70

2

2.18

8

2.59

8

2.59

8

2.59

8

3.75

0

3.75

0

5.31

3

7.50

0

+.00

3-.0

00

+.00

3-.0

00

+.00

3-.0

00

+.00

3-.0

00

+.00

3-.0

00

+.00

3-.0

00

+.00

3-.0

00

+.00

3-.0

00

+.00

3-.0

00

WE

1.75

0

±.00

5

2.25

0

±.00

5

2.25

0

±.00

5

2.75

0

±.00

5

3.25

0

±.00

5

4.00

0

±.00

5

4.00

0

±.00

5

4.75

0

±.00

5

6.00

0

±.00

5

B 4.56

5.88

6.00

6.31

8.00

9.75

9.56

11.3

8

18.5

0

A 5.50

7.50

7.75

8.00

10.2

5

11.7

5

12.5

0

13.5

0

24.0

0

C

Trav

el

Trav

el

+3 /

8

Trav

el

+1 /

4

Trav

el

+1 /

2

Trav

el- 1

/ 4

Trav

el

+1 /

4

Trav

el

+1 /

4

Trav

el

Trav

el

+1 /

2

Mod

el S

M18

99 (

100

Ton)

Mou

ntin

g H

ole

Pat

tern

Not

e:1.

Dim

ensi

ons a

re s

ubje

ct to

cha

nge

with

out n

otic

e .3.

Dim

ensi

ons in

inch

es.

5.R

HS

= R

ight

Han

d Si

de2.

For m

odel

s SM

1802

and

SM

-185

0 st

yle

as p

er s

ectio

n 1.2

.3.2

.4.

LHS

= Le

ft H

and

Side

D

E

GH

B

A(C

lose

dH

eigh

t)

C

F

Lift

ing

Scre

wT

QP

LK

V

SW

U

Key

Sea

t

JN

RM

Four

Hol

es “

Z”

Dia

“a”

Dia

Spo

tfac

e

“b”

Rad

ius

Four

Hol

es “

X”

Dia

equ

all y

spac

ed o

n “Y

” D

ia P

.C.

RH

SLH

S

Six

hole

s 1.

88”

Dia

equa

lly s

pace

d on

11”

P.C

. Dia

8.13

”

8.13

” 5.75

”

10.0

”20

.0”

Six

Hol

es 1

.85 ”

Dia

3.50

” D

ia S

potf

ace


Inch Stainless Steel Screw Jack Dimensions


Inch Stainless Steel Screw Jack Dimensionswww.powerjacks.com


Model No

SM-1802

SM-1805

SM-1810

SM-1815

SM-1820

SM-1825

SM-9035

SM-1850

SM-1899

A*

5 1/4"

7"

7 1/2"

8 1/2"

10"

12"

13"

15"

24"

B*

1 3/4"

2 1/2"

3"

3"

3 1/2"

4"

5"

5 1/2"

9"

C3/4"

1"

1 1/4"

1 1/4"

1 1/2"

1 3/4"

2"

2 1/2"

3"

E3/4"

1"

1 1/4"

1 1/2"

1 3/4"

2 1/4"

2 1/2"

3 1/4"

4 1/4"

D13/32"21/32"25/32"29/32"

1 1/32"

1 9/32"

1 17/32"

1 21/32"

2 17/32"

F

6.0

8.0

9.25

10.25

12.5

14.5

15.5

18.0

25.0

G

2 1/2"

3 1/2"

4 1/4"

4 1/4"

5"

5 3/4"

7"

8"

12"

H J

1 1/8"

1 1/8"

1 5/8"

2"

21/4"

3 1/4"

3 3/4"

4 1/4"

5"

N

5.25

7.5

7.75

8.5

10.25

11.75

12.5

13.5

24.0

UNC-2A

UNC-2A

UNC-2A

UNC-2A

UNC-2A

UNC-2A

UNC-2A

UNC-2A

UNC-2A

P

1 3/4"

2 1/2"

2 3/4"

2 3/4"

3"

3"

4"

3 1/2"

12"

3/4

1 1/2

1 3/41/2

2 1/2

3 1/4

4 1/2

Standard Stainless Steel Screw Jack Screw End Dimensions

Note 1. * Closed height dimensions may increase for screw jack units supplied with bellows boots. Consult Power Jacks Ltd.2. Lifting screw listed above are not keyed. Must be held to prevent rotation.3. Keyed lifting screws and keyed anti-backlash models are also available. Consult Power Jacks Ltd.4. All dimensions in inches.5. Dimensions are subject to change without notice .

E

D JCC

A

B

F

G

H

P

NUpright

Std Top Plate

Inverted

BASE OF SCREW JACK

M-Series - Inch Ball Screw Jack

Inch / Imperial Ball Screw Jacks22

3www.powerjacks.com22 www.powerjacks.com22 www.powerjacks.com

Shell CapAdjustable to take end playout of bearings. Locked into

place by set screws.

Ball NutEquipped with return tubesfor continuous recirculationof steel balls. Threaded and

secured to worm gear. Shouldbe ordered as set.

Worm GearAluminium bronze. Accurately

hobbed for greater gear contact.

WormAvailable with double

or single shaft extension. Clockwiserotation of this end raises load on

all models except 50 tonball screw jacks.

Load BearingsTop and bottom to take loads

in either direction.

Bottom PipeProtects lifting screw threads.

Lifting ScrewStandard with threaded end.

Thrust Bearingsand Grease SealsAt each end ofworm. 1/2 tonmodels do nothave seals.

Stop-DiscThis is not a power stop. Forpositive stop we suggest externalstops be used in structure.

HousingAluminium on 1/2 ton models,ductile iron on 2 ton through10 ton models, cast steel on20 ton through 50 ton models.

Advantage s• Move Loads and apply force more efficiently than machine screw jacks.• Permit faster operation and longer life under load.• Require less power by providing positive mechanical action.• Permit synchronisation of multiple units.• Capacity from 1/2 to 50 tons (4.5 kN to 450 kN).• Handles full load in tension or compression.• 40 models available.

The M-Series ball screw jack gives you a single-package, positive action screw jack which can be driven by an electric, air or hydraulicmotor. A ball-bearing type heat-treated screw and mating nut with rolling contact reduces friction to a bare minimum in convert ingtorque to thrust. Overall operating efficiency is as high as 70% in some models, depending on the worm gear ratio.

M-Series ball screw jacks are available as translating or rotating screws in either upright or inverted configurations. In the translatingscrew type, the ball nut is fixed to the gear and the lifting screw moves up and down through the nut. In the rotating screw type, thescrew is fixed to the gear and the ball nut travels along the screw.

Depending on size and type of load, models are available with raises up to 10 feet (3 metres). Raises up to 20 feet (6 metres) areavailable on request. Ball screw jacks may be used individually, in tandem or in multiple arrangements. Special models are availableand there is no extra charge for single ended worm shafts extensions.


Inch / Imperial Ball Screw Jacks


Inch Ball Screw Jack Modelswww.powerjacks.com

323www.powerjacks.com 23www.powerjacks.com 23

Features

• High Speed - Low friction permits linear motion in some models up to 300 inches/min (7.62 m/min) at 1800 rpm wormshaft speeds, providing maximum horsepower ratings are not exceeded.

• Precise Positioning - Can be controlled accurately for positioning within thousandths of an inch.

• Positive Action - Operates with a high degree of reliability, without the need for costly pumps, hoses or valves

• Long-Life - Low friction means longer operating life.

• Low Power Usage - Highly efficient design means less power is needed to achieve a given thrust; power needs aremuch as two-thirds that of machine screw jacks.

Options

• 3 Standard Gear Ratios - Wide selection of gear ratios, increases the amount of raise rates available.

• 2 Ball Screw Lead Options - On the 2, 5 and 10 ton models there is the option of either the standard or a 1“(25.4 mm) lead for rapid raise rates.

• Screw on Ends - The standard screw jack has a threaded end to which clevis or top plates can be screwed. Note: these items are shipped loose and must be spot drilled before seating set screws in field installations.

• Bellows Boot Option - Protects the screw from dust, dirt, moisture and corrosive contaminants.

• Double Clevis End Option - Incorporates a special clevis end bottompipe and standard clevis end on the liftingscrew.

Note:

Attachments

IEC and Nema C-Face flanges, motors, gear boxes, reducers and couplings available for single screw jack drive or multiple screw jackarrangements

Motion control components include motor drives, Motion Controllers with operator interfaces, encoders, limit switches, potentiometersand meters with LCD display

Translating Screw(Upright)

Rotating Screw (Upright)Available in both upright

and inverted typesTranslating Screw

(Inverted)

Note A brake is required onM2800 and M9800screw jack units dueto their high efficiency.

Clockwise rotation of worm raises load on all models (refer previous page) except 50 ton ball screw jack

counter clockwise available at extra charge.

The lifting screw end should be bolted to the lifting member to prevent the screw from rotating.

Screw jacks are equipped with "Alemite" grease fittings.

Recommended lubricants are listed in the installation and maintenance instructions.

Screw jacks supplied complete with drive shaft keys.


Performance of Standard M-Series - Inch Ball Screw Jacks24


M2860M2859

5041

10 2/3:132:1

-10.66

32-

156-

27001500

-22001200

-0.680.41

-520

5

9233-

Model

Capacity (Short Tons)Lifting Screw(Inches)

WormGear Ratios

Turns of Wormfor 1" Raise

Maximum HPper screw jack

Starting Torqueat Full Load (in.lb)

Running Torqueat Full Load (in.lb)

Efficiency Rating

Weight with Baise Raiseof 6" (lbs)Weight for each additional1" Raise (lbs)Hold Back Torqueat Rated Load(ft.lb)

M2825M2824

253

0.6610 2/3:1

32:1-

16.1648.48

-8

2 1/2-

925475

-825425

-0.600.39

-235

2.9

242-

M2820M2819

202.250.58:124:1

-1648-5

1 1/2-

700325

-650300

-0.610.44

-115

1.5

242-

M28003M28002

31 11/640.4136:124:112:1

14.52658.10429.052

21/23/411050681004560

0.660.370.5521

0.42

70.52

M28631M28630

0.55/80.25:120:1

-25100

-1/31/6-

10.55-

9.54.5-

0.670.35

-2.75

0.1

10.5-

M2805M2804

51.5

0.4746:124:1

-12.66750.667

-4

3/4-

22090-

18080-

0.700.39

-40

0.85

80.5-

UprightInverted

DiameterLeadStandardOption 1Option 2StandardOption 1Option 2StandardOption 1Option2StandardOption 1Option 2StandardOption 1Option 2StandardOption 1Option 2

StandardOption 1Option 2

M2810M2809

101.5

0.4748:124:1

-16.88850.667

-5

1 1/2-

350175

-300150

-0.630.42

-50

0.85

110.5-

M2802 & M9802*M2801 & M9801*

21

0.256:124:112:12496482

1/23/4502530452025

0.590.330.5320

0.33

20.51

M28021 & M98021*M28011 & M98011*

211

6:124:112:1

624122

1/23/418080135160701050.660.380.5120

0.33

20.51

M28051M28041

51.51

6:124:1

-624-4

3/4-

500206

-410183

-0.650.36

-40

0.85

80.5-

M28101M28091

101.51

8:124:1

-824-5

1 1/2-

800400

-700290

-0.570.46

-50

0.85

110.5-

* Dimension same as model M2802 and M28021.

Note Lifting screws listed above are not keyed. Must be held to prevent rotation. Hold Back Torque is restraining torque atthe worm shaft to keep load from running down. Lifting torques are proportional to load, down to 25% ofrated load.


Performance of Standard M-Series - Inch Ball Screw Jacks


Performance of Standard M-Series - Inch Ball Screw Jackswww.powerjacks.com


Model

Capacity (Short Tons)100% Full Load75% Full Load50% Full Load or Less

M28021&M98021

21253001000

M28003

32506502200

M2805

5100025009000

M28051

550010004000

M2825

2570020006000

M2810

101003501000

M28101

1050150500

M2820

201503501200

M2860

5060015005000

M2802&M9802

250150500

M28631

0.540012003500

Model

LeadAB (Radius)C

M28021&M98021

1.0001.1041.1941.5 Sq.

M28003

0.4131.5871.386

2.125 Dia.

M2805 &M2810

0.4741.9811.69

2.625 Dia.

M28051 &M28101

1.001.7181.72

2.625 Dia.

M2825

0.6603.3493.076

4.751 Dia.

M2820

0.5002.5612.272

3.75 Dia.

M2860

1.0004.0293.756

5.88 Dia.

M2802 &M98020.2501.1041.1941.5 Sq.

M28631

0.2000.8220.7971 Sq.

Life Expectancy of Inch Ball Screw and Ball Nut

Predicting screw and nut life lets you forecast necessary replacement, saving time and money. It also permits selection of the mosteconomical screw size.

Use caution when installing the ball screw. The life expectancy listed below may be greatly reduced if ball screws are subjected tomisalignment, shock loads, side thrust, environmental contamination or lack of lubrication maintenance.

It is possible to estimate the minimum life of the ball screw and nut only. Because of the many variable operatingconditions, we can not accurately predict the life of the worm and gear set in the 2800 and 9800 Series screw jacks. Consult Power Jacks Ltd for advice.

Life in Thousands of Inches Travelled

Note 5 Ton and 10 Ton models use the same screw and nut.

Imperial Ball Nut Return Tube Dimensions

Note: All dimensions in inches.

Radius

C

B

A


Inch Ball Screw Jack Dimensions26


Plan View

AJ

C

B

AA

H

DFG

E

AA

A

B

F

S

T

V

N

O

P

Q

R

W

X

K

L

M

Models:

M9802, M98021, M2805, M28051, M2810,M28101, M2820, M2825.

E

X

U

Models:

S

T

V

N

O

P

Q

R

W

X

K

L

M

U

Y

NW

X

K

L

M

OP

Q

R

Y

X Y

I

Model:

M28631

RHS

LHS

Note LHS = Left Hand SideRHS = Right Hand Side

RHS

LHS

RHS

LHS

M2802, M28021, M28003, M2860.


Inch Ball Screw Jack Dimensions


Inch Ball Screw Jack Dimensionswww.powerjacks.com


Standard M-Series Translating Ball Screw Ends

F

Top Plate Clevis End N

C

D

BA

EL

K

JI

H

G

M

SCR

EW JA

CK

BA

SE

SCR

EW JA

CK

BA

SE

M9802 & M98021

M9801 & M980112

A + 0.757.5

1 3/81

1 21/320. 5

1.75 ± 0.0053/4-16UNF-2A

1 1/87

3.50.500 / 0.498

1/8 X 1/16 X 14 1/82 1/163 1/81 9/166 1/42 7/165 1/4

1 15/161.705 / 1.702

1 1/813/325 5/8

M28003 M280 & M2801

M280 & M2801

M2810 & M28101

M2809 & M28091

M2820

M2819

M2825

M2824

M2860

M2859

M28631

M28630 M280023

A + 0.759.251 3/8

1 11/641 21/32

0. 51.75 ± 0.005

3/4-16UNF-2A1 1/8

73.5

0.625 / 0.6233/16 X 3/32 X 1

73.563

3.51.75

21

1.706 / 1.7011 1/813/327.25

5

A + 210.751 3/81.5

2 3/80. 5

2.25 ± 0.0051-14UNS-2A

1 1/89

4.50.749 / 0.747

3/16X3/32X1.2563

4.52.25

83

6.52.25

2.190 / 2.1881.5

11/168.75

10

A + 110 3/8

1.51.5

2 7/80.5

2.25 ± 0.0051-14UNS-2A

1 1/8115.5

0.999 /0.9971/4 X 1.8 X 1.5

7.53.755.752 7/88.752 7/8

72

2.601 / 2.5981.8

13 / 168 3/8

M2802 & M28021

M2801 & M280112

A + 0.757.5

1 3/81

1 21/320. 5

1.75 ± 0.0053/4-16UNF-2A

1 1/87

3.50.500 / 0.498

1/8 X 1/16 X 17

3.563

3.51.75

21

1.705 / 1.7021 1/813/325 5/8

50

A + 2.7525 3/83 5/8

45 9/161.25

4.75 ± 0.0053.25-12UN-2A

2.752211

1.500 / 1.4983/8 X 3/16 X 2.25

19.759 7/8168

9.754 7/8

63

5.316 / 5.3134 7/161 7/821 3/8

0.5

ModelUpright


Inverted

A + 151

5/81 1/165/16

1 ± 0.0033/8-24UNF-2A

0.754.52.25

0.375 / 0.3731/8 X 1/6 X 3/4

42

3.251 5/8

----

0.941 / 0.9381 1/89/32

4

Raise As Required

20

A + 0.7516.52.752.253.50.75

3.25 ± 0.0051.75-12UN-2A

2.25115.5

1.000 / 0.9981/4 X 1/8 X 1.5

8.254 1/8

6311

4 1/88.75

32.601 / 2.598

1.51 1/813

ABCDEFGHIJKLMNOPQ

VWXY

RSTU

AA

25

A + 219.753 1/8

34.51

4 ± 0.0052.25-12UN-2A

2.25147

1.375 / 1.3735/16 X 5/32 X 2

10.255 1/87.53.7513.755 1/811

3.753.755 / 3.750

2 5/161 3/816.75

Ø 2.25PCD 1.5Ø 0.75

13/16

5/16

Ø 9/32

Ø 0.752.25

10.5

Ø 5/16

0.5625

1 1/16

M

N

M2802 & M28021M28631Ø 4.25PCD 3Ø 1.51 13/16

7/16

Ø 13/32

Ø1.53

1.50.75Ø 1/2

18 5/82 1/27 1/21 7/16

M2805 & M28051 M2805 & M28051 M2810 & M28101Ø 4.25PCD 3Ø 1.51 13/16

7/16

Ø 13/32

Ø 1.53

1.50.75Ø 1/2

18 5/82 1/27 1/21 7/16

M28003Ø 4.25PCD 3Ø 1.51 13/16

7/16

Ø 13/32

Ø 1.53

1.50.75Ø 1/2

110 3/82 1/29 5/16

1 7/16

Ø 5PCD 3.5Ø 1.751.250.625Ø 11/16

Ø1.754.1252.51.25Ø 3/41.2512 1/23 1/810 3/41 7/16

Ø 5.75PCD 4.125

Ø 1.751.3750.75

Ø 13/16

Ø 24.1252.51.25Ø 11.5

12 1/83 1/410 3/81 9/16

M2820Ø 7

PCD 5Ø 2.625

2 5/16

1Ø 13/16

Ø 2.6256.25

31.5

Ø 1 1/41.7519

5 1/416 1/22 13/16

M2825Ø 8.5PCD 6Ø 3.52 5/16

1Ø 1 1/16

Ø 3.58.25

52.5

Ø 1 1/22.7523 1/46 5/819 3/43 3/16

M2860Ø 13

PCD 10Ø 4.52 13/16

1.375Ø 1.5Ø 5

9.1255.252.625Ø 23.7529 1/87 3/8

25 7/16

3 11/16

UprightInvertedUprightInverted

ABCDEFGHIJKL

Model

= =


Rotating Ball Screw Jack Dimensions28


Note For all other dimensions and performance data refer to translating screw models. All dimensions in inches (1" = 25.4 mm).

Upright Rotating Ball Screw Jack

* 1" Lead Screw Models.Inverted Rotating Ball Screw Jack

Note: Dimensions subject to change without notice. * 1" Lead Screw Models.

UM 2826

25Raise+ 102.258 7/81 5/8

02.2502.2489.3952.027.375

825/326.254.751

0

UM 2821

20Raise+ 82.5

7 1/810

1.7501.7486.7061.5825.375

621/324.3753.375

0

UM 28111*

10Raise+ 51

5 5/800

1.0000.9983.651.02

4 15/164

17/324 1/8

2.25 SQR.0

3Raise

+ 3.751.1254 1/167/16

00.7500.7483.3950.8324.24

25/643 7/162.125

0

UM9803

KUM2806

KUM28004

2Raise

+ 3 1/161.1254 1/16

00

0.7500.7482 3/80.6303.25

417/642.75

1.5 SQR.0

5Raise

+ 4 5/81

5 1/400

1.0000.9984.330.895

4 15/164

17/324 1/162.625

0

5Raise+ 41

5 1/400

1.0000.9983.651.02

4 15/164

17/324 1/8

2.25 SQR.0

UM 2861*

50Raise+ 153.25

10 7/81 1/80.753.2503.24812.6252.029.75

61 1/32

85.88

5.5625

UM 2811

10Raise+ 61

5 5/800

1.0000.9984.330.895

4 15/164

17/324 1/162.625

0

2Raise

+ 3 11/161.1254 1/16

00

0.7500.7483 1/320.6303.25

417/642.75

1.5 SQR.0

UM28632

KUM28031*

0.25Raise+ 2

0.6252 3/8

00

0.4370.4351.75

0.531252.625

417/642 3/321 SQR.

0

KUM2803

2Raise

+ 3 1/161.1254 1/16

00

0.7500.7482 3/80.6303.25

417/642.75

1.5 SQR.0

Model


A

BCC’D

E Dia.

FGH Dia.

HolesI Dia.

P.C.DJ Dia.K Dia.

UM98031*

2Raise

+ 3 11/161.1254 1/16

00

0.7500.7483 1/320.6303.25

417/642.75

1.5 SQR.0

A

I

C

B

H

FG

E

J

D

K

Pilot

ShellShell Cap

Mounting Plate

Bottom PipeLiftingNut

KDM 2826

25Raise+ 102.258.8752.5

2.2502.2489.3952.027.375

825/326.254.751

KDM 2821

20Raise+ 82.5

7.1251.6251.7501.7486.7061.5825.375

621/324.3753.375

KDM 28111*

10Raise+ 515

1.1251.0000.9983.651.02

4 15/164

17/324 1/8

2.25 SQR.

KDM28004

3Raise

+ 3.751.1253.75

10.7500.7483.3950.8324.24

25/643 7/162.125

KDM9803

2Raise

+ 3 1/61.1253.750.6250.7500.7482 3/80.6303.25

417/642.75

1.5 SQR.

KDM28006

5Raise

+ 4 5/81

5.250.751.0000.9984.330.895

4 15/164

17/324 1/162.625

KDM 28061*

5Raise+ 41

5.250.751.0000.9983.651.02

4 15/164

17/324 1/8

2.25 SQR.

KDM 2861*

50Raise+ 153.25112.5

3.2503.24812.6252.029.75

61 1/32

85.88

KDM 2811

10Raise+ 615

1.1251.0000.9984.330.895

4 15/164

17/324 1/162.625

KDM 28031*

2Raise

+ 3 5/81.1253.750.6250.7500.7483 1/320.6303.25

417/642.75

1.5 SQR.

DM 286320.25Raise

+ 2 3/80.6252.375

00.4370.4351.75

0.531252.625

417/642 3/321 SQR.

KDM2803

2Raise+ 3

1.1253.750.6250.7500.7482 3/80.6303.25

417/642.75

1.5 SQR.

Model


A

BCD

F Dia.

GHI Dia.

HolesJ Dia.

P.C.DK Dia.

KDM98031*

2Raise

+ 3 5/81.1253.750.6250.7500.7483 1/320.6303.25

417/642.75

1.5 SQR.

Lifting Screw - right hand,single thread on all models

A

I

C B

HK

G

J

D

Pilot

Shell

Shell Cap Mounting BaseLifting Screw - right hand,single thread on all models

C’

LiftingNut

F

KUM28061*


Rotating Ball Screw Jack Dimensions


Double Clevis End Ball Screw Jackswww.powerjacks.com


Note: For other performance and dimension information refer to translating ball screw jacks.

Note 1. All dimensions in inches unless otherwise stated (1” = 25.4 mm).2. Dimensions subject to change without notice.

Style 1

B

Style 2

Raise

Raise + A

Raise + C

D

F

Standard Clevis

Model

Capacity (Short Tons)Style

ABCDEFG

Max. Allowable Raise inCompression at Load (lb)Max Raise At Rated Load (Compression)

CCM9802 &98021

23

11.1258.6252.50.751.625

10.515

380014.5

CCM2860

504

37.12529.125

82.6255.56253.75

263.5

6100047.5

CCM2802 &28021

22

11.1258.6252.50.751.625

10.515

380014.5

CCM28631

0.51

8.256

2.250.5

1.1250.755/167.87510007.875

CCM28003

32

12.87510.375

2.50.751.75

10.515.5420011.5

CCM2805 &28051

53

16.2512.53.751.252.3751.250.75

20.375740016

CCM2810 &28101

10316

12.1253.8751.252.8751.51

20.574009.5

CCM2820

20323194

1.53.51.751.2534.5

2000021.5

CCM2825

253

30.2523.25

72.54.52.751.547

3500037

DiameterRaiseLoad

Style 3 Style 4

D

E

G


Inch Ball Screw Jacks with Bellows Boots30


Features

• Protects the screw from dust and dirt.

• Helps maintain the proper lubrication.

• Guards against moisture and corrosive contaminants.

• Boots are made of neoprene-coated nylon with sewn construction. Other materials are available for applicationsinvolving high temperatures, highly corrosive atmospheres and other special conditions.

Boot Installation Data

Note For horizontal installation exceeding 18" of travel, internal boot guides are recommended.

Upright Inch Ball Screw Jacks with Bellows Boots

Note 1. (-) indicates "Not Applicable".2. For lengths of raise not detailed in the above table consult Power Jacks Ltd.3. All dimensions in inches (1" = 25.4 mm).4. Dimensions subject to change without notice.

Capacity


10 Ton

4.5

20 Ton

7

25 Ton

8.875

50 Ton

9.5

Capacity


1000 lb

2.25

2 Ton

3.5

3 Ton

3.5

5 Ton

5.375A

72"----------

21.50024.25028.375

18"-

7.5007.5007.5007.5009.25010.75010.75010.37510.37516.50019.75025.375

1-12"5.0007.5007.5007.5007.5009.25010.75010.75010.37510.37516.50019.75025.375

60"----------

20.50022.75027.375

48"-----

11.25013.75013.75012.87512.87518.50021.25026.375

Boot O.D.4.506.636.636.636.636.637.507.507.007.009.0011.0012.00

Model No.M28631M2802M28021M9802M98021M28003M2805M28051M2810M28101M2820M2825M2860

Closed Height "B"

24"-

7.5007.5007.5007.5009.25010.75010.75010.37510.37516.50019.75025.375

30"-

8.5008.5008.5008.50010.25012.50012.50011.62511.62516.50019.75025.375

36"-----

10.25012.50012.50011.62511.62516.50019.75025.375

Raise

A B C


Inch Ball Screw Jacks with Bellows Boots


Inch Ball Screw Jacks with Bellows Bootswww.powerjacks.com


Finding minimum closed dimensions (X)

• Add your structure thickness X1 to A, B, or C from the appropriate chart to find the minimum closed dimension.

• Other styles and sizes of boots can be supplied.

• In order to use a standard boot, make the mounting plate diameter the same as the shell cap diameter of theappropriate screw jack.

• When boots are required for rotating screw jacks consult Power Jacks Ltd.

A B

X1

E

X1

C

X1

X X X

Dia as required

Mounting Plate

12.7 mm (1/2”)

To be manufactured by installer

Note 1. For lengths of raise not detailed in the above table consult Power Jacks Ltd.2. Dimensions subject to change without notice.4. All dimensions in inches.

EE

C4 1/45 1/45 1/46 1/86 1/89 3/49 1/210 7/8

19"-24"Model No.

M28630M2801 & M9801

M28002M2804M2809M2819M2824M2859

Raise (inches)

A2

4 3/16

4 3/16

4 3/16

4 3/46 3/45 1/27 1/4

B2

4 5/84 5/85 1/85 1/8

86 3/47 1/4

C2 3/45 1/45 1/46 1/86 1/89 3/49 1/210 7/8

A2 3/84 3/16

4 3/16

4 5/84 3/46 3/45 1/27 1/4

B2 3/84 5/84 5/85 1/85 1/8

86 3/47 1/4

C3 1/45 1/45 1/46 1/86 1/89 3/49 1/210 7/8

A2 3/44 3/16

4 3/16

4 5/84 3/46 3/45 1/27 1/4

B2 3/44 5/84 5/85 1/85 1/8

86 3/47 1/4

1"-6" 7"-12"C

3 3/45 1/45 1/46 1/86 1/89 3/49 1/210 7/8

A3 1/44 3/16

4 3/16

4 5/84 3/46 3/45 1/27 1/4

13"-18"B

3 1/44 5/84 5/85 1/85 1/8

86 3/47 1/4

E.751.51.51.751.5

2.6153.54.5

Std. BootCollar Dia

Inverted Inch Ball Screw Jacks with Bellows Boots


Worm Flange Bolt Dimensions32


45o

45o

B

Model 'B' Bolt P.C.D (inch)

1 11/16

1 11/16

2 3/8

2 3/4

3 1/2

4 1/8

5 1/4

-

Bolt Information

No Flange Bolts1/4 - 20 x 3/4" Long

1/4 - 20 x 3/4" Long

5/16 - 18 x 3/4" Long

5/16 - 18 x 3/4" Long

3/8 - 16 x 1 1/4" Long

5/8 - 11 x 1 1/2" Long

3/8 - 16 x 1 1/4" Long

M28631

M2802 & M9802

M28003

M2805

M2810

M2820

M2825

M2860

Motor Adaptors for M-Series Ball Screw Jacks

Dimensions and details are the same as for M-Series machine screw jacks.

Rotary Limit Swith Adaptors for M-Series Ball Screw Jacks

Dimensions and details are the same as for M-Series machine screw jacks.

3”

3 9/16”

6 5/8”

6 1/4”

1/2” NPT

Note 1. All dimensions in inches (1" = 25.4 mm).2. Dimensions subject to change without notice.


Worm Flange Bolt Dimensions


Page Titlewww.powerjacks.com


Screw Jacks

• E-Series Metric Machine Screw Jacks 5 - 2000kN• E-Series Metric Stainless Steel Screw Jacks 10 - 1000kN• E-Series Metric Ball Screw Jacks 10 - 500kN• C-Series Metric Cubic Machine Screw Jacks 10 - 100kN• S-Series Metric High Performance Screw Jacks 25 - 200kN• Special screw jack designs available up to 35000kN

EMA Linear Actuators

• Machine Screw & Ball Screw• Low load, Medium Duty, High Speed• Dynamic Load Ratings up to 10kN• Linear Speeds up to 5500 mm/min• 3-phase AC, 1-phase AC, and DC types• Special Designs Available

Rolaram Linear Actuators

• Ball Screw & Roller Screw• High load, High Duty, High Speed• Very High Accuracy• Dynamic Load Ratings up to 400kN• Linear Speeds up to 7000 mm/min• 3-phase AC, 1-phase AC, and DC types• Special Designs Available

Spiracon Roller Screws

• High Dynamic Loads up to 1200kN• High Efficiency• High Positional Accuracy• Long Life• Low Maintenance• Low Noise• Robust Design for Harsh Environments• Special Designs Available

Neeter Drive Bevel Gearboxes

• 2-way, 3-way and 4-way Designs• Solid Shaft & Hollow Shaft• Motor Adaptors• Gear Ratios 1:1, 1.5:1, 2:1, 3:1 and 4:1• Torque Ratings up to 3000Nm• Special Gear Ratios and Designs Available

Power Jacks Ltd Balmacassie Commercial Park Ellon, AB41 8BX Scotland (UK) Tel: +44 (0)1358 285100

All information in this document is subject to change without notice. All rights reserved by Power Jacks Limited. May not be copied in whole or in part. ©Power Jacks Limited 2015, Aberdeenshire, Scotland, United Kingdom.

Registered

FPAL

OH 623565

PJ-SJB-M-EN-01

www.powerjacks.com [email protected]

Lifting & Positioning Solutions Power Jacks are specialist industrial engineers providingdesign, manufacturing and services of quality industrial lifting, positioning and load monitoring equipment.Our products are supplied globally across many sectors including Industrial Automation, Energy, Transport, Defence and Civil.

Documents

M-Series - Power · PDF fileM-Series - Inch Machine Screw Jack 4 Performance of Standard M-Series Inch Machine ... 1.5 1430 820 0.202 0.129 66 1.5 M1805 M1804 ... 1.5 M1820 M1819 20