Upload
others
View
31
Download
0
Embed Size (px)
Citation preview
Listing Constructional Data Report (CDR)
Report Number HZ12070036-001 Original Issued: 20-Jul-2012 Revised: None
Standard(s)
Applicant Manufacturer
Address Address
Country CountryContact ContactPhone PhoneFAX FAXEmail Email [email protected]@euronb.com
No.5 Wan gong chi Road,Xiao dongIndustrial Zone, Yuyao City, Ningbo,Zhejiang
0574-62502598 0574-62502598
No.5 Wan gong chi Road,Xiao dongIndustrial Zone, Yuyao City, Ningbo,Zhejiang
China
Ningbo Euro Electrical Co.,Ltd.
1.0 Reference and Address
Ningbo Euro Electrical Co.,Ltd.
0574-62502596
Richard Gan Richard GanChina
0574-62502596
Portable Electric Luminaires – ANSI/UL 153(12th Ed, rev. March 24, 2011)Portable Luminaires – CSA C22.2 No.12-1982 (R2008)
Page 1 of 27
Report No. HZ12070036-001Ningbo Euro Electrical Co.,Ltd.
Page 2 of 27 Issued: 20-Jul-2012Revised: None
ProductBrand name
ModelsModel SimilarityRatingsOther Ratings NA
N/AInput: 12-24Vdc, 3,0A; Output: 12VDC, 20W
DescriptionThe product covered by this report is portable luminaire with LED lighting and rechargeablebattery. The battery shall be assembled with product and its charger shall be provided.IN2400L
2.0 Product Description
Luminaire, PortableSmith Light
ED 16.3.15 (8-Jan-10) Mandatory
Report No. HZ12070036-001Ningbo Euro Electrical Co.,Ltd.
Page 3 of 27 Issued: 20-Jul-2012Revised: None
Photo 1 - Overview
Photo 2 - Overview
3.0 Product Photographs
01
ED 16.3.15 (8-Jan-10) Mandatory
Report No. HZ12070036-001Ningbo Euro Electrical Co.,Ltd.
Page 4 of 27 Issued: 20-Jul-2012Revised: None
3.0 Product Photographs
Photo 3 - Overview
Photo 4 - Overview
01
ED 16.3.15 (8-Jan-10) Mandatory
Report No. HZ12070036-001Ningbo Euro Electrical Co.,Ltd.
Page 5 of 27 Issued: 20-Jul-2012Revised: None
3.0 Product Photographs
Photo 5 - Overview
Photo 6 - Construction
01
01
ED 16.3.15 (8-Jan-10) Mandatory
Report No. HZ12070036-001Ningbo Euro Electrical Co.,Ltd.
Page 6 of 27 Issued: 20-Jul-2012Revised: None
3.0 Product Photographs
Photo 7 - Construction
Photo 8 - Construction
ED 16.3.15 (8-Jan-10) Mandatory
Report No. HZ12070036-001Ningbo Euro Electrical Co.,Ltd.
Page 7 of 27 Issued: 20-Jul-2012Revised: None
3.0 Product Photographs
Photo 9 - Construction
Photo 10 - Construction
01
01
02
02
ED 16.3.15 (8-Jan-10) Mandatory
Report No. HZ12070036-001Ningbo Euro Electrical Co.,Ltd.
Page 8 of 27 Issued: 20-Jul-2012Revised: None
3.0 Product Photographs
Photo 11 - Construction (Battery)
Photo 12 - Construction
01
02
01
ED 16.3.15 (8-Jan-10) Mandatory
Report No. HZ12070036-001Ningbo Euro Electrical Co.,Ltd.
Page 9 of 27 Issued: 20-Jul-2012Revised: None
3.0 Product Photographs
Photo 13 - Construction
Photo 14 - Construction
01
ED 16.3.15 (8-Jan-10) Mandatory
Report No. HZ12070036-001Ningbo Euro Electrical Co.,Ltd.
Page 10 of 27 Issued: 20-Jul-2012Revised: None
3.0 Product Photographs
Photo 15 - Construction (LED control circuit)
Photo 16 - Construction (LED control circuit)
01
02
01
ED 16.3.15 (8-Jan-10) Mandatory
Report No. HZ12070036-001Ningbo Euro Electrical Co.,Ltd.
Page 11 of 27 Issued: 20-Jul-2012Revised: None
3.0 Product Photographs
Photo 17 - Construction
Photo 18 - Construction
01
ED 16.3.15 (8-Jan-10) Mandatory
Report No. HZ12070036-001Ningbo Euro Electrical Co.,Ltd.
Page 12 of 27 Issued: 20-Jul-2012Revised: None
3.0 Product Photographs
Photo 19 - Construction
Photo 20 - Battery charger
01
02
01
ED 16.3.15 (8-Jan-10) Mandatory
Report No. HZ12070036-001Ningbo Euro Electrical Co.,Ltd.
Page 13 of 27 Issued: 20-Jul-2012Revised: None
Photo #
Item
no.1Name
Manufacturer/
trademark2 Type / model2Technical data and securementmeans
Mark(s) of
conformity3
1 1 EnclosureCHI MEICORPORATION
PA-757(+)ABS, yellow, 80°C, minimum4,0mm thick (UL/E56070)
cURus
5 1 Intenal enclosureCHI MEICORPORATION
PA-757(+)ABS, yellow, 80°C, minimum4,0mm thick (UL/E56070)
cURus
3 1Transparentlampshade
CHI MEICORPORATION
PC-110(+)PC, V-2, 105°C, minimum 1,5mmthick (UL/E56070)
cURus
6 1Flexible cablebetween controlgear and battery
YUYAO XUANHUIELECTRIC COLTD
SJT300V, 105°C, 18AWG, with screwgland (UL/E322683)
cULus
14 1Internal wirebetween LED andcontrol circuit
YUYAO RIYUEWIRE & CABLEINDUSTRY COLTD
1015600V, 80°C, 22AWG, Soldering(UL/E256446)
cULus
9 1Internal wirebetween batteryand charger
YUYAO RIYUEWIRE & CABLEINDUSTRY COLTD
1015600V, 80°C, 22AWG, Soldering(UL/E256446)
cULus
12 1 ButtonDAILYWELLELECTRONICSCO LTD
Q13120 V, 5A, 60°C(UL/E187490)
cURus
12 2 SwitchLIGHT COUNTRYCO LTD
R19A-0125 V, 2A, 65°C(UL/E104190)
cURus
19 1 Reflect boardCHI MEICORPORATION
PA-757(+)ABS, yellow, 80°C, minimum1,5mm thick (UL/E56070)
cURus
19 2 PCB for LED array
HESHAN DONGLIELECTRONICTECHNOLOGIESCO LTD
EPAV-0, 180°C, minimum 1,5mm thick(UL/E318223)
cURus
18 1Transparent coverfor encasing heatsink
CHI MEICORPORATION
PC-110(+)PC, V-2, 105°C, minimum 1,5mmthick (UL/E56070)
cURus
15 1 ConnectorFUJIAN SHANYASWITCH CO LTD
FSE1011V-0, 105°C, WireRange:12-28 AWG (UL/E305884)
cURus
15 2 TerminalCIXI KEFAELECTRONICSCO LTD
KF126 (3)250V, 8A, WireRange:14-26 AWG (UL/E306245)
cURus
16 1PCB for controlcircuit
KINGBOARDLAMINATESHOLDINGS LTD
KB-2150GV-0, 105°C, minimum 1,8mm thick(UL/E123995)
cURus
10 2Heat shrinkabletube
SHENZHENWOER HEAT-SHRINKABLEMATERIAL COLTD
RSFR-H 600V, 125°C (UL/E203950) cURus
10 1 Fuse
SHENZHENLANSONELECTRONICSCO LTD
5D 125V, 5A (UL/E221465) cURus
9 2
11 1
20 1 ChargerFUYUANELECTRONIC COLTD
FY1503000Input:100-240V~, 50/60Hz, 80VAoutput:15Vdc, 3A (UL/E304160)
cURus
4.0 Critical Components
Battery
SHANGHAIHONGBEIPOWER SYSTEMCO LTD
FM/BB127,FM/BB1210,FM/BB1218
12V7AH, 12V10AH, 12V18AH(UL/MH46345)
cURus
ED 16.3.15 (8-Jan-10) Mandatory
Report No. HZ12070036-001Ningbo Euro Electrical Co.,Ltd.
Page 14 of 27 Issued: 20-Jul-2012Revised: None
Photo #
Item
no.1Name
Manufacturer/
trademark2 Type / model2Technical data and securementmeans
Mark(s) of
conformity3
4.0 Critical Components
3) Indicates specific marks to be verified, which assures the agreed level of surveillance for the component. "NR" - indicates Unlisted andonly visual examination is necessary. "See 5.0" indicates Unlisted components or assemblies to be evaluated periodically refer to section5.0 for details.
NOTES:
1) Not all item numbers are indicated (called out) in the photos, as their location is obvious.
2) “Various“ means any type, from any manufacturer that complies with the "Technical data and securement means" and meets the "Mark(s)of conformity" can be used.
ED 16.3.15 (8-Jan-10) Mandatory
Report No. HZ12070036-001Ningbo Euro Electrical Co.,Ltd.
Page 15 of 27 Issued: 20-Jul-2012Revised: None
No Unlisted CEC components are used in this report.
5.0 Critical Unlisted CEC Components
ED 16.3.15 (8-Jan-10) Mandatory
Report No. HZ12070036-001Ningbo Euro Electrical Co.,Ltd.
Page 16 of 27 Issued: 20-Jul-2012Revised: None
2. Mechanical Assembly - Components such as switches, fuseholders, connectors, wiring terminals and displaylamps are mounted and prevented from shifting or rotating by the use of lockwashers, starwashers, or othermounting format that prevents turning of the component.
3. Corrosion Protection - All ferrous metal parts are protected against corrosion by painting, plating or theequivalent.
4. Accessibility of Live Parts - All uninsulated live parts in primary circuitry are housed within a non-metallicenclosure constructed with no openings other than those specifically described in Sections 4 and 5.
5. Grounding - None6. Polarized Connection - None7. Internal Wiring - Internal wiring is routed away from sharp or moving parts. Internal wiring leads terminating
in soldered connections are made mechanically secure prior to soldering. Recognized Componentseparable (quick disconnect) connectors of the positive detent type, closed loop connectors, or other typesspecifically described in the text of this report are also acceptable as internal wiring terminals. At pointswhere internal wiring passes through metal walls or partitions, the wiring insulation is protected againstabrasion or damage by plastic bushings or grommets. All wiring is minimum 22AWG with a minimum ratingof 600V, 80°C.
8. Schematics - Refer to Illustration 1 for schematics requiring verification during Field RepresentativeInspection Audits.
9. Markings - The product is marked on as labeling system as described of Section as follows: <manufacturer'sname, brand name, model number, date of manufacturer, electrical ratings>.
10. Cautionary Markings -The following are required: refer to Illustration 2 - Label for details11. Installation, Operating and Safety Instructions - Instructions for installation and use of this product are
provided by the manufacturer. Refer to Illustration 3- Instruction for details.
1. Spacing - In primary circuits, 6,4 mm minimum spacing are maintained through air and over surfaces ofinsulating material between current-carrying parts of opposite polarity and 9,5mm minimum between suchcurrent-carrying parts and dead-metal parts or low voltage isolated circuits.
Listed Component - A component part, which has been previously Listed or Certified by an accreditedCertification Organization with no restrictions and is used in the intended application within its ratings.
Critical Features/Components - An essential part, material, subassembly, system, software, or accessory of aproduct that has a direct bearing on the product’s conformance to applicable requirements of the productstandard.Construction Details - For specific construction details, reference should be made to the photographs anddescriptions. All dimensions are approximate unless specified as exact or within a tolerance. In addition to thespecific construction details described in this Report, the following general requirements also apply.
Recognized Component - A component part, which has been previously evaluated by an accredited certificationbody with restrictions and must be evaluated as part of the basic product considering the restrictions as specifiedby the Conditions of Acceptability.
6.0 Critical Features
Unlisted Component - A part that has not been previously evaluated to the appropriate designated componentstandard. It may also be a Listed or Recognized component that is being used outside of its evaluated Listing orcomponent recognition.
ED 16.3.15 (8-Jan-10) Mandatory
Report No. HZ12070036-001Ningbo Euro Electrical Co.,Ltd.
Page 17 of 27 Issued: 20-Jul-2012Revised: None
Illustration 1 - LED control circuit
7.0 Illustrations
ED 16.3.15 (8-Jan-10) Mandatory
Report No. HZ12070036-001Ningbo Euro Electrical Co.,Ltd.
Page 18 of 27 Issued: 20-Jul-2012Revised: None
7.0 Illustrations
ED 16.3.15 (8-Jan-10) Mandatory
Report No. HZ12070036-001Ningbo Euro Electrical Co.,Ltd.
Page 19 of 27 Issued: 20-Jul-2012Revised: None
7.0 Illustrations
Illustration 2 - Label
Model:IN2400L
Lamp rating:Input :12-24VDC, 3,0AOutput: 12VDC, 20WDate:
Ningbo Euro Electrical Co.,LtdNo.5 Wan gong chi Road,Xiao dong Industrial Zone, Yuyao City, Ningbo, Zhejiang, China
CONFORMS TO ANSI/UL STD 153CERTIFIED TO CSA STD C22.2 No.12
4005288
WARNING:--"RISK OF ELECTRIC SHOCK" or "RISQUE DE CHOC ÉLECTRIQUE"--"CAUTION – RISK OF FIRE" or "ATTENTION – RISQUE D’INCENDIE"--"DISCONNECT POWER BEFORE SERVICING" or "COUPER L’ALIMENTATION AVANT L’ENTRETIEN"
ED 16.3.15 (8-Jan-10) Mandatory
Report No. HZ12070036-001Ningbo Euro Electrical Co.,Ltd.
Page 20 of 27 Issued: 20-Jul-2012Revised: None
7.0 Illustrations
Illustration 3- Instruction
ED 16.3.15 (8-Jan-10) Mandatory
Report No. HZ12070036-001Ningbo Euro Electrical Co.,Ltd.
Page 21 of 27 Issued: 20-Jul-2012Revised: None
7.0 Illustrations
Contact DetailsNingbo Euro Electrical Co.,Ltd.No.5 Wan gong chi Road,Xiao dong Industrial Zone, Yuyao City, Ningbo, Zhejiang, China
ED 16.3.15 (8-Jan-10) Mandatory
Report No. HZ12070036-001Ningbo Euro Electrical Co.,Ltd.
Page 22 of 27 Issued: 20-Jul-2012Revised: None
7.0 Illustrations
ED 16.3.15 (8-Jan-10) Mandatory
Report No. HZ12070036-001Ningbo Euro Electrical Co.,Ltd.
Page 24 of 27 Issued: 20-Jul-2012Revised: None
BASIC LISTEEAddressCountryProduct
MULTIPLE LISTEE 1AddressCountry
Brand Name
ASSOCIATEDMANUFACTURER
AddressCountry
BASIC LISTEE MODELS
MULTIPLE LISTEE 2AddressCountry
Brand Name
ASSOCIATEDMANUFACTURER
AddressCountry
BASIC LISTEE MODELS
MULTIPLE LISTEE 3AddressCountry
Brand Name
ASSOCIATEDMANUFACTURER
AddressCountry
BASIC LISTEE MODELS
None
None
None
MULTIPLE LISTEE 1 MODELS
MULTIPLE LISTEE 3 MODELS
MULTIPLE LISTEE 2 MODELS
Luminaire, PortableChina
9.0 Correlation Page For Multiple ListingsThe following products, which are identical to those identified in this report except for model number and Listeename, are authorized to bear the ETL label under provisions of the Intertek Multiple Listing Program.
Ningbo Euro Electrical Co.,Ltd.No.5 Wan gong chi Road,Xiao dong Industrial Zone, Yuyao City, Ningbo, Zhejiang
ED 16.3.15 (8-Jan-10) Mandatory
Report No. HZ12070036-001Ningbo Euro Electrical Co.,Ltd.
Page 25 of 27 Issued: 20-Jul-2012Revised: None
10.0 General InformationThe Applicant and Manufacturer have agreed to produce, test and label ETL Listed products in accordance withthe requirements of this Report. The Manufacturer has also agreed to notify Intertek and to request authorizationprior to using alternate parts, components or materials.
COMPONENTSComponents used shall be those itemized in this Intertek report covering the product, including any amendments
LISTING MARKThe ETL Listing mark applied to the products shall either be separable in form, such as labels purchased fromIntertek, or on a product nameplate or other media only as specifically authorized by Intertek. Use of the mark is
MANUFACTURING AND PRODUCTION TESTSManufacturing and Production Tests shall be performed as required in this Report.
FOLLOW-UP SERVICEPeriodic unannounced audits of the manufacturing facility (and any locations authorized to apply the mark) shallbe scheduled by Intertek. An audit report shall be issued after each visit. Special attention will be given to thefollowing:
1. Conformance of the manufactured product to the descriptions in this Report.2. Conformance of the use of the ETL mark with the requirements of this Report and the Certification Agreement.3. Manufacturing changes.4. Performance of specified Manufacturing and Production Tests.
In the event that the Intertek representative identifies non-conformance(s) to any provision of this Report, theApplicant shall take one or more of the following actions:
1. Correct the non-conformance.2. Remove the ETL Mark from non-conforming product.3. Contact the issuing product safety evaluation center for instructions.
10.1 Evaluation of Unlisted Components
Note to Intertek Follow Up Inspector: The Component Evaluation Center, CEC, will notify you in writingwhen these components must be selected and sent to the CEC for re-evaluation
Ship the samples to:Intertek Testing Services Shanghai LimitedETL Component Evaluation CenterBuilding No. 86, 1198 Qinzhou Road (North)Shanghai 200233, ChinaAttn: Ms. Dansy XuSample Disposition: Due to the destructive nature of the testing, all samples will bediscarded at the conclusion of testing unless, the manufacturer specifically requests thereturn of the samples. The request for return must accompany the initial componentshipment.
Because Unlisted Components are uncontrolled, and they do not fall under a third party follow up program,Intertek may require these components to be tested and/or evaluated at least once annually, more often forcertain components, as part of the independent certification process. The Unlisted Components in Section 5.0require testing and/or evaluation as indicated.
ED 16.3.15 (8-Jan-10) Mandatory
Report No. HZ12070036-001Ningbo Euro Electrical Co.,Ltd.
Page 26 of 27 Issued: 20-Jul-2012Revised: None
Product Test Voltage Test TimeAll products covered by this Report. 1000V 60 s
or1200V 1 s
Test Equipment
The test equipment shall incorporate a transformer with an essentially sinusoidal output, a means to indicate theapplied test potential, and an audible and/or visual indicator of dielectric breakdown.
Method
The test voltage specified below shall be applied between primary circuits and accessible dead-metal parts. Thetest voltage may be gradually increased to the specified value but must be maintained at the specified value forone second or one minute as required.
One hundred percent of production of the products covered by this Report shall be subjected to a routineproduction line dielectric withstand test.
The test shall be conducted on products, which are fully assembled. Prior to applying the test potential, allswitches, contactors, relays, etc., should be closed so that all primary circuits are energized by the test potential.If all primary circuits cannot be tested at one time, then separate applications of the test potential shall be made.
If the rated output of the test equipment is 500VA or more, the applied test potential may be indicated by either:1 - a voltmeter in the primary circuit;2 - a selector switch marked to indicate the test potential; or3 - a marking in a readily visible location to indicate the test potential for test equipment having a single testpotential output.In cases 2 and 3, the test equipment shall include a lamp or other visual means to indicate that the test potentialis present at the test equipment output. All test equipment shall be maintained in current calibration.
Products Requiring Dielectric Voltage Withstand Test:
The test equipment shall incorporate a voltmeter in the output circuit to indicate directly the applied test potentialif the rated output of the test equipment is less than 500VA.
Dielectric Voltage Withstand Test
11.1 Dielectric Voltage Withstand Test
11.0 Manufacturing and Production TestsThe manufacturer agrees to conduct the following Manufacturing and Production Tests as specified:
Required Tests
ED 16.3.15 (8-Jan-10) Mandatory
Report No. HZ12070036-001Ningbo Euro Electrical Co.,Ltd.
Page 27 of 27 Issued: 20-Jul-2012Revised: None
Date/ Project Handler/Proj # Site ID Reviewer
None
12.0 Revision SummaryThe following changes are in compliance with the declaration of Section 8.1:
Section Item Description of Change
ED 16.3.15 (8-Jan-10) Mandatory