Loxone Electronics GmbHSmart Home 14154 KollerschlagAustria

loxone.com

Need Help?loxone.com/support

Part No: 100043

Dimmer Extension 120V

V16

0420

Technical Specifications

Power supply 18 ... 28VDC

Power consumption typ. 330mW, max. 360mW

Outputs 4 dimmable outputs (trailing / leading edge)power supply: 110 ... 125VAC

AQ1, AQ2, AQ3, AQ4 (per channel)resistive load: 0 ... 200Wcapacitive load: 0 ... 100VAinductive load: 50 ... 200VA

Ambient temperature -10 ... 50°C / 14 ... 122°F

Humidity max. 95% r.H. (non condensing)

Safety rating IP20

Rated impulse voltagefor dimmer outputs

2.5kV (UL60730-1, max. Altitude 2000m)

Operation Type 1 (UL60730-1, CSA E60730-1)

Inputs 8 digital inputs:logic 0: 0 ... 4.5VDCundefined: 4.5 ... 5VDC logic 1: 5 ... 24VDC(Ri=100kOhm)

Interfaces Loxone Link:connection with Miniserver

Degree of pollution 2

Power loss at max. load 1.56W

About the productThe Dimmer Extension 120V is a device for the automatic control and management of home automation and similar non safety critical applications.

Installation & electrical connectionThe installation of the devices is to be mounted on a DIN rail in an electrical distribution housing (Standard distribution) and may only be performed by qualified personnel.

Protection against electrical contact and fire protection must be provided in the final installation by the use of a standards compliant/approved housing. To turn the unit on/off during installation and in case of failure, a separator (disconnecting device) must be present. These must be easily accessible and visible. If the unit is used in a non conform manner as specified by the manufacturer the product included safeguards will be impaired.

1. If multiple Dimmer Extensions are fitted above each other aminimum distance of 50mm between rows has to be main-tained.

2. For better heat dissipation multiple Dimmer Extensionsshould be mounted next to each other rather than aboveeach other.

3. The air flow around the Dimmer Extension should not beobstructed.

4. The ventilation slots have to be kept clear.5. No other sources of heat ought to be mounted below the

Dimmer Extension.

For additional information, declaration of confirmity, visit www.loxone.com/help/dimmer L3L2L1

max. 200VA

max. 200VA

max. 200VA

max. 200VA

Spread loadover L1-L3

N

AQ1

Dim

mer

Oup

uts AQ2

AQ3

AQ4

I1

I2

I3

I4

I5

I6

I7

I8

This folder is a part of the product!

Dig

ital

Inpu

ts

Dim

mer

Outputs

Loxone Link

Power

Supply

LNNAQ1LNNAQ2LNNAQ3LNNAQ4

+24V+24V GNDGNDBUWH

+24 out I1I2I3

I4 I5 I6 I7 I8

GND

Dim

mer Extension

Connection

Wire cross-section 0.05 ... 2.5mm² / AWG30 ... 12

Stripping length 6 ... 7.5mm / 0.24 ... 0.30”

Torque of terminal blocks 0.5 ... 0.6Nm / 0.37 ... 0.44 lbf ft

Temperature resistance min. 80°C / 176°F for IEC, min. 75°C / 167°F for UL

Maintenance & Cleaning This device is free of maintenance and may only be cleaned with a dry cloth.

Dimensions 157x88x57mm / 6.18x3.46x2.24” (LxWxH)