list of the manuals loaded for PBOil.doc

Project: 20197

Project: 20197 Customer Facing No.: 20197LM2500+G4 - Gas TurbineModec International, Modec International LLCFPSD Cidade de Niteroi MV18, BrazilBulletins

DescriptionPub. Code / Dwg Number

LM2500-IND-029 - Inlet Guide Vane, Stage 1 and Stage 2 Variable Stator Vane Shrouds and Vespel BushingsLM2500-IND-029

LM2500-IND-147 - Variable Stator Vane Torque Shaft Bearing Improvement (LM2500+ Models)LM2500-IND-147

LM2500-IND-169 - Hollow Variable Stator Vane Torque Shaft Upgrade (LM2500+ Models)LM2500-IND-169

LM2500-DDG-102 - LM2500 Addition of Bolts to CRF Mid-Flange Open BoltholesLM2500-DDG-102

LM2500-IND-096 - Stage I HPT Borescope Plug ReplacementLM2500-IND-096

LM2500-IND-022 - Combustor Flame Sensor Sight Glass Assembly ChangeLM2500-IND-022

LM2500-IND-065 - Turbine Rear Frame Insulation KitLM2500-IND-065

LM2500-IND-166 - Water Wash Initiation Button RelocationPB_LM2500-IND-166

LM2500-FN-093 - LM2500 FN-093 Service Bulletin AmendmentLM2500-FN-093

LM2500-CM-062 - Base/Enclosure Exhaust Duct Gusset WeldLM2500-CM-062

LM2500-IND-035 - Vibration Monitoring System ImprovementLM2500-IND-035

LM2500-IND-000 - LM2500 Gas Turbine Generator Set Product Bulletin IndexPB_LM2500-IND-000

LM2500-LHD-024 - Replacement of LSCA Lube Tank Oil Level Switch for Removal of Cadmium Plated Electrical ConnectorLM2500-LHD-024

LM2500-IND-097 - Improved Secondary Liquid Fuel Feeder TubeLM2500-IND-097

LM2500-IND-146 - High Pressure Compressor Rotor Stages 15 and 16 Blade Clearance Increase (LM2500+ Models)LM2500-IND-146

LM2500-CM-058 - High Pressure Turbine Stage 2 Nozzle Improvement (SE ALIFT)LM2500-CM-058

LM2500-IND-199 - Improved Inlet Gearbox Spline AdapterLM2500-IND-199

LM2500-IND-185 - LM2500+ Sump Pressure Ejector Nozzle ImprovementLM2500-IND-185

LM2500-FN-134 - High Pressure Turbine Stage 2 Nozzle ImprovementLM2500-FN-134

LM2500-IND-054 - Wall Thickness Increase for 4R Vent Seal (Cancellation)LM2500-IND-054

LM2500-FN-132 - LM2500 Marine Fire SwitchLM2500-FN-132

LM2500-IND-165 - Balance Piston Seal Serialization (LM2500 and LM2500+ Models)LM2500-IND-165

LM2500-IND-209 - Identified HPRC Stage 1 Disk Assembly Cyclic LifeLM2500-IND-209

LM2500-IND-055 - Improved Bolts and Nuts for Aft Seal CoverLM2500-IND-055

LM2500-USCG-007 - LM2500 LSCA Heat Exchanger Mount Bolts PN L34975P190LM2500-USCG-007

LM2500-IND-137 - High Pressure Compressor Stages 10-13 Spool/Shaft Splined Lock Ring ReplacementLM2500-IND-137

LM2500-IND-093 - Air/Oil Separator Cover improvementLM2500-IND-093

LM2500-IND-142 - Improved Accelerometers (DLE and + Models)LM2500-IND-142

LM2500-DDG-103 - Base/Enclosure Exhaust Duct Gusset WeldLM2500-DDG-103

LM2500-IND-011 - Stage 1 turbine Nozzle SupportLM2500-IND-011

LM2500-IND-155 - Oil Supply Manifold Support Bracket and Cushioned Loop Clamps Introduction (LM2500+ Models)LM2500-IND-155

LM2500-CM-069 - Fuel Metering Valve / Actuator Assembly ContaminationLM2500-CM-069

LM2500-LHD-018 - LM2500 Power Turbine Mount Bolts PN L34975P194LM2500-LHD-018

LM2500-IND-034 - Seventh Stage Blade ModificationLM2500-IND-034

LM2500-USCG-012 - LM2500 Power Turbine Speed Sensor ImprovementLM2500-USCG-012

LM2500-IND-167 - MicroNet/NetCon Pentium NTCPU Loss of CommunicationPB_LM2500-IND-167

LM2500-IND-045 - Improved Borescope PlugsLM2500-IND-045

LM2500-IND-126 - Fuel System Support Brackets (DLE and +DLE models)LM2500-IND-126

LM2500-IND-068 - High Pressure Turbine Rotor (HPTR) Stage 2 Blade (Cancellation)LM2500-IND-068

LM2500-FN-137 - LM2500 Power Turbine Mount Bolts PN L34975P194LM2500-FN-137

LM2500-IND-106 - Removal of Stage 2 Compressor Disk Antirotation PinLM2500-IND-106

LM2500-IND-100 - Increased A ELBO Flow (DLE)LM2500-IND-100

LM2500-IND-169 - Mechanical Pump PrimingPB_LM2500-IND-169

LM2500-IND-165 - K115 Relay in Critical Path LoopPB_LM2500-IND-165

LM2500-IND-129 - Bleed Valve Connectors (DLE and +DLE models)LM2500-IND-129

LM2500-IND-152 - Centerbody Assembly Installation InterferenceLM2500-IND-152

LM2500-CM-071 - LM2500 Power Turbine Speed Sensor ImprovementLM2500-CM-071

LM2500-DDG-107 - Retirement of Gas Generators and Gas Turbines Critical PartsLM2500-DDG-107

LM2500-IND-210 - Identified Stage 10 Thru 13 Compressor Rotor Spool/Shaft Cyclic LifeLM2500-IND-210

LM2500-IND-123 - Stage 2 Power Turbine Disk (LM2500+ Only)LM2500-IND-123

LM2500-IND-124 - Turbine Mid Frame Sump Seal Bore Chamfers (LM250O+ Only)LM2500-IND-124

LM2500-IND-113 - A-Sump Pressurization-Bolt Length (LM2500+ Only)LM2500-IND-113

LM2500-IND-033 - Micro Adjustment - Variable StatorsLM2500-IND-033

LM2500-CM-061 - Retirement of Gas Generators and Gas Turbines Critical PartsLM2500-CM-061

LM2500-IND-181 - Prismic T20 Power System StabilizerPB_LM2500-IND-181

LM2500-IND-130 - High Pressure Compressor Stage 1 Rotor Disk Replacement (LM2500+)LM2500-IND-130

LM2500-IND-115 - No. 5R and No. 6R Static Oil SealsLM2500-IND-115

LM2500-IND-195 - Improved No.4B Stationary Vent Seal ConfigurationLM2500-IND-195

LM2500-IND-087 - HPT Stage 1 Support (Half-Size C Clip)LM2500-IND-087

LM2500-IND-038 - Baffle Air Cover for HPT Stage 1 NozzleLM2500-IND-038

LM2500-IND-189 - LM2500/+ DLE Core Control Improvement Revision S5/S4LM2500-IND-189

LM2500-IND-014 - Inlet Gearbox, P/N L21082G01LM2500-IND-014

LM2500-USCG-009 - Low Pressure Turbine Stator Assembly Part Number ReidentificationLM2500-USCG-009

LM2500-IND-104 - Variable Stator Vane Torque Shaft Bearing Replacement (LM2500+ Only)LM2500-IND-104

LM2500-IND-178 - Removal of Lifting Stickers and Lifting Hardware on LM2500 Package Enclosure HardwarePB_LM2500-IND-178

LM2500-IND-050 - Lube Scavenge Pump and PipingLM2500-IND-050

LM2500-IND-194 - BRUSH AVR (A30, A30-M or MicroAVR Voltage Regulator)PB_LM2500-IND-194

LM2500-USCG-010 - Replacement of LSCA Lube Tank Oil Level Transmitter for Removal of Cadmium Plated Electrical ConnectorLM2500-USCG-010

LM2500-CM-064 - LM2500 LSCA Heat Exchanger Mount Bolts PN L34975P190LM2500-CM-064

LM2500-IND-061 - Deletion of Compressor Rear Frame Vent Screens and Addition of SpacersLM2500-IND-061

LM2500-IND-015 - Replacement of Titanium Compressor Stator VanesLM2500-IND-015

LM2500-IND-079 - Replacement of HPT Aft Shaft Flange Nuts (Cancellation)LM2500-IND-079

LM2500-IND-166 - High Pressure Compressor Discharge Temperature (T3) Sensor Upgrade (LM2500 and LM2500+ Models)LM2500-IND-166

LM2500-IND-167 - Turbine Mid Frame Nozzle Support Bolts Inspection (LM2500 Models)LM2500-IND-167

LM2500-IND-047 - Improved Low Pressure Turbine Stator Stage 2 thru 6LM2500-IND-047

LM2500-FN-140 - Accelerometer Signal ConditionerLM2500-FN-140

LM2500-IND-203 - B-ELBO Orifice Adapter KitLM2500-IND-203

LM2500-IND-084 - Special Inspection of Stage 1 HPT DiskLM2500-IND-084

LM2500-FN-147 - LM2500+G4 Fuel Shutoff Valve ReplacementLM2500-FN-147

LM2500-IND-194 - Igniter Plug Replacement For LM2500 /+ DLE Models OnlyLM2500-IND-194

LM2500-IND-086 - Replacement of Power Turbine (PT) CasesLM2500-IND-086

LM2500-IND-153 - Compressor Rear Frame Expandable Bolt Assembly Introduction (DLE and +DLE Models)LM2500-IND-153

LM2500-IND-162 - Increased Stage 15 High Pressure Compressor Stator Vane Quantity (LM2500+ Models)LM2500-IND-162

LM2500-IND-182 - TM2500 Switchgear Mechanism Incorrect Threaded Rod (Ball Screw)PB_LM2500-IND-182

LM2500-IND-160 - Inlet Gearbox Oil Nozzle ReplacementLM2500-IND-160

LM2500-CM-060 - LM2500 (PF) Gas Turbines with Six Stage Low Pressure Turbine Checking for Cooling Air Holes in Turbine Mid Frame Through Strut No 3LM2500-CM-060

LM2500-IND-144 - High Pressure Compressor Rotor Stages 15 and 16 Blade Clearance IncreaseLM2500-IND-144

LM2500-DDG-106 - LM2500 Power Turbine Mount Bolts PN L34975P194LM2500-DDG-106

LM2500-LHD-021 - LM2500+ Bleed Air Valve RetrofitLM2500-LHD-021

LM2500-IND-064 - Hydraulic Starter, L25105P01LM2500-IND-064

LM2500-IND-020 - External Air Piping Configuration ChangeLM2500-IND-020

LM2500-IND-132 - Stage 14 and Stage 15 Rear Compressor Stator Vane Replacement (Cancellation)LM2500-IND-132

LM2500-IND-191 - LM2500 Synthetic Lube Oil Pressure Transmitter RangePB_LM2500-IND-191

LM2500-IND-196 - Removal of Steel Shot from VSV Torque ShaftsLM2500-IND-196

LM2500-IND-070 - Inspection of compressor aft case horizontal flange veldLM2500-IND-070

LM2500-FN-148 - LM2500 Power Turbine Speed Sensor ImprovementLM2500-FN-148

LM2500-IND-170- Bolted Compressor Rear Frame/Diffuser Introduction (LM2500 DLE and +DEL Models)LM2500-IND-170

LM2500-IND-002 - Compressor Stator Vane Shroud Nuts - Redundant Locking FeatureLM2500-IND-002

LM2500-IND-186 - LM2500+ Air/Oil Separator Manifold and Tube ReplacementLM2500-IND-186

LM2500-IND-031 - Inspection of Number 4R RotatingLM2500-IND-031

LM2500-IND-201 - HPT Cooling Air Tube Stage 13 Orifice Plate Change (ELHS and or Xtend)LM2500-IND-201

LM2500-IND-184 - Pressure Transmitter RecalibrationPB_LM2500-IND-184

LM2500-IND-056 - VSV Control with Tachometer Lever Positive StopsLM2500-IND-056

LM2500-IND-208 - Introduction of New Bolt to Modified High Pressure Compressor Rotor Stage 10-13 SpoolLM2500-IND-208

LM2500-LHD-022 - LM2500 + C-Sump Elastic Joint (LHD)LM2500-LHD-022

LM2500-IND-184 - Igniter Plug ReplacementLM2500-IND-184

LM2500-FN-145 - Fuel Metering Valve / Actuator Assembly ContaminationLM2500-FN-145

LM2500-IND-120 - High Pressure Turbine Forward Shaft Spline Root Radius (LM2500+ Only)LM2500-IND-120

LM2500-IND-072 - Installation of Steam Baffle to Compressor Rear FrameLM2500-IND-072

LM2500-IND-049 - -Variable Stator Vane Actuation System Wear FixLM2500-IND-049

LM2500-IND-082 - Variable Stator Vane (VSV) ControlLM2500-IND-082

LM2500-IND-148 - Accessory Gearbox Gearshaft ReplacementLM2500-IND-148

LM2500-IND-099 - Upgraded TMF and LPT Case FlangesLM2500-IND-099

LM2500-IND-154 - Variable Stator Vane LVDT/T2 Electrical Harness Replacement (LM2500+ Models)LM2500-IND-154

LM2500-DDG-113 - Fuel Metering Valve/Actuator Assembly ContaminationLM2500-DDG-113

LM2500-IND-158 - Acoustic Baffle Seal Simplification (DLE and +DLE Models)LM2500-IND-158

LM2500-IND-004 - Variable Stator Actuating Pushrods - Replacement of Attaching HardwareLM2500-IND-004

LM2500-IND-007 - Air/Oil CoolerLM2500-IND-007

LM2500-IND-090 - Main Shaft BearingsLM2500-IND-090

LM2500-IND-046 - Cooling Air and Vent Seal Tube BracketsLM2500-IND-046

LM2500-IND-149 - Gas Fuel Manifold Retaining Strap Replacement (LM2500 SAC and +SAC Models)LM2500-IND-149

LM2500-FN-135 - LM2500 (PF) Gas Turbines with Six Stage Low Pressure Turbine Checking for Cooling Air Holes in Turbine Mid Frame Through Strut No 3LM2500-FN-135

LM2500-IND-012 - LM2500 Fuel Noxxles, P/N L21045P03 and L21045P06LM2500-IND-012

LM2500-IND-052 - Turbine Mid Frame Liner Solid Anti-Rotation PinsLM2500-IND-052

LM2500-IND-062 - Pneumatic System (STIG) - Replacement of Stage 13 Air tube ElbowsLM2500-IND-062

LM2500-FN-142 - Improved Fire Detection SystemLM2500-FN-142

LM2500-IND-171 - Atlas PC Controls UL/ATEX ListingPB_LM2500-IND-171

LM2500-IND-161 - Stage 16 High Pressure Compressor Rotor Blade Replacement (LM2500+ Models)LM2500-IND-161

LM2500-IND-071 - Variable Stator Vane Actuator (VSV) Product ImprovementLM2500-IND-071

LM2500-AOE-099 - LM2500 PF Gas Turbine with Six Stage Low Pressure Turbine Checking for Cooling Air Holes in Turbine Mid Frame Through Strut No 3LM2500-AOE-099

LM2500-IND-192 - LM2500+ Variable Stator Vane Hardware Durability ImprovementsLM2500-IND-192

LM2500-IND-026 - Modification of HPTR Thermal ShieldLM2500-IND-026

LM2500-CM-065 - LM2500 + Air/Oil Separator Manifold and Tube ReplacementLM2500-CM-065

LM2500-IND-145 - High Pressure Compressor Rotor Stage 10 Blade Clearance increase (LM2500+ Models)LM2500-IND-145

LM2500-IND-173 - Gas Generator Lift Crane Assembly for LM2500+ HSPT PackagesPB_LM2500-IND-173

LM2500-IND-021 - Flame Sensor Bracket ChangeLM2500-IND-021

LM2500-IND-010 - Compressor Inlet Temperature Sensor, P/N L21058P01LM2500-IND-010

LM2500-IND-122 - Electrical Chip DetectorsLM2500-IND-122

LM2500-IND-091- Forward Nozzle Ejector Tube for P-Series Gas TurbinesLM2500-IND-091

LM2500-IND-030 - Modification of No. 3 Bearing JournalLM2500-IND-030

LM2500-CM-066 - LM2500+ Variable Stator Vane Hardware Durability ImprovementsLM2500-CM-066

LM2500-IND-168 - Compressor Rear Frame Seal Support Replacement (LM2500 and LM2500+ Models)LM2500-IND-168

LM2500-IND-186 - Fire Protection Panel Release Module ReplacementPB_LM2500-IND-186

LM2500-IND-039 - Update of 4B Bearing Thrust Balance SystemLM2500-IND-039

LM2500-IND-131 - High Pressure Turbine Rotor Spacer Replacement (LM2500+)LM2500-IND-131

LM2500-AOE-103 - Retirement of Gas Generators and Gas Turbines Critical PartsLM2500-AOE-103

LM2500-IND-182 - LM2500 Base Low Power Operation VSV Link System Kit IntroductionLM2500-IND-182

LM2500-IND-175 - Addition of Thermal Barrier Coating to Turbine Mid Frame CaseLM2500-IND-175

LM2500-IND-101 - High Pressure Turbine Stage 1 Nozzle Leaf Seal Doubler Addition (DLE)LM2500-IND-101

LM2500-IND-138 - Hydraulic Pump Housing and Hydraulic Filter Stud Interference (LM2500+ Models)LM2500-IND-138

LM2500-IND-095 - High Pressure Turbine Stage 1 Nozzle Leaf Seals (DLE)LM2500-IND-095

LM2500-FN-138 - Base/Enclosure Exhaust Duct Gusset WeldLM2500-FN-138

LM2500-IND-198 - Improved VSV Pump and ControlLM2500-IND-198

LM2500-IND-179 - Lube and Scavenge Pump - Product ImprovementLM2500-IND-179

LM2500-FN-143 - Conversion of LM2500 Gas Generator (GG262) from Twin Shank to Single Shank ConfigurationLM2500-FN-143

LM2500-IND-042 - LM2500 Variable Geometry Control System Upgrade for Stator ActuatorsLM2500-IND-042

LM2500-IND-060 - RCANX Forward Shaft Pilot Diameter Increase for Twin Shank High Pressure Turbine RotorsLM2500-IND-060

LM2500-IND-172 - High Pressure Compressor Stage 1 Blade Squealer Tip - Dimension Correction (LM2500+ Models)LM2500-IND-172

LM2500-IND-053 - VSV Control Feedback Cable Bracket ModificationLM2500-IND-053

LM2500-IND-083 - Compressor Rear Case InspectionLM2500-IND-083

LM2500-IND-051 - 8th Stage Air Tube BracketingLM2500-IND-051

LM2500-IND-044 - Modification of Transfer GearboxLM2500-IND-044

LM2500-IND-112 - Change of Circumferential Flange Bolts (DLE Only)LM2500-IND-112

LM2500-IND-001 - Retrofit of Cennecting Links - Variable Vane Actuating RingsLM2500-IND-001

LM2500-IND-108 - No. 3R and No. 5R Damper Bearing UpgradeLM2500-IND-108

LM2500-IND-109 - Variable Stator Feedback Bellcrank And Rerigging Of Variable Stator Vane Stages 5 And 6LM2500-IND-109

LM2500-IND-191 - CRF Mid Flange RedesignLM2500-IND-191

LM2500-IND-164 - 2-Cup Fuel Nozzle Improvement (LM2500+ DLE Models)LM2500-IND-164

LM2500-IND-103 - Compressor Rear Frame to Turbine Mid Frame Alternate Bolt Introduction (LM2500+ DLE Only)LM2500-IND-103

LM2500-IND-128 - Low Pressure Turbine Nozzle Locks (LM2500+)LM2500-IND-128

LM2500-IND-163 - MicroNet and NetCon 16 Channel RelayPB_LM2500-IND-163

LM2500-IND-143 - Increased Area Dual Fuel NozzlesLM2500-IND-143

LM2500-AOE-101 - LM2500 Power Turbine Mount Bolts PN L34975P194LM2500-AOE-101

LM2500-LHD-019 - LM2500 Air/Oil Separator and Flex Joint Hose Clamp ReplacementLM2500-LHD-019

LM2500-IND-204 - LM2500 Base Dual Fuel DLE Liquid Fuel Purge Tubing RedesignLM2500-IND-204

LM2500-IND-080 - Hardcoat of TMF Liner and Liner SupportLM2500-IND-080

LM2500-IND-181 - Compressor Rear Frame Baffle ImprovementLM2500-IND-181

LM2500-AOE-102 - LM2500 LSCA Heat Exchanger Mount Bolts PN L34975P190LM2500-AOE-102

LM2500-IND-176 - LM2500+ High Speed Power Turbine Junction Box Oil AccumulationPB_LM2500-IND-176

LM2500-IND-141 - Improved High Pressure Compressor Rotor Stage 2 Disk (LM2500+ Only)LM2500-IND-141

LM2500-IND-058 - Turbine Mid Frame Liner (Twin Shank) Creep Life InspectionLM2500-IND-058

LM2500-IND-009 - LM2500 Turbine Frame Outer Aft Seal, P/N 9652M53P03LM2500-IND-009

LM2500-IND-023- Installation of Optional Chromel-Alumel Lube Oil Temperature Sensors in Place of Baseline Configuration Resistance Temperature SensorsLM2500-IND-023

LM2500-IND-037 - 1C6884 Gas Turbine Horizontal Maintenance StandLM2500-IND-037

LM2500-IND-077 - Power Turbine Stage 3 Nozzle Segment Tang InspectionLM2500-IND-077

LM2500-IND-005 - Speed Sensor Output Clevis WearLM2500-IND-005

LM2500-IND-119 - Ejector Nozzle Tube - Variable Stator Vane Rub Button Interference (LM2500+ Only)LM2500-IND-119

LM2500-IND-017 - Fuel and Lube System Temperature ProtectionLM2500-IND-017

LM2500-IND-135 - C-Manifold Fuel Supply Tube Replacement (DLE and +DLE Models)LM2500-IND-135

LM2500-IND-200 - No.4B Vent Seal DeflectorLM2500-IND-200

LM2500-IND-173 - Woodward Hydraulic Pump Screw ReplacementLM2500-IND-173

LM2500-IND-207 - CDP Seal Damper ImplementationLM2500-IND-207

LM2500-LHD-026 - Serial Number Assignment for LHA6 Propulsion System PS5005LM2500-LHD-026

LM2500-IND-133 - Acoustic Sensor Mounting Hardware Replacement (DLE and +DLE Models)LM2500-IND-133

LM2500-LHD-023 - Upgrade of E4 Connector with T/C Sockets for LHD 8/LH A 6LM2500-LHD-023

LM2500-IND-059 - Improved Stage 13 Bolting and Non-Bushed Stage 11-13 SpoolLM2500-IND-059

LM2500-IND-078 - LPT Nozzle Support ModificationLM2500-IND-078

LM2500-IND-214 - Introduction of Heat Deflector to Stop Hot Air Impingement on the No.13 Fuel Nozzle Tube/Hose AssemblyLM2500-IND-214

LM2500-IND-000 - LM2500 Industrial Gas Generator/Gas Turbine Service Bulletin Index LM2500-IND-000

LM2500-CM-051 - Woodwa rd Liquid Fuel ValvePB_LM2500-CM-051

LM2500-IND-127 - T5.4 Harness Support Bracket Interference (LM2500+)LM2500-IND-127

LM2500-IND-169 - Supplement - Mechanical Pump Priming PB_LM2500-IND-169-SUP

LM2500-IND-192 - LM2500 VAR Shed LogicPB_LM2500-IND-192

LM2500-DDG-108 - Accelerometer Signal ConditionerLM2500-DDG-108

LM2500-IND-089 - C-Sump Static Oil Seals (Cancellation)LM2500-IND-089

LM2500-IND-185 - Integrated Generator Protection System Output Configuration ChangesPB_LM2500-IND-185

LM2500-IND-118 - Combustor Baffle Contamination (DLE Only)LM2500-IND-118

LM2500-DDG-110 - LM2500 Electrical Connector Kit Replacement of Connector PN L44551P15LM2500-DDG-110

LM2500-IND-193 - LM2500+ Sump Vent Line Elastic Joint R eplacementLM2500-IND-193

LM2500-IND-177 - Retirement of Gas Generators and Gas Turbines Critical PartsLM2500-IND-177

LM2500-IND-151 - Dual-Element Lube System Resistance Temperature Detector (LM2500 SACLM2500-IND-151

LM2500-IND-190 - Introduction of Tiolube Bolts to Turbine Mid Frame Low Pressure Turbine Nozzle Support, Not Conforming with Service Bulletin LM2500-IND-0187LM2500-IND-190

LM2500-IND-140 - Acoustic Sensor System Improvement (DLE and +DLE Models)LM2500-IND-140

LM2500-IND-105 - Improved B-Sump Insulation Blankets and No. 4R Bearing Heat ShieldLM2500-IND-105

LM2500-USCG-004 - Retirement of Gas Generators and Gas Turbines Critical PartsLM2500-USCG-004

LM2500-IND-187 - Turbine Mid Frame Hardware to Update Low Pressure Turbine Nozzle SupportsLM2500-IND-187

LM2500-IND-110 - Conversion of Rigid Gas Feeder Tubes to Flexible Gas Feeder TubesLM2500-IND-110

LM2500-DDG-111 - Low Pressure Turbine Stator Assembly Part Number ReidentificationLM2500-DDG-111

LM2500-IND-066 - Fuel Manifold and Fuel Feeder Tube Assembly Replacement (Cancellation)LM2500-IND-066

LM2500-IND-156 - Stage 8 Bleed Function Elimination (LM2500 DLE Models)LM2500-IND-156

LM2500-IND-081 - RCANX Turbine Mid Frame Hardware to Update Low Pressure Turbine Nozzle SupportsLM2500-IND-081

LM2500-IND-170 - Meidensha Generator Coupling Guard Rain ShieldPB_LM2500-IND-170

LM2500-IND-102 - Inlet Gearbox Assembly - Cap ImprovementLM2500-IND-102

LM2500-IND-028 - Improved Stage 2 HPT Nozzle AssemblyLM2500-IND-028

LM2500-IND-183 - Weston Aerospace Motional Pickup Transducer (Speed Probe) Replacement (LM 2000, LM2500, and LM2500+ Models)LM2500-IND-183

LM2500-IND-211 - B-Sump Thermal Insulation Blankets w ith Non-Conforming InsulationLM2500-IND-211

LM2500-IND-111 - Compressor Rear Frame Seal Support ReplacementLM2500-IND-111

LM2500-IND-019 - Accelerometer Bracket - ReplacementLM2500-IND-019

LM2500-IND-202 - LM2500 Turbine Mid Frame with Improved DurabilityLM2500-IND-202

LM2500-IND-036 - Compressor Rear Frame Borescope Port BossesLM2500-IND-036

LM2500-IND-197 - LM2500 Gas Turbines with Six Stage Low Pressure Turbine - Checking for Cooling Air Holes in Turbine Mid Frame through Strut No. 3LM2500-IND-197

LM2500-IND-188 - Exhaust Access Panel Gap Leakage RepairPB_LM2500-IND-188

LM2500-DDG-114 - LM2500 Power Turbine Speed Sensor ImprovementLM2500-DDG-114

LM2500-IND-174 - Compressor Rotor Stage 15 Locking Blade Replacement (LM2500 and LM2500+ Models)LM2500-IND-174

LM2500-FN-139 - LM2500 LSCA Heat Exchanger Mount Bolts PN L34975P190LM2500-FN-139

LM2500-IND-085 - No. 3 Oil/Air Seals High Temp CapabilityLM2500-IND-085

LM2500-IND-092 - Turbine Mid Frame/Low Pressure Turbine Flange BoltsLM2500-IND-092

LM2500-IND-098 - Improved No. 4R Bearing Vent SealLM2500-IND-098

LM2500-FN-144 - High Pressure Turbine Stage 2 Nozzle ImprovementLM2500-FN-144

LM2500-IND-117 - Individually Replaceable T5.4 Probes and HarnessesLM2500-IND-117

LM2500-IND-074 - Replacement of Steam Baffle on Compressor Rear FrameLM2500-IND-074

LM2500-IND-013 - LM2500 Starter Lube System ModificationLM2500-IND-013

LM2500-IND-159 - Improved Combustor and 3-Cup Fuel Nozzle (LM2500+DLE Models)LM2500-IND-159

LM2500-USCG-011 - Fuel Metering Valve/Actuator Assembly ContaminationLM2500-USCG-011

LM2500-IND-183 - TM2500 DC Lube Motor/ Pump Check Valve ReplacementPB_LM2500-IND-183

LM2500-DDG-112 - Replacement of LSCA Lube Tank Oil Level Transmitter for Removal of Cadmium Plated Electrical ConnectorLM2500-DDG-112

LM2500-IND-116 - Turbine Mid Frame Lube Supply Line WearLM2500-IND-116

LM2500-IND-164 - LM2500 Lineside and Neutral Cubicle Water IngressPB_LM2500-IND-164

LM2500-IND-205 - LM2500/+ Improved #3 Stationary Oil Seal ChangeLM2500-IND-205

LM2500-IND-180 - Brush Automatic Voltage Regulator Under Excitation Limiter SettingsPB_LM2500-IND-180

LM2500-IND-006 - Variable Stator Vane Position IndicatorLM2500-IND-006

LM2500-IND-136 - Low Pressure Turbine Case Aft Flange Bolt Replacement (LM2500+ Models)LM2500-IND-136

LM2500-IND-040 - Continuous Lubrication StarterLM2500-IND-040

LM2500-IND-043 - LM2500 Variable Geometry Control System Update for Speed SensorLM2500-IND-043

LM2500-FN-141 - LM2500 Air Starter Hose Kit Bolts , PN L34975P169LM2500-FN-141

LM2500-USCG-003 - LM2500 (PF) Gas Turbines with Six Stage Low Pressure Turbine Checking for Coolong Air Holes in Turbines Mid Through Strut No 3 (Deepwater)LM2500-USCG-003

LM2500-IND-069 - Replacement of Brazed Natural Gas Fuel Nozzles and Gas Fuel/Steam Nozzles (Product Improvement) (Cancellation)LM2500-IND-069

LM2500-IND-094 - Inspection of High Pressure Compressor Rotor Aft Shaft External ThreadsLM2500-IND-094

LM2500-IND-168 - Salem Mark V LM Loss of CommunicationPB_LM2500-IND-168

LM2500-IND-180 - Compressor Rotor Stage 15 Vane and Stage 16 Blade Improvement (LM2500 Models)LM2500-IND-180

LM2500-CM-068 - Replacement of LSCA Oil Level Lube Tank Switch for Removal of Cadmium Plated Electrical Connector - SealiftLM2500-CM-068

LM2500-USCG-006 - LM2500 Power Turbine Mount Bolts PN L34975P194LM2500-USCG-006

LM2500-IND-157 - Sump Vent Line Elastic Joint Replacement (LM2500+ Models)LM2500-IND-157

LM2500-IND-139 - High Pressure Compressor Rotor Rear Stages ReplacementLM2500-IND-139

LM2500-IND-088 - LPT Stage 1 Nozzle for PH ModelsLM2500-IND-088

LM2500-FN-136 - Retirement of Gas Generators and Gas Turbines Critical PartsLM2500-FN-136

LM2500-IND-073 - Introduction of P/N 901M37P68 Igniter PlugLM2500-IND-073

LM2500-IND-178 - 9th Stage Air Line Bracket ChangeLM2500-IND-178

LM2500-IND-175 - LM2500/+ and TM2500 Package Gas Fuel Piping/Tubing Plug InspectionPB_LM2500-IND-175

LM2500-LHD-020 - Retirement of Gas Generators and Gas Turbines Critical PartsLM2500-LHD-020

LM2500-IND-174 - LM2500+HSPT Turbine Enclosure Fall Protection Safety RailsPB_LM2500-IND-174

LM2500-IND-125 - High Pressure Turbine Rotor Thermal Shield Inspection (Twin-Shank)LM2500-IND-125

LM2500-IND-067 - High Pressure Compressor Stage 14 Through 16 Rotor Spool (Cancellation)LM2500-IND-067

LM2500-IND-048 - Improved T5.4 LeadLM2500-IND-048

LM2500-IND-063 - Transfer Gearbox Assembly Bolt ReplacementLM2500-IND-063

LM2500-FN-000 - LM2500 International Marine Gas Generator/Gas Turbine Service Bulletin IndexLM2500-FN-000

LM2500-IND-075 - Replacement of Inlet Gearbox Horizontal Gearshaft and Plain Nut (Cancellation)LM2500-IND-075

LM2500-LHD-017 - LM2500 LSCA Heat Exchanger Mount Bolts, PNL34975P190LM2500-LHD-017

LM2500-IND-176 - Introduction of EABAL Software Change (LM2500+ DLE Models)LM2500-IND-176

LM2500-IND-032 - Improved Power Turbine Stage 1 Interstage SealLM2500-IND-032

LM2500-IND-134 - High Pressure Compressor (HPC) Stage 8 Stator Vane Replacement (LM2500+ Only) (Cancellation)LM2500-IND-134

LM2500-IND-150 - High Pressure Turbine Rotor Blade Seal Replacement (LM2500+ Models Only)LM2500-IND-150

LM2500-IND-107 - Variable Stator Vane Servovalve Fail Safe Operation (LM2500+)LM2500-IND-107

LM2500-IND-212 - Improved Temperature Compressor Discharge Sensor (T3 )LM2500-IND-212

LM2500-LHD-025 - Fuel Metering Valve/Actuator Assembly ContaminationLM2500-LHD-025

LM2500-IND-114 - High Pressure Turbine Rotor Oil Tube Flexible SealLM2500-IND-114

LM2500-IND-171 - Introduction of Software Block Change S4 EABAL (DLE Models)LM2500-IND-171

LM2500-IND-008 - Variable Servo valve Mounting BracketLM2500-IND-008

LM2500-IND-188 - No. 4R Bearing Compressor Discharge Pressure Stationary Air Seal ImprovementLM2500-IND-188

LM2500-IND-076 - Introduction of LPT Stage 1 Nozzle Retaining ClipsLM2500-IND-076

LM2500-LHD-028 - LM2500 + Hydraulic Starter Tube/Hose Assembly ReplacementLM2500-LHD-028

LM2500-IND-027 - Ruggedized Stage 9 Compressor Rotor BladesLM2500-IND-027

LM2500-CM-063 - LM2500 Power Turbine Mount Bolts PN L34975P194 (Sealift)LM2500-CM-063

LM2500-IND-172 - LM2500 Enclosure Door RetainerPB_LM2500-IND-172

LM2500-IND-189 - LM2500 Turbine Enclosure Ventilation Flow DeflectorsPB_LM2500-IND-189

LM2500-IND-025 - Compressor Variable Stator Vane Q8050A Bushings (Cancellation)LM2500-IND-025

LM2500-IND-016 - Replacement of Stage 1 HPC BladesLM2500-IND-016

LM2500-IND-177 - LM2500/+ Gas Fuel Welding AnomalyPB_LM2500-IND-177

LM2500-IND-206 - High Pressure Turbine Rotor Damper Sleeve ReplacementLM2500-IND-206

LM2500-IND-057 - Increase Temperature Resistant Fuel ManifoldLM2500-IND-057

LM2500-IND-018 - Engine ReconfigurationLM2500-IND-018

LM2500-CM-000 - LM2500 Commercial Marine Gas Generator/Gas Turbine Service Bulletin IndexLM2500-CM-000

LM2500-CM-067 - Lube and Scavenge Pump - Product ImprovementLM2500-CM-067

LM2500-IND-213 - New Hydraulic Pump and VSV Servovalve with Improved SplineLM2500-IND-213

LM2500-DDG-109 - LM2500 LSCA Heat Exchanger Mount Bolts PN L34975P190LM2500-DDG-109

LM2500-IND-121 - P2/T2 Sensor Bolt Length (LM2500+ Only)LM2500-IND-121

GEK LM2500 RC


Table of Contentsgek112859_file0026

WP 209 00 Variable Stator Vane Mechanism Replacementgek112859_file0071

Figure 35. Kit, 682L241, Fuel Pressurization Valvegek112860_file0045

Chapter 4 Gas Turbine Assembly Descriptiongek112859_file0008

WP 407 00 Lube Oil Samplinggek112859_file0098

WP 403 00 External Engine Inspectiongek112859_file0094

Figure 23. High Pressure Turbine Rotor Forward Shaft Assembly Breakdowngek112860_file0033

WP 418 00 Variable Stator Vane System Inspectiongek112859_file0110

Figure 33. Flange Hardware Compressor Rear Frame Mid Flangegek112860_file0043

Cover Page GEK 112859gek112859_file0001

WP 221 00 LPT Stage 1 Nozzle Assembly Replacementgek112859_file0086

WP 211 00 High Pressure Compressor Stator Casings Replacementgek112859_file0073

WP 412 00 Overtemperature Inspectiongek112859_file0103

Figure 56. Flange Hardware - Turbine Mid Frame to LPT Stator Assygek112860_file0066

Figure 24. Stage 2 High Pressure Turbine Nozzle Assembly Breakdowngek112860_file0034

Figure 14. Compressor Rear Frame Assembly and Associated Partsgek112860_file0024

Figure 45. Gearbox Forward Right Sidegek112860_file0055

Appendix A6 Specification for Lubricating Oil for GE Aircraft Derivative Gas Turbinesgek112859_file0023

WP 122 00 Hydraulic Filter Housing and Element Replacementgek112859_file0057

Figure 58. Turbine Rear Frame/Seals and Bearinggek112860_file0068

Figure 29. Turbine Hardware Compressor Front Frame to Inlet Duct and Compressor Front Stator Casegek112860_file0039

SWP 101 04 Dual Liquid Manifold Replacementgek112859_file0034

Figure 27. Turbine Mid Frame Sump Assembly Breakdown..gek112860_file0037

WP 121 00 Variable Stator Vane Servovalve Replacementgek112859_file0056

Figure 10. Compressor Section/VSV Actuation System and Torque Shaft Assygek112860_file0020

Figure 31. Flange Hardware Compressor Rear Frame to Rear Compressor Casegek112860_file0041

WP 402 00 External Engine Cleaninggek112859_file0093

WP 423 00 High Pressure Compressor Stator Casings Inspectiongek112859_file0115

WP 409 00 Ignition System Functional Checkgek112859_file0100

WP 408 00 Hydraulic Pump Filter Element Inspectiongek112859_file0099

List of Effective Pagesgek112859_file0025

Figure 01. Major Assembliesgek112860_file0011

Figure 36. Kit, 682L990, Fuel System, Dual Fuel, Watergek112860_file0046

Figure 51. Electrical Immersion Type Resistance Temperature Detectorgek112860_file0061

WP 500 00 Gas Generator/Gas Turbine Preservation, Depreservation, and Storage Maintenancegek112859_file0124

WP 210 00 Compressor Front Frame Replacementgek112859_file0072

SWP 216 01 Two Stage Power Turbine And Gas Generator Joining Kitgek112859_file0079

Figure 32. HPC Forward Case to Rear Casegek112860_file0042

WP 218 00 Six Stage Power Turbine Stator Casings Removal and Installationgek112859_file0083

WP 107 00 Power Turbine Dual Output Speed Transducer Replacementgek112859_file0040

WP 201 00 High Pressure Turbine Rotor Replacementgek112859_file0061

WP 217 00 Gas Generator Miscellaneous Sump Components Replacementgek112859_file0081

Figure 60. Turbine Rear Frame/Accelerometer and Electric Cablegek112860_file0070

WP 103 00 Igniter Plug and Ignition Lead Replacementgek112859_file0037

Figure 50. Electrical VSV/LVDT Cable, Right/Left Sidegek112860_file0060

WP 503 00 Power Turbine Shippinggek112859_file0127

Chapter 7 Installation/Initial Startup and Engine Operationgek112859_file0011

SWP 413 01 Gas Turbine Miscellaneous Sump Components Inspectiongek112859_file0105

Figure 57. Flange Hardware - LPT Stator Assy to Turbine Rear Framegek112860_file0067

SWP 116 01 Air/Oil Separator Cover Replacementgek112859_file0050

Figure 61. Turbine Rear Frame Assy Breakdowngek112860_file0071

Chapter 1 Introductiongek112859_file0005


Figure 07. Transfer Gearbox Assy Breakdowngek112860_file0017

Chapter 10 General Maintenance Practicesgek112859_file0014

WP 301 00 Gas Generator Assembly Replacementgek112859_file0088

Figure 43. Turbine Rear Frame - Oil Supplygek112860_file0053

Figure 11. Torque Shaft Assygek112860_file0021

WP 414 00 Variable Stator Vane Off-Schedule Inspectiongek112859_file0106

Figure 62. Kit, 537L163, Hydraulic Starter Assemblyn and Installationgek112860_file0072

WP 204 00 Gas Generator Inlet Duct Replacementgek112859_file0066

Section I Introductiongek112860_file0005

Figure 38. Left Side Piping Airgek112860_file0048

Figure 42. Left Side Piping - Oilgek112860_file0052

WP 404 00 Gas Turbine Exhaust System Inspectiongek112859_file0095

Cover Page GEK 112860_Agek112860_file0001

Figure 64. Kits, 682L511, 537L369 and 682L960, Ignition Optionsgek112860_file0074

WP 410 00 Vibration Monitoring System Functional Checkgek112859_file0101

SWP 216 02 Gas Generator Joining Kitgek112859_file0080

SWP 101 03 Natural Gas Fuel Manifold Replacementgek112859_file0033

WP 104 00 Ignition Exciter Replacementgek112859_file0038

WP 413 00 Gas Generator Miscellaneous Sump Components Inspectiongek112859_file0104

Figure 15. Compressor Rear Frame Breakdowngek112860_file0025

Figure 53. Power Turbine Sectiongek112860_file0063

Chapter 6 Service and Support Requirementsgek112859_file0010

Chapter 8 Abnormal Operationgek112859_file0012

WP 116 00 Air/Oil Separator Replacementgek112859_file0049

WP 202 00 High Pressure Turbine Rotor Blade Replacementgek112859_file0064

Figure 19. Compressor Rear Frame, Stages 1 and 2 Borescope Plugsgek112860_file0029

Figure 55. Power Turbine Stator Assy Breakdowngek112860_file0065

WP 219 00 Six Stage Power Turbine Stage 1 Rotor Blade Replacementgek112859_file0084

Figure 06. Inlet Gearbox/Transfer Gearbox/Radial Drivegek112860_file0016

WP 411 00 Overspeed Inspectiongek112859_file0102

Figure 49. Electrical Plug Igniter and Associated Partsgek112860_file0059

Appendix A1 Natural Gas Fuel for GE Aircraft Derivative Gas Turbines in Industrial Applicationsgek112859_file0018

Figure 44. Gearbox Forward Left Sidegek112860_file0054

WP 212 00 High Pressure Compressor Variable Stator Vane Replacementgek112859_file0074

Chapter 11 Preventive Maintenancegek112859_file0015

Figure 04. Compressor Front Framegek112860_file0014

Figure 20. High Pressure Turbine Stage 1 Nozzle Assembly Breakdowngek112860_file0030

Figure 26. Turbine Mid Frame Liner Breakdowngek112860_file0036

Table I. How to Use This Illustrated Parts Breakdowngek112860_file0006

Figure 08. Transfer Gearbox Subassemblygek112860_file0018

WP 422 00 Six Stage Power Turbine Stages 1 and 6 Rotor Blade Inspectiongek112859_file0114

Figure 37. Kit, 682L995, Fuel System, Gasgek112860_file0047

Title Page GEK 112859 Volume IIgek112859_file0024

WP 405 00 Water-Washgek112859_file0096

Figure 21. High Pressure Turbine Sectiongek112860_file0031

Figure 09. High Pressure Compressor Rotor Assemblygek112860_file0019

WP 216 00 Gas Generator and Power Turbine Separation and Joininggek112859_file0078

Figure 13. Compressor Rear Stator Assy Breakdowngek112860_file0023

WP 417 00 High Pressure Recoup Metering Spacer Selectiongek112859_file0109

WP 415 00 Fuel System Inspectiongek112859_file0107

SWP 201 01 High Pressure Turbine Stage 2 Nozzle Assembly Replacementgek112859_file0062

WP 504 00 Shipping Container Inspection and Reconditioninggek112859_file0128

WP 208 00 Inlet Gearbox Replacementgek112859_file0070

Chapter 5 LM2500+G4 SAC System Descriptionsgek112859_file0009

SWP 101 02 Dual Fuel Nozzle Replacementgek112859_file0032

WP 416 00 Compressor Front Frame Inspectiongek112859_file0108

WP 419 00 Thermocouple Probe (T5.4) Inspectiongek112859_file0111

Figure 05. Inlet Gearbox Assy Breakdowngek112860_file0015

WP 424 00 High Pressure Compressor Rotor Inspectiongek112859_file0116

WP 108 00 Thermocouple Probe (T5.4) and Harness Replacementgek112859_file0041

WP 406 00 Borescope Inspectiongek112859_file0097

Cover Page GEK 112860_Bgek112860_file0002

Appendix A3 Liquid Detergent for Compressor Cleaning for GE Aircraft Derivative Gas Turbines in Industrial Applicationsgek112859_file0020

Numerical Indexgek112860_file0075

Figure 22. High Pressure Turbine Rotor Assembly Breakdowngek112860_file0032

SWP 217 01 Gas Turbine Miscellaneous Sump Components Replacementgek112859_file0082

WP 502 00 Gas Generator/Gas Turbine Shippinggek112859_file0126

Figure 34. Flange Hardware Compressor Rear Frame to Turbine Mid Framegek112860_file0044

WP 425 00 Single Annular Combustor Inspectiongek112859_file0117

Appendix A5 Water Purity Specification for NOx Suppression in GE Aircraft Derivative Gas Turbines in Industrial Applicationsgek112859_file0022

Figure 41. Bottom Piping - Air and Oilgek112860_file0051


SWP 201 02 High Pressure Turbine Stage 1 Nozzle Assembly Replacementgek112859_file0063

Table V. Publication Change Requestgek112860_file0010

Figure 54. Power Turbine Rotor Assy Breakdowngek112860_file0064


Table IV. Substitute Packingsgek112860_file0009

WP 430 00 High Pressure Compressor Variable Stator Vane Shrouds Inspectiongek112859_file0122

WP 002 00 General Maintenance Practicesgek112859_file0028

WP 426 00 High Pressure Turbine Rotor Inspectiongek112859_file0118

Figure 18. Combustion Chamber Liner Assembly Breakdowngek112860_file0028

Figure 59. Turbine Rear Frame/Lube Nozzle and Speed Sensor Housinggek112860_file0069

SWP 113 01 Gas Turbine Outside Piping and Wiring Removal and Installationgek112859_file0047

Chapter 9 Troubleshootinggek112859_file0013

WP 100 00 Variable Stator Vane Actuator Replacementgek112859_file0029

Figure 39. Top Piping Airgek112860_file0049

WP 001 00 Numerical List of Support Equipment and List of Consumable Materialsgek112859_file0027

WP 200 00 Turbine Mid Frame Replacementgek112859_file0060

Figure 40. Right Side Piping - Airgek112860_file0050

WP 214 00 High Pressure Compressor Fixed Stator Vane Replacementgek112859_file0076

WP 213 00 High Pressure Compressor Variable Stator Vane Shroud Replacementgek112859_file0075

WP 220 00 Power Turbine Forward Adapter Replacementgek112859_file0085

WP 124 00 Magnetic Detector Plug Replacementgek112859_file0059

Appendix A2 Compressor Cleaning Water Purity Specification for GE Aircraft Derivative Gas Turbines in Industrial Applicationsgek112859_file0019

WP 215 00 High Pressure Compressor Rotor Blades Replacementgek112859_file0077

WP 118 00 Ultraviolet Flame Sensing System Components Replacementgek112859_file0053

WP 429 00 Turbine Mid Frame Inspectiongek112859_file0121

WP 113 00 Gas Generator Outside Piping and Wiring Removal and Installationgek112859_file0046

Figure 16. Compressor Rear Frame Sump Housinggek112860_file0026

Figure 28. Turbine Mid Frame/Stg 1 LPT Nozzle and No. 6 Bearinggek112860_file0038

WP 119 00 Accessory Gearbox Carbon Seals Replacementgek112859_file0054

Figure 46. Total Pressure, T5.4 Thermocouple Probes and Associated Partsgek112860_file0056

WP 203 00 Single Annular Combustor Replacementgek112859_file0065

Chapter 12 Critical Parts Life Management for LM2500+G4 Industrial Gas Turbinesgek112859_file0016

WP 428 00 High Pressure Turbine Stage 2 Nozzle Inspectiongek112859_file0120


WP 420 00 Accessory Gearbox Inspectiongek112859_file0112

Figure 02. Inlet Duct and Centerbodygek112860_file0012

WP 110 00 Lube System Temperature Sensor Replacementgek112859_file0043

Chapter 2 Gas Generator/Gas Turbine General Description, Model Summary, and Heritagegek112859_file0006

Figure 03. Compressor Front Frame and Associated Partsgek112860_file0013

Figure 47. Electrical - Compressor Discharge Temperaturegek112860_file0057

SWP 101 01 Natural Gas Fuel Nozzle Replacementgek112859_file0031

WP 123 00 High Pressure Compressor Discharge Temperature (T3) Sensor Replacementgek112859_file0058

WP 400 00 Lube and Scavenge Pump Screen, Electronic Chip Detector, and Magnetic Detector Plug Inspectiongek112859_file0091

WP 427 00 High Pressure Turbine Stage 1 Nozzle Inspectiongek112859_file0119

WP 421 00 Six Stage Power Turbine Components Inspectiongek112859_file0113

SWP 117 01 Hydraulic Starter Replacementgek112859_file0052

WP 112 00 Power Turbine Inlet Pressure (P5.4) Probe Replacementgek112859_file0045

WP 120 00 Hydraulic Pump Replacementgek112859_file0055

Appendix A4 Liquid Fuel Requirements for GE AeroDerivative Gas Turbinesgek112859_file0021

WP 105 00 Gas Generator Speed Sensor Replacementgek112859_file0039

Figure 63. Kit, 682L514, PS3 Reducer Tubegek112860_file0073

WP 102 00 Five Element Lube and Scavenge Pump Replacementgek112859_file0035

WP 114 00 Variable Stator Vane Torque Shaft Replacementgek112859_file0048

WP 206 00 Accessory Gearbox Replacementgek112859_file0068

Figure 17. Compressor Rear Frame Aft Support, Seals, and High Pressure Turbine Nozzlesgek112860_file0027

Table III. Abbreviationsgek112860_file0008

WP 207 00 Radial Drive Shaft Replacementgek112859_file0069

WP 111 00 Accelerometer Replacementgek112859_file0044

WP 117 00 Pneumatic Starter (Shrouded/Nonshrouded) Replacementgek112859_file0051

Figure 25. Turbine Mid Frame Assembly and Bearingsgek112860_file0035

Figure 30. Flange Hardware Front Compressor Case Stator Bossesgek112860_file0040

WP 302 00 Power Turbine Assembly Replacementgek112859_file0089

Figure 12. High Pressure Compressor Stator Breakdowngek112860_file0022

WP 401 00 Gas Generator Inlet Inspectiongek112859_file0092

Figure 52. Nozzle Assy, Stg 1 - LPTgek112860_file0062

WP 300 00 Gas Turbine Assembly Replacementgek112859_file0087

WP 109 00 High Pressure Compressor Inlet Pressure/Temperature (P2/T2) Sensor Replacementgek112859_file0042

Title Page GEK 112859 Volume Igek112859_file0002

WP 205 00 Centerbody Replacementgek112859_file0067

SWP 102 01 Six Element Lube and Scavenge Pump Replacementgek112859_file0036

Chapter 3 Gas Turbine Packagegek112859_file0007

WP 303 00 Maintenance Dolly Usagegek112859_file0090

WP 501 00 Power Turbine Preservation, Depreservation, and Storage Maintenancegek112859_file0125

WP 101 00 Fuel System Replacementgek112859_file0030

WP 431 00 Power Turbine Thrust Balance Cavity Pressure System Orifice Plate Selectiongek112859_file0123

Appendix A Gas and Liquid Fuel, Water, and Detergent Requirementsgek112859_file0017

Figure 48. Electrical - Gas Generator Accelerometergek112860_file0058

Table II. Glossary of Termsgek112860_file0007

Installation and Commissioning Manual


IWP03 - Post-Pour EmbedmentsICM_LM2500_IWP03

Control Valve CalibrationController

IWP21 - DC-UPS InstallationICM_LM2500_IWP21-LSPT

Draw Out Air Circuit BreakersDrawoutair

Medium Voltage Motor StartersMedvoltmotor

cautionsCautions

PWP11 - Water Wash System Pre-CommICM_LM2500_PWP11-LSPT

IWP18 - LF Booster Skid InstallationICM_LM2500_IWP18-LSPT

IWP10 - Install Inlet Filter HouseICM_LM2500_IWP10

Power Transformer Check ListPwrtrans

Expansion Joint AlignmentExjoint

IWP13 - Install Line and Neutral CubiclesICM_LM2500_IWP13-LSPT

Installation & Commissioning Procedure LM6000Certaccept

CWP19 - AVR Static TestingICM_LM2500_CWP19-LSPT

Shaft Rotation LogShrotat

Precommissioning ProcedurePrecommproc

PWP06 - DLE Gas Fuel System Pre-CommICM_LM2500_PWP06

Pressure Test LogPrestestlog

Cable Reel LogCablreel

Transmitter CalibrationXmittercal

Ground-Earthing InspectionGrdearth

Inspection of Packaged EquipmentInspequip

CWP22 - Power AscentionICM_LM2500_CWP22-LSPT

Grout ReleaseGrelease

IWP12 - Install Combustion ExhaustICM_LM2500_IWP12-LSPT

Front Matter

Mechanical Alignment Form Direct Indicator ReadingMechdirect

Front Matter Acknowledgement Milestone

IWP24 - Generator Dress-OutICM_LM2500_IWP24-LSPT

CWP18 - Pre-Start TestingICM_LM2500_CWP18-LSPT

Installation & Commissioning Procedure LM6000Certreadycomm

Power Transmission Sheave AlignmentPwrsheav

Nonconformance ReportNonconfreport

PWP14 - DC-UPS System Pre-CommICM_LM2500_PWP14

IWP06 - Centerline AlignmentICM_LM2500_IWP06-LSPT

PWP17 - Low Voltage AC and DC System Pre-CommICM_LM2500_PWP17-LSPT

IWP11 - Install Inlet Filter House (Evap)ICM_LM2500_IWP11

IWP19 - Gas Fuel Coalescer Skid InstallationICM_LM2500_IWP19

Pressure Indicator Check ListPressindck

PWP13 - Control System Pre-CommICM_LM2500_PWP13-LSPT

Loop StatusLoopstat

IWP22 - Off-Site Monitoring InstallationICM_LM2500_IWP22

Cable Termination LogCablterm

Cable Dielectric TestDielectric

Control Cable ScheduleCabsched

Dry Type Transformers Megger and InspectionDrytype

Switchgear and Switchboard Assemblies Check ListSwitchcheck

Pipe Blowdown and Cleaning LogPipeblow

Lighting Distribution Panel Boards Megger ReportLtningdist

PWP05 - Gas Fuel System Pre-CommICM_LM2500_PWP05-LSPT

IWP05 - Set and Level Turbine PackageICM_LM2500_IWP05-LSPT

Indicator CalibrationIndical

CWP24 - Controls Backup (CDROM)ICM_LM2500_CWP24-LSPT

IWP26 - Mechanical Walk DownICM_LM2500_IWP26-LSPT

Mechanical Alignment Form Optalign ReadingMechopta

Underground Pipe Test RecordUgpipetest

IWP16 - Fin Fan Cooler Skid InstallationICM_LM2500_IWP16-LSPT

Pressure Test ReportPrestest

PWP15 - High Voltage System Pre-CommICM_LM2500_PWP15-LSPT

Mechanical Completion Milestone

Installation & Commissioning Procedure LM6000Certmech

MCC StartersMccstart

Loop CheckLoopchk

PWP09 - Vent-Comb Air (EVAP) Pre-CommICM_LM2500_PWP09

Controller CalibrationCntrlvalve

IWP07 - Install Package VentilationICM_LM2500_IWP07

Commissioning Closeout Milestone

Flushing, Cleaning, Inspection & Closure ReportFlush

IWP02 - Pre-Pour EmbedmentsICM_LM2500_IWP02

Unit Substation Check List (Page 1 of 3)Unitsub

IWP17 - Fire Supression Skid InstallationICM_LM2500_IWP17-LSPT

IWP14 - Aux Skid InstallationICM_LM2500_IWP14-LSPT

Lubrication TagLubetag

CWP23 - Combustor MappingICM_LM2500_CWP23

PWP02 - GLO System Pre-CommICM_LM2500_PWP02-LSPT

PWP07 - Hydraulic Start System Pre-CommICM_LM2500_PWP07-LSPT

PWP03 - Fire System Pre-CommICM_LM2500_PWP03-LSPT

Medium Voltage Air SwitchesMedvolt

Power Cable SchedulePowrcabsch

Gauge Calibration Control LogGaugelog

Punchlist ProcessPunchlist

Pipe Pressure Leakage TestPipeleak

Conveyor Pulley AlignmentConvpull

IWP25 - Filter House Dress-OutICM_LM2500_IWP25-LSPT

Installation & Commissioning Procedure LM6000Preface

Wire and Insulation Resistance TestsWireinsresist

Motor Test and MCC Starter Data SheetMotortest

IWP27 - Electrical Walk DownICM_LM2500_IWP27-LSPT

PWP01 - TLO System Pre-CommICM_LM2500_PWP01-LSPT

Jeep Test ReportJeeptest

IWP15 - GLO Skid InstallationICM_LM2500_IWP15

Installation & Commissioning Procedure LM6000Certcommcomp

Gauge Calibration ReportGaugereport

Generators, Synchronous and Wound Rotor MotorsGenmotors

Motor Run-In RecordMotorrun

Motor Control Center Sections Checklist and Meg SheetMotorcntrl

IWP09 - Install Intake Plenum and Fliter HouseICM_LM2500_IWP09-LSPT

PWP08 - Vent-Comb Air System Pre-CommICM_LM2500_PWP08-LSPT

IWP01 - Receive-Stage EquipmentICM_LM2500_IWP01-LSPT

Transfer Of Care, Custody And Control LetterTransferlttr

PWP12 - Water Injection System Pre-CommICM_LM2500_PWP12

PWP16 - Medium Voltage System Pre-CommICM_LM2500_PWP16

EQUIPMENT INSTALLATION LOGEquiplog

Nonconformance LogNonconflog

Bus Duct Check ListBusduct

PWP04 - Liquid Fuel System Pre-CommICM_LM2500_PWP04-LSPT

IWP20 - TCP InstallationICM_LM2500_IWP20-LSPT

CWP20 - First FireICM_LM2500_CWP20-LSPT

Construction Release to Start-UpConstrrelease

First Fire Readiness Milestone

IWP28 - Centerline PSORICM_LM2500_IWP28-LSPT

Ground Systems Test RecordGrdtest

Installation & Commissioning Procedure LM6000Installcommproc

IWP08 - Install Generator VentilationICM_LM2500_IWP08-LSPT

CORRECTION VALUES FOR MEASURING WITH STEEL TAPESCorvalue

IWP04 - Set GeneratorICM_LM2500_IWP04

IWP23 - Turbine Package Dress-OutICM_LM2500_IWP23-LSPT

PWP10 - Instrument Air System Pre-CommICM_LM2500_PWP10

Temperature Indicator Check ListTempindck

CWP21 - AVR Dynamic TestingICM_LM2500_CWP21-LSPT

PIPE LINE LISTPipelinelist

IWP29 - Air Intake Path Pre-PSORICM_LM2500_IWP29

Mechanical Alignment Form Reverse Indicator ReadingMechform

Interim Change Notice


WP 406 00, Borescope InspectionLM2500-IND-GEK112767-007


Add Instructions for Gas Generator with Cast Fuel Manifold ReplacementLM2500-IND-GEK103089-020

Adds TMF maintenance check requirements for Chapter 11, Preventive MaintenanceLM2500-IND-GEK105048-027

Adds Additional Technical Information to WP 301 00LM2500-IND-GEK112859-004

Adds Additional Technical Information to Chapter 6LM2500-IND-GEK112859-002

Update the High Pressure Turbine / Rotor Removal ProcedureLM2500-IND-GEK97310-044

Update GE Legal Technical InformationLM2500-IND-GEK97310-048

Add Instructions for WP 241 00, Propulsion Gas Turbine Installation and CheckLM2500-CM-GEK103002-003

Add Instructions for WP 235 00, Gas Generator Assembly ReplacementLM2500-CM-GEK103002-002

Add Instructions for Gas Turbine with Cast Fuel Manifold ReplacementLM2500-IND-GEK103089-018

Add Instructions for Replacing No. 3 Bearing Stationary Oil Seal LM2500-IND-GEK112859-001

Add additional information for WP 411 00, Overspeed InspectionLM2500-IND-GEK112767-006

Adds additional information for Chapter 4, General Operation and TroubleshootingLM2500-IND-GEK97310-060

Add additional information for WP 505 00, Transfer of Gas Turbine To/From Shipping ContainerLM2500-IND-GEK97310-056


Add additional information for WP 431 00, Power Turbine Thrust Balance Cavity Pressure System Orifice Plate Selection.LM2500-IND-GEK112767-005

Add information to WP 500 00, Gas Generator ShippingLM2500-IND-GEK113997-002

Add Additional Information for Chapter 6, Service and Support RequirementsLM2500-IND-GEK105054-016

Add information to WP 504 00, Dockside Handling of Gas Generator, Power Turbine, and High Speed Coupling ShaftLM2500-CM-GEK109982-002


Update Thrust Balance Cavity Pressure System Orifice Plate Selection ProcedureLM2500-IND-GEK105048-021

Amends WP 240 00, Dockside Handling of Gas Generator and Power TurbineLM2500-CM-GEK50502-015


Amends WP 238 02, Gas Generator Assembly ReplacementLM2500-CM-GEK50502-014

Critical Parts Life Management InformationLM2500-IND-GEK105048-017

Add Instructions for WP 300 00, Gas Generator Assembly ReplacementLM2500-CM-GEK105164-002


Add Additional Information for Chapter 6, Service and Support RequirementsLM2500-IND-GEK105048_021

Work Package 128 00, Accoustic Sensor ReplacementLM2500-IND-GEK103089-025


Adds additional information for Addendum AC, Industrial Gas Turbine Model 7LM2500-PL-MGALM2500-IND-GEK97310-064

Add additional Information for SWP 503 01, Transfer of Gas Gener-ator To/From Shipping ContainerLM2500-IND-GEK97310-055

Add new SWP 128 01, Accoustic Sensor ReplacementLM2500-IND-GEK103089-024

Amends WP 238 01, Gas Generator Assembly ReplacementLM2500-CM-GEK50502-013

Add Gas Generator/Gas Turbine / Shipping Instructions for LM2500+G4 DLE - Models HB, HH, and RDLM2500-IND-GEK105048-019

Add Instructions for Gas Generator with Tubular Fuel Manifold ReplacementLM2500-IND-GEK103089-021



Add Instructions for Gas Turbine with Tubular Fuel Manifold ReplacmentLM2500-IND-GEK103089-019

Add Instructions for Replacing No. 3 / Bearing Stationary Oil Seal and Compressor Inlet Air SealLM2500-IND-GEK105048-018


Update Combustion Chamber / Inspection DataLM2500-IND-GEK103089-015

Adds TMF maintenance check requirements for Chapter 11, Preventive MaintenanceLM2500-IND-GEK105054-022

Adds additional information for Addendum AB, Industrial Gas Turbine Model 7LM2500-PH-NGA/MGA (STIG)LM2500-IND-GEK97310-063


Add additional Information for WP 502 00, Gas Generator/Gas Turbine Shipping Universal Con-tainer OnlyLM2500-IND-GEK97310-053


Add additional information for WP 502 00, Gas Generator/Gas Turbine Shipping-Cast Fuel ManifoldLM2500-IND-GEK103089-022

Adds additional information for WP 431 00, Power Turbine Thrust Balance Cavity Pressure System Orifice Plate SelectionLM2500-IND-GEK105048-028

Chapter 5, Periodic Inspection, Servicing, and Preventive MaintenanceLM2500-IND-GEK97310-058


Add additional information for Chapter 12, Critical Parts Life ManagementLM2500-IND-GEK112859-006

Add information to WP 501 00, Gas Generator Assembly ReplacementLM2500-CM-GEK109982-001

Update Critical Parts Life Management InformationLM2500-IND-GEK103089-014

Add Instructions for Replacement of Gas GeneratorLM2500-IND-GEK97310-057

Add Instructions for Replacing / No. 3 Bearing Stationary Oil SealLM2500-IND-GEK105048-020


Adds TMF maintenance check requirements for Chapter 5, Periodic Inspection, Servicing, and Preventative MaintenanceLM2500-IND-GEK103089-027

Add additional information for SWP 502 01, Gas Generator/Gas Turbine Shipping-Tubular Fuel ManifoldLM2500-IND-GEK103089-023

Add Instructions for WP 301 00, Gas Generator Assembly ReplacementLM2500-IND-GEK105054-018

Adds Additional Technical Information to Chapter 6LM2500-IND-GEK112767-001

Add additional information for Chapter 2, Functional DescriptionLM2500-IND-GEK103089-017

Chapter 5, Periodic Inspection, Servicing, and Preventative MaintenanceLM2500-IND-GEK103089-026

Add Instructions for Replacing No. 3 / Bearing Stationary Oil Seal and Compressor Inlet Air SealLM2500-IND-GEK105054-014




Adds TMF maintenance check requirements for Chapter 5,Periodic Inspection, Servicing, and Preventative MaintenanceLM2500-IND-GEK97310-059

Add Dual Fuel System Removal and Installation ProcedureLM2500-IND-GEK103089-016

Add Instructions for WP 500 00, Gas Generator ShippingLM2500-CM-GEK105164-003

Add Instructions for WP 300 00, Gas Turbine Assembly ReplacementLM2500-IND-GEK105048-022

Add Instructions for WP 301 00, Gas Generator Assembly ReplacementLM2500-IND-GEK105048-023


Adds additional information for Addendum AA, Industrial Gas Generator Model 7LM2500-GE-MGXLM2500-IND-GEK97310-062

Add Additional Information for Chapter 2, Functional DescriptionLM2500-IND-GEK97310-050


Add additional Information for WP 503 00, Transfer of Gas Genera-tor To/From Shipping Container and Shipping Container MaintenanceLM2500-IND-GEK97310-054

Add Instructions for Replacement of Gas TurbineLM2500-IND-GEK97310-051



Add Instructions for WP 502 00, Gas Generator/Gas Turbine ShippingLM2500-IND-GEK105054-019

Add Instructions for Replacement of Gas GeneratorLM2500-IND-GEK97310-052

Add Additional Information for WP 502 00, Gas Generator/Gas Turbine ShippingLM2500-IND-GEK105048-024


Adds additional information for Addendum Q, Industrial Gas Turbine Model 7LM2500-PE-NGXLM2500-IND-GEK97310-061

Adds additional information for Addendum AD,Industrial Gas Turbine Model 7LM2500-PE-MGALM2500-IND-GEK97310-065

Add Instructions for Replacing / No. 3 Bearing Stationary Oil SealLM2500-IND-GEK105054-015


Add Instructions for WP 300 00, Gas Turbine Assembly ReplacementLM2500-IND-GEK105054-017

Add information to WP 300 00, Gas Generator Assembly ReplacementLM2500-IND-GEK113997-001

Amends WP 238 00, Gas Generator Asssembly ReplacementLM2500-CM-GEK50502-012

Letters


LM2500-IND-04-005 - Event ReportingLM2500-IND-04-005

LM2500-IND-05-002 - Service Bulletin Compliance Record SubmissionLM2500-IND-05-002

LM2500-IND-06-07 - Generator Mechanical Oil Pump Gear Type Coupling Maintenance LM2500-IND-06-07

LM2500-IND-01-002 - Rigid Gas Fuel System (Safety Concern)LM2500-IND-01-002

LM2500-IND-08-03 - High Pressure Turbine Plane of Rotation Avoidance LM2500-IND-08-03

LM2500-IND-08-002 - Maintenance Dolly Tow Bar ModificationLM2500-IND-08-002

LM2500-IND-03-002 - Gas Generator Idle SpeedLM2500-IND-03-002

LM2500-CM-09-001 - Maintenance Dolly A-frame ModificationLM2500-CM-09-001

LM2500-AOE-09-001 - Maintenance Dolly A-frame ModificationLM2500-AOE-09-001

LM2500-IND-08-02 - Software Backup on Human Machine Interface (HMI) LM2500-IND-08-02

LM2500-IND-07-002 - Mark V LM Turbine Control System Software Error (Cancellation Notice)LM2500-IND-07-002

LM2500-IND-04-008 - Gas Turbine Inlet Maintenance for FOD PreventionLM2500-IND-04-008

LM2500-IND-04-002 - Inspection of DLE Combustor Inner Liner Mounting Bolts and CRF DiffusersLM2500-IND-04-002

LM2500-IND-99-005 - LM2500 Six-Stage Power Turbine Uncontained EventLM2500-IND-99-005

LM2500-IND-06-03 - LM2500 NOx Water Pump Event LM2500-IND-06-03

LM2500-IND-07-04 - Package Freezing Prevention (Winterization)LM2500-IND-07-04

LM2500-IND-06-05 - Generator Rundown Tank LeaksLM2500-IND-06-05

LM2500-IND-03-001 - Preventive Oil Leaks - Maintenance Best PracticesLM2500-IND-03-001

LM2500-IND-07-03 - Enclosure and Package Confined Space WarningLM2500-IND-07-03

LM2500-USCG-09-002 - Oils Approved for use in GE Marine EnginesLM2500-USCG-09-002

LM2500-USCG-09-001 - Maintenance Dolly A-frame ModificationLM2500-USCG-09-001

LM2500-LHD-09-002 - Oils Approved for use in GE Marine EnginesLM2500-LHD-09-002

LM2500-IND-97-002 - Authorized Service ProvidersLM2500-IND-97-002

LM2500-IND-06-005 - Package Window Viewing During Abnormal Operational Events LM2500-IND-06-005

LM2500-IND-96-001 - LM2500+ with 6 Stage PT - #7B Thrust Balance Orifice SizingLM2500-IND-96-001

LM2500-IND-06-006 - Used Aircraft Parts in LM Engines LM2500-IND-06-006

LM2500-IND-04-004 - LM2500 DLE Turbine Mid Frame InspectionLM2500-IND-04-004

LM2500-DDG-09-001 - Maintenance Dolly A-frame ModificationLM2500-DDG-09-001

LM2500-IND-07-01 - Safety Issue Engine Lifting CraneLM2500-IND-07-01

LM2500-IND-09-001 - Elimination of Mechanical ProtractorLM2500-IND-09-001

LM2500-DDG-09-002 - Oils Approved for use in GE Marine EnginesLM2500-DDG-09-002

LM2500-IND-03-004 - Industrial Engines Operating ProceduresLM2500-IND-03-004

LM2500-IND-04-001 - Vibration Monitor System MaintenanceLM2500-IND-04-001

LM2500-IND-07-004 - LM2500 + T3 Sensor (L47444P04) AlarmsLM2500-IND-07-004

LM2500-IND-04-006 - Hydraulic Starter Piston FailuresLM2500-IND-04-006

LM2500-IND-03-005 - DLE Operation with Sulfur in FuelLM2500-IND-03-005

LM2500-IND-02-004 - DLE CRF Diffuser Pin WearLM2500-IND-02-004

LM2500-LHD-09-001 - Maintenance Dolly A-frame ModificationLM2500-LHD-09-001

LM2500-IND-08-01 - Package Entry During Gas Turbine OperationLM2500-IND-08-01

LM2500-IND-99-007 - New Comprehensive Periodic Inspection and Maintenance TableLM2500-IND-99-007

LM2500-IND-97-001 - LM2500 and LM2500+ Vibration Monitor System SignalsLM2500-IND-97-001

LM2500-IND-99-006 - Humidity Control in LM Packages to Prevent Corrosion FatigueLM2500-IND-99-006

LM2500-IND-01-003 - Motoring after Hot ShutdownsLM2500-IND-01-003

LM2500-IND-02-001 - Inspection of Turbine Mid Frame (TMF) with Fabricated Outer Case All Industrial LM2500/LM2500+ with Thick Aft Flange TMFLM2500-IND-02-001

LM2500-IND-02-003 - Nox System Integrity (Safety Concern)LM2500-IND-02-003

LM2500-IND-06-004 - LM2500+ Rubber Coupling P/N L53721P01LM2500-IND-06-004

LM2500-IND-99-004 - Vibration Selection LogicLM2500-IND-99-004

LM2500-IND-08-003 - Protection of Bearings from External ContaminationLM2500-IND-08-003

LM2500-IND-05-001 - Engine control retrofitsLM2500-IND-05-001

LM2500-IND-98-001 - LM2500 Flex Joint ClampLM2500-IND-98-001

LM2500-IND-96-002 - LM2500 SAC/DLE Power Turbine Speed Sensor, PN L44780P01LM2500-IND-96-002

LM2500-IND-04-007 - LM2500 HP Recoup SizingLM2500-IND-04-007

LM2500-IND-02-002 - Fuel/Purge and NOx System Integrity (Safety Concern)LM2500-IND-02-002

LM2500-FN-09-002 - Oils Approved for use in GE Marine EnginesLM2500-FN-09-002

LM2500-IND-07-001 - LM2500 Extended Life Hot Section (ELHS) KitsLM2500-IND-07-001

LM2500-IND-00-002 - Rigid Gas Fuel System AlignmentLM2500-IND-00-002

LM2500-IND-06-06 - Reduction Gearbox Mechanical Pump Priming LM2500-IND-06-06

LM2500-IND-09-002 - Gas Turbine Lifting Equipment CertificationLM2500-IND-09-002

LM2500-IND-01-004 - DLE Gas Analysis Equipment InstallationLM2500-IND-01-004

LM2500-IND-99-003 - DLE TMF Scavenge Tube WearLM2500-IND-99-003

LM2500-IND-99-001 - Igniter Tip InspectionLM2500-IND-99-001

LM2500-IND-04-003 - LM2500 CRF/Diffuser Mounting BoltsLM2500-IND-04-003

LM2500-FN-09-001 - Maintenance Dolly A-frame ModificationLM2500-FN-09-001

LM2500-AOE-09-002 - Oils Approved for use in GE Marine EnginesLM2500-AOE-09-002

LM2500-IND-09-003 - Gas Turbine Lift Tool InspectionLM2500-IND-09-003

LM2500-IND-07-003 - Critical Instrumentation ProcurementLM2500-IND-07-003

LM2500-IND-09-01 - Gas Generator RemovalLM2500-IND-09-01

LM2500-IND-99-002 - GE Aero Energy Service/Product Letters and BulletinsLM2500-IND-99-002

LM2500-IND-01-001 - Lube Scavenge Alarm/Shutdown LimitsLM2500-IND-01-001

LM2500-IND-03-003 - Service BulletinsLM2500-IND-03-003

LM2500-IND-00-003 - Alarm & Shutdown LogicLM2500-IND-00-003

LM2500-IND-00-001 - HP Recoup MonitoringLM2500-IND-00-001

LM2500-IND-08-001 - GE Energy Learning Center Aeroderivative Product TrainingLM2500-IND-08-001

LM2500-IND-05-003 - Updated LM2500 and LM2500+ Periodic Inspection and Maintenance Table (Cancellation Notice)LM2500-IND-05-003

LM2500-CM-09-002 - Oils Approved for use in GE Marine EnginesLM2500-CM-09-002

Manual de Operao e Manuteno


Inspeo e Limpeza da Entrada de ArLM2500+G4_TP-01-WRpt

SP-D Descrio do GeradorLM2500+G4_SP-D-03pt

SP-D Descrio do SistemaLM2500+G4_SP-D-09pt

Limpeza de Campo do Sistema de Partida HidrulicaLM2500+G4_TP-06-HSFpt

SP-M Manuteno do SistemaLM2500+G4_SP-M-10pt




Procedimento de Amostragem do Gs CombustvelLM2500+G4_TP-07-SPpt

Kit de limpezaLM2500+G4_TP-01-FKpt

Procedimento de Armazenamento do PacoteLM2500+G4_TP-01-PSpt

SP-D Descrio do MotorLM2500+G4_SP-D-02pt


SP-O Operao do GeradorLM2500+G4_SP-O-03pt


Inspeo e Limpeza da Entrada de ArLM2500+G4_TP-08-WWpt


Requisitos Gs Natural CombustvelLM2500+G4_TP-07-NGpt

Especificao da Pureza da gua de Limpeza do CompressorLM2500+G4_TP-08-CCpt

Requisitos Combustvel LquidoLM2500+G4_TP-07-LFRpt

SP-O Operao do SistemaLM2500+G4_SP-O-09pt

Elemento Filtrante Inspeo e SubstituioLM2500+G4_TP-04-FEpt

Motor da Turbina de Gs - SumrioLM2500+G4_TP-02-GTEpt

SP-O Operao do PacoteLM2500+G4_SP-O-01pt

Sistemas CC e CA de Baixa Voltagem - SumrioLM2500+G4_TP-13-LVSpt



Amostragem de leo Lubrificante do GeradorLM2500+G4_TP-03-GLpt


Sistema de Monitorao e Controle - SumrioLM2500+G4_TP-12-CSpt


SP-M Manuteno do GeradorLM2500+G4_SP-M-03pt

Pgina de TtuloLM2500+G4-Title Page-PT

SP-M Manuteno do MotorLM2500+G4_SP-M-02pt


Requisitos leo LubrificanteLM2500+G4_TP-04-LOpt



Inspeo e Limpeza da Entrada de ArLM2500+G4_TP-09-AIpt

SP-O Operao do MotorLM2500+G4_SP-O-02pt



Procedimento de Umidificao de RolamentoLM2500+G4_TP-01-BWpt

Assunto de CapaLM2500+G4-Front Matter-PT

Limpeza de Campo do Sistema de leo Lubrificante do Gerador (Trocadores de Calor)LM2500+G4_TP-05-FFpt


Manuteno Geral de TemporaresLM2500+G4_TP-11-INSpt




Amostragem de leo Lubrificante da TurbinaLM2500+G4_TP-04-TLpt

SP-D Descrio do PacoteLM2500+G4_SP-D-01pt




Amostragem do Sistema de Combustvel LquidoLM2500+G4_TP-07-LFSpt

Esquema de Torque dos ParafusosLM2500+G4_TP-01-BTpt

Sistema de Proteo Contra Incndio - SumrioLM2500+G4_TP-10-FPpt

Detergente Lquido para Limpeza de CompressorLM2500+G4_TP-08-LDpt


SP-M Manuteno do PacoteLM2500+G4_SP-M-01pt



Limpeza do Sistema de leo Lubrificante da Turbina (Refrigerador por ventilao)LM2500+G4_TP-04-FFpt

Limpeza de Tubulao de Gs CombustvelLM2500+G4_TP-07-FGpt


Amostragem de leo do Sistema de Partida HidrulicaLM2500+G4_TP-06-HSOpt


Tabelas de ConversoLM2500+G4_TP-01-CTpt

Operation and Maintenance Drawings Manual


Magnehelic Differential Pressure Gage / (J04805)hs_dwy2000iom

Vent Breather Filter / (AE-229-110, AE-129-660-F)hs_ae-229

Water Wash System SamplingLM2500+G4_TP-08-WW

Generator 60HZ 11000V (BDAX75-193ERH)7217024-740148

Drawing 3E8501 Strainer Filler Cap / (3E8501-10, P-2MI-2)hs_tdc3e8501

Specification SC-10 Standard Cleaninig and Packaginghs_swksc-10

Drawing Assembly / (273800)hs_6601-01-019

Sump Type Filters, Additional Filtering Aids, Line and Inline Types & Other / (450M200)hs_nols-101

High Speed Multi - Contact Lockout Relays for Power Industry Applications / (7803A)hs_electroswitchlor-1

Bolt Torque ChartLM2500+G4_TP-01-BT

Offshore Watermist System / (APSMIST2500, 377A2228P0002, 382A1430P0001)hs_apswmist

8670/8674 Series Duplex Filter Assemblieshs_pllpihc8670-8674

Liquid Fuel RequirementsLM2500+G4_TP-07-LFR

Working and Joining Instructions for Noiseless Metal / (377A6648P0001)hs_aapWorking

2.16. International Drilling Cablehs_wferfoup1p8

Section 1. Pumps and Motors / (J05268)hs_bchsec01

Aquila Filter House for a LM2500+G4L2229-02-204

2.07. Switches Moduleshs_wfea200866

Stainless Steel Semi-Direct Lift Press 0 to 3000 psig 30800 Series / (J00097)hs_ak30800series

8670/8671/8674 Series Filters Service Instructionshs_pll8670-71-74

Instrumentation Diagram Auxiliary Systems7217024-740272

Flow and Instrument Diagram, Hydraulic Start System7217024-740232

PR10 Regulator - Standard / (382A1350P0001)hs_parkerr10

SP-M Package MaintenenceLM2500+G4_SP-M-01

Pressure Gauge Installation, Operation and Maintenance Manual / (382A1347P0001)hs_250-1353j

IO&M instructions for Model Number AE-129 / (AE-229-110, AE-129-660-F)hs_dolae-229

3500/20 Rack Interface Module129768-01

Bulletin 800E Plastic and Metal Operators / Push Buttons / (377A(2491P0001, 2492P0001, 2685P0001), 800E(2DL3X11, 2LX20), 800EP(F301W, HB32, LE4, LE5, LE7, SM22), 800H(NP-30, FPX6A1, 1HVX7M3, 1HVX7M3))hs_abrbull800e

R5200 Adjustable Right Anble Relief Valves / (377A6852P0001)HS_3009_001

2.21. Sounders Eexd(e), Weatherproof, GOST Certified DB3 & DB3Phs_wfe6ds094

Turbine Fire Protection PanelAPS800-507

TOPJOB'S Rail-Mounted Terminal Blocks with CAGE CLAMP'S Connection / (386A7126P0001)hs_wdr103600

PTX 650 Series Pressure Sensor / (386A6988P0001)hs_ptx65xseries

Standard Valves Series C73(50,80,82), S83(50,80,81,82) IO&Repair Manualhs_is-c7350-1

SP-M System MaintenenceLM2500+G4_SP-M-11

1.00. Cover Sheeths_wfelm2500_sheet

Bimetal thermometer Case Dimensions / (J00467)hs_250-1997-b

Filter Element Inspection and ReplacementLM2500+G4_TP-04-FE


Layout Junction Boxes7217024-740012

One Line Diagram7217024-740031

Drawing General Assembly Instrumentationhs_altabt058

Installlation & Start-Up Instructions Type 81, 81P, 83, 86 Safety-Relief Valves / (J04839)hs_05-9040-087

General Arrangement, Liquid Fuel Pump Skid7217024-740212

Installation Footprint, Foundation Loading Main Unit7217024-740224

Roxtec RM Modules Multidiameter Technology / (377A7829P0001)hs_rxcrm3-99

3E8501 Strainer Filler Cap / (3E8501-10, P-2MI-2)hs_tdc3e8501-10

Stainless Normally Closed Semi-Direct Lift Valves 31800 Series / (J00097)hs_31800series

Turbine Lube Oil System Flushing (Fin Fan Cooler)LM2500+G4_TP-04-FF

Spare parts list / (249A4946P0001)hs_abbm2ba71-132

Micronet Control System O&M Manual / (386A6830P0001, 386A6808P0001)hs_woob36204v2

I&M Instructions Bimetal thermometer with the Everyangle Connection / (J00467)hs_250-1068e_bimetal

ATP 0106-81 electrical Acceptance Test Procedure for Models with Isolated Groundhs_vicatp0106-81

Final Assembly Drawing Filter HouseABT705

Manual: NMO-2000-LM2500+ Inlet Bellmouth Nylon Screen Cover (J02486) / (J02486)hs_gea14477-3478

Drawing Circular Sights with Fuse Window / (A-2890-7)hs_oila-2890

Gasket Weights Based on 304 Wire, Flexible Super Filler and CS Outer Rings / (CG-1F-316, CG-1G-316)hs_fle304gaskt

Floating and Trunnion Mounted Ball Valves Soft and Metal Seated / (377A2300P0000)hs_kib0010602

SP-D System DescriptionLM2500+G4_SP-D-12

System Wiring Diagram, Gas and Liquid Fuel SAC7217024-740101

2.33. SAK - Serieshs_wfets32

Watts Ball Valves Manual / (377A2300P0000, J04840, J04842, J00822, J00016)hs_wwtballvalves

High Pressure Filtershs_pllhigh01

O&M Manual Fyrewash Gas Turbine Compressor Cleaning System / (LM2500BO)hs_roclm2500

Power Meter and Harmonic Analyzer I&O Manual / (382A7222P0001)hs_pm295_om

Drawing Final Assembly Filter House and Ductinghs_altabt705

System Wiring Diagram, Lighting and Distribution7217024-740093

Worksheet, Control System7217024-740146


Maintenance Instructions Type 81P Spring Operated Pressure Relief Valves / (J04847, J04839)agcotype81p-heb

Two Piece Ball Valves Series 7000/8000hs_wwtf-7000-8000

Industrial Ethernet Real-Time Switch with 9 Ports for Real-time Deterministic Performance and Ultra-Reliability / (382A9580P0001)hs_sxtt-gt-9es-2sc

Maintenance Instructions for Spring Operated Safety-Relief Valves / (J04839)hs_form05-9040-071

Drawing 2## Flame Arrester (6672) / (FF6672)hs_psldrw6672

Adjustable Pressure Switches Enclosure 3X for Weatherproof Applications / (132P41C6B, 132P4S129)hs_nd132p

Duragauge Pressure Gauge All Specifications / (J01994, J01996)hs_achbullentindu-1

In-Line Check Valves / (377A6887P0001)hs_inlinecheckvalves

Centaflex Couplings Information Sheet / (J04693)hs_techdatacat

Speed Switches Settings7217024-740967

SP-D Package DescriptionLM2500+G4_SP-D-01

Center Bonded Mounts Isolate Vibration Controls / (377A6928P0001, 377A6929P0001)hs_lmc-cb-sta


Aeroquip Performance Products / (2081-32-24S, 377A8076P0001, 377A2440P0001, 377A8077P0001, NH1600V400B0650, NH1600V250B0650)hs_eaqmc001

Low Medium Pressure Filtershs_plllow01


Bimetal Stem Thermometers / (38295K14)hs_mcc524

3500 Monitoring System Rack Configuration and Utilities Guide129777-01

Bimetal Thermometers Information (O&M Instruction) / (J00467)hs_achgaugetemp

System Wiring Diagram, Ventilation and Combustion Air7217024-740100

Direct Reading Flowmerers for Liquids ans Gaseshs_rcmc295


System Wiring Diagram, Loadshare7217024-740911

Drawing Assy Filter Duplexhs_pll9640E-1300065

Series 78 Platinum RTD Specifications / (377A6684P0001, 382A9518P0001, J00160, J00457)hs_series78

3500/44M Aeroderivative GT Vibration Monitor Module143490-01

Plug (Bridging & Short Circuiting), Protection Label (Screw) & Shield Connector / (382A1130P0001)hs_ds178746.15

3500/45 Position Monitor135545-01

Tube Fittings & Adapters / (J01199, J01201)hs_biseries64

Three Point Dead Bolt Lock / (5655X)hs_5647-x

Lift Arrangement7217024-740225

2.08. Combustible Gas Transmitter Model 505hs_det95-8472

Temperature Instruments Ordering Instructions / (75W0162SM260-S)hs_bulletinoh-1

Air Intake Inspection and CleaningLM2500+G4_TP-09-AI

SP-O System OperationLM2500+G4_SP-O-13

Plan and Elevation, Turbine Control Panel7217024-740014

Wiring Diagram, Turbine Control Panel Termination Cubicle7217024-740730

ATP 1213-79 Acceptance Test Procedure for Pressure Testing Electric Chip Detectors and Magnetic Drain Plugshs_tdcatp1213-79

Hydraulic Start System Field FlushingLM2500+G4_TP-06-HSF

Final Assembly Drawing Filter House and DuctingABT706

Magnetic Pickups and Proximity Switches for Electronic Controls / (386A3904P0001)hs_woo82510m


Flexible Drive Coupling Catalog / (M300-METRIC)hs_flexibledrive

Lubricating Oil RequirementsLM2500+G4_TP-04-LO

2.03. Modular Special Hazard Safety Controlshs_alle800systemb

1.02. General System Information and Overviewhs_wfelm2500_over

Straight-Through Couplings Brochure (Hansen ST Series) / (LL4-S26_LL4-T26)hs_hansenstseries

Product Bulletin 9640 Serieshs_pllnpb9640

2.19. CO2 Component Descriptionhs_kidde

HMK05 Series Hydraulic Filters / (HMK05-04)hs_f112074

Thermowells & Glass Thermometers / (3957K54)hs_mcc529

Unibody Flanged End Valves 150 & 300 Ansi Classhs_wwtf-2500

Package Storage ProcedureLM2500+G4_TP-01-PS

Push Button Installation and Mounting Instructions / (377A(2491P0001, 2492P0001, 2685P0001), 800E(2DL3X11, 2LX20), 800EP(F301W, HB32, LE4, LE5, LE7, SM22), 800H(NP-30, FPX6A1, 1HVX7M3, 1HVX7M3))hs_bulletin800h-800t

Overvoltage Protection for Instrumentation and Control Equipment / (382A5449P0001)hs_wdr106096

Circuit Breakers Thermal Magnitic Alternating Current Series GM / (GMU10LTV, GMU20LTV)hs_dsgmu

Simplex Screwed Basket Strainers 125F, 125FB, 125FCS, 125FSS / (2"-125F-SS-10MU)hs_muellerd6-d7

IO&M Instructions for 2HKB, HKB & HKSB Series Enclosures / (MPEX)hs_kllhkb

3500/22m Transient Data Interface161580-01

2.05. Control Switchhs_wfe60947-3

Control and Monitoring System - Tab ContentLM2500+G4_TP-12-CS


Specification Data Protect-IR Multispectrum IR Flame Detector with Pulse Output / (377A2226P0002)hs_detx3300a

Products Division Specializing in Stainless Steel and Aluminum Manual / (289172, 382A7006P0001, 571447, 76488, J05492)hs_alycatprod

3500/94 VGA Display Module148636-01

I&O Manual Valves Series VMK, VFK & VSV / (382A4068P0001, 382A1352P0001, 386A3175P0001, 386A3176P0001)hs_caxiomvmk

Foundation LoadingC-319411800

Drawing Size S22-9mm (LM-2500) Ameriflex Coupling / (300601)hs_amedd411440a

2.13. Specification Data Cataytic Combustible Gas Sensorhs_wfe90-1041-03

Accessories / (FB-A008X)hs_ap9911

8640 Series Duplex Rotolok Filter / (HC9604FKN13Z)hs_8640series


I&O Manual GS16 Gas Metering System Fuel Valve on Board Electronic Controller / (382A1209P0001)hs_woo26228a-gs16

EM and LQ Digital Driver O&C Manual / (382A4828P0001)hs_woo26159a

3500/72M Rod Position Monitor146479-01

Air Preparation Units General Line QIX High Efficiency Filters, Dial & Precision Regulators / (382A1350P0001)hs_wwt0303

Instruction Manual Model : KSFE / (J05428)hs_ksfemanual

2.01. Zag Rangehs_abtzag

Heavy Duty Handles / (5655X)hs_sec7handles

TOPJOB'S Rail-Mounted Terminal Blocks with CAGE CLAMP'S Connection / (210-229, 249-117, 249-125, 280-312, 280-402, 280-637, 280-641, 284-681, 377A2221P0000, 377A2447P0001, 780-455)hs_wgoblk2003


Instruction Manual Types 655 and 655R Actuators for Self - Operated Control / (J04849)hs_form1292

Fuel Control and Sequencer7217024-740145

Process Fluid Control Manualhs_pfcmanual


General IO&M Instructions for Aerovent Products / (249A4892P0001)hs_im1005-00

2.14. Instructions Infrared Hydrocarbon Gas Detector Point Watch Eclipse Model PIRECLhs_wfe95-8526

Industrial Networking: Industrial Ethernet: Rail Family: Unmanaged Rail Switches / (377A2637P0001)hs_hecrs2-tx

Service Intructions 8340 Series Duplex Filter Assemblieshs_pllsi8340

HMK05/25 DURAMAX Spin-ons / (HMK05-04, HMK25-04)hs_hmk05-25

FVS Series Long Twin Tube Fluerescent Luminaires / (FVS225)hs_colfvs225

Temperature Sensors and Accessories Volumme 1 / (377A6685P0001)hs_00813-0100-2654

Four Series of Check - All Valves / (J00044, J04841, J04850)hs_checkallcat-03

PR-1 Series, Adjustable Pressure Control Regulator / (377A6852P0001)HS_3012_001

Ultra Input Field Configurable Isolator / (377A2320P0001, G408-0001)hs_acig408_0001-1001

Area Classification Drawings Main Unit7217024-740690

ELPS Light Pak Emergancy Lighting System / (ELPS502)hs_colelps502

Gas Fuel Sampling ProcedureLM2500+G4_TP-07-SP

3500 Monitoring System Rack Installation and Maintenance Manual129766-01

System Wiring Diagram, Emergency Stop Loop7217024-740920

Medium Weight Oil Applications ARMTO-3 / (J00829)hs_chxarmto3

Flame Arrester Instalacion and Maintenance Instructions / (FF6672)hs_plsimi6670

2.34. CO2 Purge Switch Part WFCO2PS-A39Khs_wfewfco2ps-a39k

3500 Monitoring System Computer Hardware and Software Manual128158-01

2.24. Heat Detector Eexd, Eexem & Intrinsically Safe (Eexia) HD1 Rangehs_wfe6ds116

General Operating Manual for Valves / (382A4068P0001, 382A1352P0001, 386A3175P0001, 386A3176P0001)hs_cax040101

2.31. RS Series - Metal Oxide Resistorshs_wfersseries

Axial Piston Variable Pump AA4VG / (249A4931P0001, HU00157956)hs_bchaa4vg


Test Report LM2500+G4 SAC Gas Turbine Gas Generator 679-105679-105

Hose and Fittings Catalog Instalation and Maintenance / (714027)hs_ghxhos-Fit-cat

Fuel Gas Pipe CleaningLM2500+G4_TP-07-FG

System Wiring Diagram, Water Wash7217024-740117

Unmanaged Switches / (382A9580P0001)hs_sxtt-gt-9es

F Series Filter Installation Instructions / (382A1351P0001)hs_ini-206

Drawing 12A-F16L-50-BN-SSS / (382A1351P0001)hs_skj10803

Partial List of 1" & 2" Ratchet Tie Downs Currently Stocked / (J05077)hs_bri01

System Wiring Diagram, Generator Lube Oil System7217024-740106


Valves Series 1800 & 2800 ANSI Class 150 / (J04840,J04842 )hs_iom-18002800

2.11. Instructions IR Flame Detector X9800hs_wfe95-8554

Drawing Dimensional for Model 1151 Pressure Transmitters / (J04817)hs_ero01151-0466


General Dimension 50EI60L Hermetically Sealed Bimetal Dial Thermometer / (J00467)hs_drawingngp70

Proportional Relief Valves R Series / (382A4809P0001)swagelokrseries

8340 Series Duplex Filterhs_pllpihc8340

2.29. Series FS 84/99 Fire Safe High Performance 3 Piece Ball Valveshs_wfefs8499

Altair Inlet Filtration Systemshs_altl2229m000

Fire Protection System - Tab ContentLM2500+G4_TP-10-FP


Valve List (Sorted by Description) Catalog / (10P053, J04843, J04835)hs_dragonvalves1.3

Water Mist Fire Suppression SystemAPSMIST2500

Instruction Book M3425A Generator Protection / (382A5582P0001)hs_m_3425a_ib

System Wiring Diagram, Vibration7217024-740120

GS16 Gas Valve with on Board Driver / (382A1209P0001)hs_woo03284b-gs16

Drawing Assy Filter Duplexhs_pll9640E-1300207

Warranty Request FormLM2500+G4_TP-01-WR

3500/53 Overspeed Detection System134939-01


Reciver Gauges Type 1009 Stainless Steel / (382A1347P0001)hs_ach109

General Arrangement, Auxiliary Skid7217024-740218

3500/42M Proximitor/Seismic Monitor143489-01

3615 Industrial PCs 15.0" LCD Flat Panel Display / (216A4089P0001)hs_xyc361500e

Shipping Data7217024-740226

Pulsation Dampener Type 1106 (I&M Instructions) / (1112SD)hs_aspuldam1106

2.28. Installation & Adjusting Instructions QZM & QZEhs_wfep105076

Drawing Outline Installation for Model 91 Thermowell / (377A6685P0001)hs_ero00091-0051


Fluid Control Components / (249A4269P0001)hs_hok6100

Combustion & Ventilation Air Intake Filtration System (IO&M Manual) / (249A4954P0001)hs_aft80040-l1127

Front MatterLM2500+G4-Front Matter

Window Sights / (A-2890-7)hs_oila-2890-7

Bill of Materials / (249A4946P0001)hs_gecList01

DriveIT Low Voltage Motors - Manual for M3000 and M2000 Ranges / (386A6752P0001)hs_abbopsman

4375 Strobe Hazardous Location Strobe / (377A2248P0002)hs_tei4375

SP-D Generator DescriptionLM2500+G4_SP-D-03

LQ25 Valve Actuator Outline Drawing / (382A5323P0001)hs_wolq25fuel

Spectra GT30 Gas Turbine Flame Sensor Applications / (J04937)hs_atkgt30

Thermocouple MaintenanceLM2500+G4_TP-11-INS

Bearing Wetting ProcedureLM2500+G4_TP-01-BW

CBB and CBC Series Mounts Data Sheet / (377A6928P0001, 377A6929P0001)hs_cbb-cbcseries

Crosby Shackles / (1019490)hs_blpg-209-213-2130

3500/40M Proximitor Monitor Module143488-01

8670 Filter Series Service Instructionshs_pllsi8670

Flow and Instrument Diagram, Turbine Lube Oil System7217024-740244

O&M Manual Switchgear 50/60Hz, 1000MVA TM2500 Unit 1 / (93552)hs_stsunit1-60

Liquid Level Gage Front Mount with Needle Valves, Pipe Adapters / (G608-12-A-3-5)hs_ludf327-8

Test Report LM2500+G4 SAC Gas Turbine Gas Generator 679-103679-103

General Arrangement - Line CubicleB-963732200

2.12. Instructions Duct Mount Kit Q900hs_wfeq900

Threaded ConnectorsNot for Lifting / (382A4159P0001)hs_mcc1362

3500/60 and 61 Temperature Monitor134542-01

Acceptance Test Procedure for Land Gas Turbine Electrical Cables / (216A3600P0001, 216A3604P0001, 216A3605P0001, 216A3606P0001, 216A3607P0001, 216A3608P0001, 382A6535P0001, 382A6604P0001, 382A6626P0001, 382A6628P0001, 382A6646P0001, 382A6649P0001)hs_harhs51403

Watts Split Body Flanged End Ball Valveshs_wwtsplit

Carbon Steel Ball Valves Series C-7500, C-7800hs_wwtf-c7000

Liquid Detergent for Compressor CleaningLM2500+G4_TP-08-LD

MGS18 DS 2.5" All Stainless Steel Construction / (377A6852P0001)HS_3011_001

Cast Stainless Steel Screwed & Socket Weld "Y" Strainers / (377A7898P0001)hs_c25-581_ss-582ss

Thermostatic Valves Model C / (377A7866P0001)hs_form193a971

SPM-D10/YB Synchronizing Unit Manual / (377A6816P0001)hs_woo37134

Drawing Assembly Layout Relief Regulator Valve / (714332)hs_714332

Skiner Valve Two Way, Three Way, and Four Way Solenoid Valves / (377A6920P0001)hs_pkrcfl00897

9850/9851 Series High Pressure Filters Assemblyhs_pllpihc9850-9851


GS3/LQ Valve Driver Used with LQ3, LQ25, LQ25T / (382A5323P0001)hs_wo40175

3500/50 Tachometer Module134938-01

Self-Drilling Screws / (377A1122P0000)hs_mcc2975

Emergency Lighting / (377A6723P0001)hs_col67-84

Pre Engineered Hi-Fog systems (GPU)hs_hfgdiom98

Interconnect Cable Schedule7217024-740009

Flushing KitLM2500+G4_TP-01-FK

2.23. Heat Detector Hazardous Locations, Weatherproof HD1 Rangehs_wfe6dsus24

Fan and Filter Units (SK 33 XX XXX) / (377A6807P0001)hs_ritsk33

Standard Terminal Blocks (Pag 40) / (11512017)hs_ds115120.17

2.15. Electrical Equipment for Hazardous Areas Control Stationshs_wfeil60077

Aquila Filter House P&IDL2229-02-900

Title PageLM2500+G4-Title Page

Hydraulics Product Catalog with Preferred & Spotlight Delivery Programs Section / (J05268)hs_bchintro

2.09. Combustible Gas Calibration Kit 225130 Serieshs_det958382

Conversion TablesLM2500+G4_TP-01-CT

Lube Oil Filter / (AC-B244F-2440Y1)hs_acpadb24424y1

SP-M Engine MaintenenceLM2500+G4_SP-M-02

Schedule Motor Control Center7217024-740035

SP-O Generator OperationLM2500+G4_SP-O-03

Ameriflex High Performance Couplings Installation and Maintenance Manual / (300601)hs_367sh


Drawing Final Assembly Filter House and Ductinghs_altabt706

Flame Arrester Series 670 Specifications / (FF6672)hs_v670_v6670

1.03. Nema Enclosure Manufacturing Structural Skid Anlysis 10 Bottle CO2 Skidhs_wfe4avw

GLO Field Flushing (Fin-Fan)LM2500+G4_TP-05-FF

Outline In

Documents

list of the manuals loaded for PBOil.doc