A) Assembly Data (allowable loads, torque requirements and Factor of Safety used)

B) Customised project name or detail

Email your connection requirement (contact details on next sheet)

Example shown: GC001-1

As part of its extensive Technical Support service Lindapter, the innovators of steelwork clamping fixings, can design a bespoke connection based on your specific requirements free of charge in three easy steps...

C) Your company name

D) Lindapter product requirements

E) Additional dimensions for precise fabrication

Lindapter’s experienced Engineers will devise your

bespoke solution

1 32

An Engineer will send you a design drawing,

as below> >

Each drawing includes:

www.Lindapter.com

FREE CONNECTION DESIGNAvailable now from

A

Top BeamFlange Width = 203mmFlange Thickness = 15.5mm

Lower BeamFlange Width = 102mmFlange Thickness = 6mm

10

116

218

180

270

14 THRU

DETAIL A SCALE 1 : 1.5

M12 x 70mm Long Setscrew, PropertyClass 8.8, with Class 8 Nut & Plain Washer

Lindapter B12L Clamp

Lindapter A12M Clamp

Lindapter P1S12 Packer

Location Plate

For combined loadings the current relevant nationalstandard should be taken into consideration

Assembly Data:

Static Tensile SWL = 23.2 kNFactor of Safety :

5 : 1Static Slip Resistance

SWL = 1.4 kNFactor of Safety :

5 : 1Lindapter Fastener Tightening Torque = 69 Nm

GC001-1 Connection Details

DWG. NO. REV.

CHECKEDDATE

WEIGHT:

DESCRIPTIONREV. DATEBY

0SWXXXX-XX

CUSTOMER ENQUIRY N.

SCALE:

www.lindapter.com

DRAWN

DRAWING TITLE

GENERAL NOTES:

NOT TO SCALE

DO NOT SCALE THIS DRAWING1.THIS DRAWING AND THE COPYRIGHT THEREIN ARE THE 2.PROPERTY OF LINDAPTER INTERNATIONAL. IT IS ISSUED ON THE CONDITION THAT IT MUST NOT BE USED, COPIED, DISTRIBUTED OR EXHIBITED WITHOUT WRITTEN PERMISSION AND CONSENT. THE DRAWING MUST ALSO NOT BE USED FOR ANY OTHER PURPOSE THAN WHICH IT IS ISSUED.IT IS THE RESPONSIBILITY OF THE ENGINEER TO PERFORM 3.ALL REASONABLE CHECKS ON THE SUPPORTING AND SUPPORTED MEMBERS. THAT IS LOCAL TO THE CONNECTION AND THE LINDAPTER COMPONENTS, BOTH FOR THE LOAD APPLIED AND THE CLAMPING FORCE GENERATED FROM THE TIGHTENING OF THE FASTENERS.WHERE NECESSARY WORKMANSHIP FOR ITEMS SHOWN 4.ON THIS DRAWING SHOULD COMPLY WITH THE RELEVANT SECTIONS OF THE NATIONAL STRUCTURAL STEELWORK SPECIFICATION (NSSS) FOR BUILDING CONSTRUCTION 5TH EDITION CE MARKING VERSION.IF FELT NECESSARY, WHERE EXCESSIVE VIBRATION MAY BE 5.A CONCERN, IT IS ACCEPTABLE FOR CERTAIN TYPES OF ANTI-VIBRATION LOCKING DEVICES SUCH AS, BUT NOT LIMITED TO, PROPRIETARY WASHERS AND NUTS TO BE USED WITH LINDAPTER COMPONENTS AND/OR ASSEMBLIES; SPRING WASHERS OF ANY TYPE ARE NOT RECOMMENDED. IN THESE SITUATIONS IT IS IMPORTANT THAT THE MANUFACTURER'S INSTALLATION INSTRUCTIONS ARE FOLLOWED. NO GUARANTEES OR WARRANTIES ARE IMPLIED.

DRAWING NOTES:

PROJECT

DIMENSIONS ARE IN MM1.TOLERANCES: 2.ANGULAR: BEND 3.MATERIAL COATINGS TO BE SPECIFIED BY THE ENGINEER 4.

A

B

D

C

E

FREE CONNECTION DESIGNAvailable now from

Why choose Lindapter?Lindapter’s experienced team of Engineers ensures an efficient specification process from start to finish, aiming to create a bespoke solution that delivers on cost and performance, ultimately saving you time and money.

Lindapter provides drawings in 2D and interactive 3D formats as well as CAD files that are suitable to import into all major software applications. We can even customise the drawing by adding your project name so it’s ready for plan checking immediately, thereby reducing design time.

Simply provide the details listed on the right and Lindapter will do the rest!

If you would like Lindapter to design your bespoke connection, please make sure to have the following:

1. Member sizes to be used or flange width and thickness

2. Loads to be resisted (eg. 10kN tension and 15kN slip)

3. General arrangement sketch and/or verbal description*

4. Project Name / Title (optional)

5. Project Location (optional)

*See Lindapter’s catalogue for different configurations

The Service Free connection design is just a small part of Lindapter’s service. We offer comprehensive design and support, tailoring our products to your application:

££ £3D>

Free design proposal

2D / 3D drawings

Quotation SupplyInstallation guidance

> > >

>> For simple Girder Clamp connections try the Assembly Selector today at www.Lindapter.com <<

Contact Lindapter today

Tech Support: support@Lindapter.com / General Enquiries: enquiries@Lindapter.com / T: +44 (0) 1274 521444

What we require...

www.Lindapter.com

A

Top BeamFlange Width = 203mmFlange Thickness = 15.5mm

Lower BeamFlange Width = 102mmFlange Thickness = 6mm

10

116

218

180

270

14 THRU

DETAIL A SCALE 1 : 1.5

M12 x 70mm Long Setscrew, PropertyClass 8.8, with Class 8 Nut & Plain Washer

Lindapter B12L Clamp

Lindapter A12M Clamp

Lindapter P1S12 Packer

Location Plate

For combined loadings the current relevant nationalstandard should be taken into consideration

Assembly Data:

Static Tensile SWL = 23.2 kNFactor of Safety :

5 : 1Static Slip Resistance

SWL = 1.4 kNFactor of Safety :

5 : 1Lindapter Fastener Tightening Torque = 69 Nm

GC001-1 Connection Details

DWG. NO. REV.

CHECKEDDATE

WEIGHT:

DESCRIPTIONREV. DATEBY

0SWXXXX-XX

CUSTOMER ENQUIRY N.

SCALE:

www.lindapter.com

DRAWN

DRAWING TITLE

GENERAL NOTES:

NOT TO SCALE

DO NOT SCALE THIS DRAWING1.THIS DRAWING AND THE COPYRIGHT THEREIN ARE THE 2.PROPERTY OF LINDAPTER INTERNATIONAL. IT IS ISSUED ON THE CONDITION THAT IT MUST NOT BE USED, COPIED, DISTRIBUTED OR EXHIBITED WITHOUT WRITTEN PERMISSION AND CONSENT. THE DRAWING MUST ALSO NOT BE USED FOR ANY OTHER PURPOSE THAN WHICH IT IS ISSUED.IT IS THE RESPONSIBILITY OF THE ENGINEER TO PERFORM 3.ALL REASONABLE CHECKS ON THE SUPPORTING AND SUPPORTED MEMBERS. THAT IS LOCAL TO THE CONNECTION AND THE LINDAPTER COMPONENTS, BOTH FOR THE LOAD APPLIED AND THE CLAMPING FORCE GENERATED FROM THE TIGHTENING OF THE FASTENERS.WHERE NECESSARY WORKMANSHIP FOR ITEMS SHOWN 4.ON THIS DRAWING SHOULD COMPLY WITH THE RELEVANT SECTIONS OF THE NATIONAL STRUCTURAL STEELWORK SPECIFICATION (NSSS) FOR BUILDING CONSTRUCTION 5TH EDITION CE MARKING VERSION.IF FELT NECESSARY, WHERE EXCESSIVE VIBRATION MAY BE 5.A CONCERN, IT IS ACCEPTABLE FOR CERTAIN TYPES OF ANTI-VIBRATION LOCKING DEVICES SUCH AS, BUT NOT LIMITED TO, PROPRIETARY WASHERS AND NUTS TO BE USED WITH LINDAPTER COMPONENTS AND/OR ASSEMBLIES; SPRING WASHERS OF ANY TYPE ARE NOT RECOMMENDED. IN THESE SITUATIONS IT IS IMPORTANT THAT THE MANUFACTURER'S INSTALLATION INSTRUCTIONS ARE FOLLOWED. NO GUARANTEES OR WARRANTIES ARE IMPLIED.

DRAWING NOTES:

PROJECT

DIMENSIONS ARE IN MM1.TOLERANCES: 2.ANGULAR: BEND 3.MATERIAL COATINGS TO BE SPECIFIED BY THE ENGINEER 4.