Upload
others
View
6
Download
0
Embed Size (px)
Citation preview
433-1 - Lintronic InfraRed Radio-wave Computer Interface - LIRCILIN-138 / LinTronic InfraRed Signal Converter and Computer Interface
lintronic.dk Revised: 141217
The LIN-138 is a Signal Converter holding:- IR low-power output and high-power front booster- RS232 comport- digital input- heavy duty relay
LIN-138 is a cut-down version of the popular TT455-RT-238.
LIN-138
LinTronic InfraRed Signal Converter & Computer Interface
433-1 - Lintronic InfraRed Radio-wave Computer Interface - LIRCI
lintronic.dk
SemiTransparent DarkRed plastic enclosure, compact design ( W:120 x H:65 x D:40 mm )- Plastic is infrared transparent offering long range- When inserted into a cabinet, or left close to other products, the cabinet appears dark/black
HighPower DualBand LongRange InfraRed Booster (32-56 Khz)- Supports products from the LinTronic Database (more than 80.000 commands)
2-way RS232 communication comport (2.400 - 38.400 bps)- Controls projectors, light systems, computer, amx, crestron, etc.- RS232 commands can be transmitted by radio signals across the house
1 pcs digital input can be triggered by external contact
1 pcs heavy-duty relay output (5 amps)
Cooperates with:TT455-R-238 Signal ConverterLIN-433 Signal ConverterRELAY 208 8-channel relay board
shown without electronics
LIN-138 / LinTronic InfraRed Signal Converter and Computer Interface
433-1 - Lintronic InfraRed Radio-wave Computer Interface - LIRCI
lintronic.dk
TRIGGERS
The LIN-138 can be triggered by:
- infrared remote controls- B&O remote control (extra IR receiver required)- Digtal input triggerede by:- cameras, relays, switches, buttons- RS232 from computers and controllers- and much more
Triggers
ACTIONS
The LIN-138 can control:
audio/video products, like:amplifiers, cd, dvd, mediacenters
tvs, projectors, screenscomputers, controllers, HomeAutomation software
relays, motorsand much more
Actions
LIN-138 / LinTronic InfraRed Signal Converter and Computer Interface
MOTHERBOARD
Relay inRelay outGroundDigital inputIR low-power outputIR inputRS232Power (12 volt)
Extension board for LIN-433Heartbeat LEDHigh-Power front IRConfirmation LED36-40 KHz IR receiverMicroController
LIN-138 / LinTronic InfraRed Signal Converter and Computer Interface
HeartBeatBlinks every seconds whenprogram is running.
Program must be runningnot later than 5 seconds afterpower is applied.
IR indikatorBlinks when detecting IRor background noise.
LIN-138 / LinTronic InfraRed Signal Converter and Computer Interface
REAR LOOKFRONT LOOK
Confimation LED 36-40 KHz Rx
IR BOOSTER
POWER B&O INPUT
RS232 IR OUT RELAY
LIN-138 / LinTronic InfraRed Signal Converter and Computer Interface
Power supply
1.5V 12V
PowerAdap-003 / 004
100-240 vac5 0 / 6 0 H z
+-
12 volt2.1 mm
When power is applied, the character ^ is transmitted on the comport right away,to indicate to the computer that the product is asking for new firmware.
The product will wait for 3 seconds. During these 3 seconds the front LED will flash.If no correct answer is received from the computer then the product will send out: <0001010082>
You can check that this happens in the DataSampler of the Configurator.
Also the confirmation LED will blink when receiving a Trigger or carrying out an Action.
Confirmation LED
LIN-138 / LinTronic InfraRed Signal Converter and Computer Interface
RS232 interface
A B C
A B
C
Jack connector seenfrom solderside
5 4 3 2 1
9 8 7 6
A = pin 2 = TXB = pin 3 = RXC = pin 5 = GDN
DB09-female3.5 stereo jack
ComCab-004
LIN-138 / LinTronic InfraRed Signal Converter and Computer Interface
B&O receiver interface
C B A
A B
C
Jack connector seenfrom solderside
1 - C Ground2 - A 5 volt3 - B IR signal
B&OTT-IR-8087030
12
34
5
LIN-138 / LinTronic InfraRed Signal Converter and Computer Interface
Low-power IR outputREAR
TT-IR-ET03
3-way high-power IR booster outputFRONT
You can check the LED flasheswith mobile in camera mode
LIN-138 / LinTronic InfraRed Signal Converter and Computer Interface
Digital input
1 2 3 4
GND
Do not connect 12 volt.Polarity-free contacts only.
The input is known in the Memory Map as: Digital Input 1
LIN-138 / LinTronic InfraRed Signal Converter and Computer Interface
Internal relay
Relay in
Relay out
Low-voltage only.Not designed for 115-230 vac.
1 2 3 4
The relay is controlled in the Memory Map as: LinTronic, LIN-138, Relay
433-1 - Lintronic InfraRed Radio-wave Computer Interface - LIRCI
lintronic.dk
IR front-booster
RS-232
Example of use, B&O:With a B&O remote, you can control products by infrared, RS232 or relay.You can control products in the same room, or you can control products in a cabinetor in other rooms.
Relay
low-power IRIR
Room 1 Room 2 orcabinet
LIN-138 / LinTronic InfraRed Signal Converter and Computer Interface
433-1 - Lintronic InfraRed Radio-wave Computer Interface - LIRCI
lintronic.dk
IR front-booster
RS-232
Example of use, B&O:With a B&O remote, you can control products by infrared, RS232 or relay.You can control products in the same room, or you can control products in a cabinetor in other rooms.
Relay
low-power IRIR
Room 1
Room 2
Room 3 orcabinet
LIN-138 / LinTronic InfraRed Signal Converter and Computer Interface
433-1 - Lintronic InfraRed Radio-wave Computer Interface - LIRCI
lintronic.dk
IR front-booster
RS-232
Example of use, computer/controller:Crestron, AMX, computer or any other controller with USB or RS232, can sendcommands to control the LIN-138.
RelayUSB/RS232: ComCab-003
RS-232: ComCab-004
low-power IR
LIN-138 / LinTronic InfraRed Signal Converter and Computer Interface