CV-CSMTS-DL Datalux In-Dash Computer Display with VC-2615 Consoleand Datalux Keyboard Mount in Ford Crown Victoria

Mounting Solutions

DL-TX204-MTU Clamshell mounting system for the Datalux TX-200 and 204 Computer features locking adjustablescreen tilt, keyboard tilt, swivel and display latch for quick release. Spring loaded keyboard snaps intoclip for easy insertion, removal, use and operator convenience. Mounts to any motion attachment or assembly

DL-TX204-MTU mounted on VC-2613DCconsole installed in Dodge Charger

DL-TX204-MTU mounted on VC-6010console installed in Chevrolet Impala

CV-CSMTS-DL Datalux In-Dash Computer Display withVC-2615 Console and Datalux Keyboard Mount in Ford Crown Victoria

CV-CSMTS-DLIn-dash tilt and swivel mounting system for Crown Victoria or allows the Datalux TX-200 and 204computer to be mounted in place of the factory radio which can then be relocated under the dash or ina Control-Com console. The mount installs easily in the factory radio slot with no cutting or drilling.Its unique design provides substantially more strength, securely mounting your computer whereyou need it. The CV-CSMTS-DL features 25° locking screen tilt and 12° locking swivel.

DL-TX-SM-KBD and DL-TX-SMMount system for Datalux TX-200 and 204 Tracer tablet with locking display tilt and swivel. 16”articulating arm with Datalux keyboard clip mounted on a TS-1 tilt / swivel. For VC Series consolesand horizontal surfaces. DL-TX-SM available as a display mount only.

DL-TX-SM-KBD mountedon a VC-2613DC vehiclespecific Dodge Chargervertical console on aBASE-L 28” 7ga. steeltunnel plate with a PPJ-HDARM-WF Heavyduty flip-up armrest withPentax PocketJet roll fedprinter mount.

DL-TX-SMMount system for Datalux TX-200 and

204 Tracer tablet only with lockingdisplay tilt and swivel.

DL-TX204-MT2SDatalux TX-200 and 204 Tracer Tablet mount with lockingtilt and swivel for horizontal and some vertical surfaces.

DL-TXADAdapts the Datalux TX-200 and 204 computerto old-style Tracer mounting systems.

DL-KBD-CLPQuick release Datalux keyboard clipattaches to any motion attachmentor keyboard base.

VC-DL-KBDA16” articulating keyboard tray forDatalux Clip-on keyboard.

DL-TRCAD Adapts Datalux Tracer to new-styleTX-204 mounting system.

DL-TX204-MTU on FP-52-ADJ-MDatalux TX-200 Tracer Tablet and Datalux Clip-onkeyboard mount on an FP-52 18”-23” heavy-dutypassenger side floor pole and ADJ-M 8” mediumlength upper with quick-adjust handle. Shownwith pole mounted PPJ-CASE Pentax PocketJetroll or sheet fed mobile printer mount.

DL-TX204-MTU on P5-ADJ-MDatalux TX-200 Tracer Tablet andDatalux Clip-on keyboard mount ona P5B 5” pole bottom and ADJ-M 8”medium length upper with quick-adjust handle. Shown mounted onBASE-S 16” 7ga. steel tunnel platewith universal bolt pattern.

DL-TX204-MTUon F-59-ADJ-MDatalux TX-200 TracerTablet and DataluxClip-on keyboardmount on an FP-59Crown Victoriapassenger side floorpole and ADJ-M 8”medium length upperwith quick-adjusthandle.

New Products 2011 Dodge Charger Mounting Solutions

VH-CHGR112011 Dodge Charger vehicle specific console with 4" vertical and 16"horizontal equipment mounting space. Mounts to OEM vehicle bracketsand has computer attachment point. Includes equipment brackets and fill plates.

Vehicle Specific Consoles

VH-CHGR11VC-2613DC1112" Vertical Console for 2011Dodge Charger. 7.75" front height with 26 degree frontslope and computer attachment point. Includes equipment brackets and fill plates.

VC-2613DC11

Passenger Side Computer MountingFP-CHGR112011 Charger Passenger side computer mount.Requires pole assembly and motion attachment.

FP-CHGR11

Trunk Trays

ST-1516-DC11

SecureStor Gun RackPASS® Police Audio-visual Safety System

Our patent pendingsystem encloses thesiren speakers in theupright of our bumpersystem greatlyimproving groundplane sound in front

of your vehicle. PASS® solves vehicle speaker mounting issuesbecause the speaker is no longer mounted behind the bumperor fascia. With dual speakers, multiple siren tones can be usedindependently and lighting options with front and side LED’s areavailable with a wiring harness for easy installation.

RHT-CHGR11

PASS-2-CHGR11

SS-GM2-CH11SecureStor dual gun rack mountsbehind the front seat on the hump,secured to the front seat bolts andthe rear seat support. The SS-GM2will hold a variety of shotguns andassault rifles. A charging handleguard prevents charging the weaponwhile secured. Slots allow flashlight,radio speakers and other equipmentto be mounted out of the way.

RHT-CHGR11Hinged drop down trunk tray.

ST-1516-DC112011 Charger trunk side equipment tray.

CHGR11-SHELF2011 Charger full width slide-out trunk tray.

CHGR11-TRAY2121" Charger slide-out trunk tray. CHGR11-TRAY-21

New Products

The Lund AR-EXPL11 console installs by removing the factoryarmrest and bucket and dropping it in. The console fits right overthe factory opening and mounts using factory holes. No moving,modifying or cutting is required. There is space for up to 10” ofequipment and accessory mounting. The user friendly design ofthe AR-EXPL11 eliminates the need to mount equipment in variouslocations. A padded armrest is an available accessory as well aspower plus and fuse panels. Constructed of powdercoatedaluminum for structural rigidity, light weight and years of troublefree service, the innovative design of the AR-EXPL11 consoleprovides a clean, functional installation and a finished appearancein 2011 civilian Explorers.

AR-EXPL11 2011 Civilian Explorer Vehicle Specific Console

SS-CGM Cage Mounted GunrackLund’s SS-CGM Cage mounted gun rack features single or dual weaponmounting and locking for long guns. The unit is designed to quickly andsecurely attach to most standard public safety vehicle partitions.The SS-CGM features fully adjustable lock and butt cup locations,allowing for specific weapon and vehicle fit. The SS-CGM isconstructed of powder coated steel for years of trouble free serviceand ease of maintenance, providing a clean and functional installation.Available with or without lock heads.

FP-EXPL11Lund’s FP-EXPL11 passenger side base mounts to the factory seatbolts and requires no drilling into the vehicle floor. The mount includesan FP-STEP offset riser which allows placement of the pole and upperassembly closer to the transmission hump for greater driver comfortand accessibility.

FP-EXPL11 shown withP9-ADJM and Panasonic Toughbookdocking station

New Products PASS ® Police Audio-visual Safety System

PASS® Police Audio visual Safety SystemOur specially designed and patent pending system encloses the siren speaker(s) in the upright of our bumpersystem greatly improving sound on the ground plane in front of your vehicle. PASS® solves speaker mountingissues on new vehicles because the speaker is no longer mounted behind the bumper or fascia. With dualspeakers, multiple sirens and/or tones can be used independently. Multiple lighting options for front and sideLED’s are available with an optional wiring harness for easy installation Currently available for Sedans: Crown Vic, Impala & Charger. SUV’s: Expedition Explorer & Tahoe.

PASS-2-CV PASS-2-IMPL

PASS-2-XL-TAH PASS-2-XL-EXPED

PASS-2-CHGR11

Featured Products SUV Consoles

HC-EXPL2006 - newer Ford Explorer vehicle specificconsole with 14” of equipment space.Includes up to 3 sets of equipment mountingbrackets and fill plates.

HC-ESCP2006 - newer Ford Escape vehicle specificconsole with 17” of equipment space.Includes up to 3 sets of equipmentmounting brackets and fill plates.

HC-HGHD2006 - newer Toyota Highlander vehiclespecific console with 17” of equipmentspace. Includes up to 3 sets of equipmentmounting brackets and fill plates.

VH-TAH2006 - newer Chevy Tahoe vehicle specificconsole with 12” front height, 60 degree slopeand 17” of horizontal and 4” of vertical equipmentmounting space. Includes up to 3 sets ofequipment mounting brackets and fill plates.

Featured Products Consoles

VC-TAH2006 - newer Chevy Tahoe vehicle specificconsole with 13” of equipment space.Includes up to 3 sets of equipmentmounting brackets and fill plates.

HC-160016” low profile 3.75” high Horizontal Console.Includes up to 3 sets of equipment mountingbrackets and fill plates.May require base plate or additional mounting kit.

HC-1600 console with CHB-2EN enclosed cupholder,LSB-400 locking storage box and PB-250 pen box

VC-75066” Vertical Console with 8” front heightand 75 degree slope. Includes equipmentmounting brackets and fill plates.May require base plate or additional mounting kit.

VC-60055” Vertical Console with7” front height and 60degree slope. Includesequipment mountingbrackets and fill plates.May require base plate oradditional mounting kit.

VC-IMPL2006 - newer Chevy Impala vehiclespecific console with 9” of equipmentspace. Includes up to 3 sets ofequipment mounting brackets and fillplates and a seat bolt mounting bracket.

Featured ProductsSS-LGV-1540Aluminum weapon storagebox features a lift-off lid,ventilation holes, electroniccombination lock, easy griphandles and foam liner.Optional pick-and-pull insert(call for details)40”W x 15”D x 7”H

also available:SS-LGV-163636”W x 16”D x 7”H

LGV-1540shown with standard foam insert

LGV-1636shown with optional custom insert.

Both feature anelectronic combinationlock and lift-off lid

UNV-SASM-**Universal latching, swing-away tablet or computerdisplay mount for horizontal or vertical series consoles.Display swings open to allow access to AM/FM radioor other dashboard controls behind.

UNV-SASK3-**Same as above with articulating TG3 keyboard attached.**Specify display bracket when ordering.

VH-75066” Vertical Console with 8” front height and 75degree slope and 3.75” H x 16” L horizontalsection. Includes equipment mounting bracketsand fill plates. May require base plate or additionalmounting kit.

VH-60055” Vertical Console with 7” front height and 60degree slope and 3.75” H x 16” L horizontal sectionIncludes equipment mounting brackets and fill plates.May require base plate or additional mounting kit.

VH-6005 consolewith 16” articulating TG3 keyboard tray

VH-6005 console in Chevy Impala

VH-6005 in Crown Vic with tablet mount and articulating keyboard

VH Tactical Consoles

VH-7506 console withcomputer docking station on SWA-HD-8 and PPJ-HDARM-WF

VH-7506 console

VH Tactical Consoles

VH-CHGRDodge Charger 5” Vertical Console with 7”front height and 60 degree slope and 3.75” Hx 16” L horizontal section. Mounts to OEMvehicle brackets and has computerattachment point. Includes equipmentmounting brackets and fill plates.

VH-CHGR vehicle specificDodge Charger console

VH-CHGR console with tablet and keyboard mountVH-CHGR console installed in 2008 Dodge Charger

VH-6005S New Part

5” Vertical console with 7” front height and60 degree slope and 3.75” high 9” Horizontalsection. Includes equipment mounting bracketsand fill platesMay require base plate or additional mounting kit.

SecureStor heavy duty steel SUV vaults are fully carpeted to protect your equipment and feature a 8.5” highdrawer on heavy duty full extension slides rated to 250 lbs. Dual handles make sliding the drawer easy, andside perforations allow air to circulate keeping out condensation. The units are available with a high securitySimplex combination lock or dual “T” handle locks. SecureStor vaults are powder coated for long life andeasy clean-up and are available to fit Ford Explorer, Expedition and Chevy Suburban/Tahoe, Trailblazer andmany other vehicles. SSTB-SUB-3R: 22” D x 44” W x 23” H (w/ 3”Lip) SSTB-EXPD: 35” D x 44” W x 12” H

SSTB-EXPD-EL: 52” D x 47” W x 12” H

SSTB-CV Ford Crown Vic SecurStor vault mounting kitSSTB-EXPD Ford Expedition SecurStor vault mounting kitSSTB-EXPD-EL Ford Expedition EL SecurStor vault mounting kitSSTB-EXPL Ford Explorer SecurStor vault mounting kitSSTB-SUB Chevy Suburban SecurStor vault mounting kitSSTB-SUB-3R Chevy Suburban 3rd row SecurStor vault mounting kitSSTB-TAH Chevy Tahoe SecurStor vault mounting kitSSTB-UL Flat Floor SecurStor vault mounting kit

Equipment Vaults SecureStor Vaults

SSTB-EXPD-EL installed in Ford Expedition EL

SSTB-EXPDSSTB-SUB-3R

Gun Racks SecureStor Gun Racks

SS-GM2 &SS-FSGM2SecureStor SS-GM2 rear seatdual gun rack mounts behindthe front seat on the humpand is secured to the frontseat bolts and the rear seatsupport member. The SS-FSGM2 mounts to a flat

vehicle floor. Both will hold a variety of shotguns and assault rifles withtheir adjustabilityand ease of installation. A charging handle guard prevents charging theweapon while secured. Slots on the bracket allow flashlight,radio speakers and other equipment to be mounted out of the way.Available with or without gun locks.

SS-GM2-CH Dodge Charger behind the seat dual gunrackSS-GM2-CV Ford Crown Vic behind the seat dual gunrackSS-GM2-EXPD Ford Expedition behind the seat dual gunrackSS-GM2-EXPL Ford Explorer behind the seat dual gunrackSS-GM2-F150 Ford F-150 Quad Cab behind the seat dual gunrackSS-GM2-IMP Chevy Impala behind the seat dual gunrackSS-GM2-TAH Chevy Tahoe behind the seat dual gunrackSS-GM2-SIL Chevy 1500 Quad Cab behind the seat dual gunrack

SS-CGM New Part

Lund’s SS-CGM Cage mounted gun rackfeatures single or dual weapon mounting andlocking for long guns. The unit is designed toquickly and securely attach to most standardpublic safety vehicle partitions. The SS-CGMfeatures fully adjustable lock and butt cuplocations, allowing for specific weapon andvehicle fit. The SS-CGM is constructed ofpowder coated steel for years of trouble freeservice and ease of maintenance, providinga clean and functional installation.Available with or without lock heads.

SS-GM2

SS-FSGM2

LI-900-00013” Console with computermount platform, includes up to3 pairs of equipment bracketsand 6 1/4” fill plate253/4” L x 71/2” W x 8” H

LI-400-00019” Console includes up to 4pairs of equipment bracketsand fill plates (no computer mount platform).24” L x 71/2” W x 8” H

Horizontal and Vertical Consoles

LI-200-0009” Console is designed to fitin smaller areas like in frontof bench seats or in front offactory consoles. Up to 3pairs of equipment bracketsand fill plates are includedand accepts all Control-Comaccessories.14” L x 71/2” W x 8” H

VC-4508Vertical Console has a 45° frontslope and 8” of equipment mounting.The 4508 is computer mount readyand is designed to be directlymounted to the vehicle’s hump orfront seat bolts. 123/4” L x 71/2” W x9” H4500 Series Consoles RequireMounting Kit.

VC-6010Vertical Console has a 60°front slope and 81/4” ofequipment mounting.111/4” L x 71/2” W x 9” H

VC-2613NT12” Vertical Console 10” front heightwith 26 degree front slope and topmount platform. Includes up to 3 setsof equipment brackets and fill plates.17” L x 71/2” W x 10” H

VH-7506 New Part

6" Vertical Console 10" front height with75 degree slope and 3.75" H x 16" Lhorizontal section. Includes equipmentmounting brackets and fill plates.May require Base Plate or additionalmounting kit.

HAT-24M (2” – 4”)

HAT-35 (3” – 5”)

HAT-47 (4” – 7”)Adjustable base mountfor tilt / swivel which can be used to mount computers,keyboards, etc. instead of pole assemblies on consolesand base plates.

CHB-2ENCHB-2CHB-1

SPM-1 CupholdersSingle, double and adjustable

cupholders mount to a variety of surfaces and the rear or inside of Control-Com consoles. Open design allows for easy cleaning and mounting.SPM-1 adjusts from a small 8 oz. coffee cup to fit most big gulps.

ARMP Armrest and ARM-CLFully Padded Armrest or 1/2 PaddedArmrest with microphone clip with 2” to 5” adjustable bracket permits settingthe desired armrest height on console.

FB-66-position fuse block withsingle power feed has 150

amp capacity (25 amps per circuit), using ATO type fuses. Can be positioned in any convenient protected location with integral mounting bracket.HD-ARM-5

HD-ARM-9Heavy duty armrest with moldedpoly pad, and multi-position 5” or9” adjustable pole. Armrest flipsup for access to equipment andslides forward or back for correctpad positioning.Requires base plate.

Console Accessories

CC12-CFPCC12-FP

12 position ATO fusepanel. The panelcomes with nine

20 amp and three 30 amp capacity fuse holders.

Available with or without cover.

SCN-SPTSide mount adjustable screensupport for laptops.

Both provide ideal screensupport for rugged driving conditions.

SCN-SPT2Bottom mountadjustablescreen supportfor laptops.

ARMP

CHB2MK2-CL

CC12-FP

TRI-LITER

CHB-2

CHB-1

SPM-1CHB-2EN

K-30

LF12-TRB

CC12-CFP

CC12-FP

SWA-HD-TS1Heavy duty swing arm with 1.25”tilt/swivel for mounting keyboardsand computers allows controlledmotion at both ends of the arm.available in 6, 8 and 12” lengths.Accepts all motion attachments

Console Accessories

CLPBDClipboard Holder9.5” W x 2.5” D

NTEPDNotepad Holder7.5” W x 2.5” D

LF-BKTLittleLite Side

Mounting Bracket.

A-BASEAdjustable consoleriser allows 900 series13” Consoles to beraised in severalincrements up to 3”accommodating highervehicle seats or longerequipment. Consolecan be installed level or

on an angle and used with standardmounting kits. Works with allControl-Com accessories.

EXT-BASE Inset: LI-900-00 Console on EXT-BASE

Hinged console riser allows 900 Series 13” Consoles to be raised 5”accommodating higher seats in larger vehicles. Rear hinge and latch designallows easy access to wiring and equipment when the console is raised. Fitsany base plate, flat floor or hump. Works with all Control-Com accessories.

PS2-4 PS2-33 and 4 position power strips feature 15 ampheavy duty receptacles with caps that preventcontamination when not in use.

Osram K-30LittleLite LF12-TRB •LF12-TS-LEDLED and halogen gooseneck lamps provideinterior lighting for reading and reportwriting. Available with dimmer or switch.

LL-BKT2LittleLite Bottom Mounting

Bracket for consoles and docks.

BCR-CLPSpring Steel Bar Code Scanner

Clip with poly sleeves.

CV-RRLA • FE-RRL For relocating factoryAM/FM radios from thedash to the ashtray slotat the bottom of thedash in Crown Victoriaor into the glove box inFord Escape. Frees-up

space for in-dash mounts. Pre-punched for power plugand trunk release. CV-RRLA pictured

SP2-2 SP2-32 and 3 position 15 amp rocker switcheson a 2 inch Control-Com console fill plate.

LF12-TRB

LF12-TS-LED K-30

PB-2500 New Part

Pen Box 2.5" L x 2” D

LSB-400 New Part

Locking Storage Box 4” L x 3.5” D

LSB-600Locking Storage Box 6” L x 5” D

Trunk Mounting SystemsCCV-TRAY-21, 2521” or 25” x 16” powder coated 14 gauge steel equipment tray for Crown Victoriaattaches to pre–drilled holes in the trunk. Tray glides on wear-resistant UHMWpolyethylene and features a snap pin with lanyard to lock the tray in place. Trays areavailable in 21” which extends to the trunk well and 25”, both are interchangeable. Heavy duty frame construction assures long life and a stable equipment platform.

UNI-TRAY-21, 25 Universal 21” or 25” x 16” slide out trunk tray for 2006 Impala and many othervehicles with rear deck mounting space available.

CCV-PAN-24-14Additional 24” x 14” shelf and bracket kit attaches to CCV-TRAY-25. Top tray is adjustable from 3” - 5” in height to allow for variations in equipment.

CCV-SHELF 1•2IMP-SHELFPowder coated steel shelf for the Crown Victoria (24”x14”) orImpala (24”x 30”) attaches topre–drilled holes in the trunk.Tray glides on extendible ballbearing slides and features a

snap pin with lanyard for safety. Available in one andtwo shelf units depending on vehicle.

RHT-342034” x 23” hingedequipment mounting tray for the ChevroletImpala is constructed of14 gauge steel with

welded corner seams for strength, and powder coated for long lifeand easy cleaning. The bale bracket mount system permits easyinstallation and adjustment of the tray height from 6” to 11”.Loosen a wing nut on each side and the tray drops down for easyaccess to your equipment.

ST-1718-DC11 for 2011 ChargerST-1516-DC for 2006 - 10 ChargerST-1516-IM6 for 2006 and newer ImpalaST-1516C for Crown VictoriaST-1516I for Impala 2005 and older15” x 16” Side Hinged Mounting Tray for the Impala and Crown Victoria. The solution for small equipment mounting is Lund’sside mounting tray which allows complete access to the trunk. The tray is made from 1/8” aluminum for strength and mounts ineither the right or left quarter panel area in front of the taillight assembly. The unit is designed for quick and easy installation witha special no hole top bracket. When the tray is secured, it fits in an area not normally “equipment friendly”.

CCV-TRAY2Adjustable double 21” x 16” powder coated steel equipment trayfor Crown Victoria attaches to pre–drilled holes in the trunk.Trays glide on wear-resistant UHMW polyethylene and featuresnap pins with lanyard to lock the tray in place. Top tray frameheight is adjustable, allowing for variations in equipment size.Heavy duty frame construction assures long life and a stableequipment platform.

Printer Mounting Systems

PPJ-CASEDesigned for Pentax PocketJet mobile printers, it utilizes rollor cut-sheet paper depending on user preference. Roll paperis protected from prolonged exposure to direct sunlight. The“Fast Release” design allows rapid docking and un-dockingof the printer for use outside the vehicle. This compact casemay be mounted inside the glovebox of many vehicles or used inpedestal or console configurations.

PPJ-CASE-APSame as above with armrest pad.

PRBKT-EP590Designed to securely mountEpson 590 printers vertically orhorizontally in your vehicle, itfeatures a bale bracket to holdprinter in place, and an adjustablepaper guide with form feeder.Mounts to any motionattachment or assembly.

PPJ-HDARM-WFArmrest mount for Pentax PocketJet printer on a 5”- 8” adjustablewide flange pole mounts directly to base plate. Pull-pin latchingcover lifts for easy printer and paper access plus paper rollerallows simple lift out paper changing. Molded poly armrest padflips up for easy access to equipment. Constructed of 14 ga.powder coated steel. Dimensions: 10.5” L x 6.0” W x 4.25” H

PPJ-HDARM-VPSame as above with a 5”- 8” adjustable vertical pole whichmounts directly to rear of console or vertical surface.

PRBKT-RW420Printer bracket securely mounts the Zebra RW-420 mobileprinter in your vehicle. Locking quick-release springmechanism mounts to any Lund motion attachment orassembly. Vinyl bumpers protect printer. Compact designprovides access to charging port and weighs only 1.5 lbs.Made of black powder coated 14 ga. steel.Dimensions: 7.0” L x 6.0” W x 2.375” H

PRBKT-I70Cannon I70 / I80 printer mount.Printer mount can be used withor without an optional batterypack. Black powder coatedsteel construction weighs only 2.14 lbs.Dimensions: 12.25” L x 7” to 8.78” W x .25” H

PRIF-BRKTPrinter mount interface bracket to TS-60 or motion attachment.

PRBKT-HP460PRBKT-HP450HP printer mounts for modelHP460 / HP450. Printermount can be mounted toany Lund motion attachment with PRIF-BRKT interface bracket. Light weight powder coated steel construction only 2.0 lbs.Dimensions: 14.75” L x 7.25” W x 3.62” H

PPJ-HDARM-WF

PPJ-CASE

PPJ-HDARM-VP

PPJ-CASE-AP

Mounting Solutions Designedand Manufactured by:

Lund Industries, Inc. specializes in understanding vehicleequipment requirements and solutions for over 28 years. Lundprovides your agency with informed solutions that are testedand proven; saving you time and money, while providingefficient, trouble free service from your vehicle equipment.

CV-PPJ-GBDesigned to securely mount thePentax PocketJet mobile printer inthe Ford Crown Victoria glove box.The 16” articulating arm allows theprinter to pull out for easy accessand to be folded and stored withinthe closed glove box.