1

LTE Smart Dashboard Camera System

Quick Start Guide

Model: UCM3310S

2

What’s Included: 1× Alleswolke Smart LTE Hub 1× Alleswolke Smart Dashboard Camera 1× Alleswolke Smart OBD-II Power/Data Cable 1× Camera USB Type-C Power Cable 1× Emergency Button with Strap 1× Camera Dashboard/Windshield Mount 1× Windshield Clean Wiper 1× Hook-and-Loop Fastener 1× Spare Mounting Sticker 10× Cable/Wire Clips 1× Quick Start Guide

3

Get The App Download the free Alleswolke LTEdashcam Smartphone application to start.

You may scan the QR-code and download the smartphone applications via our download guiding web page. Please follow the app’s guide to sign-up and log-in to the app.

4

SIM Card The SIM card has been already installed into your device. In any circumstance that you wish to check or install a new card yourself, push the SIM card to lock/unlock, make sure that the chip side faces down and the odd corner faces outward.

5

Mount Your System Install camera onto the camera mount, peel the protection cover from the sticker on the mount, and press the mount firmly onto the desired place of windshield or the top center of dashboard. The default lens position is facing toward to the windshield for capturing road picture during driving. Install near the driver’s sight of rear view mirror in order to avoid the obstruction of camera’s lens visual coverage when it rotates toward the inside.

6

Connect Cables

1. Connect the USB-C

Cable between Hub and Camera.

2. Connect the OBD-II

Power/Data Cable on the Hub’s side (Micro-USB).

3. Insert Micro SD card

into the camera.* *Micro SD card is not included and needs to be purchased separately. Requires Class 10. Supports up to 64GB or 128GB in FAT32 Format.

7

Connect Cables (cont.)

Hub

USB Type-C Cable

Micro USB to OBD-II Cable

OBD-II Port

Camera

Wire Connection Diagram

Camera’s USB Type-C port

8

Insert Cable to OBD-II Port The OBD-II* port of vehicles is usually located underneath of the dashboard, please check the manual of your vehicle or consult auto specialists to locate it in your vehicle.

*Smart OBD-II Power/Data Cable supports 9V-36V input and is compatible with all regular light vehicles and heavy duty commercial vehicles sold in the United States after January 1, 1996 with OBD-II port equipped.

9

Mount And Turn On The Hub

Wire clips x10

Use the Hook-and-Loop fastener to mount the hub onto the top of the dashboard. Make sure that the car ignition is turned on, and then press the power switch. Use adhesive wire clips to keep your windshield and dashboard clean and organized. Peel the protection cover from the sticker and press the clip firmly onto the desired place of windshield or dashboard.

10

System Status LED After turning on the hub, you will hear a prompt sound from camera to indicate that the system is starting. The signal LED indicator on the hub will blink for a few seconds and stay solid. If the LEDs keep blinking, please check the LED status chart below to identify the problem or contact our support.

Power LED indicator Signal LED indicator

Normal Running status, LEDs stay solid

Signal LEDs will blink for a few seconds to finish system boot up and then flash in sequential-loop order to finish LTE network connection.

Warning: When the system is booted up for the first time, it may take a longer time for the backend of cellular network to finish the registration process. Please re-power cycle the Hub to minimize the waiting time.

11

LED Status Chart

12

Install Emergency Button

Install the Emergency Button with the Self-Grip Strap by tying the panic button around the steering wheel firmly, or anywhere else that is firm and convenient to reach. You can also use the spare double-side sticker to mount the button on the dashboard. When the engine is on, pressing the button shortly* will trigger an emergency event. Long-pressing* the button will switch the system into Patrol Mode.

*See user manual for details

13

Activate a System

Log in the app Tap “add camera” Scan the QR-code on Camera

14

You Are Done!

Congratulations! The system has been set up and ready to go. To view the full user manual, watch useful tutorial videos, find troubleshooting tips, or get support, please visit alleswolke.com/dashcam_support.html

15

Support Page

For product FAQ, troubleshooting, user manual, feature introduction, application notes and overall support, please visit alleswolke.com/dashcam_support.html or scan the QR-code. For watching the installation video and other introduction tutorial video clips, please visit alleswolke.com/dashcam_videos.html or scan the QR-code. To contact our support team, please visit alleswolke.com/customersupport.html or scan the QR-code. To log into the web-portal, Please visit myalleswolke.com

Support/Documents

Installation Video

Contact Us

16

©2018 alleswolke Inc. “alleswolke” logo is trademark of alleswolke inc. App Store is a service mark of Apple inc., Registered in the U.S. and other countries, Google Play and the Google Play logo are trademark of Google inc. 3M is a trademark and company name of the 3M company or the Minnesota Mining and Manufacturing Company.

Compliance and FCC document For Compliance, FCC document and other regulatory information, please visit alleswolke.com/compliance.html About alleswolke inc. For company information including company business address and contact information, please visit alleswolke.com

Product designed in California, USA Assembled in China www.alleswolke.com

October 2018 QSG v1.08