Listing Constructional Data Report (CDR) · ELECTRICAL APPLIANCE CO LTD (E249977) S-A AC 125V, 16A, 50000 cycles, T250, The operating temperature is 190ºC, secured to cooking plate

Listing Constructional Data Report (CDR)

Report Number 130502119SHA-001 Original Issued: 5-Jul-2013 Revised: 4-May-2018

Standard(s)

Applicant Manufacturer

Address Address

Country CountryContact ContactPhone PhoneFAX FAXEmail Email

P.R.China

[email protected]

Zhenxi Village, Langxia Street, Yuyao, Ningbo

[email protected]

86-574-62288062


Mr. Jiang Binhua

86-574-62263280

P.R.China

86-574-62288062

1.0 Reference and Address

Ningbo Golden Age Electric Co., Ltd.

Household Electric Skillets And Frying-Type Appliances [UL 1083:2009 Ed.6+R:15Jul2016]


Mr. Jiang Binhua

Page 1 of 25

Report No. 130502119SHA-001Ningbo Golden Age Electric Co., Ltd.

Page 2 of 25 Issued: 5-Jul-2013Revised: 4-May-2018

Product

Brand name

Models

Model Similarity

Ratings

Other Ratings

2.0 Product Description

Grill

NA

NA

None

120V~, 60Hz, 1400W

DescriptionThe product covered by this report is household, indoor use, cord connected grill. It incorporates thermostat and thermal cut off to safeguard.

GH-815

ED 16.3.15 (20-Apr-17) Mandatory



Photo 1 - Over view

Photo 2 - Over view

3.0 Product Photographs

1

2

3

4

5

6

7

8

9





Photo 3 - Heating plate view

Photo 4 - Bottom view

10

11





Photo 5 - Terminal box view

Photo 6 - Internal of top side view

12

13

14

15





Photo 7 - Internal of top side view

Photo 8 - Internal of bottom side view

19

16

17

18

20

21

22




Photo #

Item

no.1 NameManufacturer/

trademark2 Type / model2Technical data and securement means

Mark(s) of conformity

3

1 1Plastic handle support

SHAXIAN HONGSHENG PLASTIC CO LTD (E206745)

HG-6062J

PF, Rated V-0, HWI=0, HAI=1, RTI(150,150,150), min. thickness 1.5mm, Secured on heating plate by screws.

URus

1 2 Control panel


HG-6062J

PF. Rated V-0, HWI=0, HAI=1, RTI(150,150,150), min. thickness 1.5mm, Fixed to metal enclosure by screws.

URus


Stainless steel Minimum thickness: 0.3mm NR


Iron Minimum thickness: 0.4mm NR

1 4 Plug Various VariousNEMA 1-15P, rated:125V, 15A, connected with 16AWG flexible cord.

UL or ETL

1 5 Power cord Various HPN16AWGx2C, 105°C, 0.6-2.1m length.

UL or ETL

2 6 KnobE I DUPONT DE NEMOURS & CO INC (E41938)

70G13HS1L

PA66, Rated HB, HWI=4, HAI=0, RTI(140,125,140), min. thickness 1.5mm, all color, snapped to thermostat shaft.

URus

SABIC JAPAN L L C (E207780)

2200

PEI, Rated V-0, HWI=2, HAI=3, RTI(170,170,170), min. thickness 0.8mm, all color, Snap-in the top enclosure.

URus

BAYERMATERIALSCIENCE AG (E41613)

2858

PC, Rated V-2, HWI=3, HAI=0, RTI(125,115,125), min. thickness 0.8mm, all color, Snap-in the top enclosure.

URus

2 8 Handle Ningbo Golden Age Electric Co., Ltd.

ADC12 AL, Minimum thickness: 0.7mm NR

2 9 Lock buttonCHI MEICORPORATION (E56070)

PA-706

ABS, Rated HB, HWI=4, HAI=0, RTI(60,60,60), min. thickness 0.6mm, all color, fixed toghter by screws.

URus

3 10 Heating plateNingbo Golden Age Electric Co., Ltd.

ADC12AL, Minimum thickness: 0.8mm, painted with PTFE, fixed to the enclosure by screws.

NR

4 11 Bottom enclosure


HG-6062J

PF, Rated V-0, HWI=0, HAI=1, RTI(150,150,150), min. thickness 1.5mm, Fixed to heating plate by screws.

URus

5 12Terminal box cover

SAMSUNGTOTALPETROCHEMICALS CO LTD (E140331)

FB51

PP, Rated V-2, HWI=2, HAI=0, RTI(130,130,130), min. thickness 1.5mm, all color, Fixed to bottom enclosure by screws.

URus

4.0 Critical Components

Indicator cover72

Metal enclosure31




Photo #

Item




3


5 13 Wire connectorHEAVY POWERCO LTD (E113650)

CE2 300V, 150°C. URus

6 14 Indicator support

SHANDONG JINBAO ELECTRONICS CO LTD (E141940)

ZD-95(G)F1V-0, 130°C, secured on control panel by screw.

URus

6 15Sleeving of internal wire

SHENZHENWAHCHANGWEIINDUSTRIAL COLTD (E233803)

SRS-70Grade A silicone-polymer coatedfiberglass sleeving, 600V, 200°C.Used to cover internal wire.

URus

CIXI SHUANGHONG WIRE CO LTD (E333296)

3122300Vac, 200ºC, 22AWG used for lamp, 18-20AWG for other use, passed VW-1 per UL 1581.

See 5.0

Various 3122300Vac, 200ºC, VW-1, 22AWG used for lamp, 18-20AWG for other use.

URus

SHAOXING XINDA ELECTRONICS CO LTD (E329518)

KST820

AC 125V, 15A, 50000 cycles, T250, The operating temperature is 190ºC, secured to cooking plate by one screw.

URus

ZHEJIANG SKYWELL ELECTRICAL APPLIANCE CO LTD (E249977)

S-A


URus

SHAOXING ZHONGXIN ELECTRIC APPLIANCES CO LTD (E243487)

KST220


URus

HAIYAN DONGHAI ELECTRICAL APPLIANCE CO LTD (E481296)

TYP96A


URus

7 18 Mica

ZHEJIANG RONGTAI ELECTRIC MATERIAL CO LTD (E231452)

R-5660-X94V-0, Min.thickness 0.35mm. Secured on heating plate by screw and metal plate.

URus

Internal wire

Thermostat 177

167




Photo #

Item




3


SIN TIONG WAH ELECTRIC PRODUCTS (SHENZHEN) CO LTD (E146955)

FSG-3A*#Grade A silicone-polymer coated fiberglass sleeving, 600V, 200°C.

URus

SHENZHEN WAHCHANGWEI INDUSTRIAL CO LTD (E233803)

SRS-70Grade A silicone-polymer coated fiberglass sleeving, 600V, 200°C.

URus

NINGBO HOPE WELL INSULATION MATERIAL CO (E238349)

SRG-504Grade A silicone-polymer coated fiberglass sleeving, 600V, 200°C.

URus

AUPO ELECTRONICS LTD (E140847)

BF240+Rated: AC120V, 15A, Tf240°C. Covered by insulation sleeving and secured by a depressor

URus

ZHONGSHAN SHENG PING THERMAL PROTECTORS CO LTD (E225340)

SPF240Rated: AC120V, 15A, Tf240°C. Covered by insulation sleeving and secured by a depressor

URus

NEC SCHOTT COMPONENTS CORP (E71747)

SF240ERated: AC120V, 15A, Tf240°C. Covered by insulation sleeving and secured by a depressor

URus

8 21 Heating elementNingbo Golden Age Electric Co., Ltd.

KTG-11AC 120V, 60Hz, 700W, pressured in the groove of the cooking plate.

See 5.0

8 22 Quick connector

ZHEJIANGYUESHENELECTRON COLTD (E315941)

TJC3-XXYSeries

Used for internal wire to heating element and thermostat. Min. thickness 0.3mm.

URus

HANGZHOU HENGBO LABEL CO LTD (MH26685)

JH-1Max. temp. 80°C, min. temp. –40°C, Adhere to surface of the bottom enclosure.

URus

3M CHINA CO LTD (MH45276)

57830Max. temp.80°C, min. temp. –30°C, Adhere to surface of the bottom enclosure.

URus

8 19Insulation of thermal cut off

NOTES:1) Not all item numbers are indicated (called out) in the photos, as their location is obvious.2) “Various“ means any type, from any manufacturer that complies with the "Technical data and securement means" and meets the "Mark(s) of conformity" can be used.3) Indicates specific marks to be verified, which assures the agreed level of surveillance for the component. "NR" - indicates Unlisted and only visual examination is necessary. "See 5.0" indicates Unlisted components or assemblies to be evaluated periodically refer to section 5.0 for details.

4 23Marking plate (not show)

8 20 Thermal cut off




Photo # Item no.

8 21

-

Frequency: Annual 3

Dimension checking As below drawing

Dielectric StrengthApply voltage Between Test Voltage Test TimeLive parts and sheath 1000V

VERIFICATION PROCESS

Live parts and housing

See resistance per element above.

1200V 1 second

Test Name Test ParametersWinding resistance

Test Site: CEC Number of samples to test:

1 minute

Manufacturer/Trademark Type / model

Dimensions/thickness/assembly information

Insulation class

MATERIALS LIST (refer to the picture below for assembly drawing) Component Manufacturer Type/modelCore material


0Cr25AL5 20.6ΩInsulator MgO thickness: over 1.4mm

Encasement Silicone rubber thickness: over 1.2mm

5.0 Critical Unlisted CEC Components

Component Standard used: UL 1030, Seventh Edition, Rev. Feb. 2, 2010

Heating elementNingbo Golden Age Electric Co., Ltd.

KTG-11

Electrical Rating: 120V, 60Hz, 700W

HEATER ELEMENT Name

Sheath Stainless steel Ø6.6mm, thickness: 0.7mm




5.0 Critical Unlisted CEC Components

Photo # Item no.

7 16

NA

Frequency: Annual 1

MATERIALS LIST

LEAD WIREName Manufacturer/Trademark Type / model

Internal wireCIXI SHUANGHONG WIRE CO LTD (E333296)

3122

Electrical Rating:300Vac, 200ºC, 22AWG used for lamp, 18-20AWG for other use

Insulation class

Component Standard used: UL 1581, refer to VW-1 test report by INTERTEK 140301364SHA-001

VERIFICATION PROCESS

CEC

Component Manufacturer Type/model Length

Lead wireCIXI SHUANGHONG WIRE CO LTD

3122 1.2M for test

Continues to flame time 30 secondsCotton Not be ignited

Number of samples to test:

Test Name Test result Indicator flag Not be ignited

Test Site:




2. Mechanical Assembly - Components such as switches, fuseholders, connectors, wiring terminals and display lamps are mounted and prevented from shifting or rotating by the use of lockwashers, starwashers, or other mounting format that prevents turning of the component.

3. Corrosion Protection - All ferrous metal parts are protected against corrosion by painting, plating or the equivalent.

4. Accessibility of Live Parts - All uninsulated live parts in primary circuitry are housed within a plastic enclosure constructed with no openings other than those specifically described in Sections 4 and 5.

5. Grounding - NA.6. Polarized Connection - This product is provided with a polarized power supply connection. All single pole

switches and thermal cut-out are connected only to the ungrounded supply circuit conductor..7. Internal Wiring - Internal wiring is routed away from sharp or moving parts. Internal wiring leads terminating

in soldered connections are made mechanically secure prior to soldering. Recognized Component separable (quick disconnect) connectors of the positive detent type, closed loop connectors, or other types specifically described in the text of this report are also acceptable as internal wiring terminals. At points where internal wiring passes through metal walls or partitions, the wiring insulation is protected against abrasion or damage by plastic bushings or grommets. All wiring is minimum 22 AWG, with a minimum rating of 300V, 200°C.

8. Schematics - None9. Markings - The product is marked on as labeling system as described in item no. 23 of Section 4.0 and refer

to Illustration 1 for details: manufacturer's name, model number, date of manufacturer, electrical ratings, warning sentences etc.

10. Cautionary Markings - Refer to Illustration No. 1 for details.11. Installation, Operating and Safety Instructions - Instructions for installation and use of this product are

provided by the manufacturer. Refer to Illustration No(s). 2 for details.

Recognized Component - A component part, which has been previously evaluated by an accredited certification body with restrictions and must be evaluated as part of the basic product considering the restrictions as specified by the Conditions of Acceptability.

6.0 Critical Features

Unlisted Component - A part that has not been previously evaluated to the appropriate designated component standard. It may also be a Listed or Recognized component that is being used outside of its evaluated Listing or component recognition.

1. Spacing - In primary circuits, 1.6 mm minimum for USA is maintained through air and over surfaces of insulating material between current-carrying parts of opposite polarity and 1.6 mm minimum between such current-carrying parts and dead-metal parts or low voltage isolated circuits.

Listed Component - A component part, which has been previously Listed or Certified by an accredited Certification Organization with no restrictions and is used in the intended application within its ratings.

Critical Features/Components - An essential part, material, subassembly, system, software, or accessory of a product that has a direct bearing on the product’s conformance to applicable requirements of the product standard.Construction Details - For specific construction details, reference should be made to the photographs and descriptions. All dimensions are approximate unless specified as exact or within a tolerance. In addition to the specific construction details described in this Report, the following general requirements also apply.




Illustration 1 - Marking label

Remark:

7.0 Illustrations

Remark:

1. The precautionary signal word such as “WARNING” shall be in letters not less than 2.4 mm high, if contrasting

color is used, lettering other than signal words can be a minimum of 1.6 mm high.

2. The control number and wording “CONFORMS TO UL STD.1083” and similar shall be at least 1.5 mm high.

3. Note: MM for month, YY for year.

4. Carton marking: "Household use only"5. The ETL logo shall be legible and clear.




7.0 IllustrationsIllustration 2 - Manual instruction

Remark: 1. "IMPORTANT SAFEGUARDS" and "SAVE THESE INSTRUCTIONS" shall be in letters not less

than 4.8mm high.

2. Upper case letters shall not be less than 2.0mm hith, Lower case letters shall not be less than 1.6mm high.




7.0 IllustrationsIllustration 2a - Manual instruction(Continued)




7.0 IllustrationsIllustration 2b - Manual instruction(Continued)




7.0 IllustrationsIllustration 2c - Manual instruction(Continued)




7.0 IllustrationsIllustration 2d - Manual instruction(Continued)




Evaluation Period Project No.130502119SHA-001

Sample Rec. Date 5/29/2013 Condition Prototype Sample ID. 0130529-02-001Test LocationTest Procedure

UL 746C, 6th Edition, Rev. Feb 6, 2013 Clause

----------

------------------315661

----

----

Evaluation Period Project No. 140400768HZH

Sample Rec. Date 4/29/2014 Condition Prototype Sample ID. 1140429-06-006Test LocationTest Procedure

Resistance to impact Test --

Dieletrical Voltage-Withstand Test 10

Power Input Test 9Leakage Current Test 12

Mold-stress relief distortion Test --

Test Description

UL 1030, 7th edition, rev. February 2, 2010

Control Devices Tests 48--Strain Relief Test After Mold Stress-Relief Distortion

37Mechanical Endurance Test 44Stability Test

Strain Relief Test

Metal Enclosure Impact Test Push-Back Relief Test

3635

Abnormal Operation Test 46

Power Input Test 26

Dielectric Voltage-Withstand test 3334

2831

Insulation Resistance and Leakage Current Tests as a Result of Moisture

8.0 Test Summary

2013-05-29 to 2013-06-29

Inetrtek Testing Services Shanghai LimitedTesting Lab

UL 1083, Sixth Edition, Dated June 17, 2011 Clause

16Test Description

32

Determination of the result includes consideration of measurement uncertainty from the test equipment and methods. The product was tested as indicated below with results in conformance to the relevant test criteria.

Thermal cut offs

VW-1 test Section 1080

2014-04-29 to 2014-06-09

Intertek Testing Services Shanghai Ltd.Testing Lab

Refer to test report 140301364SHA-001 by INTERTEK. Determination of the result includes consideration of measurement uncertainty from the test equipment and methods. The product was tested as indicated below with results in conformance to the relevant test criteria.

Test Description UL 1581

Normal Temperature Test

Leakage Current Test 27Operational Tests

The following tests were performed:




8.0 Test SummaryEvaluation Period Project No. 140900183HZHSample Rec. Date NA Condition Prototype Sample ID. NATest LocationTest Procedure

UL 746C, 6thEdition, Rev.August 29, 2013Clause

Evaluation Period Project No. 180401099SHASample Rec. Date NA Condition Prototype Sample ID. NATest LocationTest Procedure

-

Completed by: Reviewed by:Title: Title:

Signature: Signature:

8.1 Signatures A representative sample of the product covered by this report has been evaluated and found to comply with the applicable requirements of the standards indicated in Section 1.0.

Gavin Fu Wayle ChenEngineer Reviewer

Test Description

UL 1083, Sixth Edition, Dated January 9, 2009, Rev. May 29,

2014Clause

2014-09-11 to 2014-10-09

16 No. 1 Ave., Xiasha Economic Development District, Hangzhou 310018, ChinaTesting Lab


None tests need to do.

2018-04-13 to 2018-05-03

Intertek Testing Services Shanghai Ltd.Testing Lab


None tests need to do.

Test DescriptionUL 1083:2009 Ed.6+R:15Jul2016

Clause




BASIC LISTEE

Address

CountryProduct

MULTIPLE LISTEE 1AddressCountry

Brand Name

ASSOCIATED MANUFACTURER

AddressCountry

BASIC LISTEE MODELS


Brand Name


AddressCountry

BASIC LISTEE MODELS


Brand Name


AddressCountry

BASIC LISTEE MODELS

None

None

None

MULTIPLE LISTEE 1 MODELS



GrillP.R.China

9.0 Correlation Page For Multiple ListingsThe following products, which are identical to those identified in this report except for model number and Listee name, are authorized to bear the ETL label under provisions of the Intertek Multiple Listing Program.






10.0 General InformationThe Applicant and Manufacturer have agreed to produce, test and label ETL Listed products in accordance with the requirements of this Report. The Manufacturer has also agreed to notify Intertek and to request authorization prior to using alternate parts, components or materials.

COMPONENTSComponents used shall be those itemized in this Intertek report covering the product, including any amendments and/or revisions.

LISTING MARKThe ETL Listing mark applied to the products shall either be separable in form, such as labels purchased from Intertek, or on a product nameplate or other media only as specifically authorized by Intertek. Use of the mark is subject to the control of Intertek.

The mark must include the following four items:

1) applicable country identifiers "US" and/or "C" or "US", "C" and "EU" 2) the word "Listed" or "Classified" or "Recognized Component" (whichever is appropriate)3) a control number issued by Intertek 4) a product descriptor that identifies the standards used for certification. Example:

For US standards, the words, “Conforms to” shall appear with the standard number along with the word, “Standard” or “Std.” Example: “Conforms to ANSI/UL Std. XX.”

For Canadian standards, the words “Certified to CAN/CSA Standard CXX No. XX.” shall be used, or abbreviated, “Cert. to CAN/CSA Std. CXX No. XX.”

Can be used together when both standards are used.

Note: A facsimile must be submitted to Intertek, Attn: Follow-up Services for approval prior to use. The facsimile need not have a control number. A control number will be issued after signed Certification Agreements have been received by the Follow-up Services office, approval of the facsimile of your proposed Listing Mark, satisfactory completion of the Listing Report, and scheduling of a factory assessment in your facility.MANUFACTURING AND PRODUCTION TESTSManufacturing and Production Tests shall be performed as required in this Report.

FOLLOW UP SERVICEPeriodic unannounced audits of the manufacturing facility (and any locations authorized to apply the mark) shall be scheduled by Intertek. An audit report shall be issued after each visit. Special attention will be given to the following:

1. Conformance of the manufactured product to the descriptions in this Report.2. Conformance of the use of the ETL mark with the requirements of this Report and the Certification 3. Manufacturing changes.4. Performance of specified Manufacturing and Production Tests.

In the event that the Intertek representative identifies non-conformance(s) to any provision of this Report, the Applicant shall take one or more of the following actions:

1. Correct the non-conformance.2. Remove the ETL Mark from non-conforming product.3. Contact the issuing product safety evaluation center for instructions.




10.1 Evaluation of Unlisted Components

Note to Intertek Follow Up Inspector: The Component Evaluation Center, CEC, will notify you in writing when these components must be selected and sent to the CEC for re-evaluation

Ship the samples to:Intertek Testing Services Shanghai LimitedETL Component Evaluation CenterBuilding No. 86, 1198 Qinzhou Road (North)Shanghai 200233, ChinaAttn: Ms. Angela HanSample Disposition: Due to the destructive nature of the testing, all samples will be discarded at the conclusion of testing unless, the manufacturer specifically requests the return of the samples. The request for return must accompany the initial

component shipment.

Because Unlisted Components are uncontrolled, and they do not fall under a third party follow up program, Intertek may require these components to be tested and/or evaluated at least once annually, more often for certain components, as part of the independent certification process. The Unlisted Components in Section 5.0 require testing and/or evaluation as indicated.




Product Test Voltage Test TimeAll products covered by this Report. 1000V 60 s

or1200V 1 s

The test equipment shall incorporate a voltmeter in the output circuit to indicate directly the applied test potential if the rated output of the test equipment is less than 500VA.If the rated output of the test equipment is 500VA or more, the applied test potential may be indicated by either: 1 - a voltmeter in the primary circuit; 2 - a selector switch marked to indicate the test potential; or 3 - a marking in a readily visible location to indicate the test potential for test equipment having a single test potential output. In cases 2 and 3, the test equipment shall include a lamp or other visual means to indicate that the test potential is present at the test equipment output. All test equipment shall be maintained in current calibration.

Products Requiring Dielectric Voltage Withstand Test:

Products Requiring Polarization Test:All products covered by this Report.

11.2 Polarization Test:MethodEach appliance provided with a polarized attachment plug (2-wire plug with one blade wider than another) shallbe tested with a polarized continuity between the grounded supply-circuit conductor of the attachment plug (wideblade of a 2-wire plug) and the part of the appliance that is intended to be connected to the grounded supply-circuit conductor. If the continuity cannot be readily determined by visual inspection and component checking, anelectrical continuity test is to be made.

The test equipment shall incorporate a transformer with an essentially sinusoidal output, a means to indicate the applied test potential, and an audible and/or visual indicator of dielectric breakdown.

Test Equipment

Method

The test voltage specified below shall be applied between primary circuits and accessible dead-metal parts. The test voltage may be gradually increased to the specified value but must be maintained at the specified value for one second or one minute as required.

One hundred percent of production of the products covered by this Report shall be subjected to a routine production line dielectric withstand test.

The test shall be conducted on products, which are fully assembled. Prior to applying the test potential, all switches, contactors, relays, etc., should be closed so that all primary circuits are energized by the test potential. If all primary circuits cannot be tested at one time, then separate applications of the test potential shall be made.

11.1 Dielectric Voltage Withstand Test

11.0 Manufacturing and Production TestsThe manufacturer agrees to conduct the following Manufacturing and Production Tests as specified:

Required TestsDielectric Voltage Withstand TestPolarization Test




Date/ Project Handler/Proj # Site ID Reviewer

10-Jun-2014Gavin Fu/Jackie Zhao

4 16

Specify one manufacturers, revise technical data and describe as unlisted components, Add an alternative "Various" including "300Vac, 200ºC, VW-1, 22AWG used for lamp, 18-20AWG for other use." technical data.

140400768HZH

4 17Add alternative thermostat type KST220 manufactured by SHAOXING ZHONGXIN ELECTRIC APPLIANCES CO LTD.

5 \ Add annual test for above lead wire8 \ Add the test information for lead wire

10-Oct-2014Gavin Fu/Jackie Zhao

1 \Updated the standard to Household Electric Skillets and Frying-Type Appliances - UL 1083, Sixth Edition, Dated January 9, 2009, Rev. May 29, 2014

140900183HZH

8 \ Added the information for changes.

8-Aug-2016Gavin Fu/Wayle Chen

4 4,5 Add the verified mark "ETL" in "Mark(s) of conformity"

160800399SHA

4 17 Add alternative thermostat type TYP96A.

4-May-2018Gavin Fu/Wayle Chen

1 \

Update standard from "Household Electric Skillets and Frying-Type Appliances - UL 1083 Issue:2009/01/09 Ed:6 Rev:2014/05/29 " to "Household Electric Skillets And Frying-Type Appliances [UL 1083:2009 Ed.6+R:15Jul2016]"

180401099SHA

41,2,6,7,9,11 to 23

Delete the UL file number in "Technical data and securement means", add them into "Manufacturer/ trademark" for items 1,2,6,7,9,11 to 23.

8 \ Add the testing information about the change.

12.0 Revision SummaryThe following changes are in compliance with the declaration of Section 8.1:

Section Item Description of Change


Documents

Listing Constructional Data Report (CDR) · ELECTRICAL APPLIANCE CO LTD (E249977) S-A AC 125V, 16A, 50000 cycles, T250, The operating temperature is 190ºC, secured to cooking plate